The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. 0.5mm pitch, 2.5mm above the board,high speed transmission connector for shielded FFC FH41 Series THine Electronics, Inc. Next-generation chipset (V-by-One®HS*) Compatible connector ＊High-speed serial interface technology for image transmission Space saving (68 pos. shown) 2.5mm 38mm ■Features 1.Compatibility with impedance control, shield FFC The FH41 series is equipped with a GND exclusive terminal and available for connection with impedance control, shield FFC. 2.Differential impedance 100Ω±10% 6.2mm figure.1 The FH41 series features a terminal design considering impedance control, and making high speed transmission possible. Sig 0.5 nal co mm nta pitc ct h 3.Highly reliable connection, tough structure The FH41 series follows the structure of the proven FH28 series, and achieves: - High reliability thanks to the FFC positioning mechanism - Reliable connection operation and no unlocking thanks to the durable structure. 4.One-finger operation of the actuator Proven (in several other Hirose's connectors!) Flip-Lock rotating actuator assures reliable mechanical and electrical connection with FPC, confirming it with a definite tactile feel. 5.Board placement with automatic equipment figure.2 Flat upper surface and tape and reel packaging facilitate vacuum pick-up and placement. Standard reel packaging contains 2,500 connectors. Gro 2.5 und mm con pitc tact h Signal contact connection area 6.Halogen-free * *As defined by IEC61249-2-21 Br-900ppm maximum, Cl-900ppm maximum, Cl + Br combined-1,500ppm maximum FFC figure.3 GND contact connection area 2010.9 1 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. FH41 Series●0.5mm pitch, 2.5mm above the board,high speed transmission connector for shielded FFC ■Specifications Current rating 0.5 A(Note1) Voltage rating 50 Vrms AC Ratings Recommended FPC Thickness Operating temperature range: -40 to +85°C (Note 2) Operating humidity range: Relative humidity 90% max. (No condensation) Storage temperature range: -10 to +50°C (Note 3) Storage humidity range: Relative humidity 90% max. (No condensation) 0.3 ±0.05 mm, Gold plated contact pads (GND plate:t=0.5±0.05mm,tin plateing) Item Specification Conditions 1.Insulation resistance 500 Mø min. 100 V DC 2.Withstanding voltage No flashover or insulation breakdown 150 Vrms AC / one minute 3.Contact resistance 100 mø max. * Including FFC conductor resistance 1 mA, AC max (AC: 1kHz) 4.Durability Contact resistance: 100 mø max. No damage, cracks, or parts dislocation 20 cycles 5.Vibration No electrical discontinuity of 1μs or longer Contact resistance: 100 mø max. No damage, cracks, or parts dislocation Frequency: 10 to 55 Hz, single amplitude of 0.75mm, 10 cycles in each of the 3 directions 6.Shock No electrical discontinuity of 1μs or longer Contact resistance: 100 mø max. No damage, cracks, or parts dislocation Acceleration of 981m/s 6 ms duration, sine halfwave, 3 cycles in each of the 3 axis 7.Humidity (Steady state) Contact resistance: 100 mø max. Insulation resistance: 50 Mø min. No damage, cracks, or parts dislocation 96 hours at 40°C and humidity of 90 to 95% 8.Temperature cycle Contact resistance: 100 mø max. Insulation resistance: 50 Mø min. No damage, cracks, or parts dislocation Temperature : -40°C → +15°C to +35°C → +85°C → +15°C to +35°C Time: 30 → 2 to 3 → 30 → 2 to 3 minutes 5 cycles 9.Resistance to soldering heat No deformation of components affecting performance Reflow: At the recommended temperature profile Manual soldering: 350°C ±5°C for 5 seconds 2 Note 1. When passing the current through all of the contacts, use 70% of the rated current. Note 2.Includes temperature rise caused by current flow. Note 3. The term "storage" refers to products stored for a long period prior to mounting and use. The operating temperature and humidity range covers the non-conducting condition of installed connectors in storage, shipment or during transportation after board mounting. Note 4. Information contained in this catalog represents general requirements for this Series. Contact us for the drawings and specifications for a specific part number shown. ■Materials Part Material Insulator LCP Contacts Phosphor bronze Metal fittings Brass Finish Remarks Color:Gray UL94V-0 Color:Black Gold plated --------- Pure tin reflow plated ■Ordering information FH 41 − 50S − 0.5 SH (05) ❶ ❷ ❸ ❶ Series name : FH ❷ Series No.: 41 ❸ Number of positions : 28 to 68 ❹ Contact pitch : 0.5mm 2 ❹ ❺ ❻ ❺ SH : SMT horizontal mounting type ❻ Plating specifications :(05)…Gold plated The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. FH41 Series●0.5mm pitch, 2.5mm above the board,high speed transmission connector for shielded FFC ■Connector Dimensions C D (5.05) 1 (5.45) (0.12) No. of contacts Cavity No. 2.5 (0.12) (0.15) 2 2.5 (4.7) E 0.25 0.8 (Dimension for FFC opening) 6.2 G Note 1. The coplanarity of each terminal lead within specified dimension is 0.1 mm Max. 2. Packaged on tape and reel only. Check packaging specification. 3. Slight variations in color of the plastic compounds do not affect form, fit or function of the connector. 4. After reflow, the terminal plating may change color, however this does not represent a quality issue. Unit : mm Part Number CL No. FH41-28S-0.5SH(05) 580-2208-1-05 28 FH41-40S-0.5SH(05) 580-2205-3-05 40 FH41-50S-0.5SH(05) 580-2204-0-05 580-2202-5-05 FH41-68S-0.5SH(05) Number of contacts No. of Contacts(GND contacts) C D E F G 5 18 8 24 13.5 10 14.57 15.95 19.5 17.5 20.57 21.95 50 10 68 13 29 24.5 22.5 25.57 26.95 38 33.5 30 34.57 35.95 Note1.Tape and reel packaging (2,500 pieces/reel). Order by number of reels. 3 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. FH41 Series●0.5mm pitch, 2.5mm above the board,high speed transmission connector for shielded FFC ■Recommended PCB mounting pattern and metal mask dimensions D±0.05 1.2±0.05(Land pattern) 1±0.05(Metal mask) 6.6±0.1 6.35±0.05 0.65±0.05 1.55±0.05 0.3±0.03 (Land pattern) 0.25±0.03(Metal mask) 0.5±0.05 1±0.05 0.3±0.03(Land pattern) 0.2±0.0(Metal mask) 2.5±0.05 0.4±0.03 E±0.05 H±0.05 Recommended metal mask thickness t=0.1 ■Recommended FFC Dimensions 0.5±0.1 5.5MIN 2.7±0.5 .2 0.5±0.05 0.3±0.05 0.1MIN 5.5MIN 17.7MAX R0 0.5±0.05 0.3±0.03 1.9±0.1 2.6±0.1 3.8±0.1 2- 2.2±0.5 0.2 2-R J±0.1 K±0.07 D±0.05 0.2m ax 1 Shield area 2-R 2-R 0.2 ma x Ground plate Note 1 Please overlap shield plate on ground plate. Unit : mm Part Number CL No. FH41-28S-0.5SH(05) 580-2208-1-05 Number of contacts No. of Contacts(GND contacts) 28 FH41-40S-0.5SH(05) 580-2205-3-05 FH41-50S-0.5SH(05) 580-2204-0-05 FH41-68S-0.5SH(05) 580-2202-5-05 Note1.Tape and reel packaging (2,500 pieces/reel). Order by number of reels. 4 H J K 5 16 15.7 14.5 40 8 22 21.7 20.5 50 10 27 26.7 25.5 68 13 36 35.7 34.5 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. FH41 Series●0.5mm pitch, 2.5mm above the board,high speed transmission connector for shielded FFC ■Recommended FFC construction Material Name Material thickness(μm) thickness(μm) Shielding Material Conouctiye Adhesive Polyester Type Copper Film (Tin Plated) 1 Adhesive Acrylic Type 24 1 Base Material Polyester Type 12 1 Adhesive Acrylic Type 24 1 Insulated Layer Polyester Type ２５ Adhesive Polyester Type ３５ Soft Copper Film (Nickel Under Plated / Gold Plated) 35 35 Adhesive Polyester Type 35 35 Insulated Layer Polyester Type 25 25 Adhesive Polyester Type 30 30 Siiffener Polyester Type 188 188 503 313 Total Note 1 70 Please overlap shield plate on ground plate. 5 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. FH41 Series●0.5mm pitch, 2.5mm above the board,high speed transmission connector for shielded FFC ■Packaging Specification ●Embossed Carrier Tape Dimensions 1.75±0.1 N±0.1 M±0.1 L±0.3 0 0 .1 11 4±0.1 2±0.1 12±0.1 (P) (Q) (R) L±0.3 N±0.1 (2.9) (0.3) .5 ＋ 1.75±0.1 .5 ＋ 11 4±0.1 2±0.1 12±0.1 (P) (Q) (R) (2.9) (0.3) (Tape width of 32mm min.) 0 0 .1 (Tape width of 24mm max.) (1.64:Vacum pick up area) (5.75) (7.35) Ｃ Ｌ (1.64:Vacum pick up area) (5.75) (7.35) Direction of unreeling Ｃ Ｌ Direction of unreeling (Ø1 3) ●Reel Dimensions (Ø80) (Ø380) (S:Outside) (T:Inside) Trailer Portion equipped with connectors Leader (400mm min) Embossed carrier tape 14 Empty component compartments min Top cover tape 10 Empty component compartments min 6 Unit : mm Part Number CL No. FH41-28S-0.5SH(05) 580-2208-1-05 Number of contacts No. of Contacts(GND contacts) 28 5 L 32 M N P 28.4 14.2 18.3 Q 17 R S T 15.7 37.4 33.4 FH41-40S-0.5SH(05) 580-2205-3-05 40 8 44 40.4 20.2 24.3 23 21.7 49.4 45.4 FH41-50S-0.5SH(05) 580-2204-0-05 50 10 44 40.4 20.2 29.3 28 26.7 49.4 45.4 FH41-68S-0.5SH(05) 580-2202-5-05 68 13 56 52.4 26.2 38.3 37 35.7 61.4 57.4 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. FH41 Series●0.5mm pitch, 2.5mm above the board,high speed transmission connector for shielded FFC ■Temperature Profile MAX 250℃ Temperature (ç) 250 230℃ 200 HRS test condition Solder method Environment Solder composition 200℃ 150 Test board Land dimensions Metal mask 150℃ :Reflow, IR/hot air :Room air :Paste, 96.5%Sn/3.0%Ag/0.5%Cu (Senju Metal Industry, Co., Ltd.'s Part Number:M705-221CM5-32-10.5) :Glass epoxy 30mm×60mm×0.8mm thick :0.3mm×0.65mm, 0.3mm×1.2mm :0.25×0.65, 0.2×0.1mm thick The temperature profiles shown are based on the above conditions. In individual applications the actual temperature may vary, depending on solder paste type, volume / thickness and board size / thickness. Consult your solder paste and equipment manufacturer for specific recommendations. 100 50 25℃ （60sec.） 0 90~120sec. Preheating （60sec.） soldering Start Time(Seconds) 7 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. FH41 Series●0.5mm pitch, 2.5mm above the board,high speed transmission connector for shielded FFC ■Operation and Precautions Operation 1.FFC insertion procedure. Connector installed on the board. Precautions ❶ Do not force the actuator to open beyond its fully open position. Do not use any type of tool to open the actuator. ❶ Lift up the actuator. Use thumb or index finger 110° ❷ Fully insert the FFC in the connector parallel to mounting surface, with the exposed conductive traces facing down. ❷ Do not forcefully bend the FFC upward. Consult FFC manufacturer for the recommended bend radiuses. ❸ Rotate down the actuator until firmly closed. It is critical that the inserted FFC is not moved and remains fully inserted. ❸ For connectors with multiple contacts, such as 80 pos. rotate down the actuator pushing at both ends. 2.FFC removal ❹ Load to FFC Be very careful not to apply any force to the connector directly after inserting FFC. Otherwise, the connector may become unlocked or the FFC may break. In particular, design the FFC layout with care not to bend it sharply upward in a vertial direction near the insertion opening. Fix the FFC when loads are applied to it continuously. Fully open the actuator. Carefully withdraw the FFC exercising caution not to deform or damage it. 8 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. FH41 Series●0.5mm pitch, 2.5mm above the board,high speed transmission connector for shielded FFC ■Precautions (mating/un-mating FFC with the retention tabs) Precautions Operation 1.How to insert Insert the cable into the interspace between the mold walls ) at both ends of entrance where the connector is ( inserted and the guide walls ( ) at both ends of interior connector so the cable tabs are properly located. ❷ Avoid “ride on” Avoid insertion so the cables ride on any guide. Be sure NOT to close the actuator as the cables ride on any guide. It may cause conduction failure. Ride on a left guide Ride on a right guide Correct insertion 2.Precautions when mating /un-mating ❶ Avoid insertion in diagonal direction. Do not insert the cable in diagonal direction. A part of the connector may touches the contacts resulting in deformation of the contacts. Insert the cable straight into the connector and hook the cable tabs with the guide. After insertion, slightly pull the cables to make sure the cable tabs are firmly secured. No removal of the cable means correct insertion. ① Insert the cable straight and obliquely from above. Do not close the actuator as the cables ride on. In the event it is locked as the cables ride on a guide, absolutely avoid moving the cable. In this case, open the actuator and re-insert the cable as instructed in “ 1.How to insert” Do not move the cables back and forth and around as the cables ride on the guide when the actuator is closed. ② Slightly pull the cable to make sure the tabs are firmly secured. ③ Close the actuator. 9