A1S thru A7S Surface Mount Glass Passivated Standard Rectifier Reverse Voltage 50~1000V Forward Current 1A Features • • • • • • • • Glass passivated Standard Rectifiers Very low profile - typical height of 1.0 mm Low forward voltage g drop p Low leakage current Moisture sensitivity: level 1, per J-STD-020 AEC-Q101 qualified High temperature soldering guaranteed: 260℃/10 seconds Halogen-free according to IEC 61249-2-21 definition eSGA (SOD‐123FL) Typical Applications For use of general purpose rectification in lighting, cellular phone, portable device, power supplies and other consumer applications. Maximum Ratings (TA = 25 °C unless otherwise noted) Parameter Symbol A1S A2S A3S A4S A5S A6S A7S Unit Maximum repetitive peak reverse voltage Maximum RMS voltage Maximum DC blocking voltage Maximum average forward rectified current at TL (See Fig.1) Peak forward surge current 8.3 ms single half sinewave superimposed on rated load VRRM VRMS VDC 50 35 50 100 70 100 200 140 200 400 280 400 600 420 600 800 560 800 1000 700 1000 V V V Operating junction and storage temperature range Electrical Characteristics Parameter Maximum instantaneous forward 1A voltage Typical reverse recovery time Typical junction capacitance Typical thermal resistance 1) 1.0 A IFSM 50 A TJ, TSTG - 55 to + 150 °C (TA = 25 °C unless otherwise noted) Test Conditions Maximum DC reverse current at rated DC blocking voltage IF(AV) TA=25℃ TA=125℃ IF=0.5A,IR=1.0A, Irr=0.25A 4.0 V, 1 MHz juntion to ambient juntion to case juntion to mount Symbol VF IR A1S A2S A3S A4S A5S A6S 1.1 A7S Unit Volts 5 µA 500 trr 1.8 uS CJ 6 pF RθJA RθJC RθJM 63 22 ℃/W 2 Note:1),The thermal resistance from junction to ambient,case or mount,mounted on P.C.B with 5×5mm copper pads,2 OZ,FR4 PCB www.goodark.com 1/4 2014.08-Rev.A A1S thru A7S Surface Mount Glass Passivated Standard Rectifier Reverse Voltage 50~1000V Forward Current 1A Ratings and Characteristics Curves (TA = 25℃ unless otherwise noted) Figure 2.Maximum Non‐Repetitive Peak Forward Surge Current Figure 1.Forward Current Derating Curve Figure 3. Typical Reverse Characteristics Figure 4. Typical Junction Capacitance Figure 5. Typical Instantaneous Forward Characteristics www.goodark.com 2/4 2014.08-Rev.A A1S thru A7S Surface Mount Glass Passivated Standard Rectifier Reverse Voltage 50~1000V Forward Current 1A Package Outline Dimensions Unit: mm DIM Unit: inch MIN MAX MIN MAX A 0.9 1.08 0.035 0.043 A1 0 0.1 0.000 0.004 B 0.85 1.05 0.033 0.041 C 0.1 0.25 0.004 0.010 D 1.7 2 0.067 0.079 E 2.9 3.1 0.114 0.122 L 0.43 0 43 0.83 0 83 0.017 0 017 0.033 0 033 HE 3.5 3.9 0.138 0.154 Soldering footprint Packing Information Packing quantities: 3000 pcs/Reel, 40 Reels/Box; 8mm Tape, 7" Reel Tape & Reel Specification www.goodark.com 3/4 2014.08-Rev.A A1S thru A7S Surface Mount Glass Passivated Standard Rectifier Reverse Voltage 50~1000V Forward Current 1A Disclaimers These materials are intended as a reference to assist our customers in the selection of the Suzhou Good-Ark product best suited to the customer’s application; they do not convey any license under any intellectual property rights, rights or any other rights, rights belonging to Suzhou Good-Ark Good Ark Electronics Co., Co Ltd.or a third party. Suzhou Good-Ark Electronics Co., Ltd. assumes no responsibility for any damage, or infringement of any third-party’s rights, originating in the use of any product data, diagrams, charts, programs, algorithms, or circuit application examples contained in these materials. All information contained in these materials, including product data, diagrams, charts, programs and algorithms represents information on products at the time of publication of these materials, and are subject to change by Suzhou Good-Ark Electronics Co., Ltd. without notice due to product improvements or other reasons. It is therefore recommended that customers contact Suzhou GoodArk Electronics Co., Ltd. or an authorized Suzhou Good-Ark Electronics Co., Ltd. for the latest product information before purchasing a product listed herein. The information described here may contain technical inaccuracies inacc racies or typographical t pographical errors. errors Suzhou S ho Good-Ark Good Ark Electronics Co., Co Ltd. Ltd assumes no responsibility for any damage, liability, or other loss rising from these inaccuracies or errors. Please also pay attention to information published by Suzhou Good-Ark Electronics Co., Ltd. by various means, including our website home page. (http://www.goodark.com) When using any or all of the information contained in these materials, including product data, diagrams, charts, programs, and algorithms, Please be sure to evaluate all information as a total system before making a final decision on the applicability of the information and products. Suzhou Good-Ark Electronics Co., Ltd. assumes no responsibility for any damage, liability or other loss resulting from the information contained herein. The prior written approval of Suzhou Good-Ark Electronics Co., Ltd. is necessary to reprint or reproduce d in i whole h l or in i partt these th materials. t i l Please contact Suzhou Good-Ark Electronics Co., Ltd. or an authorized distributor for further details on these materials or the products contained herein. www.goodark.com 4/4 2014.08-Rev.A