AZ2150W 30 AMP MINIATURE POWER RELAY RoHS compliant ! FEATURES • • • • • • • • 1.75 mm contact gap DC coils up to 48V High dielectric strength 4 kV contact to coil All plastics PTI 250 Epoxy sealed versions available UL Class F (155°C) standard UL, CUR file E44211 VDE certificate 40023154 CONTACTS GENERAL DATA Arrangement SPST (1 Form A) Ratings Resistive load: Ratings UL, CUR VDE Life Expectancy Mechanical Electrical Minimum operations 2 x 105 3 x 104 at 30 A 250 VAC Res. Max. switched power: 900 W or 8310 VA Max. switched current: 30 A Max. switched voltage: 250 VDC* or 440 VAC Operate Time 15 ms max. at nominal coil voltage Release Time 10 ms max. at nominal coil voltage (with no coil suppression) *Note: If switching voltage is greater than 30 VDC, special precautions must be taken. Please contact the factory. Dielectric Strength (at sea level for 1 min.) 3000 Vrms between open contacts 4000 Vrms contact to coil Insulation Resistance 1000 megaohms min. at 20°C, 500 VDC 50% RH Insulation (according to DIN VDE 0110, IEC 60664-1) C250 Overvoltage category: III Pollution degree: 2 Nominal voltage: 250 VAC Holding Voltage Greater than 50% of nominal coil voltage Dropout Greater than 10% of nominal coil voltage Ambient Temperature Operating -40°C (-40°F) to 85°C (185°F) Vibration 1.5 mm DA at 10-55 Hz Shock 10 g Enclosure P.B.T. polyester 30 A at 277 VAC, General use 20 A at 250 VAC, AC7a Material Silver tin oxide Resistance < 50 milliohm initially (24 V, 1A voltage drop method) COIL Power At Pickup Voltage (typical) 625 mW Max. Continuous Dissipation 1.7 W at 20°C (68°F) ambient Temperature Rise 43°C (77°F) at nominal coil voltage Terminals Tinned copper alloy, P.C. 155°C (311°F) Class F Max. Solder Temp. 270°C (518°F) Max. Solder Time 5 seconds Max. Solvent Temp. 80°C (176°F) 1. All values at 20°C (68°F). Max. Immersion Time 30 seconds 2. Relay may pull in with less than “Must Operate” value. Weight 25 grams 3. Specifications subject to change without notice. Packing unit in pcs 40 per plastic tray / 280 per carton Max. Temperature NOTES 4. If higher electrical loads are to be switched by the relay contacts, the vent nib has to be opened prior to use of the relay. ZETTLER electronics GmbH Junkersstr. 3, D-82178 Puchheim, Germany - A ZETTLER GROUP Company phone: +49 89 800 97-0 [email protected] fax: +49 89 800 97-200 www.ZETTLERelectronics.com This product specification to be used only together with the application notes which can be downloaded from http://www.ZETTLERelectronics.com/pdfs/relais/ApplicationNotes.pdf 2015-03-31 AZ2150W RELAY ORDERING DATA COIL SPECIFICATIONS – DC Coil Nominal Coil VDC 5 Must Operate VDC 3.75 Min. Holding VDC 2.5 Max. Continuous VDC 6.0 6 4.50 3.0 7.2 9 6.75 4.5 10.8 ORDER NUMBER* Coil Resistance Ohm ± 10% 22.5 AZ2150W–1AE–5DFT 32.5 AZ2150W–1AE–6DFT 73 AZ2150W–1AE–9DFT 12 9.0 6.0 14.4 130 AZ2150W–1AE–12DFT 24 18.0 12.0 38.8 520 AZ2150W–1AE–24DFT 48 36.0 24.0 57.6 2,080 AZ2150W–1AE–48DFT * Substitute “DEFT” in place of “DFT” for epoxy sealed version. Coils 5VDC, 6VDC, 48VDC not VDE approved. MECHANICAL DATA PC BOARD LAYOUT .500 .400 (12.8) (10.2) Vent nib. (Please pay attention to note 4 on page 1.) 2 x ø .079 (ø 2.0) .020 .130 +– .010 + 0.51) (3.3 – 0.25 1.25 (31.80) .090 (2.3) 1.000 (25.4) .500 (12.7) .690 (17.5) 2 x ø .044 (ø 1.1) 1.06 (26.9) .196 (5.0) .150 (3.8) .751 (19.1) .550 (14.0) .700 (17.8) Viewed toward terminals WIRING DIAGRAM .200 (5.1) .045 x .045 (1.14 x 1.14) .032 x .062 (0.81 x 1.57) 1 FORM A (SPST-NO) .025 x .025 (0.63 x 0.63) Viewed toward terminals Dimensions in inches with metric equivalents in parentheses. Tolerance: ± .010" ZETTLER electronics GmbH Junkersstr. 3, D-82178 Puchheim, Germany - A ZETTLER GROUP Company phone: +49 89 800 97-0 [email protected] fax: +49 89 800 97-200 www.ZETTLERelectronics.com This product specification to be used only together with the application notes which can be downloaded from http://www.ZETTLERelectronics.com/pdfs/relais/ApplicationNotes.pdf 2015-03-31 AZ2150W Electrical life at 250 VAC, resistive load Electrical life reduction factor at inductive AC load 107 F 1,0 Reduction factor Number of cycles 0,9 106 0,8 0,7 0,6 0,5 105 0,4 0,3 1,0 0,9 0,8 0,7 0,6 0,5 0,4 0,3 cos j 0,2 Power factor 104 0 0,8 1,6 2,4 3,2 4,0 4,8 5,6 6,4 7,2 Ncos j = N x F 8,0 Breaking capacity [kVA] Max. AC/DC resistive load breaking capacity 50 AC Current [A] 30 10 5 2 DC 1 0,5 0,1 10 20 30 40 50 100 200 400 600 Voltage [V] ZETTLER electronics GmbH Junkersstr. 3, D-82178 Puchheim, Germany - A ZETTLER GROUP Company phone: +49 89 800 97-0 [email protected] fax: +49 89 800 97-200 www.ZETTLERelectronics.com This product specification to be used only together with the application notes which can be downloaded from http://www.ZETTLERelectronics.com/pdfs/relais/ApplicationNotes.pdf 2015-03-31