Click on Series name for product info on aimtec.com Series AM10EW-NZ 10 Watt | DC-DC Converter FEATURES: • Efficiency up to 86% • Ultra Wide 4:1 input range • Continuous Short Circuit Protection • Operating temperature -40oC to + 85oC Models Single output Model AM10EW-11005S-NZ AM10EW-11012S-NZ AM10EW-11015S-NZ AM10EW-11024S-NZ Input Voltage (V) Input Specifications Parameters Voltage range Filter Input Surge Voltage (1sec max.) Start-up Voltage Isolation Specifications Parameters Tested I/O voltage Resistance Capacitance Output Specifications Parameters Voltage accuracy Short Circuit protection Short Circuit restart Transient Recovery Time Transient Deviation Response Line voltage regulation Load voltage regulation Over Voltage Protection Temperature coefficient Ripple & Noise www.aimtec.com F 051e R12.B 40~160 40~160 40~160 40~160 Output Voltage (V) Output Current max (mA) 5 12 15 24 2000 833 667 416 Nominal Typical 110 Conditions 1 min • Low ripple and noise • Over Voltage Protection ● Input / Output Isolation 1500VDC 40~160 π (Pi) Network Typical Capacitive load max (μF) 2200 220 100 47 25% Load Step Change Full Load (HL-LL) 5-100% load 20Mhz bandwidth Typical ±1 Continuous Auto Recovery 500 ±3 ±0.2 ±0.5 120 ±0.03 100 Tel: +1 514 620 2722 1 of 3 81 85 85 86 Maximum Units 180 40 VDC VDC 170 VDC Rated Units VDC MOhm pF Maximum Units 1000 ±5 ±0.5 ±1 140 µs % % % % Vo %/oC mV p-p 1500 > 1000 1000 Conditions Efficiency (%) ±2 % Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM10EW-NZ 10 Watt | DC-DC Converter General Specifications Parameters Switching frequency Operating temperature Conditions Storage temperature Max case temperature Cooling Humidity Maximum 350 -40 to +85 -55 to +125 Free air convection Non condensing 1.5 mm from case 10 sec. Solder Temp Leads Case material Weight Dimensions (L x MTBF Typical 100% load See derating chart Units KHz o C o C o C 105 95 % o 300 C Aluminum Alloy 22 g Tolerance ±0.5mm 2.00 x 1.00 x 0.46 inches 50.80 x 25.40 x 11.80mm >1 000 000 hrs (MIL-HDBK -217F, Ground Benign, t=+25oC) W x H) NOTE: All specifications in this datasheet are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. Safety Specifications Parameters Agency Approvals Designed to meet IEC 60950 1:2001 Pin Out Specifications Pin Single 1 2 3 4 Vin Vin + +Vout -Vout Dimensions 50.80 (2.00) 20.32 (0.80) 1 Bottom View 25.4 (1.00) 2 20.32 (0.80) 5.08 (0.20) 25.40 (1.00) 3 4 50.8 (2.00) Built-in Stand-offs to ease PCB cleaning 11.80 (0.47) Notes: All dimensions are typical in millimeters (inches). Tolerance ±0.25 (±0.01) DIA 1.00 (0.04) www.aimtec.com F 051e R12.B Tel: +1 514 620 2722 2 of 3 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM10EW-NZ 10 Watt | DC-DC Converter Recommended Circuit Vin+ Vin- Vo+ Aimtec DC/DC Converter C2 10µf Load C1 10 ~ 47µf Vo- Note: Greater noise filtering can be achieved with additional capacitors, however the largest size can not exceed maximum capacitive load specification. Parallel connections are not recommended. Product does not support hot swap / plug and play configurations. Derating Output Power ( % ) Free Air Convection 71ºC 100 80 Safe Operating Area 60 40 20 0 -40 -20 0 20 40 60 80 85 100 Ambient Temperature º C NOTE: 1. Datasheets are updated as needed and as such, specifications are subject to change without notice. Once printed or downloaded, datasheets are no longer controlled by Aimtec; refer to www.aimtec.com for the most current product specifications. 2. Product labels shown, including safety agency certifications on labels, may vary based on the date manufactured. 3. Mechanical drawings and specifications are for reference only. 4. All specifications are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. 5. Aimtec may not have conducted destructive testing or chemical analysis on all internal components and chemicals at the time of publishing this document. CAS numbers and other limited information are considered proprietary and may not be available for release. 6. This product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control systems or other such applications which necessitate specific safety and regulatory standards other the ones listed in this datasheet. 7. Warranty is in accordance with Aimtec’s standard Terms of Sale available at www.aimtec.com. www.aimtec.com F 051e R12.B Tel: +1 514 620 2722 3 of 3 Toll free: + 1 888 9 AIMTEC (924 6832) North America only