ATMEL AT88SC018-SU-CM-T Cryptocompanionâ ¢ chip for cryptomemory and cryptorf Datasheet

Features
• Companion Chip to CryptoRF® and CryptoMemory®
⎯ Securely implements host algorithms
⎯ Securely stores host secrets
⎯ Verifies Host Firmware Digests
• High Security Features in Hardware
⎯ CryptoMemory and CryptoRF F2 Algorithm
⎯ SHA-1 Standard Cryptographic Algorithm
⎯ 64-bit Mutual Authentication Protocol (Under License of ELVA)
⎯ Permanently Coded Serial Numbers
⎯ High Quality Random Number Generator (RNG)
⎯ Metal Shield Over Memory
CryptoCompanion™
Chip for
CryptoMemory and
CryptoRF
⎯ Data Scrambling in Nonvolatile Memory
⎯ Delay Penalties to prevent Systematic Attacks
AT88SC018
⎯ Reset Locking to prevent Illegal Power Cycling
⎯ Voltage and Frequency Monitors
• Host-side Crypto Functions
Summary
⎯ Authentication Challenge Generation
⎯ Device Challenge Response
⎯ Message Authentication Codes (MAC) Generation
⎯ Data Encryption and Decryption
⎯ Secure Authentication Key Management
• Secure Storage and Key Management
⎯ Up to 16 sets of 64-bits Diversified Host Keys
⎯ Eight Sets of Two 24-bit Passwords
⎯ Secure and Custom Personalization
⎯ Up to 232-Byte Read/Write Configurable User Data Area
• Nonvolatile Up Counters
⎯ Four sets Unidirectional Counters
⎯ 6.4 Million Maximum Counts Per Counter
• Application Features
⎯ Low Voltage Supply: 2.7V – 3.6V
⎯ 2-Wire Serial Interface (TWI, 5V Compatible)
⎯ Standard 8-lead SOIC Plastic Package, Green compliant (exceeds RoHS)
• High Reliability
⎯ Endurance
⎯ Data Retention
: 100,000 Cycles
: 10 years
⎯ ESD Protection
: 3,000 V min. HBM
5277DS–CryptoCompanion–9/09
1.
Product Overview
The CryptoCompanion™ Chip is designed as the mate to Atmel’s CryptoRF and CryptoMemory chips, collectively
referred to in the remainder of this document as CRF.
CryptoCompanion
makes
extensive
use
of
the
SHA-1
hash
algorithm
as
specified
in
http://www.itl.nist.gov/fipspubs/fip180-1.htm and elsewhere. In this document, the nomenclature SHA-1(a, b, c) means
to concatenate a, b & c in that order and then pad them to a block size of 64 bytes before computing the digest.
CryptoCompanion generates SHA-1 digests of single round datasets at a time.
1.1.
General Operation
The CRF chip contains secrets that must be known or derived by a host system in order to establish a trusted link
between the two and permit communications to happen. CryptoCompanion stores these secrets in an obscured way in
nonvolatile memory and contains all the circuitry necessary to perform the authentication, password and
encryption/decryption functions specified in the CRF datasheet. In this manner, the secrets do not ever need to be
revealed.
The general cryptographic strategy is as follows:
1.2.
•
Each CRF chip has a serial or identification number (ID) and authentication secret Gi stored in EEPROM. ID is
freely readable while Gi can never be read and is unique for all tags.
•
CryptoCompanion contains an EEPROM that holds a set of common secrets (Fn). CryptoCompanion combines Fn
with ID and KID to compute a value of G that is expected to match that in the CRF chip. Specifically, G = SHA-1(Fn,
ID, KID)
•
G is further diversified by the inclusion of a number (KID) generated by the host system in a manner of its choosing.
Typically, it will be the result of a cryptographic operation on the CRF ID value calculated using other data, secrets
and/or algorithms external to CryptoCompanion. This permits scenarios that offer varying degrees of additional
security.
•
CryptoCompanion includes a general purpose cryptographic quality random number generator which is used to
seed a mutual authentication process between CryptoCompanion and CRF. If the CRF confirms the
CryptoCompanion challenge, and the CryptoCompanion confirms the CRF response, then the host system
proceeds with CRF operations. In this way the host system may use the CRF without knowing the CRF's secrets
directly.
CryptoCompanion Benefits
The following is a partial list of the benefits of using this chip versus storing the algorithms and secrets in standard
FLASH system memory.
2
•
Keep confidential those core secrets that are used to authenticate with and communicate to/from CRF.
(Store them in EEPROM, use them on-chip)
•
Flexible system implementation – multiple secrets and policies for different CRF locations within the system.
Multiple manufacturer setup options.
•
Hardware encryption engines, avoids algorithm disclosure from reverse-compilation of system operating code.
•
Full hardware security implementation makes it harder for an attacker (even with lab equipment) to get secrets
stored on CryptoCompanion.
•
Global secrets are protected using strong security, standard algorithm (SHA-1).
•
Robust random number generation avoids accidental replay for all cryptographic operations using the system, not
just with respect to CRF.
•
Secure EEPROM storage for configuration information, etc. May permit reduction in the total BOM for the system.
•
Easy to use – little programming required; no knowledge of security algorithms or protocols, fast time to market.
CryptoCompanion™ Chip
5277DS–CryptoCompanion–9/09
CryptoCompanion™ Chip
1.3.
Package, Pin Definition & IO
1.3.1.
Pin Definition
1.3.1.1. VCC , Gnd
Power supply is 2.7 – 3.6V. Supply current less than 5 mA.
CryptoCompanion will be available to accept commands 60 ms after the later of VCC rising above 2.7V or Reset being
driven high if CryptoCompanion is in a security delay then this interval is significantly longer.
During Power Up, VCC must exhibit a monotonic ramp at a minimum rate of 50 mV/mS until VCC has crossed the 2.7V
level. During Power Down, VCC must exhibit a monotonic ramp at a minimum rate of 50 mV/mS once it has dropped
below the 2.5V boundary. CryptoCompanion does not support hot swapping or hot plugging.
VCC must be bypassed with high quality surface mount capacitors that are properly located on the board. Atmel
recommends two capacitors connected in parallel having a value of 1μF and 0.01μF. The capacitors should be
manufactured using X5R or X7R dielectric material. These capacitors should be connected to CryptoCompanion using
a total of no more than 1cm PC board traces. Atmel recommends the use of a ground plane and a trace length of less
than 0.5cm between the capacitors and the VCC pin. Failure to follow these recommendations may result in improper
operation.
1.3.1.2. SDA
Two wire interface data pin, 5 V compatible. Minimum data setup time = 0.1 μs, and minimum data hold time = 0 μs min.
The system board must include an external pull-up resistor.
1.3.1.3. SCL
Two wire interface clock pin, 5 V compatible. Maximum SCL rate is 400KHz, minimum TLOW = 1.2 μs, minimum
THIGH = 0.6 μs. The system board must include an external pull-up resistor.
1.3.1.4. Reset (RST)
This active low input will reset all states within CryptoCompanion. Honored regardless of the state of PowerDown.
1.3.1.5. PowerDown (PDN)
When held low, the part operates normally. When held high the part will go to sleep and ignore all transitions on SDA
and SCL, power consumption will drop to less than 10 μA. There is a 50 ms delay between this pin falling and the first
transition on SDA or SCL that will be accepted by the chip.
3
5277DS–CryptoCompanion–9/09
1.3.2.
Package
CryptoCompanion is packaged in an 8 lead SOIC package with the following pin definition:
Table 1.
8 lead SOIC package pin definition
Pin Number
Pin Name
1
VCC
5
Gnd
7
SDA
8
SCL
4
RST
3
PDN
2,6
NC
Pins 2 & 6 are not internally connected and should be connected to ground on the PC board.
1.3.3.
Figure 1.
Connection Diagram
Connection Diagram
2.7v - 5.5v
2.7v - 3.6v
Microprocessor
CryptoCompanion
SDA
SCL
1.3.4.
Environmental
CryptoCompanion is guaranteed to operate over the industrial temperature range of -40° to 85° C. ESD is rated at 3KV,
Human Body Model.
1.3.5.
TWI Input/Output Operation
CryptoCompanion communicates to the system using a two wire interface (TWI), which is similar to SMBus. The chip
operates as a slave and does not support clock stretching. This two wire protocol is identical to that supported by the
Atmel AT24C16B serial EEPROM chips. Please see that datasheet on the Atmel web site for detailed timing and
protocol information.
4
CryptoCompanion™ Chip
5277DS–CryptoCompanion–9/09
CryptoCompanion™ Chip
The system processor is expected to properly format commands for CryptoCompanion (which may include information
from the CRF chip), and then process the outputs of CryptoCompanion (which may include sending some of the
outputs to the CRF chip).
CryptoCompanion cannot directly communicate with CRF chips. Both CRF and CryptoCompanion are slave devices.
The bus master may use one or two busses to communicate with them. Separate TWI addresses must be used if both
chips are on the same bus.
1.4.
Memory Locking
When this initialization is complete the Lock command should be executed which limits access to the memory per the
restrictions listed later in this section. The system can determine the current lock value by using the
ReadManufacturingID command to read out the ManufacturingID value (MfrID) and the lock byte.
The table below describes the encoding of the least significant two bits of the Lock byte. On shipment from Atmel,
Lock[1:0] will have a value of either 10 or 00, depending on the part number ordered. An AT88SC018 in either of these
two states is considered ‘unlocked’. It is not possible to change from one of these unlocked states to the other.
After the Lock command has been executed, the Lock byte will have the value 0xFF. Subsequent changes to the Lock
byte are impossible.
Table 2.
2.
Memory Locking
LockBit 1
Lock Bit 0 (LSB)
Meaning
1
1
Locked. ReadMemory & WriteMemory enabled, subject to the restrictions in this
section. WriteMemoryEncrypted and ReadMemoryDigest disabled.
1
0
Unlocked/Confidential. ReadMemoryDigest, WriteMemory and
WriteMemoryEncrypted enabled. ReadMemory disabled.
0
0
Unlocked. ReadMemory & WriteMemory enabled. WriteMemoryEncrypted and
ReadMemoryDigest disabled.
AC & DC Characteristics
Table 3.
DC Characteristics (1)
Applicable over recommended operating range from VCC = +2.7 to 3.6 V,
TAC = -40o C to 85o C (unless otherwise noted)
Symbol
Parameter
Test Condition
Min
2.7
Typ
Max
Units
VCC
ICC
Supply Voltage
Supply Current
400kHz
3.6
5
V
mA
ISB
Standby Current
VIN = VCC or GND
15
μA
VIL
SDA Input Low Voltage
-0.3
VCC x 0.3
V
VIL
CLK Input Low Voltage
-0.3
VCC x 0.3
V
VIL
RST Input Low Voltage
-0.3
VCC x 0.3
V
VIL
PDN Input Low Voltage
-0.3
VCC x 0.3
V
VIH
SDA Input High Voltage
VCC x 0.7
5.25
V
VIH
SCL Input High Voltage
VCC x 0.7
5.25
V
VIH
RST Input High Voltage
VCC x 0.7
5.25
V
5
5277DS–CryptoCompanion–9/09
VIH
PDN Input High Voltage
VCC x 0.7
5.25
V
IIL
SDA Input Low Current
0 < VIL < VCC x 0.15
-10
10
μA
IIL
SCL Input Low Current
0 < VIL < VCC x 0.15
-10
10
μA
IIL
RST Input Low Current
0 < VIL < VCC x 0.15
-10
10
μA
IIL
PDN Input Low Current
0 < VIL < VCC x 0.15
-10
10
μA
IIH
SDA Input High Current
VCC x 0.7 < VIH < VCC
-10
10
μA
IIH
SCL Input High Current
VCC x 0.7 < VIH < VCC
-10
10
μA
IIH
RST Input High Current
VCC x 0.7 < VIH < VCC
-10
10
μA
IIH
PDN Input High Current
-10
10
μA
VOH
SDA Output High Voltage
VCC x 0.7 < VIH < VCC
20k Ohm external
Pull-up
VCC x 0.8
V
VOL
SDA Output Low Voltage
IOL = 1mA
0.4
V
Note: 1. Typical values at 25° C. Maximum values are characterized values and not test limits in production.
6
CryptoCompanion™ Chip
5277DS–CryptoCompanion–9/09
CryptoCompanion™ Chip
Table 4.
AC Characteristics (1)
Applicable over recommended operating range from VCC = +2.7 to 3.6 V,
o
o
TAC = -40 C to 85 C, CL = 30pF (unless otherwise noted)
Symbol
Parameter
fCLK
Clock Frequency
Clock Duty cycle (2)
tR
Rise Time - SDA, RST, PDN (2)
tF
tR
Fall Time - SDA, RST, PDN
Rise Time - SCL
Min
Max
Units
0
40
400
60
kHz
%
300
nS
300
nS
300
nS
300
nS
900
nS
(2)
(2)
(2)
tF
Fall Time - SCL
tAA
Clock Low to Data Out Valid
tHD.STA
Start Hold Time
600
nS
tSU.STA
Start Set-up Time
600
nS
tHD.DAT
Data In Hold Time
100
nS
tSU.DAT
Data In Set-up Time
100
nS
tSU.STO
Stop Set-up Time
600
nS
tDH
Data Out Hold Time
50
900
nS
Note: 1. Typical values at 25° C. Maximum values are characterized values and not test limits in production.
2. This parameter is not tested. Values are based on characterization and/or simulation data.
Figure 2. SCL: Serial Clock, SDA: Serial Data I/O®
7
5277DS–CryptoCompanion–9/09
3.
Ordering Codes
Table 5.
Ordering Codes
Voltage
Range
AT88SC018-SU-CM
8S1
2.7V – 3.6V
00 (Unlocked)
Green compliant (exceeds
RoHS), Industrial (-400 C – 850
C), Bulk
AT88SC018-SU-CM-T
8S1
2.7V – 3.6V
00 (Unlocked)
Green compliant (exceeds
RoHS), Industrial (-400 C – 850
C), Tape and Reel
AT88SC018-SU-CN
8S1
2.7V – 3.6V
10 (Unlocked/Confidential)
Green compliant (exceeds
RoHS), Industrial (-400 C – 850
C), Bulk
AT88SC018-SU-CN-T
8S1
2.7V – 3.6V
10 (Unlocked/Confidential)
Green compliant (exceeds
RoHS), Industrial (-400 C – 850
C), Tape and Reel
Table 6.
(see
Section 1.4 for Lock Definitions)
Temperature Range
Package Type
Package Type
8S1
8
Memory Locking
Package
Ordering Code
Description
8-lead, 0.150” Wide, Plastic Gull Wing Small Outline Package (JEDEC SOIC)
CryptoCompanion™ Chip
5277DS–CryptoCompanion–9/09
CryptoCompanion™ Chip
4.
Package Drawing
Figure 3.
8S1 – SOIC
9
5277DS–CryptoCompanion–9/09
5.
10
Revision History
Doc. Rev.
Date
Comments
5277DS
09/2009
Finalized AC & DC Charateristics. Updated Counter information.
5277CS
02/2009
Document updated.
5277BS
12/2008
Document updated.
CryptoCompanion™ Chip
5277DS–CryptoCompanion–9/09
Headquarters
International
Atmel Corporation
Atmel Asia
Atmel Europe
Atmel Japan
2325 Orchard Parkway
San Jose, CA 95131
USA
Tel: 1(408) 441-0311
Fax: 1(408) 487-2600
Room 1219
Chinachem Golden Plaza
77 Mody Road Tsimshatsui
East Kowloon
Hong Kong
Tel: (852) 2721-9778
Fax: (852) 2722-1369
Le Krebs
8, Rue Jean-Pierre Timbaud
BP 309
78054 Saint-Quentin-enYvelines Cedex
France
Tel: (33) 1-30-60-70-00
Fax: (33) 1-30-60-71-11
9F, Tonetsu Shinkawa Bldg.
1-24-8 Shinkawa
Chuo-ku, Tokyo 104-0033
Japan
Tel: (81) 3-3523-3551
Fax: (81) 3-3523-7581
Web Site
Technical Support
Sales Contact
www.atmel.com
[email protected]
[email protected]
www.atmel.com/contacts
Product Contact
Literature Requests
www.atmel.com/literature
Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any
intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND
CONDITIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR
STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS
FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL,
PUNITIVE, SPECIAL OR INCIDEN-TAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION,
OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this document
and reserves the right to make changes to specifications and product descriptions at any time without notice. Atmel does not make any commitment to update the
information contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel’s
products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life.
© 2009 Atmel Corporation. All rights reserved. Atmel®, Atmel logo and combinations thereof, CryptoMemory®, CryptoRF®, and others are registered trademarks,
CryptoCompanion™, and others are trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others.
5277DS–CryptoCompanion–09/09
Similar pages