Small and high accuracy Temperature Sensor IC Series High Accuracy detection Thermostat Output Temperature Sensor ICs with Power Down Function No.09047ECT01 BDJ□□□1HFV Series ●Description BDJ□□□1HFV series is thermostat output temperature sensor IC with built-in temperature detection element,constant current circuit,high-accuracy reference voltage source in one chip.Temperature detection can be realized at ±2.5℃ accuracy without complicated design.It is the best temperature sensor IC for a portable equipment of micro and low current,the power down function, and the battery drive.It is possible to use it for a wide usage such as the heat detection and temperature monitors because it provides with the analog output in addition to the thermostat power output. BDJ□□□1HFV series has 8 types of model at 5℃ intervals from +55℃ to +90℃ temperature range. ●Features 1) Detection Temperature Range 55～90℃ by 5℃ Step 8 products. 2) Power supply Voltage range 2.4～5.5V. 3) High Accuracy thermostat ( typ.±1.0℃, max.±2.5℃ @Ta=55～90℃ ) 4) High Accuracy Analog Output ( typ.±1.0℃, max.±2.5℃ @Ta=-30～100℃ ) 5) Analog Output Temperature Sensitivity ( typ. -8.2mV/℃ ) 6) Low Supply Current ( typ. 7.5μA ) 7) Power down control function built in.(PD interface Voltage min 1.5V) 8) Small Package ( typ. 1.60mm×1.60mm×0.60mm ) 9) Low thermal resistance package ( typ. 187℃/W ) 10) ESD Rating 8kV ( HBM ) ●Applications Cell phone, Digital Camera,Thermal Protection for Electrical Equipment (NoteBook PC, FPD-TV, etc.) ●Line up matrix BDJ0901HFV 90 BDJ0851HFV 85 BDJ0801HFV 80 BDJ0751HFV 75 Open Drain Open Drain Open Drain Open Drain www.rohm.com © 2009 ROHM Co., Ltd. All rights reserved. Detect Temp. （℃） Product Name Active H gd BDJ0701HFV 70 Active H ge BDJ0651HFV 65 Active H gf BDJ0601HFV 60 Active H gg BDJ0551HFV 55 OS Output Format 1/9 OS Output Format Open Drain Open Drain Open Drain Open Drain Marking Detect Temp. （℃） Marking Product Name Active H gh Active H gk Active H gm Active H gn 2009.08 - Rev.C Technical Note BDJ□□□1HFV Series ● ABSOLUTE MAXIMUM RATINGS ( Ta = 25℃ ) PARAMETERS SYMBOL LIMIT Power Supply Voltage VDD -0.3 to 7.0*1 Input Voltage ( PD ) VIN -0.3 to VDD+0.3 OS terminal Voltage VOS -0.3 to 7.0*1 OS terminal Current IOS 5.0 Power dissipation Pd 536*2 Storage Temperature Range Tstg -55 to 150 *1. Not to exceed Pd *2. Reduced by 5.36mW for each increase in Ta of 1℃ over 25℃ （ mounted on 70mm×70mm×1.6mm Glass-epoxy PCB ） ● RECOMMENDED OPERATING CONDITION PARAMETERS SYMBOL Power Supply Voltage VDD Operating Temperature Range Topr MIN. 2.4 -30 TYP. 2.8 - MAX. 5.5 100 UNIT V V V mA mW ℃ UNIT V ℃ ● ELECTRICAL CHARACTERISTICS ( unless otherwise specified, VDD = 2.8V, Ta = 25℃ ) PARAMETER Supply Current Normal function mode Power Down mode PD Input L Voltage Input H Voltage PD Leakage Current Analog Output VTemp Output Voltage VTemp Temperature Sensitivity VTemp Load Regulation Vtemp VDD Regulation OS Output Open Drain OS Leakage Current OS Output Voltage Radiation hardiness is not designed. MIN. LIMIT TYP. MAX. IDD IDDPD - 7.5 0.3 12.0 1.0 μA μA PD="H" PD="L" VIL VIH ILPD GND 1.5 - - 0.2 VDD 1.0 V V μA PD=2.8V Vtemp VSE 1.279 -8.00 1.300 -8.20 1.321 -8.40 V mV/℃ ⊿VtempRL - - 1.0 mV ⊿VtempVDD - - 4.0 mV IL VOL - - 1.0 0.4 μA SYMBOL UNIT V CONDITIONS Ta = 30℃ Ta = -30 to 100℃ difference of IOUT : 0μA / 2μA VDD=2.4～5.5V VOS =5.0V IOS = 1.0mA ● TEMPERATURE ACCURACY ( unless otherwise specified, VDD = 2.8V ) PARAMETER Thermostat Sensing Temperature Accuracy Sensing Temperature Hysteresis Analog Output Vtemp Temperature Accuracy www.rohm.com © 2009 ROHM Co., Ltd. All rights reserved. MIN. LIMIT TYP. MAX. Tacc - ±1.0 ±2.5 ℃ Thys 7.5 10.0 12.5 ℃ Ttemp - ±1.0 ±2.5 ℃ SYMBOL 2/9 UNIT CONDITIONS VDD = 2.8V Ta = -30 to 100℃ 2009.08 - Rev.C Technical Note BDJ□□□1HFV Series ● Block Diagram Vtemp 1 GND 2 IRef 5 VDD 4 OS VRef TEMP SENSOR PD 3 PD ● PIN DESCRIPTION PIN NO. PIN NAME 1 Vtemp 2 GND 3 PD 4 OS 5 VDD FUNCTION Output voltage in inverse proportion to the temperature ( TYP. -8.20mV/℃ ) GROUND PD control H : Normal function mode L : Power Down mode COMMENT Set the OPEN state or connect high impedance input node.(over 10MΩ） "H" Thermostat and Analog output operation. "L" Power Down state. Open Drain Active H. Use the pull-up resistor more than 10kΩ. Digital thermostat output POWER SUPPLY ● EQUIVALENT CIRCUIT PD OS VDD OS PD GND Use the pull-up resistor more than 10kΩ. GND Vtemp VDD Vtemp GND www.rohm.com © 2009 ROHM Co., Ltd. All rights reserved. 3/9 2009.08 - Rev.C Technical Note BDJ□□□1HFV Series ● PACKAGE OUTLINES ( HVSOF5 ) MARKING Lot No. HVSOF5(UNIT:mm) ● Block Diagram Please adjust Capacitor by the noise condition of the Vtemp set. VDD IRef 1 0.1μF GND 5 VRef 2 3 www.rohm.com by the noise condition of the set. OS PD © 2009 ROHM Co., Ltd. All rights reserved. Please adjust bypass Capacitor + - TEMP SENSOR PD 1μF 4 4/9 Please pull-up over 10kΩfor OS output terminal. 2009.08 - Rev.C Technical Note BDJ□□□1HFV Series ●Reference Data 2.0 15 Ta=30°C Ta=30°C 1.5 Vtemp [V] IDD [μA] 10 PD="H" 1.0 5 0.5 PD="L" 0 0.0 0 1 2 3 4 5 6 0 7 1 2 VDD [V] Fig1. Supply Current(IDD) vs. Supply Voltage 3 4 VDD [V] 5 6 7 Fig2. Vtemp Voltage vs. Supply Voltage 2.0 2 VDD=2.8V 0 1.5 ⊿Vtemp [mV] Vtemp[V] -2 1.0 0.5 -4 -6 -8 VDD=2.8V, Ta=30°C -10 0.0 -40 -20 0 20 40 Temp[℃] 60 80 100 -12 0 1 2 3 4 5 Iout [uA] Fig3. Vtemp Voltage vs. Temperature Fig4. Vtemp Voltage vs. Output Current 0.8 VDD=2.8V, Ta=25°C VOL[V] 0.6 0.4 0.2 0 0 1 2 3 IOS [mA] 4 5 Fig5. OS Output Voltage vs. Load Current www.rohm.com © 2009 ROHM Co., Ltd. All rights reserved. 5/9 2009.08 - Rev.C Technical Note BDJ□□□1HFV Series ●Function Diagram（ex. 80℃ detect Active“H”type BDJ0801HFV） Temperature sensor internal IC sense temperature, Vtemp terminal output voltage convert temperature. Vtemp value is 1.300[V] at Ta = 30[℃]. The value of Vtemp voltage reduce reversely proportional temperature at rate of –8.2mV/℃. OS Output Voltage( VOS ) [V] Analog Temp. Sensor Output [V] 3.0 2.5 2.0 Vtemp@30℃ ( 1.300V ) 1.5 1.0 Temperature Sensitivity ( -8.20mV/℃ typ.) 0.5 Vos Detect point Temperature Hysteresis ( 10℃ typ.) 0 -50 -30 -10 10 30 50 70 90 110 130 Temperature [℃] If the temperature over detect temperature, internal comparator operate OS output “L” to “H”.(ex.active “H” Type) In case of OS return to “L”,the temperature 10℃ lower than detect temperature. www.rohm.com © 2009 ROHM Co., Ltd. All rights reserved. 6/9 2009.08 - Rev.C Technical Note BDJ□□□1HFV Series ●Operation Sequence （ex.80℃ detect Active“H”type BDJ0801HFV） VDD H level 1.5V L level 0.2V PD 7.5µA IDD 7.5µA 0.3µA 0.3µA 0.3µA 1.300V@Ta=30℃ Vtemp OS Ref Voltage Hi Z 70°C 80°C Hi Z Hi Z Hi Z（pull-up） Hi Z Hi Z Hi Z time ｔOS_L ｔOS_H BDJ0801HFV operate start after PD“H”Input. Please read OS terminal signal below wait time after PD ”H” Input. Ta Symbol Wait time Under detect Temp. ｔOS_L 200µs Over detect Temp. ｔOS_H 1000µs www.rohm.com © 2009 ROHM Co., Ltd. All rights reserved. 7/9 2009.08 - Rev.C Technical Note BDJ□□□1HFV Series ●Notes for use 1) Absolute Maximum Ratings An excess in the absolute maximum ratings, such as supply voltage, temperature range of operating conditions, etc., can break down devices, thus making impossible to identify breaking mode such as a short circuit or an open circuit. If any special mode exceeding the absolute maximum ratings is assumed, consideration should be given to take physical safety measures including the use of fuses, etc. 2) GND voltage Make setting of the potential of the GND terminal so that it will be maintained at the minimum in any operating state. 3) Pin short and mistake fitting When mounting the IC on the PCB, pay attention to the orientation of the IC. If there is a placement mistake, the IC may be burned up. 4) Operation in strong electric field Be noted that using ICs in the strong electric field can malfunction them. 5) Mutual impedance Use short and wide wiring tracks for the power supply and ground to keep the mutual impedance as small as possible. Use a capacitor to keep ripple to a minimum. www.rohm.com © 2009 ROHM Co., Ltd. All rights reserved. 8/9 2009.08 - Rev.C Technical Note BDJ□□□1HFV Series ●Ordering part number B D J 0 9 0 1 H Detect Temp. Series Name 090: 90℃ 070: 70℃ 085: 85℃ 065: 65℃ 080: 80℃ 060: 60℃ 075: 75℃ 055: 55℃ F V Package : HVSOF5 T R TR=Reel-wound embossed taping Output Format 0 : active L 1 : active H HVSOF5 <Tape and Reel information> 4 Embossed carrier tape (0.3) Quantity 3000pcs (0.91) 4 0.2MAX (0.05) 5 Tape 5 (0.41) 1.6±0.05 1.0±0.05 (0.8) Direction of feed TR The direction is the 1pin of product is at the upper right when you hold ( reel on the left hand and you pull out the tape on the right hand ) 3 2 1 1 2 3 1pin 0.13±0.05 S +0.03 0.02 –0.02 0.6MAX 1.2±0.05 (MAX 1.28 include BURR) 1.6±0.05 0.1 S 0.5 0.22±0.05 0.08 Direction of feed M (Unit : mm) www.rohm.com © 2009 ROHM Co., Ltd. All rights reserved. Reel 9/9 ∗ Order quantity needs to be multiple of the minimum quantity. 2009.08 - Rev.C Notice Notes No copying or reproduction of this document, in part or in whole, is permitted without the consent of ROHM Co.,Ltd. The content specified herein is subject to change for improvement without notice. The content specified herein is for the purpose of introducing ROHM's products (hereinafter "Products"). If you wish to use any such Product, please be sure to refer to the specifications, which can be obtained from ROHM upon request. Examples of application circuits, circuit constants and any other information contained herein illustrate the standard usage and operations of the Products. The peripheral conditions must be taken into account when designing circuits for mass production. Great care was taken in ensuring the accuracy of the information specified in this document. However, should you incur any damage arising from any inaccuracy or misprint of such information, ROHM shall bear no responsibility for such damage. The technical information specified herein is intended only to show the typical functions of and examples of application circuits for the Products. ROHM does not grant you, explicitly or implicitly, any license to use or exercise intellectual property or other rights held by ROHM and other parties. ROHM shall bear no responsibility whatsoever for any dispute arising from the use of such technical information. The Products specified in this document are intended to be used with general-use electronic equipment or devices (such as audio visual equipment, office-automation equipment, communication devices, electronic appliances and amusement devices). The Products specified in this document are not designed to be radiation tolerant. While ROHM always makes efforts to enhance the quality and reliability of its Products, a Product may fail or malfunction for a variety of reasons. Please be sure to implement in your equipment using the Products safety measures to guard against the possibility of physical injury, fire or any other damage caused in the event of the failure of any Product, such as derating, redundancy, fire control and fail-safe designs. ROHM shall bear no responsibility whatsoever for your use of any Product outside of the prescribed scope or not in accordance with the instruction manual. The Products are not designed or manufactured to be used with any equipment, device or system which requires an extremely high level of reliability the failure or malfunction of which may result in a direct threat to human life or create a risk of human injury (such as a medical instrument, transportation equipment, aerospace machinery, nuclear-reactor controller, fuel-controller or other safety device). ROHM shall bear no responsibility in any way for use of any of the Products for the above special purposes. If a Product is intended to be used for any such special purpose, please contact a ROHM sales representative before purchasing. If you intend to export or ship overseas any Product or technology specified herein that may be controlled under the Foreign Exchange and the Foreign Trade Law, you will be required to obtain a license or permit under the Law. Thank you for your accessing to ROHM product informations. More detail product informations and catalogs are available, please contact us. ROHM Customer Support System http://www.rohm.com/contact/ www.rohm.com © 2009 ROHM Co., Ltd. All rights reserved. R0039A