ATMEL AT49BV642D 64-megabit (4m x 16) 3-volt only flash memory Datasheet

Features
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Single Voltage Operation Read/Write: 2.65V - 3.6V
2.7V - 3.6V Read/Write
Access Time – 70 ns
Sector Erase Architecture
– One Hundred Twenty-seven 32K Word Main Sectors with Individual Write Lockout
– Eight 4K Word Sectors with Individual Write Lockout
Fast Word Program Time – 10 µs
Typical Sector Erase Time: 32K Word Sectors – 500 ms; 4K Word Sectors – 100 ms
Suspend/Resume Feature for Erase and Program
– Supports Reading and Programming Data from Any Sector by Suspending Erase
of a Different Sector
– Supports Reading Any Word by Suspending Programming of Any Other Word
Low-power Operation
– 10 mA Active
– 15 µA Standby
Data Polling and Toggle Bit for End of Program Detection
VPP Pin for Write Protection and Accelerated Program Operations
RESET Input for Device Initialization
Sector Lockdown Support
TSOP Package
Top or Bottom Boot Block Configuration Available
128-bit Protection Register
Common Flash Interface (CFI)
Green (Pb/Halide-free) Packaging
64-megabit
(4M x 16)
3-volt Only
Flash Memory
AT49BV642D
AT49BV642DT
1. Description
The AT49BV642D(T) is a 2.7-volt 64-megabit Flash memory organized as 4,194,304
words of 16 bits each. The memory is divided into 135 sectors for erase operations.
The device can be read or reprogrammed off a single 2.7V power supply, making it
ideally suited for in-system programming.
To increase the flexibility of the device, it contains an Erase Suspend and Program
Suspend feature. This feature will put the erase or program on hold for any amount of
time and let the user read data from or program data to any of the remaining sectors.
The end of program or erase is detected by Data Polling or toggle bit.
The VPP pin provides data protection and faster programming times. When the VPP
input is below 0.4V, the program and erase functions are inhibited. When VPP is at
1.65V or above, normal program and erase operations can be performed. With VPP at
10.0V, the program (dual-word program command) operation is accelerated.
A six-word command (Enter Single Pulse Program Mode) to remove the requirement
of entering the three-word program sequence is offered to further improve programming time. After entering the six-word code, only single pulses on the write control
lines are required for writing into the device. This mode (Single Pulse Word Program)
is exited by powering down the device, by taking the RESET pin to GND or by a highto-low transition on the V PP input. Erase, Erase Suspend/Resume, Program Suspend/Resume and Read Reset commands will not work while in this mode; if entered
they will result in data being programmed into the device. It is not recommended that
the six-word code reside in the software of the final product but only exist in external
programming code.
3631A–FLASH–04/06
2. Pin Configurations
2.1
Pin Name
Pin Function
I/O0 - I/O15
Data Inputs/Outputs
A0 - A21
Addresses
CE
Chip Enable
OE
Output Enable
WE
Write Enable
RESET
Reset
VPP
Write Protection and Power Supply for Accelerated Program
Operations
VCCQ
Output Power Supply
TSOP Top View (Type 1)
A15
A14
A13
A12
A11
A10
A9
A8
A21
A20
WE
RESET
VPP
NC
A19
A18
A17
A7
A6
A5
A4
A3
A2
A1
2
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
A16
VCCQ
GND
I/O15
I/O7
I/O14
I/O6
I/O13
I/O5
I/O12
I/O4
VCC
I/O11
I/O3
I/O10
I/O2
I/O9
I/O1
I/O8
I/O0
OE
GND
CE
A0
AT49BV642D(T)
3631A–FLASH–04/06
AT49BV642D(T)
3. Device Operation
3.1
Command Sequences
The device powers on in the read mode. Command sequences are used to place the device in
other operating modes such as program and erase. After the completion of a program or an
erase cycle, the device enters the read mode. The command sequences are written by applying
a low pulse on the WE input with CE low and OE high or by applying a low-going pulse on the
CE input with WE low and OE high. The address is latched on the falling edge of the WE or CE
pulse whichever occurs first. Valid data is latched on the rising edge of the WE or the CE pulse,
whichever occurs first. The addresses used in the command sequences are not affected by
entering the command sequences.
3.2
Read
The AT49BV642D(T) is accessed like an EPROM. When CE and OE are low and WE is high,
the data stored at the memory location determined by the address pins are asserted on the outputs. The outputs are put in the high impedance state whenever CE or OE is high. This dual-line
control gives designers flexibility in preventing bus contention.
3.3
Reset
A RESET input pin is provided to ease some system applications. When RESET is at a logic
high level, the device is in its standard operating mode. A low level on the RESET pin halts the
present device operation and puts the outputs of the device in a high-impedance state. When a
high level is reasserted on the RESET pin, the device returns to read or standby mode, depending upon the state of the control pins.
3.4
Erase
Before a word can be reprogrammed it must be erased. The erased state of the memory bits is a
logical “1”. The entire memory can be erased by using the Chip Erase command or individual
sectors can be erased by using the Sector Erase command.
3.4.1
Chip Erase
Chip Erase is a six-bus cycle operation. The automatic erase begins on the rising edge of the
last WE pulse. Chip Erase does not alter the data of the protected sectors. After the full chip
erase the device will return back to the read mode. The hardware reset during Chip Erase will
stop the erase but the data will be of unknown state. Any command during Chip Erase except
Erase Suspend will be ignored.
3.4.2
Sector Erase
As an alternative to a full chip erase, the device is organized into multiple sectors that can be
individually erased. The Sector Erase command is a six-bus cycle operation. The sector whose
address is valid at the sixth falling edge of WE will be erased provided the given sector has not
been protected.
3
3631A–FLASH–04/06
3.5
Word Programming
The device is programmed on a word-by-word basis. Programming is accomplished via the
internal device command register and is a four-bus cycle operation. The programming address
and data are latched in the fourth cycle. The device will automatically generate the required
internal programming pulses. Please note that a “0” cannot be programmed back to a “1”; only
erase operations can convert “0”s to “1”s.
3.6
Sector Lockdown
Each sector has a programming lockdown feature. This feature prevents programming of data in
the designated sectors once the feature has been enabled. These sectors can contain secure
code that is used to bring up the system. Enabling the lockdown feature will allow the boot code
to stay in the device while data in the rest of the device is updated. This feature does not have to
be activated; any sector’s usage as a write-protected region is optional to the user.
At power-up or reset, all sectors are unlocked. To activate the lockdown for a specific sector, the
six-bus cycle Sector Lockdown command must be issued. Once a sector has been locked down,
the contents of the sector is read-only and cannot be erased or programmed.
3.6.1
Sector Lockdown Detection
A software method is available to determine if programming of a sector is locked down. When
the device is in the software product identification mode (see “Software Product Identification
Entry/Exit” sections on page 23), a read from address location 00002H within a sector will show
if programming the sector is locked down. If the data on I/O0 is low, the sector can be programmed; if the data on I/O0 is high, the program lockdown feature has been enabled and the
sector cannot be programmed. The software product identification exit code should be used to
return to standard operation.
3.6.2
Sector Lockdown Override
The only way to unlock a sector that is locked down is through reset or power-up cycles. After
power-up or reset, the content of a sector that is locked down can be erased and reprogrammed.
3.7
Program/Erase Status
The device provides several bits to determine the status of a program or erase operation: I/O2,
I/O3, I/O5, I/O6, and I/O7. All other status bits are don’t care. The “Status Bit Table” on page 10
and the following four sections describe the function of these bits. To provide greater flexibility
for system designers, the AT49BV642D(T) contains a programmable configuration register. The
configuration register allows the user to specify the status bit operation. The configuration register can be set to one of two different values, “00” or “01”. If the configuration register is set to
“00”, the part will automatically return to the read mode after a successful program or erase
operation. If the configuration register is set to a “01”, a Product ID Exit command must be given
after a successful program or erase operation before the part will return to the read mode. It is
important to note that whether the configuration register is set to a “00” or to a “01”, any unsuccessful program or erase operation requires using the Product ID Exit command to return the
device to read mode. The default value (after power-up) for the configuration register is “00”.
Using the four-bus cycle set configuration register command as shown in the “Command Definition Table” on page 11, the value of the configuration register can be changed. Voltages applied
to the reset pin will not alter the value of the configuration register. The value of the configuration
register will affect the operation of the I/O7 status bit as described below.
4
AT49BV642D(T)
3631A–FLASH–04/06
AT49BV642D(T)
3.7.1
Data Polling
The AT49BV642D(T) features Data Polling to indicate the end of a program cycle. If the status
configuration register is set to a “00”, during a program cycle an attempted read of the last word
loaded will result in the complement of the loaded data on I/O7. Once the program cycle has
been completed, true data is valid on all outputs and the next cycle may begin. During a chip or
sector erase operation, an attempt to read the device will give a “0” on I/O7. Once the program
or erase cycle has completed, true data will be read from the device. Data Polling may begin at
any time during the program cycle. Please see “Status Bit Table” on page 10 for more details.
If the status bit configuration register is set to a “01”, the I/O7 status bit will be low while the
device is actively programming or erasing data. I/O7 will go high when the device has completed
a program or erase operation. Once I/O7 has gone high, status information on the other pins can
be checked.
The Data Polling status bit must be used in conjunction with the erase/program and VPP status
bit as shown in the algorithm in Figures 3-1 and 3-2 on page 8.
3.7.2
Toggle Bit
In addition to Data Polling, the AT49BV642D(T) provides another method for determining the
end of a program or erase cycle. During a program or erase operation, successive attempts to
read data from the memory will result in I/O6 toggling between one and zero. Once the program
cycle has completed, I/O6 will stop toggling and valid data will be read. Examining the toggle bit
may begin at any time during a program cycle. Please see “Status Bit Table” on page 10 for
more details.
The toggle bit status bit should be used in conjunction with the erase/program and VPP status bit
as shown in the algorithm in Figures 3-3 and 3-4 on page 9.
3.7.3
Erase/Program Status Bit
The device offers a status bit on I/O5 that indicates whether the program or erase operation has
exceeded a specified internal pulse count limit. If the status bit is a “1”, the device is unable to
verify that an erase or a word program operation has been successfully performed. The device
may also output a “1” on I/O5 if the system tries to program a “1” to a location that was previously programmed to a “0”. Only an erase operation can change a “0” back to a “1”. If a program
(Sector Erase) command is issued to a protected sector, the protected sector will not be programmed (erased). The device will go to a status read mode and the I/O5 status bit will be set
high, indicating the program (erase) operation did not complete as requested. Once the
erase/program status bit has been set to a “1”, the system must write the Product ID Exit command to return to the read mode. The erase/program status bit is a “0” while the erase or
program operation is still in progress. Please see “Status Bit Table” on page 10 for more details.
3.7.4
VPP Status Bit
The AT49BV642D(T) provides a status bit on I/O3 that provides information regarding the voltage level of the VPP pin. During a program or erase operation, if the voltage on the VPP pin is
not high enough to perform the desired operation successfully, the I/O3 status bit will be a “1”.
Once the VPP status bit has been set to a “1”, the system must write the Product ID Exit command to return to the read mode. On the other hand, if the voltage level is high enough to
perform a program or erase operation successfully, the VPP status bit will output a “0”. Please
see “Status Bit Table” on page 10 for more details.
5
3631A–FLASH–04/06
3.8
Erase Suspend/Erase Resume
The Erase Suspend command allows the system to interrupt a sector erase operation and then
program or read data from a different sector within the memory. After the Erase Suspend command is given, the device requires a maximum time of 15 µs to suspend the erase operation.
After the erase operation has been suspended, the system can then read data or program data
to any other sector within the device. An address is not required during the Erase Suspend command. During a sector erase suspend, another sector cannot be erased. To resume the sector
erase operation, the system must write the Erase Resume command. The Erase Resume command is a one-bus cycle command. The device also supports an erase suspend during a
complete chip erase. While the chip erase is suspended, the user can read from any sector
within the memory that is protected. The command sequence for a chip erase suspend and a
sector erase suspend are the same.
3.9
Program Suspend/Program Resume
The Program Suspend command allows the system to interrupt a programming operation and
then read data from a different word within the memory. After the Program Suspend command is
given, the device requires a maximum of 10 µs to suspend the programming operation. After the
programming operation has been suspended, the system can then read from any other word
within the device. An address is not required during the program suspend operation. To resume
the programming operation, the system must write the Program Resume command. The
program suspend and resume are one-bus cycle commands. The command sequence for the
erase suspend and program suspend are the same, and the command sequence for the erase
resume and program resume are the same.
3.10
128-Bit Protection Register
The AT49BV642D(T) contains a 128-bit register that can be used for security purposes in system design. The protection register is divided into two 64-bit blocks. The two blocks are
designated as block A and block B. The data in block A is non-changeable and is programmed
at the factory with a unique number. The data in block B is programmed by the user and can be
locked out such that data in the block cannot be reprogrammed. To program block B in the protection register, the four-bus cycle Program Protection Register command must be used as
shown in the “Command Definition Table” on page 11. To lock out block B, the four-bus cycle
lock protection register command must be used as shown in the Command Definition table. Data
bit D1 must be zero during the fourth bus cycle. All other data bits during the fourth bus cycle are
don’t cares. To determine whether block B is locked out, the status of Block B Protection command is given. If data bit D1 is zero, block B is locked. If data bit D1 is one, block B can be
reprogrammed. Please see the “Protection Register Addressing Table” on page 12 for the
address locations in the protection register. To read the protection register, the Product ID Entry
command is given followed by a normal read operation from an address within the protection
register. After determining whether block B is protected or not or reading the protection register,
the Product ID Exit command must be given prior to performing any other operation.
6
AT49BV642D(T)
3631A–FLASH–04/06
AT49BV642D(T)
3.11
Common Flash Interface (CFI)
Common Flash Interface (CFI) is a published, standardized data structure that may be read from
a Flash device. CFI allows system software to query the installed device to determine the configurations, various electrical and timing parameters, and functions supported by the device. CFI is
used to allow the system to learn how to interface to the Flash device most optimally. The two
primary benefits of using CFI are ease of upgrading and second source availability. The command to enter the CFI Query mode is a one-bus cycle command which requires writing data 98h
to address 55h. The CFI Query command can be written when the device is ready to read data
or can also be written when the part is in the product ID mode. Once in the CFI Query mode, the
system can read CFI data at the addresses given in the “Common Flash Interface Definition
Table” on page 24. To exit the CFI Query mode, the product ID exit command must be given.
3.12
Hardware Data Protection
Hardware features protect against inadvertent programs to the AT49BV642D(T) in the following
ways: (a) VCC sense: if VCC is below 1.8V (typical), the program function is inhibited. (b) VCC
power-on delay: once VCC has reached the VCC sense level, the device will automatically timeout 10 ms (typical) before programming. (c) Program inhibit: holding any one of OE low, CE high
or WE high inhibits program cycles. (d) VPP is less than VILPP.
3.13
Input Levels
While operating with a 2.65V to 3.6V power supply, the address inputs and control inputs (OE,
CE and WE) may be driven from 0 to 5.5V without adversely affecting the operation of the
device. The I/O lines can be driven from 0 to VCCQ + 0.6V.
3.14
Output Levels
For the AT49BV642D(T), output high levels are equal to VCCQ - 0.1V (not VCC). For 2.65V to
3.6V output levels, VCCQ must be tied to VCC.
7
3631A–FLASH–04/06
Figure 3-1.
Data Polling Algorithm
(Configuration Register = 00)
Figure 3-2.
START
START
Read I/O7 - I/O0
Addr = VA
Read I/O7 - I/O0
Addr = VA
NO
YES
I/O7 = 1?
I/O7 = Data?
YES
NO
NO
I/O3, I/O5 = 1?
I/O3, I/O5 = 1?
YES
Notes:
8
Program/Erase
Operation Not
Successful, Write
Product ID
Exit Command
YES
NO
Program/Erase
Operation Not
Successful, Write
Product ID
Exit Command
NO
YES
Read I/O7 - I/O0
Addr = VA
I/O7 = Data?
Data Polling Algorithm
(Configuration Register = 01)
Note:
Program/Erase
Operation
Successful,
Device in
Read Mode
Program/Erase
Operation
Successful,
Write Product ID
Exit Command
1. VA = Valid address for programming. During a sector
erase operation, a valid address is any sector
address within the sector being erased. During chip
erase, a valid address is any non-protected sector
address.
1. VA = Valid address for programming. During a sector
erase operation, a valid address is any sector
address within the sector being erased. During chip
erase, a valid address is any non-protected sector
address.
2. I/O7 should be rechecked even if I/O5 = “1” because
I/O7 may change simultaneously with I/O5.
AT49BV642D(T)
3631A–FLASH–04/06
AT49BV642D(T)
Figure 3-3.
Toggle Bit Algorithm
(Configuration Register = 00)
Figure 3-4.
START
START
Read I/O7 - I/O0
Read I/O7 - I/O0
Read I/O7 - I/O0
Read I/O7 - I/O0
Toggle Bit =
Toggle?
NO
Toggle Bit =
Toggle?
NO
I/O3, I/O5 = 1?
Read I/O7 - I/O0
Twice
Read I/O7 - I/O0
Twice
Toggle Bit =
Toggle?
NO
Note:
NO
YES
YES
Program/Erase
Operation Not
Successful, Write
Product ID
Exit Command
I/O3, I/O5 = 1?
YES
YES
Toggle Bit =
Toggle?
NO
YES
YES
NO
Toggle Bit Algorithm
(Configuration Register = 01)
Program/Erase
Operation Not
Successful, Write
Product ID
Exit Command
Program/Erase
Operation
Successful,
Device in
Read Mode
1. The system should recheck the toggle bit even if
I/O5 = “1” because the toggle bit may stop toggling
as I/O5 changes to “1”.
Note:
Program/Erase
Operation
Successful,
Write Product ID
Exit Command
1. The system should recheck the toggle bit even if
I/O5 = “1” because the toggle bit may stop toggling
as I/O5 changes to “1”.
9
3631A–FLASH–04/06
4. Status Bit Table
Status Bit
I/O7
I/O7
I/O6
I/O5(1)
I/O3(2)
I/O2
00
01
00/01
00/01
00/01
00/01
I/O7
0
TOGGLE
0
0
1
Erasing
0
0
TOGGLE
0
0
TOGGLE
Erase Suspended & Read
Erasing Sector
1
1
1
0
0
TOGGLE
Erase Suspended & Read
Non-erasing Sector
DATA
DATA
DATA
DATA
DATA
DATA
Erase Suspended & Program
Non-erasing Sector
I/O7
0
TOGGLE
0
0
TOGGLE
Erase Suspended & Program
Suspended and Reading from
Non-suspended Sectors
DATA
DATA
DATA
DATA
DATA
DATA
Program Suspended & Read
Programming Sector
I/O7
1
1
0
0
TOGGLE
Program Suspended & Read
Non-programming Sector
DATA
DATA
DATA
DATA
DATA
DATA
Configuration Register
Programming
Notes:
10
1. I/O5 switches to a “1” when a program or an erase operation has exceeded the maximum time limits or when a program or
sector erase operation is performed on a protected sector.
2. I/O3 switches to a “1” when the VPP level is not high enough to successfully perform program and erase operations.
AT49BV642D(T)
3631A–FLASH–04/06
AT49BV642D(T)
5. Command Definition Table
1st Bus
Cycle
Bus
Cycles
Addr
Data
Read
1
Addr
DOUT
Chip Erase
6
555
AA
Command Sequence
Sector Erase
Word Program
Dual-Word Program
(4)
2nd Bus
Cycle
3rd Bus
Cycle
4th Bus
Cycle
5th Bus
Cycle
6th Bus
Cycle
Addr
Data
Addr
Data
Addr
Data
Addr
Data
Addr
Data
AAA(2)
55
555
80
555
AA
AAA
55
555
10
6
555
AA
AAA
55
555
80
555
AA
4
555
AA
AAA
55
555
A0
Addr
DIN
AAA
55
SA
(3)
30
5
555
AA
AAA
55
555
E0
Addr0
DIN0
Addr1
DIN1
Enter Single-pulse Program
Mode
6
555
AA
AAA
55
555
80
555
AA
AAA
55
555
A0
Single-pulse Word Program
Mode
1
Addr
DIN
Sector Lockdown(5)
6
555
AA
AAA
55
555
80
555
AA
AAA
55
SA(3)(5)
60
Erase/Program Suspend
1
xxx
B0
Erase/Program Resume
1
xxx
30
Product ID Entry
3
555
AA
AAA
55
555
90
(7)
3
555
AA
AAA
55
555
F0(8)
Product ID Exit(7)
1
xxx
F0(8)
Program Protection
Register – Block B
4
555
AA
AAA
55
555
C0
Addr(9)
DIN
Lock Protection
Register – Block B
4
555
AA
AAA
55
555
C0
80
X0
Status of Block B
Protection
4
555
AA
AAA
55
555
90
80
DOUT(10)
Set Configuration Register
4
555
AA
AAA
55
555
D0
xxx
00/01(11)
CFI Query
1
X55
98
(6)
Product ID Exit
Notes:
1. The DATA FORMAT in each bus cycle is as follows: I/O15 - I/O8 (Don’t Care); I/O7 - I/O0 (Hex). The ADDRESS FORMAT in
each bus cycle is as follows: A11 - A0 (Hex), A11 - A21 (Don’t Care).
2. Since A11 is a Don’t Care, AAA can be replaced with 2AA.
3. SA = sector address. Any word address within a sector can be used to designate the sector address (see pages 13 - 16
for details).
4. The fast programming option enables the user to program two words in parallel only when VPP = 10V. The addresses, Addr0
and Addr1, of the two words, DIN0 and DIN1, must only differ in address A0. This command should be used for manufacturing
purpose only.
5. Once a sector is in the lockdown mode, the data in the protected sector cannot be changed, unless the chip is reset or power
cycled.
6. During the fourth bus cycle, the manufacturer code is read from address 00000H, the device code is read from address
00001H, and the data in the protection register is read from addresses 000081H - 000088H.
7. Either one of the Product ID Exit commands can be used.
8. Bytes of data other than F0 may be used to exit the product ID mode. However, it is recommended that F0 be used.
9. Any address within the user programmable register region. Please see “Protection Register Addressing Table” on page 12.
10. If data bit D1 is “0”, block B is locked. If data bit D1 is “1”, block B can be reprogrammed.
11. The default state (after power-up) of the configuration register is “00”.
11
3631A–FLASH–04/06
6. Absolute Maximum Ratings*
*NOTICE:
Temperature under Bias ................................ -55°C to +125°C
Storage Temperature ..................................... -65°C to +150°C
All Input Voltages Except VPP
(including NC Pins)
with Respect to Ground ...................................-0.6V to +6.25V
VPP Input Voltage
with Respect to Ground ......................................... 0V to 10.0V
Stresses beyond those listed under “Absolute
Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and
functional operation of the device at these or any
other conditions beyond those indicated in the
operational sections of this specification is not
implied. Exposure to absolute maximum rating
conditions for extended periods may affect device
reliability.
All Output Voltages
with Respect to Ground ...........................-0.6V to VCCQ + 0.6V
7. Protection Register Addressing Table
Word
Use
Block
A7
A6
A5
A4
A3
A2
A1
A0
0
Factory
A
1
0
0
0
0
0
0
1
1
Factory
A
1
0
0
0
0
0
1
0
2
Factory
A
1
0
0
0
0
0
1
1
3
Factory
A
1
0
0
0
0
1
0
0
4
User
B
1
0
0
0
0
1
0
1
5
User
B
1
0
0
0
0
1
1
0
6
User
B
1
0
0
0
0
1
1
1
7
User
B
1
0
0
0
1
0
0
0
Note:
12
All address lines not specified in the above table must be “0” when accessing the protection register, i.e. A21 -A8 = 0.
AT49BV642D(T)
3631A–FLASH–04/06
AT49BV642D(T)
8. Memory Organization –
AT49BV642D
8. Memory Organization –
AT49BV642D (Continued)
x16
Size (Words)
Address Range
(A21 - A0)
SA0
4K
00000 - 00FFF
SA1
4K
01000 - 01FFF
SA2
4K
02000 - 02FFF
SA3
4K
03000 - 03FFF
SA4
4K
04000 - 04FFF
SA5
4K
05000 - 05FFF
SA6
4K
06000 - 06FFF
SA7
4K
07000 - 07FFF
SA8
32K
08000 - 0FFFF
SA9
32K
10000 - 17FFF
SA10
32K
18000 - 1FFFF
SA11
32K
20000 - 27FFF
SA12
32K
28000 - 2FFFF
SA13
32K
30000 - 37FFF
SA14
32K
38000 - 3FFFF
SA15
32K
40000 - 47FFF
SA16
32K
48000 - 4FFFF
SA17
32K
50000 - 57FFF
SA18
32K
58000 - 5FFFF
SA19
32K
60000 - 67FFF
SA20
32K
68000 - 6FFFF
SA21
32K
70000 - 77FFF
SA22
32K
78000 - 7FFFF
SA23
32K
80000 - 87FFF
SA24
32K
88000 - 8FFFF
SA25
32K
90000 - 97FFF
SA26
32K
98000 - 9FFFF
SA27
32K
A0000 - A7FFF
SA28
32K
A8000 - AFFFF
SA29
32K
B0000 - B7FFF
SA30
32K
B8000 - BFFFF
SA31
32K
C0000 - C7FFF
SA32
32K
C8000 - CFFFF
Sector
x16
Size (Words)
Address Range
(A21 - A0)
SA33
32K
D0000 - D7FFF
SA34
32K
D8000 - DFFFF
SA35
32K
E0000 - E7FFF
SA36
32K
E8000 - EFFFF
SA37
32K
F0000 - F7FFF
SA38
32K
F8000 - FFFFF
SA39
32K
100000 - 107FFF
SA40
32K
108000 - 10FFFF
SA41
32K
110000 - 117FFF
SA42
32K
118000 - 11FFFF
SA43
32K
120000 - 127FFF
SA44
32K
128000 - 12FFFF
SA45
32K
130000 - 137FFF
SA46
32K
138000 - 13FFFF
SA47
32K
140000 - 147FFF
SA48
32K
148000 - 14FFFF
SA49
32K
150000 - 157FFF
SA50
32K
158000 - 15FFFF
SA51
32K
160000 - 167FFF
SA52
32K
168000 - 16FFFF
SA53
32K
170000 - 177FFF
SA54
32K
178000 - 17FFFF
SA55
32K
180000 - 187FFF
SA56
32K
188000 - 18FFFF
SA57
32K
190000 - 197FFF
SA58
32K
198000 - 19FFFF
SA59
32K
1A0000 - 1A7FFF
SA60
32K
1A8000 - 1AFFFF
SA61
32K
1B0000 - 1B7FFF
SA62
32K
1B8000 - 1BFFFF
SA63
32K
1C0000 - 1C7FFF
SA64
32K
1C8000 - 1CFFFF
SA65
32K
1D0000 - 1D7FFF
Sector
13
3631A–FLASH–04/06
8. Memory Organization –
AT49BV642D (Continued)
8. Memory Organization –
AT49BV642D (Continued)
x16
x16
Size (Words)
Address Range
(A21 - A0)
Sector
Size (Words)
Address Range
(A21 - A0)
SA66
32K
1D8000 - 1DFFFF
SA100
32K
2E8000 - 2EFFFF
SA67
32K
1E0000 - 1E7FFF
SA101
32K
2F0000 - 2F7FFF
SA68
32K
1E8000 - 1EFFFF
SA102
32K
2F8000 - 2FFFFF
SA69
32K
1F0000 - 1F7FFF
SA103
32K
300000 - 307FFF
SA70
32K
1F8000 - 1FFFFF
SA104
32K
308000 - 30FFFF
SA71
32K
200000 - 207FFF
SA105
32K
310000 - 317FFF
SA72
32K
208000 - 20FFFF
SA106
32K
318000 - 31FFFF
SA73
32K
210000 - 217FFF
SA107
32K
320000 - 327FFF
SA74
32K
218000 - 21FFFF
SA108
32K
328000 - 32FFFF
SA75
32K
220000 - 227FFF
SA109
32K
330000 - 337FFF
SA76
32K
228000 - 22FFFF
SA110
32K
338000 - 33FFFF
SA77
32K
230000 - 237FFF
SA111
32K
340000 - 347FFF
SA78
32K
238000 - 23FFFF
SA112
32K
348000 - 34FFFF
SA79
32K
240000 - 247FFF
SA113
32K
350000 - 357FFF
SA80
32K
248000 - 24FFFF
SA114
32K
358000 - 35FFFF
SA81
32K
250000 - 257FFF
SA115
32K
360000 - 367FFF
SA82
32K
258000 - 25FFFF
SA116
32K
368000 - 36FFFF
SA83
32K
260000 - 267FFF
SA117
32K
370000 - 377FFF
SA84
32K
268000 - 26FFFF
SA118
32K
378000 - 37FFFF
SA85
32K
270000 - 277FFF
SA119
32K
380000 - 387FFF
SA86
32K
278000 - 27FFFF
SA120
32K
388000 - 38FFFF
SA87
32K
280000 - 287FFF
SA121
32K
390000 - 397FFF
SA88
32K
288000 - 28FFFF
SA122
32K
398000 - 39FFFF
SA89
32K
290000 - 297FFF
SA123
32K
3A0000 - 3A7FFF
SA90
32K
298000 - 29FFFF
SA124
32K
3A8000 - 3AFFFF
SA91
32K
2A0000 - 2A7FFF
SA125
32K
3B0000 - 3B7FFF
SA92
32K
2A8000 - 2AFFFF
SA126
32K
3B8000 - 3BFFFF
SA93
32K
2B0000 - 2B7FFF
SA127
32K
3C0000 - 3C7FFF
SA94
32K
2B8000 - 2BFFFF
SA128
32K
3C8000 - 3CFFFF
SA95
32K
2C0000 - 2C7FFF
SA129
32K
3D0000 - 3D7FFF
SA96
32K
2C8000 - 2CFFFF
SA130
32K
3D8000 - 3DFFFF
SA97
32K
2D0000 - 2D7FFF
SA131
32K
3E0000 - 3E7FFF
SA98
32K
2D8000 - 2DFFFF
SA132
32K
3E8000 - 3EFFFF
SA99
32K
2E0000 - 2E7FFF
SA133
32K
3F0000 - 3F7FFF
SA134
32K
3F8000 - 3FFFFF
Sector
14
AT49BV642D(T)
3631A–FLASH–04/06
AT49BV642D(T)
9. Memory Organization –
AT49BV642DT
9. Memory Organization –
AT49BV642DT (Continued)
x16
Size
(Words)
Address Range
(A21 - A0)
SA0
32K
00000 - 07FFF
SA1
32K
SA2
x16
Size
(Words)
Address Range
(A21 - A0)
SA36
32K
120000 - 127FFF
08000 - 0FFFF
SA37
32K
128000 - 12FFFF
32K
10000 - 17FFF
SA38
32K
130000 - 137FFF
SA3
32K
18000 - 1FFFF
SA39
32K
138000 - 13FFFF
SA4
32K
20000 - 27FFF
SA40
32K
140000 - 147FFF
SA5
32K
28000 - 2FFFF
SA41
32K
148000 - 14FFFF
SA6
32K
30000 - 37FFF
SA42
32K
150000 - 157FFF
SA7
32K
38000 - 3FFFF
SA43
32K
158000 - 15FFFF
SA8
32K
40000 - 47FFF
SA44
32K
160000 - 167FFF
SA9
32K
48000 - 4FFFF
SA45
32K
168000 - 16FFFF
SA10
32K
50000 - 57FFF
SA46
32K
170000 - 177FFF
SA11
32K
58000 - 5FFFF
SA47
32K
178000 - 17FFFF
SA12
32K
60000 - 67FFF
SA48
32K
180000 - 187FFF
SA13
32K
68000 - 6FFFF
SA49
32K
188000 - 18FFFF
SA14
32K
70000 - 77FFF
SA50
32K
190000 - 197FFF
SA15
32K
78000 - 7FFFF
SA51
32K
198000 - 19FFFF
SA16
32K
80000 - 87FFF
SA52
32K
1A0000 - 1A7FFF
SA17
32K
88000 - 8FFFF
SA53
32K
1A8000 - 1AFFFF
SA18
32K
90000 - 97FFF
SA54
32K
1B0000 - 1B7FFF
SA19
32K
98000 - 9FFFF
SA55
32K
1B8000 - 1BFFFF
SA20
32K
A0000 - A7FFF
SA56
32K
1C0000 - 1C7FFF
SA21
32K
A8000 - AFFFF
SA57
32K
1C8000 - 1CFFFF
SA22
32K
B0000 - B7FFF
SA58
32K
1D0000 - 1D7FFF
SA23
32K
B8000 - BFFFF
SA59
32K
1D8000 - 1DFFFF
SA24
32K
C0000 - C7FFF
SA60
32K
1E0000 - 1E7FFF
SA25
32K
C8000 - CFFFF
SA61
32K
1E8000 - 1EFFFF
SA26
32K
D0000 - D7FFF
SA62
32K
1F0000 - 1F7FFF
SA27
32K
D8000 - DFFFF
SA63
32K
1F8000 - 1FFFFF
SA28
32K
E0000 - E7FFF
SA64
32K
200000 - 207FFF
SA29
32K
E8000 - EFFFF
SA65
32K
208000 - 20FFFF
SA30
32K
F0000 - F7FFF
SA66
32K
210000 - 217FFF
SA31
32K
F8000 - FFFFF
SA67
32K
218000 - 21FFFF
SA32
32K
100000 - 107FFF
SA68
32K
220000 - 227FFF
SA33
32K
108000 - 10FFFF
SA69
32K
228000 - 22FFFF
SA34
32K
110000 - 117FFF
SA70
32K
230000 - 237FFF
SA35
32K
118000 - 11FFFF
SA71
32K
238000 - 23FFFF
Sector
Sector
15
3631A–FLASH–04/06
9. Memory Organization –
AT49BV642DT (Continued)
9. Memory Organization –
AT49BV642DT (Continued)
x16
Size
(Words)
Address Range
(A21 - A0)
SA72
32K
SA73
x16
Sector
Size
(Words)
Address Range
(A21 - A0)
240000 - 247FFF
SA104
32K
340000 - 347FFF
32K
248000 - 24FFFF
SA105
32K
348000 - 34FFFF
SA74
32K
250000 - 257FFF
SA106
32K
350000 - 357FFF
SA75
32K
258000 - 25FFFF
SA107
32K
358000 - 35FFFF
SA76
32K
260000 - 267FFF
SA108
32K
360000 - 367FFF
SA77
32K
268000 - 26FFFF
SA109
32K
368000 - 36FFFF
SA78
32K
270000 - 277FFF
SA110
32K
370000 - 377FFF
SA79
32K
278000 - 27FFFF
SA111
32K
378000 - 37FFFF
SA80
32K
280000 - 287FFF
SA112
32K
380000 - 387FFF
SA81
32K
288000 - 28FFFF
SA113
32K
388000 - 38FFFF
SA82
32K
290000 - 297FFF
SA114
32K
390000 - 397FFF
SA83
32K
298000 -29FFFF
SA115
32K
398000 - 39FFFF
SA84
32K
2A0000 - 2A7FFF
SA116
32K
3A0000 - 3A7FFF
SA85
32K
2A8000 - 2AFFFF
SA117
32K
3A8000 - 3AFFFF
SA86
32K
2B0000 - 2B7FFF
SA118
32K
3B0000 - 3B7FFF
SA87
32K
2B8000 - 2BFFFF
SA119
32K
3B8000 - 3BFFFF
SA88
32K
2C0000 - 2C7FFF
SA120
32K
3C0000 - 3C7FFF
SA89
32K
2C8000 - 2CFFFF
SA121
32K
3C8000 - 3CFFFF
SA90
32K
2D0000 - 2D7FFF
SA122
32K
3D0000 - 3D7FFF
SA91
32K
2D8000 - 2DFFFF
SA123
32K
3D8000 - 3DFFFF
SA92
32K
2E0000 - 2E7FFF
SA124
32K
3E0000 - 3E7FFF
SA93
32K
2E8000 - 2EFFFF
SA125
32K
3E8000 - 3EFFFF
SA94
32K
2F0000 - 2F7FFF
SA126
32K
3F0000 - 3F7FFF
SA95
32K
2F8000 - 2FFFFF
SA127
4K
3F8000 - 3F8FFF
SA96
32K
300000 - 307FFF
SA128
4K
3F9000 - 3F9FFF
SA97
32K
308000 - 30FFFF
SA129
4K
3FA000 - 3FAFFF
SA98
32K
310000 - 317FFF
SA130
4K
3FB000 - 3FBFFF
SA99
32K
318000 - 31FFFF
SA131
4K
3FC000 - 3FCFFF
SA100
32K
320000 - 327FFF
SA132
4K
3FD000 - 3FDFFF
SA101
32K
328000 - 32FFFF
SA133
4K
3FE000 - 3FEFFF
SA102
32K
330000 - 337FFF
SA134
4K
3FF000 - 3FFFFF
SA103
32K
338000 - 33FFFF
Sector
16
AT49BV642D(T)
3631A–FLASH–04/06
AT49BV642D(T)
10. DC and AC Operating Range
AT49BV642D(T) - 70
Operating Temperature (Case)
Industrial
-40°C - 85°C
VCC Power Supply
2.7V - 3.6V
11. Operating Modes
Mode
CE
OE
WE
RESET
VPP(1)
Ai
I/O
Read
VIL
VIL
VIH
VIH
X(2)
Ai
DOUT
Program/Erase(3)
VIL
VIH
VIL
VIH
VIHPP(4)
Ai
DIN
X
High Z
Standby/Program Inhibit
(2)
VIH
X
X
VIH
X
X
X
VIH
VIH
X
X
VIL
X
VIH
X
X
X
X
X
VILPP(5)
Output Disable
X
VIH
X
VIH
X
Reset
X
X
X
VIL
X
Program Inhibit
Software Product
Identification
Notes:
1.
2.
3.
4.
5.
6.
VIH
High Z
X
High Z
A0 = VIL, A1 - A21 = VIL
Manufacturer Code(6)
A0 = VIH, A1 - A21 = VIL
Device Code(6)
The VPP pin can be tied to VCC. For faster program operations, VPP can be set to 9.5V ± 0.5V.
X can be VIL or VIH.
Refer to program cycle waveforms on page 21.
VIHPP (min) = 1.65V.
VILPP (max) = 0.4V.
Manufacturer Code: 001FH; Device Code: 01D6H - AT49BV642D; 01D2H - AT49BV642DT.
17
3631A–FLASH–04/06
12. DC Characteristics
Symbol
Parameter
Condition
ILI
Input Load Current
ILO
Max
Units
VIN = 0V to VCC
2
µA
Output Leakage Current
VI/O = 0V to VCC
2
µA
ISB
VCC Standby Current CMOS
CE = VCCQ - 0.3V to VCC
15
25
µA
ICC(1)
VCC Active Read Current
f = 5 MHz; IOUT = 0 mA
10
15
mA
ICC1
VCC Programming Current
25
mA
VIL
Input Low Voltage
0.6
V
VIH
Input High Voltage
VOL
Output Low Voltage
IOL = 2.1 mA
Output High Voltage
IOH = -100 µA
VOH
Note:
Min
Typ
VCCQ - 0.6
V
0.45
V
VCCQ - 0.1
V
1. In the erase mode, ICC is 25 mA.
13. Input Test Waveforms and Measurement Level
2.0V
AC
DRIVING
LEVELS
1.5V
AC
MEASUREMENT
LEVEL
0.6V
tR, tF < 5 ns
14. Output Test Load
VCCQ
1.8K
OUTPUT
PIN
1.3K
30 pF
15. Pin Capacitance
f = 1 MHz, T = 25°C(1)
Typ
Max
Units
Conditions
CIN
4
6
pF
VIN = 0V
COUT
8
12
pF
VOUT = 0V
Note:
18
1. This parameter is characterized and is not 100% tested.
AT49BV642D(T)
3631A–FLASH–04/06
AT49BV642D(T)
16. AC Read Characteristics
Symbol
Parameter
Min
Max
tRC
Read Cycle Time
tACC
Access, Address to Data Valid
70
ns
tCE
Access, CE to Data Valid
70
ns
tOE
OE to Data Valid
20
ns
tDF
CE, OE High to Data Float
25
ns
tOH
Output Hold from OE, CE or Address, whichever Occurs First
tRO
RESET to Output Delay
70
Units
ns
0
ns
100
ns
17. Asynchronous Read Cycle Waveform(1)(2)(3)
tRC
A0 - A21
ADDRESS VALID
CE
tCE
tOE
OE
tDF
tOH
tACC
tRO
RESET
I/O0 - I/O15
Notes:
HIGH Z
OUTPUT
VALID
1. CE may be delayed up to tACC - tCE after the address transition without impact on tACC.
2. OE may be delayed up to tCE - tOE after the falling edge of CE without impact on tCE or by tACC - tOE after an address change
without impact on tACC.
3. tDF is specified from OE or CE, whichever occurs first (CL = 5 pF).
19
3631A–FLASH–04/06
18. AC Word Load Characteristics
Symbol
Parameter
Min
Max
Units
tAS, tOES
Address, OE Setup Time
0
ns
tAH
Address Hold Time
25
ns
tCS
Chip Select Setup Time
0
ns
tCH
Chip Select Hold Time
0
ns
tWP
Write Pulse Width (WE or CE)
25
ns
tWPH
Write Pulse Width High
15
ns
tDS
Data Setup Time
25
ns
tDH, tOEH
Data, OE Hold Time
0
ns
19. AC Word Load Waveforms
19.1
WE Controlled
19.2
CE Controlled
20
AT49BV642D(T)
3631A–FLASH–04/06
AT49BV642D(T)
20. Program Cycle Characteristics
Symbol
Parameter
tBP
Min
Typ
Max
Units
Word Programming Time
10
120
µs
tBPD
Word Programming Time in Dual Programming Mode
5
60
µs
tAS
Address Setup Time
0
ns
tAH
Address Hold Time
25
ns
tDS
Data Setup Time
25
ns
tDH
Data Hold Time
0
ns
tWP
Write Pulse Width
25
ns
tWPH
Write Pulse Width High
15
ns
tWC
Write Cycle Time
70
ns
tRP
Reset Pulse Width
500
ns
tEC
Chip Erase Cycle Time
64
tSEC1
Sector Erase Cycle Time (4K Word Sectors)
0.1
2.0
seconds
tSEC2
Sector Erase Cycle Time (32K Word Sectors)
0.5
6.0
seconds
tES
Erase Suspend Time
15
µs
tPS
Program Suspend Time
10
µs
seconds
21. Program Cycle Waveforms
PROGRAM CYCLE
OE
CE
tWP
tBP
tWPH
WE
tAS
A0 - A21
tAH
tDH
555
DATA
555
AAA
tWC
555
ADDRESS
tDS
55
AA
INPUT
DATA
A0
AA
22. Sector or Chip Erase Cycle Waveforms
OE
(1)
CE
tWP
tWPH
WE
tAS
A0-A21
tAH
555
Notes:
555
555
AAA
tWC
DATA
tDH
Note 2
AAA
tEC
tDS
AA
55
80
AA
55
Note 3
WORD 0
WORD 1
WORD 2
WORD 3
WORD 4
WORD 5
1. OE must be high only when WE and CE are both low.
2. For chip erase, the address should be 555. For sector erase, the address depends on what sector is to be erased.
(See note 3 under “Command Definition Table” on page 11.)
3. For chip erase, the data should be 10H, and for sector erase, the data should be 30H.
21
3631A–FLASH–04/06
23. Data Polling Characteristics
Symbol
Parameter
tDH
Data Hold Time
tOEH
OE Hold Time
Typ
Max
ns
10
ns
OE to Output Delay
tWR
Units
10
(2)
tOE
Notes:
Min
ns
Write Recovery Time
0
ns
1. These parameters are characterized and not 100% tested.
2. See tOE spec on page 19.
24. Data Polling Waveforms
WE
CE
OE
I/O7
A0-A21
25. Toggle Bit Characteristics(1)
Symbol
Parameter
tDH
Data Hold Time
tOEH
OE Hold Time
Min
Typ
Max
Units
10
ns
10
ns
(2)
tOE
OE to Output Delay
tOEHP
OE High Pulse
50
ns
tWR
Write Recovery Time
0
ns
Notes:
ns
1. These parameters are characterized and not 100% tested.
2. See tOE spec on page 19.
26. Toggle Bit Waveforms(1)(2)(3)
Notes:
22
1. Toggling either OE or CE or both OE and CE will operate toggle bit.
The tOEHP specification must be met by the toggling input(s).
2. Beginning and ending state of I/O6 will vary.
3. Any address location may be used but the address should not vary.
AT49BV642D(T)
3631A–FLASH–04/06
AT49BV642D(T)
27. Software Product Identification Entry(1)
LOAD DATA AA
TO
ADDRESS 555
LOAD DATA 55
TO
ADDRESS AAA
LOAD DATA 90
TO
ADDRESS 555
ENTER PRODUCT
IDENTIFICATION
MODE(2)(3)(5)
28. Software Product Identification Exit(1)(6)
LOAD DATA AA
TO
ADDRESS 555
LOAD DATA 55
TO
ADDRESS AAA
OR
LOAD DATA F0
TO
ANY ADDRESS
EXIT PRODUCT
IDENTIFICATION
MODE(4)
LOAD DATA F0
TO
ADDRESS 555
EXIT PRODUCT
IDENTIFICATION
MODE(4)
Notes:
1.
2.
3.
4.
5.
Data Format: I/O15 - I/O8 (Don’t Care); I/O7 - I/O0 (Hex) Address Format: A11 - A0 (Hex), and A11 - A21 (Don’t Care).
A1 - A21 = VIL. Manufacturer Code is read for A0 = VIL; Device Code is read for A0 = VIH.
The device does not remain in identification mode if powered down.
The device returns to standard operation mode.
Manufacturer Code: 001FH(x16)
Device Code: 01D6H – AT49BV642D;
01D2H – AT49BV642DT.
6. Either one of the Product ID Exit commands can be used.
23
3631A–FLASH–04/06
29. Common Flash Interface Definition Table
24
Address
Data
Comments
10h
0051h
“Q”
11h
0052h
“R”
12h
0059h
“Y”
13h
0002h
14h
0000h
15h
0041h
16h
0000h
17h
0000h
18h
0000h
19h
0000h
1Ah
0000h
1Bh
0027h
VCC min write/erase
1Ch
0036h
VCC max write/erase
1Dh
0090h
VPP min voltage
1Eh
00A0h
VPP max voltage
1Fh
0004h
Typ word write – 10 µs
20h
0002h
Typ dual-word program time – 5 µs
21h
0009h
Typ sector erase – 500 ms
22h
0010h
Typ chip erase – 64,300 ms
23h
0004h
Max word write/typ time
24h
0004h
Max dual-word program time/typ time
25h
0004h
Max sector erase/typ sector erase
26h
0004h
Max chip erase/ typ chip erase
27h
0017h
Device size
28h
0001h
x16 device
29h
0000h
x16 device
2Ah
0002h
Max number of bytes in multiple byte write = 4
2Bh
0000h
Max number of bytes in multiple byte write = 4
2Ch
0002h
2 regions, x = 2
2Dh
0007h
8K bytes, Y = 7
2Eh
0000h
8K bytes, Y = 7
2Fh
0020h
8K bytes, Z = 32
30h
0000h
8K bytes, Z = 32
31h
007Eh
64K bytes, Y = 126
32h
0000h
64K bytes, Y = 126
33h
0000h
64K bytes, Z = 256
34h
0001h
64K bytes, Z = 256
AT49BV642D(T)
3631A–FLASH–04/06
AT49BV642D(T)
29. Common Flash Interface Definition Table (Continued)
Address
Data
Comments
VENDOR SPECIFIC EXTENDED QUERY
41h
0050h
“P”
42h
0052h
“R”
43h
0049h
“I”
44h
0031h
Major version number, ASCII
45h
0030h
Minor version number, ASCII
46h
0087h
Bit 0 – chip erase supported, 0 – no, 1 – yes
Bit 1 – erase suspend supported, 0 – no, 1 – yes
Bit 2 – program suspend supported, 0 – no, 1 – yes
Bit 3 – simultaneous operations supported, 0 – no, 1 – yes
Bit 4 – burst mode read supported, 0 – no, 1 – yes
Bit 5 – page mode read supported, 0 – no, 1 – yes
Bit 6 – queued erase supported, 0 – no, 1 – yes
Bit 7 – protection bits supported, 0 – no, 1 – yes
47h
0000h AT49BV642DT or
0001h AT49BV642D
Bit 0 – top (“0”) or bottom (“1”) boot block device
Undefined bits are “0”
48h
0000h
Bit 0 – 4 word linear burst with wrap around, 0 – no, 1 – yes
Bit 1 – 8 word linear burst with wrap around, 0 – no, 1 – yes
Bit 2 – continuos burst, 0 – no, 1 – yes
Undefined bits are “0”
49h
0000h
Bit 0 – 4 word page, 0 – no, 1 – yes
Bit 1 – 8 word page, 0 – no, 1 – yes
Undefined bits are “0”
4Ah
0080h
Location of protection register lock byte, the section's first byte
4Bh
0003h
# of bytes in the factory prog section of prot register – 2*n
4Ch
0003h
# of bytes in the user prog section of prot register – 2*n
25
3631A–FLASH–04/06
30. Ordering Information
30.1
tACC
(ns)
Green Package (Pb/Halide-free/RoHS Compliant)
ICC (mA)
Active
Standby
Ordering Code
Package
Operation Range
48T
Industrial
(-40° to 85° C)
AT49BV642D-70TU
70
15
0.025
AT49BV642DT-70TU
Package Type
48T
26
48-lead, Plastic Thin Small Outline Package (TSOP)
AT49BV642D(T)
3631A–FLASH–04/06
AT49BV642D(T)
31. Packaging Information
31.1
48T – TSOP
PIN 1
0º ~ 8º
c
Pin 1 Identifier
D1 D
L
b
e
L1
A2
E
A
GAGE PLANE
SEATING PLANE
COMMON DIMENSIONS
(Unit of Measure = mm)
A1
MIN
NOM
MAX
A
–
–
1.20
A1
0.05
–
0.15
SYMBOL
Notes:
1. This package conforms to JEDEC reference MO-142, Variation DD.
2. Dimensions D1 and E do not include mold protrusion. Allowable
protrusion on E is 0.15 mm per side and on D1 is 0.25 mm per side.
3. Lead coplanarity is 0.10 mm maximum.
NOTE
A2
0.95
1.00
1.05
D
19.80
20.00
20.20
D1
18.30
18.40
18.50
Note 2
E
11.90
12.00
12.10
Note 2
L
0.50
0.60
0.70
L1
0.25 BASIC
b
0.17
0.22
0.27
c
0.10
–
0.21
e
0.50 BASIC
10/18/01
R
2325 Orchard Parkway
San Jose, CA 95131
TITLE
48T, 48-lead (12 x 20 mm Package) Plastic Thin Small Outline
Package, Type I (TSOP)
DRAWING NO.
REV.
48T
B
27
3631A–FLASH–04/06
32. Revision History
28
Revision No.
History
Revision A – April 2006
•
Initial Release
AT49BV642D(T)
3631A–FLASH–04/06
Atmel Corporation
2325 Orchard Parkway
San Jose, CA 95131, USA
Tel: 1(408) 441-0311
Fax: 1(408) 487-2600
Regional Headquarters
Europe
Atmel Sarl
Route des Arsenaux 41
Case Postale 80
CH-1705 Fribourg
Switzerland
Tel: (41) 26-426-5555
Fax: (41) 26-426-5500
Asia
Room 1219
Chinachem Golden Plaza
77 Mody Road Tsimshatsui
East Kowloon
Hong Kong
Tel: (852) 2721-9778
Fax: (852) 2722-1369
Japan
9F, Tonetsu Shinkawa Bldg.
1-24-8 Shinkawa
Chuo-ku, Tokyo 104-0033
Japan
Tel: (81) 3-3523-3551
Fax: (81) 3-3523-7581
Atmel Operations
Memory
2325 Orchard Parkway
San Jose, CA 95131, USA
Tel: 1(408) 441-0311
Fax: 1(408) 436-4314
RF/Automotive
Theresienstrasse 2
Postfach 3535
74025 Heilbronn, Germany
Tel: (49) 71-31-67-0
Fax: (49) 71-31-67-2340
Microcontrollers
2325 Orchard Parkway
San Jose, CA 95131, USA
Tel: 1(408) 441-0311
Fax: 1(408) 436-4314
La Chantrerie
BP 70602
44306 Nantes Cedex 3, France
Tel: (33) 2-40-18-18-18
Fax: (33) 2-40-18-19-60
ASIC/ASSP/Smart Cards
1150 East Cheyenne Mtn. Blvd.
Colorado Springs, CO 80906, USA
Tel: 1(719) 576-3300
Fax: 1(719) 540-1759
Biometrics/Imaging/Hi-Rel MPU/
High Speed Converters/RF Datacom
Avenue de Rochepleine
BP 123
38521 Saint-Egreve Cedex, France
Tel: (33) 4-76-58-30-00
Fax: (33) 4-76-58-34-80
Zone Industrielle
13106 Rousset Cedex, France
Tel: (33) 4-42-53-60-00
Fax: (33) 4-42-53-60-01
1150 East Cheyenne Mtn. Blvd.
Colorado Springs, CO 80906, USA
Tel: 1(719) 576-3300
Fax: 1(719) 540-1759
Scottish Enterprise Technology Park
Maxwell Building
East Kilbride G75 0QR, Scotland
Tel: (44) 1355-803-000
Fax: (44) 1355-242-743
Literature Requests
www.atmel.com/literature
Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any
intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDITIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY
WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT
OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no
representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications
and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided
otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel’s products are not intended, authorized, or warranted for use
as components in applications intended to support or sustain life.
© Atmel Corporation 2006. All rights reserved. Atmel ®, logo and combinations thereof, Everywhere You Are ® and others, are
registered trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others.
Printed on recycled paper.
3631A–FLASH–04/06
xM