Ecliptek EC3SM1B-20-30.000MTR Crystal Datasheet

Marketing Bulletin
DATE:
June 23rd, 2006
TO:
All Sales Personnel
FROM:
Mark Stoner
RE:
Product Termination
To all concerned parties,
This bulletin is to notify all customers of the discontinuation of the following Ecliptek
series effective July 1st, 2006:
Series
EC3SM1
EC4SM1
Description
Four pad SMD Crystal
Four pad SMD Crystal
Recommended Replacement
EC3SM
EC4SM
In compliance with our End of Life (EOL) policy, this will serve as advanced notice of
product termination. New orders will not be accepted after September 31st, 2006, with
delivery to conclude by December 31st 2006.
If there are any questions pertaining to this bulletin, please fell free to contact me.
Thank you again for your cooperation.
Best Regards,
Mark W. Stoner
Vice President of Marketing
Ecliptek Corporation
3545 CADILLAC AVENUE • COSTA MESA, CA 92626-1401 • (714) 433-1200 • Fax (714) 433-1234
EC3SM1 Series
EC3SM1
• Four pad surface mount package
• AT or BT cut available
• Resistance weld seal
• Tight tolerance/stability
• Interchangeable with plastic
surface mount crystals
• Tape and reel available
NOTES
H 5.18
L 12.50
W 4.95
CRYSTAL
__________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
OBSOLETE
__________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
__________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
__________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
__________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
__________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
_________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
__________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
ELECTRICAL SPECIFICATIONS
Frequency Range
4.000MHz, 7.3728MHz, 20.000MHz, and 30.000MHz
Frequency Tolerance / Stability
±50ppm / ±100ppm (Standard), ±30ppm / ±50ppm (AT cut only), ±15ppm / ±30ppm (AT cut only),
Over Operating Temperature Range
or ±15ppm / ±20ppm (AT cut only)
Operating Temperature Range
0°C to 70°C (Standard), -20°C to 70°C (AT cut only), or -40°C to 85°C (AT cut only)
Aging (at 25°C)
±5ppm / year Maximum
Storage Temperature Range
-40°C to 85°C
Shunt Capacitance
7pF Maximum
Insulation Resistance
500 Megaohms Minimum at 100VDC
Drive Level
1 mWatt Maximum
Load Capacitance (CL)
18pF (Standard), Custom CL ≥10pF, or Series Resonant
EQUIVALENT SERIES RESISTANCE (ESR), MODE OF OPERATION (MODE), AND CUT
Nominal Frequency
ESR (Ω)
Mode / Cut
Nominal Frequency
ESR (Ω)
Mode / Cut
4.000MHz
200 Max
Fundamental / AT
30.000MHz
40 Max
Fundamental / AT
7.3728MHz
120 Max
Fundamental / AT
30.000MHz
40 Max
Fundamental / BT
20.000MHz
50 Max
Fundamental / AT
MANUFACTURER
CATEGORY
SERIES
PACKAGE
CLASS
REV.DATE
ECLIPTEK CORP.
CRYSTAL
EC3SM1
EPOXY BASE
CR34
06/06
800-ECLIPTEK www.ecliptek.com for latest revision
Specifications subject to change without notice.
PART NUMBERING GUIDE
EC3SM1 - B - 20 - 30.000M TR
PACKAGING OPTIONS
Blank=Bulk, TR=Tape and Reel
FREQUENCY TOLERANCE / STABILITY
Blank=±50ppm at 25°C, ±100ppm from 0°C to 70°C
A=±50ppm at 25°C, ±100ppm from -20°C to 70°C
B=±50ppm at 25°C, ±100ppm from -40°C to 85°C
C=±30ppm at 25°C, ±50ppm from 0°C to 70°C
D=±30ppm at 25°C, ±50ppm from -20°C to 70°C
E=±30ppm at 25°C, ±50ppm from -40°C to 85°C
F=±15ppm at 25°C, ±30ppm from 0°C to 70°C
G=±15ppm at 25°C, ±30ppm from -20°C to 70°C
J=±15ppm at 25°C, ±20ppm from 0°C to 70°C
FREQUENCY
LOAD CAPACITANCE
Blank=18pF (Standard), S=Series
XX=XXpF (Custom)
MODE OF OPERATION / CRYSTAL CUT
Blank=Fundamental / AT
B=Fundamental / BT
OBSOLETE
MECHANICAL DIMENSIONS
SUGGESTED SOLDER PAD LAYOUT
ALL DIMENSIONS IN MILLIMETERS
ALL DIMENSIONS IN MILLIMETERS
Coplanarity: 0.152 Maximum
Tolerances = ±0.2
TAPE AND REEL DIMENSIONS
ALL DIMENSIONS IN MILLIMETERS
A
B
C
D
E
24±.3
11.5±.1
10.75±.1
4±.1
2±.1
TAPE
REEL
M
N
O
P
Q
1.5 MIN
50 MIN
20.2 MIN
13±.2
40 MIN
QTY/REEL
1,000
F
G
H
J
K
L
R
S
T
U
V
12±.1
5.4±.1
1.5 +.1
12.5±.1
.4±.05
5.35 ±0.2
2.5 MIN
10 MIN
30.4 MAX
360 MAX
24.4+2-0
*Compliant to EIA-481A
MARKING SPECIFICATIONS
ENVIRONMENTAL/MECHANICAL SPECIFICATIONS
PARAMETER
SPECIFICATION
Fine Leak Test
Gross Leak Test
Mechanical Shock
Vibration
Solderability
Temperature Cycling
Resistance to Soldering Heat
Resistance to Solvents
MIL-STD-883, Method 1014, Condition A
MIL-STD-883, Method 1014, Condition C
MIL-STD-202, Method 213, Condition C
MIL-STD-883, Method 2007, Condition A
MIL-STD-883, Method 2002
MIL-STD-883, Method 1010
MIL-STD-883, Method 210
MIL-STD-883, Method 215
Line 1: E XX.XXX
Frequency in MHz
(5 Digits Maximum + Decimal)
MANUFACTURER
CATEGORY
SERIES
PACKAGE
CLASS
REV.DATE
ECLIPTEK CORP.
CRYSTAL
EC3SM1
EPOXY BASE
CR34
06/06
800-ECLIPTEK www.ecliptek.com for latest revision
Specifications subject to change without notice.
Similar pages