Preliminary DBL201G THRU DBL209G Single Phase 2.0 AMPS. Glass Passivated Bridge Rectifiers Voltage Range 50 to 1400 Volts Current 2.0 Amperes DBL Features Glass passivated junction Ideal for printed circuit board Reliable low cost construction utilizing molded plastic technique High surge current capability High temperature soldering guaranteed: 260℃ / 10 seconds at 5 lbs., ( 2.3 kg ) tension Small size, simple installation Leads solderable per MIL-STD-202 Method 208 DBLS Dimensions in inches and (millimeters) Maximum Ratings and Electrical Characteristics Rating at 25℃ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20% Type Number Symbol DBL DBL DBL DBL DBL DBL DBL DBL DBL 201G 202G 203G 204G 205G 206G 207G 208G 209G Units DBLS DBLS DBLS DBLS DBLS DBLS DBLS DBLS DBLS 201G 202G 203G 204G 205G 206G 207G 208G 209G Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current @TA = 40℃ Peak Forward Surge Current, 8.3 ms Single Half Sine-wave Superimposed on Rated Load (JEDEC method ) Maximum Instantaneous Forward Voltage @ 2.0A Maximum DC Reverse Current @ TA=25℃ at Rated DC Blocking Voltage @ TA=125℃ Typical Thermal Resistance (Note) Operating Temperature Range Storage Temperature Range VRRM 50 100 200 400 VRMS VDC 35 70 140 280 50 100 200 400 600 800 1000 1200 1400 V 420 560 600 800 1000 1200 1400 V V 700 840 980 I(AV) 2.0 A IFSM 50 A VF 1.15 1.30 V IR 10 500 uA uA RθJA RθJL 40 15 -55 to +150 -55 to +150 ℃/w TJ TSTG ℃ ℃ Note: Thermal resistance from Junction to Ambient and from Junction to Lead Mounted on P.C.B. with 0.51 x 0.51” (13 x 13mm) Coper Pads. 10.13.2005/rev. a RATINGS AND CHARACTERISTIC CURVES (DBL201G THRU DBL209G) FIG.1- MAXIMUM DERATING CURVE FOR OUTPUT RECTIFIED CURRENT FIG.2- MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT PER BRIDGE ELEMENT 60 PEAK FORWARD SURGE CURRENT. (A) AVERAGE FORWARD CURRENT. (A) 2.0 .06" (1.5mm) PCB Copper Pauls .51" x .51" (13mm x 13mm) 1.0 60Hz RESISTIVE OR INDUCTIVE LOAD 0 20 40 60 80 100 120 Tj=25 0C Single Sine - Wave (JEDEC Method) 50 40 30 20 10 0 140 150 1 2 o AMBIENT TEMPERATURE. ( C) 4 6 10 20 40 NUMBER OF CYCLES AT 60Hz FIG.3- TYPICAL REVERSE CHARACTERISTICS PER BRIDGE ELEMENT FIG.4- TYPICAL FORWARD CHARACTERISTICS PER BRIDGE ELEMENT 10 100 INSTANTANEOUS FORWARD CURRENT. (A) INSTANTANEOUS REVERSE CURRENT. ( A) Tj=125 0C 10 1.0 Tj=25 0C .10 .01 0 20 40 60 80 100 120 FIG.5- TYPICAL JUNCTION CAPACITANCE PER BRIDGE ELEMENT CAPACITANCE.(pF) 100 1 1.0 Tj=25 0C f=1.0MHz Vsig=50mVp-p 10 REVERSE VOLTAGE. (V) DBL208G-209G 0.1 0 Tj=25 C PULSE WIDTH-300 S 2% DUTY CYCLE .01 140 PERCENT OF RATED PEAK REVERSE VOLTAGE. (%) 10 DBL201G-207G 1 100 0.4 0.6 0.8 1.0 FORWARD VOLTAGE. (V) 1.2 1.4 60 100