155 Mbps Bi-directional Receptacle Single Fiber Transceiver B-15/13-155(C)-TDFB(3)-Sxx5(7) Features • Diplexer Single Mode Single Fiber 1x9 SC/FC/ST Receptacle Connector • Wavelength Tx 1550 nm/Rx 1310 nm • SONET OC-3 SDH STM-1 Compliant • Single +5V power Supply • Single +3.3V power Supply • PECL/LVPECL Differential Inputs and Outputs [B-15/13-155-TDFB(3)-Sxx5(7)] • TTL/LVTTL Differential Inputs and Outputs [B-15/13-155C-TDFB(3)-Sxx5(7)] • Wave Solderable and Aqueous Washable • LED Multisourced 1x9 Transceiver Interchangeable • Class 1 Laser Int. Safety Standard IEC 825 Compliant • Uncooled Laser diode with MQW structure DFB Laser • Complies with Telcordia (Bellcore) GR-468-CORE • RoHS compliant Absolute Maximum Rating Parameter Symbol Min. Max. Unit Vcc 0 6 V B-15/13-155-TDFB-Sxx5(7) Power Supply Voltage Vcc 0 3.6 V B-15/13-155-TDFB3-Sxx5(7) Output Current Iout - 30 mA - - 260 ºC Tstg -40 85 ºC Symbol Min. Typ. Max. Unit Vcc 4.75 5 5.25 V Power Supply Voltage Vcc 3.1 3.3 3.5 V Operating Temperature (Case) Topr 0 - 70 ºC - - 155 - Mbps Power Supply Voltage Soldering Temperature Storage Temperature Note 10 seconds on leads only Recommended Operating Condition Parameter Power Supply Voltage Data Rate Transmitter Specifications Parameter Symbol Min Typical Max Unit Notes Optical Transmit Power Po -5 - 0 dBm Output power is coupled into a 9/125 µm single mode fiber (B-15/13-155-TDFB(3)-Sxx5) Optical Transmit Power Po -3 - +2 dBm Output power is coupled into a 9/125 µm single mode fiber (B-15/13-155-TDFB(3)-Sxx7) Output center Wavelength λ 1480 1550 1580 nm Optical Output Spectrumt Width ∆λ - - 1 nm -20dB width Side Mode Suppression Ratio Sr 30 35 - dB CW Extinction Ratio ER 10 - - dB Output Eye Compliant with ITU-T recommendation G.957/STM-1 Optical Rise Time tr - - 2 ns 10% to 90% Values Optical Fall Time tf - - 2 ns 10% to 90% Values Optical Isolation - 30 - - dB Isolation potential between 1480-1580nm at least 30dB RIN - - -116 dB/Hz TJ - - 1.2 ns Relative Intensity Noise Total Jitter LUMINENTOIC.COM Measured with 223-1 PRBS with 72 ones and 72 zeros. 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 1 LUMNDS581-Apr2107 Rev A.3 155 Mbps Bi-directional Receptacle Single Fiber Transceiver B-15/13-155(C)-TDFB(3)-Sxx5(7) Transmitter Specifications Parameter Symbol Min Typical Max Unit Power Supply Current ICC - - 200 mA Data Input Current-Low IIL -350 - - µA Notes Electrical Data Input Current-High IIH - - 350 µA Differential Input Voltage VIH-VIL 300 - - mV Data Input Voltage-Low VIL-VCC -2.0 - -1.58 V Data Input Voltage-High VIH-VCC -1.1 - -0.74 V Symbol Min Typical Max Unit Sensitivity - - - -33 dBm Sensitivity - - - -35 dBm Maximum Input Power Pin -3 - - dBm Signal Detect-Asserted (Note 1) Pa - - -33 dBm Signal Detect-Asserted (Note 2) Pa - - -35 dBm Signal Detect-Deasserted Pd -45 - - dBm 1.0 - 4.0 dB 1260 - 1360 nm Maximum current is specified at Vcc= Maximum @ maximum temperature These inputs are compatible with 10K, 10KH and 100K ECL and PECL inputs Receiver Specifications Parameter Optical Signal Detect-Hysteresis Wavelength of Operation Notes Measured with 223-1 PRBS, BER = 10-10, B-15/13-155-TDFB(3)-SSC5 Measured with 223-1 PRBS, BER = 10-10, B-15/13-155-TDFB(3)-SSC7 MEasured on transition : low to high B-15/13-155-TDFB(3)-SSC5 MEasured on transition : low to high B-15/13-155-TDFB(3)-SSC7 Measured on transition: high to low Note 1: Regardless of whether the Tx is on or not, SD should be asserted at less than -33 dBm of input power leve. Note 2: Regardless of whether the Tx is on or not, SD should be asserted at less than -35 dBm of input power level. Receiver Specifications Parameter Symbol Min Typical Max Unit Note ICC - - 100 mA The current excludes the output load current Electrical Power Supply Current Data Output Voltage-Low VOL -Vcc -2.0 - -1.58 V Data Output Voltage-High VOH- Vcc -1.1 - -0.74 V Signal Detect Output Voltage-Low VSDL-Vcc -2.0 - -1.58 V Signal Detect Output Voltage-High VSDH- Vcc -1.1 - -0.74 V LUMINENTOIC.COM These outputs are compatible with 10K, 10KH and 100KECL and PECL outputs 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 2 LUMNDS581-Apr2107 Rev A.3 155 Mbps Bi-directional Receptacle Single Fiber Transceiver B-15/13-155(C)-TDFB(3)-Sxx5(7) Connection Diagram 1. (Rx GND) 2. (Rx +) 3. (Rx-) 4. (SD) 5. (Rx Vcc) 6. (Tx Vcc) 7. (TX-) 8. (TX+) 9. (Tx GND) NC Top View NC Receiver Signal Ground Receiver Data Out Receiver Data Out Bar Signal Detect Receiver Power Supply Transmitter Power Supply Transmitter Data In Bar Transmitter Data in Transmitter Signal Ground PIN Symbol Notes 1 RxGND Directly connect this pin to the receiver ground plane 2 RD+ See recommended circuit schematic 3 RD- See recommended circuit schematic 4 SD 5 RxVcc DC power for the receiver section 6 TxVcc DC power for the transmitter section 7 TD- See recommended circuit schematic 8 Warnings TD+ See recommended circuit schematic 9 LUMINENTOIC.COM Active high on this indicates a received optical signal TxGND Directly connect this pin to the transmitter ground plane 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 3 LUMNDS581-Apr2107 Rev A.3 155 Mbps Bi-directional Receptacle Single Fiber Transceiver B-15/13-155(C)-TDFB(3)-Sxx5(7) Recommended Circuit Schematic (3.3V/5V) B-15/13-155-TDFB(3)-Sxx5(7) Tx Vcc C5 Rx Vcc 9 R1 7 8 6 5 4 3 2 1 R3 R9 R5 C6 R7 TD + RD + TD - RD - Tx Vcc SD Rx Vcc R2 R4 Notes +3.3V: R1=R3=R5=R7=R9=130 R2=R4=R6=R8=R10=82 C1=C2=C3=C5=C6=0.1F C4=10F L1=L2=1H No internal connection Transceiver Top view No internal connection R10 R6 R8 L1 Notes +5V: R1=R3=R5=R7=R9=82 R2=R4=R6=R8=R10=130 C1=C2=C3=C5=C6=0.1F C4=10F L1=L2=1H Vcc C1 C3 L2 C2 C4 Rx Vcc Tx Vcc Recommended Circuit Schematic (3.3V/5V) B-15/13-155C-TDFB(3)-Sxx5(7) Tx Vcc C5 Rx Vcc 9 R1 7 8 6 5 4 3 2 1 R5 R3 C6 R7 TD + RD + TD - RD - Tx Vcc SD Rx Vcc R2 R4 Notes +3.3V: R1=R3=R5=R7=130 R2=R4=R6=R8=82 C1=C2=C3=C5=C6=0.1F C4=10F L1=L2=1H No internal connection Transceiver Top view R6 No internal connection R8 L1 Notes +5V: R1=R3=R5=R7=82 R2=R4=R6=R8=130 C1=C2=C3=C5=C6=0.1F C4=10F L1=L2=1H Vcc C3 C1 L2 C4 C2 Rx Vcc Tx Vcc The split-loaded terminations for ECL signals need to be located at the input of devices receiving those ECL signals. The power supply filtering is required for good EMI performance. Use short tracks from the inductor L1/L2 to the module Rx Vcc. A GND plane under the module is required for good EMI and sensitivity performance. LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 4 LUMNDS581-Apr2107 Rev A.3 155 Mbps Bi-directional Receptacle Single Fiber Transceiver B-15/13-155(C)-TDFB(3)-Sxx5(7) Package Diagram Diplexer B-15/13-155-TDFB(3)-SSC5(7) Transceiver Assembly (Receptacle Type) Top View Front View Rear View Side View LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 5 LUMNDS581-Apr2107 Rev A.3 155 Mbps Bi-directional Receptacle Single Fiber Transceiver B-15/13-155(C)-TDFB(3)-Sxx5(7) Package Diagram B-15/13-155-TDFB(3)-SFC5(7) Top View Front View Package Diagram B-15/13-155-TDFB(3)-SST5(7) Top View LUMINENTOIC.COM Front View 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 6 LUMNDS581-Apr2107 Rev A.3 155 Mbps Bi-directional Receptacle Single Fiber Transceiver B-15/13-155(C)-TDFB(3)-Sxx5(7) Ordering Information Available Options: B-15/13-155(C)-TDFB-SSC5(7) B-15/13-155(C)-TDFB-SFC5(7) B-15/13-155(C)-TDFB-SST5(7) B-15/13-155(C)-TDFB3-SSC5(7) B-15/13-155(C)-TDFB3-SFC5(7) B-15/13-155(C)-TDFB3-SST5(7) B-15/13-155(C)-TDFB-SSC5(7)-G5 B-15/13-155(C)-TDFB-SFC5(7)-G5 B-15/13-155(C)-TDFB-SST5(7)-G5 B-15/13-155(C)-TDFB3-SSC5(7)-G5 B-15/13-155(C)-TDFB3-SFC5(7)-G5 B-15/13-155(C)-TDFB3-SST5(7)-G5 Part Numbering Definitions: B - 15/13 - 155 - TDFB(3) - S XX Tx Power -RoHS • Wavelength Tx Wavelength=1550nm Rx Wavelength=1310nm • Communication protocol 155 = LVPECL SD output 155C = LVTTL SD output • TDFB = +5V Transceiver • TDFB3 = +3.3V Transceiver • Single mode fiber • Connector options SC/ST/FC • Tx Power 5 = -5 to 0 dBm 7 = -3 to +2 dBm • RoHS Blank = RoHS non-compliant product G5 = RoHS compliant LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 7 LUMNDS581-Apr2107 Rev A.3 155 Mbps Bi-directional Receptacle Single Fiber Transceiver B-15/13-155(C)-TDFB(3)-Sxx5(7) Warnings Handling Precautions: This device is susceptible to damage as a result of electrostatic discharge (ESD). A static free environment is highly recommended. Follow guidelines according to proper ESD procedures. Laser Safety: Radiation emitted by laser devices can be dangerous to human eyes. Avoid eye exposure to direct or indirect radiation. Legal Notice IMPORTANT NOTICE! All information contained in this document is subject to change without notice, at LuminentOIC’s sole and absolute discretion. LuminentOIC warrants performance of its products to current specifications only in accordance with the company’s standard one-year warranty; however, specifications designated as “preliminary” are given to describe components only, and LuminentOIC expressly disclaims any and all warranties for said products, including express, implied, and statutory warranties, warranties of merchantability, fitness for a particular purpose, and non-infringement of proprietary rights. Please refer to the company’s Terms and Conditions of Sale for further warranty information. LuminentOIC assumes no liability for applications assistance, customer product design, software performance, or infringement of patents, services, or intellectual property described herein. No license, either express or implied, is granted under any patent right, copyright, or intellectual property right, and LuminentOIC makes no representations or warranties that the product(s) described herein are free from patent, copyright, or intellectual property rights. Products described in this document are NOT intended for use in implantation or other life support applications where malfunction may result in injury or death to persons. LuminentOIC customers using or selling products for use in such applications do so at their own risk and agree to fully defend and indemnify LuminentOIC for any damages resulting from such use or sale. THE INFORMATION CONTAINED IN THIS DOCUMENT IS PROVIDED ON AN “AS IS” BASIS. Customer agrees that LuminentOIC is not liable for any actual, consequential, exemplary, or other damages arising directly or indirectly from any use of the information contained in this document. Customer must contact LuminentOIC to obtain the latest version of this publication to verify, before placing any order, that the information contained herein is current. © LuminentOIC, Inc. 2003 All rights reserved LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 8 LUMNDS581-Apr2107 Rev A.3