BC847CDXV6T1, BC847CDXV6T5 BC848CDXV6T1, BC848CDXV6T5 Dual General Purpose Transistors http://onsemi.com NPN Duals (3) These transistors are designed for general purpose amplifier applications. They are housed in the SOT-563 which is designed for low power surface mount applications. • Lead-Free Solder Plating (2) Q1 Q2 (4) MAXIMUM RATINGS Rating Symbol BC847 BC848 Unit Collector - Emitter Voltage VCEO 45 30 V Collector - Base Voltage VCBO 50 30 V Emitter - Base Voltage VEBO 6.0 5.0 V IC 100 100 mAdc Collector Current Continuous (5) Total Device Dissipation TA = 25°C 6 Characteristic (Both Junctions Heated) Total Device Dissipation TA = 25°C Symbol Max Unit PD 357 (Note 1) 2.9 (Note 1) mW 3 MARKING DIAGRAMS 1G D 1L D mW/°C RJA 350 (Note 1) °C/W Symbol Max Unit PD 500 (Note 1) 4.0 (Note 1) mW mW/°C Thermal Resistance Junction-to-Ambient RJA 250 (Note 1) °C/W Junction and Storage Temperature Range TJ, Tstg - 55 to +150 °C 1. FR-4 @ Minimum Pad March, 2003 - Rev. 0 2 SOT-563 CASE 463A PLASTIC Derate above 25°C Semiconductor Components Industries, LLC, 2003 54 1 Derate above 25°C Thermal Resistance Junction-to-Ambient (6) BC847CDXV6T1 THERMAL CHARACTERISTICS Characteristic (One Junction Heated) (1) 1 1G = BC847CDXV6T1, BC847CDXV6T5 1L = BC848CDXV6T1, BC848CDXV6T5 D = Date Code ORDERING INFORMATION Device Package Shipping BC847CDXV6T1 SOT-563 4 mm pitch 4000/Tape & Reel BC847CDXV6T5 SOT-563 2 mm pitch 8000/Tape & Reel BC848CDXV6T1 SOT-563 4 mm pitch 4000/Tape & Reel BC848CDXV6T5 SOT-563 2 mm pitch 8000/Tape & Reel Publication Order Number: BC847CDXV6T1/D BC847CDXV6T1, BC847CDXV6T5 BC848CDXV6T1, BC848CDXV6T5 ELECTRICAL CHARACTERISTICS (TA = 25°C unless otherwise noted) Characteristic Symbol Min Typ Max 45 30 - - 50 30 - - 50 30 - - 6.0 5.0 - - - - 15 5.0 420 270 520 800 Unit OFF CHARACTERISTICS Collector - Emitter Breakdown Voltage (IC = 10 mA) Collector - Emitter Breakdown Voltage (IC = 10 µA, VEB = 0) Collector - Base Breakdown Voltage (IC = 10 A) Emitter - Base Breakdown Voltage (IE = 1.0 A) V(BR)CEO BC847CDXV6T1 BC848CDXV6T1 V V(BR)CES BC847CDXV6T1 BC848CDXV6T1 V V(BR)CBO BC847CDXV6T1 BC848CDXV6T1 V V(BR)EBO BC847CDXV6T1 BC848CDXV6T1 Collector Cutoff Current (VCB = 30 V) (VCB = 30 V, TA = 150°C) ICBO V nA µA ON CHARACTERISTICS DC Current Gain (IC = 10 µA, VCE = 5.0 V) (IC = 2.0 mA, VCE = 5.0 V) hFE - Collector - Emitter Saturation Voltage (IC = 10 mA, IB = 0.5 mA) Collector - Emitter Saturation Voltage (IC = 100 mA, IB = 5.0 mA) VCE(sat) - - 0.25 0.6 V Base - Emitter Saturation Voltage (IC = 10 mA, IB = 0.5 mA) Base - Emitter Saturation Voltage (IC = 100 mA, IB = 5.0 mA) VBE(sat) - 0.7 0.9 - V Base - Emitter Voltage (IC = 2.0 mA, VCE = 5.0 V) Base - Emitter Voltage (IC = 10 mA, VCE = 5.0 V) VBE(on) 580 - 660 - 700 770 mV fT 100 - - MHz Cobo - - 4.5 pF - - 10 SMALL- SIGNAL CHARACTERISTICS Current - Gain - Bandwidth Product (IC = 10 mA, VCE = 5.0 Vdc, f = 100 MHz) Output Capacitance (VCB = 10 V, f = 1.0 MHz) Noise Figure (IC = 0.2 mA, VCE = 5.0 Vdc, RS = 2.0 kΩ,f = 1.0 kHz, BW = 200 Hz) http://onsemi.com 2 NF dB BC847CDXV6T1, BC847CDXV6T5 BC848CDXV6T1, BC848CDXV6T5 TYPICAL CHARACTERISTICS 1.0 VCE = 10 V TA = 25°C 1.5 TA = 25°C 0.9 0.8 V, VOLTAGE (VOLTS) hFE , NORMALIZED DC CURRENT GAIN 2.0 1.0 0.8 0.6 0.4 VBE(sat) @ IC/IB = 10 0.7 VBE(on) @ VCE = 10 V 0.6 0.5 0.4 0.3 0.2 0.3 VCE(sat) @ IC/IB = 10 0.1 0.2 0.2 0.5 50 2.0 5.0 10 1.0 20 IC, COLLECTOR CURRENT (mAdc) 100 0 0.1 200 2.0 TA = 25°C 1.6 IC = 200 mA 1.2 IC = IC = 10 mA 20 mA IC = 50 mA IC = 100 mA 0.8 0.4 0 0.02 10 0.1 1.0 IB, BASE CURRENT (mA) 20 1.0 −55°C to +125°C 1.2 1.6 2.0 2.4 2.8 f, T CURRENT−GAIN − BANDWIDTH PRODUCT (MHz) C, CAPACITANCE (pF) TA = 25°C Cib 3.0 Cob 2.0 1.0 0.4 0.6 0.8 1.0 2.0 4.0 6.0 8.0 10 VR, REVERSE VOLTAGE (VOLTS) 20 100 Figure 4. Base-Emitter Temperature Coefficient 10 5.0 10 1.0 IC, COLLECTOR CURRENT (mA) 0.2 Figure 3. Collector Saturation Region 7.0 50 70 100 Figure 2. “Saturation” and “On” Voltages θVB, TEMPERATURE COEFFICIENT (mV/ °C) VCE , COLLECTOR−EMITTER VOLTAGE (V) Figure 1. Normalized DC Current Gain 0.2 0.3 0.5 0.7 1.0 2.0 3.0 5.0 7.0 10 20 30 IC, COLLECTOR CURRENT (mAdc) 40 400 300 200 VCE = 10 V TA = 25°C 100 80 60 40 30 20 0.5 0.7 Figure 5. Capacitances 1.0 2.0 3.0 5.0 7.0 10 20 IC, COLLECTOR CURRENT (mAdc) 30 Figure 6. Current-Gain - Bandwidth Product http://onsemi.com 3 50 BC847CDXV6T1, BC847CDXV6T5 BC848CDXV6T1, BC848CDXV6T5 INFORMATION FOR USING THE SOT-563 SURFACE MOUNT PACKAGE MINIMUM RECOMMENDED FOOTPRINT FOR SURFACE MOUNTED APPLICATIONS Surface mount board layout is a critical portion of the total design. The footprint for the semiconductor packages must be the correct size to insure proper solder connection interface between the board and the package. With the correct pad geometry, the packages will self align when subjected to a solder reflow process. 0.3 0.45 1.0 1.35 0.5 0.5 Dimensions in mm SOT-563 SOT-563 POWER DISSIPATION SOLDERING PRECAUTIONS The power dissipation of the SOT-563 is a function of the pad size. This can vary from the minimum pad size for soldering to a pad size given for maximum power dissipation. Power dissipation for a surface mount device is determined by TJ(max), the maximum rated junction temperature of the die, RθJA, the thermal resistance from the device junction to ambient, and the operating temperature, TA. Using the values provided on the data sheet for the SOT-563 package, PD can be calculated as follows: PD = The melting temperature of solder is higher than the rated temperature of the device. When the entire device is heated to a high temperature, failure to complete soldering within a short time could result in device failure. Therefore, the following items should always be observed in order to minimize the thermal stress to which the devices are subjected. • Always preheat the device. • The delta temperature between the preheat and soldering should be 100°C or less.* • When preheating and soldering, the temperature of the leads and the case must not exceed the maximum temperature ratings as shown on the data sheet. When using infrared heating with the reflow soldering method, the difference shall be a maximum of 10°C. • The soldering temperature and time shall not exceed 260°C for more than 10 seconds. • When shifting from preheating to soldering, the maximum temperature gradient shall be 5°C or less. • After soldering has been completed, the device should be allowed to cool naturally for at least three minutes. Gradual cooling should be used as the use of forced cooling will increase the temperature gradient and result in latent failure due to mechanical stress. • Mechanical stress or shock should not be applied during cooling. TJ(max) - TA RθJA The values for the equation are found in the maximum ratings table on the data sheet. Substituting these values into the equation for an ambient temperature TA of 25°C, one can calculate the power dissipation of the device which in this case is 150 milliwatts. PD = 150°C - 25°C 833°C/W = 150 milliwatts The 833°C/W for the SOT-563 package assumes the use of the recommended footprint on a glass epoxy printed circuit board to achieve a power dissipation of 150 milliwatts. There are other alternatives to achieving higher power dissipation from the SOT-563 package. Another alternative would be to use a ceramic substrate or an aluminum core board such as Thermal Clad. Using a board material such as Thermal Clad, an aluminum core board, the power dissipation can be doubled using the same footprint. * Soldering a device without preheating can cause excessive thermal shock and stress which can result in damage to the device http://onsemi.com 4 BC847CDXV6T1, BC847CDXV6T5 BC848CDXV6T1, BC848CDXV6T5 PACKAGE DIMENSIONS SOT-563, 6 LEAD CASE 463A-01 ISSUE O A -X- 5 6 1 2 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETERS 3. MAXIMUM LEAD THICKNESS INCLUDES LEAD FINISH THICKNESS. MINIMUM LEAD THICKNESS IS THE MINIMUM THICKNESS OF BASE MATERIAL. C K 4 B -Y- 3 D G STYLE 1: PIN 1. 2. 3. 4. 5. 6. J 5 PL 6 0.08 (0.003) EMITTER 1 BASE 1 COLLECTOR 2 EMITTER 2 BASE 2 COLLECTOR 1 DIM A B C D G J K S S M X Y STYLE 2: PIN 1. 2. 3. 4. 5. 6. STYLE 3: PIN 1. 2. 3. 4. 5. 6. EMITTER 1 EMITTER2 BASE 2 COLLECTOR 2 BASE 1 COLLECTOR 1 CATHODE 1 CATHODE 1 ANODE/ANODE 2 CATHODE 2 CATHODE 2 ANODE/ANODE 1 http://onsemi.com 5 STYLE 4: PIN 1. 2. 3. 4. 5. 6. MILLIMETERS MIN MAX 1.50 1.70 1.10 1.30 0.50 0.60 0.17 0.27 0.50 BSC 0.08 0.18 0.10 0.30 1.50 1.70 COLLECTOR COLLECTOR BASE EMITTER COLLECTOR COLLECTOR INCHES MIN MAX 0.059 0.067 0.043 0.051 0.020 0.024 0.007 0.011 0.020 BSC 0.003 0.007 0.004 0.012 0.059 0.067 BC847CDXV6T1, BC847CDXV6T5 BC848CDXV6T1, BC848CDXV6T5 Thermal Clad is a registered trademark of the Bergquist Company. ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. PUBLICATION ORDERING INFORMATION Literature Fulfillment: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: [email protected] JAPAN: ON Semiconductor, Japan Customer Focus Center 2-9-1 Kamimeguro, Meguro-ku, Tokyo, Japan 153-0051 Phone: 81-3-5773-3850 ON Semiconductor Website: http://onsemi.com For additional information, please contact your local Sales Representative. N. American Technical Support: 800-282-9855 Toll Free USA/Canada http://onsemi.com 6 BC847CDXV6T1/D