FAN73402 LED Backlight Driving Boost Switch Features Description Single-Channel Boost LED Switch Internal Power MOSFET for PWM Dimming: RDS(ON)=1.0Ω at VGS=10V, BVDSS=200V The FAN73402 is a single-channel boost controller that integrates an N-channel power MOSFET for PWM dimming using Fairchild’s proprietary planar Doublediffused MOSFET (DMOS) technology. Current-Mode PWM Control Internal Programmable Slope Compensation Wide Supply Voltage Range: 10V to 35V LED Current Regulation: ±1% Programmable Switching Frequency Analog and PWM Dimming Wide Dimming Ratio: On Time=10µs to DC Cycle-by-Cycle Current Limiting Thermal Shutdown: 150°C Open-LED Protection (OLP) Over-Voltage Protection (OVP) Over-Current Protection (OCP) Error Flag Generation (for External Load Switch) Internal Soft-Start 16-Lead SOIC Package The IC operates as a constant-current source for driving high-current LEDs. It uses Current Mode control with programmable slope compensation to prevent subharmonic oscillation. The IC provides protections including: open-LED protection, over-voltage protection, and direct-short protection for high system reliability. The IC internally generates a FAULT signal with delay if an abnormal LED string condition occurs. PWM dimming and analog dimming functions can be implemented independently. Internal soft-start prevents inrush current flowing into output capacitor at startup. Applications LED Backlight for LCD TV LED Backlight for LCD Monitor LED Lighting Ordering Information Part Number Operating Temperature Range Package Packing Method FAN73402MX -40°C to +125°C 16-Lead, Small-Outline Integrated Circuit (SOIC) Tape & Reel © 2012 Fairchild Semiconductor Corporation FAN7340 • 1.0.0 www.fairchildsemi.com FAN73402 — LED Backlight Driving Boost Switch July 2012 20μs Delay - OVP OVP + 3V 100mV FAULT OLP TSD 1μs Delay + ADIM*4 1.4~4V S OCP - R POR Current Sense Q 640µs at 200kHz Auto-Restart PWM - 1/4 gm ADIM - R + + 0.3~3V Dim off DRV Q S Gate Driver PWM CMP 0.5V Slope Compensation 5k 100mV CS Burst Operation + CLK+LEB 4V + Switch Off 16 Steps Internal Soft-Start 3ms at 200kHz - 0.5V Oscillator GND RT 45µA Drain - UVLO 9V VCC PWM + 1.22V ENA Dim off OLPi Hys. 1.0V - BDIM + OLP Hys. 70mV Current Sense 5μs Delay 0.2V - 5V, max. 3mA 40.96ms at 200kHz Debounce Time + REF Voltage Reference & Internal Bias OLPi PWM SEN End of Soft-Start BDIM Figure 1. Internal Block Diagram © 2012 Fairchild Semiconductor Corporation FAN73402 • 1.0.0 www.fairchildsemi.com 2 FAN73402 — LED Backlight Driving Boost Switch Block Diagram FAN73402 — LED Backlight Driving Boost Switch Pin Assignments Figure 2. Package Diagram Pin Definitions Pin # Name Description 1 VCC This pin is the supply voltage of the IC. 2 DRV This pin is the gate drive signal of the boost switch. 3 GND This pin is the ground of the IC. This pin is for sensing the current flowing through an external MOSFET. It includes a built-in 300ns blanking time. The peak of the current flowing through the MOSFET is limited to this pin voltage. Slope compensation of the boost controller can be programmed through the series resistor of this pin. 4 CS 5 REF 6 FAULT 7 RT 8 SENSE This pin is for sensing the current flowing through the LEDs. A sensing resistor is connected from this pin to ground. This pin is connected to the negative input of the internal error amplifier. 9, 10 DRAIN Drain pin of PWM dimming power MOSFET. 12 ENA Enable input pin. If voltage of this pin is higher than 1.22V, the IC starts to operate. If the voltage of this pin is lower than 1.15V, the IC stops operating. 13 OVP Over-voltage protection input pin. Output voltage of the boost circuit is connected to this pin through a resistor divider circuit. If this pin voltage is higher than 3V, OVP is triggered. 14 CMP This pin is the error amplifier output. Typically, a compensation capacitor and resistor are connected to this pin from the ground. 15 ADIM This pin is for setting the current flowing through the LEDs. This pin is connected to the positive inputs of the internal error amplifier. Linear voltage range of ADIM is 0.3V~3.0V. 16 BDIM This pin is for the burst dimming signal. If this pin voltage is HIGH, the internal dimming MOSFET is turned on. If this pin voltage is LOW, the dimming MOSFET is turned off. This pin is the 5V reference voltage pin. Maximum current capability is 3mA. This pin is for indicating the fault signal. This pin is connected to the open drain. When OLP protection is occurred, the FAULT pin is pulled HIGH. Oscillator frequency set of the boost switch (50kHz ~ 300kHz). Note: 1. Pin 11 is a “No Connect” pin (not shown in Figure 2). © 2012 Fairchild Semiconductor Corporation FAN73402 • 1.0.0 www.fairchildsemi.com 3 Stresses exceeding the absolute maximum ratings may damage the device. The device may not function or be operable above the recommended operating conditions and stressing the parts to these levels is not recommended. In addition, extended exposure to stresses above the recommended operating conditions may affect device reliability. The absolute maximum ratings are stress ratings only. TA=25C unless otherwise specified. Symbol Parameter Min. Max. Unit V VCC Supply Voltage 10 35 TA Operating Temperature Range -40 +125 C TJ Junction Temperature +150 C +150 C 120 C/W 0.9 W TSTG Storage Temperature Range -65 ӨJA Thermal Resistance Junction-to-Ambient PD Power Dissipation (2,3) Notes: 2. Thermal resistance test board; size 76.2mm x 114.3mm x 1.6mm (1S0P); JEDEC standard: JESD51-2, JESD51-3. 3. Assume no ambient airflow. Pin Breakdown Voltage Pin # Name Value Unit Pin # Name Value Unit 1 VCC 35 V 9 DRAIN 200 V 2 DRV 20 V 10 DRAIN 200 V 3 GND 4 CS ENA 6 V V 6 V 12 5 REF 6 V 13 OVP 6 V 6 FAULT 35 V 14 CMP 6 V 7 RT 6 V 15 ADIM 6 V 8 SENSE 6 V 16 BDIM 6 V © 2012 Fairchild Semiconductor Corporation FAN73402 • 1.0.0 www.fairchildsemi.com 4 FAN73402 — LED Backlight Driving Boost Switch Absolute Maximum Ratings For typical values, TA = 25°C and VCC = 15V unless otherwise specified. Specifications to -40°C ~ 125°C are guaranteed by design based on final characterization results. Symbol Parameter Condition Min. Typ. Max. Unit 35 V 2 4 mA Supply Voltage Section VCC Input DC Supply Voltage Range(4) ISD Shutdown Mode Supply Current 10 BDIM Connected to GND Under-Voltage Lockout Section Vth Vth,hys Ist Start Threshold Voltage 8.3 9.0 9.7 V Start Threshold Voltage Hysteresis 0.5 1.0 1.5 V 200 300 μA 5 V 0.8 V 500 µmho Standby Current VCC=Vth-0.2 ON/OFF Section VON On-State Input Voltage VOFF Off-State Input Voltage 2 Error Amplifier Section Gm Error Amplifier Transconductance(4) VADIM=1V 100 (4) 300 AV_ro Error Amplifier Output impedance 20 MΩ AV Error Amplifier Open-Loop Gain(4) 60 dB Voffset Input Offset Voltage VADIM=1V -10 Isin CMP Sink Current VADIM=1V, VSENSE=2V 100 Isur CMP Source Current VADIM=1V, VSENSE=0V 100 VIDR VO Input Differential Voltage Range Output Voltage Range 10 mV 200 300 µA 200 300 µA 0 3 V 0.7 4.0 V 210 kHz Oscillator Section Minimum fosc Boost Oscillator Frequency RT=100kΩ 50 190 Maximum Dmax (4) Maximum Duty Cycle 200 300 86 90 94 % 4.9 5.0 5.1 V Reference Section VREF 5V Regulation Voltage VREF,Line 5V Line Regulation VREF,Load 5V Load Regulation 0<I5<3mA 25 mV 25 mV 0.8 V PWM Dimming Section VPDIM,L PWM Dimming Input Low Voltage VPDIM,H PWM Dimming Input High Voltage RPDIM 2 PWM Dimming Pull-Down Resistance 100 160 5 V 220 kΩ FET Section (for Dimming) BVDSS Drain-Source Breakdown Voltage(4) VCC=0V, ID=250μA IDSS Zero-Gate-Voltage Drain Current(4) VDS=250V, TA=25°C RDS(ON) Drain-Source On-State Resistance (4) 200 V 1 30 µA VGS=10V, ID=1A 0.7 1.0 Ω CISS Input Capacitance VDS=25V, VGS=0V, f=1MHz 173 225 pF COSS Output Capacitance(4) VDS=25V,VGS=0V, f=1MHz 30 40 pF Continued on the following page… © 2012 Fairchild Semiconductor Corporation FAN73402 • 1.0.0 www.fairchildsemi.com 5 FAN73402 — LED Backlight Driving Boost Switch Electrical Characteristics For typical values, TA = 25°C and VCC = 15V, unless otherwise specified. Specifications to -25°C ~ 85°C are guaranteed by design based on final characterization results. Symbol Parameter Condition Min. Typ. Max. Unit 10.8 11.8 12.8 V 0.5 V 180 280 mA 180 280 mA Output Section (Boost / Dimming) VDRV Gate Output Voltage VCC=15V Vuv Gate Output Voltage Before Startup Idsur (4) Idsin trh tfl -0.5 Gate Output Drive-Source Current 80 (4) Gate Output Drive-Sink Current 80 Gate Output Rising Time (Boost)(4) Gate Output Falling Time (Boost) (4) CL=2.0nF 200 ns CL=2.0nF 120 ns Current Sense Section tblank tdelay,cl Voffset,clc Leading-Edge Blanking(4) 150 300 Delay to Output of Current-Limit Comparator(4) Offset Voltage of Current-Limit Comparator(4) -20 450 ns 180 ns 20 mV 54 µA Slope Compensation Section Islope Rslope Ramp Generator Current Slope Compensation Resistor 36 (4) 45 5 kΩ 3 ms Soft-Start Section tss Soft-Start Period(4) fosc=200kHz Protection Section td,ovp.tr Delay for Triggering Over-Voltage Protection(4) 15 20 25 µs td,ovpr Delay for Releasing Over-Voltage Protection(4) 10 14 18 µs td.ocp tAR Delay for Over-Current Protection (4) Auto-Restart Time for Over-Current Protection(4) td,olpi Delay for Triggering Open-LED Protection(4) td,olp Delay for Open-LED Protection Vth,ovp Over-Voltage Protection Threshold Voltage Vhys,ovp Over-Voltage Protection Voltage Hysteresis Vth.csocp Boost Switch Current-Limit Threshold Voltage fosc=200kHz 3 fosc=200kHz 1 µs 640 µs 5 7 40.96 2.85 3.00 ms 3.15 0.1 0.45 0.50 µs V V 0.55 4.0 1.4 4.0xVA (Max. (Min. DIM Clamp) Clamp) V Vth,ocp LED Over-Current Protection Threshold Voltage Vth,olp Open-LED Protection Threshold Voltage(4) 0.15 0.20 0.25 V TSD Thermal Shutdown Temperature(4) 140 150 160 °C THYS Thermal Shutdown Hysteresis(4) 20 V °C Note: 4. These parameters, although guaranteed, are not tested in production. © 2012 Fairchild Semiconductor Corporation FAN73402 • 1.0.0 www.fairchildsemi.com 6 FAN73402 — LED Backlight Driving Boost Switch Electrical Characteristics (Continued) 9.9 1.7 9.7 1.5 9.5 1.3 Vth.hys, [V] Vth, [V] 9.3 9.1 8.9 8.7 1.1 0.9 0.7 8.5 0.5 8.3 0.3 8.1 -50 -25 0 25 50 75 Temperature, [℃] 100 -50 125 Figure 3. Start Threshold Voltage vs. Temperature -25 0 25 50 75 Temperature, [℃] 100 125 Figure 4. Start Threshold Voltage Hysteresis vs. Temperature 350 4.5 4 300 3.5 ISD, [mA] Ist, [µA] 250 200 150 3 2.5 2 1.5 100 1 50 0.5 -50 -25 0 25 50 75 Temperature, [℃] 100 -50 125 Figure 5. Standby Current vs. Temperature 0 25 50 75 Temperature, [℃] 100 125 Figure 6. Shutdown Mode Supply Current vs. Temperature 1.4 1.3 1.35 1.25 1.3 1.2 VOFF, [V] VON, [V] -25 1.25 1.2 1.15 1.15 1.1 1.1 1.05 1.05 1 -50 -25 0 25 50 75 Temperature, [℃] 100 -50 125 Figure 7. On-State Input Voltage vs. Temperature © 2012 Fairchild Semiconductor Corporation FAN73402 • 1.0.0 -25 0 25 50 75 Temperature, [℃] 100 125 Figure 8. Off-State Input Voltage vs. Temperature www.fairchildsemi.com 7 FAN73402 — LED Backlight Driving Boost Switch Typical Performance Characteristics 14 500 10 6 400 Voffset, [mV] Gm, [umho] 600 300 200 100 -6 -14 -50 -25 0 25 50 75 Temperature, [℃] 100 125 -50 Figure 9. Error Amplifier Transconductance vs. Temperature 350 350 300 300 250 250 200 150 100 100 50 50 -25 0 25 50 75 Temperature, [℃] 100 -50 125 Figure 11. CMP Sink Current vs. Temperature 210 94 205 92 Dmax, [%] 96 200 195 185 84 25 50 75 Temperature, [℃] 100 125 -50 Figure 13. Boost Oscillator Frequency vs. Temperature © 2012 Fairchild Semiconductor Corporation FAN73402 • 1.0.0 125 -25 0 25 50 75 Temperature, [℃] 100 125 88 86 0 100 90 190 -25 25 50 75 Temperature, [℃] Figure 12. CMP Source Current vs. Temperature 215 -50 0 200 150 -50 -25 Figure 10. Input Offset Voltage vs. Temperature Isur, [µA] Isin, [µA] -2 -10 0 fOSC, [KHz] 2 -25 0 25 50 75 Temperature, [℃] 100 125 Figure 14. Maximum Duty Cycle vs. Temperature www.fairchildsemi.com 8 FAN73402 — LED Backlight Driving Boost Switch Typical Performance Characteristics (Continued) 1.8 5.1 1.7 5.05 1.6 VPDIM,H, [V] VREF, [V] 5.15 5 4.95 1.5 1.4 4.9 1.3 4.85 1.2 -50 Figure 15. -25 0 25 50 75 Temperature, [℃] 100 -50 125 -25 0 25 50 75 100 125 Temperature, [℃] 5V Regulation Voltage vs. Temperature Figure 16. PWM Dimming Input High Voltage vs. Temperature 1.7 240 220 1.6 RPDIM, [Kohm] VPDIM,L, [V] 200 1.5 1.4 1.3 180 160 140 120 1.2 100 80 1.1 -50 -25 0 25 50 75 Temperature, [℃] 100 -50 125 Figure 17. PWM Dimming Input Low Voltage vs. Temperature 0 25 50 75 Temperature, [℃] 100 125 Figure 18. PWM Dimming Pull-Down Resistance vs. Temperature 300 13.5 13 250 Idsin, [mA] 12.5 VDRV, [V] -25 12 11.5 200 150 100 11 10.5 50 -50 -25 0 25 50 75 Temperature, [℃] 100 125 -50 Figure 19. Gate Output Voltage vs. Temperature © 2012 Fairchild Semiconductor Corporation FAN73402 • 1.0.0 -25 0 25 50 75 Temperature, [℃] 100 125 Figure 20. Gate Output Drive Sink Current vs. Temperature www.fairchildsemi.com 9 FAN73402 — LED Backlight Driving Boost Switch Typical Performance Characteristics (Continued) 0.85 55 0.8 0.75 47 tAR,[mS] Islope, [µA] 51 43 0.7 0.65 0.6 0.55 39 0.5 0.45 35 -50 -25 0 25 50 75 Temperature, [℃] 100 -50 125 -25 0 25 50 75 100 125 Temperature, [℃] Figure 21. Ramp Generator Current vs. Temperature Figure 22. Auto-Restart Time for OC vs. Temperature 3.2 0.2 3.15 0.16 Vhys,ovp,[V] Vth,ovp,[V] 3.1 3.05 3 2.95 0.12 0.08 2.9 0.04 2.85 2.8 0 -50 -25 0 25 50 75 Temperature, [℃] 100 125 -50 Figure 23. OVP Threshold Voltage vs. Temperature -25 0 25 50 75 Temperature, [℃] 100 125 Figure 24. OVP Hysteresis Voltage vs. Temperature 55 td,olp,[mS] 50 45 40 35 30 25 -50 Figure 25. © 2012 Fairchild Semiconductor Corporation FAN73402 • 1.0.0 -25 0 25 50 75 Temperature, [℃] 100 125 Delay for Over-Current Protection vs. Temperature www.fairchildsemi.com 10 FAN73402 — LED Backlight Driving Boost Switch Typical Performance Characteristics (Continued) The FAN73402 operates as a constant-current source for driving high-current LEDs. It uses Current-Mode control with programmable slope compensation to prevent subharmonic oscillation. The IC provides open-LED protection, over-voltage protection, and over-current protection for improved system reliability. The IC internally generates a FAULT OUT signal with a delay in case an abnormal LED string condition occurs. PWM dimming and analog dimming functions can be implemented independently. Internal soft-start prevents inrush current flowing into output capacitor at startup. Figure 26. VCC Under-Voltage Lockout (UVLO) Soft-Start Waveforms LED Current Setting An internal regulator provides the regulated 5V used to power the IC. The Under-Voltage Lockout (UVLO) turns off the IC in the event of the voltage dropping below the specific threshold level. The UVLO circuit inhibits powering the IC until a voltage reference is established, up to predetermined threshold level. During the boost converter operating periods, the output LED current can be set by equation: I Enable R ADIM V 60mΩ (3) where ADIM(V) is ADIM pin applied voltage and, RSENSE is the sensing resistor value. Applying voltage higher than 1.22V (typical) to the ENA pin enables the IC. Applying voltage lower than 1.15V (typical) to the ENA pin disables the IC. If ENA pin voltage is higher than 1.22V (typical) and VCC is higher than 9.0V (typical), the IC starts to supply the 5V reference voltage from VCC. Note: 5. An additional 60mΩ comes from an internal wire bonding resistor. To calculate LED current precisely, consider the wire bonding resistor. Oscillator (Boost Switching Frequency) Analog Dimming and PWM Dimming Boost switching frequency is programmed by the value of the resistor connected from the RT pin to ground. RT pin voltage is set to 2V. The current through the RT pin resistor determines the boost switching frequency according to formula: Analog dimming (ADIM) is achieved by varying the voltage level at the ADIM pin. This can be implemented either with a potentiometer from the VREF pin or from an external voltage source and a resistor divider circuit. The ADIM voltage level is adjusted to be the same as the feedback level (VSENSE). A VADIM range from 0.3V to 3V is recommended. f kHz . (1) PWM dimming (BDIM) helps achieve a fast PWM dimming response in spite of the shortcomings of the boost converter. The PWM dimming signal controls three nodes in the IC: gate signal to the switching FET, gate signal to the dimming FET, and output connection of the transconductance amplifier. When the PWM dimming signal is HIGH, the gates of the switching FET and dimming FET are enabled. At the same time, the output of the transconductance op-amp is connected to the compensation network. This allows the boost converter to operate normally. Soft-Start Function at Startup During initial startup, the switching device can be damaged due to the over-current coming from the input line by the negative control. This can result in the initial overshoot of the LED current. Therefore, during initial startup, the soft-start control gradually increases the duty cycle so that the output voltage can rise smoothly to control inrush current and overshoot. FAN73402 adapts the soft-start function in the boost converter stage. During soft-start period, boost switch turn-on duty is limited by the clamped CMP voltage. The soft-start period is dependent on the boost switching frequency, which is determined by the RT resistor (Equation 1). Soft-start period is set to be cumulative time when the BDIM (PWM dimming) signal is HIGH: t 600 / f seconds © 2012 Fairchild Semiconductor Corporation FAN73402 • 1.0.0 Dynamic Contrast Ratio The Dynamic Contrast Ratio (DCR) means the maximum contrast ratio achievable by adjusting the amount of light (dimming) of the screen using the backlight during an extremely short period of time. FAN73402 can normally drive the LED backlight under 0.1% dimming duty cycle at 200Hz dimming frequency. Even operating at 5µs dimming MOSFET turn-on time and extremely low dimming duty, FAN73402 can operate LEDs with normal peak current level. (2) www.fairchildsemi.com 11 FAN73402 — LED Backlight Driving Boost Switch Functional Description A dimming MOSFET (200V N-channel MOSFET) is incorporated in the FAN73402. The power transistor is produced using Fairchild’s proprietary, planar stripe, DMOS technology. This advanced technology is tailored to minimize on-state resistance (RDS(on)=1.0) to provide superior switching performance. This device is suited for high-efficiency SMPS and shows desirable thermal characteristic during operation. To prevent initial LED current overshoot at low VADIM levels, gate resistance of the internal dimming FET is designed as 5k. Figure 27. Feedback Loop Compensation Slope Compensation Cycle-by-Cycle Over-Current Protection Stable closed-loop control can be accomplished by connecting a compensation network between COMP and GND. The compensation needed to stabilize the converter can be a Type-I circuit (a simple integrator) or a Type-II circuit (and integrator with and additional polezero pair). The type of the compensation circuit required is dependent on the phase of the power stage at the crossover frequency. In boost topology, the switch can be damaged in abnormal conditions (inductor short, diode short, output short). It is always necessary to sense the switch current to protect against over-current failures. Switch failures due to excessive current can be prevented by limiting Id. FAN73402 adopts a Type-II compensator circuit. Programmed Current Control FAN73402 uses Current-Mode control. Current-Mode control loops: an outer feedback loop that senses output voltage (current) and delivers a DC control voltage to an inner feedback loop, which senses the peak current of the inductor and keeps it constant on a pulse-by-pulse basis. One of the advantages of the Current-Mode control is line/load regulation, which is corrected instantaneously against line voltage changes without the delay of an error amplifier. Figure 28. Cycle-by-Cycle OCP Circuit When the voltage drops at R1 and RS exceed a threshold of approximately 0.5V, the power MOSFET over-current function is triggered after minimum turn-on time or LEB time (300ns). Programmable Slope Compensation When the power converter operates in Continuous Conduction Mode (CCM), the current programmed controller is inherently unstable when duty is larger than 50%, regardless of the converter topology. The FAN73402 uses a Peak-Current-Mode control scheme with programmable slope compensation and includes an internal transconductance amplifier to accurately control the output current over all line and load conditions. The peak voltage level at CS terminal: V 45μ _ R R DT I R (4) Choose the boost switch current-sensing resistor (RCS): R An internal Rslope resistor (5kΩ) connected to sensing resistor, RS, and an external resistor, R1, can control the slope of VSC for the slope compensation. Although the normal operating mode of the power converter is DCM, the boost converter operates in CCM in the case of rapid LED current increase. As a result, slope compensation is an important feature. 0.25 I _ (5) Open-LED Protection (OLP) After the first PWM dimming-HIGH signal, the feedback sensing resistor (RSENSE) starts sensing the LED current. If the feedback voltage of the SENSE pin drops below 0.2V, the OLP triggers to generate an error flag signal. Because OLP can be detected only in PWM dimmingHIGH; if OLP detecting time is over 5μs, PWM dimming signal is pulled HIGH internally regardless of external dimming signal. If OLP signal continues over blanking time, an error flag signal is triggered. The value of an external series resistor (R1) can be programmed. In normal DCM operation, 5k is recommended. OLP blanking time is dependent on the boost switch frequency, per Equation 6. FAULT OUT signal is made through the FAULT pin, which needs to be connected 5V reference voltage through a pull-up resistor. In normal operation, the FAULT pin voltage is pulled down to ground. In OLP condition, the FAULT pin voltage is pulled HIGH. © 2012 Fairchild Semiconductor Corporation FAN73402 • 1.0.0 www.fairchildsemi.com 12 FAN73402 — LED Backlight Driving Boost Switch Internal Dimming MOSFET . 8192 / f seconds (6) LED Over-Current Protection (OCP) In system operation, OLP is triggered in only direct-short condition. Direct short means that some point of the LED string is shorted to set ground. In direct-short condition, the boost controller cannot control the LED current and a large current flows into the LED string directly from input power. To prevent this abnormal condition, the FAULT signal is used to turn off input power or the total system. FAULT signal is only triggered in OLP condition. The primary purpose of the over-current protection function is to protect the internal dimming MOSFET from excessive current. The OCP is triggered when the feedback voltage meets the clamping level (1.4V ~ 4V) of the ADIM voltage x4. At 1μs delay after the OCP is triggered, the IC turns off both the boost FET and dimming FET and restarts the gate signal every tAR automatically. tAR can be calculated as: t 128 / f seconds (7) When VADIM=0.3V (VADIMx4=1.2V). OCP threshold level is set to 1.4V. OCP is triggered at feedback voltage level = 1.4V. VSENSE VSENSE=1.4V VADIM=0.3V Figure 29. Open-LED Protection Note: 6. In LED-open load condition, OVP is triggered ahead of OLP. GATE Over-Voltage Protection (OVP) Figure 32. OCP Waveforms at VADIM=0.3V Over-voltage protection is triggered when the voltage of the external output voltage reaches 3V. After triggering OVP, the dimming switch and boost switch are turned off. The protection signal is recovered when the output voltage divider is below 2.9V. When VADIM=0.8V (VADIMx4=3.2V). OCP threshold level is set to 3.2V. OCP is triggered at VSENSE = 3.2V. Figure 33. OCP Waveforms at VADIM=0.8V When VADIM=1.2V (VADIMx4=4.8V). Figure 30. Over-Voltage Trip Point OCP threshold level is set to 4.0V. OCP is triggered at VSENSE = 4.0V. Figure 31. OVP Trigger and Release Figure 34. © 2012 Fairchild Semiconductor Corporation FAN73402 • 1.0.0 OCP Waveforms at VADIM=1.2V www.fairchildsemi.com 13 FAN73402 — LED Backlight Driving Boost Switch t Application Input Voltage Range LED Backlight TV 90VDC 10% Rated Output Power Output Current (Rated Voltage) LED 250mA (160V) 48-LEDs/1-String Features High Efficiency Constant Current Boost Converters High-Voltage, High-Current LED Driving Typical Application Circuit D1 CN1 Vin Vin Vin GND GND GND CN2 L1 200uH/PC44 1 2 3 4 5 6 C1 22uF/160V FFD04H60S C2 R1 10R 47uF/400V CON6 Q1 FDD7N50NF 0 R21 300k D2 1SS355 R9 0R R4 100K R23 10k D3 1SS355 On/Of f VCC GND FO BDIM ADIM On/Of f 1 2 3 4 5 6 5.1K 1 2 R8 0.2R/1W C14 1.2n R7 3 C3 10uF/50V 0 C4 1u 4 C5 OPEN REF CON6 C8 TP1 R19 10k 10n R12 100K/open FO 5 DRV GND 6 CS REF FAULT ADIM On/Of f R13 3.9K R15 220K TP R14 20K/open 7 C10 1.2n R20 100k BDIM R16 2.7R/1W R17 3.9K R18 220K 8 BDIM VCC VCC FO CON6 R5 270k VCC ENA R2 270k N.C N.C VLED VLED LED1 LED2 0 RT FAN73402 R22 300k CN3 1 2 3 4 5 6 SENSE 16 R6 300k BDIM OVP ADIM CMP OVP ENA 15 ADIM C13 1.2n R10 16k 14 13 OVP C6 6.8n 12 R11 15k C7 100n ENA DRAIN DRAIN 10 9 IC1 FAN734002 C11 1.2n Vin : 90V Vout : 160V Output current : 250mA Switching frequency : 200kHz 0 Figure 35. © 2012 Fairchild Semiconductor Corporation FAN73402 • 1.0.0 Typical Application Circuit www.fairchildsemi.com 14 FAN73402 — LED Backlight Driving Boost Switch Typical Application Circuit (Boost Topology for LED Backlight) 10.00 9.80 A 8.89 16 9 B 4.00 3.80 6.00 PIN ONE INDICATOR 1.75 1 5.6 8 0.51 0.35 1.27 (0.30) 0.25 M 1.27 C B A 0.65 LAND PATTERN RECOMMENDATION 1.75 MAX 1.50 1.25 SEE DETAIL A 0.25 0.10 C 0.25 0.19 0.10 C 0.50 0.25 X 45° (R0.10) NOTES: UNLESS OTHERWISE SPECIFIED GAGE PLANE (R0.10) 0.36 8° 0° A) THIS PACKAGE CONFORMS TO JEDEC MS-012, VARIATION AC, ISSUE C. B) ALL DIMENSIONS ARE IN MILLIMETERS. C) DIMENSIONS ARE EXCLUSIVE OF BURRS, MOLD FLASH AND TIE BAR PROTRUSIONS D) CONFORMS TO ASME Y14.5M-1994 E) LANDPATTERN STANDARD: SOIC127P600X175-16AM F) DRAWING FILE NAME: M16AREV12. SEATING PLANE 0.90 0.50 (1.04) DETAIL A SCALE: 2:1 Figure 36. 16-Lead, Small Outline Integrated Circuit (SOIC) Package drawings are provided as a service to customers considering Fairchild components. Drawings may change in any manner without notice. Please note the revision and/or date on the drawing and contact a Fairchild Semiconductor representative to verify or obtain the most recent revision. Package specifications do not expand the terms of Fairchild’s worldwide terms and conditions, specifically the warranty therein, which covers Fairchild products. Always visit Fairchild Semiconductor’s online packaging area for the most recent package drawings: http://www.fairchildsemi.com/packaging/. © 2012 Fairchild Semiconductor Corporation FAN73402 • 1.0.0 www.fairchildsemi.com 15 FAN73402 — LED Backlight Driving Boost Switch Physical Dimension FAN73402 — LED Backlight Driving Boost Switch © 2012 Fairchild Semiconductor Corporation FAN73402 • 1.0.0 www.fairchildsemi.com 16