Click on Series name for product info on aimtec.com Series AME1-JZ 1Watt | AC-DC / DC-DC Converter FEATURES: Picture coming soon • • • • • Class II Power supply • Energy Star compliant • Ultra-small package I/O Isolation 3000VAC Operating Temp: -25°C to +70°C Input: 85-305VAC, 47-63Hz, or 120-430 VDC Over current, Short Circuit Protection Models Single output Model Input Voltage (VAC/Hz) Input Voltage (VDC) Temperature range (ºC) Output Voltage (V) Output Current max (mA) Maximum capacitive Load (µF) Efficiency (%) 85-305/47-63 85-305/47-63 85-305/47-63 85-305/47-63 85-305/47-63 85-305/47-63 120-430 120-430 120-430 120-430 120-430 120-430 -25 to +70 -25 to +70 -25 to +70 -25 to +70 -25 to +70 -25 to +70 3.3 5 9 12 15 24 300 200 111 83 67 42 4000 4000 2200 2200 1000 680 63 68 72 73 74 75 AME1-3.3SJZ AME1-5SJZ AME1-9SJZ AME1-12SJZ AME1-15SJZ AME1-24SJZ Input Specifications Parameters Current (full load) Inrush current <2ms (cold start) Leakage current External fuse Output Specifications Parameters Voltage accuracy Line regulation Load regulation Minimum load Ripple & Noise* Conditions Typical 115 VAC 230 VAC 115 VAC 230 VAC 5 11 Recommended slow blow type 1 Maximum 30 17 Conditions Typical ±6 ±2 ±5 10 100 3.3/5 VDC With 560µF E/C VAC Units mA mA A A mA A 0.15 Full load, nominal input LL-HL, Full Load 10% - 100% load, nominal input 230 Maximum Units 200 % % % % mV p-p Rated Units 3000 VAC MΩ Maximum Units *Ripple &Noise measured at 20MHz bandwidth with 1µF C/C and 10µF E/C and 115/230VAC with Full Load. Isolation Specifications Parameters Tested I/O voltage Isolation Resistance General Specifications Parameters Switching frequency Over Current protection Short circuit protection Operating temperature Storage temperature Maximum Case temperature Humidity Case material Weight Cooling Dimensions (L x W x H) MTBF Conditions Typical 60 sec >1000 Conditions Typical 100 ≥110% Auto recovery Auto recovery With derating above 55°C KHz -25 to +70 -40 to +85 100 Non condensing 20 ~ 90 Plastic resin (flammability to UL 94V-0) 20 Free air convection 1.33 x 0.87 x 0.71 (33.70 x 22.20 x 18.00mm) > 300,000 hrs (MIL-HDBK -217F, t=+25oC)/Full Load °C °C °C % RH g NOTE: All specifications in this datasheet are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. www.aimtec.com F 052e R8 Tel: +1 514 620 2722 1 of 3 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AME1-JZ 1Watt | AC-DC / DC-DC Converter Safety Specifications Parameters Approvals Standards cULus, CE pending Information technology Equipment EMI - Conducted and radiated emission Electrostatic Discharge Immunity RF, Electromagnetic Field Immunity Electrical Fast Transient/Burst Immunity Surge Immunity(1KV) RF, Conducted Disturbance Immunity Power frequency Magnetic Field Immunity Voltage dips, Short Interruptions Immunity Meets IEC/EN/UL 60950-1:2006+A11:2009 EN55022, class B, with application circuit IEC 61000-4-2, Contact:±4KV/Air:±8KV, Criteria B IEC 61000-4-3, 10V/m, Criteria A IEC 61000-4-4, ±2KV, Criteria B, with EMC recommended circuit IEC 61000-4-5, ±1KV/±2KV, Criteria B, with EMC recommended circuit IEC 61000-4-6, 10Vrms, Criteria A IEC 61000-4-8, 10A/m, Criteria A IEC 61000-4-11, 0-70%, Criteria B Pin Out Specifications Pin Single 1 2 3 4 Dimensions 16.85 (0.66) 33.70 (1.33) AC Input (N) AC Input (L) -V Output +V Output Top Vi ew 1 15.24 1 3 Top View (0.60) 7.60 (0.29) 4 Temperature m easuring point 11.00 3 (0.43) 22.00 4 (0.87) 2 2 28.00 DIV: 5.00(0.20) (1.10) Ø 10.0 ( Ø 0.40) Ø 0.60 ( Ø 0.02) 18.00 Side View (0.71) 6.00 (0.24) Derating Free Air Convection Dimensions mm (inch) Case Tolerance ±0.50 (±0.02) Pin Diameter ±0.10 (±0.004) Pin Pitch Tolerance ±0.50 (±0.02) 0.60 (0.02) 100 80 Safe Operating Area 60 50 40 20 0 - 25 -20 55 0 20 40 60 70 80 100 Ambient Temperature º C www.aimtec.com F 052e R8 Tel: +1 514 620 2722 2 of 3 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AME1-JZ 1Watt | AC-DC / DC-DC Converter Application circuit AC L FUSE 1A/300V Single Output NTC 4 AC L CX 0.1µF/ 305VAC MOV S14K350 AC N AC DC AC N + Vout C1 C2 1µF/50V + TVS 3 - Vout *GND connection not allowed EMC recommended circuit AC L FUSE 1A/300V MOV S14K350 AC N Single Output LCM 10mH NTC CY1 2.2nF/ 400VAC CX 0.1µF/ 305VAC CY2 2.2nF/ 400VAC 4 AC L AC AC N DC + Vout C1 1µF/50V 3 + TVS C2 - Vout GND Model 3.3 & 5 Vout 9 Vout 12 & 15 Vout 24 Vout C2 220 µF / 35V 120 µF / 35V 120 µF / 35V 68 µF / 35V TVS 7V 12V 20V 30V NOTE: 1. Datasheets are updated as needed and as such, specifications are subject to change without notice. Once printed or downloaded, datasheets are no longer controlled by Aimtec; refer to www.aimtec.com for the most current product specifications. 2. Product labels shown, including safety agency certifications on labels, may vary based on the date manufactured. 3. Mechanical drawings and specifications are for reference only. 4. All specifications are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. 5. Aimtec may not have conducted destructive testing or chemical analysis on all internal components and chemicals at the time of publishing this document. CAS numbers and other limited information are considered proprietary and may not be available for release. 6. This product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control systems or other such applications which necessitate specific safety and regulatory standards other the ones listed in this datasheet. 7. Warranty is in accordance with Aimtec’s standard Terms of Sale available at www.aimtec.com. www.aimtec.com F 052e R8 Tel: +1 514 620 2722 3 of 3 Toll free: + 1 888 9 AIMTEC (924 6832) North America only