THE CONNOR-WINFIELD CORP. 2111 COMPREHENSIVE DRIVE. AURORA, IL 60505. FAX (630) 851-5040. PHONE (630) 851-4722. www.conwin.com PRODUCT D ATA SHEET CRYSTAL CONTROLLED OSCILLATORS ABSOLUTE MAXIMUM RATINGS CW 0107 ASOV5S3 12.80M SURFACE MOUNT 5.0V HCMOS STRATUM 3 OCXO TABLE 1.0 PARAMETER Storage Temperature Supply Voltage Control Voltage UNITS MINIMUM NOMINAL MAXIMUM UNITS (Vcc) (Vc) -40 -0.5 -0.5 - 85 7.0 7.0 °C Vdc Vdc OPERATING SPECIFICATIONS NOTE TABLE 2.0 PARAMETER Center Frequency (Fo) MINIMUM 1.544 Frequency Calibration, Vc=2.18 Vdc NOMINAL MAXIMUM UNITS - 20.0 1.5 MHz ppm 1 -0.25 -30 -2.5 -4.6 0 - 0.25 30 2.5 4.6 70 ppm ppb ppm ppm °C 2 3 Vdc -1.5 Frequency Stability Aging (Daily) Aging (20 Years) Total Frequency Tolerance Operating Temperature Range NOTE 4 Supply Voltage (Vcc) 4.75 5.0 5.25 Supply Current (Icc) - - 350 mA Phase Jitter (BW=12KHz to 20MHz) - - 1 ps rms Phase Jitter (BW=10Hz to 20MHz) - - 3 ps rms Period Jitter SSB Phase Noise at 10Hz offset SSB Phase Noise at 10KHz offset Start Up Time: Oscillator Warm Up Time TDEV @ 1.0 Sec. TDEV @ 4.0 Sec. - -90 -135 - 3 10 5 1 2 ps rms dBc/Hz dBc/Hz mS Minutes nS nS MINIMUM NOMINAL MAXIMUM UNITS 0.5 2.18 4.1 Vdc Frequency at Vc=0.3 Vdc -30 - -18 ppm 6 Frequency at Vc=3.0 Vdc 18 - 30 ppm 6 5 - - ppm/V 100k - - Ohm INTPUT CHARACTERISTICS ASOV5S3 5 DESCRIPTION The Connor-Winfield ASOV5S3 is a true Surface Mount 5.0V Oven Controlled Crystal Oscillator (OCXO) with an HCMOS output. The ASOV5S3 is designed for Stratum 3 applications requiring tight frequency stability and low jitter. TABLE 3.0 PARAMETER Control Voltage Range (Vc) Slope of Frequency Adjust Input Impedance NOTE FEATURES FREQUENCY ADJUST 5.0V OPERATION LOW JITTER <1pS RMS HCMOS OUTPUT CHARACTERISTICS TABLE 4.0 PARAMETER LOAD Voltage (High) (Low) Current (High) (Low) Duty Cycle at 50% of Vcc Rise / Fall Time 10% to 90% PACKAGE CHARACTERISTICS Package PROCESS RECOMMENDATIONS Solder Reflow Wash MINIMUM NOMINAL MAXIMUM UNITS 4.5 -4 45 - - 15 0.4 4 55 6 pf Vdc Vdc mA mA % nS (Voh) (Vol) (Ioh) (Ioh) 50 - NOTE TEMPERATURE STABILITY ±0.25ppm FREQUENCY TOLERANCE OF ±4.6ppm OVER TWENTY YEARS SURFACE MOUNT PACKAGE TABLE 5.0 Surface Mount, Non-hermetic package consisting of an FR4 substrate with grounded metal cover. TABLE 6.0 The component solder used internal to this device has a mel ting point of 221°C. The peak temperature inside the device should be less than or equal to 220°C for a maximum of 10 seconds Ultrasonic cleaning is not recommended TAPE AND REEL PACKAGING ORDERING INFORMATION Notes: 1) 2) 3) 4) Initial calibration @ 25°C, Vc=2.18 Vdc. Frequency vs. temperature stability At the time of shipment after48 hours of operation. Inclusive of calibration, operating temperature range, supply voltage change, load change, shock and vibration, 20 years aging, Vc=2.18 Vdc. 5) Measured @ 25°C, within 5 minutes, the unit will be within +/-0.1ppm of its reference frequency, measured after 30 minutes of continuous operation at a stable 25°C 6) Referenced to Fo @ 25°C, Positive Transfer Characteristic ASOV5S3 - 12.80MHz OCXO SERIES CENTER FREQUENCY Specifications subject to change without notice. DATA SHEET #: Cx016 PAGE 1 OF 2 REV: 04 DATE: 6/24/03 aCopyright 2001 Connor-Winfield all rights reserved. THE CONNOR-WINFIELD CORP. 2111 COMPREHENSIVE DRIVE. AURORA, IL 60505. FAX (630) 851-5040. PHONE (630) 851-4722. www.conwin.com PRODUCT D ATA SHEET CRYSTAL CONTROLLED OSCILLATORS ENVIRONMENTAL CHARACTERISTICS Temperature Cycle: Per MIL-STD-883, Method 1010, Condition B. -55°C to 125°C, 20 cycles,10 minute dwell, 1m inute transition. SOLDERING Pad Solderability: Per MIL-STD-883, Method 200. 8 hour steam age prior to 254°C ±5°C Solder pot dip, 95% Coverage. Solder Reflow: The component solder internal to this device has a melt ing point of 221°C, the peak temperature inside the device should be less than or equal to 220°C for a maximum of 10 seconds. MECHANICAL CHARACTERISTICS Vibration: Per MIL-STD-202, Method 204, Condition A. 10G’s peak, 10Hz to 500Hz, 15mi nute cycles 12 times each perpendicular axis. Shock: Per MIL-STD-202, Method 213, Condition D. 500G’s, 1ms, half sine, 3 shocks per direction. Moisture Resistance: Per MIL-STD-202, Method 106. 95% RH @ 65°C, 10 cycles 10°C to 65°C. PIN FUNCTION .330 max (8.382mm) CW DATE CODE ASOV5S3 12.80M 1 7 8 14 CONTROL VOLTAGE GROUND (CASE) OUTPUT Vcc Dimensional Tolerance: ±.005 (.127mm) KEEP OUT AREA 90% .830 (21.08mm) 50% 10% .565 (14.35mm) CONTROL VOLTAGE 4.1Vdc POWER SUPPLY 5.0Vdc 14 8 1 7 Specifications subject to change without notice. DATA SHEET #: Cx016 PAGE 2 OF 2 REV: 04 DATE: 6/24/03 aCopyright 2001 Connor-Winfield all rights reserved.