ETC AZ733-2C-6D Dpdt miniature power relay Datasheet

AZ733
DPDT MINIATURE
POWER RELAY
FEATURES
•
•
•
•
•
•
•
•
Dielectric strength 5000 Vrms
Low cost
Epoxy sealed version available
10 Amp switching — double pole contacts
Isolation spacing greater than 8mm
UL Class B insulation system
UL, CUR file E44211
TÜV file R9659062
GENERAL DATA
CONTACTS
Arrangement
DPST (2 Form A)
DPDT (2 Form C)
Ratings
Resistive load:
Max. switched power: 300 W or 2500 VA
Max. switched current: 10 A
Max. switched voltage: 150* VDC or 380 VAC
*Note: If switching voltage is greater than 30 VDC, special
precautions must be taken. Please contact the factory.
Rated Load
TÜV
10 A at 250 VAC General Use, 100k cycles[1][2][3]
10 A at 30 VDC N.O. Resistive 100k cycles [1]
10 A at 30 VDC N.C. Resistive 50k cycles [1]
10 A at 30 VDC N.O./N.C. Resistive 25k cycles[2][3]
1/4 HP at 240 VAC [1]
1/8 HP at 120 VAC [1]
TV-3 at 125 VAC (2 Form A) [1]
5 A at 30 VDC, 250 VAC resistive, 100k cycles
[1][2][3]
[1] Silver cadmium oxide [2] Silver tin oxide [3] Silver
nickel
Material
Silver cadmium oxide, silver tin oxide or silver nickel,
gold plating available
Resistance
< 50 milliohms initially
(24 V, 1 A voltage drop method)
COIL
Power
At Pickup Voltage
(typical)
257 mW
Max. Continuous
Dissipation
1.9 W at 20°C (68°F) ambient
Temperature Rise
34°C (61°F) at nominal coil voltage
Temperature
Max. 130°C (266°F)
Life Expectancy
Mechanical
Electrical
Minimum operations
1 x 107
1 x 105 at 10 A 240 VAC Res.
Operate Time (typical)
8 ms at nominal coil voltage
Release Time (typical)
5 ms at nominal coil voltage
(with no coil suppression)
Dielectric Strength
5000 Vrms contact to coil
(at sea level for 1 min.) 1000 Vrms between open contacts
3000 Vrms between contact sets
Insulation
Resistance
1000 megohms min. at 20°C, 500 VDC,
50% RH
Dropout
Greater than 10% of nominal coil voltage
Ambient Temperature
Operating
Storage
-40°C (-40°F) to 90°C (194°F)
-40°C (-40°F) to 130°C (266°F)
Vibration
0.062" DA at 10–55 Hz
Shock
10 g
Enclosure
P.B.T. polyester
Terminals
Tinned copper alloy, P.C.
Max. Solder Temp.
270°C (518°F)
Max. Solder Time
5 seconds
Max. Solvent Temp.
80°C (176°F)
Max. Immersion Time
30 seconds
Weight
18 grams
NOTES
1. All values at 20°C (68°F).
2. Relay may pull in with less than “Must Operate” value.
3. Specifications subject to change without notice.
09/14/04W
AZ733
RELAY ORDERING DATA
COIL SPECIFICATIONS
ORDER NUMBER*
Nominal Coil
VDC
3
Must Operate
VDC
2.1
Max. Continuous
VDC
5.7
5
6
9
12
18
24
48
60
110**
3.5
4.2
6.3
8.4
12.6
16.8
33.6
42.0
79.3
9.4
11.4
17.4
22.8
27.9
45.7
89.0
115.3
170.5
Coil
Resistance
17 ±10%
47
68
160
275
650
1100
4170
7000
22900
±10%
±10%
±10%
±10%
±10%
±15%
±15%
±15%
±15%
Form A
(DPST)
AZ733–2A–3D
Form C
(DPDT)
AZ733–2C–3D
AZ733–2A–5D
AZ733–2A–6D
AZ733–2A–9D
AZ733–2A–12D
AZ733–2A–18D
AZ733–2A–24D
AZ733–2A–48D
AZ733–2A–60D
AZ733–2A–110D
AZ733–2C–5D
AZ733–2C–6D
AZ733–2C–9D
AZ733–2C–12D
AZ733–2C–18D
AZ733–2C–24D
AZ733–2C–48D
AZ733–2C–60D
AZ733–2C–110D
*Add suffix “E” to “2A” or “2C” for silver tin oxide contacts. Add suffix “B” to “2A” or “2C” for silver nickel contacts. Add suffix”E” for epoxy sealed version. Add
suffix “A” for gold plated contacts. **110 v Coil not TÜV approved.
HARDWARE ORDERING DATA
DESCRIPTION
ORDER NUMBER
DESCRIPTION
ORDER NUMBER
Socket
ST484–U1
Retainer
ST482–2
MECHANICAL DATA
PC BOARD LAYOUT
Form A and C
Viewed toward terminals
.51
(13)
.590
(15)
.197 .197
(5) (5)
.295 (7.5)
0.015
(0.38)
1.02
(25.9)
.160 ± .015
(4.2 ± .4)
1.14
(29)
.08
(2.1)
.05 DIA. (1.3)
(Form C only)
HARDWARE
.500
(12.7)
ST484-U1
Terminal No. Dimensions Tol.: ± 0.005 (0.13)
1,2,4,5,7,8 0.018 (0.457) x 0.038 (0.965)
3,6
0.011 (0.279) x 0.038 (0.965)
(6 places Form A)
(8 places Form C)
.177
(4.5)
MAX
1.28
(32.5)
1.22
(30.9)
.414
(10.5)
.125 DIA
(0.5)
WIRING DIAGRAM
Form A
.366
(9.3)
Retaining Clip
Form C
.295
(7.5)
1
3
4
1
2
3
4
8
6
5
8
7
6
5
Viewed toward terminals
.197
(5.0)
.197
(5.0)
.590 (15)
.118
(3.0)
.354
(9.0)
.059 DIA
(1.5)
Viewed toward terminals
1.217
(30.9)
ST482-2
.158
(4.0)
1.044
(26.5)
.138 (3.5)
Dimensions in inches with metric equivalents in parentheses. Tolerance: ± .010"
09/14/04W
Similar pages