7 8 THIS DRAWING IS UNPUBLISHED. C 5 4 3 2 RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. COPYRIGHT 6 ATLANTIC VERSION TERMINATOR INTERFACE ADAPTER PART NUMBER REVISION 2151842 -1 A 2151842 -2 FEED TYPE FINE CRIMP HEIGHT ADJUST A 2151842 -5 D DESCRIPTION FINE CRIMP HEIGHT ADJUST A MECHANICAL PNEUMATIC SERVO LATCH PLATE SMART APPLICATOR MECHANICAL FEED SERVO LATCH PLATE SMART APPLICATOR FINE CRIMP HEIGHT ADJUST MECHANICAL FEED - 2151842 -6 A NON-CRIMP HEIGHT ADJUST 2151842 -7 A FINE CRIMP HEIGHT ADJUST NONE A PNEUMATIC FEED SERVO LATCH PLATE SERVO LATCH PLATE 7- 2151842 -7 APPLICATOR STYLE CONVERSION CHART CONVERT TO CRIMP TOOLING KIT - PNEUMATIC FEED 2119950-1 1338683-1 2161326-1 - 2119951-1 - 2119949-1 1338683-1 - 2119951-1 2161326-1 - 2119949-1 1338683-1 2119950-1 5-18022-5 8- 2151842 -5 8- 2151842 -4 5-18022-5 8- 2151842 -5 8- 2151842 -4 5-18022-5 1338683-1 - 5-18022-5 - - 2119641-1 2119799-1 CRIMP WIRE INSUL SIZE - - 1901094-3 2119653-1 1901094-3 - 2119653-1 2119641-1 - - - - 2168400-6 2168400-6 - (QUANTITY 2) - - 2119799-1 - 2063440-1 - - - - - - - - - - - - - - - - - - (QUANTITY 2) - - - - - - - - - - - TYPE - O - 2.79 mm [.110] - APPLICATOR INSTRUCTIONS 408-10389 - INDAK TERMINAL TERMINAL DATA: WIRE STRIP LENGTH 3.54-3.84 mm [.139-.151 IN] C TERMINAL APPLICATION SPECIFICATION - TE CRIMP SPECIFICATION TERMINAL TERMINAL NAME: - INSULATION DIAMETER RANGE TE SPEC - - - - - - - - - - TERMINALS APPLIED TE TERMINAL 2113311-1 INDAK TERMINAL C81015 C1__DWG_PN_1_0 C1__DWG_PN_1_1 C1__DWG_PN_2_0 TE TERMINAL C1__DWG_PN_3_0 - INDAK TERMINAL - C1__DWG_PN_4_0 - C1__DWG_PN_2_1 - WIRE SIZE 16 AWG 18 AWG 20 AWG CRIMP HEIGHT mm [INCH] W1__DWG_WGAUGE_1 W1__DWG_WGAUGE_2 W1__DWG_WGAUGE_3 1.88+/-0.05 [.074+/-.002] 1.80+/-0.05 [.071+/-.002] 1.73+/-0.05 [.068+/-.002] - CRIMP HEIGHT REFERENCE SETTING W1__DWG_CRIMP_HT_1 W1__DWG_CRIMP_HT_2 W1__DWG_CRIMP_HT_3 7.5 7.5 7.9 - W1__FA_SETTING_1 - W1__FA_SETTING_2 - W1__FA_SETTING_3 - *WARNING ON INSTALLATION, SET WIRE DISC, ITEM 40 TO LARGEST WIRE SIZE SETTING. USE OF SETTINGS BELOW MINIMUM REQUIRED CRIMP HEIGHT SETTING WILL CAUSE DAMAGE TO CRIMP TOOLING. - B - 1 1 1 1 - -77 -7 A P LTR DESCRIPTION DATE DWN APVD 2063440-1 - APPLICATOR DATA REVISIONS DIST PART NUMBERS REQUIRED - LOC SET UP GAUGE 2119599-1 ALL RIGHTS RESERVED. 1 1 1 1 2 -6 1 1 1 1 2 -5 1 1 1 1 1 1 1 - -2 - 2119957-2 8-21084-0 2119640-1 2079988-1 2119641-1 2119798-1 1-22279-3 2119758-1 7-18023-7 2168400-6 -1 PART NO 1 1 1 1 APPLICATOR SHIM PACK O-RING, .676 ID, .070 DIA. MAT. PUSH ROD, AIR FEED BUSHING, LCH5-12, MISUMI FEED CAM, AIR FEED DETENT PIN SPRING, COMPRESSION RAM, AMP STYLE, SIDE FEED, NON-ADJ. SCR, SKT HD CAP M3 X 4.0 SHCS, LOW HEAD, RoHS, M5 X 16 DESCRIPTION 1 2119957-2 1 8-21084-0_GATD 1 2119640-1 1 2079988_GATD 1 2119641-1 1 2119798-1 1 1-22279-3_SIMP 1 2119758 1 7-18023-7 2 2168400-6 - 260 252 250 249 248 247 246 245 241 240 1 1 ITEM NO 1 1 REF 1 1 1 2 1 1 1 1 1 1 1 2 1 3 2 1 2 2 1 1 1 1 1 1 1 1 2 1 1 1 2 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 -77 -7 - - - - 1 1 1 1 1 1 - - 1 1 1 1 2 1 1 2119580-1 2063440-1 1-356885-4 2119740-2 1901094-3 21045-3 994969-1 994970-2 240638-1 3-23627-7 2119799-1 SEE NOTE 4 1633743-1 1-22281-8 1-18028-2 2119944-1 1-690438-0 2168083-1 2168083-6 455888-5 1-240641-8 2119956-1 2119791-5 2119943-1 2119740-1 2168078-1 2119793-1 992763-5 2-18032-5 2079383-4 5-18022-5 1338683-1 2168400-1 2168083-8 18023-9 2119652-1 2119653-1 2119656-9 2119370-1 2079383-7 2119645-1 2119957-1 2119644-2 2119085-1 2119092-1 2168083-1 2161328-1 1901091-1 1-455888-0 22283-1 356835-1 240792-1 3-189124-3 980371-4 2168083-2 1-18028-2 2119533-1 690463-1 1-2168083-1 1-690464-5 2119862-1 2119806-1 3-22280-3 1-1633933-6 690468-1 2-459492-9 -1 PART NO 1 1 1 REF REF REF REF - - - - - - REF REF 1 1 1 1 1 1 REF REF 1 1 2 2 1 1 1 1 1 1 1 1 1 1 1 1 - - 2 2 - 1 - 3 2 2 1 1 - - - - 2 2 2 2 - - - - - - 1 1 - 1 1 1 - 1 - 1 1 1 1 1 - 1 2 2 1 1 1 1 1 1 2 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 2 1 1 1 1 1 1 1 1 - - - - 1 1 - - 1 1 - - - - - - - - 1 1 -6 -5 1 1 1 1 1 1 2 1 1 1 1 1 1 1 2 1 3 2 1 1 1 2 2 1 1 1 1 1 1 1 1 1 2 1 1 1 2 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 -2 THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. 1 1 1 2 1 1 1 1 1 1 1 2 1 3 2 1 1 1 2 2 2 1 1 1 1 1 1 1 1 1 1 2 1 1 1 2 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 - MECHANICAL FEED ASSEMBLY AIR FEED MODULE STOP, SHEAR TAG,IDENTIFICATION SPACER, FEEDER RING, RETAIN, EXTERN, 3/16 CRESCENT MAGNET, RARE EARTH HIGH ENERGY COUNTER, MAGNETIC SPRING, FEED FINGER PIN, RETAIN, GRVD, 3/16 X .854 HOLDER,FEED FINGER, AF MEMORY CHIP, PROGRAMMED SERVO FEED LATCH ASM SPRING, COMPRESSION WASHER, FLAT, REG M4 FEED FINGER ASSEMBLY,SF FRONT STRIP GUIDE SCR, SKT HD CAP, RoHS, M3 X 8.0 SCR, SKT HD CAP, RoHS, M5 X 65 SPACER, CRIMPER SPACER DOCUMENTATION PACKAGE DEPRESSOR, WIRE WASHER, SPACER TAG,IDENTIFICATION SCREW, DRIVE, RH, RoHS LIMITER, ADJUSTMENT BOLT SCR, SET, SOC, CONE POINT, M3 x 4.0 SCR, SET, FLT POINT M5 X 20.0 SCR, BHSC, RoHS (M4 X 8) SCR, HEX HD CAP, M4 X 6.0 FEED PAWL SHCS, LOW HEAD, RoHS, M4 X 12 SCR, SKT HD CAP, RoHS, M4 X 16 SCR, SKT HD CAP M4 X 6.0 FEED CAM, PRE FEED FEED CAM, POST FEED APPLICATOR BASIC ASSEMBLY, SF RAM, AMP STYLE, SIDE FEED SCR, BHSC, RoHS (M8 X 25) DISC, NUMBERED FA WIRE ADJUSTMENT APPLICATOR SHIM PACK RAM WASHER, PRECISION FA HEAD, ATLANTIC STYLE BOLT, ADJUSTMENT SCR, SKT HD CAP, RoHS, M3 X 8.0 HEX HEAD, FLANGED, M5 x 8mm LONG PLATE, REAR STRIP GUIDE SPACER, CRIMPER SPRING, COMPRESSION LEVER, DRAG RELEASE DRAG, TERMINAL GUIDE, FRONT STRIP SCR, SKT HD SHLDR 5.0 DIA X 6.0 SCR, SKT HD CAP, RoHS, M4 X 8.0 WASHER, FLAT, REG M4 STRIPPER, SIDE FEED FLOATING SHEAR, REAR SCR, SKT HD CAP, RoHS, M3 X 6 SHEAR PLATE, REAR SHEAR HOLDER, REAR INSERT, SHEAR SPRING, COMPRESSION ANVIL, COMBINATION DEPRESSOR SHEAR, REAR CRIMPER, WIRE O 1 2119580-1 1 2063440-1 1 1-356885-4 1 2119740-2 .. 1 1901094-3 2 21045-3 1 994969-1_GATD 1 COUNTER_994970 1 240638 1 3-23627-7 1 2119799 1 1901689_EMPTY_OCEAN_SF .. 1 1633743-1 1 1-22281-8 1 1-18028-2 1 2119944-1 1 1-690438-0 2 2168083-1 1 2168083-6 1 455888-5 1 1-240641-8 1 2119956-1 1 2119791-5 1 2119943-1 1 2119740-1 2 2168078-1 1 2119793 3 992763-5 2 2-18032-5 1 2079383-4 1 5-18022-5 1 1338683-1 2 2168400-1 2 2168083-8 3 18023-9 1 2119652 1 2119653 1 2119656-9 1 2119370 1 2079383-7 1 2119645 1 2119957-1 1 2119644-2 1 2119085 1 2119092-1 2 2168083-1 1 2161328 1 1901091-1 1 1-455888-0 2 22283-1 1 356835-1 1 240792-1 1 3-189124-3 1 980371-4 1 2168083-2 1 1-18028-2 1 2119533 1 690463-1 2 1-2168083-1 1 1-690464-5 1 2119862 1 2119806 1 SIMP_3-22280-3 .. 1 ITEM_10 .. 1 ITEM_9 1 1-1633933-6 .. 1 ITEM_7 1 690468-1 .. 1 ITEM_5 .. 1 ITEM_4 .. 1 ITEM_3 .. 1 ITEM_2 1 2-459492-9 239 238 237 213 198 172 166 164 163 137 136 135 133 121 119 117 96 95 93 82 81 71 70 69 67 66 63 62 61 60 59 56 54 53 49 48 47 46 44 41 40 39 38 37 35 33 32 29 28 27 26 25 24 23 21 20 19 17 16 15 14 13 12 10 9 8 7 6 5 4 3 2 1 ITEM NO DESCRIPTION DWN CHK DIMENSIONS: ATLANTIC VERSION Shown on sheets 1 of 4 & 2 of 4 (Pacific version shown on sheets 3 of 4 AMP 4805 REV 31MAR2000 & 4 of 4) MATERIAL TOLERANCES UNLESS OTHERWISE SPECIFIED: 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH APVD NAME PRODUCT SPEC APPLICATION SPEC SIZE A1 WEIGHT SHEETS 3 CAGE CODE DRAWING NO RESTRICTED TO 00779 SCALE SHEET OF & 4 ARE NOT REQUIRED FOR ATLANTIC VERSION REV D C B A 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 6 5 4 3 2 RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. LOC 1 REVISIONS DIST ALL RIGHTS RESERVED. P LTR DESCRIPTION DATE DWN APVD FEED TYPE 37 62 239 40 D 59 247 38 56 246 39 250 260 44 252 245 35 249 63 238 53 163 166 6 81 59 82 1 136 70 137 C D 172 C 69 28 41 56 240 133 135 95 198 96 164 33 241 213 13 119 A 23 117 REF 12 67 24 B 17 66 26 19 237 20 15 B 16 21 14 25 54 24 REF ITEM 30 LOCATED AT FRONT HOLES 61 CAM POSITIONS 29 REF 27 29 47 48 121 93 46 32 8 60 FEED TRACK POSITION GUIDE BY WIRE BARREL 248 A A THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. DWN CHK 49 AMP 4805 REV 31MAR2000 49 49 DIMENSIONS: ATLANTIC VERSION Shown on sheets 1 of 4 & 2 of 4 (Pacific version shown on sheets 3 of 4 & 4 of 4) MATERIAL TOLERANCES UNLESS OTHERWISE SPECIFIED: 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH APVD NAME PRODUCT SPEC APPLICATION SPEC SIZE A1 WEIGHT SHEETS 3 CAGE CODE DRAWING NO RESTRICTED TO 00779 SCALE SHEET OF & 4 ARE NOT REQUIRED FOR ATLANTIC VERSION REV 7 8 THIS DRAWING IS UNPUBLISHED. C 5 4 3 2 RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. COPYRIGHT 6 PACIFIC VERSION TERMINATOR INTERFACE ADAPTER PART NUMBER REVISION 2- 2151842 -1 DESCRIPTION A 2- 2151842 -2 D SET UP GAUGE 2119599-1 ALL RIGHTS RESERVED. FEED TYPE FINE CRIMP HEIGHT ADJUST A FINE CRIMP HEIGHT ADJUST MECHANICAL PNEUMATIC 2- 2151842 -5 A FINE CRIMP HEIGHT ADJUST SERVO LATCH PLATE 2- 2151842 -7 A FINE CRIMP HEIGHT ADJUST NONE 7- 2151842 -7 A CRIMP TOOLING KIT - APPLICATOR STYLE CONVERSION CHART CONVERT TO PNEUMATIC FEED SERVO LATCH PLATE SMART APPLICATOR MECHANICAL FEED SERVO LATCH PLATE SMART APPLICATOR MECHANICAL FEED - PNEUMATIC FEED - CRIMP WIRE INSUL SIZE 2119950-1 1338683-1 2161326-1 - 2119951-1 2119949-1 2119951-1 2161326-1 2119949-1 2119950-1 - - 5-18022-5 - 8- 2151842 -5 8- 2151842 -4 1338683-1 5-18022-5 - 8- 2151842 -5 - 8- 2151842 -4 1338683-1 5-18022-5 1338683-1 5-18022-5 - - - - 2119641-2 2119799-1 - APPLICATOR INSTRUCTIONS 408-10389 - - 1901094-3 2119653-2 1901094-3 - 2119653-2 2119641-2 - - - 2168400-6 2168400-6 - 2119799-1 - (QUANTITY 2) - - - - - (QUANTITY 2) - - - - - 2063440-1 - - - - - - TYPE - INDAK TERMINAL TERMINAL DATA: WIRE STRIP LENGTH 3.54-3.84 mm [.139-.151 IN] C TERMINAL APPLICATION SPECIFICATION - TE CRIMP SPECIFICATION TERMINAL TERMINAL NAME: - INSULATION DIAMETER RANGE TE SPEC - - - - - - - - - TERMINALS APPLIED TE TERMINAL 2113311-1 - INDAK TERMINAL C1__DWG_PN_1_0 C81015 C1__DWG_PN_1_1 C1__DWG_PN_2_0 TE TERMINAL C1__DWG_PN_3_0 INDAK TERMINAL - C1__DWG_PN_4_0 - C1__DWG_PN_2_1 - WIRE SIZE 16 AWG 18 AWG 20 AWG CRIMP HEIGHT mm [INCH] W1__DWG_WGAUGE_1 W1__DWG_WGAUGE_2 W1__DWG_WGAUGE_3 1.88+/-0.05 [.074+/-.002] 1.80+/-0.05 [.071+/-.002] 1.73+/-0.05 [.068+/-.002] - CRIMP HEIGHT REFERENCE SETTING W1__DWG_CRIMP_HT_1 W1__DWG_CRIMP_HT_2 W1__DWG_CRIMP_HT_3 7.5 7.5 7.9 - W1__FA_SETTING_1 - W1__FA_SETTING_2 - W1__FA_SETTING_3 - - B - *WARNING ON INSTALLATION, SET WIRE DISC, ITEM 40 TO LARGEST WIRE SIZE SETTING. USE OF SETTINGS BELOW MINIMUM REQUIRED CRIMP HEIGHT SETTING WILL CAUSE DAMAGE TO CRIMP TOOLING. - - - - - A P LTR DESCRIPTION DATE DWN APVD 2063440-1 O - 2.79 mm [.110] REVISIONS DIST PART NUMBERS REQUIRED - APPLICATOR DATA LOC 1 1 - - 1 1 - 1 - - 1 1 2 - 1 1 1 1 1 1 1 1 1 1 - -77 -27 -25 -22 -21 2119782-1 2119640-1 2079988-1 1-22279-3 7-18023-7 2168400-6 2119580-1 2063440-1 PART NO FINE ADJUST HEAD ASM, PACIFIC STYLE PUSH ROD, AIR FEED BUSHING, LCH5-12, MISUMI SPRING, COMPRESSION SCR, SKT HD CAP M3 X 4.0 SHCS, LOW HEAD, RoHS, M5 X 16 MECHANICAL FEED ASSEMBLY AIR FEED MODULE DESCRIPTION 1 2119782 1 2119640-1 1 2079988_GATD 1 1-22279-3_SIMP 1 7-18023-7 2 2168400-6 1 2119580-1 1 2063440-1 - 251 250 249 246 241 240 239 238 1 1 ITEM NO 1 1 - 1 - 1 - - 1 1 REF 1 2 1 1-356885-4 2119740-2 1901094-3 21045-3 994969-1 994970-2 240638-1 8-21084-1 2119641-2 2119798-2 2079383-8 2168400-5 2119653-2 1-2119656-0 2119650-1 2119092-2 3-23627-7 2119799-1 SEE NOTE 4 1633743-1 1-22281-8 1-18028-2 2119944-1 1-690438-0 2168083-1 2168083-6 455888-5 1-240641-8 2119956-1 2119791-5 2119943-1 2119740-1 2168078-1 2119793-1 992763-5 2-18032-5 5-18022-5 1338683-1 2168083-8 18023-9 2119652-1 2079383-7 2119645-1 2119957-1 2119644-2 2168083-1 2161328-1 1901091-1 1-455888-0 22283-1 356835-1 240792-1 3-189124-3 980371-4 2168083-2 1-18028-2 2119533-1 690463-1 1-2168083-1 1-690464-5 2119862-1 2119806-1 3-22280-3 1-1633933-6 690468-1 2-459492-9 1 1 REF REF REF - - 1 1 - - 1 1 1 1 2 2 - - 1 1 1 1 1 1 - - - - - REF - 1 1 1 1 1 - REF 1 1 2 2 1 1 1 1 1 1 1 1 1 1 1 1 1 - 2 2 1 1 3 3 2 2 - - - - 2 2 - - - - 1 1 1 1 1 1 1 1 2 2 1 1 1 1 1 1 2 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 2 1 1 1 1 1 1 1 1 - - - - 1 1 - - 1 1 - - - - - - - - 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 2 1 3 2 1 1 2 1 1 1 1 1 2 1 1 1 2 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 2 1 3 2 1 1 2 2 1 1 1 1 1 2 1 1 1 2 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 PART NO -77 -27 -25 -22 -21 THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. STOP, SHEAR TAG,IDENTIFICATION SPACER, FEEDER RING, RETAIN, EXTERN, 3/16 CRESCENT MAGNET, RARE EARTH HIGH ENERGY COUNTER, MAGNETIC SPRING, FEED FINGER O-RING, .801 ID, .070 DIA. MAT. FEED CAM, AIR FEED DETENT PIN SCR, BHSC, RoHS (M4 X 16) SHCS, LOW HEAD, RoHS, M4 X 20 FEED CAM, POST FEED APPLICATOR BASIC ASSEMBLY, SF RAM, ASIAN STYLE, SIDE FEED BOLT, ADJUSTMENT PIN, RETAIN, GRVD, 3/16 X .854 HOLDER,FEED FINGER, AF MEMORY CHIP, PROGRAMMED SERVO FEED LATCH ASM SPRING, COMPRESSION WASHER, FLAT, REG M4 FEED FINGER ASSEMBLY,SF FRONT STRIP GUIDE SCR, SKT HD CAP, RoHS, M3 X 8.0 SCR, SKT HD CAP, RoHS, M5 X 65 SPACER, CRIMPER SPACER DOCUMENTATION PACKAGE DEPRESSOR, WIRE WASHER, SPACER TAG,IDENTIFICATION SCREW, DRIVE, RH, RoHS LIMITER, ADJUSTMENT BOLT SCR, SET, SOC, CONE POINT, M3 x 4.0 SCR, SET, FLT POINT M5 X 20.0 SCR, HEX HD CAP, M4 X 6.0 FEED PAWL SCR, SKT HD CAP, RoHS, M4 X 16 SCR, SKT HD CAP M4 X 6.0 FEED CAM, PRE FEED SCR, BHSC, RoHS (M8 X 25) DISC, NUMBERED FA WIRE ADJUSTMENT APPLICATOR SHIM PACK RAM WASHER, PRECISION SCR, SKT HD CAP, RoHS, M3 X 8.0 HEX HEAD, FLANGED, M5 x 8mm LONG PLATE, REAR STRIP GUIDE SPACER, CRIMPER SPRING, COMPRESSION LEVER, DRAG RELEASE DRAG, TERMINAL GUIDE, FRONT STRIP SCR, SKT HD SHLDR 5.0 DIA X 6.0 SCR, SKT HD CAP, RoHS, M4 X 8.0 WASHER, FLAT, REG M4 STRIPPER, SIDE FEED FLOATING SHEAR, REAR SCR, SKT HD CAP, RoHS, M3 X 6 SHEAR PLATE, REAR SHEAR HOLDER, REAR INSERT, SHEAR SPRING, COMPRESSION ANVIL, COMBINATION DEPRESSOR SHEAR, REAR CRIMPER, WIRE O 1 1-356885-4 1 2119740-2 .. 1 1901094-3 2 21045-3 1 994969-1_GATD 1 COUNTER_994970 1 240638 1 8-21084-1_GATD 1 2119641-2 1 2119798-2 1 2079383-8 2 2168400-5 1 2119653-2 1 1-2119656-0 1 2119650 1 2119092-2 1 3-23627-7 1 2119799 1 1901689_EMPTY_OCEAN_SF .. 1 1633743-1 1 1-22281-8 1 1-18028-2 1 2119944-1 1 1-690438-0 2 2168083-1 1 2168083-6 1 455888-5 1 1-240641-8 1 2119956-1 1 2119791-5 1 2119943-1 1 2119740-1 2 2168078-1 1 2119793 3 992763-5 2 2-18032-5 1 5-18022-5 1 1338683-1 2 2168083-8 3 18023-9 1 2119652 1 2079383-7 1 2119645 1 2119957-1 1 2119644-2 2 2168083-1 1 2161328 1 1901091-1 1 1-455888-0 2 22283-1 1 356835-1 1 240792-1 1 3-189124-3 1 980371-4 1 2168083-2 1 1-18028-2 1 2119533 1 690463-1 2 1-2168083-1 1 1-690464-5 1 2119862 1 2119806 1 SIMP_3-22280-3 .. 1 ITEM_10 .. 1 ITEM_9 1 1-1633933-6 .. 1 ITEM_7 1 690468-1 .. 1 ITEM_5 .. 1 ITEM_4 .. 1 ITEM_3 .. 1 ITEM_2 1 2-459492-9 237 213 198 172 166 164 163 152 151 145 144 143 142 141 140 139 137 136 135 133 121 119 117 96 95 93 82 81 71 70 69 67 66 63 62 61 59 56 53 49 48 41 40 39 38 33 32 29 28 27 26 25 24 23 21 20 19 17 16 15 14 13 12 10 9 8 7 6 5 4 3 2 1 ITEM NO DESCRIPTION DWN CHK DIMENSIONS: PACIFIC VERSION Shown on sheets 3 of 4 & 4 of 4 (Atlantic version shown on sheets 1 of 4 AMP 4805 REV 31MAR2000 & 2 of 4) MATERIAL TOLERANCES UNLESS OTHERWISE SPECIFIED: 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH APVD NAME PRODUCT SPEC APPLICATION SPEC SIZE A1 WEIGHT SHEETS 1 CAGE CODE DRAWING NO RESTRICTED TO 00779 SCALE SHEET OF & 2 ARE NOT REQUIRED FOR PACIFIC VERSION REV D C B A 7 8 THIS DRAWING IS UNPUBLISHED. C 5 4 3 2 RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. COPYRIGHT 6 LOC 1 REVISIONS DIST ALL RIGHTS RESERVED. P FEED TYPE LTR DESCRIPTION DATE DWN APVD 251 62 40 145 38 D 239 39 59 D 246 140 152 56 139 250 166 249 238 63 53 6 163 81 59 136 82 1 137 C 70 172 69 28 56 240 133 135 198 41 95 17 96 164 66 12 33 67 241 24 213 A 13 119 19 237 20 23 B 117 REF C B 16 21 26 15 14 25 143 61 CAM POSITIONS 142 24 ITEM 30 LOCATED AT FRONT HOLES REF 29 27 151 29 121 93 141 32 8 REF 144 FEED TRACK POSITION GUIDE BY WIRE BARREL 48 A A THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. 49 49 49 PACIFIC VERSION Shown on sheets 3 of 4 & 4 of 4 (Atlantic version shown on sheets 1 of 4 CHK DIMENSIONS: & 2 of 4) MATERIAL AMP 4805 REV 31MAR2000 DWN TOLERANCES UNLESS OTHERWISE SPECIFIED: 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH APVD NAME PRODUCT SPEC APPLICATION SPEC SIZE A1 WEIGHT SHEETS 1 CAGE CODE DRAWING NO RESTRICTED TO 00779 SCALE SHEET OF & 2 ARE NOT REQUIRED FOR PACIFIC VERSION REV