NSC CLC532AJP High speed 2:1 analog multiplexer Datasheet

CLC532
High Speed 2:1 Analog Multiplexer
General Description
n Adjustable bandwidth–190MHz(max)
The CLC532 is a high speed 2:1 multiplexer with active input
and output stages. The CLC532 innovative design employs
a closed loop design which dramatically improves accuracy.
This monolithic device is constructed using an advanced
high performance bipolar process.
The CLC532 has been specifically designed to provide settling times of 17ns to 0.01%. Fast settling time, coupled with
the adjustable bandwidth, and channel-to-channel isolation
is better than 80dB @10MHz. Low distortion (−80dBc) makes
the CLC532 an ideal choice for infrared and CCD imaging
systems and spurious signal levels make the CLC532 a very
suitable choice for both I/Q processors and receivers.
The CLC532 is offered in two industrial versions,
CLC532AJP\AJE, specified from −40˚C to +85˚C and packaged in 14-pin plastic DIP14-pin and SOIC packages.
Enhanced Solutions (Military/Aerospace)
SMD Number: 5962-92035
Applications
n
n
n
n
n
Infrared system multiplexing
CCD sensor signals
Radar I/Q switching
High definition video HDTV
Test and calibration
Settling Time vs. RL
*Space level versions also available.
*For more information, visit http://www.national.com/mil
Features
n
n
n
n
17ns 12-bit settling time to .01%
Low noise – 32µVrms
High isolation – 80dB @ 10MHz
Low distortion – 80dBc @ 5MHz
DS012716-24
Typical Application
Connection Diagram
DS012716-4
DS012716-2
Pinout
DIP & SOIC
Ordering Information
Package
Temperature Range
Industrial
Part Number
Package Marking
NSC Drawing
14-Pin Plastic DIP
−40˚C to +85˚C
CLC532AJP
CLC532AJP
N14E
14-Pin Plastic SOIC
−40˚C to +85˚C
CLC532AJE
CLC532AJE
M14A
© 2001 National Semiconductor Corporation
DS012716
www.national.com
CLC532 High Speed 2:1 Analog Multiplexer
December 2001
CLC532
Absolute Maximum Ratings (Note 1)
Operating Ratings
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
Positive Supply Voltage (+VCC)
Negative Supply Voltage (−VEE)
Differential Voltage between any two
GDN’s
Analog Input Voltage Range
SELECT Input Voltage Range (TTL
Mode)
SELECT Input Voltage Range (ECL
Mode)
CCOMPRange (Note 3)
Thermal Resistance (θJC)
MDIP
SOIC
Thermal Resistance (θJA)
MDIP
SOIC
Positive Supply Voltage (+VCC)
Negative Supply Voltage (−VEE)
Differential Voltage between any two
GND’s
Analog Input Voltage Range
Digital Input Voltage Range
Output Short Circuit Duration (Output
Shorted to GND)
Operating Temperature Range
Storage Temperature Range
Lead Solder Duration (+300˚C)
ESD Rating
−0.5V to +7.0V
+0.5V to −7.0V
200mV
−VEE to +VCC
−VEE to +VCC
Infinite
−40˚C to +85˚C
−65˚C to +150˚C
10 sec
< 500V
+5v
−5.2V or −5.0V
10mV
± 2V
0.0V to +3.0V
−2.0V to 0.0V
5pF to 100pF
55˚C/W
35˚C/W
100˚C/W
105˚C/W
Electrical Characteristics
(+VCC = +5.0V; −VEE = −5.2V; RIN = 50Ω; RL = 500Ω; CCOMP = 10pF; ECL Mode, pin 6 = NC)
Symbol
Parameter
Case Temperature
Conditions
CLC532AJP/AJE
Typ
Max/Min Ratings
(Note 2)
Units
+25˚C
−40˚C
+25˚C
+85˚C
VOUT < 0.1VPP
190
140
140
110
MHz
VOUT = 2VPP
45
35
35
30
MHz
Frequency Domain Response
SSBW
-3dB Bandwidth
LSBW
Gain Flatness
VOUT < 0.1VPP
GFP
Peaking
0.1MHz to 200MHz
0.2
0.7
0.7
0.8
dB
GFR
Rolloff
0.1MHz to 100MHz
1.0
1.8
1.8
2.6
dB
LPD
Linear Phase Deviation
DC to 100MHz
2.0
DG
Differential Gain
CCOMP = 5pF; RL = 150Ω
0.05
deg
%
DP
Differential Phase
CCOMP = 5pF; RL = 150Ω
0.01
deg
CT10
Crosstalk Rejection
2VPP, 10MHz
80
75
75
74
dB
CT20
2VPP, 20MHz
74
69
69
68
dB
CT30
2VPP, 30MHz
68
63
63
62
dB
Time Domain Performance
TRS
Rise and Fall Time
0.5V Step
2.7
3.3
3.3
3.8
ns
2V Step
10
12.5
12.5
14.5
ns
Settling Time
2V Step; from 50% VOUT
± 0.0025%
± 0.01%
± 0.1%
35
17
24
24
27
ns
13
18
18
21
ns
OS
Overshoot
2.0V Step
2
5
5
6
%
SR
Slew Rate
160
130
130
110
V/µs
TRL
TS14
TSP
TSS
ns
Switch Performance
SWT10
SWT90
Channel to Channel Switching
Time (2V Step at Output)
ST
Switching Transient
50% SELECT to 10% VOUT
5
7
7
8
ns
50% SELECT to 90% VOUT
15
20
20
23
ns
30
mV
Distortion And Noise Performance
HD2
2nd Harmonic Distortion
2VPP, 5MHz
80
67
67
67
dBc
HD3
3rd Harmonic Distortion
2VPP, 5MHz
86
68
68
68
dBc
> 1MHz
3.1
Equivalent Input Noise
SNF
www.national.com
Spot Noise Voltage
2
nV/
CLC532
Electrical Characteristics
(Continued)
(+VCC = +5.0V; −VEE = −5.2V; RIN = 50Ω; RL = 500Ω; CCOMP = 10pF; ECL Mode, pin 6 = NC)
Symbol
Parameter
Conditions
Typ
Max/Min Ratings
(Note 2)
Units
Distortion And Noise Performance
INV
Integrated Noise
SNC
Spot Noise Current
1MHz to 100MHz
32
42
42
46
3
µVrms
pA/
Static And DC Performance
VOS
DVIO
Analog Output Offset Voltage
(Note 5)
Temperature Coefficient
VOSM
Analog Output Voltage Matching
IBN
1
6.5
15
90
3.5
5.5
mV
20
µV/˚C
TBD
mV
Analog Input Bias Current
50
250
DIBN
Temperature Coefficient
0.3
2.0
IBNM
Analog Input Bias Current
Matching (Note 5)
TBD
RIN
Analog Input Resistance
200
CIN
Analog Input Capacitance
GA
Gain Accuracy (Note 5)
GAM
Gain Matching
ILIN
120
120
µA
0.8
µA/˚C
µA
90
120
120
kΩ
2
3.0
2.5
2.5
pF
0.998
0.998
0.998
0.998
V/V
Integral Endpoint Non-Linearity
± 2V
± 2V
± 1V (Full Scale)
0.02
0.05
0.03
0.03
%FS
VO
Output Voltage
No Load
± 3.4
2.4
2.8
2.8
V
IO
Output Current
45
20
30
30
mA
RO
Output Resistance
1.5
4.0
2.5
2.5
Ω
−1.1
−1.1
−1.1
V
TBD
DC
V/V
Digital Input Performance
ECL Mode (Pin 6 Floating)
VIH1
Input Voltage Logic HIGH
VIL1
Input Voltage Logic LOW
−1.5
−1.5
−1.5
V
IIH1
Input Current Logic HIGH
14
50
30
30
µA
Input Current Logic LOW
50
270
110
110
µA
V
IIL1
TTL Mode (pin 6 = +5V)
VIH2
Input Voltage Logic HIGH
2.0
2.0
2.0
VIL2
Input Voltage Logic LOW
0.8
0.8
0.8
V
IIH2
Input Current Logic HIGH
14
50
30
30
µA
IIL2
Input Current Logic LOW
50
270
110
110
µA
Power Requirements
ICC
Supply Current (+VCC = +5.0V)
(Note 5)
No Load
23
30
28
25
mA
IEE
Supply Current (−VEE = −5.2V)
(Note 5)
No Load
24
31
30
26
mA
PD
Nominal Power Dissipation
No Load
240
PSRR
Power Supply Rejection Ratio
(Note 5)
73
mW
60
64
64
dB
Note 1: “Absolute Maximum Ratings” are those values beyond which the safety of the device cannot be guaranteed. They are not meant to imply that the devices
should be operated at these limits. The table of “Electrical Characteristics” specifies conditions of device operation.
Note 2: Min/max ratings are based on product characterization and simulation. Individual parameters are tested as noted. Outgoing quality levels are determined
from tested parameters.
Note 3: The CLC532 does not require external CCOMP capacitors for proper operation.
Note 4: Absolute maximum ratings are limiting values, to be applied individually, and beyond which the serviceability of the circuit maybe impaired. functional
operability under any of these conditions is not necessarily implied. Exposure to maximum ratings for extended periods may affect device reliability.
Note 5: AJ: 100% tested at +25˚C, sample tested at +85˚C
3
www.national.com
CLC532
Typical Performance Characteristics
(+25˚C unless otherwise specified)
Small Signal/Phase vs. Load
Recommended compensation Capacitance vs. Load
DS012716-5
Small Signal Gain/Phase vs. Load with Recommended
CCOMP
DS012716-6
Large Signal Frequency Response vs. Load
DS012716-8
DS012716-7
SFRD vs. Input Frequency
Output Impedance
DS012716-10
DS012716-9
www.national.com
4
(+25˚C unless otherwise specified) (Continued)
Channel to Channel Crosstalk
Digitized Pulse Response
CLC532
Typical Performance Characteristics
DS012716-12
DS012716-11
Input Impedance
Small Signal Pulse Response
DS012716-14
DS012716-13
Large Signal Pulse Response vs. Ccomp
Large Signal Pulse Response vs. RL
DS012716-15
DS012716-16
5
www.national.com
CLC532
Typical Performance Characteristics
(+25˚C unless otherwise specified) (Continued)
Settling Time vs Ccomp
Settling Time vs. RL
DS012716-24
DS012716-17
2nd and 3rd Harmonic Distortion
2nd Harmonic Distortion vs. VOUT; RL = 100Ω
DS012716-18
3rd Harmonic Distortion vs. VOUT; RL = 100Ω
DS012716-19
Reverse Transmission (S12)
DS012716-21
DS012716-20
www.national.com
6
(+25˚C unless otherwise specified) (Continued)
2nd Harmonic Distortion vs. VOUT; RL = 500Ω
3nd Harmonic Distortion vs. VOUT; RL = 500Ω
DS012716-22
Differential Phase vs. Frequency (Negative Sync)
DS012716-23
Differintial Gain vs. Frequency (Negative Sync)
DS012716-25
2- Tone, 3rd Order Intermodulation Intercept
CLC532
Typical Performance Characteristics
DS012716-26
Transient Isolation
DS012716-28
DS012716-27
7
www.national.com
CLC532
Typical Performance Characteristics
(+25˚C unless otherwise specified) (Continued)
Equivalent Input Noise
Integral Linearity Error
DS012716-29
DS012716-30
Switching Transient (Grounded Inputs)
Large signal Channel-to-Channel Switching
DS012716-31
DS012716-32
Typical DS Error vs. Temperature
DS012716-33
www.national.com
8
CLC532
Application Information
Digital Interface and Channel SELECT
System Timing Diagram
The CLC532 functions with ECL, TTL and CMOS logic families, DREF controls logic compatibility. In normal operation,
DREF is left floating, and the channel SELECT responds to
ECL level signals, Figure 2. For TTL or CMOS level SELECT
inputs (Figure 3), DREF should be tied to +5V (the CLC532
incorporates an internal 2300Ω series isolation resistor for
the DREF input). For TTL or CMOS operation, the channel
SELECT requires a resistor input network to prevent saturation of the channel select circuitry. Without this input network, channel SELECT logic levels above 3V will cause
internal junction saturation and slow switching speeds.
SETTLING ERROR
WINDOW
A
SELECT
B
TSx
SWT90
SWT10
TRx
TRx
90%
OUTPUT
10%
CHANNEL A = +1V
CHANNEL B = - 1V
OS
... where TSx i s TS14 or TSP or TSS,
and TRx i s TRS ro TSL.
DS012716-34
System Transient Timing Diagram
A
SELECT
B
~
~ 2ns
ST
OUTPUT
Channel A = 0V
Channel B = 0V
DS012716-37
DS012716-35
FIGURE 2. ECL Level Channel SELECT Configuration
Operation
The CLC532 is a 2:1 analog multiplexer with high impedance
buffered inputs, and a low distortion, output stage. The
CLC532 employs a closed-loop design, which dramatically
improves distortion performance. The channel SELECT control Figure 1 determines which of the two inputs (INA or INB)
is present at the OUTPUT. Beyond the basic multiplexer
function, the CLC532 offers compatibility with either TTL or
ECL logic families, as well as adjustable bandwidth.
+5V
+6.8 µ F
0.1 µ F
DS012716-38
CHANNEL A
2
INA
1
13
14
RIN
12
11
CLC532
CHANNEL B
RIN
FIGURE 3. TTL/CMOS Level Channel SELECT
Configuration
CCOMP1
4
INB
3
10
5
7
8
9
Compensation
The CLC532 incorporates compensation nodes that allow
both its bandwidth and its settling time/slew rate to be adjusted. Bandwidth and settling time/slew adjustments are
linked, meaning that lowering the bandwidth also lowers
slew rate and lengthens settling time. Proper compensation
is necessary to optimize system performance. Time domain
applications should generally be optimized for lowest RMS
noise at the CLC532 output, while maintaining settling time
and slew rate at adequate levels to meet system needs.
Frequency Domain applications should generally be optimized for maximally flat frequency response.
VOUT
6
RL
DREF
CCOMP2
DGND
+6.8 µ F
CHANNEL
SELECT
0.1µF
-5. 2V
DS012716-36
FIGURE 1. Standard CLC532 Circuit Configuration
9
www.national.com
CLC532
Application Information
plane will provide the best performance. In those special
cases requiring separate ground planes, the following table
indicates the signal and supply ground connections.
(Continued)
Figure 4 below describes the basic relationship between
settling time (TS) and RS for various values of load capacitance, CL, where CCOMP = 10pF
Pin
Functions
Ground Return
1,3
Shield/Supply Returns
Supplies and
Inputs
5
DREF Ground
DREF Currents
only
Input Shielding
The CLC532 has been designated for use in high speed
wide dynamic range systems. Guarding traces and the use
of the ground pins separating the analog inputs are recommended to maintain high isolation (Figure 6). Likely sources
of noise and interference that may couple onto the inputs,
are the logic signals and power supplies to the CLC532.
Other types if clock and signal traces should not be overlooked, however.
Channel A
Connector
DS012716-39
FIGURE 4. Settling Time and RS vs. CL
Figure 5 shows the resulting changes in bandwidth and slew
rate for increasing values of CCOMP. The RMS noise at the
CLC532 output can be approximated as:
Pin 1
Chip Resistors
where.... nV = input spot noise voltage;
BW−3dB = Bandwidth is from Figure 5.
Channel B
Connector
DS012716-42
FIGURE 6. Alternate Layout Using Guard Ring
The general rule in maintaining isolation has two facets,
minimize the primary return ground current path impedances
back to the respective signal sources, while maximizing the
impedance associated with common or secondary ground
current return paths. Success or failure to optimize input
signal isolation can be measured directly as the isolation
between the input channels with the CLC532 removed from
circuit. The channel-to -channel isolation of the CLC532 can
never be better than the isolation level present at its inputs.
Special attention must be paid to input termination resistors.
Minimizing the return current path that is common to both of
the input termination resistors is essential. In the event that a
ground return current from one input termination resistor is
able to find a secondary path back to its signal source (which
also happens to be common with either the primary or secondary return path for the second input termination resistor),
a small voltage can appear across the second input termination resistor. The small voltage seen across the second
input termination resistor will be highly correlated with the
signal generating the initial return currents. This situation will
severely degrade channel-to-channel isolation at the input of
the CLC532, even if the CLC532 were removed from circuit.
Poor isolation at the input will be transmitted directly to the
output.
Use of “small” value input termination resistors will also
improve channel-to-channel isolation. However, extremely
low values ( < 25Ω) tend to stress the driving source’s ability
to provide a high-quality input signal to the CLC532. Higher
values tend to aggravate any layout dependent crosstalk.
75Ω to 50Ω is a reasonable target, but the lower the better.
DS012716-41
FIGURE 5. CCOMP for Maximally Flat Frequency
Response
Power Supplies and Grounding
Proper power supply bypassing and grounding is essential
to the CLC532’s operation. 0.1µF to .1µF ceramic chip capacitor should be located very close to the individual power
supply pins. Larger +6.8µF tantalum capacitors should be
used within a few inches of the CLC532. The ground connections for these larger by-pass capacitors should be symmetrically located relative the CLC532 output load ground
connection. Harmonic distortion can be heavily influenced by
non-symmetric decoupling capacitor grounding. The smaller
chip capacitors located directly at the power supply pins are
not particularly susceptible to this effect.
Separation of analog and digital ground planes is not recommended. In most cases, a single low impedance ground
www.national.com
10
CLC532
Application Information
(Continued)
50
Combining Two Signals in ADC Applications
45
The CLC532 is applicable in a wide range of circuits and
applications. A classic example of this flexibility is combining
two or more signals for digitization by an analog-to-digital
converter (ADC). A clear understanding of both the multiplexer and the ADC’S operation is needed to optimize this
configuration.
To obtain the best performance from the combination, the
output of the CLC532 must be an accurate representation of
the selected input during the ADC conversion cycle. The
time at which the ADC saples the input varies with the type is
ADC that is being used.
Subranging ADCs usually have a Track-and-Hold (T/H) at
their input. For a successful combination of the multiplexer
and the ADC, the multiplexer timing and the T/H timing must
be compatible. When the ADC is given a converter command, the T/H transitions from all caps Track mode to all
caps Hold mode. The delay between the converter command and this transition is usually specified as Aperture
Delay or as Sampling Time Offset.
To maximize the time that the multiplexer output has to
settle, and that the T/H has to acquire the signal, the multiplexer should begin its transition from one input to the other
immediately after the T/H transition into HOLD mode. Unfortunately it is during the initial portion of the HOLD period that
a subranging ADC performs analog processing of the
sampled signal. High slew rate transitions on the input during
this time may have a detrimental effect on the conversion
accuracy.
To minimize the effects of high input slew rates, one of two
strategies that can employed. Strategy one applies when the
sampling rate of the system is below the rated speed of the
ADC. For this case, the CLC532 SELECT timing is delayed
until after the multiplexer transition takes place, while the A/D
has completed one conversion cycle and is waiting for the
next convert command. As an example, if a CLC935
(15MSPS) ADC is being used at 10MSPS, the conversion
takes place in the first 67ns after the CONVERT command.
The next 33ns are spent waiting for the next CONVERT
command. This quite period would be an ideal place to
switch the multiplexer from one channel to the next.
Ccomp (pF)
40
35
30
25
20
15
10
5
10
11
12
13 14 15 16 17
Sample Rate (MSPS)
18
19
20
DS012716-43
FIGURE 7. Recommend CCOMP vs. ADC Sample Rate
Strategy two involves lowering the slew rate at the input of
the ADC so that less high frequency to feed through to the
hold capacitor during HOLD mode. The CLC532 output signal can be slew limited by increasing its compensation capacitors. This approach also has the advantage of limiting
the excess noise passed through the CLC532 to the ADC.
Figure 7 shows the recommended CCOMP values as a function of ADC sample rate. Since the optimal values will
change from one ADC type to the next, this graph should be
used as a starting point for CCOMP selection. Both CCOMP
capacitors should be the same value to maintain output
symmetry.
Flash ADCs are similar to subranging ADCs in that the
sampling period is very brief. The primary difference is that
the acquisition time of a flash converter is much shorter than
that of a subranging ADC. It is only during this period that a
flash converter is susceptible to interference from a rapidly
changing analog input signal. With a flash ADC, the transition of the CLC532 output should be after the sampling
instant (”See timing diagram for ADC Aperture Delay” after
the CONVERT command).
Gain selection for an ADC
In many applications, such as RADAR, the dynamic range
requirements may exceed the accuracy requirements. Since
wide dynamic range ADC are also typically high accuracy
ADCs, this often leads the designer into wrongly selecting an
ADC which is a technical overkill and a budget buster. By
using the CLC532 as a selectable-gain stage, a less expensive ADC can be used. As an example, if an application calls
for 80dB of dynamic Range and 0.05% accuracy, rather than
using a 14-bit converter, a 12-bit converter combined with
the circuit in Figure 8 will meet the same objective. The
CLC532 is used to select between the analog input signal
and a version of the input signal attenuated by 12dB. The
circuit affords 14-bit dynamic range, 12-bit accuracy and
12-bit ease of implementation.
11
www.national.com
CLC532
Application Information
(Continued)
+5V
+6.8µ F
0.1µF
To 0Ω
Input
Source
50 Ω
R7
2
INA
1
10pF
13
14
12
200 Ω
R6
66.6 Ω R INB
To 50 Ω
Source
11 48.7 Ω
CLC532
4
IN
3 B
6
10
5
7
8
To 50 Ω
Load
R OUT
DREF
9
10pF
DGND
50 Ω
+6.8 µ F
Gain
SELECT
0.1µF
-5.2V
DS012716-44
FIGURE 8. Selectable Gain Stage Improves ADC Dynamic Range
full wave rectifier. The circuit inFigure 9 is used to select
between an analog input signal and an inverted version of
the input signal. The resulting output exhibits very little distortion for small scale signals up to several hundred
kilohertz.
Full Wave Rectifier Circuit
The use of a diode rectifierintroduces significant distortion
for signals that are small compared to the diode forward bias
voltage. Therefore, when low distortion performance is
needed, standard diode based circuits do not work well. The
CLC532 can be configured to provide a very low distortion
+1
INA
RECTIFIER
INPUT
CLC532
RL
INB
-1
VOUT
10114
+20
50Ω
0.1µF
VBB
50Ω
50Ω
50Ω
-2V
Zero Crossing
Tr eshold
Detector
DS012716-45
FIGURE 9. Low Distortion Full Wave Rectifier
the CLC532 circuit shown in Figure 11. The CLC532 based
circuit uses a digital LO making system design easier in
those cases where the LO is digitally derived. Another advantage of the CLC532 based approach is excellent isolation
between all three ports. (See the RF design awards article
by Thomas Hack in January 1993 of RF Design.)
Use of the CLC532 as a Mixer
A double balanced diode bridge mixer, as shown in Figure
10, operates by multiplying the RFsignal input by the LO
input signal . This is done by using the LO signal phase to
select either the forward or reverse path through the diode
bridge. The result is an output where IF=RF when LO > 0 and
IF=−RF for LO < 0. The same function can be obtained with-
www.national.com
12
CLC532
Application Information
(Continued)
DS012716-46
FIGURE 10. Typical Double-Balanced Mixer
DS012716-47
FIGURE 11. High-Isolation Mixer Implementation
Evaluation Board
An evaluation board (part number 730028) for CLC532 is
available. This board can be used for fast, trouble-free,
evaluation and characterization of the CLC532. Additionally,
this board serves as a template for layout and fabrication
information.
13
www.national.com
CLC532
Physical Dimensions
inches (millimeters) unless otherwise noted
NS Package Number M14A
NS Package Number N14A
www.national.com
14
CLC532 High Speed 2:1 Analog Multiplexer
Notes
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT
DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL
COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein:
1. Life support devices or systems are devices or
systems which, (a) are intended for surgical implant
into the body, or (b) support or sustain life, and
whose failure to perform when properly used in
accordance with instructions for use provided in the
labeling, can be reasonably expected to result in a
significant injury to the user.
National Semiconductor
Corporation
Americas
Email: [email protected]
www.national.com
National Semiconductor
Europe
Fax: +49 (0) 180-530 85 86
Email: [email protected]
Deutsch Tel: +49 (0) 69 9508 6208
English Tel: +44 (0) 870 24 0 2171
Français Tel: +33 (0) 1 41 91 8790
2. A critical component is any component of a life
support device or system whose failure to perform
can be reasonably expected to cause the failure of
the life support device or system, or to affect its
safety or effectiveness.
National Semiconductor
Asia Pacific Customer
Response Group
Tel: 65-2544466
Fax: 65-2504466
Email: [email protected]
National Semiconductor
Japan Ltd.
Tel: 81-3-5639-7560
Fax: 81-3-5639-7507
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.
Similar pages