7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. ATLANTIC VERSION TERMINATOR INTERFACE ADAPTER 5 4 3 2 20 SET UP GAUGE 2119599-2 ALL RIGHTS RESERVED. PART NUMBER REVISION 2150045 -1 DESCRIPTION A 2150045 -2 2150045 -7 A FINE CRIMP HEIGHT ADJUST 4 NONE CRIMP TOOLING KIT - 2119792-2 SMART APPLICATOR 2161326-1 - SERVO LATCH PLATE SMART APPLICATOR SERVO LATCH PLATE 12 NON-CRIMP HEIGHT ADJUST A PNEUMATIC FINE CRIMP HEIGHT ADJUST A 2119950-1 MECHANICAL FEED 4 MECHANICAL FEED PNEUMATIC FEED - 2119951-1 2119949-1 2119951-1 2161326-1 2119949-1 2119950-1 - - - 1901697-1 2063961-1 1901697-1 - 2063961-1 2119792-2 - - 2119641-1 - CRIMP WIRE INSUL SIZE 8- 2150045 -4 - - 8- 2150045 -5 5-18022-5 8- 2150045 -5 8- 2150045 -4 5-18022-5 - - - - - 2119653-1 - - 2119653-1 2119641-1 - - - - 2168400-7 3.05 mm [.120] APPL INSTRUCTIONS 408-10390 2168400-7 - - - (QUANTITY 2) - 2063440-2 - - - TE CRIMP SPECIFICATION RING TERMINAL TERMINAL NAME: WIRE STRIP LENGTH n 5.56-6.00 mm [.219-.236 IN] C TERMINAL APPLICATION SPECIFICATION 114-2084 - INSULATION DIAMETER RANGE 1.40-2.10 mm [.055-.083 IN] - - - - TERMINALS APPLIED TE TERMINAL 346100-2 WIRE SIZE 1.00mm2 0.75mm2 0.50mm2 1 2 B 6 TE TERMINAL C1__DWG_PN_1_0 346100-3 C1__DWG_PN_1_1 C1__DWG_PN_2_0 TE TERMINAL C1__DWG_PN_2_1 W1__DWG_WGAUGE_2 W1__DWG_WGAUGE_3 1.89+/-0.05 [.074+/-.002] 1.82+/-0.05 [.072+/-.002] 1.75+/-0.05 [.069+/-.002] C1__DWG_PN_4_0 C1__DWG_PN_3_1 CRIMP HEIGHT REFERENCE SETTING CRIMP HEIGHT mm [INCH] W1__DWG_WGAUGE_1 TE TERMINAL C1__DWG_PN_3_0 W1__DWG_CRIMP_HT_2 W1__DWG_CRIMP_HT_3 9 9.6 W1__DWG_CRIMP_HT_1 W1__FA_SETTING_1 10.1 W1__FA_SETTING_2 10.7 W1__FA_SETTING_3 *WARNING ON INSTALLATION, SET WIRE DISC, ITEM 40 TO LARGEST WIRE SIZE SETTING. USE OF SETTINGS BELOW MINIMUM REQUIRED CRIMP HEIGHT SETTING WILL CAUSE DAMAGE TO CRIMP TOOLING. RECOMMENDED SPARE PARTS GREASE BEARING SURFACES LIGHTLY 3. LUBRICATE DAILY PER THE APPLICATOR INSTRUCTION SHEET SUPPLIED WITH THE APPLICATOR. 4 APPLICATOR SPECIFIC DATA TO BE ENTERED INTO BLANK MEMORY CHIP AT ASSEMBLY. SEE BELOW FOR PART NUMBER: MECHANICAL FEED WITH "SMART APPLICATOR" CONVERSION: 8PNEUMATIC FEED WITH "SMART APPLICATOR" CONVERSION: 8SERVO FEED WITH "FINE CRIMP HEIGHT ADJUST": 8SERVO FEED WITH "NON-CRIMP HEIGHT ADJUST": 8- 2150045 2150045 2150045 2150045 6 -4 -4 -5 -6 5. ADJUSTMENT OF THE STRIPPER MAY BE REQUIRED WHEN MOVING THE APPLICATOR BETWEEN BENCH AND LEADMAKER APPLICATIONS. 6 7 8 9 10 11 A 12 APPLY PART NUMBER 1-23419-5 LOCTITE TO THREADS OF ITEM 37, 62 FOR -6 ONLY APPLY PART NUMBER 1-23419-5 LOCTITE TO THREADS OF ITEMS 37, GREASE THREADS, GROOVE AND O-RING ON ITEMS 35 & 242. & 242. & 252. 1 MAGNET, ITEM 166 MUST BE ORIENTED CORRECTLY IN ORDER TO PROPERLY ACTUATE THE COUNTER. 1 1 CRIMP HEIGHT REFERENCE SETTING WAS THE SETTING USED WHEN THE APPLICATOR WAS QUALIFIED AT THE FACTORY. ADJUSTMENT MAY BE NECESSARY WHEN RUNNING APPLICATOR IN THE FIELD. 1 SPARE FEED CAM STORAGE LOCATION REFER TO INSTRUCTION SHEET FOR ADDITIONAL INFORMATION. THE ITEM ITEM FEED 1 RECOMMENDED SET-UP FOR END FEED APPLICATORS IS POST-FEED WITH 2119653-1. THE APPLICATOR CAN BE CONFIGURED FOR PRE-FEED WITH 2119652-1 BUT MAY ENCOUNTER PROBLEMS WITH SOME APPLICATIONS. ISSUES OR TERMINAL JAMMING MAY OCCUR IN THE PRE-FEED CONFIGURATION. WHEN ASSEMBLING -6 NON-CRIMP HEIGHT ADJUST APPLICATOR USE SHIM PACK 2119957-2 TO ALIGN APPLICATOR'S MAXIMUM WIRE CRIMP HEIGHT AT NORMAL TERMINATOR SHUT HEIGHT 1 - - 1 - - - 1 - 1 1 1 - - - - 1 - - - - 1 - - - - 1 - 1 - 1 1 1 - 1 - 1 1 1 - - 1 - - - 1 1 1 1 1 - 1 1 1 1 1 - 1 1 1 1 1 - - 2 2 - - - - - - 1 - - - - 1 - - 1 1 - - - REF REF - - - - - 2 - 1 1 1 1 1 - REF REF REF REF REF - - - - 1 - - - - 1 - - REF REF - - - 1 1 - - 1 1 1 1 1 - 1 1 1 1 1 - 2 2 2 2 2 - 1 - - 1 1 - 2 2 2 2 2 - 1 - 1 1 1 - 3 - 3 3 3 - 1 1 1 1 1 - - - - - 1 - - - - - 1 - 4 4 4 4 4 - 2 2 2 2 2 - 2 2 2 2 2 - 2 2 2 2 2 - 2 2 2 2 2 - - - - 1 - - - - 1 2 - - - - - 1 - - - - - 1 - 1 1 1 1 1 - 1 - 1 1 1 - 1 1 1 1 1 - 1 - 1 1 1 - 1 - 1 1 1 - 1 1 1 1 1 - 1 1 1 1 1 - 1 - 1 1 1 - 8 8 8 8 8 - 2 2 2 2 2 - 2 2 2 2 2 - 1 1 1 1 1 - 2 2 2 2 2 - 1 1 1 1 1 - 2 2 2 2 2 - 1 1 1 1 1 - 1 1 1 1 1 - 1 1 1 1 1 - 4 4 4 4 4 - 1 1 1 1 1 - - - - - - 1 1 1 1 1 1 1 1 1 1 1 - 1 1 1 1 1 - 1 1 1 1 1 - 1 1 1 1 1 1 1 1 1 1 1 - 1 1 1 1 1 1 1 1 1 1 1 LTR DESCRIPTION DATE DWN APVD 1 DEVELOPMENT 30JUN2012 XZ SX 2 CORRECT 26APR2013 CC UG A RELEASED 28AUG2013 BH TE 2119957-2 8-21084-0 2119640-1 2079988-1 2119641-1 2119798-1 1-22279-3 2119759-1 2119082-9 2079764-1 2119083-1 2168400-7 2119580-1 2063440-2 2119740-2 1901697-1 21045-3 994969-1 994970-2 240638-1 3-23627-7 SEE NOTE 4 1633743-1 455888-4 2119956-2 2-18032-2 2119740-1 2168078-1 2119793-1 992763-5 2079383-4 5-18022-5 2063961-1 2168400-4 2168083-3 5018030-2 5018030-1 986965-8 2119792-2 18023-9 2119652-1 2119653-1 2119655-5 2119369-1 2079383-7 2119645-1 2119957-1 2119644-2 2119085-1 2119092-1 1-18028-2 2168083-9 1-2168083-0 240639-1 1320906-1 1752371-5 2-22281-3 1752373-4 1901696-9 1901695-9 1-2079383-1 240644-1 690482-5 1803000-4 2217206-7 1-240641-5 238009-1 1-2119785-9 1-455888-5 1-456407-0 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 2 1 1 1 1 1 1 1 1 2 1 2 1 3 1 1 1 4 2 2 2 2 1 3 1 1 1 1 1 1 1 1 1 1 8 2 2 1 2 1 2 1 1 1 4 1 1 1 1 1 1 1 1 1 1 -77 -7 -6 -5 -2 -1 PART NO THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. DIMENSIONS: ATLANTIC VERSION Shown on sheets 1 of 4 & 2 of 4 (Pacific version shown on sheets 3 of 4 AMP 4805 REV 31MAR2000 P - TYPE TE TERMINAL TERMINAL DATA: 66 (QUANTITY 2) F OV 2.54 mm [.100] A REVISIONS DIST 2063440-2 6 APPLICATOR DATA LOC 1 PART NUMBERS REQUIRED PNEUMATIC FEED SERVO LATCH PLATE SERVO LATCH PLATE 2150045 -6 7- 2150045 -7 CONVERT TO MECHANICAL FINE CRIMP HEIGHT ADJUST A APPLICATOR STYLE CONVERSION CHART FEED TYPE FINE CRIMP HEIGHT ADJUST A 2150045 -5 D 6 mm & 4 of 4) MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: 0.5 0.13 0.013 0.0001 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - DWN 30JUN2012 CHK 30JUN2012 APVD 30JUN2012 X.ZHAO T.ELBIN S.XI TE Connectivity Harrisburg, PA 17105-3608 NAME - APPLICATION SPEC - WEIGHT SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 3 ITEM NO DESCRIPTION PRODUCT SPEC - 260 252 250 249 248 247 246 245 244 243 242 240 239 238 213 183 172 166 164 163 137 135 133 82 71 70 67 66 63 62 60 59 58 57 56 55 54 53 51 49 48 47 46 44 41 40 39 38 37 35 33 31 29 27 25 24 22 20 19 18 17 11 10 9 8 7 5 4 3 2 1 APPLICATOR SHIM PACK O-RING, .676 ID, .070 DIA. MAT. PUSH ROD, AIR FEED BUSHING, LCH5-12, MISUMI FEED CAM, AIR FEED DETENT PIN SPRING, COMPRESSION RAM, AMP STYLE, END FEED, NON-ADJUST CAM, SNAIL, INSULATION ADJUSTMENT WASHER, WAVE SPRING, CREST-TO-CREST RETAINER, INSULATION DIAL SHCS, LOW HEAD, RoHS, M5 X 10 MECHANICAL FEED ASSEMBLY AIR FEED MODULE TAG,IDENTIFICATION FEED FINGER ASSEMBLY,EF RING, RETAIN, EXTERN, 3/16 CRESCENT MAGNET, RARE EARTH HIGH ENERGY COUNTER, MAGNETIC SPRING, FEED FINGER PIN, RETAIN, GRVD, 3/16 X .854 MEMORY CHIP, PROGRAMMED SERVO FEED LATCH ASM SPACER, CRIMPER DOCUMENTATION PACKAGE SCR, SET, FLT POINT M3 X 10.0 TAG,IDENTIFICATION SCREW, DRIVE, RH, RoHS, 2 x .188 LIMITER, ADJUSTMENT BOLT SCR, SET, SOC, CONE POINT, M3 x 4.0 SCR, BHSC, RoHS (M4 X 8) SCR, HEX HD CAP, M4 X 6.0 FEED FINGER SHCS, LOW HEAD, RoHS, M4 X 8 SCR, SKT HD CAP, RoHS, M4 X 12.0 NUT, HEX, REG, RoHS, M4 NUT, HEX, REG, RoHS, M3 NUT, LOCK, HEX, TORQUE (M4) PAWL, EF, AIR SCR, SKT HD CAP M4 X 6.0 FEED CAM, PRE FEED FEED CAM, POST FEED APPLICATOR BASIC ASSEMBLY, EF RAM,AMP STYLE, END FEED SCR, BHSC, RoHS (M8 X 25) DISC, NUMBERED FA WIRE ADJUSTMENT APPLICATOR SHIM PACK RAM WASHER, PRECISION FA HEAD, ATLANTIC STYLE BOLT, ADJUSTMENT WASHER, FLAT, REG M4 SCR, SKT HD CAP, RoHS, M4 X 20 SCR, SKT HD CAP, RoHS, M4 X 10 STRIPPER (MACHINING) STUD, THREADED PLATE, STRIP GUIDE SPRING, COMPRESSION DRAG STRIP GUIDE, REAR STRIP GUIDE, FRONT SCR, BHSC, RoHS (M6 X 12) PLATE, REAR SHEAR PLATE, FRONT SHEAR ANVIL, COMBINATION, END FEED BLADE, SLUG SPACER BLOCK, FL CRIMPER SPACER CRIMPER, INSULATION OVERLAP PREMIUM SPACER, CRIMPER CRIMPER, WIRE PREMIUM Ocean End Feed Applicator - DRAWING NO 2150045 SCALE 1:1 RESTRICTED TO SHEET 1 OF - 4 & 4 ARE NOT REQUIRED FOR ATLANTIC VERSION REV A D C B A 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. 6 5 4 3 2 20 LOC REVISIONS DIST A ALL RIGHTS RESERVED. 1 66 P LTR - 6 DESCRIPTION DATE SEE SHEET 1 DWN APVD - - - 37 40 6 FEED TYPE 62 MECHANICAL 38 D 39 247 260 7 7 243 6 2 2 246 252 2 245 35 56 A 2 44 244 D 7 2 1 239 59 5 242 166 58 8 63 82 1 1 PNEUMATIC 2 C 3 C 238 1 250 249 70 4 41 2 A 54 137 55 163 172 10 2 A 164 20 51 57 33 19 67 B SERVO LATCH PLATE 18 213 66 B CAM POSITIONS 30mm STROKE 30mm STROKE 30mm STROKE 29 47 A 33 27 8 1 46 60 31 9 1 11 1 17 53 33 25 22 24 248 48 4 135 133 183 240 REF 49 49 A 49 THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. 40mm STROKE MECHANICAL POST FEED AMP 4805 REV 31MAR2000 SERVO FEEDER NOT INCLUDED A 40mm STROKE MECHANICAL PRE FEED 40mm STROKE 11 AIR FEED DIMENSIONS: ATLANTIC VERSION Shown on sheets 1 of 4 & 2 of 4 (Pacific version shown on sheets 3 of 4 mm & 4 of 4) MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: 0.5 0.13 0.013 0.0001 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - DWN 30JUN2012 CHK 30JUN2012 APVD 30JUN2012 X.ZHAO T.ELBIN S.XI TE Connectivity Harrisburg, PA 17105-3608 NAME PRODUCT SPEC - APPLICATION SPEC - - WEIGHT SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 3 Ocean End Feed Applicator - DRAWING NO 2150045 SCALE 1:1 RESTRICTED TO SHEET 2 OF & 4 ARE NOT REQUIRED FOR ATLANTIC VERSION - 4 REV A 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. PACIFIC VERSION TERMINATOR INTERFACE ADAPTER 5 4 3 2 20 SET UP GAUGE 2119599-2 ALL RIGHTS RESERVED. PART NUMBER REVISION 2- 2150045 -1 DESCRIPTION A 2- 2150045 -2 D 6 FEED TYPE FINE CRIMP HEIGHT ADJUST A FINE CRIMP HEIGHT ADJUST FINE CRIMP HEIGHT ADJUST SERVO LATCH PLATE 2- 2150045 -7 A FINE CRIMP HEIGHT ADJUST NONE CRIMP TOOLING KIT PNEUMATIC FEED - 2119792-2 2119641-2 - 8- 2150045 -4 - - 8- 2150045 -5 MECHANICAL FEED 2119949-1 2063961-1 5-18022-5 2119653-2 8- 2150045 -4 - MECHANICAL FEED PNEUMATIC FEED - - CRIMP WIRE INSUL SIZE 2161326-1 2119951-1 2161326-1 2119949-1 2119950-1 - - - 1901697-1 - 2063961-1 2119792-2 - - 8- 2150045 -5 5-18022-5 - - - - 2119653-2 2119641-2 - - - 2168400-7 3.05 mm [.120] APPL INSTRUCTIONS 408-10390 WIRE STRIP LENGTH n 5.56-6.00 mm [.219-.236 IN] C TERMINAL APPLICATION SPECIFICATION 114-2084 2168400-7 - - (QUANTITY 2) - - 2063440-2 - - - INSULATION DIAMETER RANGE 1.40-2.10 mm [.055-.083 IN] - - - - TERMINALS APPLIED TE TERMINAL 346100-2 WIRE SIZE 1.00mm2 0.75mm2 0.50mm2 B TE TERMINAL C1__DWG_PN_1_0 346100-3 C1__DWG_PN_1_1 C1__DWG_PN_2_0 TE TERMINAL C1__DWG_PN_2_1 W1__DWG_WGAUGE_2 W1__DWG_WGAUGE_3 1.89+/-0.05 [.074+/-.002] 1.82+/-0.05 [.072+/-.002] 1.75+/-0.05 [.069+/-.002] 1 RECOMMENDED SPARE PARTS 2 GREASE BEARING SURFACES LIGHTLY TE TERMINAL C1__DWG_PN_4_0 C1__DWG_PN_3_1 CRIMP HEIGHT REFERENCE SETTING CRIMP HEIGHT mm [INCH] W1__DWG_WGAUGE_1 C1__DWG_PN_3_0 W1__DWG_CRIMP_HT_1 W1__DWG_CRIMP_HT_2 W1__DWG_CRIMP_HT_3 9.6 10.1 10.7 6 9 W1__FA_SETTING_1 W1__FA_SETTING_2 W1__FA_SETTING_3 *WARNING ON INSTALLATION, SET WIRE DISC, ITEM 40 TO LARGEST WIRE SIZE SETTING. USE OF SETTINGS BELOW MINIMUM REQUIRED CRIMP HEIGHT SETTING WILL CAUSE DAMAGE TO CRIMP TOOLING. 3. LUBRICATE DAILY PER THE APPLICATOR INSTRUCTION SHEET SUPPLIED WITH THE APPLICATOR. 4 APPLICATOR SPECIFIC DATA TO BE ENTERED INTO BLANK MEMORY CHIP AT ASSEMBLY. SEE BELOW FOR PART NUMBER: MECHANICAL FEED WITH "SMART APPLICATOR" CONVERSION: 8PNEUMATIC FEED WITH "SMART APPLICATOR" CONVERSION: 8SERVO FEED WITH "FINE CRIMP HEIGHT ADJUST": 8- 2150045 -4 2150045 -4 2150045 -5 5. ADJUSTMENT OF THE STRIPPER MAY BE REQUIRED WHEN MOVING THE APPLICATOR BETWEEN BENCH AND LEADMAKER APPLICATIONS. 6 APPLY PART NUMBER 1-23419-5 LOCTITE TO THREADS OF ITEMS 62 7 GREASE THREADS, GROOVE AND O-RING ON ITEMS 139 8 9 10 A 1 & 242. 1 & 153. 1 MAGNET, ITEM 166 MUST BE ORIENTED CORRECTLY IN ORDER TO PROPERLY ACTUATE THE COUNTER. 1 CRIMP HEIGHT REFERENCE SETTING WAS THE SETTING USED WHEN THE APPLICATOR WAS QUALIFIED AT THE FACTORY. ADJUSTMENT MAY BE NECESSARY WHEN RUNNING APPLICATOR IN THE FIELD. 1 SPARE FEED CAM STORAGE LOCATION REFER TO INSTRUCTION SHEET FOR ADDITIONAL INFORMATION. 11 THE RECOMMENDED SET-UP FOR END FEED APPLICATORS IS POST-FEED WITH ITEM 2119653-1. THE APPLICATOR CAN BE CONFIGURED FOR PRE-FEED WITH ITEM 2119652-1 BUT MAY ENCOUNTER PROBLEMS WITH SOME APPLICATIONS. FEED ISSUES OR TERMINAL JAMMING MAY OCCUR IN THE PRE-FEED CONFIGURATION. 1 - 1 1 1 1 - - - 1 - - - 1 - 1 1 1 1 - 1 1 1 1 - 1 1 1 1 - 1 1 1 1 - - 2 - - - - - 1 - - - 1 - - 1 - - 4 4 4 4 - - REF - - - - 2 - 1 1 1 1 - REF REF REF REF - - - 1 - 1 1 1 1 - - - 1 - 1 1 1 1 - 1 1 1 1 - - - - 1 - 1 1 1 1 - 1 1 1 1 - 1 1 1 1 - - - 1 - - REF - - - 1 - - 1 1 1 1 - 1 1 1 1 - 2 2 2 2 - 1 - 1 1 - 2 2 2 2 - 1 1 1 1 - 3 3 3 3 - - - - 1 - - - - 1 - 4 4 4 4 - 2 2 2 2 - 2 2 2 2 - 2 2 2 2 - 2 2 2 2 - - - 1 - - - 1 2 - - - - 1 - 1 1 1 1 - 1 1 1 1 - 1 1 1 1 - 1 1 1 1 - 8 8 8 8 - 2 2 2 2 - 2 2 2 2 - 1 1 1 1 - 2 2 2 2 - 1 1 1 1 - 2 2 2 2 - 1 1 1 1 - 1 1 1 1 - 1 1 1 1 - 1 1 1 1 - - - - - 1 1 1 1 1 1 1 1 1 - 1 1 1 1 - 1 1 1 1 - 1 1 1 1 1 1 1 1 1 - 1 1 1 1 1 1 1 1 1 2119782-1 2119640-1 2079988-1 1-22279-3 2119082-9 2079764-1 2119083-1 2168400-7 2119580-1 2063440-2 2119740-2 2079383-9 1901697-1 21045-3 994969-1 994970-2 240638-1 8-21084-1 2119641-2 2119798-2 2079383-8 2119653-2 2119655-6 2119651-1 2119092-2 3-23627-7 SEE NOTE 4 1633743-1 455888-4 2119956-2 2-18032-2 2119740-1 2168078-1 2119793-1 992763-5 5-18022-5 2063961-1 2168400-4 2168083-3 5018030-2 5018030-1 986965-8 2119792-2 18023-9 2119652-1 2079383-7 2119645-1 2119957-1 2119644-2 1-18028-2 2168083-9 1-2168083-0 240639-1 1320906-1 1752371-5 2-22281-3 1752373-4 1901696-9 1901695-9 240644-1 690482-5 1803000-4 2217206-7 1-240641-5 238009-1 1-2119785-9 1-455888-5 1-456407-0 1 1 1 1 1 1 1 2 1 1 1 4 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 2 1 3 1 1 4 2 2 2 2 1 3 1 1 1 1 1 8 2 2 1 2 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 -77 -27 -25 -22 -21 PART NO THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. DIMENSIONS: PACIFIC VERSION Shown on sheets 3 of 4 & 4 of 4 (Atlantic version shown on sheets 1 of 4 AMP 4805 REV 31MAR2000 DATE SEE SHEET 1 DWN APVD - - - - TE CRIMP SPECIFICATION RING TERMINAL TERMINAL NAME: DESCRIPTION - TYPE TE TERMINAL TERMINAL DATA: LTR (QUANTITY 2) F OV 2.54 mm [.100] P 2063440-2 6 APPLICATOR DATA 66 - - 1901697-1 SMART APPLICATOR 4 2119950-1 2119951-1 SERVO LATCH PLATE A REVISIONS DIST PART NUMBERS REQUIRED SERVO LATCH PLATE SMART APPLICATOR PNEUMATIC A A CONVERT TO MECHANICAL 2- 2150045 -5 7- 2150045 -7 APPLICATOR STYLE CONVERSION CHART LOC 1 mm & 2 of 4) MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: 0.5 0.13 0.013 0.0001 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - DWN 30JUN2012 CHK 30JUN2012 APVD 30JUN2012 X.ZHAO T.ELBIN S.XI TE Connectivity Harrisburg, PA 17105-3608 NAME - APPLICATION SPEC - WEIGHT SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 1 ITEM NO DESCRIPTION PRODUCT SPEC - 251 250 249 246 244 243 242 240 239 238 213 186 183 172 166 164 163 153 152 145 144 142 141 140 139 137 135 133 82 71 70 67 66 63 62 59 58 57 56 55 54 53 51 49 48 41 40 39 38 33 31 29 27 25 24 22 20 19 18 11 10 9 8 7 5 4 3 2 1 FINE ADJUST HEAD ASM, PACIFIC STYLE PUSH ROD, AIR FEED BUSHING, LCH5-12, MISUMI SPRING, COMPRESSION CAM, SNAIL, INSULATION ADJUSTMENT WASHER, WAVE SPRING, CREST-TO-CREST RETAINER, INSULATION DIAL SHCS, LOW HEAD, RoHS, M5 X 10 MECHANICAL FEED ASSEMBLY AIR FEED MODULE TAG,IDENTIFICATION SCR, BHSC, RoHS (M6 X 20) FEED FINGER ASSEMBLY,EF RING, RETAIN, EXTERN, 3/16 CRESCENT MAGNET, RARE EARTH HIGH ENERGY COUNTER, MAGNETIC SPRING, FEED FINGER O-RING, .801 ID, .070 DIA. MAT. FEED CAM, AIR FEED DETENT PIN SCR, BHSC, RoHS (M4 X 16) FEED CAM, POST FEED APPLICATOR BASIC ASSEMBLY, EF RAM, ASIAN STYLE, END FEED BOLT, ADJUSTMENT PIN, RETAIN, GRVD, 3/16 X .854 MEMORY CHIP, PROGRAMMED SERVO FEED LATCH ASM SPACER, CRIMPER DOCUMENTATION PACKAGE SCR, SET, FLT POINT M3 X 10.0 TAG,IDENTIFICATION SCREW, DRIVE, RH, RoHS, 2 x .188 LIMITER, ADJUSTMENT BOLT SCR, SET, SOC, CONE POINT, M3 x 4.0 SCR, HEX HD CAP, M4 X 6.0 FEED FINGER SHCS, LOW HEAD, RoHS, M4 X 8 SCR, SKT HD CAP, RoHS, M4 X 12.0 NUT, HEX, REG, RoHS, M4 NUT, HEX, REG, RoHS, M3 NUT, LOCK, HEX, TORQUE (M4) PAWL, EF, AIR SCR, SKT HD CAP M4 X 6.0 FEED CAM, PRE FEED SCR, BHSC, RoHS (M8 X 25) DISC, NUMBERED FA WIRE ADJUSTMENT APPLICATOR SHIM PACK RAM WASHER, PRECISION WASHER, FLAT, REG M4 SCR, SKT HD CAP, RoHS, M4 X 20 SCR, SKT HD CAP, RoHS, M4 X 10 STRIPPER (MACHINING) STUD, THREADED PLATE, STRIP GUIDE SPRING, COMPRESSION DRAG STRIP GUIDE, REAR STRIP GUIDE, FRONT PLATE, REAR SHEAR PLATE, FRONT SHEAR ANVIL, COMBINATION, END FEED BLADE, SLUG SPACER BLOCK, FL CRIMPER SPACER CRIMPER, INSULATION OVERLAP PREMIUM SPACER, CRIMPER CRIMPER, WIRE PREMIUM Ocean End Feed Applicator - DRAWING NO 2150045 SCALE 1:1 RESTRICTED TO SHEET 3 OF - 4 & 2 ARE NOT REQUIRED FOR PACIFIC VERSION REV A D C B A 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. 6 5 4 3 2 20 LOC REVISIONS DIST A ALL RIGHTS RESERVED. 1 66 P LTR - DESCRIPTION DATE SEE SHEET 1 DWN APVD - - - 251 40 6 62 FEED TYPE 38 MECHANICAL 39 D 7 7 145 153 246 139 140 244 2 56 2 2 7 1 2 242 5 63 A 59 243 6 D 239 58 8 166 82 1 C PNEUMATIC 1 2 3 C 238 1 250 249 2 70 4 41 A 54 137 55 163 172 20 10 A 2 51 57 33 164 B 67 19 213 18 SERVO LATCH PLATE 66 B CAM POSITIONS 30mm STROKE 30mm STROKE 30mm STROKE 142 152 SERVO FEEDER NOT INCLUDED A 29 33 27 8 1 141 144 31 9 1 11 1 186 53 33 25 22 24 135 133 4 183 240 REF 48 A A THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. 49 MECHANICAL POST FEED AMP 4805 REV 31MAR2000 49 PACIFIC VERSION 49 MECHANICAL PRE FEED 11 AIR FEED Shown on sheets 3 of 4 & 4 of 4 (Atlantic version shown on sheets 1 of 4 DIMENSIONS: mm & 2 of 4) MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: 0.5 0.13 0.013 0.0001 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - DWN 30JUN2012 CHK 30JUN2012 APVD 30JUN2012 X.ZHAO T.ELBIN S.XI TE Connectivity Harrisburg, PA 17105-3608 NAME PRODUCT SPEC - APPLICATION SPEC - - WEIGHT SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 1 Ocean End Feed Applicator - DRAWING NO 2150045 SCALE 1:1 RESTRICTED TO SHEET 4 OF - 4 & 2 ARE NOT REQUIRED FOR PACIFIC VERSION REV A