Series C60 Optically Isolated 0.5 to 2.5A Bi-Directional Solid-State Relay Part Number Relay Description C60-X0 Solid-State Relay, Terminals for Through Hole Mount SC60-X0 Solid-State Relay, Terminals for Surface Mount Add suffix 01 to denote 60Sn/40Pb Pre-Tinned Leads ELECTRICAL SPECIFICATIONS (25°C UNLESS OTHERWISE SPECIFIED) INPUT (CONTROL) SPECIFICATIONS (See Note 1) Parameter Min Max Units Input Voltage Drop (See Figure 1) 1.1 1.5 Vdc 50 mA Input Current (See Figure 1 and Notes 1, 7) Input Current (Guaranteed On), (See Figure 4 and Note 7) 10 mA Input Current (Guaranteed Off) 100 µA Reverse Voltage Protection -6 Vdc OUTPUT (LOAD) SPECIFICATIONS (See Figure 2 And Note 2) Part Number Parameter Output Voltage Rating DC Min Max Min Bi-Directional Max Units C60-10 60 ±60 Vdc C60-20 100 ±100 Vdc C60-30 200 ±200 Vdc C60-40 400 ±400 Vdc C60-10 2.5 ±1.25 Adc C60-20 1.5 ±0.75 Adc C60-30 1.0 ±0.50 Adc C60-40 0.5 ±0.25 Adc On Resistance C60-10 0.07 0.28 Ohm (See Note 6) C60-20 0.2 0.7 Ohm C60-30 0.45 1.8 Ohm C60-40 1.0 4.0 Ohm Output Current Rating Leakage Current at Rated Voltage 2.0 1.0 µAdc Turn-On Time @ 10mA C60-10 4.0 4.0 ms (See Figure 4 and Note 7) C60-20,-30,-40 3.0 3.0 ms Turn-Off Time C60-10 4.0 4.0 ms C60-20,-30,-40 3.0 3.0 ms Output Capacitance C60-10 1000 500 pf C60-20 500 250 pf C60-30 400 200 pf C60-40 400 200 pf Isolation (Input to Output) 109 Dielectric Strength 1500 109 3.0 Junction Temperature (TJ) 125 BLOCK DIAGRAM Vrms 3.0 pF 125 °C Junction to Case Thermal Resistance 25 °C Case to Ambient Thermal Resistance 75 °C/W © 2010 TELEDYNE RELAYS DESCRIPTION The Series C60 solid-state relay is an advanced design capable of switching very heavy loads in a physically small 6-pin mini DIP package. These relays have a power FET output that ensures low On resistance, no offset voltage and low leakage current. They are versatile and can be used to switch AC, Bi-directional or DC loads. Optical isolation ensures complete protection of signal lines, power and ground bus and control circuits from switching noise and EMI. Ohms 1500 Capacitance (Input to Output) FEATURES/BENEFITS • Power FET Output with Very Low On Resistance: Virtually no offset with very low leakage and voltage drop. • Optical Isolation: Isolates control elements from load transients. Eliminates ground loops and signal ground noise. • Three Terminal Output: Output FETs can be paralleled externally to change current load rating. • Floating Output: Allows for high and low side switching. • Switches High Voltages and Currents: Voltages to 400 Vdc. Current to 2.5 Adc. Bi-directional, DC or AC. • High Noise Immunity: Control circuit cannot be triggered by output switching noise. • 6-Pin Mini-DIP Package: Standard or surface mount available. (800) 284-7007 • www.teledynerelays.com C60 1 2DSC60-X0 Rev -- Series C60 CHARACTERISTIC CURVES MECHANICAL SPECIFICATION WIRING CONFIGURATIONS • Operating Temperature Range: -40°C to 85°C • Storage Temperature Range: -40°C to 100°C • Weight: 1 gm. maximum • Case: 6 pin dual in line, filled epoxy C60 2 NOTES: 1. Series resistor is required to limit input current to 50 mA maximum. 2. The input current is 10 mA for all tests unless otherwise specified. 3. The surge current is non-repetitive for a maximum duration of 20 ms (See Figure 3). 4. Loads may be connected to positive or negative referenced power supplies. Inductive loads must be diode suppressed. 5. Continuous load current is rated under the conditions of still air and mounted on a printed circuit board. 6. To calculate ON Resistance for a given junction temperature calculate the new ROn using the equation shown below: ROn=R(25°C)x e0.006(TJ-25°C) 7. Turn on Time can be controlled with input control current. Calculate a new turn-on time: tOn=(tSpecification Limit)(10mA/IIn) 8. Load voltage rating should be derated 10% at -40°C SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE © 2010 TELEDYNE RELAYS 2DSC60-X0 Rev --