CY7C68033/CY7C68034 EZ-USB® NX2LP-Flex™ Flexible USB NAND Flash Controller EZ-USB® NX2LP-Flex™ Flexible USB NAND Flash Controller CY7C68033/CY7C68034 Silicon Features ■ Certified compliant for bus- or self-powered USB 2.0 operation (TID# 40490118) ■ Single-chip, integrated USB 2.0 transceiver and smart SIE ■ Ultra low power – 43 mA typical current draw in any mode ■ Enhanced 8051 core ❐ Firmware runs from internal RAM that is downloaded from NAND Flash at startup ❐ No external EEPROM required ■ 15 KBytes of on-chip code/data RAM ❐ Default NAND firmware – 8 kB ❐ Default free space – 7 kB ■ Four programmable bulk/interrupt/isochronous endpoints ❐ Buffering options: double, triple, and quad ■ Additional programmable (bulk/interrupt) 64-byte endpoint ■ SmartMedia standard hardware ECC generation with 1-bit correction and 2-bit detection ■ ■ ■ Integrated, industry-standard enhanced 8051 ❐ 48-MHz, 24-MHz, or 12-MHz CPU operation ❐ Four clocks for each instruction cycle ❐ Three counter/timers ❐ Expanded interrupt system ❐ Two data pointers ■ 3.3-V operation with 5 V tolerant inputs ■ Vectored USB interrupts and GPIF/FIFO interrupts ■ Separate data buffers for the setup and data portions of a control transfer ■ Integrated I2C controller, runs at 100 or 400 kHz ■ Four integrated FIFOs ❐ Integrated glue logic and FIFOs lower system cost ❐ Automatic conversion to and from 16-bit buses ❐ Master or slave operation ❐ Uses external clock or asynchronous strobes ❐ Easy interface to ASIC and DSP ICs ■ Available in space saving 56-pin QFN package General programmable interface (GPIF) ❐ Enables direct connection to most parallel interfaces ❐ Programmable waveform descriptors and configuration registers to define waveforms ❐ Supports multiple ready (RDY) inputs and control (CTL) outputs CY7C68034 Only Silicon Features 12 fully programmable general purpose I/O (GPIO) pins ■ ■ Ideal for battery powered applications ❐ Suspend current: 100 A (typ) CY7C68033 Only Silicon Features Ideal for non-battery powered applications ❐ Suspend current: 300 A (typ) Logic Block Diagram High-performance, enhanced 8051 core with low power options 24 MHz Ext. Xtal NX2LP-Flex /0.5 /1.0 /2.0 8051 Core 12/24/48 MHz, four clocks/cycle VCC Connected for full speed USB 1.5k NAND Boot Logic (ROM) D+ D– USB 2.0 XCVR Integrated full- and high speed XCVR CY Smart USB 1.1/2.0 Engine 15 kB RAM I 2C Master Address (16)/Data Bus (8) x 20 PLL Additional I/Os GPIF RDY (2) CTL (3) ECC Up to 96 MB/s burst rate 4 kB FIFO Enhanced USB core simplifies 8051 code Cypress Semiconductor Corporation Document Number: 001-04247 Rev. *J • General Programmable I/F to ASIC/DSP or bus standards such as 8-bit NAND, EPP, and so on. ‘Soft Configuration’ enables easy firmware changes 198 Champion Court 8/16 FIFO and USB endpoint memory (master or slave modes) • San Jose, CA 95134-1709 • 408-943-2600 Revised July 6, 2012 CY7C68033/CY7C68034 ■ Because the NX2LP-Flex is intended for NAND Flash-based USB mass storage applications, a default firmware image is included in the development kit with the following features: Industry standard (SmartMedia) page management for wear leveling algorithm, bad block handling, and physical to logical management. ■ 8-bit NAND Flash interface support ■ High (480 Mbps) or full (12 Mbps) speed USB support ■ Support for 30 ns, 50 ns, and 100 ns NAND Flash timing ■ NAND sizes supported per chip select ❐ 512 bytes for up to 1 Gb capacity ❐ 2K bytes for up to 8 Gb capacity ❐ 4K bytes for up to 16 Gb capacity ■ Complies with the USB mass storage class specification revision 1.0 Default NAND Firmware Features ® ■ ■ 12 configurable GPIO pins ❐ Two dedicated chip enable (CE#) pins ❐ Six configurable CE#/GPIO pins • Up to eight NAND Flash single-device (single-die) chips are supported • Up to four NAND Flash dual-device (dual-die) chips are supported • Compile option enables unused CE# pins to be configured as GPIOs ❐ Four dedicated GPIO pins Industry standard ECC NAND Flash correction ❐ 1 bit for every 256-bit correction ❐ 2-bit error detection Document Number: 001-04247 Rev. *J The default firmware image implements a USB 2.0 NAND Flash controller. This controller adheres to the Mass Storage Class Bulk-Only Transport Specification. The USB port of the NX2LP-Flex is connected to a host computer directly or through the downstream port of a USB hub. The host software issues commands and data to the NX2LP-Flex and receives status and data from the NX2LP-Flex using standard USB protocol. The default firmware image supports industry leading 8-bit NAND Flash interfaces and both common NAND page sizes of 512 and 2k bytes. Up to eight CE# pins enable the NX2LP-Flex to be connected to up to eight single or four dual-die NAND Flash chips. Complete source code and documentation for the default firmware image are included in the NX2LP-Flex development kit to enable customization for meeting design requirements. Additionally, compile options for the default firmware enable quick configuration of some features to decrease design effort and increase time-to-market advantages. Page 2 of 40 CY7C68033/CY7C68034 Contents Overview ............................................................................ 4 Applications ...................................................................... 4 Functional Overview ........................................................ 4 USB Signaling Speed .................................................. 4 8051 Microprocessor ................................................... 4 I2C Bus ........................................................................ 5 Buses .......................................................................... 6 Enumeration ................................................................ 6 Default Silicon ID Values ............................................. 7 ReNumeration™ .......................................................... 7 Bus-powered Applications ........................................... 7 Interrupt System .......................................................... 7 Reset and Wakeup ...................................................... 9 Program/Data RAM ................................................... 10 Register Addresses ................................................... 10 Endpoint RAM ........................................................... 11 External FIFO Interface ............................................. 13 GPIF .......................................................................... 13 ECC Generation ........................................................ 13 Autopointer Access ................................................... 14 I2C Controller ............................................................ 14 Pin Assignments ............................................................ 15 Register Summary .......................................................... 21 Absolute Maximum Ratings .......................................... 28 Operating Conditions ..................................................... 28 Document Number: 001-04247 Rev. *J DC Characteristics ......................................................... 28 USB Transceiver ....................................................... 28 AC Electrical Characteristics ........................................ 28 USB Transceiver ....................................................... 28 Slave FIFO Asynchronous Read ............................... 29 Slave FIFO Asynchronous Write ............................... 29 Slave FIFO Asynchronous Packet End Strobe ......... 30 Slave FIFO Output Enable ........................................ 30 Slave FIFO Address to Flags/Data ............................ 31 Slave FIFO Asynchronous Address .......................... 31 Sequence Diagram .................................................... 32 Ordering Information ...................................................... 34 Ordering Code Definitions ......................................... 34 Package Diagrams .......................................................... 35 PCB Layout Recommendations .................................... 36 Quad Flat Package No Leads (QFN) Package Design Notes ................................................................... 36 Acronyms ........................................................................ 38 Document Conventions ................................................. 38 Units of Measure ....................................................... 38 Document History Page ................................................. 39 Sales, Solutions, and Legal Information ...................... 40 Worldwide Sales and Design Support ....................... 40 Products .................................................................... 40 PSoC Solutions ......................................................... 40 Page 3 of 40 CY7C68033/CY7C68034 Overview Figure 1. Example DVB Block Diagram Cypress Semiconductor Corporation’s EZ-USB® NX2LP-Flex (CY7C68033/CY7C68034) is a firmware-based, programmable version of the EZ-USB NX2LP (CY7C68023/CY7C68024), which is a fixed-function, low power USB 2.0 NAND Flash controller. By integrating the USB 2.0 transceiver, serial interface engine (SIE), enhanced 8051 microcontroller, and a programmable peripheral interface in a single chip, Cypress has created a very cost-effective solution that enables feature-rich NAND Flash-based applications. I/O Buttons LCD I/O CTL NX2LPFlex D+/- DVB Decoder Figure 2. Example GPS Block Diagram NAND-Based GPS Unit I/O D+/- NAND Flash-based DVB video capture devices ■ Wireless pointer/presenter tools with NAND Flash storage ■ NAND Flash-based MPEG/TV conversion devices ■ Legacy conversion devices with NAND Flash storage ■ NAND Flash-based cameras ■ NAND Flash mass storage device with biometric (for example, fingerprint) security ■ Home PNA devices with NAND Flash storage ■ Wireless LAN with NAND Flash storage ■ NAND Flash-based MP3 players ■ LAN networking with NAND Flash storage CTL NX2LPFlex CE[7:0] NAND Bank(s) I/O I/O The NX2LP-Flex enables designers to add extra functionality to basic NAND Flash mass storage designs, or to interface them with other peripheral devices. Applications may include: ■ Buttons I/O LCD Applications NAND Flash-based GPS devices NAND Bank(s) I/O Audio / Video I/O The GPIF and master/slave endpoint FIFO (8- or 16-bit data bus) provide an easy and glueless interface to popular interfaces such as UTOPIA, EPP, I2C, PCMCIA, and most DSP processors. ■ CE[7:0] I/O The ingenious architecture of NX2LP-Flex results in USB data transfer rates of over 53 Mbytes per second, the maximum allowable USB 2.0 bandwidth, while still using a low cost 8051 microcontroller in a small 56-pin QFN package. Because it incorporates the USB 2.0 transceiver, the NX2LP-Flex is more economical, providing a smaller footprint solution than external USB 2.0 SIE or transceiver implementations. With EZ-USB NX2LP-Flex, the Cypress Smart SIE handles most of the USB 1.1 and 2.0 protocol, freeing the embedded microcontroller for application-specific functions and decreasing development time while ensuring USB compatibility. NAND-Based DVB Unit GPS The “Reference Designs” section of the Cypress web site provides additional tools for typical USB 2.0 applications. Each reference design comes complete with firmware source and object code, schematics, and documentation. Functional Overview USB Signaling Speed NX2LP-Flex operates at two of the three rates defined in the USB Specification Revision 2.0, dated April 27, 2000: ■ Full speed, with a signaling bit rate of 12 Mbps ■ High speed, with a signaling bit rate of 480 Mbps. NX2LP-Flex does not support the low speed signaling mode of 1.5 Mbps. 8051 Microprocessor The 8051 microprocessor embedded in the NX2LP-Flex has 256 bytes of register RAM, an expanded interrupt system and three timer/counters. Document Number: 001-04247 Rev. *J Page 4 of 40 CY7C68033/CY7C68034 8051 Clock Frequency Special Function Registers NX2LP-Flex has an on-chip oscillator circuit that uses an external 24 MHz (±100 ppm) crystal with the following characteristics: Certain 8051 SFR addresses are populated to provide fast access to critical NX2LP-Flex functions. These SFR additions are shown in Table 1 on page 6. Bold type indicates non-standard, enhanced 8051 registers. The two SFR rows that end with ‘0’ and ‘8’ contain bit-addressable registers. The four I/O ports A–D use the SFR addresses used in the standard 8051 for ports 0–3, which are not implemented in NX2LP-Flex. Because of the faster and more efficient SFR addressing, the NX2LP-Flex I/O ports are not addressable in external RAM space (using the MOVX instruction). ■ Parallel resonant ■ Fundamental mode ■ 500 W drive level ■ 12 pF (5% tolerance) load capacitors. An on-chip PLL multiplies the 24-MHz oscillator up to 480 MHz, as required by the transceiver/PHY, and internal counters divide it down for use as the 8051 clock. The default 8051 clock frequency is 12 MHz. The clock frequency of the 8051 can be changed by the 8051 through the CPUCS register, dynamically Figure 3. Crystal Configuration C1 24 MHz C2 12 pF I2C Bus NX2LP supports the I2C bus as a master only at 100/400 kHz. SCL and SDA pins have open-drain outputs and hysteresis inputs. These signals must be pulled up to 3.3 V, even if no I2C device is connected. The I2C bus is disabled at startup and only available for use after the initial NAND access. 12 pF 20 × PLL 12-pF capacitor values assumes a trace capacitance of 3 pF per side on a four-layer FR4 PCA Document Number: 001-04247 Rev. *J Page 5 of 40 CY7C68033/CY7C68034 Table 1. Special Function Registers x 8x 9x Ax Bx Cx Dx Ex Fx 0 IOA IOB IOC IOD SCON1 PSW ACC B SBUF1 EICON EIE EIP 1 SP EXIF INT2CLR IOE 2 DPL0 MPAGE INT4CLR OEA 3 DPH0 OEB 4 DPL1 OEC 5 DPH1 OED 6 DPS OEE 7 PCON 8 TCON 9 TMOD SBUF0 A TL0 AUTOPTRH1 B TL1 C TH0 D TH1 AUTOPTRH2 GPIFSGLDATH E CKCON AUTOPTRL2 GPIFSGLDATLX F SCON0 IE IP T2CON EP2468STAT EP01STAT RCAP2L AUTOPTRL1 EP24FIFOFLGS GPIFTRIG RCAP2H RESERVED EP68FIFOFLGS RESERVED AUTOPTRSETUP TL2 TH2 GPIFSGLDATLNOX Buses The NX2LP-Flex features an 8- or 16-bit ‘FIFO’ bidirectional data bus, multiplexed on I/O ports B and D. The default firmware image implements an 8-bit data bus in GPIF master mode. It is recommended that additional interfaces added to the default firmware image use this 8-bit data bus. Enumeration During the startup sequence, internal logic checks for the presence of NAND Flash with valid firmware. If valid firmware is found, the NX2LP-Flex loads it and operates according to the firmware. If no NAND Flash is detected, or if no valid firmware is found, the NX2LP-Flex uses the default values from internal ROM space for manufacturing mode operation. The two modes of operation are described in the section Normal Operation Mode on page 7 and Manufacturing Mode on page 7. Document Number: 001-04247 Rev. *J Page 6 of 40 CY7C68033/CY7C68034 Figure 4. NX2LP-Flex Enumeration Sequence Start-up Yes NAND Flash Present? No Default Silicon ID Values To facilitate proper USB enumeration when no programmed NAND Flash is present, the NX2LP-Flex has default silicon ID values stored in ROM space. The default silicon ID values should only be used for development purposes. Designers must use their own Vendor ID for final products. A Vendor ID is obtained through registration with the USB Implementor’s Forum (USB-IF). If the NX2LP-Flex is used as a mass storage class device, a unique USB serial number is required for each device to comply with the USB Mass Storage class specification. Cypress provides all the software tools and drivers necessary to properly programme and test the NX2LP-Flex. Refer to the documentation in the development kit for more information on these topics. NAND Flash Programmed? Table 2. Default Silicon ID Values No Default VID/PID/DID Yes Load Firmware From NAND Load Default Descriptors and Configuration Data Vendor ID 0x04B4 Cypress Semiconductor Product ID 0x8613 EZ-USB® Default Device release 0xAnnn Depends on chip revision (nnn = chip revision, where first silicon = 001) ReNumeration™ Cypress’s ReNumeration feature is used in conjunction with the NX2LP-Flex manufacturing software tools to enable first-time NAND programming. It is only available when used in conjunction with the NX2LP-Flex manufacturing tools, and is not enabled during normal operation. Enumerate According To Firmware Enumerate As Unprogrammed NX2LP-Flex Normal Operation Mode Manufacturing Mode Bus-powered Applications The NX2LP-Flex fully supports bus-powered designs by enumerating with less than 100 mA, as required by the USB 2.0 specification. Interrupt System Normal Operation Mode In normal operation mode, the NX2LP-Flex behaves as a USB 2.0 Mass Storage Class NAND Flash controller. This includes all typical USB device states (powered, configured, and so on). The USB descriptors are returned according to the data stored in the configuration data memory area. Normal read and write access to the NAND Flash is available in this mode. Manufacturing Mode In manufacturing mode, the NX2LP-Flex enumerates using the default descriptors and configuration data that are stored in internal ROM space. This mode enables for first time programming of the configuration data memory area, and board level manufacturing tests. Document Number: 001-04247 Rev. *J INT2 Interrupt Request and Enable Registers NX2LP-Flex implements an autovector feature for INT2 and INT4. There are 27 INT2 (USB) vectors and 14 INT4 (FIFO/GPIF) vectors. For more details, refer to the EZ-USB Technical Reference Manual (TRM). USB-Interrupt Autovectors The main USB interrupt is shared by 27 interrupt sources. To save the code and processing time normally required to identify the individual USB interrupt source, the NX2LP-Flex provides a second level of interrupt vectoring, called Autovectoring. When a USB interrupt is asserted, the NX2LP-Flex pushes the program counter to its stack and then jumps to address 0x0500; it expects to find a ‘jump’ instruction to the USB Interrupt service routine here. Developers familiar with Cypress’s programmable USB devices should note that these interrupt vector values differ from those used in other EZ-USB microcontrollers. This is due to the additional NAND boot logic that is present in the NX2LP-Flex ROM space. Also, these values are fixed and cannot be changed in the firmware. Page 7 of 40 CY7C68033/CY7C68034 Table 3. INT2 USB Interrupts USB Interrupt Table For INT2 Priority INT2VEC Value Source Notes 1 0x500 SUDAV Setup data available 2 0x504 SOF Start of frame (or microframe) 3 0x508 SUTOK Setup token received 4 0x50C SUSPEND USB suspend request 5 0x510 USB RESET Bus reset 6 0x514 HISPEED Entered high speed operation 7 0x518 EP0ACK NX2LP ACK’d the CONTROL handshake 8 0x51C Reserved 9 0x520 EP0-IN EP0-IN ready to be loaded with data 10 0x524 EP0-OUT EP0-OUT has USB data 11 0x528 EP1-IN EP1-IN ready to be loaded with data 12 0x52C EP1-OUT EP1-OUT has USB data 13 0x530 EP2 IN: buffer available. OUT: buffer has data 14 0x534 EP4 IN: buffer available. OUT: buffer has data 15 0x538 EP6 IN: buffer available. OUT: buffer has data 16 0x53C EP8 IN: buffer available. OUT: buffer has data 17 0x540 IBN 18 0x544 IN-Bulk-NAK (any IN endpoint) Reserved 19 0x548 EP0PING EP0 OUT was pinged and it NAK’d 20 0x54C EP1PING EP1 OUT was pinged and it NAK’d 21 0x550 EP2PING EP2 OUT was pinged and it NAK’d 22 0x554 EP4PING EP4 OUT was pinged and it NAK’d 23 0x558 EP6PING EP6 OUT was pinged and it NAK’d 24 0x55C EP8PING EP8 OUT was pinged and it NAK’d 25 0x560 ERRLIMIT Bus errors exceeded the programmed limit 26 0x564 Reserved 27 0x568 Reserved 28 0x56C Reserved 29 0x570 EP2ISOERR ISO EP2 OUT PID sequence error 30 0x574 EP4ISOERR ISO EP4 OUT PID sequence error 31 0x578 EP6ISOERR ISO EP6 OUT PID sequence error 32 0x57C EP8ISOERR ISO EP8 OUT PID sequence error If autovectoring is enabled (AV2EN = 1 in the INTSET-UP register), the NX2LP-Flex substitutes its INT2VEC byte. Therefore, if the high byte (‘page’) of a jump-table address is preloaded at location 0x544, the automatically inserted INT2VEC byte at 0x545 directs the jump to the correct address out of the 27 addresses within the page. FIFO/GPIF Interrupt (INT4) Just as the USB Interrupt is shared among 27 individual USB-interrupt sources, the FIFO/GPIF interrupt is shared among 14 individual FIFO/GPIF sources. The FIFO/GPIF Interrupt, such as the USB Interrupt, can employ autovectoring. Table 4 on page 9 shows the priority and INT4VEC values for the 14 FIFO/GPIF interrupt sources. Document Number: 001-04247 Rev. *J Page 8 of 40 CY7C68033/CY7C68034 Table 4. Individual FIFO/GPIF Interrupt Sources Priority INT4VEC Value Source 1 0x580 EP2PF Endpoint 2 programmable flag Notes 2 0x584 EP4PF Endpoint 4 programmable flag 3 0x588 EP6PF Endpoint 6 programmable flag 4 0x58C EP8PF Endpoint 8 programmable flag 5 0x590 EP2EF Endpoint 2 empty flag 6 0x594 EP4EF Endpoint 4 empty flag 7 0x598 EP6EF Endpoint 6 empty flag 8 0x59C EP8EF Endpoint 8 empty flag 9 0x5A0 EP2FF Endpoint 2 full flag 10 0x5A4 EP4FF Endpoint 4 full flag 11 0x5A8 EP6FF Endpoint 6 full flag 12 0x5AC EP8FF 13 0x5B0 GPIFDONE 14 0x5B4 GPIFWF If autovectoring is enabled (AV4EN = 1 in the INTSET-UP register), the NX2LP-Flex substitutes its INT4VEC byte. Therefore, if the high byte (‘page’) of a jump-table address is preloaded at location 0x554, the automatically inserted INT4VEC byte at 0x555 directs the jump to the correct address out of the 14 addresses within the page. When the ISR occurs, the NX2LP-Flex pushes the program counter to its stack and then jumps to address 0x553; it expects to find a ‘jump’ instruction to the ISR Interrupt service routine here. Reset and Wakeup Reset Pin The input pin RESET#, resets the NX2LP-Flex when asserted. This pin has hysteresis and is active LOW. When a crystal is Endpoint 8 full flag GPIF operation complete GPIF waveform used as the clock source for the NX2LP-Flex, the reset period must enable the stabilization of the crystal and the PLL. This reset period should be approximately 5 ms after VCC has reached 3.0V. If the crystal input pin is driven by a clock signal, the internal PLL stabilizes in 200 s after VCC has reached 3.0 V[1]. Figure 5 shows a POR condition and a reset applied during operation. A POR is defined as the time reset is asserted while power is being applied to the circuit. A powered reset is defined to be when the NX2LP-Flex has previously been powered on and operating and the RESET# pin is asserted. For more information on power on reset implementation for the EZ-USB family of products, refer to the application note EZ-USB FX2™/AT2™/SX2™. Figure 5. Reset Timing Plots RESET# RESET# VIL VIL 3.3 V 3.0 V 3.3 V VCC VCC 0V 0V TRESET Power-on Reset TRESET Powered Reset Note 1. If the external clock is powered at the same time as the CY7C68033/CY7C68034 and has a stabilization wait period, it must be added to the 200 s. Document Number: 001-04247 Rev. *J Page 9 of 40 CY7C68033/CY7C68034 Figure 6. Internal Code Memory Table 5. Reset Timing Values Condition TRESET Power-on reset with crystal Power-on reset with external clock source FFFF 7.5 kBytes USB registers and 4 kBytes FIFO buffers (RD#, WR#) 5 ms 200 s + Clock stability time Powered reset E200 E1FF 200 s E000 512 Bytes RAM Data (RD#, WR#)* Wakeup Pins The 8051 puts itself and the rest of the chip into a power down mode by setting PCON.0 = 1. This stops the oscillator and PLL. When WAKEUP is asserted by external logic, the oscillator restarts, after the PLL stabilizes, and then the 8051 receives a wakeup interrupt. This applies whether or not NX2LP-Flex is connected to the USB. 3FFF 15 kBytes RAM Code and Data (PSEN#, RD#, WR#)* The NX2LP-Flex exits the power down (USB suspend) state using one of the following methods: ■ USB bus activity (if D+/D– lines are left floating, noise on these lines may indicate activity to the NX2LP-Flex and initiate a wakeup). ■ External logic asserts the WAKEUP pin ■ External logic asserts the PA3/WU2 pin. The second wakeup pin, WU2, can also be configured as a GPIO pin. This enables a simple external R-C network to be used as a periodic wakeup source. Note that WAKEUP is, by default, active LOW. Program/Data RAM 0500 *SUDPTR, USB download, NAND boot access Register Addresses Figure 7. Internal Register Addresses FFFF 4 KBytes EP2-EP8 buffers (8 × 512) Internal ROM/RAM Size The NX2LP-Flex has 1 kBytes ROM and 15 kBytes of internal program/data RAM, where PSEN#/RD# signals are internally ORed to enable the 8051 to access it as both program and data memory. No USB control registers appear in this space. Internal Code Memory This mode implements the internal block of RAM (starting at 0x0500) as combined code and data memory, as shown in Figure 6. Only the internal and scratch pad RAM spaces have the following access: ■ USB download (only supported by the Cypress manufacturing tool) ■ Setup data pointer ■ NAND boot access. 1 kbyte ROM 0000 F000 EFFF 2 KBytes RESERVED E800 E7FF E7C0 E7BF E780 E77F E740 E73F E700 E6FF E500 E4FF E480 E47F E400 E3FF E200 E1FF 64 Bytes EP1IN 64 Bytes EP1OUT 64 Bytes EP0 IN/OUT 64 Bytes RESERVED 8051 Addressable Registers (512) Reserved (128) 128 bytes GPIF Waveforms Reserved (512) 512 bytes 8051 xdata RAM E000 Document Number: 001-04247 Rev. *J Page 10 of 40 CY7C68033/CY7C68034 Endpoint RAM Setup Data Buffer Size A separate 8-byte buffer at 0xE6B8-0xE6BF holds the setup data from a CONTROL transfer. ■ 3 × 64 bytes (Endpoints 0 and 1) ■ 8 × 512 bytes (Endpoints 2, 4, 6, 8) Endpoint Configurations (High Speed Mode) Organization ■ EP0 ❐ Bidirectional endpoint zero, 64-byte buffer ■ EP1IN, EP1OUT ❐ 64-byte buffers, bulk or interrupt ■ EP2, 4, 6, 8 ❐ Eight 512-byte buffers, bulk, interrupt, or isochronous. ❐ EP4 and EP8 can be double buffered, while EP2 and 6 can be either double, triple, or quad buffered. For high speed endpoint configuration options, see Figure 8. Endpoints 0 and 1 are the same for every configuration. Endpoint 0 is the only control endpoint, and endpoint 1 can be either bulk or interrupt. The endpoint buffers can be configured in any 1 of the 12 configurations shown in the vertical columns. When operating in full speed bulk mode, only the first 64 bytes of each buffer are used. For example, in high speed the max packet size is 512 bytes, but in full speed it is 64 bytes. Even though a buffer is configured to be a 512 byte buffer, in full speed only the first 64 bytes are used. The unused endpoint buffer space is not available for other operations. The following is an example endpoint configuration: EP2–1024 double buffered; EP6–512 quad buffered (column 8 in Figure 8). Figure 8. Endpoint Configuration EP0 IN&OUT 64 64 64 64 64 64 64 64 64 64 64 64 EP1 IN 64 64 64 64 64 64 64 64 64 64 64 64 EP1 OUT 64 64 64 64 64 64 64 64 64 64 64 64 EP2 EP2 EP2 EP2 EP2 EP2 EP2 EP2 EP2 EP2 512 512 512 512 512 512 512 512 512 512 512 512 EP4 EP4 512 512 512 512 512 512 512 512 512 512 512 512 EP6 EP6 EP6 EP6 EP6 EP6 512 512 512 512 512 512 EP8 512 512 512 1024 512 512 1 2 1024 Document Number: 001-04247 Rev. *J 3 1024 1024 512 512 1024 1024 1024 1024 1024 512 512 512 4 5 1024 6 EP6 1024 1024 512 EP6 EP6 512 512 512 512 EP6 512 1024 512 EP8 EP8 512 1024 512 EP4 1024 EP2 EP2 512 512 512 512 512 7 8 1024 9 1024 1024 EP8 EP8 512 512 512 512 10 11 1024 1024 12 Page 11 of 40 CY7C68033/CY7C68034 Default Full Speed Alternate Settings Table 6. Default Full Speed Alternate Settings [2, 3] Alternate Setting ep0 ep1out ep1in ep2 ep4 ep6 ep8 0 64 0 0 0 0 0 0 1 64 64 bulk 64 bulk 64 bulk out (2×) 64 bulk out (2×) 64 bulk in (2×) 64 bulk in (2×) 2 64 64 int 64 int 64 int out (2×) 64 bulk out (2×) 64 int in (2×) 64 bulk in (2×) 3 64 64 int 64 int 64 iso out (2×) 64 bulk out (2×) 64 iso in (2×) 64 bulk in (2×) Default High Speed Alternate Settings Table 7. Default High Speed Alternate Settings[2, 3] Alternate Setting 0 1 2 3 ep0 64 64 64 64 ep1out 0 512 bulk[4] 64 int 64 int ep1in 0 512 bulk[4] 64 int 64 int ep2 0 512 bulk out (2×) 512 int out (2×) 512 iso out (2×) ep4 0 512 bulk out (2×) 512 bulk out (2×) 512 bulk out (2×) ep6 0 512 bulk in (2×) 512 int in (2×) 512 iso in (2×) ep8 0 512 bulk in (2×) 512 bulk in (2×) 512 bulk in (2×) Notes 2. ‘0’ means ‘not implemented.’ 3. ‘2×’ means ‘double buffered.’ 4. Even though these buffers are 64 bytes, they are reported as 512 for USB 2.0 compliance. The user must never transfer packets larger than 64 bytes to EP1. Document Number: 001-04247 Rev. *J Page 12 of 40 CY7C68033/CY7C68034 External FIFO Interface same configuration to implement 100-ns timing on the NAND bus to support proper detection of all NAND Flash types. Architecture The NX2LP-Flex slave FIFO architecture has eight 512-byte blocks in the endpoint RAM that directly serve as FIFO memories, and are controlled by FIFO control signals (such as SLCS#, SLRD, SLWR, SLOE, PKTEND, and flags). In operation, some of the eight RAM blocks fill or empty from the SIE, while the others are connected to the I/O transfer logic. The transfer logic takes two forms: the GPIF for internally generated control signals or the slave FIFO interface for externally controlled transfers. Master/Slave Control Signals The NX2LP-Flex endpoint FIFOS are implemented as eight physically distinct 256 × 16 RAM blocks. The 8051/SIE can switch any of the RAM blocks between two domains, the USB (SIE) domain and the 8051-I/O Unit domain. This switching is done virtually instantaneously, giving essentially zero transfer time between ‘USB FIFOS’ and ‘Slave FIFOS’. Since they are physically the same memory, no bytes are actually transferred between buffers. At any time, some RAM blocks are filling/emptying with USB data under SIE control, while other RAM blocks are available to the 8051 and/or the I/O control unit. The RAM blocks operate as single-port in the USB domain and dual-port in the 8051-I/O domain. The blocks can be configured as single, double, triple, or quad buffered as previously shown. The I/O control unit implements either an internal-master (M for master) or external-master (S for Slave) interface. In master (M) mode, the GPIF internally controls FIFOADR[1:0] to select a FIFO. The two RDY pins can be used as flag inputs from an external FIFO or other logic if desired. The GPIF can be run from an internally derived clock (IFCLK), at a rate that transfers data up to 96 Megabytes/s (48 MHz IFCLK with 16-bit interface). In slave (S) mode, the NX2LP-Flex accepts an internally derived clock (IFCLK, max. frequency 48 MHz) and SLCS#, SLRD, SLWR, SLOE, PKTEND signals from external logic. Each endpoint can individually be selected for byte or word operation by an internal configuration bit and a Slave FIFO output enable signal SLOE enables data of the selected width. External logic must ensure that the output enable signal is inactive when writing data to a slave FIFO. The slave interface must operate asynchronously, where the SLRD and SLWR signals act directly as strobes, rather than a clock qualifier as in a synchronous mode. The signals SLRD, SLWR, SLOE and PKTEND are gated by the signal SLCS#. GPIF The GPIF is a flexible 8- or 16-bit parallel interface driven by a user-programmable finite state machine. It enables the NX2LP-Flex to perform local bus mastering and can implement a wide variety of protocols such as 8-bit NAND interface, printer parallel port, and Utopia. The default NAND firmware and boot logic uses GPIF functionality to interface with NAND Flash. The GPIF on the NX2LP-Flex features three programmable control outputs (CTL) and two general purpose ready inputs (RDY). The GPIF data bus width can be 8 or 16 bits. Because the default NAND firmware image implements an 8-bit data bus and up to eight chip enable pins on the GPIF ports, it is recommended that designs based upon the default firmware image also use an 8-bit data bus. Each GPIF vector defines the state of the control outputs and determines what state a ready input (or multiple inputs) must be before proceeding. The GPIF vector can be programmed to advance a FIFO to the next data value, advance an address, and so on. A sequence of the GPIF vectors make up a single waveform that is executed to perform the desired data move between the NX2LP-Flex and the external device. Three Control OUT Signals The NX2LP-Flex exposes three control signals, CTL[2:0]. CTLx waveform edges can be programmed to make transitions as fast as once per clock (20.8 ns using a 48 MHz clock). Two Ready IN Signals The 8051 programs the GPIF unit to test the RDY pins for GPIF branching. The 56-pin package brings out two signals, RDY[1:0]. Long Transfer Mode In GPIF master mode, the 8051 appropriately sets GPIF transaction count registers (GPIFTCB3, GPIFTCB2, GPIFTCB1, or GPIFTCB0) for unattended transfers of up to 232 transactions. The GPIF automatically throttles data flow to prevent underflow or overflow until the full number of requested transactions complete. The GPIF decrements the value in these registers to represent the current status of the transaction. ECC Generation[5] The NX2LP-Flex can calculate error correcting codes (ECCs) on data that passes across its GPIF or slave FIFO interfaces. There are two ECC configurations: ■ Two ECCs, each calculated over 256 bytes (SmartMedia Standard) ■ One ECC calculated over 512 bytes. GPIF and FIFO Clock Rates An 8051 register bit selects one of two frequencies for the internally supplied interface clock: 30 MHz and 48 MHz. A bit within the IFCONFIG register inverts the IFCLK signal. The default NAND firmware image implements a 48 MHz internally supplied interface clock. The NAND boot logic uses the The following two ECC configurations are selected by the ECCM bit. The ECC can correct any one-bit error or detect any two-bit error. Note 5. To use the ECC logic, the GPIF or Slave FIFO interface must be configured for byte-wide operation. Document Number: 001-04247 Rev. *J Page 13 of 40 CY7C68033/CY7C68034 ECCM = 0 Autopointer Access Two 3-byte ECCs, each calculated over a 256-byte block of data. This configuration conforms to the SmartMedia Standard and is used by both the NAND boot logic and default NAND firmware image. NX2LP-Flex provides two identical autopointers. They are similar to the internal 8051 data pointers, but with an additional feature: they can optionally increment after every memory access. Also, the autopointers can point to any NX2LP-Flex register or endpoint buffer space. When any value is written to ECCRESET and data is then passed across the GPIF or slave FIFO interface, the ECC for the first 256 bytes of data is calculated and stored in ECC1. The ECC for the next 256 bytes of data is stored in ECC2. After the second ECC is calculated, the values in the ECCx registers do not change until ECCRESET is written again, even if more data is subsequently passed across the interface. I2C Controller NX2LP has one I2C port that the 8051, once running uses to control external I2C devices. The I2C port operates in master mode only. The I2C post is disabled at startup and only available for use after the initial NAND access. ECCM = 1 I2C Port Pins One 3-byte ECC calculated over a 512-byte block of data. The I2C pins SCL and SDA must have external 2.2-k pull up resistors even if no EEPROM is connected to the NX2LP. When any value is written to ECCRESET and data is then passed across the GPIF or slave FIFO interface, the ECC for the first 512 bytes of data is calculated and stored in ECC1; ECC2 is unused. After the ECC is calculated, the value in ECC1 does not change until ECCRESET is written again, even if more data is subsequently passed across the interface Document Number: 001-04247 Rev. *J I2C Interface General-Purpose Access The 8051 can control peripherals connected to the I2C bus using the I2CTL and I2DATA registers. NX2LP provides I2C master control only and is never an I2C slave. Page 14 of 40 CY7C68033/CY7C68034 Pin Assignments Figure 9 and Figure 10 on page 16 identify all signals for the 56-pin NX2LP-Flex package. Three modes of operation are available for the NX2LP-Flex: Port mode, GPIF Master mode, and Slave FIFO mode. These modes define the signals on the right edge of each column in Figure 9. The right-most column details the signal functionality from the default NAND firmware image, which actually utilizes GPIF Master mode. The signals on the left edge of the ‘Port’ column are common to all modes of the NX2LP-Flex. The 8051 selects the interface mode using the IFCONFIG[1:0] register bits. Port mode is the power-on default configuration. Figure 10 on page 16 details the pinout of the 56-pin package and lists pin names for all modes of operation. Pin names with an asterisk (*) feature programmable polarity. Figure 9. Port and Signal Mapping Port GPIF Master PD7 PD6 PD5 PD4 PD3 PD2 PD1 PD0 PB7 PB6 PB5 PB4 PB3 PB2 PB1 PB0 XTALIN XTALOUT RESET# WAKEUP# SCL SDATA DPLUS DMINUS PA7 PA6 PA5 PA4 WU2/PA3 PA2 INT1#/PA1 INTO#/PA0 GPIO8 GPIO9 Document Number: 001-04247 Rev. *J FD[15] FD[14] FD[13] FD[12] FD[11] FD[10] FD[9] FD[8] FD[7] FD[6] FD[5] FD[4] FD[3] FD[2] FD[1] FD[0] RDY0 RDY1 CTL0 CTL1 CTL2 PA7 PA6 PA5 PA4 PA3/WU2 PA2 PA1/INT1# PA0/INT0# GPIO8 GPIO9 Slave FIFO FD[15] FD[14] FD[13] FD[12] FD[11] FD[10] FD[9] FD[8] FD[7] FD[6] FD[5] FD[4] FD[3] FD[2] FD[1] FD[0] SLRD SLWR FLAGA FLAGB FLAGC FLAGD/SLCS#/PA7 PKTEND FIFOADR1 FIFOADR0 PA3/WU2 SLOE PA1/INT1# PA0/INT0# GPIO8 GPIO9 Default NAND Firmware Use CE7#/GPIO7 CE6#/GPIO6 CE5#/GPIO5 CE4#/GPIO4 CE3#/GPIO3 CE2#/GPIO2 CE1# CE0# DD7 DD6 DD5 DD4 DD3 DD2 DD1 DD0 R_B1# R_B2# WE# RE0# RE1# GPIO1 GPIO0 WP_SW# WP_NF# LED2# LED1# ALE CLE GPIO8 GPIO9 Page 15 of 40 CY7C68033/CY7C68034 Figure 10. CY7C68033/CY7C68034 56-pin QFN Pin Assignment GND VCC GPIO9 GND PD7/FD15 PD6/FD14 PD5/FD13 PD4/FD12 PD3/FD11 PD2/FD10 PD1/FD9 PD0/FD8 *WAKEUP VCC 56 55 54 53 52 51 50 49 48 47 46 45 44 43 RDY0/*SLRD 1 42 RESET# RDY1/*SLWR 2 41 GND AVCC 3 40 PA7/*FLAGD/SLCS# XTALOUT 4 39 PA6/*PKTEND XTALIN 5 38 PA5/FIFOADR1 AGND 6 37 PA4/FIFOADR0 AVCC 7 36 PA3/*WU2 DPLUS 8 35 PA2/*SLOE DMINUS 9 34 PA1/INT1# AGND 10 33 PA0/INT0# VCC 11 32 VCC GND 12 31 CTL2/*FLAGC GPIO8 13 30 CTL1/*FLAGB RESERVED# 14 29 CTL0/*FLAGA 15 16 17 18 19 20 21 22 23 24 25 26 27 28 SCL SDATA VCC PB0/FD0 PB1/FD1 PB2/FD2 PB3/FD3 PB4/FD4 PB5/FD5 PB6/FD6 PB7/FD7 GND VCC GND Document Number: 001-04247 Rev. *J Page 16 of 40 CY7C68033/CY7C68034 Table 8. NX2LP-Flex Pin Descriptions [6] 56-pin QFN Pin Number Default Pin Name NAND Firmware Usage Pin Type Default State Description 9 DMINUS N/A I/O/Z Z USB D– Signal. Connect to the USB D– signal. 8 DPLUS N/A I/O/Z Z USB D+ Signal. Connect to the USB D+ signal. 42 RESET# N/A Input N/A Active LOW Reset. Resets the entire chip. See section Reset and Wakeup on page 9 for more details. 5 XTALIN N/A Input N/A Crystal Input. Connect this signal to a 24 MHz parallel-resonant, fundamental mode crystal and load capacitor to GND. It is also correct to drive XTALIN with an external 24 MHz square wave derived from another clock source. When driving from an external source, the driving signal should be a 3.3 V square wave. 4 XTALOUT N/A Output N/A Crystal Output. Connect this signal to a 24 MHz parallel-resonant, fundamental mode crystal and load capacitor to GND. If an external clock is used to drive XTALIN, leave this pin open. 54 GPIO9 GPIO9 O/Z 1 RDY0 or SLRD R_B1# Input N/A Multiplexed pin whose function is selected by IFCONFIG[1:0]. RDY0 is a GPIF input signal. SLRD is the input-only read strobe with programmable polarity (FIFOPINPOLAR[3]) for the slave FIFOs connected to FD[7:0] or FD[15:0]. R_B1# is a NAND Ready/Busy input signal. 2 RDY1 or SLWR R_B2# Input N/A Multiplexed pin whose function is selected by IFCONFIG[1:0]. RDY1 is a GPIF input signal. SLWR is the input-only write strobe with programmable polarity (FIFOPINPOLAR[2]) for the slave FIFOs connected to FD[7:0] or FD[15:0]. R_B2# is a NAND Ready/Busy input signal. 29 CTL0 or FLAGA WE# O/Z H Multiplexed pin whose function is selected by IFCONFIG[1:0]. CTL0 is a GPIF control output. FLAGA is a programmable slave-FIFO output status flag signal. Defaults to programmable for the FIFO selected by the FIFOADR[1:0] pins. WE# is the NAND write enable output signal. 30 CTL1 or FLAGB RE0# O/Z H Multiplexed pin whose function is selected by IFCONFIG[1:0]. CTL1 is a GPIF control output. FLAGB is a programmable slave-FIFO output status flag signal. Defaults to FULL for the FIFO selected by the FIFOADR[1:0] pins. RE0# is a NAND read enable output signal. 31 CTL2 or FLAGC RE1# O/Z H Multiplexed pin whose function is selected by IFCONFIG[1:0]. CTL2 is a GPIF control output. FLAGC is a programmable slave-FIFO output status flag signal. Defaults to EMPTY for the FIFO selected by the FIFOADR[1:0] pins. RE1# is a NAND read enable output signal. 12 MHz GPIO9 is a bidirectional I/O port pin. Note 6. Unused inputs should not be left floating. Tie either HIGH or LOW as appropriate. Outputs should only be pulled up or down to ensure signals at power up and in standby. Note also that no pins should be driven while the device is powered down. Document Number: 001-04247 Rev. *J Page 17 of 40 CY7C68033/CY7C68034 Table 8. NX2LP-Flex Pin Descriptions (continued)[6] 56-pin QFN Pin Number 13 Default Pin Name GPIO8 NAND Firmware Usage Pin Type Default State GPIO8 I/O/Z I Description GPIO8: is a bidirectional I/O port pin. 14 Reserved# N/A Input N/A 15 SCL N/A OD Z Clock for the I2C interface. Connect to VCC with a 2.2K resistor, even if no I2C peripheral is attached. Reserved. Connect to ground. 16 SDATA N/A OD Z Data for the I2C interface. Connect to VCC with a 2.2K resistor, even if no I2C peripheral is attached. 44 WAKEUP Unused Input N/A USB Wakeup. If the 8051 is in suspend, asserting this pin starts up the oscillator and interrupts the 8051 to allow it to exit the suspend mode. Holding WAKEUP asserted inhibits the EZ-USB chip from suspending. This pin has programmable polarity, controlled by WAKEUP[4]. Port A 33 PA0 or INT0# CLE I/O/Z I (PA0) Multiplexed pin whose function is selected by PORTACFG[0] PA0 is a bidirectional I/O port pin. INT0# is the active-LOW 8051 INT0 interrupt input signal, which is either edge triggered (IT0 = 1) or level triggered (IT0 = 0). CLE is the NAND Command Latch Enable signal. 34 PA1 or INT1# ALE I/O/Z I (PA1) Multiplexed pin whose function is selected by PORTACFG[1] PA1 is a bidirectional I/O port pin. INT1# is the active-LOW 8051 INT1 interrupt input signal, which is either edge triggered (IT1 = 1) or level triggered (IT1 = 0). ALE is the NAND Address Latch Enable signal. 35 PA2 or SLOE LED1# I/O/Z I (PA2) Multiplexed pin whose function is selected by IFCONFIG[1:0]. PA2 is a bidirectional I/O port pin. SLOE is an input-only output enable with programmable polarity (FIFOPINPOLAR[4]) for the slave FIFOs connected to FD[7:0] or FD[15:0]. LED1# is the data activity indicator LED sink pin. 36 PA3 or WU2 LED2# I/O/Z I (PA3) Multiplexed pin whose function is selected by WAKEUP[7] and OEA[3] PA3 is a bidirectional I/O port pin. WU2 is an alternate source for USB Wakeup, enabled by WU2EN bit (WAKEUP[1]) and polarity set by WU2POL (WAKEUP[4]). If the 8051 is in suspend and WU2EN = 1, a transition on this pin starts up the oscillator and interrupts the 8051 to allow it to exit the suspend mode. Asserting this pin inhibits the chip from suspending, if WU2EN = 1. LED2# is the chip activity indicator LED sink pin. 37 PA4 or FIFOADR0 WP_NF# I/O/Z I (PA4) Multiplexed pin whose function is selected by IFCONFIG[1:0]. PA4 is a bidirectional I/O port pin. FIFOADR0 is an input-only address select for the slave FIFOs connected to FD[7:0] or FD[15:0]. WP_NF# is the NAND write-protect control output signal. 38 PA5 or FIFOADR1 WP_SW# I/O/Z I (PA5) Multiplexed pin whose function is selected by IFCONFIG[1:0]. PA5 is a bidirectional I/O port pin. FIFOADR1 is an input-only address select for the slave FIFOs connected to FD[7:0] or FD[15:0]. WP_SW# is the NAND write-protect switch input signal. Document Number: 001-04247 Rev. *J Page 18 of 40 CY7C68033/CY7C68034 Table 8. NX2LP-Flex Pin Descriptions (continued)[6] 56-pin QFN Pin Number Default Pin Name NAND Firmware Usage Pin Type Default State Description 39 PA6 or PKTEND GPIO0 (Input) I/O/Z I (PA6) Multiplexed pin whose function is selected by the IFCONFIG[1:0] bits. PA6 is a bidirectional I/O port pin. PKTEND is an input used to commit the FIFO packet data to the endpoint and whose polarity is programmable via FIFOPINPOLAR[5]. GPIO1 is a general purpose I/O signal. 40 PA7 or FLAGD or SLCS# GPIO1 (Input) I/O/Z I (PA7) Multiplexed pin whose function is selected by the IFCONFIG[1:0] and PORTACFG[7] bits. PA7 is a bidirectional I/O port pin. FLAGD is a programmable slave-FIFO output status flag signal. SLCS# gates all other slave FIFO enable/strobes GPIO0 is a general purpose I/O signal. Port B 18 PB0 or FD[0] DD0 I/O/Z I (PB0) Multiplexed pin whose function is selected by IFCONFIG[1:0]. PB0 is a bidirectional I/O port pin. FD[0] is the bidirectional FIFO/GPIF data bus. DD0 is a bidirectional NAND data bus signal. 19 PB1 or FD[1] DD1 I/O/Z I (PB1) Multiplexed pin whose function is selected by IFCONFIG[1:0]. PB1 is a bidirectional I/O port pin. FD[1] is the bidirectional FIFO/GPIF data bus. DD1 is a bidirectional NAND data bus signal. 20 PB2 or FD[2] DD2 I/O/Z I (PB2) Multiplexed pin whose function is selected by IFCONFIG[1:0]. PB2 is a bidirectional I/O port pin. FD[2] is the bidirectional FIFO/GPIF data bus. DD2 is a bidirectional NAND data bus signal. 21 PB3 or FD[3] DD3 I/O/Z I (PB3) Multiplexed pin whose function is selected by IFCONFIG[1:0]. PB3 is a bidirectional I/O port pin. FD[3] is the bidirectional FIFO/GPIF data bus. DD3 is a bidirectional NAND data bus signal. 22 PB4 or FD[4] DD4 I/O/Z I (PB4) Multiplexed pin whose function is selected by IFCONFIG[1:0]. PB4 is a bidirectional I/O port pin. FD[4] is the bidirectional FIFO/GPIF data bus. DD4 is a bidirectional NAND data bus signal. 23 PB5 or FD[5] DD5 I/O/Z I (PB5) Multiplexed pin whose function is selected by IFCONFIG[1:0]. PB5 is a bidirectional I/O port pin. FD[5] is the bidirectional FIFO/GPIF data bus. DD5 is a bidirectional NAND data bus signal. 24 PB6 or FD[6] DD6 I/O/Z I (PB6) Multiplexed pin whose function is selected by IFCONFIG[1:0]. PB6 is a bidirectional I/O port pin. FD[6] is the bidirectional FIFO/GPIF data bus. DD6 is a bidirectional NAND data bus signal. 25 PB7 or FD[7] DD7 I/O/Z I (PB7) Multiplexed pin whose function is selected by IFCONFIG[1:0]. PB7 is a bidirectional I/O port pin. FD[7] is the bidirectional FIFO/GPIF data bus. DD7 is a bidirectional NAND data bus signal. PD0 or FD[8] CE0# I/O/Z I (PD0) Multiplexed pin whose function is selected by the IFCONFIG[1:0] and EPxFIFOCFG.0 (wordwide) bits. FD[8] is the bidirectional FIFO/GPIF data bus. CE0# is a NAND chip enable output signal. PORT D 45 Document Number: 001-04247 Rev. *J Page 19 of 40 CY7C68033/CY7C68034 Table 8. NX2LP-Flex Pin Descriptions (continued)[6] 56-pin QFN Pin Number Default Pin Name NAND Firmware Usage Pin Type Default State Description 46 PD1 or FD[9] CE1# I/O/Z I (PD1) Multiplexed pin whose function is selected by the IFCONFIG[1:0] and EPxFIFOCFG.0 (wordwide) bits. FD[9] is the bidirectional FIFO/GPIF data bus. CE1# is a NAND chip enable output signal. 47 PD2 or FD[10] CE2# or GPIO2 I/O/Z I (PD2) Multiplexed pin whose function is selected by the IFCONFIG[1:0] and EPxFIFOCFG.0 (wordwide) bits. FD[10] is the bidirectional FIFO/GPIF data bus. CE2# is a NAND chip enable output signal. GPIO2 is a general purpose I/O signal. 48 PD3 or FD[11] CE3# or GPIO3 I/O/Z I (PD3) Multiplexed pin whose function is selected by the IFCONFIG[1:0] and EPxFIFOCFG.0 (wordwide) bits. FD[11] is the bidirectional FIFO/GPIF data bus. CE3# is a NAND chip enable output signal. GPIO3 is a general purpose I/O signal. 49 PD4 or FD[12] CE4# or GPIO4 I/O/Z I (PD4) Multiplexed pin whose function is selected by the IFCONFIG[1:0] and EPxFIFOCFG.0 (wordwide) bits. FD[12] is the bidirectional FIFO/GPIF data bus. CE4# is a NAND chip enable output signal. GPIO4 is a general purpose I/O signal. 50 PD5 or FD[13] CE5# or GPIO5 I/O/Z I (PD5) Multiplexed pin whose function is selected by the IFCONFIG[1:0] and EPxFIFOCFG.0 (wordwide) bits. FD[13] is the bidirectional FIFO/GPIF data bus. CE5# is a NAND chip enable output signal. GPIO5 is a general purpose I/O signal. 51 PD6 or FD[14] CE6# or GPIO6 I/O/Z I (PD6) Multiplexed pin whose function is selected by the IFCONFIG[1:0] and EPxFIFOCFG.0 (wordwide) bits. FD[14] is the bidirectional FIFO/GPIF data bus. CE6# is a NAND chip enable output signal. GPIO6 is a general purpose I/O signal. 52 PD7 or FD[15] CE7# or GPIO7 I/O/Z I (PD7) Multiplexed pin whose function is selected by the IFCONFIG[1:0] and EPxFIFOCFG.0 (wordwide) bits. FD[15] is the bidirectional FIFO/GPIF data bus. CE7# is a NAND chip enable output signal. GPIO7 is a general purpose I/O signal. Power and Ground 3, 7 AVCC N/A Power N/A Analog VCC. Connect this pin to 3.3 V power source. This signal provides power to the analog section of the chip. 6, 10 AGND N/A Ground N/A Analog Ground. Connect to ground with as short a path as possible. 11, 17, VCC 27, 32, 43, 55 N/A Power N/A VCC. Connect to 3.3 V power source. 12, 26, GND 28, 41, 53, 56 N/A Ground N/A Ground. Document Number: 001-04247 Rev. *J Page 20 of 40 CY7C68033/CY7C68034 Register Summary NX2LP-Flex register bit definitions are described in the EZ-USB TRM in greater detail. Some registers that are listed here and in the TRM do not apply to the NX2LP-Flex. They are kept here for consistency reasons only. Registers that do not apply to the NX2LP-Flex should be left at their default power up values. Table 9. NX2LP-Flex Register Summary Hex Size E400 128 E480 128 E50D E600 1 E601 1 E602 1 E603 1 E604 1 E605 E606 E607 E608 1 1 1 1 E609 1 E60A 1 E60B 1 E60C 1 3 E610 1 E611 1 E612 E613 E614 E615 1 1 1 1 2 E618 1 E619 1 E61A 1 E61B 1 E61C 4 E620 1 E621 1 E622 1 E623 1 E624 1 E625 1 E626 1 E627 1 E628 1 Name Description b7 GPIF Waveform Memories WAVEDATA GPIF Waveform D7 Descriptor 0, 1, 2, 3 data reserved GENERAL CONFIGURATION GPCR2 General Purpose reserved Configuration Register 2 CPUCS CPU Control & Status 0 IFCONFIG Interface Configuration 1 (Ports, GPIF, slave FIFOs) [7] PINFLAGSAB Slave FIFO FLAGA and FLAGB3 FLAGB Pin Configuration [7] PINFLAGSCD Slave FIFO FLAGC and FLAGD3 FLAGD Pin Configuration FIFORESET [7] Restore FIFOS to default NAKALL state BREAKPT Breakpoint Control 0 BPADDRH Breakpoint Address H A15 BPADDRL Breakpoint Address L A7 UART230 230 Kbaud internally 0 generated ref. clock FIFOPINPOLAR [7] Slave FIFO Interface pins 0 polarity REVID Chip Revision rv7 [7] REVCTL Chip Revision Control UDMA GPIFHOLDAMOUNT MSTB Hold Time (for UDMA) reserved ENDPOINT CONFIGURATION EP1OUTCFG Endpoint 1-OUT Configuration EP1INCFG Endpoint 1-IN Configuration EP2CFG Endpoint 2 Configuration EP4CFG Endpoint 4 Configuration EP6CFG Endpoint 6 Configuration EP8CFG Endpoint 8 Configuration reserved EP2FIFOCFG [7] Endpoint 2/slave FIFO configuration EP4FIFOCFG [7] Endpoint 4/slave FIFO configuration [7] EP6FIFOCFG Endpoint 6/slave FIFO configuration [7] EP8FIFOCFG Endpoint 8/slave FIFO configuration reserved EP2AUTOINLENH [7] Endpoint 2 AUTOIN Packet Length H EP2AUTOINLENL [7] Endpoint 2 AUTOIN Packet Length L EP4AUTOINLENH [7] Endpoint 4 AUTOIN Packet Length H EP4AUTOINLENL [7] Endpoint 4 AUTOIN Packet Length L EP6AUTOINLENH [7] Endpoint 6 AUTOIN Packet Length H EP6AUTOINLEN L [7] Endpoint 6 AUTOIN Packet Length L EP8AUTOINLENH [7] Endpoint 8 AUTOIN Packet Length H EP8AUTOINLENL [7] Endpoint 8 AUTOIN Packet Length L ECCCFG ECC Configuration b6 b5 D6 D5 reserved reserved b4 D4 b3 D3 b2 b1 b0 Default Access D2 D1 D0 xxxxxxxx RW reserved reserved reserved 00000000 R 0 3048 MHz FULL_SPEE reserved D_ONLY PORTCSTB CLKSPD1 CLKSPD0 0 IFCLKPOL ASYNC CLKINV GSTATE CLKOE IFCFG1 8051RES IFCFG0 00000010 10000000 rrbbbbbr RW FLAGB2 FLAGB1 FLAGB0 FLAGA3 FLAGA2 FLAGA1 FLAGA0 00000000 RW FLAGD2 FLAGD1 FLAGD0 FLAGC3 FLAGC2 FLAGC1 FLAGC0 00000000 RW 0 0 0 EP3 EP2 EP1 EP0 xxxxxxxx W 0 A14 A6 0 0 A13 A5 0 0 A12 A4 0 BREAK A11 A3 0 BPPULSE A10 A2 0 BPEN A9 A1 230UART1 0 A8 A0 230UART0 00000000 xxxxxxxx xxxxxxxx 00000000 rrrrbbbr RW RW rrrrrrbb 0 PKTEND SLOE SLRD SLWR EF FF 00000000 rrbbbbbb rv6 rv5 rv4 rv3 rv2 rv1 rv0 R 0 0 0 0 0 0 dyn_out enh_pkt RevA 00000001 00000000 0 0 0 0 0 0 HOLDTIME1 HOLDTIME0 00000000 rrrrrrbb VALID 0 TYPE1 TYPE0 0 0 0 0 10100000 brbbrrrr VALID 0 TYPE1 TYPE0 0 0 0 0 10100000 brbbrrrr VALID VALID VALID VALID DIR DIR DIR DIR TYPE1 TYPE1 TYPE1 TYPE1 TYPE0 TYPE0 TYPE0 TYPE0 SIZE 0 SIZE 0 0 0 0 0 BUF1 0 BUF1 0 BUF0 0 BUF0 0 10100010 10100000 11100010 11100000 bbbbbrbb bbbbrrrr bbbbbrbb bbbbrrrr 0 INFM1 OEP1 AUTOOUT AUTOIN ZEROLENIN 0 WORDWIDE 00000101 rbbbbbrb 0 INFM1 OEP1 AUTOOUT AUTOIN ZEROLENIN 0 WORDWIDE 00000101 rbbbbbrb 0 INFM1 OEP1 AUTOOUT AUTOIN ZEROLENIN 0 WORDWIDE 00000101 rbbbbbrb 0 INFM1 OEP1 AUTOOUT AUTOIN ZEROLENIN 0 WORDWIDE 00000101 rbbbbbrb 0 0 0 0 0 PL10 PL9 PL8 00000010 rrrrrbbb PL7 PL6 PL5 PL4 PL3 PL2 PL1 PL0 00000000 RW 0 0 0 0 0 0 PL9 PL8 00000010 rrrrrrbb PL7 PL6 PL5 PL4 PL3 PL2 PL1 PL0 00000000 RW 0 0 0 0 0 PL10 PL9 PL8 00000010 rrrrrbbb PL7 PL6 PL5 PL4 PL3 PL2 PL1 PL0 00000000 RW 0 0 0 0 0 0 PL9 PL8 00000010 rrrrrrbb PL7 PL6 PL5 PL4 PL3 PL2 PL1 PL0 00000000 RW 0 0 0 0 0 0 0 ECCM 00000000 rrrrrrrb rrrrrrbb Note 7. The register can only be reset, it cannot be set. Document Number: 001-04247 Rev. *J Page 21 of 40 CY7C68033/CY7C68034 Table 9. NX2LP-Flex Register Summary (continued) Hex Size E629 E62A E62B E62C E62D E62E E62F E630 H.S. E630 F.S. E631 H.S. E631 F.S E632 H.S. E632 F.S E633 H.S. E633 F.S E634 H.S. E634 F.S E635 H.S. E635 F.S E636 H.S. E636 F.S E637 H.S. E637 F.S Name 1 1 1 1 1 1 1 1 ECCRESET ECC1B0 ECC1B1 ECC1B2 ECC2B0 ECC2B1 ECC2B2 EP2FIFOPFH [8] 1 EP2FIFOPFH [8] 1 EP2FIFOPFL [8] 1 EP2FIFOPFL [8] 1 EP4FIFOPFH [8] 1 EP4FIFOPFH [8] 1 EP4FIFOPFL [8] 1 EP4FIFOPFL [8] 1 EP6FIFOPFH [8] 1 EP6FIFOPFH [8] 1 EP6FIFOPFL [8] 1 EP6FIFOPFL [8] 1 EP8FIFOPFH [8] 1 EP8FIFOPFH [8] 1 EP8FIFOPFL [8] 1 [8] EP8FIFOPFL 8 E640 1 reserved EP2ISOINPKTS E641 1 EP4ISOINPKTS E642 1 EP6ISOINPKTS E643 1 EP8ISOINPKTS E644 4 E648 1 E649 7 E650 1 reserved INPKTEND [8] OUTPKTEND [8] INTERRUPTS EP2FIFOIE [8] E651 1 EP2FIFOIRQ [8, 9] E652 1 EP4FIFOIE [8] [8, 9] E653 1 EP4FIFOIRQ E654 1 EP6FIFOIE [8] E655 1 EP6FIFOIRQ [8, 9] [8] E656 1 EP8FIFOIE E657 1 EP8FIFOIRQ [8, 9] E658 1 IBNIE E659 1 IBNIRQ E65A 1 NAKIE [8] Description b7 b6 b2 b1 Default Access x LINE12 LINE4 COL2 LINE12 LINE4 COL2 IN:PKTS[1] OUT:PFC11 OUT:PFC11 x x LINE11 LINE10 LINE3 LINE2 COL1 COL0 LINE11 LINE10 LINE3 LINE2 COL1 COL0 IN:PKTS[0] 0 OUT:PFC10 OUT:PFC10 0 x LINE9 LINE1 LINE17 LINE9 LINE1 0 PFC9 x LINE8 LINE0 LINE16 LINE8 LINE0 0 PFC8 00000000 00000000 00000000 00000000 00000000 00000000 00000000 10001000 W R R R R R R bbbbbrbb PKTSTAT x LINE13 LINE5 COL3 LINE13 LINE5 COL3 IN:PKTS[2] OUT:PFC12 OUT:PFC12 PFC9 10001000 bbbbbrbb PFC7 PFC6 PFC5 PFC4 PFC3 PFC2 PFC1 IN:PKTS[2] OUT:PFC8 PFC0 00000000 RW IN:PKTS[1] OUT:PFC7 DECIS IN:PKTS[0] OUT:PFC6 PKTSTAT PFC5 PFC4 PFC3 PFC2 PFC1 PFC0 00000000 RW 0 0 PFC8 10001000 bbrbbrrb DECIS PKTSTAT 0 IN: PKTS[1] IN: PKTS[0] 0 OUT:PFC10 OUT:PFC9 OUT:PFC10 OUT:PFC9 0 0 PFC8 10001000 bbrbbrrb PFC7 PFC6 PFC5 ECC Reset ECC1 Byte 0 Address ECC1 Byte 1 Address ECC1 Byte 2 Address ECC2 Byte 0 Address ECC2 Byte 1 Address ECC2 Byte 2 Address Endpoint 2/slave FIFO Programmable Flag H Endpoint 2/slave FIFO Programmable Flag H Endpoint 2/slave FIFO Programmable Flag L Endpoint 2/slave FIFO Programmable Flag L Endpoint 4/slave FIFO Programmable Flag H Endpoint 4/slave FIFO Programmable Flag H Endpoint 4/slave FIFO Programmable Flag L Endpoint 4/slave FIFO Programmable Flag L Endpoint 6/slave FIFO Programmable Flag H Endpoint 6/slave FIFO Programmable Flag H Endpoint 6/slave FIFO Programmable Flag L Endpoint 6/slave FIFO Programmable Flag L Endpoint 8/slave FIFO Programmable Flag H Endpoint 8/slave FIFO Programmable Flag H Endpoint 8/slave FIFO Programmable Flag L Endpoint 8/slave FIFO Programmable Flag L x LINE15 LINE7 COL5 LINE15 LINE7 COL5 DECIS x LINE14 LINE6 COL4 LINE14 LINE6 COL4 PKTSTAT DECIS b5 b4 b3 b0 PFC4 PFC3 PFC2 PFC1 PFC0 00000000 RW IN: PKTS[1] IN: PKTS[0] PFC5 OUT:PFC7 OUT:PFC6 DECIS PKTSTAT IN:PKTS[2] OUT:PFC12 DECIS PKTSTAT OUT:PFC12 PFC4 PFC3 PFC2 PFC1 PFC0 00000000 RW IN:PKTS[1] IN:PKTS[0] 0 OUT:PFC11 OUT:PFC10 OUT:PFC11 OUT:PFC10 0 PFC9 PFC8 00001000 bbbbbrbb PFC9 bbbbbrbb PFC6 PFC5 PFC4 PFC3 PFC2 PFC1 IN:PKTS[2] OUT:PFC8 PFC0 00001000 PFC7 00000000 RW IN:PKTS[1] OUT:PFC7 DECIS IN:PKTS[0] OUT:PFC6 PKTSTAT PFC5 PFC4 PFC3 PFC2 PFC1 PFC0 00000000 RW 0 0 PFC8 00001000 bbrbbrrb DECIS PKTSTAT 0 IN: PKTS[1] IN: PKTS[0] 0 OUT:PFC10 OUT:PFC9 OUT:PFC10 OUT:PFC9 0 0 PFC8 00001000 bbrbbrrb PFC7 PFC6 PFC5 PFC4 PFC3 PFC2 PFC1 PFC0 00000000 RW IN: PKTS[1] IN: PKTS[0] PFC5 OUT:PFC7 OUT:PFC6 PFC4 PFC3 PFC2 PFC1 PFC0 00000000 RW EP2 (if ISO) IN Packets per frame (1–3) EP4 (if ISO) IN Packets per frame (1–3) EP6 (if ISO) IN Packets per frame (1–3) EP8 (if ISO) IN Packets per frame (1–3) AADJ 0 0 0 0 0 INPPF1 INPPF0 00000001 brrrrrbb AADJ 0 0 0 0 0 INPPF1 INPPF0 00000001 brrrrrrr AADJ 0 0 0 0 0 INPPF1 INPPF0 00000001 brrrrrbb AADJ 0 0 0 0 0 INPPF1 INPPF0 00000001 brrrrrrr Force IN Packet End Force OUT Packet End Skip Skip 0 0 0 0 0 0 EP3 EP3 EP2 EP2 EP1 EP1 EP0 EP0 xxxxxxxx xxxxxxxx W W Endpoint 2 slave FIFO Flag Interrupt Enable Endpoint 2 slave FIFO Flag Interrupt Request Endpoint 4 slave FIFO Flag Interrupt Enable Endpoint 4 slave FIFO Flag Interrupt Request Endpoint 6 slave FIFO Flag Interrupt Enable Endpoint 6 slave FIFO Flag Interrupt Request Endpoint 8 slave FIFO Flag Interrupt Enable Endpoint 8 slave FIFO Flag Interrupt Request IN-BULK-NAK Interrupt Enable IN-BULK-NAK interrupt Request Endpoint Ping-NAK/IBN Interrupt Enable 0 0 0 0 EDGEPF PF EF FF 00000000 RW 0 0 0 0 0 PF EF FF 00000000 rrrrrbbb 0 0 0 0 EDGEPF PF EF FF 00000000 RW 0 0 0 0 0 PF EF FF 00000000 rrrrrbbb 0 0 0 0 EDGEPF PF EF FF 00000000 RW 0 0 0 0 0 PF EF FF 00000000 rrrrrbbb 0 0 0 0 EDGEPF PF EF FF 00000000 RW 0 0 0 0 0 PF EF FF 00000000 rrrrrbbb 0 0 EP8 EP6 EP4 EP2 EP1 EP0 00000000 RW 0 0 EP8 EP6 EP4 EP2 EP1 EP0 00xxxxxx rrbbbbbb EP8 EP6 EP4 EP2 EP1 EP0 0 IBN 00000000 RW Notes 8. The register can only be reset, it cannot be set. 9. SFRs not part of the standard 8051 architecture. Document Number: 001-04247 Rev. *J Page 22 of 40 CY7C68033/CY7C68034 Table 9. NX2LP-Flex Register Summary (continued) Hex Size Name E65B 1 NAKIRQ [10] E65C 1 E65D 1 E65E 1 USBIE USBIRQ [10] EPIE E65F 1 EPIRQ [10] E660 1 E661 1 E662 1 [10] GPIFIE GPIFIRQ [10] USBERRIE E663 1 USBERRIRQ [10] E664 1 ERRCNTLIM E665 1 E666 1 CLRERRCNT INT2IVEC E667 1 INT4IVEC E668 1 E669 7 E670 1 INTSET-UP reserved INPUT/OUTPUT PORTACFG E671 1 PORTCCFG E672 1 PORTECFG E673 E677 E678 E679 E67A E67B 4 1 1 1 1 1 XTALINSRC reserved I2CS I2DAT I2CTL XAUTODAT1 E67C 1 XAUTODAT2 E680 E681 E682 E683 E684 E685 E686 E687 E688 1 1 1 1 1 1 1 1 2 E68A E68B E68C E68D 1 1 1 1 UDMA CRC UDMACRCH [10] UDMACRCL [10] UDMACRCQUALIFIER USB CONTROL USBCS SUSPEND WAKEUPCS TOGCTL USBFRAMEH USBFRAMEL MICROFRAME FNADDR reserved ENDPOINTS EP0BCH [10] EP0BCL [10] reserved EP1OUTBC E68E E68F E690 E691 E692 E694 E695 E696 E698 E699 1 1 1 1 2 1 1 2 1 1 reserved EP1INBC EP2BCH [10] EP2BCL [10] reserved EP4BCH [10] EP4BCL [10] reserved EP6BCH [10] EP6BCL [10] E67D 1 E67E 1 E67F 1 Description b7 b6 b5 b4 b3 b2 b1 b0 Default Access Endpoint Ping-NAK/IBN EP8 Interrupt Request USB Int Enables 0 USB Interrupt Requests 0 Endpoint Interrupt EP8 Enables Endpoint Interrupt EP8 Requests GPIF Interrupt Enable 0 GPIF Interrupt Request 0 USB Error Interrupt ISOEP8 Enables USB Error Interrupt ISOEP8 Requests USB Error counter and EC3 limit Clear Error Counter EC3:0 x Interrupt 2 (USB) 0 Autovector Interrupt 4 (slave FIFO & 1 GPIF) Autovector Interrupt 2&4 setup 0 EP6 EP4 EP2 EP1 EP0 0 IBN xxxxxx0x bbbbbbrb EP0ACK EP0ACK EP6 HSGRANT HSGRANT EP4 URES URES EP2 SUSP SUSP EP1OUT SUTOK SUTOK EP1IN SOF SOF EP0OUT SUDAV SUDAV EP0IN 00000000 0xxxxxxx 00000000 RW rbbbbbbb RW EP6 EP4 EP2 EP1OUT EP1IN EP0OUT EP0IN 0 RW 0 0 ISOEP6 0 0 ISOEP4 0 0 ISOEP2 0 0 0 0 0 0 GPIFWF GPIFWF 0 GPIFDONE 00000000 GPIFDONE 000000xx ERRLIMIT 00000000 RW RW RW ISOEP6 ISOEP4 ISOEP2 0 0 0 ERRLIMIT 0000000x bbbbrrrb EC2 EC1 EC0 LIMIT3 LIMIT2 LIMIT1 LIMIT0 xxxx0100 rrrrbbbb x I2V4 x I2V3 x I2V2 x I2V1 x I2V0 x 0 x 0 xxxxxxxx 00000000 W R 0 I4V3 I4V2 I4V1 I4V0 0 0 10000000 R 0 0 0 AV2EN 0 INT4SRC AV4EN 00000000 RW I/O PORTA Alternate Configuration I/O PORTC Alternate Configuration I/O PORTE Alternate Configuration XTALIN Clock Source FLAGD SLCS 0 0 0 0 INT1 INT0 00000000 RW GPIFA7 GPIFA6 GPIFA5 GPIFA4 GPIFA3 GPIFA2 GPIFA1 GPIFA0 00000000 RW GPIFA8 T2EX INT6 RXD1OUT RXD0OUT T2OUT T1OUT T0OUT 00000000 RW 0 0 0 0 0 0 0 EXTCLK 00000000 rrrrrrrb I2C Bus Control & Status I2C Bus Data I2C Bus Control Autoptr1 MOVX access, when APTREN=1 Autoptr2 MOVX access, when APTREN=1 START d7 0 D7 STOP d6 0 D6 LASTRD d5 0 D5 ID1 d4 0 D4 ID0 d3 0 D3 BERR d2 0 D2 ACK d1 STOPIE D1 DONE d0 400kHz D0 000xx000 xxxxxxxx 00000000 xxxxxxxx bbbrrrrr RW RW RW D7 D6 D5 D4 D3 D2 D1 D0 xxxxxxxx RW UDMA CRC MSB UDMA CRC LSB UDMA CRC Qualifier CRC15 CRC7 QENABLE CRC14 CRC6 0 CRC13 CRC5 0 CRC12 CRC4 0 CRC11 CRC3 QSTATE CRC10 CRC2 QSIGNAL2 CRC9 CRC1 QSIGNAL1 CRC8 CRC0 QSIGNAL0 01001010 10111010 00000000 RW RW brrrbbbb USB Control & Status Put chip into suspend Wakeup Control & Status Toggle Control USB Frame count H USB Frame count L Microframe count, 0–7 USB Function address HSM x WU2 Q 0 FC7 0 0 0 x WU S 0 FC6 0 FA6 0 x WU2POL R 0 FC5 0 FA5 0 x WUPOL I/O 0 FC4 0 FA4 DISCON x 0 EP3 0 FC3 0 FA3 NOSYNSOF x DPEN EP2 FC10 FC2 MF2 FA2 RENUM x WU2EN EP1 FC9 FC1 MF1 FA1 SIGRSUME x WUEN EP0 FC8 FC0 MF0 FA0 x0000000 xxxxxxxx xx000101 x0000000 00000xxx xxxxxxxx 00000xxx 0xxxxxxx rrrrbbbb W bbbbrbbb rrrbbbbb R R R R Endpoint 0 Byte Count H (BC15) Endpoint 0 Byte Count L (BC7) (BC14) BC6 (BC13) BC5 (BC12) BC4 (BC11) BC3 (BC10) BC2 (BC9) BC1 (BC8) BC0 xxxxxxxx xxxxxxxx RW RW Endpoint 1 OUT Byte Count BC6 BC5 BC4 BC3 BC2 BC1 BC0 0xxxxxxx RW Endpoint 1 IN Byte Count 0 Endpoint 2 Byte Count H 0 Endpoint 2 Byte Count L BC7/SKIP BC6 0 BC6 BC5 0 BC5 BC4 0 BC4 BC3 0 BC3 BC2 BC10 BC2 BC1 BC9 BC1 BC0 BC8 BC0 0xxxxxxx 00000xxx xxxxxxxx RW RW RW Endpoint 4 Byte Count H 0 Endpoint 4 Byte Count L BC7/SKIP 0 BC6 0 BC5 0 BC4 0 BC3 0 BC2 BC9 BC1 BC8 BC0 000000xx xxxxxxxx RW RW Endpoint 6 Byte Count H 0 Endpoint 6 Byte Count L BC7/SKIP 0 BC6 0 BC5 0 BC4 0 BC3 BC10 BC2 BC9 BC1 BC8 BC0 00000xxx xxxxxxxx RW RW 0 Note 10. The register can only be reset, it cannot be set. Document Number: 001-04247 Rev. *J Page 23 of 40 CY7C68033/CY7C68034 Table 9. NX2LP-Flex Register Summary (continued) Hex Size E69A E69C E69D E69E E6A0 Name 2 1 1 2 1 reserved EP8BCH [11] EP8BCL [11] reserved EP0CS E6A1 1 EP1OUTCS E6A2 1 EP1INCS E6A3 1 EP2CS E6A4 1 EP4CS E6A5 1 EP6CS E6A6 1 EP8CS E6A7 1 EP2FIFOFLGS E6A8 1 EP4FIFOFLGS E6A9 1 EP6FIFOFLGS E6AA 1 EP8FIFOFLGS E6AB 1 EP2FIFOBCH E6AC 1 EP2FIFOBCL E6AD 1 EP4FIFOBCH E6AE 1 EP4FIFOBCL E6AF 1 EP6FIFOBCH E6B0 1 EP6FIFOBCL E6B1 1 EP8FIFOBCH E6B2 1 EP8FIFOBCL E6B3 1 SUDPTRH E6B4 1 SUDPTRL E6B5 1 SUDPTRCTL 2 E6B8 8 reserved SET-UPDAT E6C0 1 E6C1 1 GPIF GPIFWFSELECT GPIFIDLECS E6C2 E6C3 E6C4 E6C5 1 1 1 1 E6C6 1 GPIFIDLECTL GPIFCTLCFG GPIFADRH [11] GPIFADRL [11] FLOWSTATE FLOWSTATE E6C7 1 FLOWLOGIC Description b7 b6 b5 b4 b3 b2 b1 b0 Default Access Endpoint 8 Byte Count H 0 Endpoint 8 Byte Count L BC7/SKIP 0 BC6 0 BC5 0 BC4 0 BC3 0 BC2 BC9 BC1 BC8 BC0 000000xx xxxxxxxx RW RW Endpoint 0 Control and Status Endpoint 1 OUT Control and Status Endpoint 1 IN Control and Status Endpoint 2 Control and Status Endpoint 4 Control and Status Endpoint 6 Control and Status Endpoint 8 Control and Status Endpoint 2 slave FIFO Flags Endpoint 4 slave FIFO Flags Endpoint 6 slave FIFO Flags Endpoint 8 slave FIFO Flags Endpoint 2 slave FIFO total byte count H Endpoint 2 slave FIFO total byte count L Endpoint 4 slave FIFO total byte count H Endpoint 4 slave FIFO total byte count L Endpoint 6 slave FIFO total byte count H Endpoint 6 slave FIFO total byte count L Endpoint 8 slave FIFO total byte count H Endpoint 8 slave FIFO total byte count L Setup Data Pointer high address byte Setup Data Pointer low address byte Setup Data Pointer Auto Mode HSNAK 0 0 0 0 0 BUSY STALL 10000000 bbbbbbrb 0 0 0 0 0 0 BUSY STALL 00000000 bbbbbbrb 0 0 0 0 0 0 BUSY STALL 00000000 bbbbbbrb 0 NPAK2 NPAK1 NPAK0 FULL EMPTY 0 STALL 00101000 rrrrrrrb 0 0 NPAK1 NPAK0 FULL EMPTY 0 STALL 00101000 rrrrrrrb 0 NPAK2 NPAK1 NPAK0 FULL EMPTY 0 STALL 00000100 rrrrrrrb 0 0 NPAK1 NPAK0 FULL EMPTY 0 STALL 00000100 rrrrrrrb 0 0 0 0 0 PF EF FF 00000010 R 0 0 0 0 0 PF EF FF 00000010 R 0 0 0 0 0 PF EF FF 00000110 R 0 0 0 0 0 PF EF FF 00000110 R 0 0 0 BC12 BC11 BC10 BC9 BC8 00000000 R BC7 BC6 BC5 BC4 BC3 BC2 BC1 BC0 00000000 R 0 0 0 0 0 BC10 BC9 BC8 00000000 R BC7 BC6 BC5 BC4 BC3 BC2 BC1 BC0 00000000 R 0 0 0 0 BC11 BC10 BC9 BC8 00000000 R BC7 BC6 BC5 BC4 BC3 BC2 BC1 BC0 00000000 R 0 0 0 0 0 BC10 BC9 BC8 00000000 R BC7 BC6 BC5 BC4 BC3 BC2 BC1 BC0 00000000 R A15 A14 A13 A12 A11 A10 A9 A8 xxxxxxxx RW A7 A6 A5 A4 A3 A2 A1 0 xxxxxxx0 bbbbbbbr 0 0 0 0 0 0 0 SDPAUTO 00000001 RW 8 bytes of setup data SET-UPDAT[0] = bmRequestType SET-UPDAT[1] = bmRequest SET-UPDAT[2:3] = wValue SET-UPDAT[4:5] = wIndex SET-UPDAT[6:7] = wLength D7 D6 D5 D4 D3 D2 D1 D0 xxxxxxxx R Waveform Selector GPIF Done, GPIF IDLE drive mode Inactive Bus, CTL states CTL Drive Type GPIF Address H GPIF Address L SINGLEWR1 SINGLEWR0 SINGLERD1 SINGLERD0 FIFOWR1 DONE 0 0 0 0 FIFOWR0 0 FIFORD1 0 FIFORD0 IDLEDRV 11100100 10000000 RW RW 0 TRICTL 0 GPIFA7 0 0 0 GPIFA6 CTL5 CTL5 0 GPIFA5 CTL4 CTL4 0 GPIFA4 CTL3 CTL3 0 GPIFA3 CTL2 CTL2 0 GPIFA2 CTL1 CTL1 0 GPIFA1 CTL0 CTL0 GPIFA8 GPIFA0 11111111 00000000 00000000 00000000 RW RW RW RW Flowstate Enable and Selector Flowstate Logic FSE 0 0 0 0 FS2 FS1 FS0 00000000 brrrrbbb LFUNC1 LFUNC0 TERMA2 TERMA1 TERMA0 TERMB2 TERMB1 TERMB0 00000000 RW Note 11. The register can only be reset, it cannot be set. Document Number: 001-04247 Rev. *J Page 24 of 40 CY7C68033/CY7C68034 Table 9. NX2LP-Flex Register Summary (continued) Hex Size Name E6C8 1 FLOWEQ0CTL E6C9 1 FLOWEQ1CTL E6CA 1 FLOWHOLDOFF E6CB 1 FLOWSTB E6CC 1 FLOWSTBEDGE E6CD 1 E6CE 1 FLOWSTBPERIOD GPIFTCB3 [12] E6CF 1 GPIFTCB2 [12] E6D0 1 GPIFTCB1 [12] E6D1 1 [12] GPIFTCB0 Description CTL-Pin States in Flowstate (when Logic = 0) CTL-Pin States in Flowstate (when Logic = 1) Holdoff Configuration b7 b6 CTL0E3 CTL0E2 CTL0E1 / CTL5 CTL0E0 / CTL4 CTL3 CTL2 CTL1 CTL0 00000000 RW CTL0E3 CTL0E2 CTL0E1 / CTL5 CTL0E0 / CTL4 CTL3 CTL2 CTL1 CTL0 00000000 RW b4 b3 HOCTL2 HOCTL1 HOCTL0 00010010 RW MSTB2 MSTB1 MSTB0 00100000 RW HOPERIOD3 HOPERIOD2 HOPERIOD1 HOPERIOD HOSTATE 0 SLAVE RDYASYNC CTLTOGL SUSTAIN 0 Flowstate Strobe Configuration Flowstate Rising/Falling 0 Edge Configuration Master-Strobe Half-Period D7 GPIF Transaction Count TC31 Byte 3 GPIF Transaction Count TC23 Byte 2 GPIF Transaction Count TC15 Byte 1 GPIF Transaction Count TC7 Byte 0 b2 b1 b0 E6D3 E6D4 E6DA E6DB E6DC E6E2 E6E3 E6E4 E6EA E6EB E6EC E6F0 E6F1 E6F2 E6F3 E6F4 E6F5 E6F6 E740 E780 E7C0 Default Access 0 0 0 0 0 FALLING RISING 00000001 rrrrrrbb D6 TC30 D5 TC29 D4 TC28 D3 TC27 D2 TC26 D1 TC25 D0 TC24 00000010 00000000 RW RW TC22 TC21 TC20 TC19 TC18 TC17 TC16 00000000 RW TC14 TC13 TC12 TC11 TC10 TC9 TC8 00000000 RW TC6 TC5 TC4 TC3 TC2 TC1 TC0 00000001 RW 00000000 RW 2 E6D2 reserved reserved reserved 1 EP2GPIFFLGSEL [12] Endpoint 2 GPIF Flag select 1 EP2GPIFPFSTOP Endpoint 2 GPIF stop transaction on prog. flag [12] 1 EP2GPIFTRIG Endpoint 2 GPIF Trigger 3 reserved reserved reserved 1 EP4GPIFFLGSEL [12] Endpoint 4 GPIF Flag select 1 EP4GPIFPFSTOP Endpoint 4 GPIF stop transaction on GPIF Flag [12] 1 EP4GPIFTRIG Endpoint 4 GPIF Trigger 3 reserved reserved reserved 1 EP6GPIFFLGSEL [12] Endpoint 6 GPIF Flag select 1 EP6GPIFPFSTOP Endpoint 6 GPIF stop transaction on prog. flag [12] 1 EP6GPIFTRIG Endpoint 6 GPIF Trigger 3 reserved reserved reserved 1 EP8GPIFFLGSEL [12] Endpoint 8 GPIF Flag select 1 EP8GPIFPFSTOP Endpoint 8 GPIF stop transaction on prog. flag 1 EP8GPIFTRIG [12] Endpoint 8 GPIF Trigger 3 reserved 1 XGPIFSGLDATH GPIF Data H (16-bit mode only) 1 XGPIFSGLDATLX Read/Write GPIF Data L & trigger transaction 1 XGPIFSGLDATLNOX Read GPIF Data L, no transaction trigger 1 GPIFREADYCFG Internal RDY, Sync/Async, RDY pin states 1 GPIFREADYSTAT GPIF Ready Status 1 GPIFABORT Abort GPIF Waveforms 2 reserved ENDPOINT BUFFERS 64 EP0BUF EP0-IN/-OUT buffer 64 EP10UTBUF EP1-OUT buffer 64 EP1INBUF EP1-IN buffer 2048 reserved b5 0 0 1 0 0 0 0 FS1 FS0 00000000 RW 0 0 0 0 0 0 0 FIFO2FLAG 00000000 RW x x x x x x x x xxxxxxxx W 0 0 0 0 0 0 FS1 FS0 00000000 RW 0 0 0 0 0 0 0 FIFO4FLAG 00000000 RW x x x x x x x x xxxxxxxx W 0 0 0 0 0 0 FS1 FS0 00000000 RW 0 0 0 0 0 0 0 FIFO6FLAG 00000000 RW x x x x x x x x xxxxxxxx W 0 0 0 0 0 0 FS1 FS0 00000000 RW 0 0 0 0 0 0 0 FIFO8FLAG 00000000 RW x x x x x x x x xxxxxxxx W D15 D14 D13 D12 D11 D10 D9 D8 xxxxxxxx RW D7 D6 D5 D4 D3 D2 D1 D0 xxxxxxxx RW D7 D6 D5 D4 D3 D2 D1 D0 xxxxxxxx R INTRDY SAS TCXRDY5 0 0 0 0 0 00000000 bbbrrrrr 0 x 0 x RDY5 x RDY4 x RDY3 x RDY2 x RDY1 x RDY0 x 00xxxxxx xxxxxxxx R W D7 D7 D7 D6 D6 D6 D5 D5 D5 D4 D4 D4 D3 D3 D3 D2 D2 D2 D1 D1 D1 D0 D0 D0 xxxxxxxx xxxxxxxx xxxxxxxx RW RW RW RW Note 12. The register can only be reset, it cannot be set. Document Number: 001-04247 Rev. *J Page 25 of 40 CY7C68033/CY7C68034 Table 9. NX2LP-Flex Register Summary (continued) Hex Size Name F000 1024 EP2FIFOBUF F400 512 EP4FIFOBUF F600 512 reserved F800 1024 EP6FIFOBUF Description 8A 8B 8C 8D 8E 8F 90 91 92 1 1 1 1 1 1 1 1 1 93 98 5 1 99 9A 9B 9C 9D 9E 9F A0 A1 A2 A3 A8 1 1 1 1 1 1 1 1 1 1 5 1 A9 AA 1 1 AB 1 AC 1 AD AF B0 B1 2 1 1 1 B2 B3 B4 B5 B6 B7 1 1 1 1 1 1 b3 b2 b1 b0 Default Access D3 D2 D1 D0 xxxxxxxx RW D6 D5 D4 D3 D2 D1 D0 xxxxxxxx RW 512/1024-byte EP 6/slave D7 FIFO buffer (IN or OUT) 512 byte EP 8/slave FIFO D7 buffer (IN or OUT) D6 D5 D4 D3 D2 D1 D0 xxxxxxxx RW D6 D5 D4 D3 D2 D1 D0 xxxxxxxx RW 0 DISCON 0 0 0 0 0 400 kHz xxxxxxxx[14] n/a D7 D7 A7 A15 A7 A15 0 SMOD0 TF1 D6 D6 A6 A14 A6 A14 0 x TR1 D5 D5 A5 A13 A5 A13 0 1 TF0 D4 D4 A4 A12 A4 A12 0 1 TR0 D3 D3 A3 A11 A3 A11 0 x IE1 D2 D2 A2 A10 A2 A10 0 x IT1 D1 D1 A1 A9 A1 A9 0 x IE0 D0 D0 A0 A8 A0 A8 SEL IDLE IT0 xxxxxxxx 00000111 00000000 00000000 00000000 00000000 00000000 00110000 00000000 RW RW RW RW RW RW RW RW RW GATE CT M1 M0 GATE CT M1 M0 00000000 RW D7 D7 D15 D15 x D6 D6 D14 D14 x D5 D5 D13 D13 T2M D4 D4 D12 D12 T1M D3 D3 D11 D11 T0M D2 D2 D10 D10 MD2 D1 D1 D9 D9 MD1 D0 D0 D8 D8 MD0 00000000 00000000 00000000 00000000 00000001 RW RW RW RW RW D7 IE5 A15 D6 IE4 A14 D5 I²CINT A13 D4 USBNT A12 D3 1 A11 D2 0 A10 D1 0 A9 D0 0 A8 xxxxxxxx 00001000 00000000 RW RW RW SM0_0 SM1_0 SM2_0 REN_0 TB8_0 RB8_0 TI_0 RI_0 00000000 RW D7 A15 A7 D6 A14 A6 D5 A13 A5 D4 A12 A4 D3 A11 A3 D2 A10 A2 D1 A9 A1 D0 A8 A0 00000000 00000000 00000000 RW RW RW A15 A7 A14 A6 A13 A5 A12 A4 A11 A3 A10 A2 A9 A1 A8 A0 00000000 00000000 RW RW D7 x x D6 x x D5 x x D4 x x D3 x x D2 x x D1 x x D0 x x xxxxxxxx xxxxxxxx xxxxxxxx RW W W EA ES1 ET2 ES0 ET1 EX1 ET0 EX0 00000000 RW EP8F EP8E EP6F EP6E EP4F EP4E EP2F EP2E 01011010 R 0 EP4PF EP4EF EP4FF 0 EP2PF EP2EF EP2FF 00100010 R 0 EP8PF EP8EF EP8FF 0 EP6PF EP6EF EP6FF 01100110 R 0 D7 D7 0 D6 D6 0 D5 D5 0 D4 D4 0 D3 D3 APTR2INC D2 D2 APTR1INC D1 D1 APTREN D0 D0 00000110 xxxxxxxx xxxxxxxx RW RW RW D7 D7 D7 D7 D7 D6 D6 D6 D6 D6 D5 D5 D5 D5 D5 D4 D4 D4 D4 D4 D3 D3 D3 D3 D3 D2 D2 D2 D2 D2 D1 D1 D1 D1 D1 D0 D0 D0 D0 D0 00000000 00000000 00000000 00000000 00000000 RW RW RW RW RW reserved I²C Configuration Byte Special Function Registers (SFRs) IOA [13] Port A (bit addressable) SP Stack Pointer DPL0 Data Pointer 0 L DPH0 Data Pointer 0 H DPL1 [13] Data Pointer 1 L DPH1 [13] Data Pointer 1 H DPS [13] Data Pointer 0/1 select PCON Power Control TCON Timer/Counter Control (bit addressable) TMOD Timer/Counter Mode Control TL0 Timer 0 reload L TL1 Timer 1 reload L TH0 Timer 0 reload H TH1 Timer 1 reload H CKCON [13] Clock Control reserved IOB [13] Port B (bit addressable) EXIF [13] External Interrupt Flag(s) MPAGE [13] Upper Addr Byte of MOVX using @R0/@R1 reserved SCON0 Serial Port 0 Control (bit addressable) SBUF0 Serial Port 0 Data Buffer [13] AUTOPTRH1 Autopointer 1 Address H AUTOPTRL1 [13] Autopointer 1 Address L reserved AUTOPTRH2 [13] Autopointer 2 Address H AUTOPTRL2 [13] Autopointer 2 Address L reserved IOC [13] Port C (bit addressable) INT2CLR [13] Interrupt 2 clear INT4CLR [13] Interrupt 4 clear reserved IE Interrupt Enable (bit addressable) reserved [13] EP2468STAT Endpoint 2,4,6,8 status flags [13] EP24FIFOFLGS Endpoint 2,4 slave FIFO status flags EP68FIFOFLGS [13] Endpoint 6,8 slave FIFO status flags reserved AUTOPTRSET-UP [13] Autopointer 1&2 setup IOD [13] Port D (bit addressable) IOE [13] Port E (NOT bit addressable) OEA [13] Port A Output Enable OEB [13] Port B Output Enable OEC [13] Port C Output Enable [13] OED Port D Output Enable OEE [13] Port E Output Enable reserved 1 b4 D4 FE00 512 xxxx 89 b5 D5 EP8FIFOBUF 1 1 1 1 1 1 1 1 1 b6 D6 FC00 512 80 81 82 83 84 85 86 87 88 b7 512/1024-byte EP 2/slave D7 FIFO buffer (IN or OUT) 512 byte EP 4/slave FIFO D7 buffer (IN or OUT) Notes 13. SFRs not part of the standard 8051 architecture. 14. If no NAND is detected by the SIE then the default is 00000000. Document Number: 001-04247 Rev. *J Page 26 of 40 CY7C68033/CY7C68034 Table 9. NX2LP-Flex Register Summary (continued) Hex Size Name B8 1 IP B9 BA 1 1 reserved EP01STAT [15] [15, 16] BB 1 GPIFTRIG BC BD 1 1 reserved GPIFSGLDATH [15] BE BF 1 1 C0 1 GPIFSGLDATLX [15] GPIFSGLDAT LNOX [15] SCON1 [15] [15] C1 C2 C8 1 6 1 SBUF1 reserved T2CON C9 CA 1 1 reserved RCAP2L CB 1 RCAP2H CC CD CE D0 1 1 2 1 TL2 TH2 reserved PSW D1 D8 D9 E0 7 1 7 1 reserved EICON [15] reserved ACC E1 E8 7 1 reserved EIE [15] E9 F0 F1 F8 7 1 7 1 reserved B reserved EIP [15] F9 7 reserved Description b7 b6 b5 b4 b3 b2 b1 Interrupt Priority (bit addressable) 1 PS1 PT2 PS0 PT1 PX1 PT0 Endpoint 0&1 Status 0 0 0 0 0 EP1INBSY Endpoint 2,4,6,8 GPIF slave FIFO Trigger DONE 0 0 0 0 GPIF Data H (16-bit mode D15 only) GPIF Data L w/Trigger D7 GPIF Data L w/No Trigger D7 D14 D13 D12 D6 D6 D5 D5 D4 D4 Serial Port 1 Control (bit SM0_1 addressable) Serial Port 1 Data Buffer D7 SM1_1 SM2_1 D6 Timer/Counter 2 Control (bit addressable) TF2 Capture for Timer 2, auto-reload, up-counter Capture for Timer 2, auto-reload, up-counter Timer 2 reload L Timer 2 reload H b0 Default Access 10000000 RW 00000000 R RW EP1OUTBS EP0BSY Y EP1 EP0 10000xxx brrrrbbb D11 D10 D9 D8 xxxxxxxx RW D3 D3 D2 D2 D1 D1 D0 D0 xxxxxxxx xxxxxxxx RW R REN_1 TB8_1 RB8_1 TI_1 RI_1 00000000 RW D5 D4 D3 D2 D1 D0 00000000 RW EXF2 RCLK TCLK EXEN2 TR2 CT2 CPRL2 00000000 RW D7 D6 D5 D4 D3 D2 D1 D0 00000000 RW D7 D6 D5 D4 D3 D2 D1 D0 00000000 RW D7 D15 D6 D14 D5 D13 D4 D12 D3 D11 D2 D10 D1 D9 D0 D8 00000000 00000000 RW RW Program Status Word (bit CY addressable) AC F0 RS1 RS0 OV F1 P 00000000 RW External Interrupt Control SMOD1 1 ERESI RESI INT6 0 0 0 01000000 RW Accumulator (bit addressable) D7 D6 D5 D4 D3 D2 D1 D0 00000000 RW External Interrupt Enable(s) 1 1 1 EX6 EX5 EX4 EI²C EUSB 11100000 RW B (bit addressable) D7 D6 D5 D4 D3 D2 D1 D0 00000000 RW 1 1 PX6 PX5 PX4 PI²C PUSB 11100000 RW External Interrupt Priority 1 Control PX0 R = all bits read-only W = all bits write-only r = read-only bit w = write-only bit b = both read/write bit Notes 15. SFRs not part of the standard 8051 architecture. 16. If no NAND is detected by the SIE then the default is 00000000. Document Number: 001-04247 Rev. *J Page 27 of 40 CY7C68033/CY7C68034 Absolute Maximum Ratings Power Dissipation .................................................... 300 mW Exceeding maximum ratings may impair the useful life of the device. These user guidelines are not tested. Static Discharge Voltage ......................................... > 2000 V Max Output Current, per I/O port ................................ 10 mA Storage Temperature ............................... –65 °C to +150 °C Operating Conditions Ambient Temperature with Power Supplied ...................................... 0 °C to +70 °C TA (Ambient Temperature Under Bias) .......... 0 °C to +70 °C Supply Voltage to Ground Potential .............–0.5 V to +4.0 V Supply Voltage .........................................+3.00 V to +3.60 V V[17] Ground Voltage ................................................................ 0 V DC Voltage Applied to Outputs in High Z State ...................... –0.5 V to VCC + 0.5 V FOSC (Oscillator or Crystal Frequency) ............. 24 MHz ± 100 ppm (Parallel Resonant) DC Input Voltage to any Input Pin ....................... +5.25 DC Characteristics Parameter Description Conditions Min Typ Max Unit VCC Supply voltage 3.00 3.3 3.60 V VCC ramp up 0 to 3.3 V 200 – – s VIH Input HIGH voltage 2 – 5.25 V VIL Input LOW voltage –0.5 – 0.8 V VIH_X Crystal input HIGH voltage 2 – 5.25 V VIL_X Crystal input LOW voltage –0.5 – 0.8 V II Input leakage current 0< VIN < VCC – – ±10 A VOH Output voltage HIGH IOUT = 4 mA 2.4 – – V VOL Output LOW voltage IOUT = –4 mA – – 0.4 V IOH Output current HIGH – – 4 mA IOL Output current LOW – – 4 mA CIN Input pin capacitance Except D+/D– – – 10 pF D+/D– – – 15 pF ISUSP Suspend current Connected – 300 380 [18] A CY7C68034 Disconnected – 100 150 [18] A Suspend current Connected – 0.5 1.2 [18] mA CY7C68033 Disconnected – 0.3 1.0 [18] mA ICC Supply current 8051 running, connected to USB HS – 43 – mA 8051 running, connected to USB FS – 35 – mA IUNCONFIG Unconfigured current Before bMaxPower granted by host – 43 – mA TRESET Reset time after valid power VCC min = 3.0 V Pin reset after powered on 5.0 – – ms 200 – – s USB Transceiver USB 2.0-compliant in full and high speed modes. AC Electrical Characteristics USB Transceiver USB 2.0-compliant in full and high speed modes. Notes 17. Applying power to I/O pins when the chip is not powered is not recommended. 18. .Measured at Max VCC, 25 °C. Document Number: 001-04247 Rev. *J Page 28 of 40 CY7C68033/CY7C68034 Slave FIFO Asynchronous Read Figure 11. Slave FIFO Asynchronous Read Timing Diagram [19] tRDpwh SLRD tRDpwl FLAGS tXFD tXFLG DATA N+1 N tOEon tOEoff SLOE Table 10. Slave FIFO Asynchronous Read Parameters [20] Parameter Description Min Max Unit tRDpwl SLRD pulse width LOW 50 – ns tRDpwh SLRD pulse width HIGH 50 – ns tXFLG SLRD to FLAGS output propagation delay – 70 ns tXFD SLRD to FIFO data output propagation delay – 15 ns tOEon SLOE turn on to FIFO data valid – 10.5 ns tOEoff SLOE turn off to FIFO data hold – 10.5 ns Slave FIFO Asynchronous Write Figure 12. Slave FIFO Asynchronous Write Timing Diagram [19] tWRpwh SLWR/SLCS# tWRpwl tSFD tFDH DATA tXFD FLAGS Table 11. Slave FIFO Asynchronous Write Parameters with Internally Sourced IFCLK [21] Min Max Unit tWRpwl Parameter SLWR pulse LOW Description 50 – ns tWRpwh SLWR pulse HIGH 70 – ns tSFD SLWR to FIFO DATA setup time 10 – ns tFDH FIFO DATA to SLWR hold time 10 – ns tXFD SLWR to FLAGS output propagation delay – 70 ns Notes 19. Dashed lines denote signals with programmable polarity. 20. Slave FIFO asynchronous parameter values use internal IFCLK setting at 48 MHz. 21. GPIF asynchronous RDYx signals have a minimum setup time of 50 ns when using internal 48 MHz IFCLK. Document Number: 001-04247 Rev. *J Page 29 of 40 CY7C68033/CY7C68034 Slave FIFO Asynchronous Packet End Strobe Figure 13. Slave FIFO Asynchronous Packet End Strobe Timing Diagram [22] tPEpwh PKTEND tPEpwl FLAGS tXFLG Table 12. Slave FIFO Asynchronous Packet End Strobe Parameters [23] Parameter Description Min Max Unit tPEpwl PKTEND pulse width LOW 50 – ns tPWpwh PKTEND pulse width HIGH 50 – ns tXFLG PKTEND to FLAGS output propagation delay – 115 ns Slave FIFO Output Enable Figure 14. Slave FIFO Output Enable Timing Diagram [24] SLOE tOEon DATA tOEoff Table 13. Slave FIFO Output Enable Parameters Min Max Unit tOEon Parameter SLOE assert to FIFO DATA output Description – 10.5 ns tOEoff SLOE deassert to FIFO DATA hold – 10.5 ns Notes 22. SFRs not part of the standard 8051 architecture. 23. Slave FIFO asynchronous parameter values use internal IFCLK setting at 48 MHz. 24. Dashed lines denote signals with programmable polarity. Document Number: 001-04247 Rev. *J Page 30 of 40 CY7C68033/CY7C68034 Slave FIFO Address to Flags/Data Figure 15. Slave FIFO Address to Flags/Data Timing Diagram [25] FIFOADR [1.0] tXFLG FLAGS tXFD DATA N N+1 Table 14. Slave FIFO Address to Flags/Data Parameters Parameter Description Min Max Unit tXFLG FIFOADR[1:0] to FLAGS output propagation delay – 10.7 ns tXFD FIFOADR[1:0] to FIFODATA output propagation delay – 14.3 ns Min Max Unit Slave FIFO Asynchronous Address Figure 16. Slave FIFO Asynchronous Address Timing Diagram [25] SLCS/FIFOADR [1:0] tSFA tFAH SLRD/SLWR/PKTEND Table 15. Slave FIFO Asynchronous Address Parameters [26] Parameter Description tSFA FIFOADR[1:0] to SLRD/SLWR/PKTEND Setup Time 10 – ns tFAH RD/WR/PKTEND to FIFOADR[1:0] Hold Time 10 – ns Notes 25. Dashed lines denote signals with programmable polarity. 26. Slave FIFO asynchronous parameter values use internal IFCLK setting at 48 MHz. Document Number: 001-04247 Rev. *J Page 31 of 40 CY7C68033/CY7C68034 Sequence Diagram Sequence Diagram of a Single and Burst Asynchronous Read Figure 17. Slave FIFO Asynchronous Read Sequence and Timing Diagram [27] tSFA tFAH tSFA tFAH FIFOADR t=0 tRDpwl tRDpwh tRDpwl T=0 tRDpwl tRDpwh tRDpwl tRDpwh tRDpwh SLRD t=2 t=3 T=3 T=2 T=4 T=5 T=6 SLCS tXFLG tXFLG FLAGS tXFD Data (X) Driven DATA tXFD tXFD N N N+3 N+2 tOEon tOEoff tOEon tXFD N+1 tOEoff SLOE t=4 t=1 T=7 T=1 Figure 18. Slave FIFO Asynchronous Read Sequence of Events Diagram SLOE FIFO POINTER N FIFO DATA BUS Not Driven SLRD SLRD SLOE SLOE SLRD SLRD SLRD SLRD SLOE N N N+1 N+1 N+1 N+1 N+2 N+2 N+3 N+3 Driven: X N N Not Driven N N+1 N+1 N+2 N+2 Not Driven Figure 17 shows the timing relationship of the SLAVE FIFO signals during an asynchronous FIFO read. It shows a single read followed by a burst read. ■ The data that is driven, after asserting SLRD, is the updated data from the FIFO. This data is valid after a propagation delay of tXFD from the activating edge of SLRD. In Figure 17, data N is the first valid data read from the FIFO. For data to appear on the data bus during the read cycle (that is SLRD is asserted), SLOE MUST be in an asserted state. SLRD and SLOE can also be tied together. ■ At t = 0 the FIFO address is stable and the SLCS signal is asserted. ■ At t = 1, SLOE is asserted. This results in the data bus being driven. The data that is driven on to the bus is previous data, it data that was in the FIFO from a prior read cycle. The same sequence of events is also shown for a burst read marked with T = 0 through 5. At t = 2, SLRD is asserted. The SLRD must meet the minimum active pulse of tRDpwl and minimum deactive pulse width of tRDpwh. If SLCS is used then, SLCS must be in asserted with SLRD or before SLRD is asserted (that is the SLCS and SLRD signals must both be asserted to start a valid read condition). Note In burst read mode, during SLOE is assertion, the data bus is in a driven state and outputs the previous data. After SLRD is asserted, the data from the FIFO is driven on the data bus (SLOE must also be asserted) and then the FIFO pointer is incremented. ■ Note 27. Dashed lines denote signals with programmable polarity. Document Number: 001-04247 Rev. *J Page 32 of 40 CY7C68033/CY7C68034 Sequence Diagram of a Single and Burst Asynchronous Write Figure 19. Slave FIFO Asynchronous Write Sequence and Timing Diagram [28] tSFA tFAH tSFA tFAH FIFOADR t=0 tWRpwl tWRpwh T=0 tWRpwl tWRpwl tWRpwh tWRpwl tWRpwh tWRpwh SLWR t=3 t =1 T=1 T=3 T=4 T=6 T=7 T=9 SLCS tXFLG tXFLG FLAGS tSFD tFDH tSFD tFDH tSFD tFDH tSFD tFDH N+1 N+2 N+3 N DATA t=2 T=2 T=5 T=8 tPEpwl tPEpwh PKTEND Figure 19 shows the timing relationship of the SLAVE FIFO write in an asynchronous mode. The diagram shows a single write followed by a burst write of three bytes and committing the 4-byte-short packet using PKTEND. The FIFO flag is also updated after tXFLG from the deasserting edge of SLWR. ■ At t = 0 the FIFO address is applied, insuring that it meets the setup time of tSFA. If SLCS is used, it must also be asserted (SLCS may be tied low in some applications). ■ At t = 1 SLWR is asserted. SLWR must meet the minimum active pulse of tWRpwl and minimum de-active pulse width of tWRpwh. If the SLCS is used, it must be in asserted with SLWR or before SLWR is asserted. Note In the burst write mode, after SLWR is deasserted, the data is written to the FIFO and then the FIFO pointer is incremented to the next byte in the FIFO. The FIFO pointer is post incremented. ■ At t = 2, data must be present on the bus tSFD before the deasserting edge of SLWR. At t = 3, deasserting SLWR causes the data to be written from the data bus to the FIFO and then increments the FIFO pointer. The same sequence of events are shown for a burst write and is indicated by the timing marks of T = 0 through 5. As shown in Figure 19 after the four bytes are written to the FIFO and SLWR is deasserted, the short 4-byte packet can be committed to the host using the PKTEND. The external device should be designed to not assert SLWR and the PKTEND signal at the same time. It should be designed to assert the PKTEND after SLWR is deasserted and met the minimum de-asserted pulse width. The FIFOADDR lines are to be held constant during the PKTEND assertion. Note 28. Dashed lines denote signals with programmable polarity. Document Number: 001-04247 Rev. *J Page 33 of 40 CY7C68033/CY7C68034 Ordering Information Ordering Code Description Silicon for battery-powered applications CY7C68034-56LTXC 8 × 8 mm, 56-pin QFN (Sawn) CY7C68034-56LTXI 8 × 8 mm, 56-pin QFN (Sawn) Silicon for non-battery-powered applications CY7C68033-56LTXC 8 × 8 mm, 56-pin QFN (Sawn) Development Kit CY3686 EZ-USB NX2LP-Flex Development Kit Ordering Code Definitions CY 7 C 68 03X - 56 LT X X X X = T or blank T = Tape and Reel; blank = Tube Temperature Range: X = C or I C = Commercial; I = Industrial X = Pb-free (RoHS Compliant) Package Type: LT = QFN package No. of pins in package: 56-pin Part Number: 03X = 034 or 033 Family Code: 68 = USB Technology Code: C = CMOS Marketing Code: 7 = SRAM Company ID: CY = Cypress Document Number: 001-04247 Rev. *J Page 34 of 40 CY7C68033/CY7C68034 Package Diagrams Figure 20. 56-pin QFN (8 × 8 × 1.0 mm) LT56B 4.5 × 5.2 EPAD (Sawn), 001-53450 001-53450 *B Document Number: 001-04247 Rev. *J Page 35 of 40 CY7C68033/CY7C68034 PCB Layout Recommendations Follow these recommendations [29] to ensure reliable high performance operation: ■ At least a four-layer impedance controlled boards is recommended to maintain signal quality. ■ Specify impedance targets (ask your board vendor what they can achieve) to meet USB specifications. ■ To control impedance, maintain trace widths and trace spacing. ■ Minimize any stubs to avoid reflected signals. ■ Connections between the USB connector shell and signal ground must be done near the USB connector. ■ Bypass/flyback recommended. ■ DPLUS and DMINUS trace lengths should be kept to within 2 mm of each other in length, with preferred length of 20–30 mm. ■ Maintain a solid ground plane under the DPLUS and DMINUS traces. Do not allow the plane to be split under these traces. ■ No vias should be placed on the DPLUS or DMINUS trace routing unless absolutely necessary. ■ Isolate the DPLUS and DMINUS traces from all other signal traces as much as possible. caps on VBUS, near connector, are Quad Flat Package No Leads (QFN) Package Design Notes Electrical contact of the part to the printed circuit board (PCB) is made by soldering the leads on the bottom surface of the package to the PCB. Therefore, special attention is required to the heat transfer area below the package to provide a good thermal bond to the circuit board. Design a copper (Cu) fill into the PCB as a thermal pad under the package. Heat is transferred from the NX2LP-Flex to the PCB through the device’s metal paddle on the bottom side of the package. It is then conducted from the PCB’s thermal pad to the inner ground plane by a 5 × 5 array of vias. A via is a plated through hole in the PCB with a finished diameter of 13 mil. The QFN’s metal die paddle must be soldered to the PCB’s thermal pad. Solder mask is placed on the board top side over each via to resist solder flow into the via. The mask on the top side also minimizes outgassing during the solder reflow process. For further information on this package design, refer to the application note Application Note for Surface Mount Assembly of Amkor’s Eutectic and Lead-Free CSPnl™ Wafer Level Chip Scale Packages. This application note provides detailed information on board mounting guidelines, soldering flow, rework process, and so on. Note 29. Source for recommendations: EZ-USB FX2™PCB Design Recommendations and High Speed USB Platform Design Guidelines. Document Number: 001-04247 Rev. *J Page 36 of 40 CY7C68033/CY7C68034 Figure 21 displays a cross-sectional area underneath the package. The cross section is of only one via. The solder paste template needs to be designed to enable at least 50% solder coverage. The thickness of the solder paste template should be 5 mil. It is recommended that ‘No Clean’ type 3 solder paste is used for mounting the part. Nitrogen purge is recommended during reflow. Figure 22 is a plot of the solder mask pattern and Figure 23 displays an X-Ray image of the assembly (darker areas indicate solder). Figure 21. Cross-section of the Area Underneath the QFN Package. 0.017” dia Solder Mask Cu Fill Cu Fill PCB Material Via hole for thermally connecting the QFN to the circuit board ground plane. 0.013” dia PCB Material This figure only shows the top three layers of the circuit board: Top Solder, PCB Dielectric, and the Ground Plane. Figure 22. Plot of the Solder Mask (White Area) Figure 23. X-ray Image of the Assembly Document Number: 001-04247 Rev. *J Page 37 of 40 CY7C68033/CY7C68034 Acronyms Acronym Document Conventions Description Units of Measure ASIC application specific integrated circuit CPU central processing unit °C Symbol degree Celsius Unit of Measure DSP digital signal processor kHz kilohertz ECC error correcting codes MHz megahertz EEPROM electrically erasable programmable read only memory µA microampere µs microsecond FIFO first in first out GPIF general programmable interface µW microwatt GPIO general purpose input/output mA milliampere I/O input/output mm millimeter LAN local area network ms millisecond LSB least-significant bit mV millivolt MSB most-significant bit mW milliwatt PLL phase locked loop ns nanosecond PCB printed circuit board ohms PSoC programmable system-on-chip % percent QFN quad flat no leads pF picofarad RAM random access memory ROM read only memory SCL serial clock SDA serial data line SIE serial interface engine USB universal serial bus Document Number: 001-04247 Rev. *J ppm parts per million V volt Page 38 of 40 CY7C68033/CY7C68034 Document History Page Document Title: CY7C68033/CY7C68034, EZ-USB® NX2LP-Flex™ Flexible USB NAND Flash Controller Document Number: 001-04247 REV. ECN NO. Submission Date Orig. of Change Description of Change ** 388499 See ECN GIR Preliminary draft *A 394699 See ECN XUT Minor Change: Upload data sheet to external website. Publicly announcing the parts. No physical changes to document were made *B 400518 See ECN GIR Took ‘Preliminary’ off the top of all pages. Corrected the first bulleted item. Corrected Figure 3-2 caption. Added new logo *C 433952 See ECN RGL Added I2C functionality *D 498295 See ECN KKU Updated Data sheet format Changed In/Output reference from I/O to I/O Changed set-up to setup Changed IFCLK and CLKOUT pins to GPIO8 and GPIO9. Removed external IFCLK *E 2717536 06/11/2009 DPT Added 56 QFN (8 X 8 mm) package diagram and added CY7C68033-56LTXC and CY7C68034-56LTXC part information in the Ordering Information table *F 2728424 07/02/2009 GNKK *G 2896281 03/19/2010 ODC *H 2933818 05/18/2010 SHAH / AESA *I 3349690 08/25/2011 ODC Updated Package Diagrams (Removed Package Drawing 51-85144). Added Units of Measure. Updated in new template. *J 3668026 07/06/2012 GAYA Updated Ordering Information with part number CY7C68034-56LTXI. Document Number: 001-04247 Rev. *J Updated revision in the footer Removed inactive parts.Updated package diagram. Added table of contents.Updated links in Sales, Solutions and Legal Information. Added Contents and Acronyms Updated Default NAND Firmware Features Formatted table footnotes. Page 39 of 40 CY7C68033/CY7C68034 Sales, Solutions, and Legal Information Worldwide Sales and Design Support Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives, and distributors. To find the office closest to you, visit us at Cypress Locations. Products Automotive Clocks & Buffers Interface Lighting & Power Control PSoC Solutions cypress.com/go/automotive cypress.com/go/clocks psoc.cypress.com/solutions cypress.com/go/interface PSoC 1 | PSoC 3 | PSoC 5 cypress.com/go/powerpsoc cypress.com/go/plc Memory Optical & Image Sensing cypress.com/go/memory cypress.com/go/image PSoC Touch Sensing cypress.com/go/psoc cypress.com/go/touch USB Controllers Wireless/RF cypress.com/go/USB cypress.com/go/wireless © Cypress Semiconductor Corporation, 2005-2012. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be used for medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges. Any Source Code (software and/or firmware) is owned by Cypress Semiconductor Corporation (Cypress) and is protected by and subject to worldwide patent protection (United States and foreign), United States copyright laws and international treaty provisions. Cypress hereby grants to licensee a personal, non-exclusive, non-transferable license to copy, use, modify, create derivative works of, and compile the Cypress Source Code and derivative works for the sole purpose of creating custom software and or firmware in support of licensee product to be used only in conjunction with a Cypress integrated circuit as specified in the applicable agreement. Any reproduction, modification, translation, compilation, or representation of this Source Code except as specified above is prohibited without the express written permission of Cypress. Disclaimer: CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Cypress reserves the right to make changes without further notice to the materials described herein. Cypress does not assume any liability arising out of the application or use of any product or circuit described herein. Cypress does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress’ product in a life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges. Use may be limited by and subject to the applicable Cypress software license agreement. Document Number: 001-04247 Rev. *J Revised July 6, 2012 All products and company names mentioned in this document may be the trademarks of their respective holders. Page 40 of 40