Features • • • • • • • • • • • • • • • • • • • • • • • • 80C51 Core Architecture 256 Bytes of On-chip RAM 2048 Bytes of On-chip ERAM 64K Bytes of On-chip Flash Memory – Data Retention: 10 Years at 85°C – Read/Write Cycle: 100K Boot Code Section with Independent Lock Bits 2K Bytes of On-chip Flash for Bootloader In-System Programming by On-Chip UART Boot Program and IAP Capability 2K Bytes of On-chip EEPROM Read/Write Cycle: 100K Integrated Power Monitor (POR: PFD) To Supervise Internal Power Supply 14-sources 4-level Interrupts Three 16-bit Timers/Counters Full Duplex UART Compatible 80C51 High-speed Architecture – In Standard Mode: 40 MHz (Vcc 3V to 5.5V, both Internal and external code execution) 60 MHz (Vcc 4.5V to 5.5V and Internal Code execution only) – In X2 mode (6 Clocks/machine cycle) 20 MHz (Vcc 3V to 5.5V, both Internal and external code execution) 30 MHz (Vcc 4.5V to 5.5V and Internal Code execution only) Five Ports: 32 + 4 Digital I/O Lines Five-channel 16-bit PCA with – PWM (8-bit) – High-speed Output – Timer and Edge Capture Double Data Pointer 21-bit WatchDog Timer (7 Programmable Bits) A 10-bit Resolution Analog to Digital Converter (ADC) with 8 Multiplexed Inputs SPI Interface (PLCC52 and VPFP64 packages only) On-chip Emulation Logic (Enhanced Hook System) Power Saving Modes – Idle Mode – Power-down Mode Power Supply: 3 volts to 5.5 volts Temperature Range: Industrial (-40° to +85°C) Packages: VQFP44, PLCC44, VQFP64, PLCC52 Enhanced 8-bit Microcontroller with 64KB Flash Memory AT89C51AC3 Description The AT89C51AC3 is a high performance Flash version of the 80C51 single chip 8-bit microcontrollers. In X2 mode a maximum external clock rate of 20 MHz reaches a 300 ns cycle time. Besides the AT89C51AC3 provides 64K Bytes of Flash memory including In-System Programming (ISP) and IAP, 2K Bytes Boot Flash Memory, 2K Bytes EEPROM and 2048 byte ERAM. Primary attention is paid to the reduction of the electro-magnetic emission of AT89C51AC3. Rev. 4383A–8051–10/04 T2 T2EX PCA ECI Vss Vcc TxD RxD Block Diagram XTAL1 RAM 256x8 UART XTAL2 ALE C51 CORE PSEN ERAM 2048 Flash Boot EE 64k x 8 loader PROM 2kx8 2kx8 PCA Timer2 IB-bus CPU EA Notes: 2 Emul Unit 10 bit ADC SPI Interface MOSI SCK MISO P4(2) P3 P2 INT1 INT0 T1 T0 RESET WR Parallel I/O Ports and Ext. Bus Watch Dog Port 0 Port 1 Port 2 Port 3 Port 4 P1(1) INT Ctrl P0 Timer 0 Timer 1 RD 1. 8 analog Inputs/8 Digital I/O 2. 5-Bit I/O Port AT89C51AC3 4383A–8051–10/04 AT89C51AC3 6 5 4 3 2 1 44 43 42 41 40 P1.3/AN3/CEX0 P1.2/AN2/ECI P1.1/AN1/T2EX P1.0/AN 0/T2 VAREF VAGND RESET VSS VCC XTAL1 XTAL2 Pin Configuration 7 8 9 10 11 12 13 14 15 16 17 39 38 37 36 35 34 33 32 31 30 29 PLCC44 ALE PSEN P0.7/AD7 P0.6/AD6 P0.5/AD5 P0.4/AD4 P0.3/AD3 P0.2/AD2 P0.1/AD1 P0.0/AD0 P2.0/A8 P1.3/AN3/CEX0 P1.2/AN2/ECI P1.1/AN1/T2EX P1.0/AN 0/T2 VAREF VAGND RESET VSS VCC XTAL1 XTAL2 P3.6/WR P3.7/RD P4.0 P4.1 P2.7/A15 P2.6/A14 P2.5/A13 P2.4/A12 P2.3/A11 P2.2/A10 P2.1/A9 18 19 20 21 22 23 24 25 26 27 28 P1.4/AN4/CEX1 P1.5/AN5/CEX2 P1.6/AN6/CEX3 P1.7/AN7/CEX4 EA P3.0/RxD P3.1/TxD P3.2/INT0 P3.3/INT1 P3.4/T0 P3.5/T1 44 43 42 41 40 39 38 37 36 35 34 P1.4/AN4/CEX1 P1.5/AN5/CEX2 P1.6/AN6/CEX3 P1.7/AN7/CEX4 EA P3.0/RxD P3.1/TxD P3.2/INT0 P3.3/INT1 P3.4/T0 P3.5/T1 2 33 32 3 4 30 1 5 6 31 VQFP44 7 8 29 28 27 9 26 25 10 24 23 11 ALE PSEN P0.7/AD7 P0.6/AD6 P0.5/AD5 P0.4 /AD4 P0.3 /AD3 P0.2 /AD2 P0.1 /AD1 P0.0 /AD0 P2.0/A8 P3.6/WR P3.7/RD P4.0 P4.1 P2.7/A15 P2.6/A14 P2.5/A13 P2.4/A12 P2.3/A11 P2.2/A10 P2.1/A9 12 13 14 15 16 17 18 19 20 21 22 3 4383A–8051–10/04 2 VCC XTAL1 XTAL2 VAGND RESET VSS TESTI VCC 3 1 52 51 50 49 48 47 46 9 45 10 44 11 43 12 13 42 14 41 PLCC52 ALE PSEN P0.7/AD7 P0.6/AD6 NC P0.5/AD5 P0.4 /AD4 P0.3 /AD3 P0.2 /AD2 P0.1 /AD1 15 40 39 16 38 17 37 18 36 19 35 P4.4/MOSI P0.0 /AD0 34 P2.0/A8 20 21 22 23 24 25 26 27 28 29 30 31 32 33 P3.6/WR P3.7/RD P4.0 P4.1 P2.7/A15 P2.6/A14 NC P3.1/TxD P3.2/INT0 P3.3/INT1 P3.4/T0 P3.5/T1/SS 5 4 P2.5/A13 P2.4/A12 P2.3/A11 P2.2/A10 P2.1/A9 P4.2/MISO P1.4/AN4/CEX1 P1.5/AN5/CEX2 P1.6/AN6/CEX3 P1.7/AN7/CEX4 EA NC P3.0/RxD P4.3/SCK 6 VAREF P1.3/AN3/CEX0 P1.2/AN2/ECI P1.1/AN1/T2EX P1.0/AN 0/T2 7 8 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 P1.3/AN3/CEX0 P1.2/AN2/ECI P1.1/AN1/T2EX P1.0/AN0/T2 VAREF VAGND RESET VSS VSS VSS TESTI VCC VCC VCC XTAL1 XTAL2 TESTI must be connected to VSS 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 VQFP64 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 NC ALE PSEN P0.7/AD7 P0.6/AD6 NC P0.5/AD5 NC NC P0.4/AD4 P0.3/AD3 P0.2/AD2 P0.1/AD1 P4.4/MOSI P0.0/AD0 P2.0/A8 P3.6/WR P3.7/RD P4.0 P4.1 P2.7/A15 P2.6/A14 NC NC NC NC P2.5/A13 P2.4/A12 P2.3/A11 P2.2/A10 P2.1/A9 P4.2/MISO 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 P1.4/AN4/CEX1 NC P1.5/AN5/CEX2 P1.6/AN6/CEX3 P1.7/AN7/CEX4 NC EA NC NC P3.0/RxD P4.3/SCK P3.1/TxD P3.2/INT0 P3.3/INT1 P3.4/T0 P3.5/T1/SS TESTI must be connected to VSS 4 AT89C51AC3 4383A–8051–10/04 AT89C51AC3 Pin Name Type Description VSS GND Circuit ground TESTI I VCC Must be connected to VSS Supply Voltage VAREF Reference Voltage for ADC VAGND Reference Ground for ADC P0.0:7 I/O Port 0: Is an 8-bit open drain bi-directional I/O port. Port 0 pins that have 1’s written to them float, and in this state can be used as high-impedance inputs. Port 0 is also the multiplexed low-order address and data bus during accesses to external Program and Data Memory. In this application it uses strong internal pull-ups when emitting 1’s. Port 0 also outputs the code Bytes during program validation. External pull-ups are required during program verification. P1.0:7 I/O Port 1: Is an 8-bit bi-directional I/O port with internal pull-ups. Port 1 pins can be used for digital input/output or as analog inputs for the Analog Digital Converter (ADC). Port 1 pins that have 1’s written to them are pulled high by the internal pull-up transistors and can be used as inputs in this state. As inputs, Port 1 pins that are being pulled low externally will be the source of current (IIL, see section "Electrical Characteristic") because of the internal pull-ups. Port 1 pins are assigned to be used as analog inputs via the ADCCF register (in this case the internal pull-ups are disconnected). As a secondary digital function, port 1 contains the Timer 2 external trigger and clock input; the PCA external clock input and the PCA module I/O. P1.0/AN0/T2 Analog input channel 0, External clock input for Timer/counter2. P1.1/AN1/T2EX Analog input channel 1, Trigger input for Timer/counter2. P1.2/AN2/ECI Analog input channel 2, PCA external clock input. P1.3/AN3/CEX0 Analog input channel 3, PCA module 0 Entry of input/PWM output. P1.4/AN4/CEX1 Analog input channel 4, PCA module 1 Entry of input/PWM output. P1.5/AN5/CEX2 Analog input channel 5, PCA module 2 Entry of input/PWM output. P1.6/AN6/CEX3 Analog input channel 6, PCA module 3 Entry of input/PWM output. P1.7/AN7/CEX4 Analog input channel 7, PCA module 4 Entry ot input/PWM output. Port 1 receives the low-order address byte during EPROM programming and program verification. It can drive CMOS inputs without external pull-ups. P2.0:7 I/O Port 2: Is an 8-bit bi-directional I/O port with internal pull-ups. Port 2 pins that have 1’s written to them are pulled high by the internal pull-ups and can be used as inputs in this state. As inputs, Port 2 pins that are being pulled low externally will be a source of current (IIL, see section "Electrical Characteristic") because of the internal pull-ups. Port 2 emits the high-order address byte during accesses to the external Program Memory and during accesses to external Data Memory that uses 16-bit addresses (MOVX @DPTR). In this application, it uses strong internal pull-ups when emitting 1’s. During accesses to external Data Memory that use 8 bit addresses (MOVX @Ri), Port 2 transmits the contents of the P2 special function register. It also receives high-order addresses and control signals during program validation. It can drive CMOS inputs without external pull-ups. 5 4383A–8051–10/04 Pin Name Type P3.0:7 I/O Description Port 3: Is an 8-bit bi-directional I/O port with internal pull-ups. Port 3 pins that have 1’s written to them are pulled high by the internal pull-up transistors and can be used as inputs in this state. As inputs, Port 3 pins that are being pulled low externally will be a source of current (IIL, see section "Electrical Characteristic") because of the internal pull-ups. The output latch corresponding to a secondary function must be programmed to one for that function to operate (except for TxD and WR). The secondary functions are assigned to the pins of port 3 as follows: P3.0/RxD: Receiver data input (asynchronous) or data input/output (synchronous) of the serial interface P3.1/TxD: Transmitter data output (asynchronous) or clock output (synchronous) of the serial interface P3.2/INT0: External interrupt 0 input/timer 0 gate control input P3.3/INT1: External interrupt 1 input/timer 1 gate control input P3.4/T0: Timer 0 counter input P3.5/T1/SS: Timer 1 counter input SPI Slave Select P3.6/WR: External Data Memory write strobe; latches the data byte from port 0 into the external data memory P3.7/RD: External Data Memory read strobe; Enables the external data memory. It can drive CMOS inputs without external pull-ups. P4.0:4 I/O Port 4: Is an 2-bit bi-directional I/O port with internal pull-ups. Port 4 pins that have 1’s written to them are pulled high by the internal pull-ups and can be used as inputs in this state. As inputs, Port 4 pins that are being pulled low externally will be a source of current (IIL, on the datasheet) because of the internal pull-up transistor. The secondary functions are assigned to the 5 pins of port 4 as follows: P4.0: Regular Port I/O P4.1: Regular Port I/O P4.2/MISO: Master Input Slave Output of SPI controller P4.3/SCK: Serial Clock of SPI controller P4.4/MOSI: Master Ouput Slave Input of SPI controller It can drive CMOS inputs without external pull-ups. 6 AT89C51AC3 4383A–8051–10/04 AT89C51AC3 Pin Name Type Description RESET I/O Reset: A high level on this pin during two machine cycles while the oscillator is running resets the device. An internal pull-down resistor to VSS permits power-on reset using only an external capacitor to VCC. ALE O ALE: An Address Latch Enable output for latching the low byte of the address during accesses to the external memory. The ALE is activated every 1/6 oscillator periods (1/3 in X2 mode) except during an external data memory access. When instructions are executed from an internal Flash (EA = 1), ALE generation can be disabled by the software. PSEN O PSEN: The Program Store Enable output is a control signal that enables the external program memory of the bus during external fetch operations. It is activated twice each machine cycle during fetches from the external program memory. However, when executing from of the external program memory two activations of PSEN are skipped during each access to the external Data memory. The PSEN is not activated for internal fetches. EA I EA: When External Access is held at the high level, instructions are fetched from the internal Flash. When held at the low level, AT89C51AC3 fetches all instructions from the external program memory. XTAL1 I XTAL1: Input of the inverting oscillator amplifier and input of the internal clock generator circuits. To drive the device from an external clock source, XTAL1 should be driven, while XTAL2 is left unconnected. To operate above a frequency of 16 MHz, a duty cycle of 50% should be maintained. XTAL2 O XTAL2: Output from the inverting oscillator amplifier. I/O Configurations Each Port SFR operates via type-D latches, as illustrated in Figure 1 for Ports 3 and 4. A CPU "write to latch" signal initiates transfer of internal bus data into the type-D latch. A CPU "read latch" signal transfers the latched Q output onto the internal bus. Similarly, a "read pin" signal transfers the logical level of the Port pin. Some Port data instructions activate the "read latch" signal while others activate the "read pin" signal. Latch instructions are referred to as Read-Modify-Write instructions. Each I/O line may be independently programmed as input or output. Port 1, Port 3 and Port 4 Figure 1 shows the structure of Ports 1 and 3, which have internal pull-ups. An external source can pull the pin low. Each Port pin can be configured either for general-purpose I/O or for its alternate input output function. To use a pin for general-purpose output, set or clear the corresponding bit in the Px register (x = 1,3 or 4). To use a pin for general-purpose input, set the bit in the Px register. This turns off the output FET drive. To configure a pin for its alternate function, set the bit in the Px register. When the latch is set, the "alternate output function" signal controls the output level (see Figure 1). The operation of Ports 1, 3 and 4 is discussed further in the "quasi-Bidirectional Port Operation" section. 7 4383A–8051–10/04 Figure 1. Port 1, Port 3 and Port 4 Structure VCC ALTERNATE OUTPUT FUNCTION READ LATCH INTERNAL BUS READ PIN Port 0 and Port 2 P1.x P3.x P4.x D P1.X Q P3.X P4.X LATCH CL WRITE TO LATCH Note: INTERNAL PULL-UP (1) ALTERNATE INPUT FUNCTION The internal pull-up can be disabled on P1 when analog function is selected. Ports 0 and 2 are used for general-purpose I/O or as the external address/data bus. Port 0, shown in Figure 3, differs from the other Ports in not having internal pull-ups. Figure 3 shows the structure of Port 2. An external source can pull a Port 2 pin low. To use a pin for general-purpose output, set or clear the corresponding bit in the Px register (x = 0 or 2). To use a pin for general-purpose input, set the bit in the Px register to turn off the output driver FET. Figure 2. Port 0 Structure ADDRESS LOW/ CONTROL DATA VDD (2) READ LATCH P0.x (1) 1 INTERNAL BUS WRITE TO LATCH D P0.X LATCH Q 0 READ PIN Notes: 8 1. Port 0 is precluded from use as general-purpose I/O Ports when used as address/data bus drivers. 2. Port 0 internal strong pull-ups assist the logic-one output for memory bus cycles only. Except for these bus cycles, the pull-up FET is off, Port 0 outputs are open-drain. AT89C51AC3 4383A–8051–10/04 AT89C51AC3 Figure 3. Port 2 Structure ADDRESS HIGH/ CONTROL VDD INTERNAL PULL-UP (2) READ LATCH P2.x (1) 1 INTERNAL BUS WRITE TO LATCH D P2.X LATCH Q 0 READ PIN Notes: 1. Port 2 is precluded from use as general-purpose I/O Ports when as address/data bus drivers. 2. Port 2 internal strong pull-ups FET (P1 in FiGURE) assist the logic-one output for memory bus cycle. When Port 0 and Port 2 are used for an external memory cycle, an internal control signal switches the output-driver input from the latch output to the internal address/data line. Read-Modify-Write Instructions Some instructions read the latch data rather than the pin data. The latch based instructions read the data, modify the data and then rewrite the latch. These are called "ReadModify-Write" instructions. Below is a complete list of these special instructions (see Table ). When the destination operand is a Port or a Port bit, these instructions read the latch rather than the pin: Instruction Description Example ANL logical AND ANL P1, A ORL logical OR ORL P2, A XRL logical EX-OR XRL P3, A JBC jump if bit = 1 and clear bit JBC P1.1, LABEL CPL complement bit CPL P3.0 INC increment INC P2 DEC decrement DEC P2 DJNZ decrement and jump if not zero DJNZ P3, LABEL MOV Px.y, C move carry bit to bit y of Port x MOV P1.5, C CLR Px.y clear bit y of Port x CLR P2.4 SET Px.y set bit y of Port x SET P3.3 It is not obvious the last three instructions in this list are Read-Modify-Write instructions. These instructions read the port (all 8 bits), modify the specifically addressed bit and 9 4383A–8051–10/04 write the new byte back to the latch. These Read-Modify-Write instructions are directed to the latch rather than the pin in order to avoid possible misinterpretation of voltage (and therefore, logic) levels at the pin. For example, a Port bit used to drive the base of an external bipolar transistor can not rise above the transistor’s base-emitter junction voltage (a value lower than VIL). With a logic one written to the bit, attempts by the CPU to read the Port at the pin are misinterpreted as logic zero. A read of the latch rather than the pins returns the correct logic-one value. Quasi-Bidirectional Port Operation Port 1, Port 2, Port 3 and Port 4 have fixed internal pull-ups and are referred to as "quasi-bidirectional" Ports. When configured as an input, the pin impedance appears as logic one and sources current in response to an external logic zero condition. Port 0 is a "true bidirectional" pin. The pins float when configured as input. Resets write logic one to all Port latches. If logical zero is subsequently written to a Port latch, it can be returned to input conditions by a logical one written to the latch. Note: Port latch values change near the end of Read-Modify-Write instruction cycles. Output buffers (and therefore the pin state) update early in the instruction after Read-ModifyWrite instruction cycle. Logical zero-to-one transitions in Port 1, Port 2, Port 3 and Port 4 use an additional pullup (p1) to aid this logic transition (see Figure 4.). This increases switch speed. This extra pull-up sources 100 times normal internal circuit current during 2 oscillator clock periods. The internal pull-ups are field-effect transistors rather than linear resistors. Pullups consist of three p-channel FET (pFET) devices. A pFET is on when the gate senses logical zero and off when the gate senses logical one. pFET #1 is turned on for two oscillator periods immediately after a zero-to-one transition in the Port latch. A logical one at the Port pin turns on pFET #3 (a weak pull-up) through the inverter. This inverter and pFET pair form a latch to drive logical one. pFET #2 is a very weak pull-up switched on whenever the associated nFET is switched off. This is traditional CMOS switch convention. Current strengths are 1/10 that of pFET #3. Figure 4. Internal Pull-Up Configurations 2 Osc. PERIODS VCC VCC VCC p1(1) p2 p3 P1.x P2.x P3.x P4.x OUTPUT DATA n INPUT DATA READ PIN Note: 10 Port 2 p1 assists the logic-one output for memory bus cycles. AT89C51AC3 4383A–8051–10/04 AT89C51AC3 SFR Mapping The Special Function Registers (SFRs) of the AT89C51AC3 fall into the following categories: Mnemonic Add Name 7 6 5 4 3 2 1 0 ACC E0h Accumulator – – – – – – – – B F0h B Register – – – – – – – – PSW D0h Program Status Word CY AC F0 RS1 RS0 OV F1 P SP 81h Stack Pointer – – – – – – – – DPL 82h Data Pointer Low byte – – – – – – – – – – – – – – – – LSB of DPTR DPH 83h Data Pointer High byte MSB of DPTR Mnemonic Add Name 7 6 5 4 3 2 1 0 P0 80h Port 0 – – – – – – – – P1 90h Port 1 – – – – – – – – P2 A0h Port 2 – – – – – – – – P3 B0h Port 3 – – – – – – – – P4 C0h Port 4 (x5) – – – P4.4 / MOSI P4.3 / SCK P4.2 / MISO P4.1 P4.0 Mnemonic Add Name 7 6 5 4 3 2 1 0 TH0 8Ch Timer/Counter 0 High byte – – – – – – – – TL0 8Ah Timer/Counter 0 Low byte – – – – – – – – TH1 8Dh Timer/Counter 1 High byte – – – – – – – – TL1 8Bh Timer/Counter 1 Low byte – – – – – – – – TH2 CDh Timer/Counter 2 High byte – – – – – – – – TL2 CCh Timer/Counter 2 Low byte – – – – – – – – TCON 88h Timer/Counter 0 and 1 control TF1 TR1 TF0 TR0 IE1 IT1 IE0 IT0 TMOD 89h Timer/Counter 0 and 1 Modes GATE1 C/T1# M11 M01 GATE0 C/T0# M10 M00 11 4383A–8051–10/04 Mnemonic Add Name 7 6 5 4 3 2 1 0 T2CON C8h Timer/Counter 2 control TF2 EXF2 RCLK TCLK EXEN2 TR2 C/T2# CP/RL2# T2MOD C9h Timer/Counter 2 Mode – – – – – – T2OE DCEN RCAP2H Timer/Counter 2 CBh Reload/Capture High byte – – – – – – – – RCAP2L Timer/Counter 2 CAh Reload/Capture Low byte – – – – – – – – WDTRST A6h WatchDog Timer Reset – – – – – – – – WDTPRG A7h WatchDog Timer Program – – – – – S2 S1 S0 Mnemonic Add Name 7 6 5 4 3 2 1 0 FE/SM0 SM1 SM2 REN TB8 RB8 TI RI – – – – – – – – SCON 98h Serial Control SBUF 99h Serial Data Buffer SADEN B9h Slave Address Mask – – – – – – – – SADDR A9h Slave Address – – – – – – – – Mnemonic Add Name 7 6 5 4 3 2 1 0 CCON D8h PCA Timer/Counter Control CF CR – CCF4 CCF3 CCF2 CCF1 CCF0 CMOD D9h PCA Timer/Counter Mode CIDL WDTE – – – CPS1 CPS0 ECF CL E9h PCA Timer/Counter Low byte – – – – – – – – CH F9h PCA Timer/Counter High byte – – – – – – – – CCAPM0 DAh PCA Timer/Counter Mode 0 ECOM0 CAPP0 CAPN0 MAT0 TOG0 PWM0 ECCF0 CCAPM1 DBh PCA Timer/Counter Mode 1 ECOM1 CAPP1 CAPN1 MAT1 TOG1 PWM1 ECCF1 CCAPM2 DCh PCA Timer/Counter Mode 2 ECOM2 CAPP2 CAPN2 MAT2 TOG2 PWM2 ECCF2 CCAPM3 DDh PCA Timer/Counter Mode 3 ECOM3 CAPP3 CAPN3 MAT3 TOG3 PWM3 ECCF3 CCAPM4 DEh PCA Timer/Counter Mode 4 ECOM4 CAPP4 CAPN4 MAT4 TOG4 PWM4 ECCF4 – CCAP0H FAh PCA Compare Capture Module 0 H CCAP0H7 CCAP0H6 CCAP0H5 CCAP0H4 CCAP0H3 CCAP0H2 CCAP0H1 CCAP0H0 CCAP1H FBh PCA Compare Capture Module 1 H CCAP1H7 CCAP1H6 CCAP1H5 CCAP1H4 CCAP1H3 CCAP1H2 CCAP1H1 CCAP1H0 CCAP2H FCh PCA Compare Capture Module 2 H CCAP2H7 CCAP2H6 CCAP2H5 CCAP2H4 CCAP2H3 CCAP2H2 CCAP2H1 CCAP2H0 CCAP3H FDh PCA Compare Capture Module 3 H CCAP3H7 CCAP3H6 CCAP3H5 CCAP3H4 CCAP3H3 CCAP3H2 CCAP3H1 CCAP3H0 CCAP4H FEh PCA Compare Capture Module 4 H CCAP4H7 CCAP4H6 CCAP4H5 CCAP4H4 CCAP4H3 CCAP4H2 CCAP4H1 CCAP4H0 CCAP0L EAh PCA Compare Capture Module 0 L CCAP0L7 CCAP0L6 CCAP0L5 CCAP0L4 CCAP0L3 CCAP0L2 CCAP0L1 CCAP0L0 CCAP1L EBh PCA Compare Capture Module 1 L CCAP1L7 CCAP1L6 CCAP1L5 CCAP1L4 CCAP1L3 CCAP1L2 CCAP1L1 CCAP1L0 CCAP2L ECh PCA Compare Capture Module 2 L CCAP2L7 CCAP2L6 CCAP2L5 CCAP2L4 CCAP2L3 CCAP2L2 CCAP2L1 CCAP2L0 CCAP3L EDh PCA Compare Capture Module 3 L CCAP3L7 CCAP3L6 CCAP3L5 CCAP3L4 CCAP3L3 CCAP3L2 CCAP3L1 CCAP3L0 CCAP4L EEh PCA Compare Capture Module 4 L CCAP4L7 CCAP4L6 CCAP4L5 CCAP4L4 CCAP4L3 CCAP4L2 CCAP4L1 CCAP4L0 12 AT89C51AC3 4383A–8051–10/04 AT89C51AC3 Mnemonic Add Name 7 6 5 4 3 2 1 0 IEN0 A8h Interrupt Enable Control 0 EA EC ET2 ES ET1 EX1 ET0 EX0 IEN1 E8h Interrupt Enable Control 1 – – – – ESPI – EADC – IPL0 B8h Interrupt Priority Control Low 0 – PPC PT2 PS PT1 PX1 PT0 PX0 IPH0 B7h Interrupt Priority Control High 0 – PPCH PT2H PSH PT1H PX1H PT0H PX0H IPL1 F8h Interrupt Priority Control Low 1 – – – – SPIL – PADCL – IPH1 F7h Interrupt Priority Control High1 – – – – SPIH – PADCH – Mnemonic Add Name 7 6 5 4 3 2 1 0 ADCON F3h ADC Control – PSIDLE ADEN ADEOC ADSST SCH2 SCH1 SCH0 ADCF F6h ADC Configuration CH7 CH6 CH5 CH4 CH3 CH2 CH1 CH0 ADCLK F2h ADC Clock – – – PRS4 PRS3 PRS2 PRS1 PRS0 ADDH F5h ADC Data High byte ADAT9 ADAT8 ADAT7 ADAT6 ADAT5 ADAT4 ADAT3 ADAT2 ADDL F4h ADC Data Low byte – – – – – – ADAT1 ADAT0 Mnemonic Add Name 7 6 5 4 3 2 1 0 SPCON D4h SPI Control SPR2 SPEN SSDIS MSTR CPOL CPHA SPR1 SPR0 SPSCR D5h SPIF – OVR MODF SPTE UARTM SPTEIE MOFIE SPDAT D6h SPI Data – – – – – – – – 7 6 5 4 3 2 1 0 SMOD1 SMOD0 – POF GF1 GF0 PD IDL SPI Status and Control Mnemonic Add Name PCON 87h Power Control AUXR 8Eh Auxiliary Register 0 DPU VPFDP M0 XRS2 XRS1 XRS0 EXTRAM A0 AUXR1 A2h Auxiliary Register 1 – – ENBOOT – GF3 0 – DPS CKCON0 8Fh Clock Control 0 – WDX2 PCAX2 SIX2 T2X2 T1X2 T0X2 X2 CKCON1 9Fh Clock Control 1 – – – – – – – SPIX2 FCON D1h Flash Control FPL3 FPL2 FPL1 FPL0 FPS FMOD1 FMOD0 FBUSY EECON D2h EEPROM Contol EEPL3 EEPL2 EEPL1 EEPL0 – – EEE EEBUSY FSTA D3 Flash Status - - - - - - SEQERR FLOAD 13 4383A–8051–10/04 Table 1. SFR Mapping 0/8(2) 1/9 2/A 3/B 4/C 5/D 6/E F8h IPL1 xxxx x0x0 CH 0000 0000 CCAP0H 0000 0000 CCAP1H 0000 0000 CCAP2H 0000 0000 CCAP3H 0000 0000 CCAP4H 0000 0000 F0h B 0000 0000 ADCLK xxx0 0000 ADCON x000 0000 ADDL 0000 0000 ADDH 0000 0000 ADCF 0000 0000 E8h IEN1 xxxx x0x0 CCAP0L 0000 0000 CCAP1L 0000 0000 CCAP2L 0000 0000 CCAP3L 0000 0000 CCAP4L 0000 0000 E0h ACC 0000 0000 D8h CCON 0000 0000 CMOD 00xx x000 CCAPM0 x000 0000 CCAPM1 x000 0000 D0h PSW 0000 0000 FCON 0000 0000 EECON xxxx xx00 FSTA SPCON SPSCR SPDAT xxxx xx00 0001 0100 0000 0000 xxxx xxxx C8h T2CON 0000 0000 T2MOD xxxx xx00 RCAP2L 0000 0000 RCAP2H 0000 0000 TL2 0000 0000 TH2 0000 0000 C0h P4 xxx1 1111 B8h IPL0 x000 0000 B0h P3 1111 1111 A8h IEN0 0000 0000 A0h P2 1111 1111 98h SCON 0000 0000 90h P1 1111 1111 88h TCON 0000 0000 TMOD 0000 0000 TL0 0000 0000 TL1 0000 0000 80h P0 1111 1111 SP 0000 0111 DPL 0000 0000 DPH 0000 0000 0/8(2) 1/9 2/A 3/B CL 0000 0000 7/F FFh IPH1 xxxx x0x0 F7h EFh E7h CCAPM2 x000 0000 CCAPM3 x000 0000 CCAPM4 x000 0000 DFh D7h CFh C7h SADEN 0000 0000 BFh IPH0 x000 0000 SADDR 0000 0000 B7h AFh WDTRST 1111 1111 AUXR1 xxxx 00x0 SBUF 0000 0000 WDTPRG xxxx x000 A7h CKCON1 xxxx xxx0 9Fh 97h TH0 0000 0000 4/C TH1 0000 0000 5/D AUXR x001 0100 6/E CKCON0 x00 0000 8Fh PCON 00x1 0000 87h 7/F Reserved Note: 1. Do not read or write Reserved Registers 2. These registers are bit–addressable. Sixteen addresses in the SFR space are both byte–addressable and bit–addressable. The bit–addressable SFR’s are those whose address ends in 0 and 8. The bit addresses, in this area, are 0x80 through to 0xFF. 14 AT89C51AC3 4383A–8051–10/04 AT89C51AC3 Clock The AT89C51AC3 core needs only 6 clock periods per machine cycle. This feature, called”X2”, provides the following advantages: • Divides frequency crystals by 2 (cheaper crystals) while keeping the same CPU power. • Saves power consumption while keeping the same CPU power (oscillator power saving). • Saves power consumption by dividing dynamic operating frequency by 2 in operating and idle modes. • Increases CPU power by 2 while keeping the same crystal frequency. In order to keep the original C51 compatibility, a divider-by-2 is inserted between the XTAL1 signal and the main clock input of the core (phase generator). This divider may be disabled by the software. An extra feature is available to start after Reset in the X2 mode. This feature can be enabled by a bit X2B in the Hardware Security Byte. This bit is described in the section "In-System Programming". Description The X2 bit in the CKCON register (see Table 2) allows switching from 12 clock cycles per instruction to 6 clock cycles and vice versa. At reset, the standard speed is activated (STD mode). Setting this bit activates the X2 feature (X2 mode) for the CPU Clock only (see Figure 5.). The Timers 0, 1 and 2, Uart, PCA or WatchDog switch in X2 mode only if the corresponding bit is cleared in the CKCON register. The clock for the whole circuit and peripheral is first divided by two before being used by the CPU core and peripherals. This allows any cyclic ratio to be accepted on the XTAL1 input. In X2 mode, as this divider is bypassed, the signals on XTAL1 must have a cyclic ratio between 40 to 60%. Figure 5. shows the clock generation block diagram. The X2 bit is validated on the XTAL1÷2 rising edge to avoid glitches when switching from the X2 to the STD mode. Figure 6 shows the mode switching waveforms. 15 4383A–8051–10/04 Figure 5. Clock CPU Generation Diagram X2B Hardware byte PCON.0 On RESET IDL X2 CKCON.0 ÷2 XTAL1 CPU Core Clock 0 1 XTAL2 CPU CLOCK PD CPU Core Clock Symbol and ADC PCON.1 ÷2 1 FT0 Clock 0 ÷2 1 FT1 Clock 0 ÷2 1 FT2 Clock 0 ÷2 1 FUart Clock 0 ÷2 1 FPca Clock 0 ÷2 1 FWd Clock 0 ÷2 1 FSPIClock 0 X2 PERIPH CLOCK CKCON.0 SPIX2 WDX2 PCAX2 SIX2 T2X2 T1X2 T0X2 CKCON1.0 CKCON0.6 CKCON0.5 CKCON0.4 CKCON0.3 CKCON0.2 CKCON0.1 16 Peripheral Clock Symbol AT89C51AC3 4383A–8051–10/04 AT89C51AC3 Figure 6. Mode Switching Waveforms XTAL2 X2 bit CPU STD Mode Note: X2 Mode STD Mode In order to prevent any incorrect operation while operating in the X2 mode, users must be aware that all peripherals using the clock frequency as a time reference (UART, timers...) will have their time reference divided by two. For example a free running timer generating an interrupt every 20 ms will then generate an interrupt every 10 ms. A UART with a 4800 baud rate will have a 9600 baud rate. 17 4383A–8051–10/04 Registers Table 2. CKCON0 Register CKCON0 (S:8Fh) Clock Control Register 7 6 5 4 3 2 1 0 - WDX2 PCAX2 SIX2 T2X2 T1X2 T0X2 X2 Bit Number Reserved The value read from this bits is indeterminate. Do not set this bit. 7 - 6 WDX2 WatchDog clock (1) Clear to select 6 clock periods per peripheral clock cycle. Set to select 12 clock periods per peripheral clock cycle. 5 PCAX2 Programmable Counter Array clock (1) Clear to select 6 clock periods per peripheral clock cycle. Set to select 12 clock periods per peripheral clock cycle. 4 SIX2 Enhanced UART clock (MODE 0 and 2) (1) Clear to select 6 clock periods per peripheral clock cycle. Set to select 12 clock periods per peripheral clock cycle. 3 T2X2 Timer2 clock (1) Clear to select 6 clock periods per peripheral clock cycle. Set to select 12 clock periods per peripheral clock cycle. 2 T1X2 Timer1 clock (1) Clear to select 6 clock periods per peripheral clock cycle. Set to select 12 clock periods per peripheral clock cycle. 1 T0X2 Timer0 clock (1) Clear to select 6 clock periods per peripheral clock cycle. Set to select 12 clock periods per peripheral clock cycle. 0 Note: Bit Mnemonic Description X2 CPU clock Clear to select 12 clock periods per machine cycle (STD mode) for CPU and all the peripherals. Set to select 6 clock periods per machine cycle (X2 mode) and to enable the individual peripherals "X2"bits. 1. This control bit is validated when the CPU clock bit X2 is set; when X2 is low, this bit has no effect. Reset Value = x000 0000b 18 AT89C51AC3 4383A–8051–10/04 AT89C51AC3 Table 3. CKCON1 Register CKCON1 (S:9Fh) Clock Control Register 1 7 6 5 4 3 2 1 0 SPIX2 Bit Number 7-1 0 Note: Bit Mnemonic Description - SPIX2 Reserved The value read from these bits is indeterminate. Do not set these bits. SPI clock (1) Clear to select 6 clock periods per peripheral clock cycle. Set to select 12 clock periods per peripheral clock cycle. 1. This control bit is validated when the CPU clock bit X2 is set; when X2 is low, this bit has no effect. Reset Value = XXXX XXX0b 19 4383A–8051–10/04 Data Memory The AT89C51AC3 provides data memory access in two different spaces: 1. The internal space mapped in three separate segments: • the lower 128 Bytes RAM segment. • the upper 128 Bytes RAM segment. • the expanded 2048 Bytes RAM segment (ERAM). 2. The external space. A fourth internal segment is available but dedicated to Special Function Registers, SFRs, (addresses 80h to FFh) accessible by direct addressing mode. Figure 8 shows the internal and external data memory spaces organization. Figure 7. Internal Memory - RAM FFh FFh Upper 128 Bytes Internal RAM indirect addressing 80h 7Fh 00h Special Function Registers direct addressing 80h Lower 128 Bytes Internal RAM direct or indirect addressing Figure 8. Internal and External Data Memory Organization ERAM-XRAM FFFFh 64K Bytes External XRAM FFh or 7FFh 256 up to 2048 Bytes Internal ERAM EXTRAM = 0 00h 0000h Internal 20 EXTRAM = 1 External AT89C51AC3 4383A–8051–10/04 AT89C51AC3 Internal Space Lower 128 Bytes RAM The lower 128 Bytes of RAM (see Figure 8) are accessible from address 00h to 7Fh using direct or indirect addressing modes. The lowest 32 Bytes are grouped into 4 banks of 8 registers (R0 to R7). Two bits RS0 and RS1 in PSW register (see Figure 6) select which bank is in use according to Table 4. This allows more efficient use of code space, since register instructions are shorter than instructions that use direct addressing, and can be used for context switching in interrupt service routines. Table 4. Register Bank Selection RS1 RS0 Description 0 0 Register bank 0 from 00h to 07h 0 1 Register bank 0 from 08h to 0Fh 1 0 Register bank 0 from 10h to 17h 1 1 Register bank 0 from 18h to 1Fh The next 16 Bytes above the register banks form a block of bit-addressable memory space. The C51 instruction set includes a wide selection of single-bit instructions, and the 128 bits in this area can be directly addressed by these instructions. The bit addresses in this area are 00h to 7Fh. Figure 9. Lower 128 Bytes Internal RAM Organization 7Fh 30h 2Fh 20h 18h 10h 08h 00h Bit-Addressable Space (Bit Addresses 0-7Fh) 1Fh 17h 0Fh 4 Banks of 8 Registers R0-R7 07h Upper 128 Bytes RAM The upper 128 Bytes of RAM are accessible from address 80h to FFh using only indirect addressing mode. Expanded RAM The on-chip 2048 Bytes of expanded RAM (ERAM) are accessible from address 0000h to 07FFh using indirect addressing mode through MOVX instructions. In this address range, the bit EXTRAM in AUXR register is used to select the ERAM (default) or the XRAM. As shown in Figure 8 when EXTRAM = 0, the ERAM is selected and when EXTRAM = 1, the XRAM is selected. The size of ERAM can be configured by XRS2-0 bit in AUXR register (default size is 2048 Bytes). Note: Lower 128 Bytes RAM, Upper 128 Bytes RAM, and expanded RAM are made of volatile memory cells. This means that the RAM content is indeterminate after power-up and must then be initialized properly. 21 4383A–8051–10/04 External Space Memory Interface The external memory interface comprises the external bus (port 0 and port 2) as well as the bus control signals (RD#, WR#, and ALE). Figure 10 shows the structure of the external address bus. P0 carries address A7:0 while P2 carries address A15:8. Data D7:0 is multiplexed with A7:0 on P0. Table 5 describes the external memory interface signals. Figure 10. External Data Memory Interface Structure RAM PERIPHERAL AT89C51AC3 A15:8 P2 A15:8 ALE P0 AD7:0 Latch A7:0 A7:0 D7:0 RD# WR# OE WR Table 5. External Data Memory Interface Signals External Bus Cycles Signal Name Type Alternative Function A15:8 O Address Lines Upper address lines for the external bus. P2.7:0 AD7:0 I/O Address/Data Lines Multiplexed lower address lines and data for the external memory. P0.7:0 ALE O Address Latch Enable ALE signals indicates that valid address information are available on lines AD7:0. RD# O Read Read signal output to external data memory. P3.7 WR# O Write Write signal output to external memory. P3.6 Description - This section describes the bus cycles the AT89C51AC3 executes to read (see Figure 11), and write data (see Figure 12) in the external data memory. External memory cycle takes 6 CPU clock periods. This is equivalent to 12 oscillator clock period in standard mode or 6 oscillator clock periods in X2 mode. For further information on X2 mode. Slow peripherals can be accessed by stretching the read and write cycles. This is done using the M0 bit in AUXR register. Setting this bit changes the width of the RD# and WR# signals from 3 to 15 CPU clock periods. For simplicity, the accompanying figures depict the bus cycle waveforms in idealized form and do not provide precise timing information. For bus cycle timing parameters refer to the Section “AC Characteristics” of the AT89C51AC3 datasheet. 22 AT89C51AC3 4383A–8051–10/04 AT89C51AC3 Figure 11. External Data Read Waveforms CPU Clock ALE RD#1 P0 P2 Notes: DPL or Ri P2 D7:0 DPH or P22 1. RD# signal may be stretched using M0 bit in AUXR register. 2. When executing MOVX @Ri instruction, P2 outputs SFR content. Figure 12. External Data Write Waveforms CPU Clock ALE WR#1 P0 P2 Notes: DPL or Ri P2 D7:0 DPH or P22 1. WR# signal may be stretched using M0 bit in AUXR register. 2. When executing MOVX @Ri instruction, P2 outputs SFR content. 23 4383A–8051–10/04 Dual Data Pointer Description The AT89C51AC3 implements a second data pointer for speeding up code execution and reducing code size in case of intensive usage of external memory accesses. DPTR 0 and DPTR 1 are seen by the CPU as DPTR and are accessed using the SFR addresses 83h and 84h that are the DPH and DPL addresses. The DPS bit in AUXR1 register (see Figure 8) is used to select whether DPTR is the data pointer 0 or the data pointer 1 (see Figure 13). Figure 13. Dual Data Pointer Implementation DPL0 0 DPL1 1 DPL DPTR0 DPS DPTR1 DPH0 0 DPH1 1 DPTR AUXR1.0 DPH Application Software can take advantage of the additional data pointers to both increase speed and reduce code size, for example, block operations (copy, compare…) are well served by using one data pointer as a “source” pointer and the other one as a “destination” pointer. Hereafter is an example of block move implementation using the two pointers and coded in assembler. The latest C compiler takes also advantage of this feature by providing enhanced algorithm libraries. The INC instruction is a short (2 Bytes) and fast (6 machine cycle) way to manipulate the DPS bit in the AUXR1 register. However, note that the INC instruction does not directly force the DPS bit to a particular state, but simply toggles it. In simple routines, such as the block move example, only the fact that DPS is toggled in the proper sequence matters, not its actual value. In other words, the block move routine works the same whether DPS is '0' or '1' on entry. ; ASCII block move using dual data pointers ; Modifies DPTR0, DPTR1, A and PSW ; Ends when encountering NULL character ; Note: DPS exits opposite to the entry state unless an extra INC AUXR1 is added AUXR1EQU0A2h move:movDPTR,#SOURCE ; address of SOURCE incAUXR1 ; switch data pointers movDPTR,#DEST ; address of DEST mv_loop:incAUXR1; switch data pointers movxA,@DPTR; get a byte from SOURCE incDPTR; increment SOURCE address incAUXR1; switch data pointers movx@DPTR,A; write the byte to DEST incDPTR; increment DEST address jnzmv_loop; check for NULL terminator end_move: 24 AT89C51AC3 4383A–8051–10/04 AT89C51AC3 Registers Table 6. PSW Register PSW (S:8Eh) Program Status Word Register 7 6 5 4 3 2 1 0 CY AC F0 RS1 RS0 OV F1 P Bit Number Bit Mnemonic Description 7 CY Carry Flag Carry out from bit 1 of ALU operands. 6 AC Auxiliary Carry Flag Carry out from bit 1 of addition operands. 5 F0 User Definable Flag 0. 4-3 RS1:0 2 OV Overflow Flag Overflow set by arithmetic operations. 1 F1 User Definable Flag 1 0 P Parity Bit Set when ACC contains an odd number of 1’s. Cleared when ACC contains an even number of 1’s. Register Bank Select Bits Refer to Table 4 for bits description. Reset Value = 0000 0000b Table 7. AUXR Register AUXR (S:8Eh) Auxiliary Register 7 6 5 4 3 2 1 0 - - M0 XRS2 XRS1 XRS0 EXTRAM A0 Bit Number 7-6 5 Bit Mnemonic Description - M0 Reserved The value read from these bits are indeterminate. Do not set this bit. Stretch MOVX control: the RD/ and the WR/ pulse length is increased according to the value of M0. M0 Pulse length in clock period 0 6 1 30 25 4383A–8051–10/04 Bit Number 4-2 1 0 Bit Mnemonic Description XRS1-0 EXTRAM A0 ERAM size: Accessible size of the ERAM XRS 2:0 ERAM size 000 256 Bytes 001 512 Bytes 010 768 Bytes 011 1024 Bytes 100 1792 Bytes 101 2048 Bytes (default configuration after reset) 110 Reserved 111 Reserved Internal/External RAM (00h - FFh) access using MOVX @ Ri/@ DPTR 0 - Internal ERAM access using MOVX @ Ri/@ DPTR. 1 - External data memory access. Disable/Enable ALE) 0 - ALE is emitted at a constant rate of 1/6 the oscillator frequency (or 1/3 if X2 mode is used) 1 - ALE is active only during a MOVX or MOVC instruction. Reset Value = X001 0100b Not bit addressable Table 8. AUXR1 Register AUXR1 (S:A2h) Auxiliary Control Register 1 7 6 5 4 3 2 1 0 - - ENBOOT - GF3 0 - DPS Bit Number Bit Mnemonic Description Reserved The value read from these bits is indeterminate. Do not set these bits. 7-6 - 5 ENBOOT 4 - 3 GF3 2 0 Always Zero This bit is stuck to logic 0 to allow INC AUXR1 instruction without affecting GF3 flag. 1 - Reserved for Data Pointer Extension. 0 DPS Enable Boot Flash Set this bit for map the boot Flash between F800h -FFFFh Clear this bit for disable boot Flash. Reserved The value read from this bit is indeterminate. Do not set this bit. General-purpose Flag 3 Data Pointer Select Bit Set to select second dual data pointer: DPTR1. Clear to select first dual data pointer: DPTR0. Reset Value = XXXX 00X0b 26 AT89C51AC3 4383A–8051–10/04 AT89C51AC3 Power Monitor The POR/PFD function monitors the internal power-supply of the CPU core memories and the peripherals, and if needed, suspends their activity when the internal power supply falls below a safety threshold. This is achieved by applying an internal reset to them. By generating the Reset the Power Monitor insures a correct start up when AT89C51CC03 is powered up. Description In order to startup and maintain the microcontroller in correct operating mode, VCC has to be stabilized in the VCC operating range and the oscillator has to be stabilized with a nominal amplitude compatible with logic level VIH/VIL. These parameters are controlled during the three phases: power-up, normal operation and power going down. See Figure 14. Figure 14. Power Monitor Block Diagram VCC CPU core Power On Reset Power Fail Detect Voltage Regulator Regulated Supply Memories Peripherals XTAL1 (1) Internal Reset RST pin PCA Watchdog Note: Hardware Watchdog 1. Once XTAL1 high and low levels reach above and below VIH/VIL a 1024 clock period delay will extend the reset coming from the Power Fail Detect. If the power falls below the Power Fail Detect thresthold level, the reset will be applied immediately. The Voltage regulator generates a regulated internal supply for the CPU core the memories and the peripherals. Spikes on the external Vcc are smoothed by the voltage regulator. The Power fail detect monitor the supply generated by the voltage regulator and generate a reset if this supply falls below a safety threshold as illustrated in the Figure 15. 27 4383A–8051–10/04 Figure 15. Power Fail Detect Vcc t Reset Vcc When the power is applied, the Power Monitor immediately asserts a reset. Once the internal supply after the voltage regulator reach a safety level, the power monitor then looks at the XTAL clock input. The internal reset will remain asserted until the Xtal1 levels are above and below VIH and VIL. Further more. An internal counter will count 1024 clock periods before the reset is de-asserted. If the internal power supply falls below a safety level, a reset is immediately asserted. . 28 AT89C51AC3 4383A–8051–10/04 AT89C51AC3 Reset Introduction The reset sources are : Power Management, Hardware Watchdog, PCA Watchdog and Reset input. Figure 16. Reset Schematic Power Monitor Hardware Watchdog Internal Reset PCA Watchdog RST Reset Input The Reset input can be used to force a reset pulse longer than the internal reset controlled by the Power Monitor. RST input has a pull-down resistor allowing power-on reset by simply connecting an external capacitor to VCC as shown in Figure 17. Resistor value and input characteristics are discussed in the Section “DC Characteristics” of the AT89C51AC3 datasheet. The status of the Port pins during reset is detailed in Table 9. Figure 17. Reset Circuitry and Power-On Reset VDD To internal reset RST R RST + RST VSS a. RST input circuitry b. Power-on Reset 29 4383A–8051–10/04 Reset Output As detailed in Section “Watchdog Timer”, page 79, the WDT generates a 96-clock period pulse on the RST pin. In order to properly propagate this pulse to the rest of the application in case of external capacitor or power-supply supervisor circuit, a 1 kΩ resistor must be added as shown Figure 18. Figure 18. Recommended Reset Output Schematic VDD + RST VDD 1K AT89C51AC3 RST VSS 30 To other on-board circuitry AT89C51AC3 4383A–8051–10/04 AT89C51AC3 Power Management Introduction Two power reduction modes are implemented in the AT89C51AC3. The Idle mode and the Power-Down mode. These modes are detailed in the following sections. In addition to these power reduction modes, the clocks of the core and peripherals can be dynamically divided by 2 using the X2 mode detailed in Section “Clock”, page 15. Idle Mode Idle mode is a power reduction mode that reduces the power consumption. In this mode, program execution halts. Idle mode freezes the clock to the CPU at known states while the peripherals continue to be clocked. The CPU status before entering Idle mode is preserved, i.e., the program counter and program status word register retain their data for the duration of Idle mode. The contents of the SFRs and RAM are also retained. The status of the Port pins during Idle mode is detailed in Table 9. Entering Idle Mode To enter Idle mode, set the IDL bit in PCON register (see Table 10). The AT89C51AC3 enters Idle mode upon execution of the instruction that sets IDL bit. The instruction that sets IDL bit is the last instruction executed. Note: Exiting Idle Mode If IDL bit and PD bit are set simultaneously, the AT89C51AC3 enters Power-Down mode. Then it does not go in Idle mode when exiting Power-Down mode. There are two ways to exit Idle mode: 1. Generate an enabled interrupt. – Hardware clears IDL bit in PCON register which restores the clock to the CPU. Execution resumes with the interrupt service routine. Upon completion of the interrupt service routine, program execution resumes with the instruction immediately following the instruction that activated Idle mode. The general purpose flags (GF1 and GF0 in PCON register) may be used to indicate whether an interrupt occurred during normal operation or during Idle mode. When Idle mode is exited by an interrupt, the interrupt service routine may examine GF1 and GF0. 2. Generate a reset. – Note: Power-Down Mode A logic high on the RST pin clears IDL bit in PCON register directly and asynchronously. This restores the clock to the CPU. Program execution momentarily resumes with the instruction immediately following the instruction that activated the Idle mode and may continue for a number of clock cycles before the internal reset algorithm takes control. Reset initializes the AT89C51AC3 and vectors the CPU to address C:0000h. During the time that execution resumes, the internal RAM cannot be accessed; however, it is possible for the Port pins to be accessed. To avoid unexpected outputs at the Port pins, the instruction immediately following the instruction that activated Idle mode should not write to a Port pin or to the external RAM. The Power-Down mode places the AT89C51AC3 in a very low power state. PowerDown mode stops the oscillator, freezes all clock at known states. The CPU status prior to entering Power-Down mode is preserved, i.e., the program counter, program status word register retain their data for the duration of Power-Down mode. In addition, the SFR and RAM contents are preserved. The status of the Port pins during Power-Down mode is detailed in Table 9. Note: VCC may be reduced to as low as VRET during Power-Down mode to further reduce power dissipation. Take care, however, that VDD is not reduced until Power-Down mode is invoked. 31 4383A–8051–10/04 Entering Power-Down Mode To enter Power-Down mode, set PD bit in PCON register. The AT89C51AC3 enters the Power-Down mode upon execution of the instruction that sets PD bit. The instruction that sets PD bit is the last instruction executed. Exiting Power-Down Mode Note: If VCC was reduced during the Power-Down mode, do not exit Power-Down mode until VCC is restored to the normal operating level. There are two ways to exit the Power-Down mode: 1. Generate an enabled external interrupt. – The AT89C51AC3 provides capability to exit from Power-Down using INT0#, INT1#. Hardware clears PD bit in PCON register which starts the oscillator and restores the clocks to the CPU and peripherals. Using INTx# input, execution resumes when the input is released (see Figure 19). Execution resumes with the interrupt service routine. Upon completion of the interrupt service routine, program execution resumes with the instruction immediately following the instruction that activated Power-Down mode. Note: The external interrupt used to exit Power-Down mode must be configured as level sensitive (INT0# and INT1#) and must be assigned the highest priority. In addition, the duration of the interrupt must be long enough to allow the oscillator to stabilize. The execution will only resume when the interrupt is deasserted. Note: Exit from power-down by external interrupt does not affect the SFRs nor the internal RAM content. Figure 19. Power-Down Exit Waveform Using INT1:0# INT1:0# OSC Active phase Power-down phase Oscillator restart phase Active phase 2. Generate a reset. – 32 A logic high on the RST pin clears PD bit in PCON register directly and asynchronously. This starts the oscillator and restores the clock to the CPU and peripherals. Program execution momentarily resumes with the instruction immediately following the instruction that activated Power-Down mode and may continue for a number of clock cycles before the internal reset algorithm takes control. Reset initializes the AT89C51AC3 and vectors the CPU to address 0000h. Note: During the time that execution resumes, the internal RAM cannot be accessed; however, it is possible for the Port pins to be accessed. To avoid unexpected outputs at the Port pins, the instruction immediately following the instruction that activated the Power-Down mode should not write to a Port pin or to the external RAM. Note: Exit from power-down by reset redefines all the SFRs, but does not affect the internal RAM content. AT89C51AC3 4383A–8051–10/04 AT89C51AC3 Table 9. Pin Conditions in Special Operating Modes Mode Port 0 Port 1 Port 2 Port 3 Port 4 ALE PSEN# Reset Floating High High High High High High Idle (internal code) Data Data Data Data Data High High Idle (external code) Floating Data Data Data Data High High PowerDown(inter nal code) Data Data Data Data Data Low Low PowerDown (external code) Floating Data Data Data Data Low Low 33 4383A–8051–10/04 Registers Table 10. PCON Register PCON (S87:h) Power configuration Register 7 6 5 4 3 2 1 0 - - - - GF1 GF0 PD IDL Bit Number Bit Mnemonic Description Reserved The value read from these bits is indeterminate. Do not set these bits. 7-4 - 3 GF1 General Purpose flag 1 One use is to indicate whether an interrupt occurred during normal operation or during Idle mode. 2 GF0 General Purpose flag 0 One use is to indicate whether an interrupt occurred during normal operation or during Idle mode. PD Power-Down Mode bit Cleared by hardware when an interrupt or reset occurs. Set to activate the Power-Down mode. If IDL and PD are both set, PD takes precedence. IDL Idle Mode bit Cleared by hardware when an interrupt or reset occurs. Set to activate the Idle mode. If IDL and PD are both set, PD takes precedence. 1 0 Reset Value= XXXX 0000b 34 AT89C51AC3 4383A–8051–10/04 AT89C51AC3 EEPROM Data Memory The 2-Kbyte on-chip EEPROM memory block is located at addresses 0000h to 07FFh of the XRAM/ERAM memory space and is selected by setting control bits in the EECON register. A read in the EEPROM memory is done with a MOVX instruction. A physical write in the EEPROM memory is done in two steps: write data in the column latches and transfer of all data latches into an EEPROM memory row (programming). The number of data written on the page may vary from 1 up to 128 Bytes (the page size). When programming, only the data written in the column latch is programmed and a ninth bit is used to obtain this feature. This provides the capability to program the whole memory by Bytes, by page or by a number of Bytes in a page. Indeed, each ninth bit is set when the writing the corresponding byte in a row and all these ninth bits are reset after the writing of the complete EEPROM row. Write Data in the Column Latches Data is written by byte to the column latches as for an external RAM memory. Out of the 11 address bits of the data pointer, the 4 MSBs are used for page selection (row) and 7 are used for byte selection. Between two EEPROM programming sessions, all the addresses in the column latches must stay on the same page, meaning that the 4 MSB must no be changed. The following procedure is used to write to the column latches: • Save and disable interrupt. • Set bit EEE of EECON register • Load DPTR with the address to write • Store A register with the data to be written • Execute a MOVX @DPTR, A • If needed loop the three last instructions until the end of a 128 Bytes page • Restore interrupt. Note: Programming The EEPROM programming consists of the following actions: • writing one or more Bytes of one page in the column latches. Normally, all Bytes must belong to the same page; if not, the first page address will be latched and the others discarded. • launching programming by writing the control sequence (50h followed by A0h) to the EECON register. • EEBUSY flag in EECON is then set by hardware to indicate that programming is in progress and that the EEPROM segment is not available for reading. • The end of programming is indicated by a hardware clear of the EEBUSY flag. Note: Read Data The last page address used when loading the column latch is the one used to select the page programming address. The sequence 5xh and Axh must be executed without instructions between then otherwise the programming is aborted. The following procedure is used to read the data stored in the EEPROM memory: • Save and disable interrupt • Set bit EEE of EECON register • Load DPTR with the address to read • Execute a MOVX A, @DPTR • Restore interrupt 35 4383A–8051–10/04 Examples ;*F*************************************************************************;* NAME: api_rd_eeprom_byte ;* DPTR contain address to read. ;* Acc contain the reading value ;* NOTE: before execute this function, be sure the EEPROM is not BUSY ;*************************************************************************** api_rd_eeprom_byte: MOV EECON, #02h; map EEPROM in XRAM space MOVX A, @DPTR MOV EECON, #00h; unmap EEPROM ret ;*F************************************************************************* ;* NAME: api_ld_eeprom_cl ;* DPTR contain address to load ;* Acc contain value to load ;* NOTE: in this example we load only 1 byte, but it is possible upto ;* 128 Bytes. ;* before execute this function, be sure the EEPROM is not BUSY ;*************************************************************************** api_ld_eeprom_cl: MOV EECON, #02h ; map EEPROM in XRAM space MOVX @DPTR, A MOVEECON, #00h; unmap EEPROM ret ;*F************************************************************************* ;* NAME: api_wr_eeprom ;* NOTE: before execute this function, be sure the EEPROM is not BUSY ;*************************************************************************** api_wr_eeprom: MOV EECON, #050h MOV EECON, #0A0h ret 36 AT89C51AC3 4383A–8051–10/04 AT89C51AC3 Registers Table 11. EECON Register EECON (S:0D2h) EEPROM Control Register 7 6 5 4 3 2 1 0 EEPL3 EEPL2 EEPL1 EEPL0 - - EEE EEBUSY Bit Number Bit Mnemonic 7-4 EEPL3-0 Programming Launch command bits Write 5Xh followed by AXh to EEPL to launch the programming. 3 - Reserved The value read from this bit is indeterminate. Do not set this bit. 2 - Reserved The value read from this bit is indeterminate. Do not set this bit. 1 EEE 0 EEBUSY Description Enable EEPROM Space bit Set to map the EEPROM space during MOVX instructions (Write in the column latches) Clear to map the XRAM space during MOVX. Programming Busy flag Set by hardware when programming is in progress. Cleared by hardware when programming is done. Can not be set or cleared by software. Reset Value = XXXX XX00b Not bit addressable 37 4383A–8051–10/04 Program/Code Memory The AT89C51AC3 implement 64K Bytes of on-chip program/code memory. Figure 20 shows the partitioning of internal and external program/code memory spaces depending on the product. The Flash memory increases EPROM and ROM functionality by in-circuit electrical erasure and programming. Thanks to the internal charge pump, the high voltage needed for programming or erasing Flash cells is generated on-chip using the standard VDD voltage. Thus, the Flash Memory can be programmed using only one voltage and allows InSystem Programming commonly known as ISP. Hardware programming mode is also available using specific programming tool. Figure 20. Program/Code Memory Organization FFFFh FFFFh 64K Bytes external memory 64K Bytes internal Flash EA = 0 EA = 1 0000h 38 0000h AT89C51AC3 4383A–8051–10/04 AT89C51AC3 External Code Memory Access Memory Interface The external memory interface comprises the external bus (port 0 and port 2) as well as the bus control signals (PSEN#, and ALE). Figure 21 shows the structure of the external address bus. P0 carries address A7:0 while P2 carries address A15:8. Data D7:0 is multiplexed with A7:0 on P0. Table 21 describes the external memory interface signals. Figure 21. External Code Memory Interface Structure Flash EPROM AT89C51AC3 A15:8 P2 A15:8 ALE P0 AD7:0 Latch A7:0 A7:0 D7:0 PSEN# OE Table 12. External Code Memory Interface Signals External Bus Cycles Signal Name Type A15:8 O Address Lines Upper address lines for the external bus. P2.7:0 AD7:0 I/O Address/Data Lines Multiplexed lower address lines and data for the external memory. P0.7:0 ALE O Address Latch Enable ALE signals indicates that valid address information are available on lines AD7:0. - PSEN# O Program Store Enable Output This signal is active low during external code fetch or external code read (MOVC instruction). - Description Alternate Function This section describes the bus cycles the AT89C51AC3 executes to fetch code (see Figure 22) in the external program/code memory. External memory cycle takes 6 CPU clock periods. This is equivalent to 12 oscillator clock period in standard mode or 6 oscillator clock periods in X2 mode. For further information on X2 mode see section “Clock “. For simplicity, the accompanying figure depicts the bus cycle waveforms in idealized form and do not provide precise timing information. For bus cycling parameters refer to the ‘AC-DC parameters’ section. 39 4383A–8051–10/04 Figure 22. External Code Fetch Waveforms CPU Clock ALE PSEN# P0 D7:0 PCL P2 PCH Flash Memory Architecture D7:0 PCL D7:0 PCH PCH AT89C51AC3 features two on-chip Flash memories: • Flash memory FM0: containing 64K Bytes of program memory (user space) organized into 128 byte pages, • Flash memory FM1: 2K Bytes for boot loader and Application Programming Interfaces (API). The FM0 can be program by both parallel programming and Serial In-System Programming (ISP) whereas FM1 supports only parallel programming by programmers. The ISP mode is detailed in the "In-System Programming" section. All Read/Write access operations on Flash Memory by user application are managed by a set of API described in the "In-System Programming" section. The bit ENBOOT in AUXR1 register is used to map FM1 from F800h to FFFFh. Figure 23 and Figure 24 show the Flash memory configuration with ENBOOT=1 and ENBOOT=0. Figure 23. Flash Memory Architecture with ENBOOT=1 (boot mode) Hardware Security (1 byte) Extra Row (128 Bytes) Column Latches (128 Bytes) FFFFh 64K Bytes 2K Bytes Flash memory boot space FM1 F800h FM0 FFFFh F800h FM1 mapped between FFFFh and F800h when bit ENBOOT is set in AUXR1 register 0000h Memory space not accessible 40 AT89C51AC3 4383A–8051–10/04 AT89C51AC3 Figure 24. Flash Memory Architecture with ENBOOT=0 (user modemode) Hardware Security (1 byte) Extra Row (128 Bytes) Column Latches (128 Bytes) FFFFh 64K Bytes 2K Bytes Flash memory boot space FM1 F800h FM0 FFFFh F800h FM1 mapped between FFFFh and F800h when bit ENBOOT is set in AUXR1 register 0000h Memory space not accessible 41 4383A–8051–10/04 FM0 Memory Architecture The Flash memory is made up of 4 blocks (see Figure 23): • The memory array (user space) 64K Bytes • The Extra Row • The Hardware security bits • The column latch registers User Space This space is composed of a 64K Bytes Flash memory organized in 512 pages of 128 Bytes. It contains the user’s application code. Extra Row (XRow) This row is a part of FM0 and has a size of 128 Bytes. The extra row may contain information for boot loader usage. Hardware security Byte (HSB) The Hardware security Byte space is a part of FM0 and has a size of 1 byte. The 4 MSB can be read/written by software (from FM0 and , the 4 LSB can only be read by software and written by hardware in parallel mode. H Hardware Security Byte (HSB) 7 6 5 4 3 2 1 0 X2 BLJB - - - LB2 LB1 LB0 Bit Number Bit Mnemonic 7 X2 Description X2 Mode Programmed (=’0’) to force X2 mode (6 clocks per instruction) after reset Unprogrammed to force X1 mode, Standard Mode, afetr reset (Default) Boot Loader Jump Bit When unprogrammed (=’1’), at the next reset : -ENBOOT=0 (see code space memory configuration) 6 BLJB -Start address is 0000h (PC=0000h) When programmed (=’0’)at the nex reset: -ENBOOT=1 (see code space memory configuration) -Start address is F800h (PC=F800h) 5 - Reserved 4 - Reserved 3 - Reserved 2-0 LB2-0 General Memory Lock Bits (only programmable by programmer tools) Section “Flash Protection from Parallel Programming”, page 51 Column Latches The column latches, also part of FM0, have a size of full page (128 Bytes). The column latches are the entrance buffers of the three previous memory locations (user array, XROW and Hardware security byte). The column latches are write only and can be accessed only from FM1 (boot mode) and from external memory Cross Flash Memory Access Description The FM0 memory can be program only from FM1. Programming FM0 from FM0 or from external memory is impossible. The FM1 memory can be program only by parallel programming. The Table show all software Flash access allowed. 42 AT89C51AC3 4383A–8051–10/04 AT89C51AC3 Code executing from Cross Flash Memory Access FM0 (user Flash) FM1 (boot Flash) Action FM0 (user Flash) FM1 (boot Flash) Read ok - Load column latch ok - Write - - Read ok ok Load column latch ok - Write ok - Read (a) - External memory Load column latch - - EA = 0 Write - - (a) Depend upon general lock bit configuration. 43 4383A–8051–10/04 Overview of FM0 Operations Flash Registers (SFR) The CPU interfaces to the flash memory through the FCON register, AUXR1 register and FSTA register. These registers are used to map the column latches, HSB, extra row and EEDATA in the working data or code space. FCON Register Table 13. FCON Register FCON Register (S:D1h) Flash Control Register 7 6 5 4 3 2 1 0 FPL3 FPL2 FPL1 FPL0 FPS FMOD1 FMOD0 FBUSY Bit Number 7-4 Bit Mnemonic Description FPL3:0 Programming Launch Command Bits Write 5Xh followed by AXh to launch the programming according to FMOD1:0. (see Table 16.) Flash Map Program Space When this bit is set: 3 FPS The MOVX @DPTR, A instruction writes in the columns latches space When this bit is cleared: The MOVX @DPTR, A instruction writes in the regular XDATA memory space 2-1 0 FMOD1:0 FBUSY Flash Mode See Table 16. Flash Busy Set by hardware when programming is in progress. Clear by hardware when programming is done. Can not be changed by software. Reset Value= 0000 0000b 44 AT89C51AC3 4383A–8051–10/04 AT89C51AC3 FSTA Register Table 14. FSTA Register FSTA Register (S:D3h) Flash Status Register 7 6 Bit Number 5 4 3 2 1 0 SEQERR FLOAD Bit Mnemonic Description 7-2 unusesd 1 SEQERR Flash activation sequence error Set by hardware when the flash activation sequence(MOV FCON 5X and MOV FCON AX )is not correct (See Error Repport Section) Clear by software or clear by hardware if the last activation sequence was correct (previous error are canceled) 0 FLOAD Flash Colums latch loaded Set by hardware when the first data is loaded in the column latches. Clear by hardware when the activation sequence suceed (flash write sucess, or reset column latch success) Reset Value= 0000 0000b Mapping of the Memory Space By default, the user space is accessed by MOVC A, @DPTR instruction for read only. The column latches space is made accessible by setting the FPS bit in FCON register. Writing is possible from 0000h to FFFFh, address bits 6 to 0 are used to select an address within a page while bits 15 to 7 are used to select the programming address of the page. Setting FPS bit takes precedence on the EXTRAM bit in AUXR register. The other memory spaces (user, extra row, hardware security) are made accessible in the code segment by programming bits FMOD0 and FMOD1 in FCON register in accordance with Table 15. A MOVC instruction is then used for reading these spaces. Table 15. FM0 Blocks Select Bits Notes: Launching Programming FMOD1 FMOD0 FM0 Adressable space 0 0 User (0000h-FFFFh) 0 1 Extra Row(FF80h-FFFFh) 1 0 Hardware Security Byte (0000h) 1 1 Column latches reset (note1) 1. The column latches reset is a new option introduced in the AT89C51AC3, and is not available in T89C51CC01/2 FPL3:0 bits in FCON register are used to secure the launch of programming. A specific sequence must be written in these bits to unlock the write protection and to launch the programming. This sequence is 5xh followed by Axh. Table 16 summarizes the memory spaces to program according to FMOD1:0 bits. 45 4383A–8051–10/04 Table 16. Programming Spaces Write to FCON FPL3:0 FPS FMOD1 FMOD0 Operation 5 X 0 0 No action A X 0 0 Write the column latches in user space 5 X 0 1 No action A X 0 1 Write the column latches in extra row space User Extra Row Hardware Security Byte 5 X 1 0 No action A X 1 0 Write the fuse bits space Reset 5 X 1 1 No action Columns Latches A X 1 1 Reset the column latches Notes: Status of the Flash Memory 1. The sequence 5xh and Axh must be executing without instructions between them otherwise the programming is not executed (see Flash Status Register) 2. The sequence 5xh and Axh must be executed with the same FMOD0 FMOD1 configuration. 3. Interrupts that may occur during programming time must be disabled to avoid any spurious exit of the programming mode. The bit FBUSY in FCON register is used to indicate the status of programming. FBUSY is set when programming is in progress. The flash programming process is launched the second machine cycle following the sequence 5xh and Axh in FCON. Thus the FBUSY flag should be read by sofware not during the insctruction after the 5xh, Axh sequence but the the second instruction after the 5xh, Axh sequence in FCON (See next example). FBUSY is cleared when the programming is completed. ;*F************************************************************************* ;* NAME: launch_prog ;;*************************************************************************** launch_prog: MOV FCON, #050h MOV FCON #0A0h ; Flash Write Sequence NOP ;Required time before reading busy flag wait_busy: MOV A,FCON JB ACC.0,wait_busy RET Selecting FM1 The bit ENBOOT in AUXR1 register is used to map FM1 from F800h to FFFFh. Loading the Column Latches Any number of data from 1-byte to 128 Bytes can be loaded in the column latches. This provides the capability to program the whole memory by byte, by page or by any number of Bytes in a page. Data written in the column latches do not have to be in consecutive 46 AT89C51AC3 4383A–8051–10/04 AT89C51AC3 order. The page address of the last address loaded in the column latches will be used for the whole page. When programming is launched, an automatic erase of the locations loaded in the column latches is first performed, then programming is effectively done. Thus no page or block erase is needed and only the loaded data are programmed in the corresponding page Notes: 1. : If no bytes are written in the column latches the SEQERR bit in the FSTA register will be set. 2. When a flash write sequence is in progress (FBUSY is set) a write sequence to the column latches will be ignored and the content of the column latches at the time of the launch write sequence will be preserved. 3. MOVX @DPTR, A instruction must be used to load the column latches. Never use MOVX @Ri, A instructions. 4. When a programming sequence is launched, Flash bytes corresponding to activated bytes in the column latches are first erased then the bytes in the column latches are copied into the Flash bytes. Flash bytes corresponding to bytes in the column latches not activated (not loaded during the load column latches sequence) will not be erased and written. The following procedure is used to load the column latches and is summarized in Figure 25: • Save and Disable interrupt and map the column latch space by setting FPS bit. • Load the DPTR with the address to load. • Load Accumulator register with the data to load. • Execute the MOVX @DPTR, A instruction. • If needed loop the three last instructions until the page is completely loaded. • unmap the column latch. • Restore Interrupt 47 4383A–8051–10/04 Figure 25. Column Latches Loading Procedure Column Latches Loading Save and Disable IT EA = 0 Column Latches Mapping FCON = 08h (FPS=1) Data Load DPTR = Address ACC = Data Exec: MOVX @DPTR, A Last Byte to load? Data memory Mapping FCON = 00h (FPS = 0) Restore IT Note: The last page address used when loading the column latch is the one used to select the page programming address. Programming the Flash Spaces User The following procedure is used to program the User space and is summarized in Figure 26: Extra Row 48 • Load up to one page of data in the column latches from address 0000h to FFFFh. • Save and Disable the interrupts. • Launch the programming by writing the data sequence 50h followed by A0h in FCON register (only from FM1). The end of the programming indicated by the FBUSY flag cleared. • Restore the interrupts. The following procedure is used to program the Extra Row space and is summarized in Figure 26: • Load data in the column latches from address FF80h to FFFFh. • Save and Disable the interrupts. • Launch the programming by writing the data sequence 52h followed by A2h in FCON register (only from FM1). The end of the programming indicated by the FBUSY flag cleared. • Restore the interrupts. AT89C51AC3 4383A–8051–10/04 AT89C51AC3 Figure 26. Flash and Extra Row Programming Procedure Flash Spaces Programming Column Latches Loading see Figure 25 Save and Disable IT EA = 0 Launch Programming FCON = 5xh FCON = Axh FBusy Cleared? Clear Mode FCON = 00h End Programming Restore IT Hardware Security Byte The following procedure is used to program the Hardware Security Byte space and is summarized in Figure 27: • Set FPS and map Hardware byte (FCON = 0x0C) • Save and disable the interrupts. • Load DPTR at address 0000h. • Load Accumulator register with the data to load. • Execute the MOVX @DPTR, A instruction. • Launch the programming by writing the data sequence 54h followed by A4h in FCON register (only from FM1). The end of the programming indicated by the FBusy flag cleared. • Restore the interrupts. 49 4383A–8051–10/04 Figure 27. Hardware Programming Procedure Flash Spaces Programming Save and Disable IT EA = 0 Save and Disable IT EA = 0 FCON = 0Ch Launch Programming FCON = 54h FCON = A4h Data Load DPTR = 00h ACC = Data Exec: MOVX @DPTR, A FBusy Cleared? End Loading Restore IT Clear Mode FCON = 00h End Programming RestoreIT Reset the Column Latches An automatic reset of the column latches is performed after a successful Flash write sequence. User can also reset the column latches manually, for instance to reload the column latches before writing the Flash. The following procedure is summarized below. • Save and disable the interrupts. • Launch the reset by writing the data sequence 56h followed by A6h in FCON register (only from FM1). • Restore the interrupts. Error Reports Flash Programming Sequence Errors When a wrong sequence is detected, the SEQERR bit in FSTA register is set. Possible wrong sequence are : • MOV FCON, 5xh instruction not immediately followed by a MOV FCON, Ax instruction. • A write Flash sequence is launched while no data were loaded in the column latches The SEQERR bit can be cleared • By software • By hardware when a correct programming sequence is completed When multiple pages are written into the Flash, the user should check FSTA for errors after each write page sequences, not only at the end of the multiple write pages. 50 AT89C51AC3 4383A–8051–10/04 AT89C51AC3 Power Down Request Before entering in Power Down (Set bit PD in PCON register) the user should check that no write sequence is in progress (check BUSY=0), then check that the column latches are reset (FLOAD=0 in FSTA register. Launch a reset column latches to clear FLOAD if necessary. Reading the Flash Spaces User The following procedure is used to read the User space: • Read one byte in Accumulator by executing MOVC A,@A+DPTR with A+DPTR=read@. Note: Extra Row Hardware Security Byte FCON is supposed to be reset when not needed. The following procedure is used to read the Extra Row space and is summarized in Figure 28: • Map the Extra Row space by writing 02h in FCON register. • Read one byte in Accumulator by executing MOVC A,@A+DPTR with A = 0 and DPTR = FF80h to FFFFh. • Clear FCON to unmap the Extra Row. The following procedure is used to read the Hardware Security space and is summarized in Figure 28: • Map the Hardware Security space by writing 04h in FCON register. • Read the byte in Accumulator by executing MOVC A,@A+DPTR with A = 0 and DPTR = 0000h. Figure 28. Clear FCON to unmap the Hardware Security Byte.Reading Procedure Flash Spaces Reading Flash Spaces Mapping FCON= 00000xx0b Data Read DPTR= Address ACC= 0 Exec: MOVC A, @A+DPTR Clear Mode FCON = 00h Flash Protection from Parallel Programming The three lock bits in Hardware Security Byte (see "In-System Programming" section) are programmed according to Table 17 provide different level of protection for the onchip code and data located in FM0 and FM1. The only way to write this bits are the parallel mode. They are set by default to level 4 51 4383A–8051–10/04 Table 17. Program Lock Bit Program Lock Bits Security level LB0 LB1 LB2 1 U U U No program lock features enabled. U MOVC instruction executed from external program memory are disabled from fetching code bytes from internal memory, EA is sampled and latched on reset, and further parallel programming of the Flash is disabled. 2 P U Protection Description ISP and software programming with API are still allowed. Writing EEprom Data from external parallel programmer is disabled but still allowed from internal code execution. Same as 2, also verify through parallel programming interface is disabled. 3 U P U 4 U U P Writing And Reading EEPROM Data from external parallel programmer is disabled but still allowed from internal code execution.. Same as 3, also external execution is disabled Program Lock bits U: unprogrammed P: programmed WARNING: Security level 2 and 3 should only be programmed after Flash and Core verification. 52 AT89C51AC3 4383A–8051–10/04 AT89C51AC3 Operation Cross Memory Access Space addressable in read and write are: • RAM • ERAM (Expanded RAM access by movx) • XRAM (eXternal RAM) • EEPROM DATA • FM0 ( user flash ) • Hardware byte • XROW • Boot Flash • Flash Column latch The table below provide the different kind of memory which can be accessed from different code location. Table 18. Cross Memory Access XRAM Action RAM ERAM Hardware Boot FLASH FM0 E² Data Byte XROW Read OK OK OK OK - Write - OK (RWW) OK (RWW) OK (RWW) OK (RWW) OK OK -OK - boot FLASH Read FM0 External memory OK (confidential) Write - OK (idle) OK(RWW) - -OK Read - - OK - - Write - - OK(RWW) - - EA = 0 or Code Roll Over 53 4383A–8051–10/04 Sharing Instructions Table 19. Instructions shared XRAM Action RAM ERAM EEPROM DATA Boot FLASH FM0 Hardware Byte XROW Read MOV MOVX MOVX MOVC MOVC MOVC MOVC Write MOV MOVX MOVX - by cl by cl by cl Note: by cl : using Column Latch Table 20. Read MOVX A, @DPTR Flash EEE bit in FPS in XRAM EECON Register FCON Register ENBOOT EA ERAM 0 0 X X winner 0 1 X X winner 1 0 X X 1 1 X X EEPROM DATA Column Latch winner winner Table 21. Write MOVX @DPTR,A Flash EEE bit in FPS bit in XRAM EECON Register FCON Register ENBOOT EA ERAM 0 0 X X winner 0 1 X EEPROM Data 1 0 1 0 X 1 1 X winner winner 1 54 Latch winner X 0 Column winner winner AT89C51AC3 4383A–8051–10/04 AT89C51AC3 Table 22. Read MOVC A, @DPTR FCON Register Code Execution FMOD1 0 FMOD0 0 FPS ENBOOT DPTR 0 0000h to FFFFh winner 0000h to F7FF winner X FM1 FM0 XROW Hardware External Byte Code 1 F800h to FFFFh Do not use this configuration 0000 to 007Fh 0 1 X X 1 0 X X X 0 000h to FFFFh winner 0000h to F7FF winner From FM0 1 1 X winner See (1) winner 1 F800h to FFFFh Do not use this configuration 0000h to F7FF winner 1 F800h to FFFFh 0 0 0 0 X 1 X 0 X 1 0000h to 007h winner NA winner 1 From FM1 (ENBOOT =1 0 1 X 0 See NA winner (2) NA 1 1 0 X winner X 0 NA 1 1 1 X winner 000h to FFFFh 0 NA External code : EA=0 or Code Roll Over X 0 X X X winner 1. For DPTR higher than 007Fh only lowest 7 bits are decoded, thus the behavior is the same as for addresses from 0000h to 007Fh 2. For DPTR higher than 007Fh only lowest 7 bits are decoded, thus the behavior is the same as for addresses from 0000h to 007Fh 55 4383A–8051–10/04 In-System Programming (ISP) With the implementation of the User Space (FM0) and the Boot Space (FM1) in Flash technology the AT89C51AC3 allows the system engineer the development of applications with a very high level of flexibility. This flexibility is based on the possibility to alter the customer program at any stages of a product’s life: • Before assembly the 1st personalization of the product by programming in the FM0 and if needed also a customized Boot loader in the FM1. Atmel provide also a standard UART Boot loader by default. • After assembling on the PCB in its final embedded position by serial mode via the UART. This In-System Programming (ISP) allows code modification over the total lifetime of the product. Besides the default Boot loader Atmel provide to the customer also all the needed Application-Programming-Interfaces (API) which are needed for the ISP. The API are located also in the Boot memory. This allow the customer to have a full use of the 64-Kbyte user memory. Flash Programming and Erasure There are three methods of programming the Flash memory: • The Atmel bootloader located in FM1 is activated by the application. Low level API routines (located in FM1)will be used to program FM0. The interface used for serial downloading to FM0 is the UART. API can be called also by the user’s bootloader located in FM0 at [SBV]00h. • A further method exists in activating the Atmel boot loader by hardware activation. • The FM0 can be programmed also by the parallel mode using a programmer. Figure 29. Flash Memory Mapping FFFFh FFFFh Custom Boot Loader F800h 2K Bytes IAP bootloader FM1 [SBV]00h 64K Bytes Flash memory FM1 mapped between F800h and FFFFh when API called FM0 0000h Boot Process Software Boot Process Example 56 Many algorithms can be used for the software boot process. Before describing them, The description of the different flags and Bytes is given below: AT89C51AC3 4383A–8051–10/04 AT89C51AC3 Boot Loader Jump Bit (BLJB): - This bit indicates if on RESET the user wants to jump to this application at address @0000h on FM0 or execute the boot loader at address @F800h on FM1. - BLJB = 0 on parts delivered with bootloader programmed. - To read or modify this bit, the APIs are used. Boot Vector Address (SBV): - This byte contains the MSB of the user boot loader address in FM0. - The default value of SBV is FFh (no user boot loader in FM0). - To read or modify this byte, the APIs are used. Extra Byte (EB) and Boot Status Byte (BSB): - These Bytes are reserved for customer use. - To read or modify these Bytes, the APIs are used. Hardware Boot Process At the falling edge of RESET, the bit ENBOOT in AUXR1 register is initialized with the value of Boot Loader Jump Bit (BLJB). Further at the falling edge of RESET if the following conditions (called Hardware condition) are detected: • PSEN low, • EA high, • ALE high (or not connected). – After Hardware Condition the FCON register is initialized with the value 00h and the PC is initialized with F800h (FM1). The Hardware condition makes the bootloader to be executed, whatever BLJB value is. If no hardware condition is detected, the FCON register is initialized with the value F0h. Check of the BLJB value. • If bit BLJB = 1: User application in FM0 will be started at @0000h (standard reset). • If bit BLJB = 0: Boot loader will be started at @F800h in FM1. Note: 1. As PSEN is an output port in normal operating mode (running user applications or bootloader applications) after reset it is recommended to release PSEN after the falling edge of Reset is signaled. The hardware conditions are sampled at reset signal Falling Edge, thus they can be released at any time when reset input is low. 2. To ensure correct microcontroller startup, the PSEN pin should not be tied to ground during power-on. 57 4383A–8051–10/04 Figure 30. Hardware Boot Process Algorithm bit ENBOOT in AUXR1 register is initialized with BLJB. RESET Hardware Hardware condition? No ENBOOT = 0 PC = 0000h No ENBOOT = 1 PC = F800h FCON = 00h Yes FCON = F0h BLJB = = 0 ? Yes Software ENBOOT = 1 PC = F800h Application in FM0 Application Programming Interface Boot Loader in FM1 Several Application Program Interface (API) calls are available for use by an application program to permit selective erasing and programming of Flash pages. All calls are made by functions. All these APIs are describe in an documentation: "In-System Programing: Flash Library for AT89C51AC3" available on the Atmel web site. XROW Bytes 58 Table 23. XROW Mapping Description Default Value Address Copy of the Manufacturer Code 58h 30h Copy of the Device ID#1: Family code D7h 31h Copy of the Device ID#2: Memories size and type FFh 60h Copy of the Device ID#3: Name and Revision FEh 61h AT89C51AC3 4383A–8051–10/04 AT89C51AC3 Hardware Security Byte Table 24. Hardware Security Byte 7 6 5 4 3 2 1 0 X2B BLJB - - - LB2 LB1 LB0 Bit Number Bit Mnemonic Description 7 X2B X2 Bit Set this bit to start in standard mode Clear this bit to start in X2 mode. 6 BLJB Boot Loader JumpBit - 1: To start the user’s application on next RESET (@0000h) located in FM0, - 0: To start the boot loader(@F800h) located in FM1. 5-3 - 2-0 LB2:0 Reserved The value read from these bits are indeterminate. Lock Bits Default value after erasing chip: FFh Notes: 1. Only the 4 MSB bits can be accessed by software. 2. The 4 LSB bits can only be accessed by parallel mode. 59 4383A–8051–10/04 Serial I/O Port The AT89C51AC3 I/O serial port is compatible with the I/O serial port in the 80C52. It provides both synchronous and asynchronous communication modes. It operates as a Universal Asynchronous Receiver and Transmitter (UART) in three full-duplex modes (Modes 1, 2 and 3). Asynchronous transmission and reception can occur simultaneously and at different baud rates Serial I/O port includes the following enhancements: • Framing error detection • Automatic address recognition Figure 31. Serial I/O Port Block Diagram IB Bus Write SBUF Read SBUF SBUF Receiver SBUF Transmitter TXD Load SBUF Mode 0 Transmit Receive Shift register RXD Serial Port Interrupt Request RI TI SCON reg Framing Error Detection Framing bit error detection is provided for the three asynchronous modes. To enable the framing bit error detection feature, set SMOD0 bit in PCON register. Figure 32. Framing Error Block Diagram SM0/FE SM1 SM2 REN TB8 RB8 TI RI Set FE bit if stop bit is 0 (framing error) SM0 to UART mode control SMOD SMOD0 - POF GF1 GF0 PD IDL To UART framing error control When this feature is enabled, the receiver checks each incoming data frame for a valid stop bit. An invalid stop bit may result from noise on the serial lines or from simultaneous transmission by two CPUs. If a valid stop bit is not found, the Framing Error bit (FE) in SCON register bit is set. The software may examine the FE bit after each reception to check for data errors. Once set, only software or a reset clears the FE bit. Subsequently received frames with valid stop bits cannot clear the FE bit. When the FE feature is enabled, RI rises on the stop bit instead of the last data bit (See Figure 33. and Figure 34.). 60 AT89C51AC3 4383A–8051–10/04 AT89C51AC3 Figure 33. UART Timing in Mode 1 RXD D0 D1 D2 Start bit D3 D4 D5 D6 D7 Stop bit Data byte RI SMOD0=X FE SMOD0=1 Figure 34. UART Timing in Modes 2 and 3 RXD D0 Start bit D1 D2 D3 D4 Data byte D5 D6 D7 D8 Ninth Stop bit bit RI SMOD0=0 RI SMOD0=1 FE SMOD0=1 Automatic Address Recognition The automatic address recognition feature is enabled when the multiprocessor communication feature is enabled (SM2 bit in SCON register is set). Implemented in the hardware, automatic address recognition enhances the multiprocessor communication feature by allowing the serial port to examine the address of each incoming command frame. Only when the serial port recognizes its own address will the receiver set the RI bit in the SCON register to generate an interrupt. This ensures that the CPU is not interrupted by command frames addressed to other devices. If necessary, you can enable the automatic address recognition feature in mode 1. In this configuration, the stop bit takes the place of the ninth data bit. Bit RI is set only when the received command frame address matches the device’s address and is terminated by a valid stop bit. To support automatic address recognition, a device is identified by a given address and a broadcast address. Note: The multiprocessor communication and automatic address recognition features cannot be enabled in mode 0 (i.e. setting SM2 bit in SCON register in mode 0 has no effect). 61 4383A–8051–10/04 Given Address Each device has an individual address that is specified in the SADDR register; the SADEN register is a mask byte that contains don’t-care bits (defined by zeros) to form the device’s given address. The don’t-care bits provide the flexibility to address one or more slaves at a time. The following example illustrates how a given address is formed. To address a device by its individual address, the SADEN mask byte must be 1111 1111b. For example: SADDR0101 0110b SADEN1111 1100b Given0101 01XXb Here is an example of how to use given addresses to address different slaves: Slave A:SADDR1111 0001b SADEN1111 1010b Given1111 0X0Xb Slave B:SADDR1111 0011b SADEN1111 1001b Given1111 0XX1b Slave C:SADDR1111 0011b SADEN1111 1101b Given1111 00X1b The SADEN byte is selected so that each slave may be addressed separately. For slave A, bit 0 (the LSB) is a don’t-care bit; for slaves B and C, bit 0 is a 1. To communicate with slave A only, the master must send an address where bit 0 is clear (e.g. 1111 0000b). For slave A, bit 1 is a 0; for slaves B and C, bit 1 is a don’t care bit. To communicate with slaves A and B, but not slave C, the master must send an address with bits 0 and 1 both set (e.g. 1111 0011b). To communicate with slaves A, B and C, the master must send an address with bit 0 set, bit 1 clear, and bit 2 clear (e.g. 1111 0001b). Broadcast Address A broadcast address is formed from the logical OR of the SADDR and SADEN registers with zeros defined as don’t-care bits, e.g.: SADDR0101 0110b SADEN1111 1100b SADDR OR SADEN1111 111Xb The use of don’t-care bits provides flexibility in defining the broadcast address, however in most applications, a broadcast address is FFh. The following is an example of using broadcast addresses: Slave A:SADDR1111 0001b SADEN1111 1010b Given1111 1X11b, Slave B:SADDR1111 0011b SADEN1111 1001b Given1111 1X11B, Slave C:SADDR=1111 0010b SADEN1111 1101b Given1111 1111b 62 AT89C51AC3 4383A–8051–10/04 AT89C51AC3 For slaves A and B, bit 2 is a don’t care bit; for slave C, bit 2 is set. To communicate with all of the slaves, the master must send an address FFh. To communicate with slaves A and B, but not slave C, the master can send and address FBh. Registers Table 25. SCON Register SCON (S:98h) Serial Control Register 7 6 5 4 3 2 1 0 FE/SM0 SM1 SM2 REN TB8 RB8 TI RI Bit Number 7 Bit Mnemonic Description FE Framing Error bit (SMOD0=1) Clear to reset the error state, not cleared by a valid stop bit. Set by hardware when an invalid stop bit is detected. SM0 Serial port Mode bit 0 (SMOD0=0) Refer to SM1 for serial port mode selection. 6 SM1 Serial port Mode bit 1 Mode SM0 SM1 0 0 Shift Register 0 1 8-bit UART 1 0 9-bit UART 1 1 9-bit UART 5 SM2 Serial port Mode 2 bit/Multiprocessor Communication Enable bit Clear to disable multiprocessor communication feature. Set to enable multiprocessor communication feature in mode 2 and 3. 4 REN Reception Enable bit Clear to disable serial reception. Set to enable serial reception. 3 TB8 Transmitter Bit 8/Ninth bit to transmit in modes 2 and 3 Clear to transmit a logic 0 in the 9th bit. Set to transmit a logic 1 in the 9th bit. 2 RB8 Receiver Bit 8/Ninth bit received in modes 2 and 3 Cleared by hardware if 9th bit received is a logic 0. Set by hardware if 9th bit received is a logic 1. 1 TI Transmit Interrupt flag Clear to acknowledge interrupt. Set by hardware at the end of the 8th bit time in mode 0 or at the beginning of the stop bit in the other modes. 0 RI Receive Interrupt flag Clear to acknowledge interrupt. Set by hardware at the end of the 8th bit time in mode 0, see Figure 33. and Figure 34. in the other modes. Baud Rate FXTAL/12 (or FXTAL /6 in mode X2) Variable FXTAL/64 or FXTAL/32 Variable Reset Value = 0000 0000b Bit addressable 63 4383A–8051–10/04 Table 26. SADEN Register SADEN (S:B9h) Slave Address Mask Register 7 6 5 4 3 2 1 0 – – – – – – – – Bit Number Bit Mnemonic Description 7-0 Mask Data for Slave Individual Address Reset Value = 0000 0000b Not bit addressable Table 27. SADDR Register SADDR (S:A9h) Slave Address Register 7 6 5 4 3 2 1 0 – – – – – – – – Bit Number Bit Mnemonic Description 7-0 Slave Individual Address Reset Value = 0000 0000b Not bit addressable Table 28. SBUF Register SBUF (S:99h) Serial Data Buffer 7 6 5 4 3 2 1 0 – – – – – – – – Bit Number 7-0 Bit Mnemonic Description Data sent/received by Serial I/O Port Reset Value = 0000 0000b Not bit addressable 64 AT89C51AC3 4383A–8051–10/04 AT89C51AC3 Table 29. PCON Register PCON (S:87h) Power Control Register 7 6 5 4 3 2 1 0 SMOD1 SMOD0 – POF GF1 GF0 PD IDL Bit Number Bit Mnemonic Description 7 SMOD1 Serial port Mode bit 1 Set to select double baud rate in mode 1, 2 or 3. 6 SMOD0 Serial port Mode bit 0 Clear to select SM0 bit in SCON register. Set to select FE bit in SCON register. 5 - Reserved The value read from this bit is indeterminate. Do not set this bit. 4 POF Power-Off Flag Clear to recognize next reset type. Set by hardware when VCC rises from 0 to its nominal voltage. Can also be set by software. 3 GF1 General-purpose Flag Cleared by user for general-purpose usage. Set by user for general-purpose usage. 2 GF0 General-purpose Flag Cleared by user for general-purpose usage. Set by user for general-purpose usage. 1 PD Power-Down mode bit Cleared by hardware when reset occurs. Set to enter power-down mode. 0 IDL Idle mode bit Clear by hardware when interrupt or reset occurs. Set to enter idle mode. Reset Value = 00X1 0000b Not bit addressable 65 4383A–8051–10/04 Timers/Counters The AT89C51AC3 implements two general-purpose, 16-bit Timers/Counters. Such are identified as Timer 0 and Timer 1, and can be independently configured to operate in a variety of modes as a Timer or an event Counter. When operating as a Timer, the Timer/Counter runs for a programmed length of time, then issues an interrupt request. When operating as a Counter, the Timer/Counter counts negative transitions on an external pin. After a preset number of counts, the Counter issues an interrupt request. The various operating modes of each Timer/Counter are described in the following sections. Timer/Counter Operations A basic operation is Timer registers THx and TLx (x = 0, 1) connected in cascade to form a 16-bit Timer. Setting the run control bit (TRx) in TCON register (see Figure 30) turns the Timer on by allowing the selected input to increment TLx. When TLx overflows it increments THx; when THx overflows it sets the Timer overflow flag (TFx) in TCON register. Setting the TRx does not clear the THx and TLx Timer registers. Timer registers can be accessed to obtain the current count or to enter preset values. They can be read at any time but TRx bit must be cleared to preset their values, otherwise the behavior of the Timer/Counter is unpredictable. The C/Tx# control bit selects Timer operation or Counter operation by selecting the divided-down peripheral clock or external pin Tx as the source for the counted signal. TRx bit must be cleared when changing the mode of operation, otherwise the behavior of the Timer/Counter is unpredictable. For Timer operation (C/Tx# = 0), the Timer register counts the divided-down peripheral clock. The Timer register is incremented once every peripheral cycle (6 peripheral clock periods). The Timer clock rate is FPER/6, i.e. FOSC/12 in standard mode or FOSC/6 in X2 mode. For Counter operation (C/Tx# = 1), the Timer register counts the negative transitions on the Tx external input pin. The external input is sampled every peripheral cycles. When the sample is high in one cycle and low in the next one, the Counter is incremented. Since it takes 2 cycles (12 peripheral clock periods) to recognize a negative transition, the maximum count rate is FPER/12, i.e. FOSC/24 in standard mode or FOSC/12 in X2 mode. There are no restrictions on the duty cycle of the external input signal, but to ensure that a given level is sampled at least once before it changes, it should be held for at least one full peripheral cycle. Timer 0 Timer 0 functions as either a Timer or event Counter in four modes of operation. Figure 35 to Figure 38 show the logical configuration of each mode. Timer 0 is controlled by the four lower bits of TMOD register (see Figure 31) and bits 0, 1, 4 and 5 of TCON register (see Figure 30). TMOD register selects the method of Timer gating (GATE0), Timer or Counter operation (T/C0#) and mode of operation (M10 and M00). TCON register provides Timer 0 control functions: overflow flag (TF0), run control bit (TR0), interrupt flag (IE0) and interrupt type control bit (IT0). For normal Timer operation (GATE0 = 0), setting TR0 allows TL0 to be incremented by the selected input. Setting GATE0 and TR0 allows external pin INT0# to control Timer operation. Timer 0 overflow (count rolls over from all 1s to all 0s) sets TF0 flag generating an interrupt request. It is important to stop Timer/Counter before changing mode. 66 AT89C51AC3 4383A–8051–10/04 AT89C51AC3 Mode 0 (13-bit Timer) Mode 0 configures Timer 0 as an 13-bit Timer which is set up as an 8-bit Timer (TH0 register) with a modulo 32 prescaler implemented with the lower five bits of TL0 register (see Figure 35). The upper three bits of TL0 register are indeterminate and should be ignored. Prescaler overflow increments TH0 register. Figure 35. Timer/Counter x (x = 0 or 1) in Mode 0 See the “Clock” section FTx CLOCK ÷6 0 THx (8 bits) 1 TLx (5 bits) Overflow TFx TCON reg Tx Timer x Interrupt Request C/Tx# TMOD reg INTx# GATEx TRx TMOD reg Mode 1 (16-bit Timer) TCON reg Mode 1 configures Timer 0 as a 16-bit Timer with TH0 and TL0 registers connected in cascade (see Figure 36). The selected input increments TL0 register. Figure 36. Timer/Counter x (x = 0 or 1) in Mode 1 See the “Clock” section FTx CLOCK ÷6 0 THx (8 bits) 1 Tx TLx (8 bits) Overflow TFx TCON reg Timer x Interrupt Request C/Tx# TMOD reg INTx# GATEx TMOD reg TRx TCON reg 67 4383A–8051–10/04 Mode 2 (8-bit Timer with AutoReload) Mode 2 configures Timer 0 as an 8-bit Timer (TL0 register) that automatically reloads from TH0 register (see Figure 37). TL0 overflow sets TF0 flag in TCON register and reloads TL0 with the contents of TH0, which is preset by software. When the interrupt request is serviced, hardware clears TF0. The reload leaves TH0 unchanged. The next reload value may be changed at any time by writing it to TH0 register. Figure 37. Timer/Counter x (x = 0 or 1) in Mode 2 See the “Clock” section FTx CLOCK ÷6 0 TLx (8 bits) 1 Overflow TFx TCON reg Tx Timer x Interrupt Request C/Tx# TMOD reg INTx# GATEx THx (8 bits) TRx TMOD reg TCON reg Mode 3 (Two 8-bit Timers) Mode 3 configures Timer 0 such that registers TL0 and TH0 operate as separate 8-bit Timers (see Figure 38). This mode is provided for applications requiring an additional 8bit Timer or Counter. TL0 uses the Timer 0 control bits C/T0# and GATE0 in TMOD register, and TR0 and TF0 in TCON register in the normal manner. TH0 is locked into a Timer function (counting FPER /6) and takes over use of the Timer 1 interrupt (TF1) and run control (TR1) bits. Thus, operation of Timer 1 is restricted when Timer 0 is in mode 3. Figure 38. Timer/Counter 0 in Mode 3: Two 8-bit Counters FTx CLOCK ÷6 0 1 TL0 (8 bits) Overflow TH0 (8 bits) Overflow TF0 TCON.5 T0 Timer 0 Interrupt Request C/T0# TMOD.2 INT0# GATE0 TMOD.3 FTx CLOCK ÷6 See the “Clock” section 68 TR0 TCON.4 TF1 TCON.7 Timer 1 Interrupt Request TR1 TCON.6 AT89C51AC3 4383A–8051–10/04 AT89C51AC3 Timer 1 Timer 1 is identical to Timer 0 excepted for Mode 3 which is a hold-count mode. The following comments help to understand the differences: • Timer 1 functions as either a Timer or event Counter in three modes of operation. Figure 35 to Figure 37 show the logical configuration for modes 0, 1, and 2. Timer 1’s mode 3 is a hold-count mode. • Timer 1 is controlled by the four high-order bits of TMOD register (see Figure 31) and bits 2, 3, 6 and 7 of TCON register (see Figure 30). TMOD register selects the method of Timer gating (GATE1), Timer or Counter operation (C/T1#) and mode of operation (M11 and M01). TCON register provides Timer 1 control functions: overflow flag (TF1), run control bit (TR1), interrupt flag (IE1) and interrupt type control bit (IT1). • Timer 1 can serve as the Baud Rate Generator for the Serial Port. Mode 2 is best suited for this purpose. • For normal Timer operation (GATE1 = 0), setting TR1 allows TL1 to be incremented by the selected input. Setting GATE1 and TR1 allows external pin INT1# to control Timer operation. • Timer 1 overflow (count rolls over from all 1s to all 0s) sets the TF1 flag generating an interrupt request. • When Timer 0 is in mode 3, it uses Timer 1’s overflow flag (TF1) and run control bit (TR1). For this situation, use Timer 1 only for applications that do not require an interrupt (such as a Baud Rate Generator for the Serial Port) and switch Timer 1 in and out of mode 3 to turn it off and on. • It is important to stop Timer/Counter before changing mode. Mode 0 (13-bit Timer) Mode 0 configures Timer 1 as a 13-bit Timer, which is set up as an 8-bit Timer (TH1 register) with a modulo-32 prescaler implemented with the lower 5 bits of the TL1 register (see Figure 35). The upper 3 bits of TL1 register are ignored. Prescaler overflow increments TH1 register. Mode 1 (16-bit Timer) Mode 1 configures Timer 1 as a 16-bit Timer with TH1 and TL1 registers connected in cascade (see Figure 36). The selected input increments TL1 register. Mode 2 (8-bit Timer with AutoReload) Mode 2 configures Timer 1 as an 8-bit Timer (TL1 register) with automatic reload from TH1 register on overflow (see Figure 37). TL1 overflow sets TF1 flag in TCON register and reloads TL1 with the contents of TH1, which is preset by software. The reload leaves TH1 unchanged. Mode 3 (Halt) Placing Timer 1 in mode 3 causes it to halt and hold its count. This can be used to halt Timer 1 when TR1 run control bit is not available i.e. when Timer 0 is in mode 3. 69 4383A–8051–10/04 Interrupt Each Timer handles one interrupt source that is the timer overflow flag TF0 or TF1. This flag is set every time an overflow occurs. Flags are cleared when vectoring to the Timer interrupt routine. Interrupts are enabled by setting ETx bit in IEN0 register. This assumes interrupts are globally enabled by setting EA bit in IEN0 register. Figure 39. Timer Interrupt System Timer 0 Interrupt Request TF0 TCON.5 ET0 IEN0.1 Timer 1 Interrupt Request TF1 TCON.7 ET1 IEN0.3 Registers Table 30. TCON Register TCON (S:88h) Timer/Counter Control Register 7 6 5 4 3 2 1 0 TF1 TR1 TF0 TR0 IE1 IT1 IE0 IT0 Bit Number Bit Mnemonic Description 7 TF1 Timer 1 Overflow Flag Cleared by hardware when processor vectors to interrupt routine. Set by hardware on Timer/Counter overflow, when Timer 1 register overflows. 6 TR1 Timer 1 Run Control Bit Clear to turn off Timer/Counter 1. Set to turn on Timer/Counter 1. 5 TF0 Timer 0 Overflow Flag Cleared by hardware when processor vectors to interrupt routine. Set by hardware on Timer/Counter overflow, when Timer 0 register overflows. 4 TR0 Timer 0 Run Control Bit Clear to turn off Timer/Counter 0. Set to turn on Timer/Counter 0. 3 IE1 Interrupt 1 Edge Flag Cleared by hardware when interrupt is processed if edge-triggered (see IT1). Set by hardware when external interrupt is detected on INT1# pin. 2 IT1 Interrupt 1 Type Control Bit Clear to select low level active (level triggered) for external interrupt 1 (INT1#). Set to select falling edge active (edge triggered) for external interrupt 1. 1 IE0 Interrupt 0 Edge Flag Cleared by hardware when interrupt is processed if edge-triggered (see IT0). Set by hardware when external interrupt is detected on INT0# pin. 0 IT0 Interrupt 0 Type Control Bit Clear to select low level active (level triggered) for external interrupt 0 (INT0#). Set to select falling edge active (edge triggered) for external interrupt 0. Reset Value = 0000 0000b 70 AT89C51AC3 4383A–8051–10/04 AT89C51AC3 Table 31. TMOD Register TMOD (S:89h) Timer/Counter Mode Control Register 7 6 5 4 3 2 1 0 GATE1 C/T1# M11 M01 GATE0 C/T0# M10 M00 Bit Number Bit Mnemonic Description 7 GATE1 Timer 1 Gating Control Bit Clear to enable Timer 1 whenever TR1 bit is set. Set to enable Timer 1 only while INT1# pin is high and TR1 bit is set. 6 C/T1# Timer 1 Counter/Timer Select Bit Clear for Timer operation: Timer 1 counts the divided-down system clock. Set for Counter operation: Timer 1 counts negative transitions on external pin T1. 5 M11 4 M01 3 GATE0 Timer 0 Gating Control Bit Clear to enable Timer 0 whenever TR0 bit is set. Set to enable Timer/Counter 0 only while INT0# pin is high and TR0 bit is set. 2 C/T0# Timer 0 Counter/Timer Select Bit Clear for Timer operation: Timer 0 counts the divided-down system clock. Set for Counter operation: Timer 0 counts negative transitions on external pin T0. 1 M10 0 M00 Timer 1 Mode Select Bits Operating mode M11 M01 0 0 Mode 0: 8-bit Timer/Counter (TH1) with 5-bit prescaler (TL1). 0 1 Mode 1: 16-bit Timer/Counter. 1 0 Mode 2: 8-bit auto-reload Timer/Counter (TL1) (1) 1 1 Mode 3: Timer 1 halted. Retains count Timer 0 Mode Select Bit M10 M00 Operating mode 0 0 Mode 0: 8-bit Timer/Counter (TH0) with 5-bit prescaler (TL0). 0 1 Mode 1: 16-bit Timer/Counter. 1 0 Mode 2: 8-bit auto-reload Timer/Counter (TL0) (2) 1 1 Mode 3: TL0 is an 8-bit Timer/Counter TH0 is an 8-bit Timer using Timer 1’s TR0 and TF0 bits. 1. Reloaded from TH1 at overflow. 2. Reloaded from TH0 at overflow. Reset Value = 0000 0000b 71 4383A–8051–10/04 Table 32. TH0 Register TH0 (S:8Ch) Timer 0 High Byte Register 7 6 5 4 3 2 1 0 – – – – – – – – Bit Number Bit Mnemonic Description 7:0 High Byte of Timer 0. Reset Value = 0000 0000b Table 33. TL0 Register TL0 (S:8Ah) Timer 0 Low Byte Register 7 6 5 4 3 2 1 0 – – – – – – – – Bit Number Bit Mnemonic Description 7:0 Low Byte of Timer 0. Reset Value = 0000 0000b Table 34. TH1 Register TH1 (S:8Dh) Timer 1 High Byte Register 7 6 5 4 3 2 1 0 – – – – – – – – Bit Number 7:0 Bit Mnemonic Description High Byte of Timer 1. Reset Value = 0000 0000b 72 AT89C51AC3 4383A–8051–10/04 AT89C51AC3 Table 35. TL1 Register TL1 (S:8Bh) Timer 1 Low Byte Register 7 6 5 4 3 2 1 0 – – – – – – – – Bit Number 7:0 Bit Mnemonic Description Low Byte of Timer 1. Reset Value = 0000 0000b 73 4383A–8051–10/04 Timer 2 The AT89C51AC3 timer 2 is compatible with timer 2 in the 80C52. It is a 16-bit timer/counter: the count is maintained by two eight-bit timer registers, TH2 and TL2 that are cascade- connected. It is controlled by T2CON register (See Table ) and T2MOD register (See Table 38). Timer 2 operation is similar to Timer 0 and Timer 1. C/T2 selects FT2 clock/6 (timer operation) or external pin T2 (counter operation) as timer clock. Setting TR2 allows TL2 to be incremented by the selected input. Timer 2 includes the following enhancements: Auto-Reload Mode • Auto-reload mode (up or down counter) • Programmable clock-output The auto-reload mode configures timer 2 as a 16-bit timer or event counter with automatic reload. This feature is controlled by the DCEN bit in T2MOD register (See Table 38). Setting the DCEN bit enables timer 2 to count up or down as shown in Figure 40. In this mode the T2EX pin controls the counting direction. When T2EX is high, timer 2 counts up. Timer overflow occurs at FFFFh which sets the TF2 flag and generates an interrupt request. The overflow also causes the 16-bit value in RCAP2H and RCAP2L registers to be loaded into the timer registers TH2 and TL2. When T2EX is low, timer 2 counts down. Timer underflow occurs when the count in the timer registers TH2 and TL2 equals the value stored in RCAP2H and RCAP2L registers. The underflow sets TF2 flag and reloads FFFFh into the timer registers. The EXF2 bit toggles when timer 2 overflow or underflow, depending on the direction of the count. EXF2 does not generate an interrupt. This bit can be used to provide 17-bit resolution. Figure 40. Auto-Reload Mode Up/Down Counter see section “Clock” FT2 CLOCK :6 0 1 TR2 T2CON.2 CT/2 T2CON.1 T2 (DOWN COUNTING RELOAD VALUE) FFh (8-bit) FFh (8-bit) T2EX: 1=UP 2=DOWN TOGGLE T2CONreg EXF2 TL2 (8-bit) TH2 (8-bit) TF2 TIMER 2 INTERRUPT T2CONreg RCAP2L (8-bit) RCAP2H (8-bit) (UP COUNTING RELOAD VALUE) 74 AT89C51AC3 4383A–8051–10/04 AT89C51AC3 Programmable ClockOutput In clock-out mode, timer 2 operates as a 50%-duty-cycle, programmable clock generator (See Figure 41). The input clock increments TL2 at frequency F OSC/2. The timer repeatedly counts to overflow from a loaded value. At overflow, the contents of RCAP2H and RCAP2L registers are loaded into TH2 and TL2. In this mode, timer 2 overflows do not generate interrupts. The formula gives the clock-out frequency depending on the system oscillator frequency and the value in the RCAP2H and RCAP2L registers: FT2clock Clock – OutFrequency = ----------------------------------------------------------------------------------------4 × ( 65536 – RCAP2H ⁄ RCAP2L ) For a 16 MHz system clock in x1 mode, timer 2 has a programmable frequency range of 61 Hz (FOSC/216) to 4 MHz (FOSC/4). The generated clock signal is brought out to T2 pin (P1.0). Timer 2 is programmed for the clock-out mode as follows: • Set T2OE bit in T2MOD register. • Clear C/T2 bit in T2CON register. • Determine the 16-bit reload value from the formula and enter it in RCAP2H/RCAP2L registers. • Enter a 16-bit initial value in timer registers TH2/TL2. It can be the same as the reload value or different depending on the application. • To start the timer, set TR2 run control bit in T2CON register. It is possible to use timer 2 as a baud rate generator and a clock generator simultaneously. For this configuration, the baud rates and clock frequencies are not independent since both functions use the values in the RCAP2H and RCAP2L registers. Figure 41. Clock-Out Mode TL2 (8-bit) FT2 CLOCK TH2 (8-bit) OVERFLOW TR2 T2CON.2 RCAP2L RCAP2H (8-bit) (8-bit) Toggle T2 Q Q D T2OE T2MOD reg EXF2 T2EX EXEN2 T2CON reg TIMER 2 INTERRUPT T2CON reg 75 4383A–8051–10/04 Registers Table 36. T2CON Register T2CON (S:C8h) Timer 2 Control Register 7 6 5 4 3 2 1 0 TF2 EXF2 RCLK TCLK EXEN2 TR2 C/T2# CP/RL2# Bit Number 7 Bit Mnemonic Description TF2 Timer 2 Overflow Flag TF2 is not set if RCLK=1 or TCLK = 1. Must be cleared by software. Set by hardware on timer 2 overflow. 6 EXF2 Timer 2 External Flag Set when a capture or a reload is caused by a negative transition on T2EX pin if EXEN2=1. Set to cause the CPU to vector to timer 2 interrupt routine when timer 2 interrupt is enabled. Must be cleared by software. 5 RCLK Receive Clock bit Clear to use timer 1 overflow as receive clock for serial port in mode 1 or 3. Set to use timer 2 overflow as receive clock for serial port in mode 1 or 3. 4 TCLK Transmit Clock bit Clear to use timer 1 overflow as transmit clock for serial port in mode 1 or 3. Set to use timer 2 overflow as transmit clock for serial port in mode 1 or 3. 3 EXEN2 2 TR2 1 C/T2# 0 CP/RL2# Timer 2 External Enable bit Clear to ignore events on T2EX pin for timer 2 operation. Set to cause a capture or reload when a negative transition on T2EX pin is detected, if timer 2 is not used to clock the serial port. Timer 2 Run Control bit Clear to turn off timer 2. Set to turn on timer 2. Timer/Counter 2 Select bit Clear for timer operation (input from internal clock system: FOSC). Set for counter operation (input from T2 input pin). Timer 2 Capture/Reload bit If RCLK=1 or TCLK=1, CP/RL2# is ignored and timer is forced to auto-reload on timer 2 overflow. Clear to auto-reload on timer 2 overflows or negative transitions on T2EX pin if EXEN2=1. Set to capture on negative transitions on T2EX pin if EXEN2=1. Reset Value = 0000 0000b Bit addressable 76 AT89C51AC3 4383A–8051–10/04 AT89C51AC3 Table 37. T2MOD Register T2MOD (S:C9h) Timer 2 Mode Control Register 7 6 5 4 3 2 1 0 - - - - - - T2OE DCEN Bit Number Bit Mnemonic Description 7 - Reserved The value read from this bit is indeterminate. Do not set this bit. 6 - Reserved The value read from this bit is indeterminate. Do not set this bit. 5 - Reserved The value read from this bit is indeterminate. Do not set this bit. 4 - Reserved The value read from this bit is indeterminate. Do not set this bit. 3 - Reserved The value read from this bit is indeterminate. Do not set this bit. 2 - Reserved The value read from this bit is indeterminate. Do not set this bit. 1 T2OE Timer 2 Output Enable bit Clear to program P1.0/T2 as clock input or I/O port. Set to program P1.0/T2 as clock output. 0 DCEN Down Counter Enable bit Clear to disable timer 2 as up/down counter. Set to enable timer 2 as up/down counter. Reset Value = XXXX XX00b Not bit addressable Table 38. TH2 Register TH2 (S:CDh) Timer 2 High Byte Register 7 6 5 4 3 2 1 0 - - - - - - - - Bit Number 7-0 Bit Mnemonic Description High Byte of Timer 2. Reset Value = 0000 0000b Not bit addressable 77 4383A–8051–10/04 Table 39. TL2 Register TL2 (S:CCh) Timer 2 Low Byte Register 7 6 5 4 3 2 1 0 - - - - - - - - Bit Number Bit Mnemonic Description 7-0 Low Byte of Timer 2. Reset Value = 0000 0000b Not bit addressable Table 40. RCAP2H Register RCAP2H (S:CBh) Timer 2 Reload/Capture High Byte Register 7 6 5 4 3 2 1 0 - - - - - - - - Bit Number Bit Mnemonic Description 7-0 High Byte of Timer 2 Reload/Capture. Reset Value = 0000 0000b Not bit addressable Table 41. RCAP2L Register RCAP2L (S:CAH) TIMER 2 REload/Capture Low Byte Register 7 6 5 4 3 2 1 0 - - - - - - - - Bit Number 7-0 Bit Mnemonic Description Low Byte of Timer 2 Reload/Capture. Reset Value = 0000 0000b Not bit addressable 78 AT89C51AC3 4383A–8051–10/04 AT89C51AC3 Watchdog Timer AT89C51AC3 contains a powerful programmable hardware Watchdog Timer (WDT) that automatically resets the chip if it software fails to reset the WDT before the selected time interval has elapsed. It permits large Time-Out ranking from 16ms to 2s @Fosc = 12MHz in X1 mode. This WDT consists of a 14-bit counter plus a 7-bit programmable counter, a Watchdog Timer reset register (WDTRST) and a Watchdog Timer programming (WDTPRG) register. When exiting reset, the WDT is -by default- disable. To enable the WDT, the user has to write the sequence 1EH and E1H into WDTRST register no instruction in between. When the Watchdog Timer is enabled, it will increment every machine cycle while the oscillator is running and there is no way to disable the WDT except through reset (either hardware reset or WDT overflow reset). When WDT overflows, it will generate an output RESET pulse at the RST pin. The RESET pulse duration is 96xTOSC, where TOSC=1/FOSC. To make the best use of the WDT, it should be serviced in those sections of code that will periodically be executed within the time required to prevent a WDT reset Note: When the Watchdog is enable it is impossible to change its period. Figure 42. Watchdog Timer Fwd CLOCK ÷ PS CPU and Peripheral Clock ÷6 Decoder RESET WR Control WDTRST Enable 14-bit COUNTER 7-bit COUNTER Fwd Clock WDTPRG Outputs - - - - - 2 1 0 RESET 79 4383A–8051–10/04 Watchdog Programming The three lower bits (S0, S1, S2) located into WDTPRG register permit to program the WDT duration. Table 42. Machine Cycle Count S2 S1 S0 Machine Cycle Count 0 0 0 214 - 1 0 0 1 215 - 1 0 1 0 216 - 1 0 1 1 217 - 1 1 0 0 218 - 1 1 0 1 219 - 1 1 1 0 220 - 1 1 1 1 221 - 1 To compute WD Time-Out, the following formula is applied: F wd FTime – Out = ----------------------------------------------------------------14 Svalue 12 × ( ( 2 × 2 ) – 1) Note: Svalue represents the decimal value of (S2 S1 S0) The following table outlines the time-out value for FoscXTAL = 12 MHz in X1 mode Table 43. Time-Out Computation 80 S2 S1 S0 Fosc = 12 MHz Fosc = 16 MHz Fosc = 20 MHz 0 0 0 16.38 ms 12.28 ms 9.82 ms 0 0 1 32.77 ms 24.57 ms 19.66 ms 0 1 0 65.54 ms 49.14 ms 39.32 ms 0 1 1 131.07 ms 98.28 ms 78.64 ms 1 0 0 262.14 ms 196.56 ms 157.28 ms 1 0 1 524.29 ms 393.12 ms 314.56 ms 1 1 0 1.05 s 786.24 ms 629.12 ms 1 1 1 2.10 s 1.57 s 1.25 s AT89C51AC3 4383A–8051–10/04 AT89C51AC3 Watchdog Timer During Power-down Mode and Idle In Power-down mode the oscillator stops, which means the WDT also stops. While in Power-down mode, the user does not need to service the WDT. There are 2 methods of exiting Power-down mode: by a hardware reset or via a level activated external interrupt which is enabled prior to entering Power-down mode. When Power-down is exited with hardware reset, the Watchdog is disabled. Exiting Power-down with an interrupt is significantly different. The interrupt shall be held low long enough for the oscillator to stabilize. When the interrupt is brought high, the interrupt is serviced. To prevent the WDT from resetting the device while the interrupt pin is held low, the WDT is not started until the interrupt is pulled high. It is suggested that the WDT be reset during the interrupt service for the interrupt used to exit Power-down. To ensure that the WDT does not overflow within a few states of exiting powerdown, it is best to reset the WDT just before entering powerdown. In the Idle mode, the oscillator continues to run. To prevent the WDT from resetting AT89C51AC3 while in Idle mode, the user should always set up a timer that will periodically exit Idle, service the WDT, and re-enter Idle mode. Register Table 44. WDTPRG Register WDTPRG (S:A7h) Watchdog Timer Duration Programming Register 7 6 5 4 3 2 1 0 – – – – – S2 S1 S0 Bit Number Bit Mnemonic Description 7 - Reserved The value read from this bit is indeterminate. Do not set this bit. 6 - Reserved The value read from this bit is indeterminate. Do not set this bit. 5 - Reserved The value read from this bit is indeterminate. Do not set this bit. 4 - Reserved The value read from this bit is indeterminate. Do not set this bit. 3 - Reserved The value read from this bit is indeterminate. Do not set this bit. 2 S2 Watchdog Timer Duration selection bit 2 Work in conjunction with bit 1 and bit 0. 1 S1 Watchdog Timer Duration selection bit 1 Work in conjunction with bit 2 and bit 0. 0 S0 Watchdog Timer Duration selection bit 0 Work in conjunction with bit 1 and bit 2. Reset Value = XXXX X000b 81 4383A–8051–10/04 Table 45. WDTRST Register WDTRST (S:A6h Write only) Watchdog Timer Enable Register 7 6 5 4 3 2 1 0 – – – – – – – – Bit Number 7 Bit Mnemonic Description - Watchdog Control Value Reset Value = 1111 1111b Note: 82 The WDRST register is used to reset/enable the WDT by writing 1EH then E1H in sequence without instruction between these two sequences. AT89C51AC3 4383A–8051–10/04 AT89C51AC3 Serial Port Interface (SPI) The Serial Peripheral Interface Module (SPI) allows full-duplex, synchronous, serial communication between the MCU and peripheral devices, including other MCUs. Features Features of the SPI Module include the following: Signal Description • Full-duplex, three-wire synchronous transfers • Master or Slave operation • Six programmable Master clock rates in master mode • Serial clock with programmable polarity and phase • Master Mode fault error flag with MCU interrupt capability Figure 43 shows a typical SPI bus configuration using one Master controller and many Slave peripherals. The bus is made of three wires connecting all the devices. Figure 43. SPI Master/Slaves Interconnection Slave 1 MISO MOSI SCK SS MISO MOSI SCK SS VDD Slave 4 Slave 3 MISO MOSI SCK SS 0 1 2 3 MISO MOSI SCK SS MISO MOSI SCK SS PORT Master Slave 2 The Master device selects the individual Slave devices by using four pins of a parallel port to control the four SS pins of the Slave devices. Master Output Slave Input (MOSI) This 1-bit signal is directly connected between the Master Device and a Slave Device. The MOSI line is used to transfer data in series from the Master to the Slave. Therefore, it is an output signal from the Master, and an input signal to a Slave. A Byte (8-bit word) is transmitted most significant bit (MSB) first, least significant bit (LSB) last. Master Input Slave Output (MISO) This 1-bit signal is directly connected between the Slave Device and a Master Device. The MISO line is used to transfer data in series from the Slave to the Master. Therefore, it is an output signal from the Slave, and an input signal to the Master. A Byte (8-bit word) is transmitted most significant bit (MSB) first, least significant bit (LSB) last. SPI Serial Clock (SCK) This signal is used to synchronize the data transmission both in and out of the devices through their MOSI and MISO lines. It is driven by the Master for eight clock cycles which allows to exchange one Byte on the serial lines. Slave Select (SS) Each Slave peripheral is selected by one Slave Select pin (SS). This signal must stay low for any message for a Slave. It is obvious that only one Master (SS high level) can drive the network. The Master may select each Slave device by software through port pins (Figure 44). To prevent bus conflicts on the MISO line, only one slave should be selected at a time by the Master for a transmission. 83 4383A–8051–10/04 In a Master configuration, the SS line can be used in conjunction with the MODF flag in the SPI Status register (SPSCR) to prevent multiple masters from driving MOSI and SCK (see Error conditions). A high level on the SS pin puts the MISO line of a Slave SPI in a high-impedance state. The SS pin could be used as a general-purpose if the following conditions are met: • The device is configured as a Master and the SSDIS control bit in SPCON is set. This kind of configuration can be found when only one Master is driving the network and there is no way that the SS pin could be pulled low. Therefore, the MODF flag in the SPSCR will never be set(1). • The Device is configured as a Slave with CPHA and SSDIS control bits set(2). This kind of configuration can happen when the system includes one Master and one Slave only. Therefore, the device should always be selected and there is no reason that the Master uses the SS pin to select the communicating Slave device. Note: 1. Clearing SSDIS control bit does not clear MODF. 2. Special care should be taken not to set SSDIS control bit when CPHA =’0’ because in this mode, the SS is used to start the transmission. Baud Rate In Master mode, the baud rate can be selected from a baud rate generator which is controlled by three bits in the SPCON register: SPR2, SPR1 and SPR0.The Master clock is selected from one of seven clock rates resulting from the division of the internal clock by 4, 8, 16, 32, 64 or 128. Table 46 gives the different clock rates selected by SPR2:SPR1:SPR0. In Slave mode, the maximum baud rate allowed on the SCK input is limited to Fsys/4 Table 46. SPI Master Baud Rate Selection 84 SPR2 SPR1 SPR0 Clock Rate Baud Rate Divisor (BD) 0 0 0 Don’t Use No BRG 0 0 1 FCLK PERIPH /4 4 0 1 0 FCLK PERIPH/8 8 0 1 1 FCLK PERIPH /16 16 1 0 0 FCLK PERIPH /32 32 1 0 1 FCLK PERIPH /64 64 1 1 0 FCLK PERIPH /128 128 1 1 1 Don’t Use No BRG AT89C51AC3 4383A–8051–10/04 AT89C51AC3 Functional Description Figure 44 shows a detailed structure of the SPI Module. Figure 44. SPI Module Block Diagram Internal Bus SPDAT Transmit Data Register Shift Register 7 6 5 4 3 2 1 0 Receive Data Register SPSCR SPIF - OVR MODF SPTE UARTM SPTEIE MODFIE Clock Logic SPI Control SPCON SPR2 SPEN SSDIS MSTR CPOL Pin Control Logic CPHA SPR1 SPR0 FCLK PERIPH M S MOSI MISO SCK SS SPI Interrupt Request 8-bit bus 1-bit signal Operating Modes The Serial Peripheral Interface can be configured in one of the two modes: Master mode or Slave mode. The configuration and initialization of the SPI Module is made through two registers: • The Serial Peripheral Control register (SPCON) • The Serial Peripheral Status and Control Register (SPSCR) Once the SPI is configured, the data exchange is made using: • The Serial Peripheral DATa register (SPDAT) During an SPI transmission, data is simultaneously transmitted (shifted out serially) and received (shifted in serially). A serial clock line (SCK) synchronizes shifting and sampling on the two serial data lines (MOSI and MISO). A Slave Select line (SS) allows individual selection of a Slave SPI device; Slave devices that are not selected do not interfere with SPI bus activities. 85 4383A–8051–10/04 When the Master device transmits data to the Slave device via the MOSI line, the Slave device responds by sending data to the Master device via the MISO line. This implies full-duplex transmission with both data out and data in synchronized with the same clock (Figure 45). Figure 45. Full-Duplex Master-Slave Interconnection 8-bit Shift register SPI Clock Generator MISO MISO MOSI MOSI SCK SS Master MCU 8-bit Shift register SCK VDD SS VSS Slave MCU Master Mode The SPI operates in Master mode when the Master bit, MSTR (1), in the SPCON register is set. Only one Master SPI device can initiate transmissions. Software begins the transmission from a Master SPI Module by writing to the Serial Peripheral Data Register (SPDAT). If the shift register is empty, the Byte is immediately transferred to the shift register. The Byte begins shifting out on MOSI pin under the control of the serial clock, SCK. Simultaneously, another Byte shifts in from the Slave on the Master’s MISO pin. The transmission ends when the Serial Peripheral transfer data flag, SPIF, in SPSCR becomes set. At the same time that SPIF becomes set, the received Byte from the Slave is transferred to the receive data register in SPDAT. Software clears SPIF by reading the Serial Peripheral Status register (SPSCR) with the SPIF bit set, and then reading the SPDAT. Slave Mode The SPI operates in Slave mode when the Master bit, MSTR (2), in the SPCON register is cleared. Before a data transmission occurs, the Slave Select pin, SS, of the Slave device must be set to’0’. SS must remain low until the transmission is complete. In a Slave SPI Module, data enters the shift register under the control of the SCK from the Master SPI Module. After a Byte enters the shift register, it is immediately transferred to the receive data register in SPDAT, and the SPIF bit is set. To prevent an overflow condition, Slave software must then read the SPDAT before another Byte enters the shift register (3). A Slave SPI must complete the write to the SPDAT (shift register) at least one bus cycle before the Master SPI starts a transmission. If the write to the data register is late, the SPI transmits the data already in the shift register from the previous transmission. Transmission Formats Software can select any of four combinations of serial clock (SCK) phase and polarity using two bits in the SPCON: the Clock Polarity (CPOL (4) ) and the Clock Phase (CPHA4). CPOL defines the default SCK line level in idle state. It has no significant effect on the transmission format. CPHA defines the edges on which the input data are sampled and the edges on which the output data are shifted (Figure 46 and Figure 47). The clock phase and polarity should be identical for the Master SPI device and the communicating Slave device. 1. The SPI Module should be configured as a Master before it is enabled (SPEN set). Also, the Master SPI should be configured before the Slave SPI. 2. 3. The SPI Module should be configured as a Slave before it is enabled (SPEN set). The maximum frequency of the SCK for an SPI configured as a Slave is the bus clock speed. Before writing to the CPOL and CPHA bits, the SPI should be disabled (SPEN =’0’). 4. 86 AT89C51AC3 4383A–8051–10/04 AT89C51AC3 Figure 46. Data Transmission Format (CPHA = 0) SCK Cycle Number 1 2 3 4 5 6 7 8 MSB bit6 bit5 bit4 bit3 bit2 bit1 LSB bit6 bit5 bit4 bit3 bit2 bit1 LSB SPEN (Internal) SCK (CPOL = 0) SCK (CPOL = 1) MOSI (from Master) MISO (from Slave) MSB SS (to Slave) Capture Point Figure 47. Data Transmission Format (CPHA = 1) 1 2 3 4 5 6 7 8 MOSI (from Master) MSB bit6 bit5 bit4 bit3 bit2 bit1 LSB MISO (from Slave) MSB bit6 bit5 bit4 bit3 bit2 bit1 SCK Cycle Number SPEN (Internal) SCK (CPOL = 0) SCK (CPOL = 1) LSB SS (to Slave) Capture Point Figure 48. CPHA/SS Timing MISO/MOSI Byte 1 Byte 2 Byte 3 Master SS Slave SS (CPHA = 0) Slave SS (CPHA = 1) As shown in Figure 46, the first SCK edge is the MSB capture strobe. Therefore, the Slave must begin driving its data before the first SCK edge, and a falling edge on the SS pin is used to start the transmission. The SS pin must be toggled high and then low between each Byte transmitted (Figure 48). Figure 47 shows an SPI transmission in which CPHA is ’1’. In this case, the Master begins driving its MOSI pin on the first SCK edge. Therefore, the Slave uses the first SCK edge as a start transmission signal. The SS pin can remain low between transmissions (Figure 48). This format may be preferred in systems having only one Master and only one Slave driving the MISO data line. Queuing transmission For an SPI configured in master or slave mode, a queued data byte must be transmitted/received immediately after the previous transmission has completed. 87 4383A–8051–10/04 When a transmission is in progress a new data can be queued and sent as soon as transmission has been completed. So it is possible to transmit bytes without latency, useful in some applications. The SPTE bit in SPSCR is set as long as the transmission buffer is free. It means that the user application can write SPDAT with the data to be transmitted until the SPTE becomes cleared. Figure 49 shows a queuing transmission in master mode. Once the Byte 1 is ready, it is immediately sent on the bus. Meanwhile an other byte is prepared (and the SPTE is cleared), it will be sent at the end of the current transmission. The next data must be ready before the end of the current transmission. Figure 49. Queuing Transmission In Master Mode SCK MOSI MSB B6 B5 B4 B3 B2 B1 LSB MSB B6 B5 B4 B3 B2 B1 LSB MISO MSB B6 B5 B4 B3 B2 B1 LSB MSB B6 B5 B4 B3 B2 B1 LSB Data Byte 1 Byte 2 BYTE 1 under transmission Byte 3 BYTE 2 under transmission SPTE In slave mode it is almost the same except it is the external master that start the transmission. Also, in slave mode, if no new data is ready, the last value received will be the next data byte transmitted. 88 AT89C51AC3 4383A–8051–10/04 AT89C51AC3 Error Conditions The following flags in the SPSCR register indicate the SPI error conditions: Mode Fault Error (MODF) Mode Fault error in Master mode SPI indicates that the level on the Slave Select (SS) pin is inconsistent with the actual mode of the device. • Mode fault detection in Master mode: MODF is set to warn that there may be a multi-master conflict for system control. In this case, the SPI system is affected in the following ways: – An SPI receiver/error CPU interrupt request is generated – The SPEN bit in SPCON is cleared. This disables the SPI – The MSTR bit in SPCON is cleared Clearing the MODF bit is accomplished by a read of SPSCR register with MODF bit set, followed by a write to the SPCON register. SPEN Control bit may be restored to its original set state after the MODF bit has been cleared. Figure 50. Mode Fault Conditions in Master Mode (Cpha =’1’/Cpol =’0’) 0 1 2 1 z 0 MSB B6 MISO (from slave) 1 z 0 MSB B6 SPI enable 1 z 0 SS (master) 1 z 0 SS (slave) 1 z 0 SCK cycle # SCK (from master) MOSI (from master) • 0 3 1 z 0 MODF detected Note: 0 B5 MODF detected When SS is discarded (SS disabled) it is not possible to detect a MODF error in master mode because the SPI is internally unselected and the SS pin is a general purpose I/O. Mode fault detection in Slave mode In slave mode, the MODF error is detected when SS goes high during a transmission. A transmission begins when SS goes low and ends once the incoming SCK goes back to its idle level following the shift of the eighteen data bit. A MODF error occurs if a slave is selected (SS is low) and later unselected (SS is high) even if no SCK is sent to that slave. At any time, a ’1’ on the SS pin of a slave SPI puts the MISO pin in a high impedance state and internal state counter is cleared. Also, the slave SPI ignores all incoming SCK clocks, even if it was already in the middle of a transmission. A new transmission will be performed as soon as SS pin returns low. 89 4383A–8051–10/04 Figure 51. Mode Fault Conditions in Slave Mode 0 SCK cycle # SCK (from master) MOSI (from master) 0 OverRun Condition 2 3 4 MSB B6 B5 B4 1 z 0 1 z 0 MISO (from slave) 1 z 0 SS (slave) 1 z 0 MSB MSB MODF detected Note: 1 B6 MODF detected when SS is discarded (SS disabled) it is not possible to detect a MODF error in slave mode because the SPI is internally selected. Also the SS pin becomes a general purpose I/O. This error mean that the speed is not adapted for the running application: An OverRun condition occurs when a byte has been received whereas the previous one has not been read by the application yet. The last byte (which generate the overrun error) does not overwrite the unread data so that it can still be read. Therefore, an overrun error always indicates the loss of data. Interrupts Three SPI status flags can generate a CPU interrupt requests: Table 47. SPI Interrupts Flag Request SPIF (SPI data transfer) SPI Transmitter Interrupt Request MODF (Mode Fault) SPI mode-fault Interrupt Request SPTE (Transmit register empty) SPI transmit register empty Interrupt Request Serial Peripheral data transfer flag, SPIF: This bit is set by hardware when a transfer has been completed. SPIF bit generates transmitter CPU interrupt request only when SPTEIE is disabled. Mode Fault flag, MODF: This bit is set to indicate that the level on the SS is inconsistent with the mode of the SPI (in both master and slave modes). Serial Peripheral Transmit Register empty flag, SPTE: This bit is set when the transmit buffer is empty (other data can be loaded is SPDAT). SPTE bit generates transmitter CPU interrupt request only when SPTEIE is enabled. Note: While using SPTE interruption for “burst mode” transfers (SPTEIE=’1’), the user software application should take care to clear SPTEIE, during the last but one data reception (to be able to generate an interrupt on SPIF flag at the end of the last data reception). 90 AT89C51AC3 4383A–8051–10/04 AT89C51AC3 Figure 52. SPI Interrupt Requests Generation SPIF SPTEIE SPI CPU Interrupt Request SPTE MODFIE MODF Registers Three registers in the SPI module provide control, status and data storage functions. These registers are describe in the following paragraphs. Serial Peripheral Control Register (SPCON) • The Serial Peripheral Control Register does the following: • Selects one of the Master clock rates • Configure the SPI Module as Master or Slave • Selects serial clock polarity and phase • Enables the SPI Module • Frees the SS pin for a general-purpose Table 48 describes this register and explains the use of each bit Table 48. SPCON Register SPCON - Serial Peripheral Control Register (0D4H) 7 6 5 4 3 2 1 0 SPR2 SPEN SSDIS MSTR CPOL CPHA SPR1 SPR0 Bit Number Bit Mnemonic 7 SPR2 6 SPEN Description Serial Peripheral Rate 2 Bit with SPR1 and SPR0 define the clock rate (See bits SPR1 and SPR0 for detail). Serial Peripheral Enable Cleared to disable the SPI interface (internal reset of the SPI). Set to enable the SPI interface. SS Disable Cleared to enable SS in both Master and Slave modes. 5 SSDIS 4 MSTR Set to disable SS in both Master and Slave modes. In Slave mode, this bit has no effect if CPHA =’0’. When SSDIS is set, no MODF interrupt request is generated. Serial Peripheral Master Cleared to configure the SPI as a Slave. Set to configure the SPI as a Master. 91 4383A–8051–10/04 Bit Number Bit Mnemonic 3 CPOL Description Clock Polarity Cleared to have the SCK set to ’0’ in idle state. Set to have the SCK set to ’1’ in idle state. Clock Phase 2 Cleared to have the data sampled when the SCK leaves the idle state (see CPOL). CPHA Set to have the data sampled when the SCK returns to idle state (see CPOL). 1 SPR1 0 SPR0 SPR2 SPR1 SPR0 Serial Peripheral Rate 0 0 0 0 0 1 FCLK PERIPH /4 0 1 0 FCLK PERIPH /8 0 1 1 FCLK PERIPH /16 1 0 0 FCLK PERIPH /32 1 0 1 FCLK PERIPH /64 1 1 0 FCLK PERIPH /128 1 1 1 Invalid Invalid Reset Value = 0001 0100b Not bit addressable Serial Peripheral Status Register and Control (SPSCR) The Serial Peripheral Status Register contains flags to signal the following conditions: • Data transfer complete • Write collision • Inconsistent logic level on SS pin (mode fault error) Table 49. SPSCR Register SPSCR - Serial Peripheral Status and Control register (0D5H) 7 6 5 4 3 2 1 0 SPIF - OVR MODF SPTE UARTM SPTEIE MODFIE Bit Number Bit Mnemonic Description Serial Peripheral Data Transfer Flag 7 SPIF Cleared by hardware to indicate data transfer is in progress or has been approved by a clearing sequence. Set by hardware to indicate that the data transfer has been completed. This bit is cleared when reading or writing SPDATA after reading SPSCR. 6 - Reserved The value read from this bit is indeterminate. Do not set this bit. Overrun Error Flag 5 OVR - Set by hardware when a byte is received whereas SPIF is set (the previous received data is not overwritten). - Cleared by hardware when reading SPSCR 92 AT89C51AC3 4383A–8051–10/04 AT89C51AC3 Bit Number Bit Mnemonic Description Mode Fault - Set by hardware to indicate that the SS pin is in inappropriate logic level (in both master and slave modes). - Cleared by hardware when reading SPSCR 4 MODF When MODF error occurred: - In slave mode: SPI interface ignores all transmitted data while SS remains high. A new transmission is perform as soon as SS returns low. - In master mode: SPI interface is disabled (SPEN=0, see description for SPEN bit in SPCON register). Serial Peripheral Transmit register Empty 3 SPTE - Set by hardware when transmit register is empty (if needed, SPDAT can be loaded with another data). - Cleared by hardware when transmit register is full (no more data should be loaded in SPDAT). Serial Peripheral UART mode 2 UARTM Set and cleared by software: - Clear: Normal mode, data are transmitted MSB first (default) - Set: UART mode, data are transmitted LSB first. Interrupt Enable for SPTE Set and cleared by software: 1 SPTEIE - Set to enable SPTE interrupt generation (when SPTE goes high, an interrupt is generated). - Clear to disable SPTE interrupt generation Caution: When SPTEIE is set no interrupt generation occurred when SPIF flag goes high. To enable SPIF interrupt again, SPTEIE should be cleared. Interrupt Enable for MODF 0 MODFIE Set and cleared by software: - Set to enable MODF interrupt generation - Clear to disable MODF interrupt generation Reset Value = 00X0 XXXXb Not Bit addressable 93 4383A–8051–10/04 Programmable Counter Array (PCA) The PCA provides more timing capabilities with less CPU intervention than the standard timer/counters. Its advantages include reduced software overhead and improved accuracy. The PCA consists of a dedicated timer/counter which serves as the time base for an array of five compare/capture modules. Its clock input can be programmed to count any of the following signals: • PCA clock frequency/6 (see “clock” section) • PCA clock frequency/2 • Timer 0 overflow • External input on ECI (P1.2) Each compare/capture modules can be programmed in any one of the following modes: • rising and/or falling edge capture, • software timer, • high-speed output, • pulse width modulator. Module 4 can also be programmed as a WatchDog timer. see the "PCA WatchDog Timer" section. When the compare/capture modules are programmed in capture mode, software timer, or high speed output mode, an interrupt can be generated when the module executes its function. All five modules plus the PCA timer overflow share one interrupt vector. The PCA timer/counter and compare/capture modules share Port 1 for external I/Os. These pins are listed below. If the port is not used for the PCA, it can still be used for standard I/O. PCA Timer 94 PCA Component External I/O Pin 16-bit Counter P1.2/ECI 16-bit Module 0 P1.3/CEX0 16-bit Module 1 P1.4/CEX1 16-bit Module 2 P1.5/CEX2 16-bit Module 3 P1.6/CEX3 16-bit Module 4 P1.7/CEX4 The PCA timer is a common time base for all five modules (see Figure 53). The timer count source is determined from the CPS1 and CPS0 bits in the CMOD SFR (see Table 8) and can be programmed to run at: • 1/6 the PCA clock frequency. • 1/2 the PCA clock frequency. • the Timer 0 overflow. • the input on the ECI pin (P1.2). AT89C51AC3 4383A–8051–10/04 AT89C51AC3 Figure 53. PCA Timer/Counter To PCA modules FPca/6 overflow FPca/2 CH T0 OVF It CL 16 bit up counter P1.2 CIDL WDTE CF CR CPS1 CPS0 ECF CMOD 0xD9 Idle CCF4 CCF3 CCF2 CCF1 CCF0 CCON 0xD8 The CMOD register includes three additional bits associated with the PCA. • The CIDL bit which allows the PCA to stop during idle mode. • The WDTE bit which enables or disables the WatchDog function on module 4. • The ECF bit which when set causes an interrupt and the PCA overflow flag CF in CCON register to be set when the PCA timer overflows. The CCON register contains the run control bit for the PCA and the flags for the PCA timer and each module. PCA Modules • The CR bit must be set to run the PCA. The PCA is shut off by clearing this bit. • The CF bit is set when the PCA counter overflows and an interrupt will be generated if the ECF bit in CMOD register is set. The CF bit can only be cleared by software. • The CCF0:4 bits are the flags for the modules (CCF0 for module0...) and are set by hardware when either a match or a capture occurs. These flags also can be cleared by software. Each one of the five compare/capture modules has six possible functions. It can perform: • 16-bit Capture, positive-edge triggered • 16-bit Capture, negative-edge triggered • 16-bit Capture, both positive and negative-edge triggered • 16-bit Software Timer • 16-bit High Speed Output • 8-bit Pulse Width Modulator. In addition module 4 can be used as a WatchDog Timer. 95 4383A–8051–10/04 Each module in the PCA has a special function register associated with it (CCAPM0 for module 0 ...). The CCAPM0:4 registers contain the bits that control the mode that each module will operate in. • The ECCF bit enables the CCF flag in the CCON register to generate an interrupt when a match or compare occurs in the associated module. • The PWM bit enables the pulse width modulation mode. • The TOG bit when set causes the CEX output associated with the module to toggle when there is a match between the PCA counter and the module’s capture/compare register. • The match bit MAT when set will cause the CCFn bit in the CCON register to be set when there is a match between the PCA counter and the module’s capture/compare register. • The two bits CAPN and CAPP in CCAPMn register determine the edge that a capture input will be active on. The CAPN bit enables the negative edge, and the CAPP bit enables the positive edge. If both bits are set both edges will be enabled. • The bit ECOM in CCAPM register when set enables the comparator function. PCA Interrupt Figure 54. PCA Interrupt System CF CR CCF4 CCF3 CCF2 CCF1 CCF0 CCON PCA Timer/Counter Module 0 Module 1 To Interrupt Module 2 Module 3 Module 4 ECF CMOD.0 PCA Capture Mode 96 ECCFn EC EA CCAPMn.0 IEN0.6 IEN0.7 To use one of the PCA modules in capture mode either one or both of the CCAPM bits CAPN and CAPP for that module must be set. The external CEX input for the module (on port 1) is sampled for a transition. When a valid transition occurs the PCA hardware loads the value of the PCA counter registers (CH and CL) into the module’s capture registers (CCAPnL and CCAPnH). If the CCFn bit for the module in the CCON SFR and the ECCFn bit in the CCAPMn SFR are set then an interrupt will be generated. AT89C51AC3 4383A–8051–10/04 AT89C51AC3 Figure 55. PCA Capture Mode PCA Counter CH CL (8bits) (8bits) CEXn n = 0, 4 CCAPnH CCAPnL PCA Interrupt Request CCFn CCON - 0CAPPn CAPNn 000 ECCFn 0 7 CCAPMn Register (n = 0, 4) 16-bit Software Timer Mode The PCA modules can be used as software timers by setting both the ECOM and MAT bits in the modules CCAPMn register. The PCA timer will be compared to the module’s capture registers and when a match occurs an interrupt will occur if the CCFn (CCON SFR) and the ECCFn (CCAPMn SFR) bits for the module are both set. Figure 56. PCA 16-bit Software Timer and High Speed Output Mode PCA Counter CH CL (8 bits) (8 bits) Compare/Capture Module CCAPnL CCAPnH (8 bits) (8 bits) Match Toggle 16-Bit Comparator CEXn Enable CCFn CCON reg 7 “0” Reset Write to CCAPnL “1” PCA Interrupt Request ECOMn0 0 MATn TOGn0 ECCFn 0 CCAPMn Register (n = 0, 4) For software Timer mode, set ECOMn and MATn. For high speed output mode, set ECOMn, MATn and TOGn. Write to CCAPnH 97 4383A–8051–10/04 High Speed Output Mode In this mode the CEX output (on port 1) associated with the PCA module will toggle each time a match occurs between the PCA counter and the module’s capture registers. To activate this mode the TOG, MAT, and ECOM bits in the module’s CCAPMn SFR must be set. Figure 57. PCA High Speed Output Mode CCON CF Write to CCAPnH CR CCF4 CCF3 CCF2 CCF1 CCF0 0xD8 Reset PCA IT Write to CCAPnL “0” CCAPnH “1” CCAPnL Enable 16-bit comparator CH Match CL CEXn PCA counter/timer ECOMn CAPPn CAPNn MATn TOGn PWMn ECCFn Pulse Width Modulator Mode 98 CCAPMn, n = 0 to 4 0xDA to 0xDE All the PCA modules can be used as PWM outputs. The output frequency depends on the source for the PCA timer. All the modules will have the same output frequency because they all share the PCA timer. The duty cycle of each module is independently variable using the module’s capture register CCAPLn. When the value of the PCA CL SFR is less than the value in the module’s CCAPLn SFR the output will be low, when it is equal to or greater than it, the output will be high. When CL overflows from FF to 00, CCAPLn is reloaded with the value in CCAPHn. the allows the PWM to be updated without glitches. The PWM and ECOM bits in the module’s CCAPMn register must be set to enable the PWM mode. AT89C51AC3 4383A–8051–10/04 AT89C51AC3 Figure 58. PCA PWM Mode CCAPnH CL rolls over from FFh TO 00h loads CCAPnH contents into CCAPnL CCAPnL “0” CL < CCAPnL 8-Bit Comparator CL (8 bits) CEX CL > = CCAPnL “1” PCA WatchDog Timer ECOMn PWMn CCAPMn.6 CCAPMn.1 An on-board WatchDog timer is available with the PCA to improve system reliability without increasing chip count. WatchDog timers are useful for systems that are sensitive to noise, power glitches, or electrostatic discharge. Module 4 is the only PCA module that can be programmed as a WatchDog. However, this module can still be used for other modes if the WatchDog is not needed. The user pre-loads a 16-bit value in the compare registers. Just like the other compare modes, this 16-bit value is compared to the PCA timer value. If a match is allowed to occur, an internal reset will be generated. This will not cause the RST pin to be driven high. To hold off the reset, the user has three options: • periodically change the compare value so it will never match the PCA timer, • periodically change the PCA timer value so it will never match the compare values, or • disable the WatchDog by clearing the WDTE bit before a match occurs and then reenable it. The first two options are more reliable because the WatchDog timer is never disabled as in the third option. If the program counter ever goes astray, a match will eventually occur and cause an internal reset. If other PCA modules are being used the second option not recommended either. Remember, the PCA timer is the time base for all modules; changing the time base for other modules would not be a good idea. Thus, in most applications the first solution is the best option. 99 4383A–8051–10/04 PCA Registers Table 50. CMOD Register CMOD (S:D9h) PCA Counter Mode Register 7 6 5 4 3 2 1 0 CIDL WDTE - - - CPS1 CPS0 ECF Bit Number Bit Mnemonic Description PCA Counter Idle Control bit Clear to let the PCA run during Idle mode. Set to stop the PCA when Idle mode is invoked. 7 CIDL 6 WDTE 5 - Reserved The value read from this bit is indeterminate. Do not set this bit. 4 - Reserved The value read from this bit is indeterminate. Do not set this bit. 3 - Reserved The value read from this bit is indeterminate. Do not set this bit. 2-1 CPS1:0 0 ECF WatchDog Timer Enable Clear to disable WatchDog Timer function on PCA Module 4, Set to enable it. EWC Count Pulse Select bits CPS1 CPS0 Clock source 0 0 Internal Clock, FPca/6 0 1 Internal Clock, FPca/2 1 0 Timer 0 overflow 1 1 External clock at ECI/P1.2 pin (Max. Rate = FPca/4) Enable PCA Counter Overflow Interrupt bit Clear to disable CF bit in CCON register to generate an interrupt. Set to enable CF bit in CCON register to generate an interrupt. Reset Value = 00XX X000b 100 AT89C51AC3 4383A–8051–10/04 AT89C51AC3 Table 51. CCON Register CCON (S:D8h) PCA Counter Control Register 7 6 5 4 3 2 1 0 CF CR - CCF4 CCF3 CCF2 CCF1 CCF0 Bit Number Bit Mnemonic Description 7 CF PCA Timer/Counter Overflow flag Set by hardware when the PCA Timer/Counter rolls over. This generates a PCA interrupt request if the ECF bit in CMOD register is set. Must be cleared by software. 6 CR PCA Timer/Counter Run Control bit Clear to turn the PCA Timer/Counter off. Set to turn the PCA Timer/Counter on. 5 - 4 CCF4 PCA Module 4 Compare/Capture flag Set by hardware when a match or capture occurs. This generates a PCA interrupt request if the ECCF 4 bit in CCAPM 4 register is set. Must be cleared by software. 3 CCF3 PCA Module 3 Compare/Capture flag Set by hardware when a match or capture occurs. This generates a PCA interrupt request if the ECCF 3 bit in CCAPM 3 register is set. Must be cleared by software. 2 CCF2 PCA Module 2 Compare/Capture flag Set by hardware when a match or capture occurs. This generates a PCA interrupt request if the ECCF 2 bit in CCAPM 2 register is set. Must be cleared by software. 1 CCF1 PCA Module 1 Compare/Capture flag Set by hardware when a match or capture occurs. This generates a PCA interrupt request if the ECCF 1 bit in CCAPM 1 register is set. Must be cleared by software. 0 CCF0 PCA Module 0 Compare/Capture flag Set by hardware when a match or capture occurs. This generates a PCA interrupt request if the ECCF 0 bit in CCAPM 0 register is set. Must be cleared by software. Reserved The value read from this bit is indeterminate. Do not set this bit. Reset Value = 00X0 0000b 101 4383A–8051–10/04 Table 52. CCAPnH Registers CCAP0H (S:FAh) CCAP1H (S:FBh) CCAP2H (S:FCh) CCAP3H (S:FDh) CCAP4H (S:FEh) PCA High Byte Compare/Capture Module n Register (n=0..4) 7 6 5 4 3 2 1 0 CCAPnH 7 CCAPnH 6 CCAPnH 5 CCAPnH 4 CCAPnH 3 CCAPnH 2 CCAPnH 1 CCAPnH 0 Bit Number 7:0 Bit Mnemonic Description CCAPnH 7:0 High byte of EWC-PCA comparison or capture values Reset Value = 0000 0000b Table 53. CCAPnL Registers CCAP0L (S:EAh) CCAP1L (S:EBh) CCAP2L (S:ECh) CCAP3L (S:EDh) CCAP4L (S:EEh) PCA Low Byte Compare/Capture Module n Register (n=0..4) 7 6 5 4 3 2 1 0 CCAPnL 7 CCAPnL 6 CCAPnL 5 CCAPnL 4 CCAPnL 3 CCAPnL 2 CCAPnL 1 CCAPnL 0 Bit Number 7:0 Bit Mnemonic Description CCAPnL 7:0 Low byte of EWC-PCA comparison or capture values Reset Value = 0000 0000b 102 AT89C51AC3 4383A–8051–10/04 AT89C51AC3 Table 54. CCAPMn Registers CCAPM0 (S:DAh) CCAPM1 (S:DBh) CCAPM2 (S:DCh) CCAPM3 (S:DDh) CCAPM4 (S:DEh) PCA Compare/Capture Module n Mode registers (n=0..4) 7 6 5 4 3 2 1 0 - ECOMn CAPPn CAPNn MATn TOGn PWMn ECCFn Bit Number 7 Bit Mnemonic Description - Reserved The Value read from this bit is indeterminate. Do not set this bit. 6 ECOMn Enable Compare Mode Module x bit Clear to disable the Compare function. Set to enable the Compare function. The Compare function is used to implement the software Timer, the high-speed output, the Pulse Width Modulator (PWM) and the WatchDog Timer (WDT). 5 CAPPn Capture Mode (Positive) Module x bit Clear to disable the Capture function triggered by a positive edge on CEXx pin. Set to enable the Capture function triggered by a positive edge on CEXx pin 4 CAPNn Capture Mode (Negative) Module x bit Clear to disable the Capture function triggered by a negative edge on CEXx pin. Set to enable the Capture function triggered by a negative edge on CEXx pin. 3 MATn Match Module x bit Set when a match of the PCA Counter with the Compare/Capture register sets CCFx bit in CCON register, flagging an interrupt. 2 TOGn Toggle Module x bit The toggle mode is configured by setting ECOMx, MATx and TOGx bits. Set when a match of the PCA Counter with the Compare/Capture register toggles the CEXx pin. 1 PWMn Pulse Width Modulation Module x Mode bit Set to configure the module x as an 8-bit Pulse Width Modulator with output waveform on CEXx pin. 0 ECCFn Enable CCFx Interrupt bit Clear to disable CCFx bit in CCON register to generate an interrupt request. Set to enable CCFx bit in CCON register to generate an interrupt request. Reset Value = X000 0000b 103 4383A–8051–10/04 Table 55. CH Register CH (S:F9h) PCA Counter Register High Value 7 6 5 4 3 2 1 0 CH 7 CH 6 CH 5 CH 4 CH 3 CH 2 CH 1 CH 0 Bit Number 7:0 Bit Mnemonic Description CH 7:0 High byte of Timer/Counter Reset Value = 0000 00000b Table 56. CL Register CL (S:E9h) PCA counter Register Low Value 7 6 5 4 3 2 1 0 CL 7 CL 6 CL 5 CL 4 CL 3 CL 2 CL 1 CL 0 Bit Number 7:0 Bit Mnemonic Description CL0 7:0 Low byte of Timer/Counter Reset Value = 0000 00000b 104 AT89C51AC3 4383A–8051–10/04 AT89C51AC3 Analog-to-Digital Converter (ADC) This section describes the on-chip 10 bit analog-to-digital converter of the AT89C51AC3. Eight ADC channels are available for sampling of the external sources AN0 to AN7. An analog multiplexer allows the single ADC converter to select one from the 8 ADC channels as ADC input voltage (ADCIN). ADCIN is converted by the 10-bit cascaded potentiometric ADC. Two kinds of conversion are available: - Standard conversion (8 bits). - Precision conversion (10 bits). For the precision conversion, set bit PSIDLE in ADCON register and start conversion. The device is in a pseudo-idle mode, the CPU does not run but the peripherals are always running. This mode allows digital noise to be as low as possible, to ensure high precision conversion. For this mode it is necessary to work with end of conversion interrupt, which is the only way to wake the device up. If another interrupt occurs during the precision conversion, it will be treated only after this conversion is ended. Features ADC Port1 I/O Functions • 8 channels with multiplexed inputs • 10-bit cascaded potentiometric ADC • Conversion time 16 micro-seconds (typ.) • Zero Error (offset) ± 2 LSB max • Positive External Reference Voltage Range (VREF) 2.4 to 3.0Volt (typ.) • ADCIN Range 0 to 3Volt • Integral non-linearity typical 1 LSB, max. 2 LSB • Differential non-linearity typical 0.5 LSB, max. 1 LSB • Conversion Complete Flag or Conversion Complete Interrupt • Selectable ADC Clock Port 1 pins are general I/O that are shared with the ADC channels. The channel select bit in ADCF register define which ADC channel/port1 pin will be used as ADCIN. The remaining ADC channels/port1 pins can be used as general-purpose I/O or as the alternate function that is available. A conversion launched on a channel which are not selected on ADCF register will not have any effect. 105 4383A–8051–10/04 Figure 59. ADC Description ADCON.5 ADCON.3 ADEN ADSST ADC Interrupt Request ADCON.4 ADEOC ADC CLOCK CONTROL EADC AN0/P1.0 000 AN1/P1.1 001 AN2/P1.2 010 AN3/P1.3 011 AN4/P1.4 100 AN5/P1.5 101 AN6/P1.6 110 AN7/P1.7 IEN1.1 ADCIN 8 ADDH 2 ADDL + SAR - AVSS Sample and Hold 111 10 R/2R DAC SCH2 SCH1 SCH0 ADCON.2 ADCON.1 ADCON.0 VAREF VAGND Figure 60 shows the timing diagram of a complete conversion. For simplicity, the figure depicts the waveforms in idealized form and do not provide precise timing information. For ADC characteristics and timing parameters refer to the Section “AC Characteristics” of the AT89C51AC3 datasheet. Figure 60. Timing Diagram CLK ADEN TSETUP ADSST TCONV ADEOC Note: 106 Tsetup min = 4 us Tconv=11 clock ADC = 1sample and hold + 10 bit conversion The user must ensure that 4 us minimum time between setting ADEN and the start of the first conversion. AT89C51AC3 4383A–8051–10/04 AT89C51AC3 ADC Converter Operation A start of single A/D conversion is triggered by setting bit ADSST (ADCON.3). After completion of the A/D conversion, the ADSST bit is cleared by hardware. The end-of-conversion flag ADEOC (ADCON.4) is set when the value of conversion is available in ADDH and ADDL, it must be cleared by software. If the bit EADC (IEN1.1) is set, an interrupt occur when flag ADEOC is set (see Figure 62). Clear this flag for rearming the interrupt. The bits SCH0 to SCH2 in ADCON register are used for the analog input channel selection. Table 57. Selected Analog input Voltage Conversion SCH2 SCH1 SCH0 Selected Analog input 0 0 0 AN0 0 0 1 AN1 0 1 0 AN2 0 1 1 AN3 1 0 0 AN4 1 0 1 AN5 1 1 0 AN6 1 1 1 AN7 When the ADCIN is equals to VAREF the ADC converts the signal to 3FFh (full scale). If the input voltage equals VAGND, the ADC converts it to 000h. Input voltage between VAREF and VAGND are a straight-line linear conversion. All other voltages will result in 3FFh if greater than VAREF and 000h if less than VAGND. Note that ADCIN should not exceed VAREF absolute maximum range! (See section “AC-DC”) Clock Selection The ADC clock is the same as CPU. The typical maximum clock frequency for ADC is 700 KHz. A prescaler is featured (ADCCLK) to generate the ADC clock from the oscillator frequency. Figure 61. A/D Converter clock CPU CLOCK ÷2 CPU Core Clock Symbol ADC Standby Mode Prescaler ADCLK ADC Clock A/D Converter When the ADC is not used, it is possible to set it in standby mode by clearing bit ADEN in ADCON register. In this mode its power dissipation is about 1 µW. 107 4383A–8051–10/04 IT ADC Management An interrupt end-of-conversion will occurs when the bit ADEOC is activated and the bit EADC is set. For re-arming the interrupt the bit ADEOC must be cleared by software. Figure 62. ADC Interrupt Structure ADCI ADEOC ADCON.2 EADC IEN1.1 Routines examples 1. Configure P1.2 and P1.3 in ADC channels // configure channel P1.2 and P1.3 for ADC ADCF = 0Ch // Enable the ADC ADCON = 20h 2. Start a standard conversion // The variable "channel" contains the channel to convert // The variable "value_converted" is an unsigned int // Clear the field SCH[2:0] ADCON and = F8h // Select channel ADCON | = channel // Start conversion in standard mode ADCON | = 08h // Wait flag End of conversion while((ADCON and 01h)! = 01h) // Clear the End of conversion flag ADCON and = EFh // read the value value_converted = (ADDH << 2)+(ADDL) 3. Start a precision conversion (need interrupt ADC) // The variable "channel" contains the channel to convert // Enable ADC EADC = 1 // clear the field SCH[2:0] ADCON and = F8h // Select the channel ADCON | = channel // Start conversion in precision mode ADCON | = 48h Note: 108 to enable the ADC interrupt: EA = 1 AT89C51AC3 4383A–8051–10/04 AT89C51AC3 Registers Table 58. ADCF Register ADCF (S:F6h) ADC Configuration 7 6 5 4 3 2 1 0 CH 7 CH 6 CH 5 CH 4 CH 3 CH 2 CH 1 CH 0 Bit Number 7-0 Bit Mnemonic Description CH 0:7 Channel Configuration Set to use P1.x as ADC input. Clear to use P1.x as standart I/O port. Reset Value =0000 0000b Table 59. ADCON Register ADCON (S:F3h) ADC Control Register 7 6 5 4 3 2 1 0 - PSIDLE ADEN ADEOC ADSST SCH2 SCH1 SCH0 Bit Number Bit Mnemonic Description 7 - 6 PSIDLE 5 ADEN Pseudo Idle Mode (Best Precision) Set to put in idle mode during conversion Clear to convert without idle mode. Enable/Standby Mode Set to enable ADC Clear for Standby mode (power dissipation 1 uW). 4 ADEOC End Of Conversion Set by hardware when ADC result is ready to be read. This flag can generate an interrupt. Must be cleared by software. 3 ADSST Start and Status Set to start an A/D conversion. Cleared by hardware after completion of the conversion 2-0 SCH2:0 Selection of Channel to Convert see Table 57 Reset Value =X000 0000b 109 4383A–8051–10/04 Table 60. ADCLK Register ADCLK (S:F2h) ADC Clock Prescaler 7 6 5 4 3 2 1 0 - - - PRS 4 PRS 3 PRS 2 PRS 1 PRS 0 Bit Number Bit Mnemonic Description 7-5 - 4-0 PRS4:0 Reserved The value read from these bits are indeterminate. Do not set these bits. Clock Prescaler See Note (1) Reset Value = XXX0 0000b Note: 1. In X1 mode: For PRS > 0 FADC = FXTAL 4xPRS For PRS = 0 FADC = FXTAL 128 In X2 mode: For PRS > 0 FADC = FXTAL 2xPRS For PRS = 0 FADC = FXTAL 64 Table 61. ADDH Register ADDH (S:F5h Read Only) ADC Data High Byte Register 7 6 5 4 3 2 1 0 ADAT 9 ADAT 8 ADAT 7 ADAT 6 ADAT 5 ADAT 4 ADAT 3 ADAT 2 Bit Number 7-0 Bit Mnemonic Description ADAT9:2 ADC result bits 9-2 Reset Value = 00h Table 62. ADDL Register ADDL (S:F4h Read Only) ADC Data Low Byte Register 110 7 6 5 4 3 2 1 0 - - - - - - ADAT 1 ADAT 0 AT89C51AC3 4383A–8051–10/04 AT89C51AC3 Bit Number Bit Mnemonic Description 7-2 - 1-0 ADAT1:0 Reserved The value read from these bits are indeterminate. Do not set these bits. ADC result bits 1-0 Reset Value = 00h 111 4383A–8051–10/04 Interrupt System Introduction The Micro-controller has a total of 9 interrupt vectors: two external interrupts (INT0 and INT1), three timer interrupts (timers 0, 1 and 2), a serial port interrupt, a PCA, a timer overrun interrupt and an ADC. These interrupts are shown below. Figure 63. Interrupt Control System INT0# 00 01 10 11 External Interrupt 0 Highest Priority Interrupts EX0 00 01 10 11 IEN0.0 Timer 0 ET0 00 01 10 11 IEN0.1 INT1# External Interrupt 1 EX1 00 01 10 11 IEN0.2 Timer 1 ET1 CEX0:5 PCA 00 01 10 11 IEN0.3 EC TxD UART 00 01 10 11 IEN0.6 RxD ES IEN0.4 00 01 10 11 Timer 2 ET2 IEN0.5 AIN1:0 00 01 10 11 A to D Converter EADC IEN1.1 00 01 10 11 SPI Controller ESPI EA IEN1.3 IEN0.7 Interrupt Enable 112 IPH/L Priority Enable Lowest Priority Interrupts AT89C51AC3 4383A–8051–10/04 AT89C51AC3 Each of the interrupt sources can be individually enabled or disabled by setting or clearing a bit in the Interrupt Enable register. This register also contains a global disable bit which must be cleared to disable all the interrupts at the same time. Each interrupt source can also be individually programmed to one of four priority levels by setting or clearing a bit in the Interrupt Priority registers. The Table below shows the bit values and priority levels associated with each combination. Table 63. Priority Level Bit Values IPH.x IPL.x Interrupt Level Priority 0 0 0 (Lowest) 0 1 1 1 0 2 1 1 3 (Highest) A low-priority interrupt can be interrupted by a high priority interrupt but not by another low-priority interrupt. A high-priority interrupt cannot be interrupted by any other interrupt source. If two interrupt requests of different priority levels are received simultaneously, the request of the higher priority level is serviced. If interrupt requests of the same priority level are received simultaneously, an internal polling sequence determines which request is serviced. Thus within each priority level there is a second priority structure determined by the polling sequence, see Table 64. Table 64. Interrupt priority Within level Interrupt Name Interrupt Address Vector Priority Number external interrupt (INT0) 0003h 1 Timer0 (TF0) 000Bh 2 external interrupt (INT1) 0013h 3 Timer1 (TF1) 001Bh 4 PCA (CF or CCFn) 0033h 5 UART (RI or TI) 0023h 6 Timer2 (TF2) 002Bh 7 ADC (ADCI) 0043h 8 SPI interrupt 0053h 9 113 4383A–8051–10/04 Registers Table 65. IEN0 Register IEN0 (S:A8h) Interrupt Enable Register 7 6 5 4 3 2 1 0 EA EC ET2 ES ET1 EX1 ET0 EX0 Bit Number Bit Mnemonic Description 7 EA Enable All Interrupt bit Clear to disable all interrupts. Set to enable all interrupts. If EA=1, each interrupt source is individually enabled or disabled by setting or clearing its interrupt enable bit. 6 EC PCA Interrupt Enable Clear to disable the PCA interrupt. Set to enable the PCA interrupt. 5 ET2 Timer 2 Overflow Interrupt Enable bit Clear to disable Timer 2 overflow interrupt. Set to enable Timer 2 overflow interrupt. 4 ES Serial Port Enable bit Clear to disable serial port interrupt. Set to enable serial port interrupt. 3 ET1 Timer 1 Overflow Interrupt Enable bit Clear to disable timer 1 overflow interrupt. Set to enable timer 1 overflow interrupt. 2 EX1 External Interrupt 1 Enable bit Clear to disable external interrupt 1. Set to enable external interrupt 1. 1 ET0 Timer 0 Overflow Interrupt Enable bit Clear to disable timer 0 overflow interrupt. Set to enable timer 0 overflow interrupt. 0 EX0 External Interrupt 0 Enable bit Clear to disable external interrupt 0. Set to enable external interrupt 0. Reset Value = 0000 0000b bit addressable 114 AT89C51AC3 4383A–8051–10/04 AT89C51AC3 Table 66. IEN1 Register IEN1 (S:E8h) Interrupt Enable Register 7 6 5 4 3 2 1 0 - - - - ESPI - EADC - Bit Number Bit Mnemonic Description 7 - Reserved The value read from this bit is indeterminate. Do not set this bit. 6 - Reserved The value read from this bit is indeterminate. Do not set this bit. 5 - Reserved The value read from this bit is indeterminate. Do not set this bit. 4 - Reserved The value read from this bit is indeterminate. Do not set this bit. 3 ESPI 2 - 1 EADC 0 - SPI Interrupt Enable bit Clear to disable the SPI interrupt. Set to enable the SPI interrupt. Reserved The value read from this bit is indeterminate. Do not set this bit. ADC Interrupt Enable bit Clear to disable the ADC interrupt. Set to enable the ADC interrupt. Reserved The value read from this bit is indeterminate. Do not set this bit. Reset Value = xxxx 0x0xb bit addressable 115 4383A–8051–10/04 Table 67. IPL0 Register IPL0 (S:B8h) Interrupt Enable Register 7 6 5 4 3 2 1 0 - PPC PT2 PS PT1 PX1 PT0 PX0 Bit Number Bit Mnemonic Description Reserved The value read from this bit is indeterminate. Do not set this bit. 7 - 6 PPC PCA Interrupt Priority bit Refer to PPCH for priority level 5 PT2 Timer 2 Overflow Interrupt Priority bit Refer to PT2H for priority level. 4 PS Serial Port Priority bit Refer to PSH for priority level. 3 PT1 Timer 1 Overflow Interrupt Priority bit Refer to PT1H for priority level. 2 PX1 External Interrupt 1 Priority bit Refer to PX1H for priority level. 1 PT0 Timer 0 Overflow Interrupt Priority bit Refer to PT0H for priority level. 0 PX0 External Interrupt 0 Priority bit Refer to PX0H for priority level. Reset Value = X000 0000b bit addressable 116 AT89C51AC3 4383A–8051–10/04 AT89C51AC3 Table 68. IPL1 Register IPL1 (S:F8h) Interrupt Priority Low Register 1 7 6 5 4 3 2 1 0 - - - - SPIL - PADCL - Bit Number Bit Mnemonic Description 7 - Reserved The value read from this bit is indeterminate. Do not set this bit. 6 - Reserved The value read from this bit is indeterminate. Do not set this bit. 5 - Reserved The value read from this bit is indeterminate. Do not set this bit. 4 - Reserved The value read from this bit is indeterminate. Do not set this bit. 3 SPIL 2 - 1 PADCL 0 - SPI Interrupt Priority Level Less Significant Bit Refer to SPIH for priority level. Reserved The value read from this bit is indeterminate. Do not set this bit. ADC Interrupt Priority Level Less Significant Bit Refer to PSPIH for priority level. Reserved The value read from this bit is indeterminate. Do not set this bit. Reset Value = XXXX 0X0Xb bit addressable 117 4383A–8051–10/04 Table 69. IPL0 Register IPH0 (B7h) Interrupt High Priority Register 7 6 5 4 3 2 1 0 - PPCH PT2H PSH PT1H PX1H PT0H PX0H Bit Number 7 6 5 4 3 2 1 0 Bit Mnemonic Description - Reserved The value read from this bit is indeterminate. Do not set this bit. PPCH PCA Interrupt Priority Level Most Significant bit Priority level PPCH PPC 0 0 Lowest 0 1 1 0 1 1 Highest priority PT2H Timer 2 Overflow Interrupt High Priority bit PT2H PT2 Priority Level 0 0 Lowest 0 1 1 0 1 1 Highest PSH Serial Port High Priority bit Priority Level PSH PS 0 0 Lowest 0 1 1 0 1 1 Highest PT1H Timer 1 Overflow Interrupt High Priority bit Priority Level PT1H PT1 0 0 Lowest 0 1 1 0 1 1 Highest PX1H External Interrupt 1 High Priority bit PX1H PX1 Priority Level 0 0 Lowest 0 1 1 0 1 1 Highest PT0H Timer 0 Overflow Interrupt High Priority bit Priority Level PT0H PT0 0 0 Lowest 0 1 1 0 1 1 Highest PX0H External Interrupt 0 high priority bit Priority Level PX0H PX0 0 0 Lowest 0 1 1 0 1 1 Highest Reset Value = X000 0000b 118 AT89C51AC3 4383A–8051–10/04 AT89C51AC3 Table 70. IPH1 Register IPH1 (S:F7h) Interrupt High Priority Register 1 7 6 5 4 3 2 1 0 - - - - SPIH - PADCH - Bit Number Bit Mnemonic Description 7 - Reserved The value read from this bit is indeterminate. Do not set this bit. 6 - Reserved The value read from this bit is indeterminate. Do not set this bit. 5 - Reserved The value read from this bit is indeterminate. Do not set this bit. 4 - Reserved The value read from this bit is indeterminate. Do not set this bit. 3 SPIH 2 - 1 PADCH 0 - SPI Interrupt Priority Level Most Significant bit SPIH SPIL Priority level 0 0 Lowest 0 1 1 0 1 1 Highest Reserved The value read from this bit is indeterminate. Do not set this bit. ADC Interrupt Priority Level Most Significant bit PADCH PADCL Priority level 0 0 Lowest 0 1 1 0 1 1 Highest Reserved The value read from this bit is indeterminate. Do not set this bit. Reset Value = XXXX 0X0Xb 119 4383A–8051–10/04 Electrical Characteristics Absolute Maximum Ratings Note: Ambiant Temperature Under Bias: I = industrial ....................................................... -40°C to 85°C Storage Temperature .................................... -65°C to + 150°C Voltage on VCC from VSS ......................................-0.5V to + 6V Voltage on Any Pin from VSS ..................... -0.5V to VCC + 0.2V Stresses at or above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions may affect device reliability. The power dissipation is based on the maximum allowable die temperature and the thermal resistance of the package. Power Dissipation .............................................................. 1 W DC Parameters for Standard Voltage TA = -40°C to +85°C; VSS = 0V; VCC =2.7V to 5.5V and F = 0 to 40 MHz (both internal and external code execution) VCC =4.5V to 5.5V and F = 0 to 60 MHz (internal code execution only) Table 71. DC Parameters in Standard Voltage Symbol Parameter Min VIL Input Low Voltage VIH Input High Voltage except XTAL1, RST VIH1 Input High Voltage, XTAL1, RST VOL VOL1 VOH VOH1 RRST 120 Output Low Voltage, ports 1, 2, 3 and 4 Typ(5) Max Unit -0.5 0.2Vcc - 0.1 V 0.2 VCC + 0.9 VCC + 0.5 V 0.7 VCC VCC + 0.5 V 0.3 V IOL = 100 µA(4) 0.45 V IOL = 1.6 mA(4) 1.0 V IOL = 3.5 mA(4) 0.3 V IOL = 200 µA(4) 0.45 V IOL = 3.2 mA(4) 1.0 V IOL = 7.0 mA(4) (6) Output Low Voltage, port 0, ALE, PSEN (6) Output High Voltage, ports 1, 2, 3, and 4 Output High Voltage, port 0, ALE, PSEN RST Pulldown Resistor VCC - 0.3 V VCC - 0.7 V VCC - 1.5 V VCC - 0.3 V VCC - 0.7 V VCC - 1.5 V 50 100 200 kΩ Test Conditions IOH = -10 µA IOH = -30 µA IOH = -60 µA VCC = 3V to 5.5V IOH = -200 µA IOH = -3.2 mA IOH = -7.0 mA VCC = 5V ± 10% IIL Logical 0 Input Current ports 1, 2, 3 and 4 -50 µA Vin = 0.45V ILI Input Leakage Current ±10 µA 0.45V < Vin < VCC ITL Logical 1 to 0 Transition Current, ports 1, 2, 3 and 4 -650 µA Vin = 2.0V CIO Capacitance of I/O Buffer 10 pF Fc = 1 MHz TA = 25°C IPD Power-down Current 150 µA 3V < VCC < 5.5V(3) 75 AT89C51AC3 4383A–8051–10/04 AT89C51AC3 Table 71. DC Parameters in Standard Voltage (Continued) Symbol ICC Notes: Parameter Power Supply Current Typ(5) Min ICCOP = 0.4 Frequency (MHz) + 8 ICCIDLE = 0.2 Frequency (MHz) + 8 Max Unit mA Test Conditions Vcc = 5.5V(1)(2) 1. Operating ICC is measured with all output pins disconnected; XTAL1 driven with TCLCH, TCHCL = 5 ns (see Figure 67.), VIL = VSS + 0.5V, VIH = VCC - 0.5V; XTAL2 N.C.; EA = RST = Port 0 = VCC. ICC would be slightly higher if a crystal oscillator used (see Figure 64.). 2. Idle ICC is measured with all output pins disconnected; XTAL1 driven with TCLCH, TCHCL = 5 ns, VIL = VSS + 0.5V, VIH = VCC 0.5V; XTAL2 N.C; Port 0 = VCC; EA = RST = VSS (see Figure 65.). 3. Power-down ICC is measured with all output pins disconnected; EA = VCC, PORT 0 = VCC; XTAL2 NC.; RST = VSS (see Figure 66.). In addition, the WDT must be inactive and the POF flag must be set. 4. Capacitance loading on Ports 0 and 2 may cause spurious noise pulses to be superimposed on the VOLs of ALE and Ports 1 and 3. The noise is due to external bus capacitance discharging into the Port 0 and Port 2 pins when these pins make 1 to 0 transitions during bus operation. In the worst cases (capacitive loading 100pF), the noise pulse on the ALE line may exceed 0.45V with maxi VOL peak 0.6V. A Schmitt Trigger use is not necessary. 5. Typicals are based on a limited number of samples and are not guaranteed. The values listed are at room temperature. 6. Under steady state (non-transient) conditions, IOL must be externally limited as follows: Maximum IOL per port pin: 10 mA Maximum IOL per 8-bit port: Port 0: 26 mA Ports 1, 2, 3 and 4: 15 mA Maximum total IOL for all output pins: 71 mA If IOL exceeds the test condition, VOL may exceed the related specification. Pins are not guaranteed to sink current greater than the listed test conditions. Figure 64. ICC Test Condition, Active Mode VCC ICC VCC P0 VCC RST (NC) CLOCK SIGNAL VCC EA XTAL2 XTAL1 VSS All other pins are disconnected. 121 4383A–8051–10/04 Figure 65. ICC Test Condition, Idle Mode VCC ICC VCC VCC P0 RST EA XTAL2 XTAL1 VSS (NC) CLOCK SIGNAL All other pins are disconnected. Figure 66. ICC Test Condition, Power-Down Mode VCC ICC VCC VCC P0 RST (NC) EA XTAL2 XTAL1 All other pins are disconnected. VSS Figure 67. Clock Signal Waveform for ICC Tests in Active and Idle Modes VCC-0.5V 0.45V TCLCH TCHCL TCLCH = TCHCL = 5ns. DC Parameters for A/D Converter Table 72. DC Parameters for AD Converter in Precision Conversion Symbol Parameter AVin Analog input voltage Rref Resistance between Vref and Vss Vref Reference voltage Cai Analog input Capacitance Rai Analog input Resistor INL Integral non linearity DNL Differential non linearity OE Note: 122 0.7VCC 0.2VCC-0.1 Offset error Min Typ(1) Vss- 0.2 12 16 2.40 Max Unit Vref + 0.2 V 24 kΩ 3.00 V 60 -2 Test Conditions pF During sampling 400 Ω During sampling 1 2 lsb 0.5 1 lsb 2 lsb 1. Typicals are based on a limited number of samples and are not guaranteed. AT89C51AC3 4383A–8051–10/04 AT89C51AC3 AC Parameters Explanation of the AC Symbols Each timing symbol has 5 characters. The first character is always a “T” (stands for time). The other characters, depending on their positions, stand for the name of a signal or the logical status of that signal. The following is a list of all the characters and what they stand for. Example: TAVLL = Time for Address Valid to ALE Low. TLLPL = Time for ALE Low to PSEN Low. TA = -40°C to +85°C; VSS = 0V; VCC = 3V to 5.5V; F = 0 to 40 MHz. (Load Capacitance for port 0, ALE and PSEN = 60 pF; Load Capacitance for all other outputs = 60 pF.) Table 73, Table 76 and Table 79 give the description of each AC symbols. Table 74, Table 78 and Table 80 give for each range the AC parameter. Table 75, Table 78 and Table 81 give the frequency derating formula of the AC parameter for each speed range description. To calculate each AC symbols: Take the x value and use this value in the formula. Example: TLLIV and 20 MHz, Standard clock. x = 30 ns T = 50 ns TCCIV = 4T - x = 170 ns 123 4383A–8051–10/04 External Program Memory Characteristics Table 73. Symbol Description Symbol T Parameter Oscillator clock period TLHLL ALE pulse width TAVLL Address Valid to ALE TLLAX Address Hold After ALE TLLIV ALE to Valid Instruction In TLLPL ALE to PSEN TPLPH PSEN Pulse Width TPLIV PSEN to Valid Instruction In TPXIX Input Instruction Hold After PSEN TPXIZ Input Instruction Float After PSEN TAVIV Address to Valid Instruction In TPLAZ PSEN Low to Address Float Table 74. AC Parameters for a Fix Clock (F = 40 MHz) Symbol Min T 25 ns TLHLL 40 ns TAVLL 10 ns TLLAX 10 ns TLLIV 70 Units ns TLLPL 15 ns TPLPH 55 ns TPLIV TPXIX 124 Max 35 0 ns ns TPXIZ 18 ns TAVIV 85 ns TPLAZ 10 ns AT89C51AC3 4383A–8051–10/04 AT89C51AC3 Table 75. AC Parameters for a Variable Clock Symbol Type Standard Clock X2 Clock X parameter Units TLHLL Min 2T-x T-x 10 ns TAVLL Min T-x 0.5 T - x 15 ns TLLAX Min T-x 0.5 T - x 15 ns TLLIV Max 4T-x 2T-x 30 ns TLLPL Min T-x 0.5 T - x 10 ns TPLPH Min 3T-x 1.5 T - x 20 ns TPLIV Max 3T-x 1.5 T - x 40 ns TPXIX Min x x 0 ns TPXIZ Max T-x 0.5 T - x 7 ns TAVIV Max 5T-x 2.5 T - x 40 ns TPLAZ Max x x 10 ns External Program Memory Read Cycle 12 TCLCL TLHLL TLLIV ALE TLLPL TPLPH PSEN TLLAX TAVLL PORT 0 INSTR IN TPLIV TPLAZ A0-A7 TPXAV TPXIZ TPXIX INSTR IN A0-A7 INSTR IN TAVIV PORT 2 ADDRESS OR SFR-P2 ADDRESS A8-A15 ADDRESS A8-A15 125 4383A–8051–10/04 External Data Memory Characteristics Table 76. Symbol Description Symbol Parameter TRLRH RD Pulse Width TWLWH WR Pulse Width TRLDV RD to Valid Data In TRHDX Data Hold After RD TRHDZ Data Float After RD TLLDV ALE to Valid Data In TAVDV Address to Valid Data In TLLWL ALE to WR or RD TAVWL Address to WR or RD TQVWX Data Valid to WR Transition TQVWH Data set-up to WR High TWHQX Data Hold After WR TRLAZ RD Low to Address Float TWHLH RD or WR High to ALE high Table 77. AC Parameters for a Variable Clock (F=40MHz) Symbol Min TRLRH 130 ns TWLWH 130 ns TRLDV TRHDX 100 0 Units ns ns TRHDZ 30 ns TLLDV 160 ns TAVDV 165 ns 100 ns TLLWL 50 TAVWL 75 ns TQVWX 10 ns TQVWH 160 ns TWHQX 15 ns TRLAZ TWHLH 126 Max 10 0 ns 40 ns AT89C51AC3 4383A–8051–10/04 AT89C51AC3 Table 78. AC Parameters for a Variable Clock Symbol Type Standard Clock X2 Clock X parameter Units TRLRH Min 6T-x 3T-x 20 ns TWLWH Min 6T-x 3T-x 20 ns TRLDV Max 5T-x 2.5 T - x 25 ns TRHDX Min x x 0 ns TRHDZ Max 2T-x T-x 20 ns TLLDV Max 8T-x 4T -x 40 ns TAVDV Max 9T-x 4.5 T - x 60 ns TLLWL Min 3T-x 1.5 T - x 25 ns TLLWL Max 3T+x 1.5 T + x 25 ns TAVWL Min 4T-x 2T-x 25 ns TQVWX Min T-x 0.5 T - x 15 ns TQVWH Min 7T-x 3.5 T - x 25 ns TWHQX Min T-x 0.5 T - x 10 ns TRLAZ Max x x 0 ns TWHLH Min T-x 0.5 T - x 15 ns TWHLH Max T+x 0.5 T + x 15 ns 127 4383A–8051–10/04 External Data Memory Write Cycle TWHLH ALE PSEN TLLWL TWLWH WR TQVWX TLLAX PORT 0 A0-A7 TWHQX TQVWH DATA OUT TAVWL PORT 2 ADDRESS OR SFR-P2 ADDRESS A8-A15 OR SFR P2 External Data Memory Read Cycle TWHLH TLLDV ALE PSEN TLLWL TRLRH RD TRHDZ TAVDV TLLAX PORT 0 TAVWL PORT 2 TRHDX A0-A7 ADDRESS OR SFR-P2 DATA IN TRLAZ ADDRESS A8-A15 OR SFR P2 Serial Port Timing – Shift Register Mode Table 79. Symbol Description (F = 40 MHz) 128 Symbol Parameter TXLXL Serial port clock cycle time TQVHX Output data set-up to clock rising edge TXHQX Output data hold after clock rising edge TXHDX Input data hold after clock rising edge TXHDV Clock rising edge to input data valid AT89C51AC3 4383A–8051–10/04 AT89C51AC3 Table 80. AC Parameters for a Fix Clock (F = 40 MHz) Symbol Min Max TXLXL 300 ns TQVHX 200 ns TXHQX 30 ns TXHDX 0 ns TXHDV Units 117 ns Table 81. AC Parameters for a Variable Clock Symbol Type Standard Clock X2 Clock X parameter for -M range TXLXL Min 12 T 6T TQVHX Min 10 T - x 5T-x 50 ns TXHQX Min 2T-x T-x 20 ns TXHDX Min x x 0 ns TXHDV Max 10 T - x 5 T- x 133 ns Units ns Shift Register Timing Waveforms 0 INSTRUCTION 1 2 3 4 5 6 7 8 ALE TXLXL CLOCK TXHQX TQVXH 0 OUTPUT DATA WRITE to SBUF 1 2 4 5 6 TXHDX TXHDV INPUT DATA 3 VALID VALID VALID SET TI VALID VALID VALID VALID VALID SET RI CLEAR RI External Clock Drive Characteristics (XTAL1) 7 Table 82. AC Parameters Symbol Parameter Min Max Units TCLCL Oscillator Period 25 ns TCHCX High Time 5 ns TCLCX Low Time 5 ns TCLCH Rise Time 5 ns TCHCL Fall Time 5 ns 60 % TCHCX/TCLCX Cyclic ratio in X2 mode 40 129 4383A–8051–10/04 External Clock Drive Waveforms VCC-0.5V 0.45V 0.7VCC 0.2VCC-0.1 TCHCX TCLCH TCLCX TCHCL TCLCL AC Testing Input/Output Waveforms VCC -0.5V 0.2 VCC + 0.9 INPUT/OUTPUT 0.2 VCC - 0.1 0.45V AC inputs during testing are driven at VCC - 0.5 for a logic “1” and 0.45V for a logic “0”. Timing measurement are made at VIH min for a logic “1” and VIL max for a logic “0”. Float Waveforms FLOAT VOH - 0.1 V VOL + 0.1 V VLOAD VLOAD + 0.1 V VLOAD - 0.1 V For timing purposes as port pin is no longer floating when a 100 mV change from load voltage occurs and begins to float when a 100 mV change from the loaded VOH/VOL level occurs. IOL/IOH ≥ ± 20 mA. 130 AT89C51AC3 4383A–8051–10/04 AT89C51AC3 Clock Waveforms Valid in normal clock mode. In X2 mode XTAL2 must be changed to XTAL2/2. INTERNAL CLOCK STATE4 STATE5 STATE6 STATE1 STATE2 STATE3 STATE4 STATE5 P1 P1 P1 P1 P1 P1 P1 P1 P2 P2 P2 P2 P2 P2 P2 P2 XTAL2 ALE THESE SIGNALS ARE NOT ACTIVATED DURING THE EXECUTION OF A MOVX INSTRUCTION EXTERNAL PROGRAM MEMORY FETCH PSEN P0 DATA SAMPLED PCL OUT DATA SAMPLED FLOAT P2 (EXT) PCL OUT FLOAT DATA SAMPLED PCL OUT FLOAT INDICATES ADDRESS TRANSITIONS READ CYCLE RD PCL OUT (IF PROGRAM MEMORY IS EXTERNAL) P0 DPL OR Rt OUT DATA SAMPLED FLOAT INDICATES DPH OR P2 SFR TO PCH TRANSITION P2 WRITE CYCLE WR P0 PCL OUT (EVEN IF PROGRAM MEMORY IS INTERNAL) DPL OR Rt OUT PCL OUT (IF PROGRAM MEMORY IS EXTERNAL) DATA OUT INDICATES DPH OR P2 SFR TO PCH TRANSITION P2 PORT OPERATION OLD DATA NEW DATA MOV PORT SRC P0 PINS SAMPLED P0 PINS SAMPLED MOV DEST P0 MOV DEST PORT (P1. P2. P3) (INCLUDES INTO. INT1. TO T1) SERIAL PORT SHIFT CLOCK P1, P2, P3 PINS SAMPLED RXD SAMPLED P1, P2, P3 PINS SAMPLED RXD SAMPLED TXD (MODE 0) This diagram indicates when signals are clocked internally. The time it takes the signals to propagate to the pins, however, ranges from 25 to 125 ns. This propagation delay is dependent on variables such as temperature and pin loading. Propagation also varies from output to output and component. Typically though (TA=25°C fully loaded) RD and WR propagation delays are approximately 50ns. The other signals are typically 85 ns. Propagation delays are incorporated in the AC specifications. 131 4383A–8051–10/04 Flash Memory Table 83. Timing Symbol Definitions Signals Conditions S (Hardware condition) PSEN#,EA L Low R RST V Valid B FBUSY flag X No Longer Valid Table 84. Memory AC Timing VDD = 3V to 5.5V, TA = -40 to +85°C Symbol Parameter Min Typ Max TSVRL Input PSEN# Valid to RST Edge 50 ns TRLSX Input PSEN# Hold after RST Edge 50 ns TBHBL Flash Internal Busy (Programming) Time 10 ms Figure 68. Flash Memory – ISP Waveforms RST TSVRL TRLSX PSEN#1 Figure 69. Flash Memory – Internal Busy Waveforms FBUSY bit 132 Unit TBHBL AT89C51AC3 4383A–8051–10/04 AT89C51AC3 Ordering Information Table 85. Possible Order Entries Part Number Boot Loader Temperature Range Package Packing Product Marking AT89C51AC3-RLTIM UART Industrial VQFP44 Tray AT89C51AC3-IM AT89C51AC3-SLSIM UART Industrial PLCC44 Stick AT89C51AC3-IM AT89C51AC3-RDTIM UART Industrial VQFP64 Tray AT89C51AC3-IM AT89C51AC3-S3SIM UART Industrial PLCC52 Stick AT89C51AC3-IM 133 4383A–8051–10/04 Package Drawing VQFP44 134 AT89C51AC3 4383A–8051–10/04 AT89C51AC3 PLCC44 135 4383A–8051–10/04 VQFP64 136 AT89C51AC3 4383A–8051–10/04 AT89C51AC3 PLCC52 137 4383A–8051–10/04 AT89C51AC3 Features................................................................................................ 1 Description ........................................................................................... 1 Block Diagram...................................................................................... 2 Pin Configuration................................................................................. 3 I/O Configurations................................................................................................. 7 Port 1, Port 3 and Port 4 ....................................................................................... 7 Port 0 and Port 2................................................................................................... 8 Read-Modify-Write Instructions ............................................................................ 9 Quasi-Bidirectional Port Operation ..................................................................... 10 SFR Mapping...................................................................................... 11 Clock ................................................................................................... 15 Description.......................................................................................................... 15 Registers............................................................................................................. 18 Data Memory ...................................................................................... 20 Internal Space..................................................................................................... External Space ................................................................................................... Dual Data Pointer ............................................................................................... Registers............................................................................................................. 21 22 24 25 Power Monitor.................................................................................... 27 Description.......................................................................................................... 27 Reset ................................................................................................... 29 Introduction ......................................................................................................... 29 Reset Input ......................................................................................................... 29 Reset Output........................................................................................................ 30 Power Management ........................................................................... 31 Introduction ......................................................................................................... Idle Mode ............................................................................................................ Power-Down Mode ............................................................................................. Registers............................................................................................................. 31 31 31 34 EEPROM Data Memory...................................................................... 35 Write Data in the Column Latches ...................................................................... Programming ...................................................................................................... Read Data........................................................................................................... Examples ............................................................................................................ Registers............................................................................................................. 35 35 35 36 37 1 4383A–8051–10/04 Program/Code Memory ..................................................................... 38 Flash Memory Architecture................................................................................. 40 Overview of FM0 Operations .............................................................................. 44 Operation Cross Memory Access .................................................... 53 Sharing Instructions.......................................................................... 54 In-System Programming (ISP) .......................................................... 56 Flash Programming and Erasure........................................................................ Boot Process ...................................................................................................... Application Programming Interface..................................................................... XROW Bytes....................................................................................................... Hardware Security Byte ...................................................................................... 56 56 58 58 59 Serial I/O Port .................................................................................... 60 Framing Error Detection .................................................................................... Automatic Address Recognition.......................................................................... Given Address ................................................................................................... Broadcast Address ............................................................................................ Registers............................................................................................................. 60 61 62 62 63 Timers/Counters ................................................................................ 66 Timer/Counter Operations .................................................................................. Timer 0................................................................................................................ Timr 1.................................................................................................................. Interrupt .............................................................................................................. Registers............................................................................................................. 66 66 69 70 70 Timer 2 ................................................................................................ 74 Auto-Reload Mode............................................................................................. 74 Programmable Clock-Output .............................................................................. 75 Registers............................................................................................................. 76 Watchdog Timer................................................................................. 79 Watchdog Programming ..................................................................................... 80 Watchdog Timer During Power-down Mode and Idle ......................................... 81 Serial Port Interface (SPI).................................................................. 83 Features.............................................................................................................. 83 Signal Description............................................................................................... 83 Functional Description ........................................................................................ 85 Programmable Counter Array (PCA) ............................................... 94 PCA Timer .......................................................................................................... 94 PCA Modules...................................................................................................... 95 2 AT89C51AC3 4383A–8051–10/04 AT89C51AC3 PCA Interrupt ...................................................................................................... 96 PCA Capture Mode............................................................................................. 96 16-bit Software Timer Mode ............................................................................... 97 High Speed Output Mode ................................................................................... 98 Pulse Width Modulator Mode.............................................................................. 98 PCA WatchDog Timer ........................................................................................ 99 PCA Registers .................................................................................................. 100 Analog-to-Digital Converter (ADC)................................................. 105 Features............................................................................................................ ADC Port1 I/O Functions .................................................................................. ADC Converter Operation................................................................................. Voltage Conversion .......................................................................................... Clock Selection ................................................................................................. ADC Standby Mode .......................................................................................... IT ADC Management ........................................................................................ Routines examples ........................................................................................... Registers........................................................................................................... 105 105 107 107 107 107 108 108 109 Interrupt System .............................................................................. 112 Introduction ....................................................................................................... 112 Registers........................................................................................................... 114 Electrical Characteristics................................................................ 120 Absolute Maximum Ratings ..............................................................................120 DC Parameters for Standard Voltage ................................................................ 120 DC Parameters for A/D Converter .................................................................... 122 AC Parameters ..................................................................................................123 Ordering Information....................................................................... 133 Package Drawing ............................................................................. 134 CA-BGA ............................................................................................................ VQFP44 ............................................................................................................ PLCC44 ............................................................................................................ VQFP64 ............................................................................................................ PLCC52 ............................................................................................................ 134 135 136 137 138 3 4383A–8051–10/04 Atmel Corporation 2325 Orchard Parkway San Jose, CA 95131 Tel: 1(408) 441-0311 Fax: 1(408) 487-2600 Regional Headquarters Europe Atmel Sarl Route des Arsenaux 41 Case Postale 80 CH-1705 Fribourg Switzerland Tel: (41) 26-426-5555 Fax: (41) 26-426-5500 Asia Room 1219 Chinachem Golden Plaza 77 Mody Road Tsimshatsui East Kowloon Hong Kong Tel: (852) 2721-9778 Fax: (852) 2722-1369 Japan 9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Japan Tel: (81) 3-3523-3551 Fax: (81) 3-3523-7581 Atmel Operations Memory 2325 Orchard Parkway San Jose, CA 95131 Tel: 1(408) 441-0311 Fax: 1(408) 436-4314 RF/Automotive Theresienstrasse 2 Postfach 3535 74025 Heilbronn, Germany Tel: (49) 71-31-67-0 Fax: (49) 71-31-67-2340 Microcontrollers 2325 Orchard Parkway San Jose, CA 95131 Tel: 1(408) 441-0311 Fax: 1(408) 436-4314 La Chantrerie BP 70602 44306 Nantes Cedex 3, France Tel: (33) 2-40-18-18-18 Fax: (33) 2-40-18-19-60 ASIC/ASSP/Smart Cards 1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 Tel: 1(719) 576-3300 Fax: 1(719) 540-1759 Biometrics/Imaging/Hi-Rel MPU/ High Speed Converters/RF Datacom Avenue de Rochepleine BP 123 38521 Saint-Egreve Cedex, France Tel: (33) 4-76-58-30-00 Fax: (33) 4-76-58-34-80 Zone Industrielle 13106 Rousset Cedex, France Tel: (33) 4-42-53-60-00 Fax: (33) 4-42-53-60-01 1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 Tel: 1(719) 576-3300 Fax: 1(719) 540-1759 Scottish Enterprise Technology Park Maxwell Building East Kilbride G75 0QR, Scotland Tel: (44) 1355-803-000 Fax: (44) 1355-242-743 e-mail [email protected] Web Site http://www.atmel.com Disclaimer: Atmel Corporation makes no warranty for the use of its products, other than those expressly contained in the Company’s standard warranty which is detailed in Atmel’s Terms and Conditions located on the Company’s web site. The Company assumes no responsibility for any errors which may appear in this document, reserves the right to change devices or specifications detailed herein at any time without notice, and does not make any commitment to update the information contained herein. No licenses to patents or other intellectual property of Atmel are granted by the Company in connection with the sale of Atmel products, expressly or by implication. Atmel’s products are not authorized for use as critical components in life support devices or systems. © Atmel Corporation 2004. All rights reserved. Atmel ® and combinations thereof, are the trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be the trademarks of others. Printed on recycled paper. 4383A–8051–10/04 /xM