1.6X1.25mm BI-COLOR SMD CHIP LED LAMP ATTENTION Part Number: APTB1612CGKQWDF OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DISCHARGE SENSITIVE DEVICES Green White Features Descriptions z 1.6mmx1.25mm SMD LED, 0.65mm thickness. z The Green source color devices are made with AlGaInP z Bi-color,low power consumption. on GaAs substrate Light Emitting Diode. z The source color devices are made with InGaN Light z Wide viewing angle. z Ideal for backlight and indicator. Emitting Diode. z Electrostatic discharge and power surge could damage z Package : 2000pcs / reel. z Moisture sensitivity level : level 3. the LEDs. z It is recommended to use a wrist band or anti- z RoHS compliant. electrostatic glove when handling the LEDs. z All devices, equipments and machineries must be electrically grounded. Package Dimensions GREEN WHITE Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.2(0.008") unless otherwise noted. 3.The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. 4.The device has a single mounting surface. The device must be mounted according to the specifications. SPEC NO: DSAL1001 REV NO: V.5B DATE: SEP/01/2015 PAGE: 1 OF 8 APPROVED: Wynec CHECKED: Allen Liu DRAWN: L.Q.Xie ERP: 1203011788 Selection Guide Part No. Emitting Color (Material) Iv (mcd) [2] @ 20mA Lens Type Green (AlGaInP) APTB1612CGKQWDF Viewing Angle [1] Min. Typ. 20 50 120 250 120° Yellow Fluorescent White (InGaN) 2θ1/2 Notes: 1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value. 2. Luminous intensity / luminous Flux: +/-15%. 3. Luminous intensity value is traceable to the CIE127-2007 compliant national standards. Electrical / Optical Characteristics at TA=25°C [Green] Symbol Parameter Emitting Color Typ. λpeak Peak Wavelength Green λD [1] Dominant Wavelength Δλ1/2 Max. Units Test Conditions 574 nm IF=20mA Green 570 nm IF=20mA Spectral Line Half-width Green 20 nm IF=20mA C Capacitance Green 15 pF VF=0V;f=1MHz VF [2] Forward Voltage Green 2.1 2.5 V IF=20mA IR Reverse Current Green 10 uA VR = 5V Notes: 1.Wavelength: +/-1nm. 2.Forward Voltage: +/-0.1V. 3.Wavelength value is traceable to the CIE127-2007 compliant national standards. 4.Excess driving current and/or operating temperature higher than recommended conditions may result in severe light degradation or premature failure. Electrical / Optical Characteristics at TA=25°C [White] Symbol Parameter Emitting Color Typ. Max. Units Test Conditions VF [1] Forward Voltage White 3.3 4.0 V IF=20mA IR Reverse Current White 50 uA VR = 5V pF VF=0V;f=1MHz x [2] 0.31 Chromaticity Coordinates White y [2] C 0.31 Capacitance White 100 Notes: 1.Forward Voltage: +/-0.1V. 2. Measurement Tolerance Of The Chromaticity Coordinates Is ±0.01. 3.Excess driving current and/or operating temperature higher than recommended conditions may result in severe light degradation or premature failure. SPEC NO: DSAL1001 REV NO: V.5B DATE: SEP/01/2015 PAGE: 2 OF 8 APPROVED: Wynec CHECKED: Allen Liu DRAWN: L.Q.Xie ERP: 1203011788 Absolute Maximum Ratings at TA=25°C Parameter Green White Units Power dissipation 75 120 mW DC Forward Current 30 30 mA Peak Forward Current [1] 150 150 mA Electrostatic Discharge Threshold (HBM) 3000 250 V Reverse Voltage 5 Operating Temperature -40°C To +85°C Storage Temperature -40°C To +85°C V Note: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. SPEC NO: DSAL1001 REV NO: V.5B DATE: SEP/01/2015 PAGE: 3 OF 8 APPROVED: Wynec CHECKED: Allen Liu DRAWN: L.Q.Xie ERP: 1203011788 APTB1612CGKQWDF Green SPEC NO: DSAL1001 REV NO: V.5B DATE: SEP/01/2015 PAGE: 4 OF 8 APPROVED: Wynec CHECKED: Allen Liu DRAWN: L.Q.Xie ERP: 1203011788 White SPEC NO: DSAL1001 REV NO: V.5B DATE: SEP/01/2015 PAGE: 5 OF 8 APPROVED: Wynec CHECKED: Allen Liu DRAWN: L.Q.Xie ERP: 1203011788 APTB1612CGKQWDF White CIE 0.40 c0 0.35 y b1 0.30 b2 a0 0.25 a2 0.20 0.20 0.25 0.30 0.35 0.40 x a2 b1 x y x y x y 0.263 0.213 0.282 0.245 0.298 0.271 0.282 0.245 0.298 0.271 0.313 0.296 0.265 0.265 0.286 0.299 0.306 0.332 0.242 0.226 0.265 0.265 0.286 0.299 0.313 0.296 0.329 0.325 0.329 0.325 0.358 0.372 0.329 0.371 0.363 0.400 0.306 0.332 0.329 0.371 a0 c0 b2 Notes: Shipment may contain more than one chromaticity regions. Orders for single chromaticity region are generally not accepted. Measurement tolerance of the chromaticity coordinates is ±0.01. SPEC NO: DSAL1001 REV NO: V.5B DATE: SEP/01/2015 PAGE: 6 OF 8 APPROVED: Wynec CHECKED: Allen Liu DRAWN: L.Q.Xie ERP: 1203011788 APTB1612CGKQWDF Reflow soldering is recommended and the soldering profile is shown below. Other soldering methods are not recommended as they might cause damage to the product. Recommended Soldering Pattern (Units : mm; Tolerance: ± 0.1) Reel Dimension Tape Dimensions (Units : mm) SPEC NO: DSAL1001 REV NO: V.5B DATE: SEP/01/2015 PAGE: 7 OF 8 APPROVED: Wynec CHECKED: Allen Liu DRAWN: L.Q.Xie ERP: 1203011788 PACKING & LABEL SPECIFICATIONS APTB1612CGKQWDF Terms and conditions for the usage of this document 1. The information included in this document reflects representative usage scenarios and is intended for technical reference only. 2. The part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. Before production usage customer should refer to the latest datasheet for the updated specifications. 3. When using the products referenced in this document, please make sure the product is being operated within the environmental and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible for any subsequent issues. 4. The information in this document applies to typical usage in consumer electronics applications. If customer's application has special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with Kingbright representative for further assistance. 5. The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright. 6. All design applications should refer to Kingbright application notes available at http://www.KingbrightUSA.com/ApplicationNotes SPEC NO: DSAL1001 REV NO: V.5B DATE: SEP/01/2015 PAGE: 8 OF 8 APPROVED: Wynec CHECKED: Allen Liu DRAWN: L.Q.Xie ERP: 1203011788