a 2.5 V to 5.5 V, 500 A, Parallel Interface Quad Voltage-Output 8-/10-/12-Bit DACs AD5334/AD5335/AD5336/AD5344* FEATURES AD5334: Quad 8-Bit DAC in 24-Lead TSSOP AD5335: Quad 10-Bit DAC in 24-Lead TSSOP AD5336: Quad 10-Bit DAC in 28-Lead TSSOP AD5344: Quad 12-Bit DAC in 28-Lead TSSOP Low Power Operation: 500 A @ 3 V, 600 A @ 5 V Power-Down to 80 nA @ 3 V, 200 nA @ 5 V via PD Pin 2.5 V to 5.5 V Power Supply Double-Buffered Input Logic Guaranteed Monotonic by Design Over All Codes Output Range: 0–VREF or 0–2 V REF Power-On Reset to Zero Volts Simultaneous Update of DAC Outputs via LDAC Pin Asynchronous CLR Facility Low Power Parallel Data Interface On-Chip Rail-to-Rail Output Buffer Amplifiers Temperature Range: –40ⴗC to +105ⴗC APPLICATIONS Portable Battery-Powered Instruments Digital Gain and Offset Adjustment Programmable Voltage and Current Sources Programmable Attenuators Industrial Process Control GENERAL DESCRIPTION The AD5334/AD5335/AD5336/AD5344 are quad 8-, 10-, and 12-bit DACs. They operate from a 2.5 V to 5.5 V supply consuming just 500 µA at 3 V, and feature a power-down mode that further reduces the current to 80 nA. These devices incorporate an on-chip output buffer that can drive the output to both supply rails. The AD5334/AD5335/AD5336/AD5344 have a parallel interface. CS selects the device and data is loaded into the input registers on the rising edge of WR. The GAIN pin on the AD5334 and AD5336 allows the output range to be set at 0 V to VREF or 0 V to 2 × VREF. Input data to the DACs is double-buffered, allowing simultaneous update of multiple DACs in a system using the LDAC pin. On the AD5334, AD5335 and AD5336 an asynchronous CLR input is also provided. This resets the contents of the Input Register and the DAC Register to all zeros. These devices also incorporate a power-on-reset circuit that ensures that the DAC output powers on to 0 V and remains there until valid data is written to the device. The AD5334/AD5335/AD5336/AD5344 are available in Thin Shrink Small Outline Packages (TSSOP). AD5334 FUNCTIONAL BLOCK DIAGRAM (Other Diagrams Inside) VREFA/B VDD POWER-ON RESET AD5334 GAIN DB .7 .. INPUT REGISTER DAC REGISTER 8-BIT DAC BUFFER VOUTA INPUT REGISTER DAC REGISTER 8-BIT DAC BUFFER VOUTB INPUT REGISTER DAC REGISTER 8-BIT 8-BIT DAC DAC BUFFER VOUTC INPUT REGISTER DAC REGISTER 8-BIT DAC BUFFER VOUTD DB0 CS WR A0 INTERFACE LOGIC A1 TO ALL DACS AND BUFFERS CLR LDAC *Protected by U.S. Patent Number 5,969,657. POWER-DOWN LOGIC VREFC/D PD GND REV. 0 Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781/329-4700 World Wide Web Site: http://www.analog.com Fax: 781/326-8703 © Analog Devices, Inc., 2000 AD5334/AD5335/AD5336/AD5344–SPECIFICATIONS (V = 2.5 V to 5.5 V, V = 2 V. R = 2 k⍀ to GND; C =200 pF to GND; all specifications T to T unless otherwise noted.) DD REF L L MIN MAX 2 Parameter1 Min B Version Typ Max Unit Conditions/Comments 3, 4 DC PERFORMANCE AD5334 Resolution Relative Accuracy Differential Nonlinearity AD5335/AD5336 Resolution Relative Accuracy Differential Nonlinearity AD5344 Resolution Relative Accuracy Differential Nonlinearity Offset Error Gain Error Lower Deadband5 Upper Deadband Offset Error Drift6 Gain Error Drift6 DC Power Supply Rejection Ratio6 DC Crosstalk6 DAC REFERENCE INPUT6 VREF Input Range VREF Input Impedance Bits LSB LSB Guaranteed Monotonic By Design Over All Codes 10 ± 0.5 ± 0.05 ±4 ± 0.5 Bits LSB LSB Guaranteed Monotonic By Design Over All Codes 0.25 OUTPUT CHARACTERISTICS6 Minimum Output Voltage4, 7 Maximum Output Voltage4, 7 DC Output Impedance Short Circuit Current Power-Up Time LOGIC INPUTS6 Input Current VIL, Input Low Voltage ± 16 ±1 ±3 ±1 60 60 VDD Bits LSB LSB % of FSR % of FSR mV mV ppm of FSR/°C ppm of FSR/°C dB µV 180 90 90 45 –90 –90 V kΩ kΩ kΩ kΩ dB dB 0.001 VDD – 0.001 0.5 50 20 2.5 5 V min V max Ω mA mA µs µs ±1 µA V V V V V V pF 0.8 0.6 0.5 2.4 2.1 2.0 Pin Capacitance POWER REQUIREMENTS VDD IDD (Normal Mode) VDD = 4.5 V to 5.5 V VDD = 2.5 V to 3.6 V IDD (Power-Down Mode) VDD = 4.5 V to 5.5 V VDD = 2.5 V to 3.6 V ±1 ± 0.25 12 ±2 ± 0.2 ± 0.4 ± 0.1 10 10 –12 –5 –60 200 Reference Feedthrough Channel-to-Channel Isolation VIH, Input High Voltage 8 ± 0.15 ± 0.02 3.5 2.5 5.5 V 600 500 900 700 µA µA 0.2 0.08 1 1 µA µA Guaranteed Monotonic By Design Over All Codes Lower Deadband Exists Only if Offset Error Is Negative VDD = 5 V. Upper Deadband Exists Only if VREF = VDD ∆VDD = ± 10% RL = 2 kΩ to GND, 2 kΩ to VDD; CL = 200 pF to GND; Gain = 0 Gain = 1. Input Impedance = RDAC (AD5336/AD5344) Gain = 2. Input Impedance = RDAC (AD5336) Gain = 1. Input Impedance = RDAC (AD5334/AD5335) Gain = 2. Input Impedance = RDAC (AD5334) Frequency = 10 kHz Frequency = 10 kHz Rail-to-Rail Operation VDD = 5 V VDD = 3 V Coming Out of Power-Down Mode. VDD = 5 V Coming Out of Power-Down Mode. VDD = 3 V VDD = 5 V ± 10% VDD = 3 V ± 10% VDD = 2.5 V VDD = 5 V ± 10% VDD = 3 V ± 10% VDD = 2.5 V All DACs active and excluding load currents. VIH = VDD, VIL = GND. IDD increases by 50 µA at VREF > VDD – 100 mV. NOTES 1 See Terminology section. 2 Temperature range: B Version: –40°C to +105°C; typical specifications are at 25°C. 3 Linearity is tested using a reduced code range: AD5334 (Code 8 to 255); AD5335/AD5336 (Code 28 to 1023); AD5344 (Code 115 to 4095). 4 DC specifications tested with outputs unloaded. 5 This corresponds to x codes. x = Deadband voltage/LSB size. 6 Guaranteed by design and characterization, not production tested. 7 In order for the amplifier output to reach its minimum voltage, Offset Error must be negative. In order for the amplifier output to reach its maximum voltage, V REF = VDD and “Offset plus Gain” Error must be positive. Specifications subject to change without notice. –2– REV. 0 AD5334/AD5335/AD5336/AD5344 (VDD = 2.5 V to 5.5 V. RL = 2 k⍀ to GND; CL = 200 pF to GND. All specifications TMIN to TMAX unless other- AC CHARACTERISTICS1 wise noted.) 2 Parameter B Version3 Min Typ Max Unit 6 7 7 8 0.7 8 0.5 3 0.5 3.5 200 –70 µs µs µs µs V/µs nV-s nV-s nV-s nV-s nV-s kHz dB Output Voltage Settling Time AD5334 AD5335 AD5336 AD5344 Slew Rate Major Code Transition Glitch Energy Digital Feedthrough Digital Crosstalk Analog Crosstalk DAC-to-DAC Crosstalk Multiplying Bandwidth Total Harmonic Distortion 8 9 9 10 Conditions/Comments VREF = 2 V. See Figure 20 1/4 Scale to 3/4 Scale Change (40 H to C0 H) 1/4 Scale to 3/4 Scale Change (100 H to 300 H) 1/4 Scale to 3/4 Scale Change (100 H to 300 H) 1/4 Scale to 3/4 Scale Change (400 H to C00 H) 1 LSB Change Around Major Carry VREF = 2 V ± 0.1 V p-p. Unbuffered Mode VREF = 2.5 V ± 0.1 V p-p. Frequency = 10 kHz NOTES 1 Guaranteed by design and characterization, not production tested. 2 See Terminology section. 3 Temperature range: B Version: –40°C to +105°C; typical specifications are at 25°C. Specifications subject to change without notice. TIMING CHARACTERISTICS1, 2, 3 (V DD = 2.5 V to 5.5 V, All specifications TMIN to TMAX unless otherwise noted.) Parameter Limit at TMIN, TMAX Unit Condition/Comments t1 t2 t3 t4 t5 t6 t7 t8 t9 t10 t11 t12 t13 t14 t15 0 0 20 5 4.5 5 5 4.5 5 4.5 20 20 50 20 0 ns min ns min ns min ns min ns min ns min ns min ns min ns min ns min ns min ns min ns min ns min ns min CS to WR Setup Time CS to WR Hold Time WR Pulsewidth Data, GAIN, HBEN Setup Time Data, GAIN, HBEN Hold Time Synchronous Mode. WR Falling to LDAC Falling. Synchronous Mode. LDAC Falling to WR Rising. Synchronous Mode. WR Rising to LDAC Rising. Asynchronous Mode. LDAC Rising to WR Rising. Asynchronous Mode. WR Rising to LDAC Falling. LDAC Pulsewidth CLR Pulsewidth Time Between WR Cycles A0, A1 Setup Time A0, A1 Hold Time NOTES 1 Guaranteed by design and characterization, not production tested. 2 All input signals are specified with tr = tf = 5 ns (10% to 90% of V DD) and timed from a voltage level of (V IL + VIH)/2. 3 See Figure 1. t2 t1 CS t 13 t3 Specifications subject to change without notice. WR t4 DATA, GAIN, HBEN t6 LDAC 1 t7 t5 t8 t9 t 10 t 11 LDAC 2 t 14 CLR t 15 t 12 A0, A1 NOTES: 1 SYNCHRONOUS LDAC UPDATE MODE 2 ASYNCHRONOUS LDAC UPDATE MODE Figure 1. Parallel Interface Timing Diagram REV. 0 –3– AD5334/AD5335/AD5336/AD5344 Reflow Soldering Peak Temperature . . . . . . . . . . . . . . . . . . . . . . 220 +5/–0°C Time at Peak Temperature . . . . . . . . . . . . .10 sec to 40 sec ABSOLUTE MAXIMUM RATINGS* (TA = 25°C unless otherwise noted) VDD to GND . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to +7 V Digital Input Voltage to GND . . . . . . . . –0.3 V to VDD + 0.3 V Digital Output Voltage to GND . . . . . . –0.3 V to VDD + 0.3 V Reference Input Voltage to GND . . . . –0.3 V to VDD + 0.3 V VOUT to GND . . . . . . . . . . . . . . . . . . . –0.3 V to VDD + 0.3 V Operating Temperature Range Industrial (B Version) . . . . . . . . . . . . . . . –40°C to +105°C Storage Temperature Range . . . . . . . . . . . . –65°C to +150°C Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . 150°C TSSOP Package Power Dissipation . . . . . . . . . . . . . . . (TJ max – TA)/θJA mW θJA Thermal Impedance (24-Lead TSSOP) . . . . . 128°C/W θJA Thermal Impedance (28-Lead TSSOP) . . . . . 97.9°C/W θJC Thermal Impedance (24-Lead TSSOP) . . . . . . 42°C/W θJC Thermal Impedance (28-Lead TSSOP) . . . . . . 14°C/W *Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those listed in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ORDERING GUIDE Model Temperature Range Package Description Package Option AD5334BRU AD5335BRU AD5336BRU AD5344BRU –40°C to +105°C –40°C to +105°C –40°C to +105°C –40°C to +105°C TSSOP (Thin Shrink Small Outline Package) TSSOP (Thin Shrink Small Outline Package) TSSOP (Thin Shrink Small Outline Package) TSSOP (Thin Shrink Small Outline Package) RU-24 RU-24 RU-28 RU-28 CAUTION ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the human body and test equipment and can discharge without detection. Although the AD5334/AD5335/AD5336/AD5344 features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high-energy electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degradation or loss of functionality. –4– WARNING! ESD SENSITIVE DEVICE REV. 0 AD5334/AD5335/AD5336/AD5344 AD5334 PIN CONFIGURATION AD5334 FUNCTIONAL BLOCK DIAGRAM VREFA/B VDD POWER-ON RESET AD5334 GAIN INPUT REGISTER DB .. 7 . DB0 A0 8-BIT DAC BUFFER VOUTA 24 CLR VREFA/B 2 23 GAIN VOUTA 3 22 DB7 VOUTB 4 21 DB6 20 DB5 VOUTC 5 8-BIT AD5334 VOUTD 6 TOP VIEW 19 DB4 GND 7 (Not to Scale) 18 DB3 CS WR DAC REGISTER VREFC/D 1 INPUT REGISTER DAC REGISTER 8-BIT DAC BUFFER VOUTB INTERFACE LOGIC A1 INPUT REGISTER DAC REGISTER 8-BIT 8-BIT DAC DAC BUFFER VOUTC INPUT REGISTER DAC REGISTER 8-BIT DAC BUFFER VOUTD CS 8 17 DB2 WR 9 16 DB1 A0 10 15 DB0 A1 11 14 VDD LDAC 12 13 PD TO ALL DACS AND BUFFERS CLR LDAC POWER-DOWN LOGIC VREFC/D PD GND AD5334 PIN FUNCTION DESCRIPTIONS Pin No. Mnemonic Function 1 2 3 4 5 6 7 8 9 10 11 12 VREFC/D VREFA/B VOUTA VOUTB VOUTC VOUTD GND CS WR A0 A1 LDAC 13 14 PD VDD 15–22 23 24 DB0–DB7 GAIN CLR Unbuffered Reference Input for DACs C and D. Unbuffered Reference Input for DACs A and B. Output of DAC A. Buffered Output with Rail-to-Rail Operation. Output of DAC B. Buffered Output with Rail-to-Rail Operation. Output of DAC C. Buffered Output with Rail-to-Rail Operation. Output of DAC D. Buffered Output with Rail-to-Rail Operation. Ground Reference Point for All Circuitry on the Part. Active Low Chip Select Input. This is used in conjunction with WR to write data to the parallel interface. Active Low Write Input. This is used in conjunction with CS to write data to the parallel interface. LSB Address Pin for Selecting which DAC Is to Be Written to. MSB Address Pin for Selecting which DAC Is to Be Written to. Active Low Control Input that Updates the DAC Registers with the Contents of the Input Registers. This allows all DAC outputs to be simultaneously updated. Power-Down Pin. This active low control pin puts all DACs into power-down mode. Power Supply Pin. This part can operate from 2.5 V to 5.5 V and the supply should be decoupled with a 10 µF capacitor in parallel with a 0.1 µF capacitor to GND. Eight Parallel Data Inputs. DB7 is the MSB of these eight bits. Gain Control Pin. This controls whether the output range from the DAC is 0–VREF or 0–2 VREF Asynchronous Active Low Control Input that Clears All Input Registers and DAC Registers to Zeros. REV. 0 –5– AD5334/AD5335/AD5336/AD5344 AD5335 FUNCTIONAL BLOCK DIAGRAM AD5335 PIN CONFIGURATION VREFA/B VDD POWER-ON RESET AD5335 HIGH BYTE REGISTER 24 CLR 23 HBEN VOUTA 3 22 DB7 VOUTB 4 21 DB6 20 DB5 VOUTC 5 DB .. 7 .. . . DB0 LOW BYTE REGISTER CS DAC REGISTER 10-BIT DAC A0 LOW BYTE REGISTER INTERFACE LOGIC 10-BIT AD5335 VOUTD 6 BUFFER VOUTA HIGH BYTE REGISTER WR A1 VREFC/D 1 VREFA/B 2 DAC REGISTER 10-BIT DAC BUFFER VOUTB DAC REGISTER 10-BIT DAC BUFFER VOUTC DAC REGISTER 10-BIT DAC BUFFER VOUTD TOP VIEW 19 DB4 GND 7 (Not to Scale) 18 DB3 CS 8 17 DB2 WR 9 16 DB1 A0 10 15 DB0 A1 11 14 VDD LDAC 12 13 PD HIGH BYTE REGISTER HBEN LOW BYTE REGISTER HIGH BYTE REGISTER LOW BYTE REGISTER TO ALL DACS AND BUFFERS RESET CLR POWER-DOWN LOGIC LDAC VREFC/D PD GND AD5335 PIN FUNCTION DESCRIPTIONS Pin No. Mnemonic Function 1 2 3 4 5 6 7 8 9 10 11 12 VREFC/D VREFA/B VOUTA VOUTB VOUTC VOUTD GND CS WR A0 A1 LDAC 13 14 PD VDD 15–22 23 DB0–DB7 HBEN 24 CLR Unbuffered Reference Input for DACs C and D. Unbuffered Reference Input for DACs A and B. Output of DAC A. Buffered output with rail-to-rail operation. Output of DAC B. Buffered output with rail-to-rail operation. Output of DAC C. Buffered output with rail-to-rail operation. Output of DAC D. Buffered output with rail-to-rail operation. Ground Reference Point for All Circuitry on the Part. Active Low Chip Select Input. This is used in conjunction with WR to write data to the parallel interface. Active Low Write Input. This is used in conjunction with CS to write data to the parallel interface. LSB Address Pin for Selecting which DAC Is to Be Written to. MSB Address Pin for Selecting which DAC Is to Be Written to. Active Low Control Input that Updates the DAC Registers with the Contents of the Input Registers. This allows all DAC outputs to be simultaneously updated. Power-Down Pin. This active low control pin puts all DACs into power-down mode. Power Supply Pin. This part can operate from 2.5 V to 5.5 V and the supply should be decoupled with a 10 µF capacitor in parallel with a 0.1 µF capacitor to GND. Eight Parallel Data Inputs. DB7 is the MSB of these eight bits. This pin is used when writing to the device to determine if data is written to the high byte register or the low byte register. Asynchronous Active Low Control Input that Clears All Input Registers and DAC Registers to Zeros. –6– REV. 0 AD5334/AD5335/AD5336/AD5344 AD5336 PIN CONFIGURATION AD5336 FUNCTIONAL BLOCK DIAGRAM VREFA VREFB VDD POWER-ON RESET AD5336 GAIN INPUT REGISTER DB .. 9 . DB0 A0 10-BIT DAC BUFFER VOUTA 28 CLR 27 GAIN VREFB 3 26 DB9 VREFA 4 25 DB8 VOUTA 5 24 DB7 23 DB6 VOUTB 6 CS WR DAC REGISTER VREFD 1 VREFC 2 INPUT REGISTER DAC REGISTER 10-BIT DAC BUFFER VOUTB INTERFACE LOGIC INPUT REGISTER A1 INPUT REGISTER DAC REGISTER DAC REGISTER 10-BIT DAC 10-BIT DAC BUFFER VOUTC BUFFER 10-BIT AD5336 VOUTC 7 22 GND 9 20 DB3 CS 10 19 DB2 WR 11 18 DB1 A0 12 17 DB0 A1 13 16 VDD LDAC 14 15 PD DB5 TOP VIEW VOUTD 8 (Not to Scale) 21 DB4 VOUTD TO ALL DACS AND BUFFERS CLR RESET LDAC POWER-DOWN LOGIC VREFD PD VREFC GND AD5336 PIN FUNCTION DESCRIPTIONS Pin No. Mnemonic Function 1 2 3 4 5 6 7 8 9 10 11 12 13 14 VREFD VREFC VREFB VREFA VOUTA VOUTB VOUTC VOUTD GND CS WR A0 A1 LDAC 15 16 PD VDD 17–26 27 28 DB0–DB9 GAIN CLR Unbuffered Reference Input for DAC D. Unbuffered Reference Input for DAC C. Unbuffered Reference Input for DAC B. Unbuffered Reference Input for DAC A. Output of DAC A. Buffered output with rail-to-rail operation. Output of DAC B. Buffered output with rail-to-rail operation. Output of DAC C. Buffered output with rail-to-rail operation. Output of DAC D. Buffered output with rail-to-rail operation. Ground Reference Point for All Circuitry on the Part. Active Low Chip Select Input. This is used in conjunction with WR to write data to the parallel interface. Active Low Write Input. This is used in conjunction with CS to write data to the parallel interface. LSB Address Pin for Selecting which DAC Is to Be Written to. MSB Address Pin for Selecting which DAC is to Be Written to. Active Low Control Input that Updates the DAC Registers with the Contents of the Input Registers. This allows all DAC outputs to be simultaneously updated. Power-Down Pin. This active low control pin puts all DACs into power-down mode. Power Supply Pin. This part can operate from 2.5 V to 5.5 V and the supply should be decoupled with a 10 µF capacitor in parallel with a 0.1 µF capacitor to GND. 10 Parallel Data Inputs. DB9 is the MSB of these 10 bits. Gain Control Pin. This controls whether the output range from the DAC is 0–VREF or 0–2 VREF. Asynchronous Active Low Control Input that Clears All Input Registers and DAC Registers to Zeros. REV. 0 –7– AD5334/AD5335/AD5336/AD5344 AD5344 PIN CONFIGURATION AD5344 FUNCTIONAL BLOCK DIAGRAM VREFA VDD VREFB POWER-ON RESET DB. 11 . ... . DB0 INPUT REGISTER CS WR A0 INPUT REGISTER AD5344 DAC REGISTER DAC REGISTER 12-BIT DAC 12-BIT DAC BUFFER VOUTA INPUT REGISTER INPUT REGISTER DAC REGISTER DAC REGISTER 12-BIT DAC 12-BIT DAC 28 DB11 27 DB10 VREFB 3 26 DB9 VREFA 4 25 DB8 VOUTA 5 24 DB7 23 DB6 VOUTB 6 12-BIT AD5344 VOUTC 7 22 GND 9 20 DB3 CS 10 19 DB2 WR 11 18 DB1 A0 12 17 DB0 A1 13 16 VDD LDAC 14 15 PD DB5 TOP VIEW VOUTD 8 (Not to Scale) 21 DB4 BUFFER VOUTB INTERFACE LOGIC A1 VREFD 1 VREFC 2 BUFFER VOUTC BUFFER VOUTD TO ALL DACS AND BUFFERS LDAC POWER-DOWN LOGIC VREFD PD VREFC GND AD5344 PIN FUNCTION DESCRIPTIONS Pin No. Mnemonic Function 1 2 3 4 5 6 7 8 9 10 11 12 13 14 VREFD VREFC VREFB VREFA VOUTA VOUTB VOUTC VOUTD GND CS WR A0 A1 LDAC 15 16 PD VDD 17–28 DB0–DB11 Unbuffered Reference Input for DAC D. Unbuffered Reference Input for DAC C. Unbuffered Reference Input for DAC B. Unbuffered Reference Input for DAC A. Output of DAC A. Buffered output with rail-to-rail operation. Output of DAC B. Buffered output with rail-to-rail operation. Output of DAC C. Buffered output with rail-to-rail operation. Output of DAC D. Buffered output with rail-to-rail operation. Ground Reference Point for All Circuitry on the Part. Active Low Chip Select Input. This is used in conjunction with WR to write data to the parallel interface. Active Low Write Input. This is used in conjunction with CS to write data to the parallel interface. LSB Address Pin for Selecting which DAC Is to Be Written to. MSB Address Pin for Selecting which DAC Is to Be Written to. Active Low Control Input that Updates the DAC Registers with the Contents of the Input Registers. This allows all DAC outputs to be simultaneously updated. Power-Down Pin. This active low control pin puts all DACs into power-down mode. Power Supply Pin. This part can operate from 2.5 V to 5.5 V and the supply should be decoupled with a 10 µF capacitor in parallel with a 0.1 µF capacitor to GND. 12 Parallel Data Inputs. DB11 is the MSB of these 12 bits. –8– REV. 0 AD5334/AD5335/AD5336/AD5344 TERMINOLOGY RELATIVE ACCURACY GAIN ERROR AND OFFSET ERROR For the DAC, Relative Accuracy or Integral Nonlinearity (INL) is a measure of the maximum deviation, in LSBs, from a straight line passing through the actual endpoints of the DAC transfer function. Typical INL versus Code plot can be seen in Figures 5, 6, and 7. ACTUAL OUTPUT VOLTAGE DIFFERENTIAL NONLINEARITY Differential Nonlinearity (DNL) is the difference between the measured change and the ideal 1 LSB change between any two adjacent codes. A specified differential nonlinearity of ± 1 LSB maximum ensures monotonicity. This DAC is guaranteed monotonic by design. Typical DNL versus Code plot can be seen in Figures 8, 9, and 10. IDEAL POSITIVE OFFSET OFFSET ERROR DAC CODE This is a measure of the offset error of the DAC and the output amplifier. It is expressed as a percentage of the full-scale range. Figure 3. Positive Offset Error and Gain Error If the offset voltage is positive, the output voltage will still be positive at zero input code. This is shown in Figure 3. Because the DACs operate from a single supply, a negative offset cannot appear at the output of the buffer amplifier. Instead, there will be a code close to zero at which the amplifier output saturates (amplifier footroom). Below this code there will be a deadband over which the output voltage will not change. This is illustrated in Figure 4. GAIN ERROR AND OFFSET ERROR IDEAL OUTPUT VOLTAGE GAIN ERROR This is a measure of the span error of the DAC (including any error in the gain of the buffer amplifier). It is the deviation in slope of the actual DAC transfer characteristic from the ideal expressed as a percentage of the full-scale range. This is illustrated in Figure 2. ACTUAL NEGATIVE OFFSET DAC CODE POSITIVE GAIN ERROR ACTUAL NEGATIVE GAIN ERROR DEADBAND CODES AMPLIFIER FOOTROOM (~1mV) OUTPUT VOLTAGE IDEAL NEGATIVE OFFSET DAC CODE Figure 4. Negative Offset Error and Gain Error Figure 2. Gain Error REV. 0 –9– AD5334/AD5335/AD5336/AD5344 OFFSET ERROR DRIFT DIGITAL FEEDTHROUGH This is a measure of the change in Offset Error with changes in temperature. It is expressed in (ppm of full-scale range)/°C. This is a measure of the change in Gain Error with changes in temperature. It is expressed in (ppm of full-scale range)/°C. Digital Feedthrough is a measure of the impulse injected into the analog output of the DAC from the digital input pins of the device but is measured when the DAC is not being written to (CS held high). It is specified in nV-secs and is measured with a full-scale change on the digital input pins, i.e. from all 0s to all 1s and vice versa. DC POWER-SUPPLY REJECTION RATIO (PSRR) DIGITAL CROSSTALK This indicates how the output of the DAC is affected by changes in the supply voltage. PSRR is the ratio of the change in VOUT to a change in VDD for full-scale output of the DAC. It is measured in dBs. VREF is held at 2 V and VDD is varied ± 10%. This is the glitch impulse transferred to the output of one DAC at midscale in response to a full-scale code change (all 0s to all 1s and vice versa) in the input register of another DAC. It is expressed in nV secs. DC CROSSTALK ANALOG CROSSTALK This is the dc change in the output level of one DAC at midscale in response to a full-scale code change (all 0s to all 1s and vice versa) and output change of another DAC. It is expressed in µV. This is the glitch impulse transferred to the output of one DAC due to a change in the output of another DAC. It is measured by loading one of the input registers with a full-scale code change (all 0s to all 1s and vice versa) while keeping LDAC high. Then pulse LDAC low and monitor the output of the DAC whose digital code was not changed. The area of the glitch is expressed in nV secs. GAIN ERROR DRIFT REFERENCE FEEDTHROUGH This is the ratio of the amplitude of the signal at the DAC output to the reference input when the DAC output is not being updated (i.e., LDAC is high). It is expressed in dBs. DAC-TO-DAC CROSSTALK This is a ratio of the amplitude of the signal at the output of one DAC to a sine wave on the reference inputs of the other DACs. It is measured by grounding one VREF pin and applying a 10 kHz, 4 V peak-to-peak sine wave to the other VREF pins. It is expressed in dBs. This is the glitch impulse transferred to the output of one DAC due to a digital code change and subsequent output change of another DAC. This includes both digital and analog crosstalk. It is measured by loading one of the DACs with a full-scale code change (all 0s to all 1s and vice versa) with the LDAC pin set low and monitoring the output of another DAC. The energy of the glitch is expressed in nV secs. MAJOR-CODE TRANSITION GLITCH ENERGY MULTIPLYING BANDWIDTH Major-Code Transition Glitch Energy is the energy of the impulse injected into the analog output when the DAC changes state. It is normally specified as the area of the glitch in nV secs and is measured when the digital code is changed by 1 LSB at the major carry transition (011 . . . 11 to 100 . . . 00 or 100 . . . 00 to 011 . . . 11). The amplifiers within the DAC have a finite bandwidth. The Multiplying Bandwidth is a measure of this. A sine wave on the reference (with full-scale code loaded to the DAC) appears on the output. The Multiplying Bandwidth is the frequency at which the output amplitude falls to 3 dB below the input. CHANNEL-TO-CHANNEL ISOLATION TOTAL HARMONIC DISTORTION This is the difference between an ideal sine wave and its attenuated version using the DAC. The sine wave is used as the reference for the DAC and the THD is a measure of the harmonics present on the DAC output. It is measured in dBs. –10– REV. 0 Typical Performance Characteristics– AD5334/AD5335/AD5336/AD5344 1.0 12 3 TA = 25ⴗC VDD = 5V TA = 25ⴗC VDD = 5V 2 TA = 25ⴗC VDD = 5V 8 0 INL ERROR – LSBs INL ERROR – LSBs INL ERROR – LSBs 0.5 1 0 –1 4 0 –4 –0.5 –8 –2 0 50 100 150 CODE 200 Figure 5. AD5334 Typical INL Plot 0.3 200 400 600 CODE 800 1000 1000 2000 CODE 3000 4000 Figure 7. AD5336 Typical INL Plot TA = 25ⴗC VDD = 5V TA = 25ⴗC VDD = 5V DNL ERROR – LSBs 0.4 0 –0.1 –0.2 0.2 0 –0.2 0.5 0 –0.5 –0.4 0 50 100 150 CODE 200 –1 –0.6 250 Figure 8. AD5334 Typical DNL Plot 0 200 800 400 600 CODE 0 1000 Figure 9. AD5335 Typical DNL Plot 0.5 TA = 25ⴗC 0.4 MAX INL 0.3 MIN DNL 4000 0.5 0.2 MAX DNL 0.1 0 –0.1 GAIN ERROR 0 OFFSET ERROR MIN DNL –0.2 –0.25 3000 VDD = 5V VREF = 2V MAX INL ERROR – % ERROR – LSBs 0 2000 CODE 1 VDD = 5V VREF = 2V 0.25 MAX DNL 1000 Figure 10. AD5336 Typical DNL Plot 0.5 VDD = 5V ERROR – LSBs 0 1 0.6 0.1 –0.3 –12 0 Figure 6. AD5335 Typical INL Plot TA = 25ⴗC VDD = 5V 0.2 DNL ERROR – LSBs –3 250 DNL ERROR – LSBs –1.0 –0.5 –0.3 MIN INL MIN INL –0.4 –0.5 0 1 2 3 VREF – V 4 Figure 11. AD5334 INL and DNL Error vs. VREF REV. 0 5 –0.5 ⴚ40 0 40 80 120 TEMPERATURE – ⴗC Figure 12. AD5334 INL Error and DNL Error vs. Temperature –11– –1 ⴚ40 0 40 80 120 TEMPERATURE – ⴗC Figure 13. AD5334 Offset Error and Gain Error vs. Temperature AD5334/AD5335/AD5336/AD5344 TA = 25ⴗC VREF = 2V 0.1 3V SOURCE 400 –0.3 –0.4 IDD – A VOUT – Volts –0.2 3 2 OFFSET ERROR 1 VDD = 3.6V 300 TA = 25ⴗC VREF = 2V 100 3V SINK 5V SINK 0 0 1 2 4 3 VDD – Volts 5 6 Figure 14. Offset Error and Gain Error vs. VDD 0 1 3 4 2 5 SINK/SOURCE CURRENT – mA 0 ZERO-SCALE 6 FULL SCALE 1800 0.5 TA = 25ⴗC DAC CODE Figure 16. Supply Current vs. DAC Code Figure 15. VOUT Source and Sink Current Capability TA = 25ⴗC 500 1600 0.4 1400 1200 300 0.3 IDD – A IDD – A 400 IDD – A VDD = 5.5V 200 –0.5 600 500 GAIN ERROR –0.1 –0.6 5V SOURCE 4 0 ERROR – % 600 5 0.2 0.2 1000 800 600 200 0.1 100 VDD = 5V 400 VDD = 3V 200 0 2.5 3.0 3.5 4.0 VDD – V 4.5 5.0 Figure 17. Supply Current vs. Supply Voltage CH1 0 2.5 5.5 TA = 25 ⴗC 5µs VDD = 5V VREF = 5V 0 3.0 3.5 4.0 4.5 VDD – V 5.0 5.5 CH1 1 2 3 VLOGIC – V 4 5 Figure 19. Supply Current vs. Logic Input Voltage Figure 18. Power-Down Current vs. Supply Voltage VOUTA 0 TA = 25ⴗC VDD = 5V VREF = 2V TA = 25ⴗC VDD = 5V VREF = 2V VDD CH1 VOUTA LDAC VOUTA CH2 CH2 CH1 1V, CH2 5V, TIME BASE= 1s/DIV Figure 20. Half-Scale Settling (1/4 to 3/4 Scale Code Change) PD CH2 CH1 2V, CH2 200mV, TIME BASE = 200s/DIV Figure 21. Power-On Reset to 0 V –12– CH1 500mV, CH2 5V, TIME BASE = 1s/DIV Figure 22. Exiting Power-Down to Midscale REV. 0 AD5334/AD5335/AD5336/AD5344 0.929 10 0.928 0 0.927 –10 0.926 0.925 –20 dB VDD = 5V VOUT – Volts FREQUENCY VDD = 3V 0.924 –30 0.923 0.922 –40 0.921 –50 0.920 0.919 300 350 400 450 500 IDD – A 550 –60 0.01 500ns/DIV 600 Figure 23. IDD Histogram with VDD = 3 V and VDD = 5 V Figure 24. AD5344 Major-Code Transition Glitch Energy 0.1 1 10 100 FREQUENCY – kHz 1k 10k Figure 25. Multiplying Bandwidth (Small-Signal Frequency Response) VDD = 5V TA = 25ⴗC 0.3 0.2 1mV/DIV FULL-SCALE ERROR – %FSR 0.4 0.1 0 –0.1 –0.2 0 1 2 3 VREF – V 4 5 6 Figure 26. Full-Scale Error vs. VREF 750ns/DIV Figure 27. DAC-DAC Crosstalk FUNCTIONAL DESCRIPTION The AD5334/AD5335/AD5336/AD5344 are quad resistorstring DACs fabricated on a CMOS process with resolutions of 8, 10, 10, and 12 bits, respectively. They are written to using a parallel interface. They operate from single supplies of 2.5 V to 5.5 V and the output buffer amplifiers offer rail-to-rail output swing. The gain of the buffer amplifiers in the AD5334 and AD5336 can be set to 1 or 2 to give an output voltage range of 0 to VREF or 0 to 2 VREF. The AD5335 and AD5344 have output buffers with unity gain. where: D = decimal equivalent of the binary code which is loaded to the DAC register: 0–255 for AD5334 (8 Bits) 0–1023 for AD5335/AD5336 (10 Bits) 0–4095 for AD5344 (12 Bits) N = DAC resolution Gain = Output Amplifier Gain (1 or 2) The devices have a power-down feature that reduces current consumption to only 80 nA @ 3 V. VREF GAIN Digital-to-Analog Section The architecture of one DAC channel consists of a reference buffer and a resistor-string DAC followed by an output buffer amplifier. The voltage at the VREF pin provides the reference voltage for the DAC. Figure 28 shows a block diagram of the DAC architecture. Since the input coding to the DAC is straight binary, the ideal output voltage is given by: VOUT = VREF × REV. 0 INPUT REGISTER DAC REGISTER RESISTOR STRING VOUT OUTPUT BUFFER AMPLIFIER Figure 28. Single DAC Channel Architecture D × Gain 2N –13– AD5334/AD5335/AD5336/AD5344 Access to the DAC register is controlled by the LDAC function. When LDAC is high, the DAC register is latched and the input register may change state without affecting the contents of the DAC register. However, when LDAC is brought low, the DAC register becomes transparent and the contents of the input register are transferred to it. The gain control signal is also double-buffered and is only updated when LDAC is taken low. Resistor String The resistor string section is shown in Figure 29. It is simply a string of resistors, each of value R. The digital code loaded to the DAC register determines at what node on the string the voltage is tapped off to be fed into the output amplifier. The voltage is tapped off by closing one of the switches connecting the string to the amplifier. Because it is a string of resistors, it is guaranteed monotonic. This is useful if the user requires simultaneous updating of all DACs and peripherals. The user may write to all input registers individually and then, by pulsing the LDAC input low, all outputs will update simultaneously. VREF R Double-buffering is also useful where the DAC data is loaded in two bytes, as in the AD5335, because it allows the whole data word to be assembled in parallel before updating the DAC register. This prevents spurious outputs that could occur if the DAC register were updated with only the high byte or the low byte. R R TO OUTPUT AMPLIFIER These parts contain an extra feature whereby the DAC register is not updated unless its input register has been updated since the last time that LDAC was brought low. Normally, when LDAC is brought low, the DAC registers are filled with the contents of the input registers. In the case of the AD5334/ AD5335/AD5336/AD5344, the part will only update the DAC register if the input register has been changed since the last time the DAC register was updated. This removes unnecessary crosstalk. R R Figure 29. Resistor String DAC Reference Input The DACs operate with an external reference. The reference inputs are unbuffered and have an input range of 0.25 V to VDD. The impedance per DAC is typically 180 kΩ for 0–VREF mode and 90 kΩ for 0–2 VREF mode. The AD5336 and AD5344 have separate reference inputs for each DAC, while the AD5334 and AD5335 have a reference inputs for each pair of DACS (A/B and C/D). Clear Input (CLR) CLR is an active low, asynchronous clear that resets the input and DAC registers. Note that the AD5344 has no CLR function. Chip Select Input (CS) CS is an active low input that selects the device. Write Input (WR) WR is an active low input that controls writing of data to the device. Data is latched into the input register on the rising edge of WR. Output Amplifier The output buffer amplifier is capable of generating output voltages to within 1 mV of either rail. Its actual range depends on VREF, GAIN, the load on VOUT, and offset error. Load DAC Input (LDAC) LDAC transfers data from the input register to the DAC register (and hence updates the outputs). Use of the LDAC function enables double buffering of the DAC and GAIN data. There are two LDAC modes: If a gain of 1 is selected (GAIN = 0), the output range is 0.001 V to VREF. If a gain of 2 is selected (GAIN = 1), the output range is 0.001 V to 2 VREF. However because of clamping the maximum output is limited to VDD – 0.001 V. Synchronous Mode: In this mode the DAC register is updated after new data is read in on the rising edge of the WR input. LDAC can be tied permanently low or pulsed as in Figure 1. The output amplifier is capable of driving a load of 2 kΩ to GND or VDD, in parallel with 500 pF to GND or VDD. The source and sink capabilities of the output amplifier can be seen in Figure 15. The slew rate is 0.7 V/µs with a half-scale settling time to ±0.5 LSB (at 8 bits) of 6 µs with the output unloaded. See Figure 20. Asynchronous Mode: In this mode the outputs are not updated at the same time that the input register is written to. When LDAC goes low the DAC register is updated with the contents of the input register. High-Byte Enable Input (HBEN) PARALLEL INTERFACE The AD5334, AD5336, and AD5344 load their data as a single 8-, 10-, or 12-bit word, while the AD5335 loads data as a low byte of 8 bits and a high byte containing 2 bits. Double-Buffered Interface The AD5334/AD5335/AD5336/AD5344 DACs all have doublebuffered interfaces consisting of an input register and a DAC register. DAC data and GAIN inputs (when available) are written to the input register under control of the Chip Select (CS) and Write (WR). High-Byte Enable is a control input on the AD5335 only that determines if data is written to the high-byte input register or the low-byte input register. The low data byte of the AD5335 consists of data bits 0 to 7 at data inputs DB0 to DB7, while the high byte consists of Data Bits 8 and 9 at data inputs DB0 and DB1. DB2 to DB7 are ignored during a high byte write. See Figure 30. –14– REV. 0 AD5334/AD5335/AD5336/AD5344 When the PD pin is high, the DACs work normally with a typical power consumption of 600 µA at 5 V (500 µA at 3 V). In powerdown mode, however, the supply current falls to 200 nA at 5 V (80 nA at 3 V) when the DACs are powered down. Not only does the supply current drop, but the output stage is also internally switched from the output of the amplifier, making it open-circuit. This has the advantage that the outputs are three-state while the part is in power-down mode, and provides a defined input condition for whatever is connected to the outputs of the DAC amplifiers. The output stage is illustrated in Figure 31. HIGH BYTE X X X X X X DB9 DB8 LOW BYTE DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 X = UNUSED BIT Figure 30. Data Format For AD5335 POWER-ON RESET The AD5334/AD5335/AD5336/AD5344 are provided with a power-on reset function, so that they power up in a defined state. The power-on state is: • Normal operation • 0 – VREF output range • Output voltage set to 0 V RESISTOR STRING DAC AMPLIFIER VOUT POWER-DOWN CIRCUITRY Both input and DAC registers are filled with zeros and remain so until a valid write sequence is made to the device. This is particularly useful in applications where it is important to know the state of the DAC outputs while the device is powering up. Figure 31. Output Stage During Power-Down The bias generator, the output amplifier, the resistor string, and all other associated linear circuitry are all shut down when the power-down mode is activated. However, the contents of the registers are unaffected when in power-down. The time to exit power-down is typically 2.5 µs for VDD = 5 V and 5 µs when VDD = 3 V. This is the time from a rising edge on the PD pin to when the output voltage deviates from its power-down voltage. See Figure 22. POWER-DOWN MODE The AD5334/AD5335/AD5336/AD5344 have low power consumption, dissipating typically 1.5 mW with a 3 V supply and 3 mW with a 5 V supply. Power consumption can be further reduced when the DACs are not in use by putting them into power-down mode, which is selected by taking pin PD low. Table I. AD5334/AD5336/AD5344 Truth Table CLR LDAC CS WR A1 A0 Function 1 1 0 1 1 1 1 1 1 1 X 1 1 1 1 0 1 X X 0 0 0 0 X X 1 X 0➝1 0➝1 0➝1 0➝1 X X X X 0 0 1 1 X X X X 0 1 0 1 X No Data Transfer No Data Transfer Clear All Registers Load DAC A Input Register, GAIN A (AD5334/AD5336) Load DAC B Input Register, GAIN B (AD5334/AD5336) Load DAC C Input Register, GAIN C (AD5334/AD5336) Load DAC D Input Register, GAIN D (AD5334/AD5336) Update DAC Registers X = don’t care. Table II. AD5335 Truth Table CLR LDAC CS WR A1 A0 HBEN Function 1 1 0 1 1 1 1 1 1 1 1 1 1 1 X 1 1 1 1 1 1 1 1 0 1 X X 0 0 0 0 0 0 0 0 X X 1 X 0➝1 0➝1 0➝1 0➝1 0➝1 0➝1 0➝1 0➝1 X X X X 0 0 0 0 1 1 1 1 X X X X 0 0 1 1 0 0 1 1 X X X X 0 1 0 1 0 1 0 1 X No Data Transfer No Data Transfer Clear All Registers Load DAC A Low Byte Input Register Load DAC A High Byte Input Register Load DAC B Low Byte Input Register Load DAC B High Byte Input Register Load DAC C Low Byte Input Register Load DAC C High Byte Input Register Load DAC D Low Byte Input Register Load DAC D High Byte Input Register Update DAC Registers X = don’t care. REV. 0 –15– AD5334/AD5335/AD5336/AD5344 SUGGESTED DATABUS FORMATS 6V TO 16V In many applications the GAIN input of the AD5334 and AD5336 may be hard-wired. However, if more flexibility is required, it can be included in a data bus. This enables the user to software program GAIN, giving the option of doubling the resolution in the lower half of the DAC range. In a bused system GAIN may be treated as a data input since it is written to the device during a write operation and takes effect when LDAC is taken low. This means that the output amplifier gain of multiple DAC devices can be controlled using a common GAIN line. 0.1F VIN ADM663/ADM666 VOUT(2) VSET GND SHDN X X Figure 34. Using an ADM663/ADM666 as Power and Reference to AD5334/AD5335/AD5336/AD5344 GAIN DB9 DB8 DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 Bipolar Operation Using the AD5334/AD5335/AD5336/AD5344 X = UNUSED BIT The AD5334/AD5335/AD5336/AD5344 have been designed for single supply operation, but bipolar operation is achievable using the circuit shown in Figure 35. The circuit shown has been configured to achieve an output voltage range of –5 V < VO < +5 V. Rail-to-rail operation at the amplifier output is achievable using an AD820 or OP295 as the output amplifier. Figure 32. AD5336 Data Format for Byte Load with GAIN Data on 8-Bit Bus APPLICATIONS INFORMATION Typical Application Circuits The AD5334/AD5335/AD5336/AD5344 can be used with a wide range of reference voltages and offer full, one-quadrant multiplying capability over a reference range of 0.25 V to VDD. More typically, these devices may be used with a fixed, precision reference voltage. Figure 33 shows a typical setup for the devices when using an external reference connected to the reference inputs. Suitable references for 5 V operation are the AD780 and REF192. For 2.5 V operation, a suitable external reference would be the AD589, a 1.23 V bandgap reference. The output voltage for any input code can be calculated as follows: VO = [(1 + R4/R3) × (R2/(R1 + R2) × (2 × VREF × D/2N)] – R4 × VREF/R3 where: D is the decimal equivalent of the code loaded to the DAC, N is DAC resolution and VREF is the reference voltage input. With: VREF = 2.5 V R1 = R3 = 10 kΩ R2 = R4 = 20 kΩ and VDD = 5 V. VOUT = (10 × D/2N) – 5 VDD = 2.5V TO 5.5V 0.1F 10F VIN EXT REF VOUT* AD5334/AD5335/ AD5336/AD5344 *ONLY ONE CHANNEL OF VREF AND VOUT SHOWN AD5336 X VREF* 0.1F GND Examples of data formats for putting GAIN on a 16-bit databus are shown in Figure 32. Note that any unused bits above the actual DAC data may be used for GAIN. X VDD SENSE The AD5336 databus must be at least 10 bits wide and is best suited to a 16-bit databus system. X 10F VDD = 5V VDD VOUT GND VREF* R4 20k⍀ VOUT* AD5334/AD5335/ AD5336/AD5344 AD780/REF192 WITH VDD = 5V OR AD589 WITH VDD = 2.5V 0.1F 10F +5V R3 10k⍀ ⴞ5V VIN GND VDD EXT REF *ONLY ONE CHANNEL OF VREF AND VOUT SHOWN GND Figure 33. AD5334/AD5335/AD5336/AD5344 Using External Reference VREF* VOUT 0.1F AD5334/AD5335/ AD5336/AD5344 VOUT* AD780/REF192 WITH VDD = 5V OR AD589 WITH VDD = 2.5V Driving VDD from the Reference Voltage If an output range of zero to V DD is required, the simplest solution is to connect the reference inputs to VDD. As this supply may not be very accurate, and may be noisy, the devices may be powered from the reference voltage, for example using a 5 V reference such as the ADM663 or ADM666, as shown in Figure 34. –5V R1 10k⍀ R2 20k⍀ GND *ONLY ONE CHANNEL OF VREF AND VOUT SHOWN Figure 35. Bipolar Operation using the AD5334/AD5335/ AD5336/AD5344 –16– REV. 0 AD5334/AD5335/AD5336/AD5344 Decoding Multiple AD5334/AD5335/AD5336/AD5344 The CS pin on these devices can be used in applications to decode a number of DACs. In this application, all DACs in the system receive the same data and WR pulses, but only the CS to one of the DACs will be active at any one time, so data will only be written to the DAC whose CS is low. If multiple AD5343s are being used, a common HBEN line will also be required to determine if the data is written to the high-byte or low-byte register of the selected DAC. used for some other purpose. The AD5336 and AD5344 have separate reference inputs for each DAC. The upper and lower limits for the test are loaded to DACs A and B which, in turn, set the limits on the CMP04. If a signal at the VIN input is not within the programmed window, an LED will indicate the fail condition. 5V 0.1F VDD 1G ENABLE CODED ADDRESS VCC 1Y0 1A 1Y1 74HC139 1B 1Y2 1Y3 DGND AD5334/AD5335/ AD5336/AD5344 A1 A0 HBEN* WR DATA INPUTS LDAC CLR CS AD5334/AD5335/ AD5336/AD5344 A1 A0 HBEN* WR LDAC CLR CS 1k⍀ PASS VDD VREFA VOUTA VREFB PASS/ FAIL 1/2 CMP04 AD5336/AD5344 VOUTB 1/6 74HC05 GND Programmable Current Source DATA BUS AD5334/AD5335/ AD5336/AD5344 A1 A0 HBEN* WR DATA INPUTS LDAC CLR CS VREF 1k⍀ FAIL Figure 37. Programmable Window Detector AD5334/AD5335/ AD5336/AD5344 A1 A0 HBEN* WR DATA LDAC INPUTS CLR CS A0 A1 HBEN WR LDAC CLR 10F VIN The 74HC139 is used as a 2- to 4-line decoder to address any of the DACs in the system. To prevent timing errors from occurring, the enable input should be brought to its inactive state while the coded address inputs are changing state. Figure 36 shows a diagram of a typical setup for decoding multiple devices in a system. Once data has been written sequentially to all DACs in a system, all the DACs can be updated simultaneously using a common LDAC line. A common CLR line can also be used to reset all DAC outputs to zero (except on the AD5344). Figure 38 shows the AD5334/AD5335/AD5336/AD5344 used as the control element of a programmable current source. In this example, the full-scale current is set to 1 mA. The output voltage from the DAC is applied across the current setting resistor of 4.7 kΩ in series with the 470 Ω adjustment potentiometer, which gives an adjustment of about ± 5%. Suitable transistors to place in the feedback loop of the amplifier include the BC107 and the 2N3904, which enable the current source to operate from a minimum VSOURCE of 6 V. The operating range is determined by the operating characteristics of the transistor. Suitable amplifiers include the AD820 and the OP295, both having railto-rail operation on their outputs. The current for any digital input code and resistor value can be calculated as follows: D I = G × VREF × N mA (2 × R) Where: G is the gain of the buffer amplifier (1 or 2) D is the digital input code N is the DAC resolution (8, 10, or 12 bits) R is the sum of the resistor plus adjustment potentiometer in kΩ DATA INPUTS VDD = 5V *AD5335 ONLY 0.1F 10F VSOURCE Figure 36. Decoding Multiple DAC Devices VIN AD5334/AD5335/AD5336/AD5344 as a Digitally Programmable Window Detector A digitally programmable upper/lower limit detector using two of the DACs in the AD5334/AD5335/AD5336/AD5344 is shown in Figure 37. VREF* VOUT GND 0.1F LOAD VOUT* AD5334/AD5335/ AD5336/AD5344 AD820/ OP295 AD780/REF192 WITH VDD = 5V Any pair of DACs in the device may be used, but for simplicity the description will refer to DACs A and B. 4.7k⍀ GND 470⍀ Care must be taken to connect the correct reference inputs to the reference source. The AD5334 and AD5335 have only two reference inputs, VREFA/B for DACs A and B and VREFC/D for DACs C and D. If DACs A and B are used (for example) then only VREFA/B is needed. DACs C and D and VREFC/D may be REV. 0 5V VDD EXT REF *ONLY ONE CHANNEL OF VREF AND VOUT SHOWN Figure 38. Programmable Current Source –17– AD5334/AD5335/AD5336/AD5344 Coarse and Fine Adjustment Using the AD5334/AD5335/ AD5336/AD5344 Power Supply Bypassing and Grounding Two of the DACs in the AD5334/AD5335/AD5336/AD5344 can be paired together to form a coarse and fine adjustment function, as shown in Figure 39. As with the window comparator previously described, the description will refer to DACs A, and B and the reference connections will depend on the actual device used. DAC A is used to provide the coarse adjustment while DAC B provides the fine adjustment. Varying the ratio of R1 and R2 will change the relative effect of the coarse and fine adjustments. With the resistor values shown the output amplifier has unity gain for the DAC A output, so the output range is zero to (VREF – 1 LSB). For DAC B the amplifier has a gain of 7.6 × 10–3, giving DAC B a range equal to 2 LSBs of DAC A. The circuit is shown with a 2.5 V reference, but reference voltages up to VDD may be used. The op amps indicated will allow a rail-to-rail output swing. VDD = 5V 0.1F 10F R4 390⍀ 5V VDD VIN EXT REF R3 51.2k⍀ VOUT VOUTA VOUT VREFA R1 390⍀ 0.1F GND AD5336/AD5344 VOUTB AD780/REF192 WITH VDD = 5V R2 51.2k⍀ VREFB GND In any circuit where accuracy is important, careful consideration of the power supply and ground return layout helps to ensure the rated performance. The printed circuit board on which the AD5334/AD5335/AD5336/AD5344 is mounted should be designed so that the analog and digital sections are separated, and confined to certain areas of the board. If the device is in a system where multiple devices require an AGND-to-DGND connection, the connection should be made at one point only. The star ground point should be established as closely as possible to the device. The AD5334/AD5335/AD5336/AD5344 should have ample supply bypassing of 10 µF in parallel with 0.1 µF on the supply located as close to the package as possible, ideally right up against the device. The 10 µF capacitors are the tantalum bead type. The 0.1 µF capacitor should have low Effective Series Resistance (ESR) and Effective Series Inductance (ESI), like the common ceramic types that provide a low impedance path to ground at high frequencies to handle transient currents due to internal logic switching. The power supply lines of the device should use as large a trace as possible to provide low impedance paths and reduce the effects of glitches on the power supply line. Fast switching signals such as clocks should be shielded with digital ground to avoid radiating noise to other parts of the board, and should never be run near the reference inputs. Avoid crossover of digital and analog signals. Traces on opposite sides of the board should run at right angles to each other. This reduces the effects of feedthrough through the board. A microstrip technique is by far the best, but not always possible with a double-sided board. In this technique, the component side of the board is dedicated to ground plane while signal traces are placed on the solder side. Figure 39. Coarse and Fine Adjustment –18– REV. 0 AD5334/AD5335/AD5336/AD5344 Table III. Overview of AD53xx Parallel Devices Part No. Resolution DNL VREF Pins Settling Time SINGLES AD5330 AD5331 AD5340 AD5341 8 10 12 12 ± 0.25 ± 0.5 ± 1.0 ± 1.0 1 1 1 1 6 µs 7 µs 8 µs 8 µs DUALS AD5332 AD5333 AD5342 AD5343 8 10 12 12 ± 0.25 ± 0.5 ± 1.0 ± 1.0 2 2 2 1 6 µs 7 µs 8 µs 8 µs QUADS AD5334 AD5335 AD5336 AD5344 8 10 10 12 ± 0.25 ± 0.5 ± 0.5 ± 1.0 2 2 4 4 6 µs 7 µs 7 µs 8 µs Additional Pin Functions BUF ✓ ✓ ✓ GAIN ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ Package Pins ✓ CLR ✓ ✓ ✓ ✓ TSSOP TSSOP TSSOP TSSOP 20 20 24 20 ✓ ✓ ✓ ✓ ✓ TSSOP TSSOP TSSOP TSSOP 20 24 28 20 ✓ ✓ ✓ TSSOP TSSOP TSSOP TSSOP 24 24 28 28 HBEN ✓ Table IV. Overview of AD53xx Serial Devices Part No. Resolution No. of DACS DNL Interface Settling Time Package Pins SINGLES AD5300 AD5310 AD5320 8 10 12 1 1 1 ± 0.25 ± 0.5 ± 1.0 SPI SPI SPI 4 µs 6 µs 8 µs SOT-23, MicroSOIC SOT-23, MicroSOIC SOT-23, MicroSOIC 6, 8 6, 8 6, 8 AD5301 AD5311 AD5321 8 10 12 1 1 1 ± 0.25 ± 0.5 ± 1.0 2-Wire 2-Wire 2-Wire 6 µs 7 µs 8 µs SOT-23, MicroSOIC SOT-23, MicroSOIC SOT-23, MicroSOIC 6, 8 6, 8 6, 8 DUALS AD5302 AD5312 AD5322 8 10 12 2 2 2 ± 0.25 ± 0.5 ± 1.0 SPI SPI SPI 6 µs 7 µs 8 µs MicroSOIC MicroSOIC MicroSOIC 8 8 8 AD5303 AD5313 AD5323 8 10 12 2 2 2 ± 0.25 ± 0.5 ± 1.0 SPI SPI SPI 6 µs 7 µs 8 µs TSSOP TSSOP TSSOP 16 16 16 QUADS AD5304 AD5314 AD5324 8 10 12 4 4 4 ± 0.25 ± 0.5 ± 1.0 SPI SPI SPI 6 µs 7 µs 8 µs MicroSOIC MicroSOIC MicroSOIC 10 10 10 AD5305 AD5315 AD5325 8 10 12 4 4 4 ± 0.25 ± 0.5 ± 1.0 2-Wire 2-Wire 2-Wire 6 µs 7 µs 8 µs MicroSOIC MicroSOIC MicroSOIC 10 10 10 AD5306 AD5316 AD5326 8 10 12 4 4 4 ± 0.25 ± 0.5 ± 1.0 2-Wire 2-Wire 2-Wire 6 µs 7 µs 8 µs TSSOP TSSOP TSSOP 16 16 16 AD5307 AD5317 AD5327 8 10 12 4 4 4 ± 0.25 ± 0.5 ± 1.0 SPI SPI SPI 6 µs 7 µs 8 µs TSSOP TSSOP TSSOP 16 16 16 Visit our web-page at http://www.analog.com/support/standard_linear/selection_guides/AD53xx.html REV. 0 –19– AD5334/AD5335/AD5336/AD5344 OUTLINE DIMENSIONS Dimensions shown in inches and (mm). C3830–2.5–4/00 (rev. 0) 24-Lead Thin Shrink Small Outline Package TSSOP (RU-24) 0.311 (7.90) 0.303 (7.70) 24 13 0.177 (4.50) 0.169 (4.30) 0.256 (6.50) 0.246 (6.25) 1 12 PIN 1 0.006 (0.15) 0.002 (0.05) SEATING PLANE 0.0433 (1.10) MAX 0.0256 (0.65) 0.0118 (0.30) BSC 0.0075 (0.19) 0.0079 (0.20) 0.0035 (0.090) 8ⴗ 0ⴗ 0.028 (0.70) 0.020 (0.50) 28-Lead Thin Shrink Small Outline Package TSSOP (RU-28) 0.386 (9.80) 0.378 (9.60) 28 15 0.177 (4.50) 0.169 (4.30) 0.256 (6.50) 0.246 (6.25) 1 14 PIN 1 0.006 (0.15) 0.002 (0.05) 0.0256 (0.65) BSC 0.0118 (0.30) 0.0075 (0.19) 0.0079 (0.20) 0.0035 (0.090) 8ⴗ 0ⴗ 0.028 (0.70) 0.020 (0.50) PRINTED IN U.S.A. SEATING PLANE 0.0433 (1.10) MAX –20– REV. 0