2.0x1.25mm SMD CHIP LED LAMP Part Number: APTK2012SURCK-F01 Hyper Red Features Description z 2.0mmx1.25mm SMT LED, 0.75mm THICKNESS. The Hyper Red source color devices are made with DH z LOW POWER CONSUMPTION. InGaAlP on GaAs substrate Light Emitting Diode. z WIDE VIEWING ANGLE. z IDEAL FOR BACK LIGHT AND INDICATOR. z VARIOUS COLORS AND LENS TYPES AVAILABLE. z PACKAGE : 2000PCS / REEL. z MOISTURE SENSITIVITY LEVEL : LEVEL 4. z RoHS COMPLIANT. Package Dimensions Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.1(0.004") unless otherwise noted. 3. Specifications are subject to change without notice. 4. The device has a single mounting surface. The device must be mounted according to the specifications. SPEC NO: DSAF1347 REV NO: V.3 APPROVED: WYNEC CHECKED: Allen Liu DATE: MAY/08/2007 DRAWN: Y.L.LI PAGE: 1 OF 5 ERP: 1204000331 Selection Guide Part No. Dice APTK2012SURCK-F01 Lens Type Hyper Red (InGaAlP) WATER CLEAR Viewing Angle [1] Iv (mcd) [2] @ 20mA Min. Typ. 2θ1/2 70 200 100° Notes: 1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 the optical centerline value. 2. Luminous intensity/ luminous Flux: +/-15%. Electrical / Optical Characteristics at TA=25°C Symbol Parameter Device Typ. λpeak Peak Wavelength Hyper Red λD [1] Dominant Wavelength Δλ1/2 Max. Units Test Conditions 650 nm IF=20mA Hyper Red 635 nm IF=20mA Spectral Line Half-width Hyper Red 28 nm IF=20mA C Capacitance Hyper Red 35 pF VF=0V;f=1MHz VF [2] Forward Voltage Hyper Red 1.95 2.5 V IF=20mA IR Reverse Current Hyper Red 10 uA VR=5V Notes: 1.Wavelength: +/-1nm. 2. Forward Voltage: +/-0.1V. Absolute Maximum Ratings at TA=25°C Parameter Hyper Red Units Power dissipation 75 mW DC Forward Current 30 mA Peak Forward Current [1] 185 mA 5 V Reverse Voltage Operating Temperature -40°C To +85°C Storage Temperature -40°C To +85°C Note: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. SPEC NO: DSAF1347 REV NO: V.3 APPROVED: WYNEC CHECKED: Allen Liu DATE: MAY/08/2007 DRAWN: Y.L.LI PAGE: 2 OF 5 ERP: 1204000331 Hyper Red APTK2012SURCK-F01 SPEC NO: DSAF1347 REV NO: V.3 APPROVED: WYNEC CHECKED: Allen Liu DATE: MAY/08/2007 DRAWN: Y.L.LI PAGE: 3 OF 5 ERP: 1204000331 APTK2012SURCK-F01 Recommended Soldering Pattern (Units : mm; Tolerance: ± 0.1) Tape Specifications (Units : mm) SPEC NO: DSAF1347 REV NO: V.3 APPROVED: WYNEC CHECKED: Allen Liu DATE: MAY/08/2007 DRAWN: Y.L.LI PAGE: 4 OF 5 ERP: 1204000331 PACKING & LABEL SPECIFICATIONS SPEC NO: DSAF1347 REV NO: V.3 APPROVED: WYNEC CHECKED: Allen Liu APTK2012SURCK-F01 DATE: MAY/08/2007 DRAWN: Y.L.LI PAGE: 5 OF 5 ERP: 1204000331