SMD 14-Pin Triple TTL Compatible Active Delay Lines DELAY TIME ±5% or ±2 nS† PART NUMBER 5 6 7 8 9 10 11 12 13 14 15 16 17 18 EPA280-5 EPA280-6 EPA280-7 EPA280-8 EPA280-9 EPA28010 EPA280-11 EPA280-12 EPA280-13 EPA280-14 EPA280-15 EPA280-16 EPA280-17 EPA280-18 †Whichever is greater. DELAY TIME ±5% or ±2 nS† 19 20 21 22 23 24 25 30 35 40 45 50 55 60 DELAY TIME ±5% or ±2 nS† PART NUMBER EPA280-19 EPA280-20 EPA280-21 EPA280-22 EPA280-23 EPA280-24 EPA280-25 EPA280-30 EPA280-35 EPA280-40 EPA280-45 EPA280-50 EPA280-55 EPA280-60 65 70 75 80 85 90 95 100 125 150 175 200 225 250 EPA280-65 EPA280-70 EPA280-75 EPA280-80 EPA280-85 EPA280-90 EPA280-95 EPA280-100 EPA280-125 EPA280-150 EPA280-175 EPA280-200 EPA280-225 EPA280-250 Delay Times referenced from input to leading edges at 25°C, 5.0V, with no load. DC Electrical Characteristics Parameter VOH VOL VIK IIH High-Level Output Voltage Low-Level Output Voltage Input Clamp Voltage High-Level Input Current IIL IOS Low-Level Input Current Short Circuit Output Current ICCH ICCL TRO NH NL High-Level Supply Current Low-Level Supply Current Output Rise Time Fanout High-Level Output Fanout Low-Level Output Schematic Test Conditions Min Max Unit VCC = min. VIL = max. I OH = max VCC = min. VIH = min. I OL= max VCC = min. II = II K VCC = max. VIN = 2.7V VCC = max. VIN = 5.25V VCC = max. VIN = 0.5V VCC = max. VOUT = 0. (One output at a time) VCC = max. VIN = OPEN VCC = max. VIN = 0 Td ≤ 500 nS (0.75 to 2.4 Volts) VCC = max. VOH = 2.7V VCC = max. VOL = 0.5V Recommended Operating Conditions VCC VIH VIL IIK IOH IOL PW* d* TA PART NUMBER Supply Voltage High-Level Input Voltage Low-Level Input Voltage Input Clamp Current High-Level Output Current Low-Level Output Current Pulse Width of Total Delay Duty Cycle Operating Free-Air Temperature 2.7 -40 0.5 -1.2V 50 1.0 -2 -100 V V V µA mA mA mA 14 10 3 8 115 mA 115 mA 4 nS 20 TTL LOAD 10 TTL LOAD 5 7 GROUND Package Dimensions Min Max Unit 4.75 2.0 5.25 V V V mA mA mA % % °C 0.8 -18 -1.0 20 40 0 40 +70 .420 Max. PCA EPA280-5 Date Code .280 Max. .780 Max. .01 Typ. .200 Max. Input Pulse Test Conditions @ 25° C VCC 12 1 *These two values are inter-dependent. EIN PW TRI PRR VCC Pulse Input Voltage Pulse Width % of Total Delay Pulse Rise Time (0.75 - 2.4 Volts) Pulse Repetition Rate @ Td ≤ 200 nS Pulse Repetition Rate @ Td > 200 nS Supply Voltage Unit 3.2 110 2.0 1.0 100 5.0 .02 .200 .300 Volts % nS MHz KHz Volts QAF-CSO1 Rev. B 8/25/94 DSA280 Rev. A 2/5/96 Unless Otherwise Noted Dimensions in Inches Tolerances: Fractional = ± 1/32 12 .XX = ± .030 .XXX = ± .010 .050 ELECTRONICS INC. 16799 SCHOENBORN ST. NORTH HILLS, CA 91343 TEL: (818) 892-0761 FAX: (818) 894-5791