AAC CRL14R020FQM Current sensing chip resistor Datasheet

CURRENT SENSING CHIP RESISTORS
HOW TO ORDER
CRL10
R020
J
N
M
Packaging
M = Tape/Reel
FEATURES
B = Bulk
TCR (PPM/°°C)
K=+100
L=+200
O=+400
Q=+600
N=+300
M=+500
Tolerance (%)
F = +1
G = +2
J = +5
Current Sensing Resistor
Reference Standard = IEC 60115-8, JIS C 5201-8
EIA Resistance Value
Standard decade values
Series Size
CRL05 = 0402
CRL16 = 0603
CRL10 = 0805
CRL18 = 1206
CRL14 = 1210
DERATING CURVE
CRL12 = 2010
CRL01 = 2512
CR12S = 0612
CR1S = 3720
CRL02 = 7520
DIMENSIONS (mm)
Size
0402
0603
0805
1206
2010
2512
3720
0612
L
1.00 + 0.05
1.60 + 0.10
2.00 + 0.15
3.10 + 0.15
5.00 + 0.15
6.30 + 0.15
3.75 + 0.20
7.50 + 0.20
W
0.50 + 0.05
0.80 + 0.10
1.25 + 0.15
1.55 + 0.15
2.50 + 0.15
3.10 + 0.15
2.00 + 0.20
2.00 + 0.20
D1
0.25 + 0.10
0.30 + 0.20
0.30 + 0.20
0.50 + 0.30
0.60 + 0.30
0.60 + 0.30
0.40+ 0.20
0.40+ 0.20
D2
0.20 + 0.10
0.30 + 0.20
0.30 + 0.20
0.40 + 0.20
0.50 + 0.25
0.50 + 0.25
0.40 + 0.20
0.40 + 0.20
Tt
0.32 + 0.05
0.45 + 0.10
0.50 + 0.10
0.60 + 0.10
0.60 + 0.10
0.60 + 0.10
0.60 + 0.10
0.60 + 0.10
±300
0.100 ~ 0.200
0.100 ~ 0.910
Max TCR (ppm/°C) Per Resistance Range in Ω
±250
±200
±150
0.220 ~ 1.000
0.010 ~ 0.200
0402
0603
±1, ±2, ±5
±1, ±2, ±5
0805
±1, ±2, ±5
0.100 ~ 0.910
0.010 ~ 0.091
1206
1210
2010
±1, ±2, ±5
±1, ±2, ±5
±1, ±2, ±5
0.100 ~ 0.910
2512
±1, ±2, ±5
0.010 ~ 0.091
0.100 ~ 0.910
0.100 ~ 0.910
0.010 ~ 0.091
0.100 ~ 0.910
3720
0612
±1, ±2, ±5
±1, ±2, ±5
0.001 ~ 0.050
0.100 ~ 0.200
±100
0.021 ~ 0.910
0.005 ~ 0.020
0.210 ~ 0.910
0.002 ~ 0.030
0.005 ~ 0.030
Rated
Power
1/16 W
1/10 W
1/8 W
1/4 W
1/4 W
1/2 W
0.001 ~ 0.010
1W
0.001 ~ 0.030
0.001 ~ 0.010
0.5W & 1W
0.5W & 1W
Operating Temp. Range is
-55°C ~ + 125°C
Tolerance
(%)
Operating Current I = √(P/R)
Size
Operating Voltage V = √(P*R)
RATING & CHARACTERISTIC
PERFORMANCE
Item
Temp. Coefficient of Resistance
Short Time Overload
Dielectric Withstand Voltage
Insulation Resistance
Thermal Shock
Load Life
Humidity (Stable State)
Resistance to Dry Heat
Low Temperature Operation
Bending Strength
Solderability
Resistance to Soldering Heat
Specification
As Spec
±(0.5% + 0.05Ω)
By type
>1000M Ω
±(0.5% + 0.05Ω)
±(1% + 0.05Ω)
±(1% + 0.05Ω)
±(0.5% + 0.05Ω)
±(0.5% + 0.05Ω)
±(0.5% + 0.05Ω)
95% min. Coverage
±(0.5% + 0.05Ω)
Test Method
~
MIL-STD-202F, Method 304 304 +25/-55/+25/+125/+25°C
JIS-C-5202-5.5 RCWV*2.5orMax Overloading Voltage 5 seconds
MIL-STD-202F, Method 301 Apply Max Overload Voltage for 1 minute
MIL-STD-202F, Method 302 Apply 100VDC for 1 minute
MIL-STD-202F, Method 107G -55°C ~ + 150°C, 100 cycles
MIL-STD-202F, Method 108A RCWV 70°C, 1.5 hrs ON, 0.5 hrs off, 1000 ~ 1048 hrs
MIL-STD-202F, Method 103B 40°C, 90~95%RH , RCWV 1.5 hrs ON, 0.5 hrs OFF, total 1000 ~ 1048 hrs
JIS-C-5202 7.2 96 hours @ +125°C without load
JIS-C-5202 7.1 1 hour, -65°C followed by 45 minutes if RCWV
JIS-C-5202 6.1.4 Bending Amplitude 3mm for 10 seconds
MIL-STD-202F, Method 208H 235°C±5°C, 2±0.5 (sec)
MIL-STD-202F, Method 210E 260±5°C ,10±1second
The content of this specification may change without notification 5/15/2015
American Accurate Components, Inc.
188 Technology Drive, Unit H, Irvine, CA 92618
TEL: 949-453-9888 FAX: 949-453-8889 Email: [email protected]
1
Similar pages