ACSL-6xx0 Multi-Channel and Bi-Directional, 15 MBd Digital Logic Gate Optocoupler Data Sheet Lead (Pb) Free RoHS 6 fully compliant RoHS 6 fully compliant options available; -xxxE denotes a lead-free product Description Features ACSL-6xx0 are truly isolated, multi-channel and bi-directional, high-speed optocouplers. Integration of multiple optocouplers in monolithic form is achieved through patented process technology. These devices provide full duplex and bi‑directional isolated data transfer and communication capability in compact surface mount packages. Available in 15 Mbd speed option and wide supply voltage range. • Available in dual, triple and quad channel configurations • Bi-directional • Wide supply voltage range: 3.0V to 5.5V • High-speed: 15 MBd typical, 10 MBd minimum • 10 kV/µs minimum Common Mode Rejection (CMR) at Vcm = 1000V • LSTTL/TTL compatible • Safety and regulatory approvals – 2500Vrms for 1 min per UL1577 – cUL (CSA Component Acceptance Notice 5A) – IEC/EN/DIN EN 60747-5-5 • 16 Pin narrow-body SOIC package for triple and quad channel • -40 to 100°C temperature range These high channel density make them ideally suited to isolating data conversion devices, parallel buses and peripheral interfaces. They are available in 8-pin and 16–pin narrow-body SOIC package and are specified over the temperature range of -40°C to +100°C. Applications • • • • • • • • Serial Peripheral Interface (SPI) Inter-Integrated Interface (I2C) Full duplex communication Isolated line receiver Microprocessor system interfaces Digital isolation for A/D and D/A conversion Instrument input/output isolation Ground loop elimination CAUTION: It is advised that normal static precautions be taken in handling and assembly of this component to prevent damage and/or degradation, which may be induced by ESD. Device Selection Guide Device Number Channel Configuration Package ACSL-6210 Dual, Bi-Directional` 8-pin Small Outline ACSL-6300 Triple, All-in-One 16-pin Small Outline ACSL-6310 Triple, Bi-Directional, 2/1 16-pin Small Outline ACSL-6400 Quad, All-in-One 16-pin Small Outline ACSL-6410 Quad, Bi-Directional, 3/1 16-pin Small Outline ACSL-6420 Quad, Bi-Directional, 2/2 16-pin Small Outline Ordering Information ACSL-6xx0 is UL Recognized with 2500 Vrms for 1 minute per UL1577 and is approved under CSA Component Acceptance Notice #5, File CA 88324. Part number RoHS Compliant [1] Package Surface Mount ACSL-6210 -00RE SO-8 X -06RE SO-8 X -50RE SO-8 X X -56RE SO-8 X X -00TE SO-16 X -06TE SO-16 X -50TE SO-16 X X -56TE SO-16 X X ACSL-6300 ACSL-6310 ACSL-6400 ACSL-6410 ACSL-6420 Tape & Reel IEC/EN/DIN EN 60747-5-5 Quantity 100 per tube X 100 per tube 1500 per reel X 1500 per reel 50 per tube X 50 per tube 1000 per reel X 1000 per reel Note 1: The ACSL-6xx0 product family is only offered in RoHS compliant option. To order, choose a part number from the part number column and combine with the desired option from the option column to form an order entry. Example 1: ACSL-6210-56RE refers to ordering a Surface Mount SO-8 package in Tape and Reel packaging with IEC/EN/DIN EN 60747-5-5 Safety Approval in RoHS compliant. Example 2: ACSL-6400-00TE refers to ordering a Surface Mount SO-16 package product in tube packaging and in RoHS compliant. Option datasheets are available. Contact your Avago sales representative or authorized distributor for information. Truth Table (Positive Logic) Pin Description Symbol Description Symbol Description LED OUTPUT VDD1 Power Supply 1 GND1 Power Supply Ground 1 ON L VDD2 Power Supply 2 GND2 Power Supply Ground 2 OFF H ANODEx LED Anode NC Not Connected CATHODEx LED Cathode VOX Output Signal 2 Functional Diagrams ACSL-6300 - Triple-Ch, All-in-One ACSL-6210 - Dual-Ch, Bi-Dir GND1 CATHODE2 1 V01 2 7 VDD2 VDD1 3 6 V02 4 5 GND2 CATHODE1 ANODE2 8 ACSL-6210 ANODE1 ANODE1 1 16 GND CATHODE1 VDD ANODE2 V01 CATHODE2 V02 ANODE3 V03 CATHODE3 NC NC NC VDD 8 9 GND 16 GND ACSL-6300 ACSL-6310 - Triple-Ch, Bi-Dir (2/1) GND1 1 ACSL-6400 - Quad-Ch, All-in-One 16 1 NC ANODE1 NC NC CATHODE1 VDD V03 ANODE3 ANODE2 V01 CATHODE2 V02 ANODE3 V03 VDD1 CATHODE3 ANODE1 VDD2 CATHODE1 V01 CATHODE3 V04 ANODE2 V02 ANODE4 VDD CATHODE2 8 9 GND2 CATHODE4 8 ACSL-6310 1 GND 16 ANODE4 ACSL-6400 ACSL-6410 - Quad-Ch, Bi-Dir (3/1) GND1 CATHODE1 9 ACSL-6420 - Quad-Ch, Bi-Dir (2/2) 16 V04 VDD1 CATHODE4 GND1 1 ANODE4 V04 CATHODE4 GND2 V03 ANODE3 CATHODE3 ANODE1 V01 VDD1 CATHODE2 V02 ANODE1 ANODE2 V03 CATHODE1 V01 VDD2 ANODE2 V02 GND2 CATHODE2 CATHODE3 ANODE3 8 9 ACSL-6410 3 VDD2 8 9 ACSL-6420 GND2 Schematic Diagrams The ACSL-6xx0 series optocouplers feature the GaAsP LEDs with proprietary back emission design. They offer the designer a broad range of input drive current, from 7 mA to 15 mA, thus providing greater flexibility in designing the drive circuit. The output detector integrated circuit (IC) in the optocoupler consists of a photodiode at the input of a twostage amplifier that provides both high gain and high bandwidth. The secondary amplifier stage of the detector Vo1 VDD1 The entire output circuit is electrically shielded so that any common-mode transient capacitively coupled from the LED side of the optocoupler is diverted from the photodiode to ground. With this electric shield, the optocoupler can withstand transients that slopes up to 10,000V/µs, and amplitudes up to 1,000V. ACSL-6300 - Triple-Ch, All-in-One ACSL-6210 - Dual-Ch, Bi-Dir GND1 CATHODE2 IC feeds into an open collector Schottky-clamped transistor. Shield 1 16 15 8 ANODE1 ANODE1 2 CATHODE1 3 7 14 VDD Vo1 2 Shield VDD2 6 Vo2 ANODE2 ANODE2 1 GND 3 13 Vo2 4 5 GND2 CATHODE1 Shield CATHODE2 4 Shield ANODE3 CATHODE3 5 12 6 10 9 Shield ACSL-6310 - Triple-Ch, Bi-Dir (2/1) GND1 Shield 1 14 Vo3 VDD1 3 13 4 12 ANODE1 CATHODE1 5 11 ANODE3 CATHODE3 VDD2 Vo1 6 Shield ANODE2 CATHODE2 7 10 8 9 Shield 4 Vo2 GND2 Vo3 VDD GND Schematic Diagrams, continued ACSL-6400 - Quad-Ch, All-in-One ACSL-6410 - Quad-Ch, Bi-Dir (3/1) 16 15 ANODE1 1 14 GND VDD Shield 1 16 Vo1 2 CATHODE1 GND1 CATHODE1 Vo4 VDD1 2 15 3 14 Shield 3 ANODE2 13 13 Vo2 ANODE1 4 CATHODE2 12 CATHODE2 5 ANODE2 7 11 8 10 CATHODE3 Vo4 ANODE3 GND Shield 2 15 ANODE4 CATHODE4 Shield 14 Vo3 VDD1 3 13 4 12 ANODE1 CATHODE1 5 11 ANODE3 CATHODE3 VDD2 Vo1 6 Shield ANODE2 CATHODE2 7 10 9 5 Vo2 8 Shield 11 8 10 VDD ACSL-6420 - Quad-Ch, Bi-Dir (2/2) 16 7 Vo4 Shield 1 Vo2 Shield 9 GND1 Vo1 6 Shield CATHODE4 12 Vo3 6 ANODE4 GND2 Shield 5 CATHODE3 ANODE4 4 Shield ANODE3 CATHODE4 GND2 9 Shield Vo3 VDD2 GND2 Package Outline Drawings ACSL-6210 Small Outline SO-8 Package 0.189 (4.80) 0.197 (5.00) 8 7 6 LAND PATTERN RECOMMENDATION 5 0.228 (5.80) 0.244 (6.20) 0.150 (3.80) 0.157 (4.00) 1 2 3 0.286 (7.27) 0.085 (2.16) 4 0.025 (0.64 ) 0.013 (0.33) 0.020 (0.51) 0.010 (0.25) 0.020 (0.50) x 45° 0.008 (0.19) 0.010 (0.25) 0.004 (0.10) 0.010 (0.25) 0.054 (1.37) 0.069 (1.75) 0° 8° 0.040 (1.016) 0.060 (1.524) 0.016 (0.40) 0.050 (1.27) DIMENSIONS: INCHES (MILLIMETERS) MIN MAX ACSL-6300, ACSL-6310, ACSL-6400, ACSL-6410 and ACSL-6420 Small Outline SO-16 Package 0.386 (9.802) 0.394 (9.999) 8 LAND PATTERN RECOMMENDATION 1 0.228 (5.791) 0.244 (6.197) 0.286 (7.27) 0.152 (3.861) 0.157 (3.988) 0.085 (2.16) 0.013 (0.330) 0.020 (0.508) 0.050 (1.270) 0.060 (1.524) 0.025 (0.64 ) 0.054 (1.372) 0.068 (1.727) 0.010 (0.245) x 45° 0.020 (0.508) 0.008 (0.191) 0.010 (0.249) 0 - 8° TYP. 0.040 (1.016) 0.060 (1.524) DIMENSIONS: INCHES (MILLIMETERS) MIN MAX 6 0.004 (0.102) 0.010 (0.249) 0.016 (0.406) 0.050 (1.270) Reflow Soldering Profile The recommended reflow soldering conditions are per JEDEC Standard J-STD-020 (latest revision). Non-halide flux should be used. Regulatory Information Insulation and Safety Related Specifications Parameter Symbol Value Units Conditions Minimum External Air Gap L(I01) 4.9 mm (Clearance) Measured from input terminals to output terminals, shortest distance through air Minimum Externa l Tracking L(I02) 4.5 mm (Creepage) Measured from input terminals to output terminals, shortest distance path through body Minimum Internal Plastic Gap 0.08 mm Insulation thickness between emitter and (Internal Clearance) detector; also known as distance through insulation Tracking Resistance (Comparative Tracking Index) CTI Isolation Group 175 Volts IIIa DIN IEC 112/VDE0303 Part 1 Material Group (DIN VDE 0110, 1/89, Table 1) IEC/EN/DIN EN 60747-5-5 Insulation Characteristics* (Option x6xx) Description Symbol Characteristic Installation classification per DIN VDE 0110, Table 1 for rated mains voltage ≤ 150 Vrms for rated mains voltage ≤ 300 Vrms I – IV I – III Climatic Classification 40/100/21 Pollution Degree (DIN VDE 0110/39) Unit 2 Maximum Working Insulation Voltage VIORM 567 Vpeak Input to Output Test Voltage, Method b* VIORM x 1.875 = VPR, 100% Production Test with tm=1 sec, Partial discharge < 5 pC VPR 1063 Vpeak Input to Output Test Voltage, Method a* VIORM x 1.6 = VPR, Type and Sample Test, tm=10 sec, Partial discharge < 5 pC VPR 907 Vpeak Highest Allowable Overvoltage (Transient Overvoltage tini = 60 sec) VIOTM 4000 Vpeak Safety-limiting values – maximum values allowed in the event of a failure. Case Temperature Input Current** Output Power** TS IS, INPUT PS, OUTPUT 175 150 600 °C mA mW Insulation Resistance at TS, VIO = 500 V RS >109 W * 700 Is (mA) Ps (mW) 600 Output Power-Ps Input Power-lp Refer to the optocoupler section of the Isolation and Control Components Designer’s Catalog, under Product Safety Regulations section, (IEC/EN/DIN EN 60747-5-5) for a detailed description of Method a and Method b partial discharge test profiles. ** Refer to following figure for dependence of PS and IS on ambient temperature. 500 400 300 200 100 0 7 0 25 50 75 100 125 150 175 200 Ts-Case Temperature,°C Absolute Maximum Ratings Parameter Symbol Min. Max. Units Storage Temperature Ts -55 125 °C Operating Temperature TA -40 100 °C Supply Voltage (1 Minute Maximum) VDD1 , VDD2 7 V Reverse Input Voltage (Per Channel) VR 5 V Output Voltage (Per Channel) VO 7 V Average Forward Input Current (Per Channel) IF mA Output Current (Per Channel) IO 50 mA Input Power Dissipation[2] (Per Channel) PI 27 mW Output Power Dissipation[2] (Per Channel) PO 65 mW Symbol Min. Max. Units TA -40 100 °C [1] 15 Recommended Operating Conditions Parameter Operating Temperature Input Current, Low Level IFL 0 250 µA Input Current, High Level[4] IFH 7 15 mA Supply Voltage VDD1, VDD2 3.0 5.5 V [3] Fan Out (at RL = 1kΩ) N 5 TTL Loads Output Pull-up Resistor RL 4k Ω 330 Notes: 1. Peaking circuits may produce transient input currents up to 50 mA, 50 ns max. pulse width, provided average current does not exceed its max. values. 2. Derate total package power dissipation, PT linearly above +95°C free-air temperature at a rate of 1.57mW/°C for the SO8 package mounted on low conductivity board per JESD 51-3. Derate total package power dissipation, PT linearly above +80°C free-air temperature at a rate of 1.59 mW/°C for the SO16 package mounted on low conductivity board per JESD 51-3. PT= number of channels multiplied by (PI+PO). 3. The off condition can be guaranteed by ensuring that VFL ≤ 0.8V. 4. The initial switching threshold is 7 mA or less. It is recommended that minimum 8 mA be used for best performance and to permit guardband for LED degradation. PT - Total Power Dissipation per channel - mW 100 90 80 70 60 50 40 30 20 10 0 8 so-16 package so-8 package 0 20 40 60 80 100 TA - Ambient Temperature - °C 120 Electrical Specifications Over recommended operating range (3.0V ≤ VDD1 ≤ 3.6V, 3.0V ≤ VDD2 ≤ 3.6V, TA = -40°C to +100°C) unless otherwise specified. All typical specifications are at TA = +25°C , VDD1 = VDD2 = +3.3V. Parameter Symbol Min. Input Threshold Current ITH High Level Output Current IOH Low Level Output Voltage VOL High Level Supply Current (per channel) Typ. Max. Units Test Conditions 2.7 7.0 mA IOL(Sinking)=13 mA, VO = 0.6V 4.7 100.0 µA IF = 250 µA, VO = 3.3V 0.36 0.68 V IOL(Sinking) = 13 mA, IF = 7mA IDDH 3.2 5.0 mA IF = 0 mA Low Level Supply Current (per channel) IDDL 4.6 7.5 mA IF = 10 mA Input Forward Voltage VF 1.25 1.52 1.80 Input Reverse Breakdown Voltage BVR 5.0 Input Diode Temperature Coefficient ∆VF / ∆TA Input Capacitance CIN V IF = 10 mA, TA = 25°C V IR = 10 µA -1.8 mV/°C IF = 10 mA 80 pF f = 1 MHz, VF = 0V Switching Specifications Over recommended operating range (3.0V ≤ VDD1 ≤ 3.6V, 3.0V ≤ VDD2 ≤ 3.6V, IF = 8.0 mA, TA = -40°C to +100°C) unless otherwise specified. All typical specifications are at TA = +25°C , VDD1 = VDD2 = +3.3V. Parameter Symbol Min. Typ. Max. Units Maximum Data Rate 10 15 Pulse Width tPW 100ns Propagation Delay Time to Logic High Output Level [5] tPLH 52 100 ns RL = 350Ω, CL = 15 pF Propagation Delay Time to Logic Low Output Level [6] tPHL 44 100 ns RL = 350Ω, CL = 15 pF Pulse Width Distortion |tPHL – tPLH| |PWD| 8 35 ns RL = 350Ω, CL = 15 pF Propagation Delay Skew[7] tPSK40 ns RL = 350Ω, CL = 15 pF Output Rise Time (10 – 90%) tR35ns RL = 350Ω, CL = 15 pF Output Fall Time (10 – 90%) tF12ns RL = 350Ω, CL = 15 pF MBd Test Conditions RL = 350Ω, CL = 15 pF RL = 350Ω, CL = 15 pF Logic High Common Mode |CMH| 10kV/µs Vcm = 1000V, IF = 0 mA, Transient Immunity [8]VO = 2.0V, RL = 350Ω, TA = 25°C Logic Low Common Mode |CML| 10kV/µs Vcm = 1000V, IF = 8 mA, Transient Immunity [8]VO = 0.8V, RL = 350Ω, TA = 25°C Notes: 5. tPLH is measured from the 4.0 mA level on the falling edge of the input pulse to the 1.5V level on the rising edge of the output pulse. 6. tPHL is measured from the 4.0 mA level on the rising edge of the input pulse to the 1.5V level on the falling edge of the output pulse. 7. tPSK is equal to the worst case difference in tPHL and/or tPLH that will be seen between units at any given temperature and specified test conditions. 8. CMH is the maximum common mode voltage slew rate that can be sustained while maintaining VO > 2.0V. CML is the maximum common mode voltage slew rate that can be sustained while maintaining VO < 0.8V. The common mode voltage slew rates apply to both rising and falling common mode voltage edges. 9 Electrical Specifications Over recommended operating range (4.5V ≤ VDD1 ≤ 5.5V, 4.5V ≤ VDD2 ≤ 5.5V, TA = -40°C to +100°C) unless otherwise specified. All typical specifications are at TA = +25°C, VDD1 = VDD2 = +5.0V. Parameter Symbol Min. Typ. Max. Units Test Conditions Input Threshold Current ITH 2.7 7.0 mA IOL(Sinking)=13 mA, VO= 0.6V High Level Output Current IOH 3.8 100.0 µA IF = 250 µA, VO= 5.5V Low Level Output Voltage VOL 0.36 0.6 V IOL(Sinking)=13 mA, IF=7 mA High Level Supply Current (per channel) IDDH 4.3 7.5 mA IF = 0 mA Low Level Supply Current (per channel) IDDL 5.8 10.5 mA IF = 10 mA Input Forward Voltage VF 1.25 1.52 1.8 V IF = 10 mA, TA = 25°C Input Reverse Breakdown Voltage BVR 5.0 V IR = 10 µA Input Diode Temperature Coefficient ∆VF / ∆TA -1.8 mV/°C IF = 10 mA Input Capacitance CIN 80 pF f = 1 MHz, VF = 0V Switching Specifications Over recommended operating range (4.5V ≤ VDD1 ≤ 5.5V, 4.5V ≤ VDD2 ≤ 5.5V, IF = 8.0 mA, TA = -40°C to +100°C) unless otherwise specified. All typical specifications are at TA=+25°C, VDD1 = VDD2 = +5.0V. Parameter Symbol Min. Typ. Max. Units Maximum Data Rate 10 15 Pulse Width tPW 100ns Propagation Delay Time to Logic High Output Level[5] tPLH 46 100 ns RL = 350Ω, CL =15 pF Propagation Delay Time to Logic Low Output Level[6] tPHL 43 100 ns RL = 350Ω, CL =15 pF Pulse Width Distortion |tPHL – tPLH| |PWD| 5 35 ns RL = 350Ω, CL =15 pF Propagation Delay Skew[7] tPSK40 ns RL = 350Ω, CL =15 pF Output Rise Time (10 – 90%) tR30ns RL = 350Ω, CL =15 pF Output Fall Time (10 – 90%) tF12ns RL = 350Ω, CL =15 pF MBd Test Conditions RL = 350Ω, CL =15 pF RL = 350Ω, CL =15 pF Logic High Common Mode |CMH| 10kV/µs Vcm= 1000V, IF=0 mA, Transient Immunity [8]VO = 2.0V, RL=350Ω, TA = 25°C Logic Low Common Mode |CML| 10kV/µs Vcm= 1000V, IF= 8 mA, Transient Immunity [8]VO = 0.8V, RL= 350Ω, TA = 25°C Notes: 5. tPLH is measured from the 4.0 mA level on the falling edge of the input pulse to the 1.5V level on the rising edge of the output pulse. 6. tPHL is measured from the 4.0 mA level on the rising edge of the input pulse to the 1.5V level on the falling edge of the output pulse. 7. tPSK is equal to the worst case difference in tPHL and/or tPLH that will be seen between units at any given temperature and specified test conditions. 8. CMH is the maximum common mode voltage slew rate that can be sustained while maintaining VO > 2.0V. CML is the maximum common mode voltage slew rate that can be sustained while maintaining VO < 0.8V. The common mode voltage slew rates apply to both rising and falling common mode voltage edges. 10 Package Characteristics All specifications are at TA=+25°C. Parameter Symbol Min. Input-Output Momentary Withstand Voltage[9] SO8 SO16 VISO VISO 2500 VRMS 2500 Input-Output Insulation [10] [11] SO8 SO16 II-O II-O Input-Output Resistance[10] SO8 SO16 RI-O RI-O Input-Output Capacitance[10] SO8 SO16 CI-O CI-O 0.7 pF 0.7 f = 1 MHz f = 1 MHz Input-Input Insulation Leakage Current[12] SO8 SO16 II-I II-I 0.005 µA 0.005 RH ≤ 45%, t=5 sec, VI-I=500V RH≤45%, t=5 sec, VI-I=500V Input-Input Resistance[12] SO8 SO16 RI-I1011 Ω RI-I1011 RH≤45%, t= 5 sec, VI-I=500V RH≤45%, t=5 sec, VI-I =500V Input-Input Capacitance[12] SO8 SO16 CI-I CI-I f = 1 MHz f = 1 MHz 109 109 Typ. Max. Units 5 µA 5 Test Conditions RH ≤ 50%, t = 1 min RH≤50%, t = 1 min 45% RH, t=5 sec, VI-O= 3kV DC 45% RH, t=5 sec, VI-O=3kV DC 1011 Ω VI-O = 500V DC 1011 VI-O = 500V DC 0.1 pF 0.12 Notes: 9. VISO is a dielectric voltage rating that should not be interpreted as an input-output continuous voltage rating. For continuous voltage rating, refer to the IEC/EN/DIN EN 60747-5-5 Insulation Characteristics Table (if applicable), the equipment level safety specification or Avago Application Note 1074 entitled “Optocoupler Input-Output Endurance Voltage.” 10. Measured between each input pair shorted together and all output connections for that channel shorted together. 11. In accordance to UL1577, each optocoupler is proof tested by applying an insulation test voltage ≥ 3000 Vrms for 1 sec (leakage detection current limit, II-O ≤ 5 µA). This test is performed before the 100% production test for partial discharge (Method b) shown in the IEC/EN/DIN EN 60747-5-5 Insulation Characteristics Table, if applicable. 12. Measured between inputs with the LED anode and cathode shorted together. Electrostatic Discharge Sensitivity This product has been tested for electrostatic sensitivity to the limits stated in the specifications. However, Avago recommends that all integrated circuits be handled with appropriate care to avoid damage. Damage caused by inappropriate handling or storage could range from performance degradation to complete failure. 11 Typical Performance 70 5 4 R L = 350 Ω 3 R L = 1 KΩ 2 R L = 4 KΩ 1 0 VDD = 5.0V VO = 0.6V 5 4 RL = 350 Ω 3 RL = 1 KΩ 2 RL = 4 KΩ 1 -40 -20 0 20 40 60 80 100 120 -60 -40 -20 Figure 1. Typical input threshold current vs. temperature for 3.3V operation. 0 20 40 60 80 100 IF = 10 mA 50 IF = 7.0 mA 40 30 20 20 40 -40 -20 60 80 100 VDD = 3.3V VO = 3.3V IF = 250 A 10 5 T A - TEMPERATURE - C 40 60 80 100 120 Figure 3. Typical low level output current vs. temperature for 3.3V operation. VDD = 5.0V VO = 5.0V IF = 250 A 10 5 0 0 20 40 60 80 -60 100 120 -40 -20 TA - TEMPERATURE - C Figure 4. Typical low level output current vs. temperature for 5V operation. 20 15 0 -60 -40 -20 120 0 TA - TEMPERATURE - C IOH- HIGH LEVEL OUTPUT CURRENT -A IOH- HIGH LEVEL OUTPUT CURRENT -A 60 0 30 -60 15 VDD = 5.0V VOL = 0.6V -20 IF = 7.0 mA 40 120 Figure 2. Typical input threshold current vs. temperature for 5V operation. 70 -40 50 TA - TEMPERATURE - C T A - TEMPERATURE - C -60 V DD = 3.3V V OL = 0.6V 60 20 0 -60 IOL- LOW LEVEL OUTPUT CURRENT - mA IOL - LOW LEVEL OUTPUT CURRENT - mA 6 VDD = 3.3V VO = 0.6V ITH - INPUT THRESHOLD CURRENT - mA ITH - INPUT THRESHOLD CURRENT - mA 6 0 20 40 60 80 100 120 T A - TEMPERATURE - C Figure 5. Typical high level output current vs. temperature for 3.3V operation. Figure 6. Typical high level output current vs. temperature for 5V operation. VDD = 3.3V IF = 7 mA 0.7 0.6 0.5 0.4 0.3 IO = 13 mA 0.2 0.1 0.0 -60 -40 -20 0 20 40 60 80 100 120 TA - TEMPERATURE -C Figure 7. Typical low level output voltage vs. temperature for 3.3V operation. 12 VOL - LOW LEVEL OUTPUT VOLTAGE - V VOL- LOW LEVEL OUTPUT VOLTAGE - V 0.8 VDD = 5.0V IF = 7 mA 0.7 0.6 0.5 0.4 0.3 IO = 13 mA 0.2 0.1 0.0 -60 -40 -20 0 20 40 60 80 TA - TEMPERATURE -C 100 120 Figure 8. Typical low level output voltage vs. temperature for 5V operation. IDD- SUPPLY CURRENT PER CHANNEL - mA 10 0.8 VDD = 3.3V 9 8 7 6 IDDL IF = 10 mA 5 4 3 2 IDDH IF = 0 mA 1 0 -60 -40 -20 0 20 40 60 80 TA - TEMPERATURE -C 100 120 Figure 9. Typical supply current per channel vs. temperature for 3.3V operation. Typical Performance, continued 10 VDD = 5.0V 1000 8 IDDL IF = 10 mA 5 4 IDDH IF = 0 mA 3 2 10 -60 -40 -20 F + F – 0.1 0 20 40 60 TA - TEMPERATURE - C 80 100 120 0.001 1.1 90 tPLH, RL = 350Ω 30 tPHL, RL = 350Ω 0 -60 -40 -20 0 20 40 60 1.4 1.5 tPLH, RL = 350Ω 60 30 tPHL, RL = 350Ω 0 -60 -40 -20 1.6 80 100 120 TA - TEMPERATURE - C Figure 13. Typical propagation delay vs. temperature for 5V operation. 0 20 40 60 TA - TEMPERATURE - C 80 100 120 Figure 12. Typical propagation delay vs. temperature for 3.3V operation. 40 PWD - PULSE WIDTH DISTORTION - ns VDD = 5.0V IF = 8.0 mA 60 1.3 90 Figure 11. Typical input diode forward characteristics. 150 120 1.2 VDD = 3.3V IF = 8.0 mA 120 VF - FORWARD VOLTAGE - V Figure 10. Typical supply current per channel vs. temperature for 5V operation. tP - PROPAGATION DELAY - ns V 0.01 1 0 13 I 1 40 VDD = 3.3V IF = 8.0 mA 30 20 10 RL = 350Ω 0 -60 -40 -20 0 20 40 60 80 100 120 TA - TEMPERATURE - C Figure 14. Typical pulse width distortion vs. temperature for 3.3V operation. PWD - PULSE WIDTH DISTORTION - ns 6 tP - PROPAGATION DELAY - ns 7 150 TA = 25C 100 IF - FORWARD CURRENT - mA IDD - SUPPLY CURRENT PER CHANNEL - mA 9 VDD = 5.0V IF = 8.0 mA 30 20 10 0 RL = 350Ω -60 -40 -20 0 20 40 60 TA - TEMPERATURE - C 80 100 120 Figure 15. Typical pulse width distortion vs. temperature for 5V operation. Test Circuits ACSL-6210 INPUT MONITORING NODE 3.3V or 5V 1 8 2 7 3 6 4 5 0.1µF BYPASS RL C L* PULSE GEN. Zo = 50Ω tf = tr = 5ns OUTPUT Vo MONITORING NODE IF *C L IS APPROXIMATELY 15 pF WHICH INCLUDES PROBE AND STRAY WIRING CAPACITANCE IF = 8.0 mA INPUT IF IF = 4.0 mA tPLH tPHL 90% 90% OUTPUT Vo 1.5V 10% 10% tF tR Figure 16. Test circuit for tPHL. tPLH, tF, and tR. ACSL-6400 IF 3.3V or 5V B 1 16 A RL OUTPUT Vo MONITORING NODE 0.1µF BYPASS V FF 8 9 _ + PULSE GEN. Zo = 50 Vcm (peak) Vcm 0V 5V SWITCH AT POSITION "A": IF = 0 mA CM H Vo Vo (min.) SWITCH AT POSITION "B": IF = 8 mA Vo (max.) Vo 0.5 V CM L Figure 17. Test circuit for common mode transient immunity and typical waveforms Figure 17. Test circuit for common mode transient immunity and typical waveforms. 14 Application Information ON and OFF Conditions The ACSL-6xx0 series has the ON condition defined by current, and the OFF condition defined by voltage. In order to guarantee that the optocoupler is OFF, the forward voltage across the LED must be less than or equal to 0.8 volt for the entire operating temperature range. This has direct implications for the input drive circuit. If the design uses a TTL gate to drive the input LED, then one has to ensure that the gate output voltage is sufficient to cause the forward voltage to be less than 0.8 volt. The typical threshold current for the ACSL‑6xx0 series optocouplers is 2.7 mA; however, this threshold could increase over time due to the aging effects of the LED. Drive circuit arrangements must provide for the ON state LED forward current of at least 7 mA, or more if faster operation is desired. Maximum Input Current and Reverse Voltage The average forward input current should not exceed the 15 mA Absolute Maximum Rating as stated; however, peaking circuits with transient input currents up to 50 mA are allowed provided the average current does not exceed 15 mA. If the input current maximum rating is exceeded, Figure 18. TTL interface circuit for the ACSL-6xx0. 15 the local temperature of the LED can rise, which in turn may affect the long-term reliability of the device. When designing the input circuit, one must also ensure that the input reverse voltage does not exceed 5 V. If the optocoupler is subjected to reverse voltage transients or accidental situations that may cause a reverse voltage to be applied, thus an antiparallel diode across the LED is recommended. Suggested Input Circuits for Driving the LED Figures 18, 19, and 20 show some of the several techniques for driving the ACSL-6xx0 LED. Figure 18 shows the recommended circuit when using any type of TTL gate. The buffer PNP transistor allows the circuit to be used with TTL or CMOS gates that have low sinking current capability. One advantage of this circuit is that there is very little variation in power supply current due to the switching of the optocoupler LED. This can be important in highresolution analog-to-digital (A/D) systems where ground loop currents due to the switching of the LEDs can cause distortion in the A/D output. With a CMOS gate to drive the optocoupler, the circuit shown in Figure 19 can be used. The diode in parallel to the current limiting resistor speeds the turn-off of the optocoupler LED. Any HC or HCT series CMOS gate can be used in this circuit. For high common-mode rejection applications, the drive circuit shown in Figure 20 is recommended. In this circuit, only an open-collector TTL, or an open drain CMOS gate can be used. This circuit drives the optocoupler LED with a 220 ohm current-limiting resistor to ensure that an IF of 7 mA is applied under worst case conditions and thus guarantee the 10,000 V/µs optocoupler common mode rejection rating. The designer can obtain even higher common-mode rejection performance than 10,000 V/µs by driving the LED harder than 7 mA. Phase Relationship to Input The output of the optocoupler is inverted when compared to the input. The input is defined to be logic HIGH when the LED is ON. If there is a design that requires the optocoupler to behave as a non-inverting gate, then the series input drive circuit shown in Figure 19 can be used. This input drive circuit has an inverting function, and since the optocoupler also behaves as an inverter, the total circuit is non-inverting. The shunt drive circuits shown in Figures 18 and 20 will cause the optocoupler to function as an inverter. Current and Voltage Limitations The absolute maximum voltage allowable at the output supply voltage pin and the output voltage pin of the optocoupler is 7 volts. However, the recommended maximum voltage at these two pins is 5.5 volts. The output sinking current should not exceed 13 mA in order to make the Low Level Output Voltage be less than 0.6 volt. If the output voltage is not a consideration, then the absolute maximum current allowed through the ACSL-6xx0 is 50 mA. If the output requires switching either higher currents or voltages, output buffer stages as shown in Figures 21 and 22 are suggested. Figure 19. CMOS drive circuit for the ACSL‑6xx0. Figure 21. High voltage switching with ACSL‑6xx0. Figure 20. High CMR drive circuit for the ACSL‑6xx0. 16 Figure 22. High voltage and high current switching with ACSL‑6xx0. Propagation Delay, Pulse-Width Distortion and Propagation Delay Skew Propagation delay is a figure of merit which describes how quickly a logic signal propagates through a system. The propagation delay from low to high (tPLH) is the amount of time required for an input signal to propagate to the output, causing the output to change from low to high. Similarly, the propagation delay from high to low (tPHL) is the amount of time required for the input signal to propagate to the output causing the output to change from high to low (see Figure 16). Pulse-width distortion (PWD) results when tPLH and tPHL differ in value. PWD is defined as the difference between tPLH and tPHL and often determines the maximum data rate capability of a transmission system. PWD can be expressed in percent by dividing the PWD (in ns) by the minimum pulse width (in ns) being transmitted. Typically, PWD on the order of 20-30% of the minimum pulse width is tolerable; the exact figure depends on the particular application (RS232, RS422, T-l, etc.). operating temperature). As illustrated in Figure 23, if the inputs of a group of optocouplers are switched either ON or OFF at the same time, tPSK is the difference between the shortest propagation delay,either tPLH or tPHL, and the longest propagation delay,either tPLH or tPHL. As mentioned earlier,tPSK can determine the maximum parallel data transmission rate. Figure 24 is the timing diagram of a typical parallel data application with both the clock and the data lines being sent through optocouplers. The figure shows data and clock signals at the inputs and outputs of the optocouplers. To obtain the maximum data transmission rate, both edges of the clock signal are being used to clock the data;if only one edge were used, the clock signal would need to be twice as fast. Propagation delay skew,tPSK, is an important parameter to consider in parallel data applica- tions where synchronization of signals on parallel data lines is a concern. If the parallel data is being sent through a group of optocouplers, differences in propagation delays will cause the data to arrive at the outputs of the optocouplers at different times. If this difference in propagation delays is large enough, it will determine the maximum rate at which parallel data can be sent through the optocouplers. Propagation delay skew repre- sents the uncertainty of where an edge might be after being sent through an optocoupler. Figure 24 shows that there will be uncertainty in both the data and the clock lines. It is important that these two areas of uncertainty not overlap, otherwise the clock signal might arrive before all of the data outputs have settled,or some of the data outputs may start to change before the clock signal has arrived. From these considerations, the absolute minimum pulse width that can be sent through optocouplers in a parallel application is twice tPSK. A cautious design should use a slightly longer pulse width to ensure that any additional uncertainty in the rest of the circuit does not cause a problem. Propagation delay skew is defined as the difference between the minimum and maximum propagation delays,either tPLH or tPHL, for any given group of optocouplers which are operating under the same conditions (i.e., the same drive current, supply voltage, output load, and The tPSK specified optocouplers offer the advantages of guaranteed specifications for propagation delays, pulsewidth distortion and propagation delay skew over the recommended temperature, input current, and power supply ranges. IF DATA 50% INPUTS VO CLOCK 1.5 V IF 50% DATA OUTPUTS VO 1.5 V t PSK CLOCK t PSK Figure 23. Propagation delay skew – tPSK. t PSK Figure 24. Parallel data transmission example. For product information and a complete list of distributors, please go to our web site: www.avagotech.com Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies in the United States and other countries. Data subject to change. Copyright © 2005-2014 Avago Technologies. All rights reserved. Obsoletes 5989-2159EN AV02-0235EN - March 25, 2014