Cirrus CS5331A-KS 8-pin, stereo a/d converter for digital audio Datasheet

CS5330A/31A
8-Pin, Stereo A/D Converter for Digital Audio
Features
General Description
 Single +5 V Power Supply
The CS5330A/31A is a complete stereo analog-to-digital converter that performs anti-alias filtering, sampling
and analog-to-digital conversion generating 18-bit values for both left and right inputs in serial form. The
output sample rate can be infinitely adjusted between
2 kHz and 50 kHz.
 18-Bit Resolution
 94 dB Dynamic Range
 Linear Phase Digital Anti-Alias Filtering
–
–
0.05dB Passband Ripple
80dB Stopband Rejection
The CS5330A/31A operates from a single +5 V supply
and requires only 150 mW for normal operation, making
it ideal for battery-powered applications.
 Low Power Dissipation: 150 mW
–
Power-Down Mode for Portable
Applications
 Complete CMOS Stereo A/D System
–
–
–
Delta-Sigma A/D Converters
Digital Anti-Alias Filtering
S/H Circuitry and Voltage Reference
 Adjustable System Sampling Rates including
32kHz, 44.1 kHz & 48kHz
The ADC uses delta-sigma modulation with 128X oversampling, followed by digital filtering and decimation,
which removes the need for an external anti-alias filter.
The linear-phase digital filter has a passband to
21.7 kHz, 0.05 dB passband ripple and >80 dB stopband rejection. The device also contains a high-pass filter to remove DC offsets.
The device is available in an 8-pin SOIC package in
both Commerical (-10° to +70° C) and Automotive grades
(- 40° to +85° C). Please refer to “Ordering Information”
on page 16 for complete details.
MCLK
SCLK
LRCK
2
3
4
Voltage Reference
Serial Output Interface
AINL
8
LP Filter
S/H
Digital Decimation
Filter
High
Pass
Filter
Digital Decimation
Filter
High
Pass
Filter
Comparator
1
SDATA
DAC
AINR
5
AGND
6
LP Filter
S/H
Comparator
DAC
7
VA+
http://www.cirrus.com
Copyright © Cirrus Logic, Inc. 2006
(All Rights Reserved)
APRIL '06
DS138F5
CS5330A/31A
TABLE OF CONTENTS
1. PIN DESCRIPTIONS ................................................................................................................ 3
2. CHARACTERISTICS AND SPECIFICATIONS ........................................................................ 4
SPECIFIED OPERATING CONDITIONS ................................................................................. 4
ABSOLUTE MAXIMUM RATINGS ........................................................................................... 4
ANALOG INPUT CHARACTERISTICS .................................................................................... 5
DIGITAL CHARACTERISTICS................................................................................................. 6
DIGITAL FILTER CHARACTERISTICS ................................................................................... 6
SWITCHING CHARACTERISTICS .......................................................................................... 7
3. GENERAL DESCRIPTION ....................................................................................................... 9
3.1 System Design .................................................................................................................. 9
3.1.1 Master Clock ......................................................................................................... 9
3.1.2 Serial Data Interface ............................................................................................ 9
3.1.3 Master Mode ......................................................................................................... 9
3.1.4 Slave Mode ......................................................................................................... 10
3.1.5 CS5330A ............................................................................................................. 10
3.1.6 CS5331A ............................................................................................................. 10
3.1.7 Analog Connections ............................................................................................ 11
3.1.8 High-Pass Filter .................................................................................................. 11
3.1.9 Initialization and Power-Down ............................................................................. 11
3.1.10 Grounding and Power Supply Decoupling ........................................................ 12
3.1.11 Digital Filter ....................................................................................................... 13
4. PARAMETER DEFINITIONS .................................................................................................. 14
5. REFERENCES ........................................................................................................................ 15
6. PACKAGE DESCRIPTIONS .................................................................................................. 15
7. ORDERING INFORMATION ................................................................................................. 16
8. REVISION HISTORY .............................................................................................................. 16
LIST OF FIGURES
Figure 1.
Figure 2.
Figure 3.
Figure 4.
Figure 5.
Figure 6.
Figure 7.
Figure 8.
Typical Connection Diagram......................................................................................... 8
Data Output Timing-CS5330A .................................................................................... 10
Data Output Timing - CS5331A (I²S Compatible) ....................................................... 10
CS5330A/31A Initialization and Power-Down Sequence............................................ 12
CS5330A/31A Digital Filter Stopband Rejection......................................................... 13
CS5330A/31A Digital Filter Transition Band ............................................................... 13
CS5330A/31A Digital Filter Passband Ripple ............................................................. 13
CS5330A/31A Digital Filter Transition Band ............................................................... 13
LIST OF TABLES
Table 1.
2
Common Clock Frequencies......................................................................................... 9
DS138F5
CS5330A/31A
1. PIN DESCRIPTIONS
SERIAL DATA OUTPUT
SDATA
1
8
AINL
LEFT ANALOG INPUT
SERIAL DATA CLOCK
SCLK
2
7
VA+
ANALOG POWER
LEFT/RIGHT CLOCK
LRCK
3
6
AGND
ANALOG GROUND
MASTER CLOCK
MCLK
4
5
AINR
RIGHT ANALOG INPUT
Pin Name
#
Pin Description
SDATA
1
Audio Serial Data Output (Output) - Two’s complement MSB-first serial data is output on this
pin. A 47 kΩ resistor on this pin will place the CS5330A/31A into Master Mode.
SCLK
2
Serial Data Clock (Input/Output) - SCLK is an input clock at any frequency from 32x to 64x the
output word rate. SCLK can also be an output clock at 64x if in the Master Mode. Data is
clocked out on the falling edge of SCLK.
LRCK
3
Left/Right Clock (Input/Output) - LRCK selects the left or right channel for output on SDATA.
The LRCK frequency must be at the output sample rate. LRCK is an output clock if in Master
Mode. Although the outputs of each channel are transmitted at different times, the two words in
an LRCK cycle represent simultaneously sampled analog inputs.
MCLK
4
Master Clock Input (Input) - Source for the delta-sigma modulator sampling and digital filter
clock. Sample rates and digital filter characteristics scale to the MCLK frequency.
AINR
5
Analog Right Channel Input (Input) - Analog input for the right channel. Typically 4 Vpp for a
full-scale input signal.
AGND
6
Analog Ground (Input) - Analog ground reference.
VA+
7
Positive Analog Power (Input) - Positive analog supply (Nominally +5 V).
AINL
8
Analog Left Channel Input (Input) - Analog input for the left channel. Typically 4 Vpp for a fullscale input signal.
DS138F5
3
CS5330A/31A
2. CHARACTERISTICS AND SPECIFICATIONS
(All Min/Max characteristics and specifications are guaranteed over the Specified Operating Conditions. Typical
performance characteristics and specifications are derived from measurements taken at nominal supply voltages
and TA = 25°C.)
SPECIFIED OPERATING CONDITIONS
(AGND = 0V, all voltages with respect to ground)
Parameter
Analog Supply Voltage
Ambient Operating Temperature (Power Applied)
KS, KSZ
BS, DS
Symbol
Min
Typ
Max
Unit
VA+
4.75
5.0
5.25
V
TA
-10
-40
-
+70
+85
°C
°C
ABSOLUTE MAXIMUM RATINGS
(AGND = 0V, all voltages with respect to ground.) (Note 1)
Parameter
Analog Supply Voltage
Symbol
Min
Typ
Max
Unit
VA+
-0.3
-
+6.0
V
Input Current, Any Pin Except Supplies
(Note 2)
lin
-
-
±10
mA
Analog Input Voltage
(Note 3)
VINA
-0.7
-
VA+0.7
V
Digital Input Voltage
(Note 3)
VIND
-0.7
-
VA+0.7
V
Ambient Temperature (power applied)
TA
-55
-
+125
°C
Storage Temperature
Tstg
-65
-
+150
°C
Notes:
1. Operation at or beyond these limits may result in permanent damage to the device. Normal operation
is not guaranteed at these extremes.
2. Any Pin except supplies. Transient current of up to +/- 100 mA on the analog input pins will not cause
SCR latch-up.
3. The maximum over/under voltage is limited by the input current.
4
DS138F5
CS5330A/31A
ANALOG INPUT CHARACTERISTICS
(-1 dBFS Input Sinewave, 997 Hz; Measurement Bandwidth is 10 Hz to 20 kHz unless otherwise specified; Logic
0 = 0V, Logic 1 = VD+)
Parameter
Dynamic Performance
Dynamic Range
5330A/31A-KS/KSZ
Symbol Min
Typ
Max
A-weighted
unweighted
Total Harmonic Distortion + Noise
(Note 4)
-1 dB
THD+N
-20 dB
-60 dB
Total Harmonic Distortion
-1 dB
Interchannel Phase Deviation
Interchannel Isolation
(dc to 20 kHz)
DC Accuracy
Interchannel Gain Mismatch
Gain Error
Gain Drift
Offset Error
(Note 5)
Analog Input
Full-scale Input Voltage
Input Impedance
(Fs = 48 kHz)
Input Bias Voltage
Power Supplies
Power Supply Current
VA+
THD
5331A-DSZ
Typ
Max
Unit
88
86
94
92
-
86
84
94
92
-
dB
dB
-
-84
-72
-32
75
66
26
-
-84
-72
-32
75
66
26
dB
dB
dB
-
0.003
0.02
-
0.003
0.2
%
-
0
-
-
0
-
Degree
-
90
-
-
90
-
dB
-
0.1
-
-
0.1
-
dB
-
-
±10
-
-
±10
%
-
150
-
-
150
-
ppm/°C
-
-
0
-
-
0
LSB
VIN
3.6
4.0
4.4
3.6
4.0
4.4
Vpp
ZIN
-
100
-
-
100
-
kΩ
2.2
2.4
2.6
2.2
2.4
2.6
V
-
30
100
42
1000
-
30
100
42
1000
mA
µA
-
150
0.5
220
5.25
-
150
0.5
220
5.25
mW
mW
-
-
50
-
dB
IA+
Power down
Power Dissipation
Min
Normal
Power down
PSRR
50
Power Supply Rejection Ratio
* Refer to Parameter Definitions at the end of this data sheet.
4. Referenced to typical full-scale input voltage.
5. Internal highpass filter removes offset.
DS138F5
5
CS5330A/31A
DIGITAL CHARACTERISTICS
Parameter
Symbol
Min
Typ
Max
Unit
High-Level Input Voltage
VIH
2.4
-
-
V
Low-Level Input Voltage
VIL
-
-
0.8
V
High-Level Output Voltage at lo = -20 µA
VOH
VA-1.0
-
-
V
Low-Level Output Voltage at lo = 20 µA
VOL
-
-
0.4
V
Iin
-
-
±10.0
µA
Input leakage Current
DIGITAL FILTER CHARACTERISTICS
(FS = 48 kHz)
Parameter
Passband
(0.05)
Symbol
(Note 6)
Passband Ripple
Stopband
(Note 6)
Stopband Attenuation
(Note 7)
Group Delay
(Note 8)
Min
Typ
Max
Unit
0.02
-
21.7
kHz
-
-
±0.05
dB
29
-
6115
kHz
80
-
-
dB
tgd
-
15/Fs
-
s
∆tgd
-
-
0
µs
(Note 6)
-
3.7
20
-
Hz
Hz
(Note 6)
-
10
-
Degree
-
-
0
dB
Group Delay Variation vs. Frequency
High Pass Filter Characteristics
Frequency Response:
Phase Deviation
-3 dB
-0.1 dB
@ 20 Hz
Passband Ripple
6. Filter characteristics scale with output sample rate.
7. The analog modulator samples the input at 6.144 MHz for an output sample rate of 48 kHz. There is no
rejection of input signals which are multiples of the sampling frequency (n x 6.144 MHz ±21.7 kHz where
n = 0,1,2,3…).
8. Group delay for Fs = 48 kHz, tgd = 15/48 kHz = 312µs.
6
DS138F5
CS5330A/31A
SWITCHING CHARACTERISTICS
(Inputs: Logic 0 = 0V, Logic 1 = VA+; CL = 20 pF) Switching characteristics are guaranteed by characterization.
Parameter
Symbol
Min
Typ
Max
Unit
Fs
2
-
50
kHz
clkw
78
-
1000
ns
MCLK/LRCK = 256
t
clkl
31
-
1000
ns
MCLK/LRCK = 256
t
clkh
31
-
1000
ns
MCLK/LRCK = 384
t
clkw
52
-
1000
ns
MCLK/LRCK = 384
t
clkl
20
-
1000
ns
MCLK/LRCK = 384
t
clkh
20
-
1000
ns
MCLK/LRCK = 512
t
Output Sample Rate
MCLK Period
MCLK Low
MCLK High
MCLK Period
MCLK Low
MCLK High
MCLK Period
MCLK/LRCK = 256
t
clkw
39
-
1000
ns
clkl
13
-
1000
ns
clkh
13
-
1000
ns
MCLK Low
MCLK/LRCK = 512
t
MCLK High
MCLK/LRCK = 512
t
MASTER MODE
SCLK falling to LRCK
tmslr
-10
-
10
ns
SCLK falling to SDATA valid
tsdo
-10
-
35
ns
-
50
-
%
SCLK Duty cycle
SLAVE MODE
LRCK duty cycle
25
50
75
%
tclkw
(Note 9)
-
-
ns
SCLK Pulse Width Low
tclkl
(Note 10)
-
-
ns
SCLK Pulse Width High
tclkh
20
-
-
ns
SCLK falling to SDATA valid
tdss
-
-
(Note 11)
ns
tlrdss
-
-
(Note 11)
ns
SCLK rising to LRCK edge delay
tslr1
20
-
-
ns
LRCK edge to rising SCLK setup time
tslr2
(Note 11)
-
-
ns
SCLK Period
LRCK edge to MSB valid
9.
1
64 Fs
10.
1
- 15 ns
128 Fs
11.
1
+ 5 ns
256 Fs
DS138F5
7
CS5330A/31A
SCLK output
SCLK output
t mslr
t mslr
LRCK output
LRCK output
t sdo
t sdo
SDATA
SDATA
SCLK to SDATA LRCK - MASTER mode (CS5331A)
SCLK to SDATA LRCK - MASTER mode (CS5330A)
t slr1 t slr2
t slr1 t slr2
t sclkl t sclkh
SCLK input
(SLAVE mode)
t sclkl t sclkh
SCLK input
(SLAVE mode)
t sclkw
t sclkw
LRCK input
(SLAVE mode)
LRCK input
(SLAVE mode)
t lrdss
t dss
MSB
SDATA
MSB-1
t dss
MSB-2
SCLK to LRCK & SDATA - SLAVE mode (CS5330A)
+5V
Analog
10 µF
MSB
SDATA
MSB-1
SCLK to LRCK & SDATA - SLAVE mode (CS5331A)
0.1 µF
+
7
VA+
150 Ω
.47 µF
**
Analog
Input
Circuits
150 Ω
8
AINL
.01 µF
CS5330A
CS5331A
.47 µF
**
Audio Data
Processor
5
MCLK
SCLK
LRCK
AINR
.01 µF
SDATA
4
1 kΩ
2
1 kΩ
3
1 kΩ
1
1 kΩ
*
Timing
Logic
&
Clock
47 kΩ
AGND
* Required for Master mode only
** Optional if analog input circuits biased
to within ± 5% of CS5330A/CS5331A
nominal input bias voltage
6
Figure 1. Typical Connection Diagram
8
DS138F5
CS5330A/31A
3. GENERAL DESCRIPTION
The CS5330A and CS5331A are 18-bit, 2-channel Analog-to-Digital Converters designed for digital audio applications. Each device uses two one-bit delta-sigma modulators which simultane-ously sample the analog input signals
at 128 times the output sample rate (Fs). The resulting serial bit streams are digitally filtered, yielding pairs of 18-bit
values. This technique yields nearly ideal conversion performance independent of input frequency and amplitude.
The converters do not require difficult-to-design or expensive anti-alias filters and do not require external sampleand-hold amplifiers or a voltage reference.
The CS5330A and CS5331A differ only in the output serial data format. These formats are dis-cussed in the following sections and shown in Figures 2 and 3.
An on-chip voltage reference provides for a single-ended input signal range of 4.0 Vpp. Output data is available in
serial form, coded as 2’s complement 18-bit numbers. Typical power con-sumption is 150 mW which can be further
reduced to 0.5 mW using the Power-Down mode.
For more information on delta-sigma modulation, see the references at the end of this data sheet.
3.1
System Design
Very few external components are required to support the ADC. Normal power supply decou-pling components and a resistor and capacitor on each input for anti-aliasing are all that’s required, as shown in Figure 1.
3.1.1
Master Clock
The master clock (MCLK) runs the digital filter and is used to generate the delta-sigma modula-tor sampling clock. Table 1 shows some common master clock frequencies. The output sample rate is equal to
the frequency of the Left / Right Clock (LRCK). The serial nature of the output data results in the left and
right data words being read at different times. However, the words within an LRCK cycle represent simultaneously sampled analog inputs. The serial clock (SCLK) shifts the digitized audio data from the internal
data registers via the SDATA pin.
3.1.2
Serial Data Interface
LRCK
(kHz)
MCLK (MHz)
256x
384x
512x
32
8.1920
12.2880
16.3840
44
11.2896
16.9344
22.5792
48
12.2880
18.4320
24.5760
Table 1. Common Clock Frequencies
The CS5330A and CS5331A can be operated in either Master mode, where SCLK and LRCK are outputs,
or SLAVE mode, where SCLK and LRCK are inputs.
3.1.3
Master Mode
In Master mode, SCLK and LRCK are outputs which are internally derived from MCLK. The CS5330A/31A
will divide MCLK by 4 to generate a SCLK which is 64× Fs and by 256 to generate LRCK. The CS5330A
and CS5331A can be placed in the Master mode with a 47 kohm pull-down resistor on the SDATA pin as
shown in Figure 1.
DS138F5
9
CS5330A/31A
3.1.4
Slave Mode
LRCK and SCLK become inputs in SLAVE mode. LRCK must be externally derived from MCLK and be
equal to Fs. The frequency of SCLK should be equal to 64x LRCK, though other frequencies are possible.
MCLK frequencies of 256x, 384x, and 512x Fs are supported. The ratio of the applied MCLK to LRCK is
automatically detected during power-up and internal dividers are set to generate the ap-propriate internal
clocks.
3.1.5
CS5330A
The CS5330A data output format is shown in Figure 2. Notice that the MSB is clocked by the transition of
LRCK and the remaining seventeen data bits are clocked by the falling edge of SCLK. The data bits are
valid during the rising edge of SCLK.
3.1.6
CS5331A
The CS5331A data output format is shown in Figure 3. Notice the one SCLK period delay be-tween the
LRCK transitions and the MSB of the data. The falling edges of SCLK cause the ADC to output the eighteen data bits. The data bits are valid during the rising edge of SCLK. LRCK is also inverted compared to
the CS5330A interface. The CS5331A interface is compatible with I2S.
LRCK
0
1
17
2
18 19 20 21
22
30 31
0
1
17
2
18 19 20 21
22 23
31
0
1
SCLK
SDATA
17 16
1
0
17 16
Left Audio Data
1
0
Right Audio Data
Figure 2. Data Output Timing-CS5330A
LRCK
0
1
2
3
18 19 20 21
22
30 31
0
1
2
18 19 20 21
3
22 23
31
0
1
SCLK
SDATA
17 16
1
Left Audio Data
0
17 16
1
0
Right Audio Data
Figure 3. Data Output Timing - CS5331A (I²S Compatible)
10
DS138F5
CS5330A/31A
3.1.7
Analog Connections
Figure 1 shows the analog input connections. The analog inputs are presented to the modula-tors via the
AINR and AINL pins. Each analog input will accept a maximum of 4 Vpp centered at +2.4 V.
The CS5330A/31A samples the analog inputs at 128 × Fs, 6.144 MHz for a 48 kHz sample-rate. The digital filter rejects all noise above 29 kHz except for frequencies right around 6.144 MHz ±21.7 kHz (and
multiples of 6.144 MHz). Most audio signals do not have significant energy at 6.144 MHz. Nevertheless,
a 150 Ω resistor in series with each analog input and a 10 nF capacitor across the inputs will attenuate
any noise energy at 6.144 MHz, in addition to providing the optimum source impedance for the modulators. The use of capacitors which have a large voltage coefficient must be avoided since these will degrade signal linearity. It is also important that the self-resonant frequency of the capacitor be well above
the modulator sampling frequency. General purpose ceramics and film capacitors do not meet these requirements. However, NPO and COG capacitors are acceptable. If active circuitry precedes the ADC, it
is recom-mended that the above RC filter is placed between the active circuitry and the AINR and AINL
pins. The above example frequencies scale linearly with Fs.
3.1.8
High-Pass Filter
The operational amplifiers in the input circuitry driving the CS5330A/31A may generate a small DC offset
into the A/D converter. The CS5330A/31A includes a high pass filter after the decimator to remove any
DC offset which could result in recording a DC level, possibly yielding "clicks" when switching between
de-vices in a multichannel system.
The characteristics of this first-order high pass filter are outlined in the “Digital Filter Characteristics” on
page 6
3.1.9
Initialization and Power-Down
The Initialization and Power-Down sequence is shown in Figure 4. Upon initial power-up, the digital filters
and delta-sigma modulators are reset and the internal voltage reference is powered down. The device will
remain in the Initial Power-Down mode until MCLK is presented. Once MCLK is available, the
CS5330A/31A will make a master/slave mode decision based upon the presence/absence of a 47 kohm
pull-down resistor on SDATA as shown in Figure 1. The master/slave decision is made during initial power-up as shown in Figure 4.
In master mode, SCLK and LRCK are outputs where the MCLK/LRCK frequency ratio is 256x. LRCK will
appear as an output 127 MCLK cycles into the initialization sequence. At this time, power is applied to the
internal voltage reference and the analog inputs will move to approximately 2.4 Volts. SDATA is static low
during the initialization and high pass filter settling sequence, which requires 11,265 LRCK cycles (235
ms at a 48 kHz output sample rate).
In slave mode, SCLK and LRCK are inputs where the MCLK/LRCK frequency ratio must be either 256x,
384x, or 512x. Once the MCLK and LRCK are detected, MCLK occurrences are counted over one LRCK
period to determine the MCLK/LRCK frequency ratio. At this time, power is applied to the internal voltage
reference and the analog inputs will move to approximately 2.4 Volts. SDATA is static high during the initialization and high pass filter settling sequence, which requires 11,265 LRCK cycles (235 ms at a 48 kHz
sample rate).
DS138F5
11
CS5330A/31A
USER: Apply Power
Initia
l Power
-Down
USER: Apply
MCLK
MasterMode
Master/Slave
Decision
MasterMode
PowerDown
USER: Re
move
MCLK
MCLK/LRCK Rati
o
is 256xo
nly
Slave Mode
Slave Mode
PowerDown
USER: Apply
MCLK
and LRCK
MCLK/LRCK Rati
o
Determinati
on
USER: Re
move
256/384/512
MCLK,LRCK or
Both
Initia
lizati
on
-High p
assfiltersettin
gs
- SDATA mute rele
ased
Initia
lizati
on
-High p
assfiltersettin
g
- SDATA mute rele
ased
Digita
lOutput
is generat
ed
Digita
lOutput
is Generat
ed
Figure 4. CS5330A/31A Initialization and Power-Down Sequence
The CS5330A and CS5331A have a Power-Down mode wherein typical consumption drops to 0.5 mW.
This is initiated when a loss of clock is detected on either the LRCK or MCLK pins in Slave Mode, or the
MCLK pin in Master Mode. The initialization sequence will begin when MCLK, and LRCK for slave mode,
are restored. In slave mode power-down, the CS5330A and CS5331A will adapt to changes in
MCLK/LRCK frequency ratio during the initialization sequence. It is recommended that clocks not be applied to the device prior to power supply settling. A reset circuit may be implemented by gating the MCLK
signal.
3.1.10 Grounding and Power Supply Decoupling
As with any high resolution converter, the ADC requires careful attention to power supply and grounding
arrangements if its potential performance is to be realized. Figure 1 shows the recommended power arrangements with VA+ connected to a clean +5V supply. Decoupling capacitors should be as near to the
ADC as possible, with the low value ceramic capacitor being the nearest. To minimize digital noise, connect the ADC digital outputs only to CMOS inputs. The printed circuit board layout should have separate
analog and digital regions and ground planes. An evaluation board, CDB5330A or CDB5331A, is available which demonstrates the optimum layout and power supply arrangements, as well as allowing fast
evaluation of the CS5330A and CS5331A.
12
DS138F5
CS5330A/31A
3.1.11
Digital Filter
Figures 5 through 8 show the attenuation characteristics of the digital filter included in the ADC. The filter
response scales linearly with sample rate. The x-axis has been normalized to Fs, and can be scaled by
multiplying the x-axis by the system sample rate, i.e. 48 kHz.
0
2
-10
0
-20
-30
-2
Magnitude (dB)
-40
-50
-60
-70
-80
-90
-4
-6
-8
-100
-110
-120
0.0
-10
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
.46
1.0
.47
Normalized Input Frequency
.48
.49
.50
.51
.52
.53
.54
Normalized Input Frequency
Figure 5. CS5330A/31A Digital Filter Stopband Rejection
Figure 6. CS5330A/31A Digital Filter Transition Band
0.05
0.0
0.04
-10.0
0.03
-20.0
0.02
-30.0
0.01
-40.0
0.00
-50.0
-0.01
-60.0
-0.02
-70.0
-0.03
-80.0
-0.04
-90.0
-100.0
-0.05
0
0.1
0.2
0.3
0.4
0.5
Normalized Input Frequency
Figure 7. CS5330A/31A Digital Filter Passband Ripple
DS138F5
0.40
0.45
0.50
0.60
0.65
0.70
Normalized Input Frequency
Figure 8. CS5330A/31A Digital Filter Transition Band
13
CS5330A/31A
4. PARAMETER DEFINITIONS
Resolution
The total number of possible output codes is equal to 2 N, where N = the number of bits in the output word
for each channel.
Dynamic Range
The ratio of the full-scale rms value of the signal to the rms sum of all other spectral components over the
specified bandwidth. Dynamic range is a signal-to-noise measurement over the specified bandwidth made
with a -60 dBFS signal. 60 dB is then added to the resulting measurement to refer the measurement to full
scale. This technique ensures that the distortion components are below the noise level and do not effect the
measurement. This measurement technique has been accepted by the Audio Engineering Society, AES171991, and the Electronic Industries Association of Japan, EIAJ CP-307.
Total Harmonic Distortion+Noise (THD+N)
The ratio of the rms value of the signal to the rms sum of all other spectral components over the specified
band width (typically 10 Hz to 20 kHz), including distortion components. Expressed in decibels. Measured
at -1 and -20 dBFS as suggested in AES17-1991 Annex A.
Total Harmonic Distortion
The ratio of the rms sum of all harmonics up to 20 kHz to the rms value of the signal.
Interchannel Phase Deviation
The phase difference between the left and right channel sampling times.
Interchannel Isolation
A measure of crosstalk between the left and right channels. Measured for each channel at the converter’s
output with the input under test AC grounded and a full-scale signal applied to the other channel. Units in
decibels.
Interchannel Gain Mismatch
The gain difference between left and right channels. Units in decibels.
Gain Error
The deviation of the measured full-scale amplitude from the ideal full-scale amplitude value.
Gain Drift
The change in gain value with temperature. Units in ppm/°C.
Bipolar Offset Error
The deviation of the mid-scale transition (111...111 to 000...000) from the ideal. Units in LSBs.
14
DS138F5
CS5330A/31A
5. REFERENCES
1. Area Efficient Decimation Filter for an 18-Bit Delta- Sigma ADC, by K. Lin and J.J. Paulos. Paper presented
at the 98th Convention of the Audio Engineering Society, February 1995.
2. An 18-Bit, 8-Pin Stereo Digital-to-Analog Converter, by J.J. Paulos, A.W. Krone, G.D. Kamath and S.T. Dupuie. Paper presented at the 97th Convention of the Audio Engineering Society, November 1994.
3. An 18-Bit Dual-Channel Oversampling Delta-Sigma A/D Converter, with 19-Bit Mono Application Example,
by Clif Sanchez. Paper presented at the 87th Convention of the Audio Engineering Society, October 1989.
4. The Effects of Sampling Clock Jitter on Nyquist Sampling Analog-to-Digital Converters, and on Oversampling Delta Sigma ADC’s, by Steven Harris. Paper presented at the 87th Convention of the Audio Engineering Society, October 1989.
5. A Stereo 16-bit Delta-Sigma A/D Converter for Digital Audio, by D.R. Welland, B.P. Del Signore, E.J. Swanson, T. Tanaka, K. Hamashita, S. Hara, K. Takasuka. Paper presented at the 85th Convention of the Audio
Engineering Society, November 1988.
6. PACKAGE DESCRIPTIONS
A
8-Pin
SOIC
B
E
D
C
G
F
H
I
J
DIM
A
B
C
D
E
F
G
H
I
J
Millimeters
MIN
MAX
5.15
5.35
1.27 TYP
0
0.25
1.77
1.88
0.33
0.51
.15
0.25
0°
8°
5.18
5.4
0.48
0.76
7.67
8.1
Inches
MIN
0.203
0.050
0
0.070
0.013
0.006
0°
0.204
0.019
0.302
MAX
0.210
TYP
0.010
0.074
0.020
0.010
8°
0.213
0.030
0.319
Note: The EIAJ Package is not a standard JEDEC package size.
DS138F5
15
CS5330A/31A
7. ORDERING INFORMATION
Product
CS5330A
CS5331A
CS5330A
CS5331A
CS5330A
CS5331A
Description
8-pin, Stereo A/D Converter for Digital Audio
8-pin, Stereo A/D Converter for Digital Audio
8-pin, Stereo A/D Converter for Digital Audio
8-pin, Stereo A/D Converter for Digital Audio
8-pin, Stereo A/D Converter for Digital Audio
8-pin, Stereo A/D Converter for Digital Audio
Package
Pb-Free
Grade
Temp Range
8-SOIC
NO
Commercial -10° to +70° C
8-SOIC
NO
Commercial -10° to +70° C
8-SOIC
YES
Commercial -10° to +70° C
8-SOIC
YES
Commercial -10° to +70° C
8-SOIC
NO
Automotive -40° to +85° C
8-SOIC
YES
Automotive -40° to +85° C
Container
Order #
Bulk
CS5330A-KS
Tape & Reel CS5330A-KSR
Bulk
CS5331A-KS
Tape & Reel CS5331A-KSR
Bulk
CS5330A-KSZ
Tape & Reel CS5330A-KSZR
Bulk
CS5331A-KSZ
Tape & Reel CS5331A-KSZR
Bulk
CS5330A-BS
Tape & Reel CS5330A-BSR
Bulk
CS5331A-DSZ
Tape & Reel CS5331A-DSZR
8. REVISION HISTORY
Release
F5
Changes
Updated Ordering Information
Contacting Cirrus Logic Support
For all product questions and inquiries, contact a Cirrus Logic Sales Representative.
To find the one nearest to you, go to www.cirrus.com.
IMPORTANT NOTICE
Cirrus Logic, Inc. and its subsidiaries ("Cirrus") believe that the information contained in this document is accurate and reliable. However, the information is subject
to change without notice and is provided "AS IS" without warranty of any kind (express or implied). Customers are advised to obtain the latest version of relevant
information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale
supplied at the time of order acknowledgment, including those pertaining to warranty, indemnification, and limitation of liability. No responsibility is assumed by Cirrus
for the use of this information, including use of this information as the basis for manufacture or sale of any items, or for infringement of patents or other rights of third
parties. This document is the property of Cirrus and by furnishing this information, Cirrus grants no license, express or implied under any patents, mask work rights,
copyrights, trademarks, trade secrets or other intellectual property rights. Cirrus owns the copyrights associated with the information contained herein and gives consent for copies to be made of the information only for use within your organization with respect to Cirrus integrated circuits or other products of Cirrus. This consent
does not extend to other copying such as copying for general distribution, advertising or promotional purposes, or for creating any work for resale.
CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE (“CRITICAL APPLICATIONS”). CIRRUS PRODUCTS ARE NOT DESIGNED, AUTHORIZED OR WARRANTED FOR USE
IN AIRCRAFT SYSTEMS, MILITARY APPLICATIONS, PRODUCTS SURGICALLY IMPLANTED INTO THE BODY, AUTOMOTIVE SAFETY OR SECURITY DEVICES, LIFE SUPPORT PRODUCTS OR OTHER CRITICAL APPLICATIONS. INCLUSION OF CIRRUS PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO BE FULLY AT THE CUSTOMER’S RISK AND CIRRUS DISCLAIMS AND MAKES NO WARRANTY, EXPRESS, STATUTORY OR IMPLIED,
INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR PARTICULAR PURPOSE, WITH REGARD TO ANY CIRRUS PRODUCT
THAT IS USED IN SUCH A MANNER. IF THE CUSTOMER OR CUSTOMER’S CUSTOMER USES OR PERMITS THE USE OF CIRRUS PRODUCTS IN CRITICAL
APPLICATIONS, CUSTOMER AGREES, BY SUCH USE, TO FULLY INDEMNIFY CIRRUS, ITS OFFICERS, DIRECTORS, EMPLOYEES, DISTRIBUTORS AND
OTHER AGENTS FROM ANY AND ALL LIABILITY, INCLUDING ATTORNEYS’ FEES AND COSTS, THAT MAY RESULT FROM OR ARISE IN CONNECTION
WITH THESE USES.
Cirrus Logic, Cirrus, and the Cirrus Logic logo designs are trademarks of Cirrus Logic, Inc. All other brand and product names in this document may be trademarks
or service marks of their respective owners.
16
DS138F5
Similar pages