bq24350 bq24352 www.ti.com ............................................................................................................................................................... SLUS943A – MAY 2009 – REVISED JUNE 2009 Over-Voltage and Over-Current Charger Front-end Protection IC With Integrated Charging FET FEATURES 1 • Robust Protection – Input Over-Voltage Protection – Input Over-Current Protection – Accurate Battery Over-Voltage Protection – Thermal Shutdown – Output Short-Circuit Protection • Integrated Charging FET • LDO Mode Operation • Current Limited Power Supply for Host Controller 2 • • • • • Soft-Start to Prevent Inrush Currents Soft-Stop to Prevent Voltage Spikes 30V Maximum Input Voltage Supports Up to 1A Load Current Small 2mm × 2mm 8pin SON Package APPLICATIONS • • Mobile Phones Low-Power Handheld Devices DESCRIPTION The bq24350/2 is a highly integrated circuit designed to provide protection to Li-ion batteries from failures of the charging circuit. The IC continuously monitors the input voltage and the battery voltage. In case of an input over-voltage condition, the IC will turn off the internal power FET after a blanking time. If the battery voltage rises to unsafe levels during charging process, power is removed from the system. If the input current exceeds the over current threshold for a limited time, the IC will turn off the output power. The integrated charging FET can regulate the charge voltage and current according to the control from the host. The device can also provide a voltage source with over voltage and over current protection for host controller. WHITE SPACE WHITE SPACE WHITE SPACE TYPICAL APPLICATION CIRCUIT PIN ASSIGNMENT WHITE SPACE WHITE SPACE bq24350 /2 ACIN BB CHG IN AC ACIN 1 8 OUT ACIN 2 7 OUT GND 3 6 CHGIN VBAT 4 5 GATDRV CHGIN CACIN CCHGIN Q1 1 mF 1 mF Q2 GATDRV GATDRV OUT ISENS 0 .2 W GND VBAT R BAT 200 kW VBAT PACK+ PACK- 1 2 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. PowerPAD is a trademark of Texas Instruments. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 2009, Texas Instruments Incorporated bq24350 bq24352 SLUS943A – MAY 2009 – REVISED JUNE 2009 ............................................................................................................................................................... www.ti.com These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. SIMPLIFIED FUNCTION BLOCK DIAGRAM Q2 Q1 VACIN ACIN V OUT OUT IIN Protection & Gate Control + - IO(OCP) INPUT UVLO VACIN + VUVLO - t BLK ( CHGIN ) VCHGIN + INPUT OVP GND VACIN + VOVP - - t DGL(OVP ) Control CHGIN VOREG 500 W L ogic VACIN + V OUT - V BAT + BVOVP - CHGIN Discharge SLEEP Battery OVP VBAT Protection Control t DGL (BOVP ) GATDRV Thermal Shutdown VBAT PIN FUNCTIONS PIN NAME NUMBER I/O ACIN 1,2 I Power Supply Input, connect to an external DC supply. Connect an external 1µF ceramic capacitor (minimum) to GND. OUT 7,8 O Output terminal to the charging system. VBAT 4 I Battery voltage sense input. Connected to pack positive terminal through a resistor. Connected to ground if battery OVP function is not used. GATDRV 5 I P-FET gate drive input , connected to gate drive pin of the host charger controller CHGIN 6 O Output power pin for power input of host charger controller. Connect an external ceramic bypass capacitor (1.0µF minimum) to GND. GND 3 – Ground terminal Thermal PAD DESCRIPTION There is an internal electrical connection between the exposed thermal pad and the GND pin of the device. The thermal pad must be connected to the same potential as the GND pin on the printed circuit board. Do not use the thermal pad as the primary ground input for the device. GND pin must be connected to ground at all times. ORDERING INFORMATION 2 PART NUMBER MARKING MEDIUM QUANTITY PACKAGE INPUT OVP THRESHOLD bq24350DSGR OAJ Tape and Reel 3000 2mm × 2mm SON 6.17 V bq24350DSGT OAJ Tape and Reel 250 2mm × 2mm SON 6.17 V bq24352DSGR OCY Tape and Reel 3000 2mm × 2mm SON 7.1 V bq24352DSGT OCY Tape and Reel 250 2mm × 2mm SON 7.1 V Submit Documentation Feedback Copyright © 2009, Texas Instruments Incorporated Product Folder Link(s): bq24350 bq24352 bq24350 bq24352 www.ti.com ............................................................................................................................................................... SLUS943A – MAY 2009 – REVISED JUNE 2009 ABSOLUTE MAXIMUM RATINGS (1) over operating free-air temperature range (unless otherwise noted) VALUE / UNIT Input voltage ACIN (with respect to GND) Output voltage OUT, CHGIN (with respect to GND) –0.3 V to 30 V Input voltage VBAT, GATDRV (with respect to GND) Input current ACIN –0.3 V to 7V –0.3 V to 7 V –1.8 A (2) to 1.4 A Junction temperature, TJ –40°C to 150°C Storage temperature, TSTG –65°C to 150°C (1) (2) Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under recommended operating conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. All voltage values are with respect to the network ground terminal unless otherwise noted. Reverse current is specified for a maximum of 50 hours at TJ < 150°C. PACKAGE DISSIPATION RATINGS PACKAGE PACKAGE DRAWING RθJC RθJA SON-8 DSG 5°C/W 75°C/W RECOMMENDED OPERATING CONDITIONS VACIN ACIN voltage range IACIN Current, ACIN pin TJ Junction Temperature MIN MAX 4.4 15 –40 Product Folder Link(s): bq24350 bq24352 V 1 A 125 °C Submit Documentation Feedback Copyright © 2009, Texas Instruments Incorporated UNITS 3 bq24350 bq24352 SLUS943A – MAY 2009 – REVISED JUNE 2009 ............................................................................................................................................................... www.ti.com ELECTRICAL CHARACTERISTICS Refer to the typical application circuit shown in Figure 1 . These specifications apply over ACIN=5V, TJ = -40~125°C, unless otherwise specified. Typical values are at TJ = 25°C. PARAMETER TEST CONDITIONS MIN TYP MAX ACIN: 3V → 2V, ACIN falling 1.8 1.95 2.1 ACIN: 2V → 3V, ACIN rising 2.5 UNIT ACIN VUVLO Under-voltage lock-out threshold tBLK(CHGIN) Input power on blanking time VACIN rising to CHGIN rising IDD Operating current No load on OUT and CHGIN pin 10 V ms 500 µA INPUT TO OUTPUT CHARACTERISTICS On resistance from ACIN to OUT IOUT = 1.0A, ACIN=5V, GATDRV=0V 415 685 mΩ On resistance from ACIN to CHGIN ICHGIN = 1.0A, ACIN=5V, IOUT=0A 250 495 mΩ 5.33 5.5 5.66 V INPUT OVER-VOLTAGE PROTECTION (OVP) VOREG ACIN=5.9V, GATDRV=CHGIN, ICHGIN=0 to 1A. CHGIN voltage in LDO mode Input OVP threshold, bq24350 VOVP VACIN rising Input OVP threshold, bq24352 Input OVP recovery hysteresis, bq24350 VHYS-OVP Input OVP recovery hysteresis, bq24352 VACIN: 7.5V → 5V 6 6.17 6.35 6.9 7.1 7.3 250 300 350 100 150 200 V mV tDGL(OVP) Input OVP deglitch time VACIN rising to CHGIN falling 256 µS tREC(OVP) Input OVP recovery time VACIN falling below VOVP to CHGIN rising 8.2 ms INPUT OVER CURRENT LIMITING AND PROTECTION (OCP) IO(OCP) OCP threshold 1.02 1.2 1.38 A tDGL(OCP) OCP blanking time 8.2 ms tREC(OCP) OCP recovery time 131 ms BATTERY OVER-VOLTAGE PROTECTION BVOVP Battery OVP threshold VBAT rising 4.3 4.35 4.4 V VHYS-BOVP Battery OVP hysteresis VBAT falling 200 250 300 mV IVBAT VBAT pin leakage current VBAT=4.25V, series connection of a 200kΩ resistor, TJ = 25°C 10 nA tDGL(BOVP) Battery OVP deglitch time VBAT rising to CHGIN falling 8.2 ms tREC(BOVP) Battery OVP recovery time VBAT falling below BVOVP to CHGIN rising 131 ms VSEXIT Sleep mode exit threshold and CHGIN turn on threshold, ACIN-VOUT ACIN rising, VOUT = 4.2 V 24 90 160 mV VSENTRY Sleep mode entry threshold and CHGIN turn off threshold, ACIN-VOUT ACIN falling, VOUT = 4.2 V 10 55 105 mV IDDSLP Sleep Mode supply current OUT = 4.2 V, GATDRV = 4.2 V, ACIN = VSS 10 µA RDIS CHGIN discharge resistor CHGIN Ω 500 Leakage current from OUT to CHGIN OUT = 4.2 V, GATDRV = 4.2 V, CHGIN = 0 V, ACIN = 0 V, TJ = 85°C 1 µA 680 800 mV 0.1 1 µA INTEGRATED P-FET PARAMETERS Vt Threshold Voltage, CHGIN-GATDRV. CHGIN=5V, OUT=3.6V, IOUT=10mA 500 Ig GATDRV pin leakage current Ioff Off state leakage current at OUT pin. ACIN=5V, GATDRV=CHGIN, OUT=0V Ronp On Resistance of P-FET (from CHGIN to OUT) IOUT = 1.0A, ACIN=5V, GATDRV=0V Gm Forward Transconductance ACIN=5V, IOUT=5mA, GATDRV=3.5V Cg Input capacitance at the GATDRV pin CHGIN=GATDRV=5V µA 1 165 225 mΩ 27 mA/V 104 pF THERMAL PROTECTION 4 Submit Documentation Feedback Copyright © 2009, Texas Instruments Incorporated Product Folder Link(s): bq24350 bq24352 bq24350 bq24352 www.ti.com ............................................................................................................................................................... SLUS943A – MAY 2009 – REVISED JUNE 2009 ELECTRICAL CHARACTERISTICS (continued) Refer to the typical application circuit shown in Figure 1 . These specifications apply over ACIN=5V, TJ = -40~125°C, unless otherwise specified. Typical values are at TJ = 25°C. PARAMETER TJ(OFF) TEST CONDITIONS Thermal shutdown threshold Junction temperature rising TJ(OFF-HYS) Thermal shutdown hysteresis MIN TYP MAX UNIT 140 150 160 °C Junction temperature falling 20 °C TYPICAL APPLICATION CIRCUIT ACIN=5V, ICHARGE=1A, VBAT=4.2V bq24350/2 ACIN BB CHGIN AC CHGIN CACIN CCHGIN Q1 1 mF 1 mF GATDRV Q2 GATDRV OUT ISENS 0.2 W GND VBAT R BAT VBAT 200 kW PACK+ PACK- Figure 1. Host Controlled One-Cell Charger Application Circuit TYPICAL PERFORMANCE CHARACTERISTICS Using circuit shown in typical application circuit Figure 1, TA = 25°C, unless otherwise specified. ACIN RAMP UP ACIN RAMP DOWN GATDRV 2 V/div ACIN 2 V/div CHGIN Pull Down CHGIN 2 V/div ACIN 2 V/div Soft-Start Soft-Stop VACIN = 5.2 V, CHGIN = 4.5 V, ICHG = 0.6 A, VGATDRV = 3.5 V, VBAT = 3.4 V CHGIN 2 V/div IACIN 0.5 A/div IACIN 0.5 A/div VACIN = 5.2 V, CHGIN = 4.5 V, ICHG = 0.6 A, VGATDRV = 3.5 V, VBAT = 3.4 V Time: 2 mS/div Time: 1 mS/div Figure 2. Figure 3. Submit Documentation Feedback Copyright © 2009, Texas Instruments Incorporated Product Folder Link(s): bq24350 bq24352 5 bq24350 bq24352 SLUS943A – MAY 2009 – REVISED JUNE 2009 ............................................................................................................................................................... www.ti.com TYPICAL PERFORMANCE CHARACTERISTICS (continued) ACIN OVP (BLANKING TIME) 16 V ACIN OVP 16 V ACIN 5 V/div ACIN 5 V/div CHGIN 1 V/div 5V CHGIN 1 V/div 5V 6V 5.5 V VACIN = 5-16 V, Rising Time 0.5 ms VACIN = 5-16 V, Rising Time 0.5 ms ICHGIN 0.1 A/div ICHGIN 0.1 A/div Time: 1 ms/div Time: 100 ms/div Figure 4. Figure 5. ACIN OVP CHGIN OCP ACIN 5 V/div VACIN = 5 V, ICHGIN = 0 to 1.3 A VACIN = 5-16 V, Rising Time 0.5 ms, ICHGIN 2V/div CHGIN 2 V/div CHGIN 2 V/div 1.3 A ICHGIN 0.5 A/div ICHGIN 0.1 A/div Time: 20 mS/div Time: 100 mS/div Figure 6. Figure 7. CHGIN OCP BATTERY OVP VBAT 2 V/div Connect 3 W Load CHGIN 2 V/div VACIN = 5 V, ICHGIN = 0 to1.3 A VACIN = 5 V, VBAT = 3.4 V to 5 V ICHGIN 0.5 A/div CHGIN 2 V/div ICHGIN 0.1 A/div Time: 2 mS/div Time: 50 mS/div Figure 8. 6 Figure 9. Submit Documentation Feedback Copyright © 2009, Texas Instruments Incorporated Product Folder Link(s): bq24350 bq24352 bq24350 bq24352 www.ti.com ............................................................................................................................................................... SLUS943A – MAY 2009 – REVISED JUNE 2009 TYPICAL PERFORMANCE CHARACTERISTICS (continued) Rdson vs Vgs rdson - Static Drain-Source On-State Resistance - W BATTERY OVP VBAT 2 V/div VACIN = 5 V, VBAT = 3.4 V to 5 V CHGIN 2 V/div IACIN 0.5 A/div Time: 2 mS/div 10000 1000 VCHGIN = 5 V, VCHGIN -VOUT = 200 mV 100 10 Q2 1 0.1 0 1000 2000 3000 Vgs - Vchgin-Vgatdrv - mV Figure 10. 4000 5000 Figure 11. rdson - Static Drain-Source On-State Resistance - mW FET ON RESISTANCE vs TEMPERATURE 600 550 500 Q1 +Q2 450 400 350 Q1 300 250 Q2 200 150 100 -50 0 50 100 TJ - Junction Temperature - °C 150 Figure 12. BACKGROUND During the charging process for portable devices, input voltage spikes usually happen when the AC/DC adaptor is plugged in, or charge current is cut off quickly under fault conditions, such as input OVP, OCP or battery OVP and so on. The over voltage stress may damage the analog baseband chip which has lower voltage rating due to its increased complexity. Therefore, over voltage protection is needed for the safe operation of portable devices. Another challenge arises from the charge circuit that uses external charging FET in series with a reverse blocking diode as the charging device. The battery may not be fully charged when input voltage is low due to the additional diode voltage drop. bq24350/2 will provide the solution for above problems since it has input OVP, OCP, battery OVP function, together with integrated charging FET which will eliminate the reverse blocking diode in the previously mentioned charge circuit, as shown in Figure 1. DETAILED FUNCTIONAL DESCRIPTION The bq24350/2 is a highly integrated circuit designed to provide protection to Li-ion batteries from failures of the charging circuit. The IC continuously monitors the input voltage and the battery voltage. In case of an input over-voltage condition, the IC will turn off the internal power FET after a blanking time. If the battery voltage rises to unsafe levels during charging process, power is removed from the system. If the input current exceeds the over current threshold for a limited time, the IC will turn off the output power. The integrated charging FET can regulate the charge voltage and current according to the control from the host. The device can also provide a voltage source with over voltage and over current protection for host controller. Submit Documentation Feedback Copyright © 2009, Texas Instruments Incorporated Product Folder Link(s): bq24350 bq24352 7 bq24350 bq24352 SLUS943A – MAY 2009 – REVISED JUNE 2009 ............................................................................................................................................................... www.ti.com POWER DOWN The device remains in power down mode when the input voltage at the ACIN pin is below the under-voltage threshold VUVLO. The FET Q1 and Q2 connected between ACIN and OUT pins are off. POWER-ON RESET The device resets when the input voltage at the ACIN pin exceeds the UVLO threshold. All internal counters and other circuit blocks are reset. The IC then waits for duration tBLK(CHGIN) for the input voltage to stabilize. If, after tBLK(CHGIN), the input voltage and battery voltage are in normal range, FET Q1 is turned ON. The IC has a soft-start feature to control the inrush current. The soft-start minimizes the ringing at the input, where the ringing occurs because the parasitic inductance of the adapter cable and the input bypass capacitor form a resonant circuit. Once the soft-start sequence starts, the IC monitors the load current. If the load current is larger than IO(OCP) for more than tDGL(OCP), FET Q1 and Q2 are switched off. The IC then repeats the power-on sequence after tREC(OCP). When a short-circuit is detected at power-on and Q1 is switched off, to prevent the input voltage from spiking up due to resonance between the inductance of the input cable and the input capacitor, Q1 is turned off slowly by reducing its gate-drive gradually, resulting in a “soft-stop”. SLEEP MODE When ACIN falls to below sleep mode entry threshold (VSENTRY), the device operates in sleep mode and turns off Q1 and Q2 by internal circuit regardless of the gate drive signal from GARDRV pin. The device exits sleep mode when ACIN rising to above sleep mode exit threshold (VSEXIT). In this way, the device behaves like a diode and no external reverse blocking diode is needed in the application circuit. OPERATING The device continuously monitors the input voltage, the input current and the battery voltage as described in detail below: Input Over-Voltage Protection and LDO Mode Operation The CHGIN output of the IC operates similar to a linear regulator. Figure 13 shows the typical input OVP performance. When the ACIN input voltage is less than VO(REG), and above the VUVLO, the CHGIN output voltage tracks the input voltage with a voltage drop caused by RDS(on) of the protection FET Q1. When the ACIN input voltage is greater than VO(REG) plus the RDS(on) drop of Q1, and less than VOVP, the CHGIN output voltage is regulated to VO(REG), and this is also referred as LDO mode operation. If the input voltage rises above VOVP, the internal FET Q1 and Q2 are turned off after a blanking time of tDGL(OVP), removing power from the circuit. When the input voltage drops below VOVP – VHYS-OVP, and is still above VUVLO, the FET Q1 and Q2 are turned on again after a deglitch time of tREC(OVP) , which ensures that the input supply is stabilized when the IC starts up again. VIN<VOREG ACIN VIN>VOREG VOVP VPOR VO(REG) CHGIN tDGL(OVP) tREC(OVP) tBLK(CHGIN) ACIN OVP Figure 13. Input OVP Timing Diagram Over Current Limiting and Protection The device includes a low drop out linear current regulator. This current regulator uses Q1 as the controlling 8 Submit Documentation Feedback Copyright © 2009, Texas Instruments Incorporated Product Folder Link(s): bq24350 bq24352 bq24350 bq24352 www.ti.com ............................................................................................................................................................... SLUS943A – MAY 2009 – REVISED JUNE 2009 power device. Once the soft start sequence starts, the input current is limited to the Over Current Protection (OCP) threshold, IO(OCP). If the input current through the IC attempts to exceed the OCP threshold, the switch Q1 is opened only enough to maintain the current at the OCP level. If the current limiting condition is maintained longer than the deglitch time, tDGL(OCP), both the switch Q1 and Q2 are opened completely, as shown in Figure 14. In this fault case, the switch Q1 is turned off slowly, typically taking 100µS. Once the OCP feature has been activated, the switch Q1 and Q2 will remain off for the OCP recovery time, tREC(OCP). Following this time the switch will turn on, using soft start sequence. If the current through the IC remains below the OCP threshold, the switch will remain closed and normal operation resumes. If the current through the IC attempts to exceed the OCP threshold again, the operation described above repeats. IACIN OCP T hreshold CHGIN tDGL(OCP) tREC(OCP) tREC(OCP) tDGL(OCP) Figure 14. Charge Current OCP Timing Diagram Battery Over-Voltage Protection The battery over-voltage threshold, BVOVP, is internally set to 4.35V. If the battery voltage exceeds the BVOVP threshold, the FET Q1 and Q2 are turned off after a deglitch time of tDGL(BOVP). The FET is turned on once the battery voltage drops to BVOVP – VHYS-BOVP and remains below this threshold for tREC(BOVP), as shown in Figure 15. In this battery over-voltage fault case, Q1 is switched OFF gradually for a smooth transient response. VBAT VBAT OVP CHGIN tDGL(BOVP) tREC(BOVP) tDGL(BOVP) tREC(BOVP) Figure 15. Battery OVP Timing Diagram Thermal Protection If the junction temperature of the device exceeds TJ(OFF), the FET Q1 and Q2 are turned off. The FET is turned back on when the junction temperature falls below TJ(OFF) – TJ(OFF-HYS). Submit Documentation Feedback Copyright © 2009, Texas Instruments Incorporated Product Folder Link(s): bq24350 bq24352 9 bq24350 bq24352 SLUS943A – MAY 2009 – REVISED JUNE 2009 ............................................................................................................................................................... www.ti.com APPLICATION INFORMATION Selection of RBAT It is strongly recommended that the battery not be tied directly to the VBAT pin of the device, as under some failure modes of the IC, the voltage at the ACIN pin may appear on the VBAT pin. This voltage can be as high as 30V, and applying 30V to the battery in case of the failure of the device can be hazardous. Connecting the VBAT pin through RBAT prevents a large current from flowing into the battery in case of failure of the IC. In the interests of safety, RBAT should have a very high value. The problem with a large RBAT is that the voltage drop across this resistor because of the VBAT bias current IVBAT causes an error in the BVOVP threshold. This error is over and above the tolerance on the nominal 4.35V BVOVP threshold. Choosing RBAT in the range 100kΩ to 470kΩ is a good compromise. In the case of IC failure, with RBAT equal to 100kΩ, the maximum current flowing into the battery would be (30V – 3V) ÷ 100kΩ = 270µA, which is low enough to be absorbed by the bias currents of the system components. RBAT equal to 100kΩ would result in a worst-case voltage drop of RBAT × IVBAT ≈ 1mV. This is negligible compared to the internal tolerance of 50mV on the BVOVP threshold. If the Battery OVP function is not required, the VBAT pin should be connected to GND. Selection of Input and Output Bypass Capacitors The input capacitor CACIN is for decoupling, and serves an important purpose. Whenever there is a step change downwards in the system load current, the inductance of the input cable causes the input voltage to spike up. CACIN prevents the input voltage from overshooting to dangerous levels. It is strongly recommended that a ceramic capacitor of at least 1µF be used at the input of the device. It should be located in close proximity to the ACIN pin. CCHGIN should also be a ceramic capacitor of at least 1µF, located close to the CHGIN pin. CCHGIN also serves as the input decoupling capacitor for the charging circuit downstream of the protection IC. PCB Layout Guidelines 1. This device is a protection device, and is meant to protect down-stream circuitry from hazardous voltages. Potentially, high voltages may be applied to this IC. It has to be ensured that the edge-to-edge clearances of PCB traces satisfy the design rules for the maximum voltages expected to be seen in the system. 2. The device uses SON packages with a PowerPAD™. For good thermal performance, the PowerPAD should be thermally coupled with the PCB ground plane. In most applications, this will require a copper pad directly under the IC. This copper pad should be connected to the ground plane with an array of thermal vias. 3. CACIN and CCHGIN should be located close to the IC. Other components like RBAT should also be located close to the IC. 10 Submit Documentation Feedback Copyright © 2009, Texas Instruments Incorporated Product Folder Link(s): bq24350 bq24352 PACKAGE OPTION ADDENDUM www.ti.com 5-Jun-2009 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty BQ24350DSGR ACTIVE SON DSG 8 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR BQ24350DSGT ACTIVE SON DSG 8 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR BQ24352DSGR ACTIVE SON DSG 8 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR BQ24352DSGT ACTIVE SON DSG 8 250 CU NIPDAU Level-2-260C-1 YEAR Green (RoHS & no Sb/Br) Lead/Ball Finish MSL Peak Temp (3) (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 5-Jun-2009 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing BQ24350DSGR SON DSG 8 SPQ Reel Reel Diameter Width (mm) W1 (mm) A0 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant 3000 179.0 8.4 2.2 2.2 1.2 4.0 8.0 Q2 BQ24350DSGT SON DSG 8 250 179.0 8.4 2.2 2.2 1.2 4.0 8.0 Q2 BQ24352DSGR SON DSG 8 3000 179.0 8.4 2.2 2.2 1.2 4.0 8.0 Q2 BQ24352DSGT SON DSG 8 250 179.0 8.4 2.2 2.2 1.2 4.0 8.0 Q2 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 5-Jun-2009 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) BQ24350DSGR SON DSG 8 3000 195.0 200.0 45.0 BQ24350DSGT SON DSG 8 250 195.0 200.0 45.0 BQ24352DSGR SON DSG 8 3000 195.0 200.0 45.0 BQ24352DSGT SON DSG 8 250 195.0 200.0 45.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Amplifiers Data Converters DLP® Products DSP Clocks and Timers Interface Logic Power Mgmt Microcontrollers RFID RF/IF and ZigBee® Solutions amplifier.ti.com dataconverter.ti.com www.dlp.com dsp.ti.com www.ti.com/clocks interface.ti.com logic.ti.com power.ti.com microcontroller.ti.com www.ti-rfid.com www.ti.com/lprf Applications Audio Automotive Broadband Digital Control Medical Military Optical Networking Security Telephony Video & Imaging Wireless www.ti.com/audio www.ti.com/automotive www.ti.com/broadband www.ti.com/digitalcontrol www.ti.com/medical www.ti.com/military www.ti.com/opticalnetwork www.ti.com/security www.ti.com/telephony www.ti.com/video www.ti.com/wireless Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2009, Texas Instruments Incorporated