Datasheet DC Brushless Motor Drivers for Cooling Fans Two-phase Full-wave DC Brushless Fan Motor Drivers BA6901F ●General description BA6901F is two-phase half-wave fan motor driver. They incorporate lock protection, automatic restart circuit and FG/AL output. Some of them have variable speed control function. ●Package SOP-16 W (Typ.) x D (Typ.) x H (Max.) 10.00mm x 6.20mm x 1.71mm ●Features Current Limit circuit PWM control (PWM pulse signal input) Incorporates lock protection and automatic restart circuit Lock alarm signal(AL) output Rotation speed pulse signal (FG) output SOP16 ●Application For desktop PC, server, general consumer equipment, communication equipment and industrial equipment. ●Absolute maximum ratings Parameter Supply voltage Power dissipation Operating temperature Storage temperature Output current FG signal output current FG signal output voltage AL signal output current AL signal output voltage Junction temperature * Symbol Vcc Pd Topr Tstg Iomax Ifg Vfg Ial Val Tjmax Limit 36 625* -40〜+100 -55〜+150 70 15 36 15 36 150 Unit V mW ℃ ℃ mA mA V mA V ℃ Reduce by 5.0mW/°C over Ta=25°C. (On 70.0mm×70.0mm×1.6mm glass epoxy board) ●Recommended operating conditions Parameter Operating supply voltage range Hall input voltage range ○Product structure：Silicon monolithic integrated circuit . www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111・14・001 Symbol Vcc VH Limit Unit 3.5〜28.0 0〜Vcc-2.2 V V ○This product is not designed protection against radioactive rays 1/17 TSZ02201-0H1H0B100500-1-2 18.DEC.2012 Rev.002 Datasheet BA6901F ●Pin description ●Pin configuration P/No. T/Name 1 CR 2 FG 3 AL 4 ALB 5 PWM 6 LD 7 CNF 8 9 10 11 12 13 14 15 GND H+ HCS CL A1 A2 Vcc 16 TOUT (TOP VIEW) CR 1 16 TOUT FG 2 15 Vcc AL 3 14 A2 ALB 4 13 A1 PWM 5 12 CL LD 6 11 CS CNF 7 10 H– GND 8 9 H+ Fig. 1 Pin configuration Function Charging and discharging pulse circuit capacitor and resistor connecting terminal Rotating speed pulse signal output terminal Lock alarm signal output terminal Lock alarm signal terminal (inversion signal of AL) PWM input terminal (H or OPEN:Output ON, L:Output OFF) Lock detection and automatic restart capacitor connecting terminal Phase compensating capacitor connecting terminal GND terminal Hall input terminal + Hall input terminal Current detecting input terminal Current limiting input terminal Output terminal 1 Output terminal 2 Power terminal Charging and discharging pulse output terminal ●Block diagram TOUT CR + 1 16 - FG Vcc 2 15 REG 3 ALB 4 LOCK DETECTION & AUTOMATIC RESTART LOGIC AL A2 A2 14 A1 13 A1 PWM CL 5 12 PWM LD 6 + CS 11 + - CNF H- 7 10 GND - + + - 8 H+ 9 Fig.2 Block diagram www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111・15・001 2/17 TSZ02201-0H1H0B100500-1-2 18.DEC.2012 Rev.002 Datasheet BA6901F ●I/O truth table Hall input Driver output H+ H- PWM A1 A2 FG H L H, OPEN H(Output Tr ON) L(Output Tr OFF) H (Output Tr OFF) L H H, OPEN L(Output Tr OFF) H(Output Tr ON) L(Output Tr ON) H L L L(Output Tr OFF) L(Output Tr OFF) H(Output Tr OFF) L H L L(Output Tr OFF) L(Output Tr OFF) L(Output Tr ON) H L H, OPEN H(Output Tr ON) L(Output Tr OFF) H(Output Tr OFF) H; High, L; Low, Hi-Z; High impedance FG output is open-drain type. Motor state Rotating Locking AL L Hi-Z L; Low, Hi-Z; High impedance AL output is open-drain type. www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111・15・001 3/17 TSZ02201-0H1H0B100500-1-2 18.DEC.2012 Rev.002 Datasheet BA6901F ●Electrical characteristics(Unless otherwise specified Ta=25°C, Vcc=12V) Icc Vhys Min. 3.0 ±4 Limit Typ. 7.0 ±10 Max. 12.0 ±20 Ildc 2.0 5.0 Ildd 0.2 rCD Parameter Symbol Circuit current Hall input hysteresis Charge current of capacitor for lock detection Discharge current of capacitor for lock detection Charge-discharge current ratio of capacitor for lock detection Clamp voltage of capacitor for lock detection Comparison voltage of capacitor for lock detection Output H voltage FG output L voltage AL output L voltage CL-CS offset voltage Response time for current limit PWM input voltage H PWM input voltage L Charge-discharge pulse comparison voltage Charge-discharge pulse output voltage H Charge-discharge pulse output voltage L www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111・15・001 Unit Conditions mA mV At output OFF 8.0 µA Vld=1.5V 0.5 0.8 µA Vld=1.5V 4 10 16 - Vldcl 1.60 2.40 3.20 V Vldcp 0.25 0.60 0.95 V Voh - 1.5 2.0 V Vfgl Vall Vofscs Tcs Vpwmh Vpwml 75.0 2.0 - 0.10 0.10 92.0 50 - 0.50 0.50 99.5 150 0.8 V V mV Μsec V V Vcrcp 0.26 0.35 0.44 V Vtoh 0.7 1.0 1.3 V ITO=-0.5mA Voltage between output and Vcc Vtol 0.7 1.0 1.3 V ITO=0.5mA 4/17 rCD=Ildc/Illd Io=-10mA Voltage between output and Vcc IFG=5mA IAL,IALB=5mA CL=100mV At output ON At output OFF TSZ02201-0H1H0B100500-1-2 18.DEC.2012 Rev.002 Datasheet BA6901F ●Typical performance curves(Reference data) 10 20 6 Hall input hysteresis, Vhys [mV] 8 Circuit current, Icc [mA] 100℃ 100℃ 25℃ -40℃ 4 2 25℃ 10 -40℃ 0 100℃ -10 25℃ Operating Voltage Range Operating Voltage Range -40℃ 0 -20 0 6 12 18 24 18 Fig.3 Circuit current Fig.4 Hall input hysteresis Clamp/Comparate voltage, VLDCL/VLDCP [V] Charge/Discharge current, ILDC/ILDD [uA] 12 Supply voltage, Vcc [V] 100℃ 25℃ 4.0 -40℃ 2.0 -40℃ 25℃ 0.0 Operating Voltage Range 100℃ -2.0 6 6 Supply voltage, Vcc [V] 6.0 0 0 30 12 18 24 Supply voltage, Vcc [V] 24 30 Operating Voltage Range 4.0 -40℃ 3.0 25℃ 2.0 100℃ 1.0 0.0 6 12 18 Supply voltage, Vcc [V] Fig.5 Charge-discharge current of capacitor for lock detection www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111・15・001 30 5.0 0 30 24 Fig.6 Clamp-comparison voltage of capacitor for lock detection 5/17 TSZ02201-0H1H0B100500-1-2 18.DEC.2012 Rev.002 Datasheet BA6901F ●Typical performance curves(Reference data) 1.0 0.0 0.8 100℃ -2.0 FG low voltage, VFGL[V] Output H voltage, VOH [V] -1.0 25℃ -40℃ -3.0 -4.0 0.6 0.4 100℃ 0.2 25℃ -40℃ 0.0 -5.0 0 20 40 60 80 0 3 Output current, Io [mA] 9 12 15 FG current, IFG[mA] Fig.7 Output H voltage Fig.8 FG Output L voltage 1.0 1.0 Offset voltage, VofsCS [mV] 0.8 AL low voltage, VALL [V] 6 0.6 0.4 100℃ 0.2 25℃ -40℃ 0.8 -40℃ 25℃ 100℃ 0.5 0.3 Operating Voltage Range 0.0 0.0 0 3 6 9 12 0 15 AL current, IAL[mA] 12 18 24 30 Supply voltage, Vcc[V] Fig10 CS-CL offset voltage Fig9 AL Output L voltage www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111・15・001 6 6/17 TSZ02201-0H1H0B100500-1-2 18.DEC.2012 Rev.002 Datasheet BA6901F ●Typical performance curves(Reference data) 2.0 -40℃ Threshold voltage [V] 1.5 25℃ 100℃ 1.0 0.5 Operating Voltage Range 0.0 0 6 12 18 24 30 Supply voltage, Vcc[V] Fig.11 PWM input threshold voltage www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111・15・001 7/17 TSZ02201-0H1H0B100500-1-2 18.DEC.2012 Rev.002 Datasheet BA6901F ●Application circuit example(Constant values are for reference) Incorporates charging and discharging pulse circuit and enables speed control corresponding to ambient temperature with use of thermistor. Take a measure against Vcc voltage rise generated by reverse connection of current and back electromotive force. 5kΩ 〜200kΩ TOUT CR + 1 0.1μF 〜4.7μF FG Vcc 2 15 3 Enables speed pulse input. control Lock Detect Auto Restart ALB by 4 A2 A2 14 A1 13 0.47μF 〜4.7μF CL 5 Phase compensating capacitor when current is limited. 12 PWM 〜5Ω LD 0.001μF 〜0.1μF Current limit setting resistor. A1 PWM Lock detection ON time and lock detection OFF time can be set. Output Tr is equipped externally. Provide a back electromotive force regenerating current route by Zenner diode for clamping. REG AL LOGIC Incorporates power supply clamp circuit and enables application of high voltage. 16 - 6 + CS 11 + - CNF H- 7 10 GND Output current detecting resistor. Pay attention to wattage because large current is present - + + - 8 H+ HALL Set according to the amplitude of hall element output and hall input voltage range. 9 Fig.12 application circuit Substrate design note a) IC power, motor outputs, and motor ground lines are made as fat as possible. b) IC ground (signal ground) line is common with the application ground except motor ground (i.e. hall ground etc.), and arranged near to (–) land. c) The bypass capacitor and/or Zenner diode are arrangement near to Vcc terminal. d) H+ and H– lines are arranged side by side and made from the hall element to IC as shorter as possible, because it is easy for the noise to influence the hall lines. www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111・15・001 8/17 TSZ02201-0H1H0B100500-1-2 18.DEC.2012 Rev.002 Datasheet BA6901F ●Description of operations 1) Lock protection and automatic restart ○CR timer system Charging and discharging time at LD terminal depends on the capacitor equipped externally on LD terminal. Charging and discharging time is determined as follows: C×(VLDCL-VLDCP) TON(charging time) = ILDC C×(VLDCL-VLDCP) TOFF(discharging time)= C ＶLDCL ＶLDCP ＩLDC ＩLDD ： ： ： ： ： ILDD Capacity of capacitor equipped externally on LD terminal LD terminal clamping voltage LD terminal comparator voltage LD terminal charging current LD terminal discharging current Timing chart of LD terminal is shown in Fig.13. H- A1 TOFF LD terminal clamping voltage LD Output Tr OFF TON ON LD terminal comparator voltage HIGH(open collector) AL FG Motor Lock locking detection Lock release Recovers normal operation Fig.13 Lock protection (CR timer system) timing chart 2) PWM terminal The signal input to PWM terminal is below L (0.8V or less), output (A1 and A2) turns off. And when it is above H (2.0V or more), output turns on. PWM terminal is pulled up by resistor (30kΩ:typ.) inside IC. When it is open, the output is in operating mode. H+ PWM A1 A2 FG Fig.14 Timing chart in PWM control www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111・15・001 9/17 TSZ02201-0H1H0B100500-1-2 18.DEC.2012 Rev.002 Datasheet BA6901F 3) Charging and discharging pulse circuit compatible with temperature variable speed control When an external capacitor and resistor are connected to CR terminal, saw wave is generated by charging and discharging of capacitor corresponding to the cycle of hall signal. Saw wave of CR terminal changes with the external capacitor and resistor. Waveform of CR terminal is output to TOUT by buffer amplifier. CR terminal is variable from VCRCP (0.35V:typ., see the electric characteristics) to Vcc. When CR voltage is above Vcc-VTOH (1V:typ., see the electric characteristics), CR terminal signal is not output to TOUT terminal as shown in Fig.15. Hall input Hall input Vcc-VTOH (typ.：Vcc-1V) Vcc-VTOH (typ.：Vcc-1V) VCRCP (typ.：0.35V) CR CR VCRCP (typ.：0.35V) Vcc-VTOH (typ.：Vcc-1V) TOUT VTOL (typ.：1V) TOUT VTOL (typ.：1V) Fig.15 CR terminal and TOUT terminal timing chart www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111・15・001 10/17 TSZ02201-0H1H0B100500-1-2 18.DEC.2012 Rev.002 Datasheet BA6901F 4) Variable speed control application This is an example of the application which makes the fan motor rotating speed variable corresponding to ambient temperature with thermistor by use of charging and discharging pulse circuit and PWM input. TOUT CR 16 + 1 - Vcc FG 15 2 REG 3 LOGIC AL Lock Detect Auto Restart ALB 4 A2 A2 14 A1 13 A1 CL PWM + VTH - Thermistor 5 - LD 6 12 PWM + CS 11 + - CNF H- 7 10 GND 8 - + + - H+ HALL 9 Fig. 16 Example of temperature variable speed application VTH TOUT PWM A1 A2 Fig. 17 Temperature variable speed timing chart When the temperature becomes the lower and the thermistor terminal voltage the higher, PWM pulse becomes the shorter and speed is reduced as shown in Fig. 17. www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111・15・001 11/17 TSZ02201-0H1H0B100500-1-2 18.DEC.2012 Rev.002 Datasheet BA6901F 5) Current limiting circuit ＜BA6901F＞ Output current limitation can be set by the voltage (VCL) input to CL terminal. Connect a resistor (RNF) for detecting output current between the emitter of external output transistor and GND, and input the voltage generated by resistor to CS terminal, thereby detecting the output current. The output current is limited so that CL terminal and CS terminal has the same potential. There is an offset between CL terminal and CS terminal. Current limiting value can be calculated by the formula below: Current limiting value ＝ VCL−VofsCS RNF VofsCS = CL-CS offset When limiting the output current, capacitor for phase compensation must be connected between CNF terminal and Vcc terminal. When the output current is not to be limited, fix CL terminal voltage to High level (Vcc) and CS terminal to Low level (GND). CNF Vcc CNF Vcc A1 A1 A2 A2 CS CS CL Current limiting CL (a) When current limiting is applied (b) When current limiting is not applied Fig.18 External circuit of output www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111・15・001 12/17 TSZ02201-0H1H0B100500-1-2 18.DEC.2012 Rev.002 Datasheet BA6901F ●Power dissipation Power dissipation (total loss) indicates the power that can be consumed by IC at Ta = 25ºC (normal temperature). IC is heated when it consumes power, and the temperature of IC chip becomes higher than ambient temperature. The temperature that can be accepted by IC chip depends on circuit configuration, manufacturing process, etc, and consumable power is limited. Power dissipation is determined by the temperature allowed in IC chip (maximum junction temperature) and thermal resistance of package (heat dissipation capability). The maximum junction temperature is in general equal to the maximum value in the storage temperature range. Heat generated by consumed power of IC is radiated from the mold resin or lead frame of package. The parameter which indicates this heat dissipation capability (hardness of heat release) is called heat resistance, represented by the symbol θ ja [℃/W]. The temperature of IC inside the package can be estimated by this heat resistance. Fig.19 shows the model of heat resistance of the package. Heat resistance θja, ambient temperature Ta, junction temperature Tj, and power consumption P can be calculated by the equation below: θja = (Tj – Ta) / P [°C/W] Thermal derating curve indicates power that can be consumed by IC with reference to ambient temperature. Power that can be consumed by IC begins to attenuate at certain ambient temperature. This gradient is determined by thermal resistance θja. Thermal resistance θja depends on chip size, power consumption, package ambient temperature, packaging condition, wind velocity, etc., even when the same package is used. Thermal derating curve indicates a reference value measured at a specified condition. Fig.20 shows a thermal derating curve (Value when mounting FR4 glass epoxy board 70 [mm] x 70 [mm] x 1.6 [mm] (copper foil area below 3 [%])) Pd(mW) 800 700 625 600 560 θja = (Tj – Ta) / P [°C/W] BA6901F 500 Ambient temperature Ta[°C] Package surface temperature Tc[°C] 400 300 200 100 0 Chip surface temperature Tj[°C] Power consumption P[W] 25 50 75 95 100 125 150 Ta(℃) *Reduce by 5.0mW/°C over 25°C (On 70.0mm x 70.0mm x 1.6mm glass epoxy board) Fig.19 Thermal resistance Fig.20 Thermal de-rating curve ●I/O equivalence circuit(Resistance values are typical) 1) Hall input terminal 2) Current limiting input terminal Output current detecting terminal 3) Charge-discharge pulse output terminal Vcc Vcc Vcc 30Ω H+ H- 1kΩ 1kΩ TOUT 1kΩ CS 30Ω 1kΩ CL 4) PWM input terminal 5) Output terminal Vcc Vcc 1kΩ 6) Signal output terminal FG、AL、ALB 30kΩ 1kΩ PWM A1, A2 100kΩ 15kΩ GND www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111・15・001 13/17 TSZ02201-0H1H0B100500-1-2 18.DEC.2012 Rev.002 Datasheet BA6901F ●Safety measure 1) Reverse connection protection diode Reverse connection of power results in IC destruction as shown in Fig 21. When reverse connection is possible, reverse connection protection diode must be added between power supply and Vcc. Reverse power connection In normal energization Vcc After reverse connection destruction prevention Vcc Vcc Circuit block Circuit block Each pin GND Internal circuit impedance high Æ amperage small Circuit block Each pin GND Large current flows Æ Thermal destruction Each pin GND No destruction Fig.21 Current flow when power is connected reversely 2) About measures of voltage rise by back electromotive force The voltage of output terminal rises by back electromotive force. The diode D1 of Fig.22 is necessary to divide a power supply line of motor with small signal line, so that the voltage of the output does not affect a power supply line. D1 IC Fig.22 Separation of a power supply line 3) FG/AL output Vcc FG /AL Pull-up resistor Protection resistor R1 Connector of board Fig.23 Protection of FG and AL terminal FG and AL output is an open collector and requires pull-up resistor. The IC can be protected by adding resistor R1. An excess of absolute maximum rating, when FG or AL output terminal is directly connected to power supply, could damage the IC. www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111・15・001 14/17 TSZ02201-0H1H0B100500-1-2 18.DEC.2012 Rev.002 Datasheet BA6901F 4) Problem of GND line PWM switching Do not perform PWM switching of GND line because GND terminal potential cannot be kept to a minimum. Vcc Motor Driver GND Controller PWM input Prohibite Fig.24 GND Line PWM switching prohibited www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111・15・001 15/17 TSZ02201-0H1H0B100500-1-2 18.DEC.2012 Rev.002 Datasheet BA6901F ●Operational Notes 1) Absolute maximum ratings An excess in the absolute maximum rations, such as supply voltage, temperature range of operating conditions, etc., can break down the devices, thus making impossible to identify breaking mode, such as a short circuit or an open circuit. If any over rated values will expect to exceed the absolute maximum ratings, consider adding circuit protection devices, such as fuses. 2) Connecting the power supply connector backward Connecting of the power supply in reverse polarity can damage IC. Take precautions when connecting the power supply lines. An external direction diode can be added. 3) Power supply line Back electromotive force causes regenerated current to power supply line, therefore take a measure such as placing a capacitor between power supply and GND for routing regenerated current. And fully ensure that the capacitor characteristics have no problem before determine a capacitor value. (when applying electrolytic capacitors, capacitance characteristic values are reduced at low temperatures) 4) GND potential The potential of GND pin must be minimum potential in all operating conditions. Also ensure that all terminals except GND terminal do not fall below GND voltage including transient characteristics. However, it is possible that the motor output terminal may deflect below GND because of influence by back electromotive force of motor. Malfunction may possibly occur depending on use condition, environment, and property of individual motor. Please make fully confirmation that no problem is found on operation of IC. 5) Thermal design Use a thermal design that allows for a sufficient margin in light of the power dissipation(Pd) in actual operating conditions. 6) Inter-pin shorts and mounting errors Use caution when positioning the IC for mounting on printed circuit boards. The IC may be damaged if there is any connection error or if pins are shorted together. 7) Actions in strong electromagnetic field Use caution when using the IC in the presence of a strong electromagnetic field as doing so may cause the IC to malfunction. 8) ASO When using the IC, set the output transistor so that it does not exceed absolute maximum rations or ASO. 9) Thermal shut down circuit The IC incorporates a built-in thermal shutdown circuit (TSD circuit). Operation temperature is 175℃(typ.) and has a hysteresis width of 25℃(typ.). When IC chip temperature rises and TSD circuit works, the output terminal becomes an open state. TSD circuit is designed only to shut the IC off to prevent thermal runaway. It is not designed to protect the IC or guarantee its operation. Do not continue to use the IC after operation this circuit or use the IC in an environment where the operation of this circuit is assumed. 10) Testing on application boards When testing the IC on an application board, connecting a capacitor to a pin with low impedance subjects the IC to stress. Always discharge capacitors after each process or step. Always turn the IC’s power supply off before connecting it to or removing it from a jig or fixture during the inspection process. Ground the IC during assembly steps as an antistatic measure. Use similar precaution when transporting or storing the IC. 11) GND wiring pattern When using both small signal and large current GND patterns, it is recommended to isolate the two ground patterns, placing a single ground point at the ground potential of application so that the pattern wiring resistance and voltage variations caused by large currents do not cause variations in the small signal ground voltage. Be careful not to change the GND wiring pattern of any external components, either. 12) Capacitor between output and GND When a large capacitor is connected between output and GND, if Vcc is shorted with 0V or GND for some cause, it is possible that the current charged in the capacitor may flow into the output resulting in destruction. Keep the capacitor between output and GND below 100uF. 13) IC terminal input When Vcc voltage is not applied to IC, do not apply voltage to each input terminal. When voltage above Vcc or below GND is applied to the input terminal, parasitic element is actuated due to the structure of IC. Operation of parasitic element causes mutual interference between circuits, resulting in malfunction as well as destruction in the last. Do not use in a manner where parasitic element is actuated. 14) In use We are sure that the example of application circuit is preferable, but please check the character further more in application to a part which requires high precision. In using the unit with external circuit constant changed, consider the variation of externally equipped parts and our IC including not only static character but also transient character and allow sufficient margin in determining. www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111・15・001 16/17 TSZ02201-0H1H0B100500-1-2 18.DEC.2012 Rev.002 Datasheet BA6901F ●Physical dimension tape and reel information SOP16 <Tape and Reel information> 10 ± 0.2 (MAX 10.35 include BURR) 9 Tape Embossed carrier tape Quantity 2500pcs Direction of feed E2 The direction is the 1pin of product is at the upper left when you hold ( reel on the left hand and you pull out the tape on the right hand ) 0.3MIN 4.4±0.2 6.2±0.3 16 1 8 0.11 1.5±0.1 0.15 ± 0.1 1.27 0.4 ± 0.1 0.1 1pin (Unit : mm) Reel Direction of feed ∗ Order quantity needs to be multiple of the minimum quantity. ●Marking diagram SOP16(TOP VIEW) Part Number Marking B A 6 9 0 1 F LOT Number 1PIN MARK www.rohm.com © 2012 ROHM Co., Ltd. All rights reserved. TSZ22111・15・001 17/17 TSZ02201-0H1H0B100500-1-2 18.DEC.2012 Rev.002 Datasheet Notice Precaution on using ROHM Products 1. Our Products are designed and manufactured for application in ordinary electronic equipments (such as AV equipment, OA equipment, telecommunication equipment, home electronic appliances, amusement equipment, etc.). If you (Note 1) , transport intend to use our Products in devices requiring extremely high reliability (such as medical equipment equipment, traffic equipment, aircraft/spacecraft, nuclear power controllers, fuel controllers, car equipment including car accessories, safety devices, etc.) and whose malfunction or failure may cause loss of human life, bodily injury or serious damage to property (“Specific Applications”), please consult with the ROHM sales representative in advance. Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of any ROHM’s Products for Specific Applications. (Note1) Medical Equipment Classification of the Specific Applications JAPAN USA EU CHINA CLASSⅢ CLASSⅡb CLASSⅢ CLASSⅢ CLASSⅣ CLASSⅢ 2. ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate safety measures including but not limited to fail-safe design against the physical injury, damage to any property, which a failure or malfunction of our Products may cause. The following are examples of safety measures: [a] Installation of protection circuits or other protective devices to improve system safety [b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure 3. Our Products are designed and manufactured for use under standard conditions and not under any special or extraordinary environments or conditions, as exemplified below. Accordingly, ROHM shall not be in any way responsible or liable for any damages, expenses or losses arising from the use of any ROHM’s Products under any special or extraordinary environments or conditions. If you intend to use our Products under any special or extraordinary environments or conditions (as exemplified below), your independent verification and confirmation of product performance, reliability, etc, prior to use, must be necessary: [a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents [b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust [c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2 [d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves [e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items [f] Sealing or coating our Products with resin or other coating materials [g] Use of our Products without cleaning residue of flux (even if you use no-clean type fluxes, cleaning residue of flux is recommended); or Washing our Products by using water or water-soluble cleaning agents for cleaning residue after soldering [h] Use of the Products in places subject to dew condensation 4. The Products are not subject to radiation-proof design. 5. Please verify and confirm characteristics of the final or mounted products in using the Products. 6. In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse. is applied, confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect product performance and reliability. 7. De-rate Power Dissipation (Pd) depending on Ambient temperature (Ta). When used in sealed area, confirm the actual ambient temperature. 8. Confirm that operation temperature is within the specified range described in the product specification. 9. ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined in this document. Precaution for Mounting / Circuit board design 1. When a highly active halogenous (chlorine, bromine, etc.) flux is used, the residue of flux may negatively affect product performance and reliability. 2. In principle, the reflow soldering method must be used; if flow soldering method is preferred, please consult with the ROHM representative in advance. For details, please refer to ROHM Mounting specification Notice - GE © 2014 ROHM Co., Ltd. All rights reserved. Rev.002 Datasheet Precautions Regarding Application Examples and External Circuits 1. If change is made to the constant of an external circuit, please allow a sufficient margin considering variations of the characteristics of the Products and external components, including transient characteristics, as well as static characteristics. 2. You agree that application notes, reference designs, and associated data and information contained in this document are presented only as guidance for Products use. Therefore, in case you use such information, you are solely responsible for it and you must exercise your own independent verification and judgment in the use of such information contained in this document. ROHM shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of such information. Precaution for Electrostatic This Product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. Please take proper caution in your manufacturing process and storage so that voltage exceeding the Products maximum rating will not be applied to Products. Please take special care under dry condition (e.g. Grounding of human body / equipment / solder iron, isolation from charged objects, setting of Ionizer, friction prevention and temperature / humidity control). Precaution for Storage / Transportation 1. Product performance and soldered connections may deteriorate if the Products are stored in the places where: [a] the Products are exposed to sea winds or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2 [b] the temperature or humidity exceeds those recommended by ROHM [c] the Products are exposed to direct sunshine or condensation [d] the Products are exposed to high Electrostatic 2. Even under ROHM recommended storage condition, solderability of products out of recommended storage time period may be degraded. It is strongly recommended to confirm solderability before using Products of which storage time is exceeding the recommended storage time period. 3. Store / transport cartons in the correct direction, which is indicated on a carton with a symbol. Otherwise bent leads may occur due to excessive stress applied when dropping of a carton. 4. Use Products within the specified time after opening a humidity barrier bag. Baking is required before using Products of which storage time is exceeding the recommended storage time period. Precaution for Product Label QR code printed on ROHM Products label is for ROHM’s internal use only. Precaution for Disposition When disposing Products please dispose them properly using an authorized industry waste company. Precaution for Foreign Exchange and Foreign Trade act Since our Products might fall under controlled goods prescribed by the applicable foreign exchange and foreign trade act, please consult with ROHM representative in case of export. Precaution Regarding Intellectual Property Rights 1. All information and data including but not limited to application example contained in this document is for reference only. ROHM does not warrant that foregoing information or data will not infringe any intellectual property rights or any other rights of any third party regarding such information or data. ROHM shall not be in any way responsible or liable for infringement of any intellectual property rights or other damages arising from use of such information or data.: 2. No license, expressly or implied, is granted hereby under any intellectual property rights or other rights of ROHM or any third parties with respect to the information contained in this document. Other Precaution 1. This document may not be reprinted or reproduced, in whole or in part, without prior written consent of ROHM. 2. The Products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written consent of ROHM. 3. In no event shall you use in any way whatsoever the Products and the related technical information contained in the Products or this document for any military purposes, including but not limited to, the development of mass-destruction weapons. 4. The proper names of companies or products described in this document are trademarks or registered trademarks of ROHM, its affiliated companies or third parties. Notice - GE © 2014 ROHM Co., Ltd. All rights reserved. Rev.002 Datasheet General Precaution 1. Before you use our Pro ducts, you are requested to care fully read this document and fully understand its contents. ROHM shall n ot be in an y way responsible or liabl e for fa ilure, malfunction or acci dent arising from the use of a ny ROHM’s Products against warning, caution or note contained in this document. 2. All information contained in this docume nt is current as of the issuing date and subj ect to change without any prior notice. Before purchasing or using ROHM’s Products, please confirm the la test information with a ROHM sale s representative. 3. The information contained in this doc ument is provi ded on an “as is” basis and ROHM does not warrant that all information contained in this document is accurate an d/or error-free. ROHM shall not be in an y way responsible or liable for an y damages, expenses or losses incurred b y you or third parties resulting from inaccur acy or errors of or concerning such information. Notice – WE © 2014 ROHM Co., Ltd. All rights reserved. Rev.001 Datasheet BA6901F - Web Page Buy Distribution Inventory Part Number Package Unit Quantity Minimum Package Quantity Packing Type Constitution Materials List RoHS BA6901F SOP16 2500 2500 Taping inquiry Yes