Tel : +44 118 979 1238 Fax : +44 118 979 1283 Email: [email protected] The ACTF4818/479.5/TO39-3 is one channel IF filter for receivers of satellite broadcasting system. 1.Package Dimensions 2. Pin Configuration 1 Input 2 Output 3 Output 4 Ground Dimensions Data (Unit: mm) A 9.35±0.10 B 5.08±0.10 C 3.40±0.10 D 3.00±0.20 E 4-Φ0.45±0.20 3. Measuring Circuit In keeping with our ongoing policy of product evolvement and improvement, the above specification is subject to change without notice. ISO9001: 2000 Registered For quotations or further information please contact us at: 3 The Business Centre, Molly Millars Lane, Wokingham, Berks, RG41 2EY, UK http://www.actcrystals.com Issue : 1.1 C1 Date : March 2010 Tel : +44 118 979 1238 Fax : +44 118 979 1283 Email: [email protected] 4.Typical Frequency Response In keeping with our ongoing policy of product evolvement and improvement, the above specification is subject to change without notice. ISO9001: 2000 Registered For quotations or further information please contact us at: 3 The Business Centre, Molly Millars Lane, Wokingham, Berks, RG41 2EY, UK http://www.actcrystals.com Issue : 1.1 C1 Date : March 2010 Tel : +44 118 979 1238 Fax : +44 118 979 1283 Email: [email protected] 5.Performance 5-1.Maximum Ratings (Ta=25°C) Item Conditions Rating Unit Between input or output 0 V Between any two electrodes 3 V 50/60 Hz, Between input or output 3 Vp-p DC Voltage Instantaneous DC Voltage AC Voltage Storage temperature range Tstg — -55 to +85 °C Tstg Operating temperature range Topr — -20 to +70 °C Topr 5-2.Electronic Characteristics TA = 25 °C Reference temperature: Terminating source impedance: ZS = 50 Ω Terminating load impedance: ZL = 50 Ω Item Centre Frequency fc Insertion attenuation 479.50 MHz (Reference level for the following data) Pass bandwidth αrel≤3dB Relative attenuation α B3dB Min. Typ. Max. Unit -- 479.50 -- MHz -- 23.3 25.3 dB -- 16.5 -- MHz --4.5 -9.0 -- -46 -2.5 -5.9 -42 -30 ---30 dB dB dB dB αrel 463.50 MHz 470.50 MHz 488.50 MHz 495.50 MHz Amplitude ripple (p-p) 474.50 … 484.50 MHz Δα -- 0.5 1.0 dB Group delay ripple (p-p) 474.50 … 484.50 MHz Δτ -- 12 25 ns(p-p) -- -18 -25 ppm/K Temperature coefficient of frequency TCf In keeping with our ongoing policy of product evolvement and improvement, the above specification is subject to change without notice. ISO9001: 2000 Registered For quotations or further information please contact us at: 3 The Business Centre, Molly Millars Lane, Wokingham, Berks, RG41 2EY, UK http://www.actcrystals.com Issue : 1.1 C1 Date : March 2010 Tel : +44 118 979 1238 Fax : +44 118 979 1283 Email: [email protected] 6.Reliability Test 6.1 Life Test Item Test Condition High Temperature Exposure Limit Tstg Max.(85°C),500h Topr Max.( 70°C),DC 0.5V Δfo≤±0.5% (In or Out),500h (Δfo: Deviation of centre Low Temperature Exposure Tstg Min.( -55°C),500h frequency fo) Moisture Resistance Ta=60°C,RH=90%,500H High Temperature Operation 6.2 Environmental Test Item Test Condition (-20°C 30min. → 25°C 5min. → 80°C TCT 30min. →25°C 5min.), 5cycles Immerse the pins in melt solder at 230±5 Soldering °C for 5 seconds. Heat Resistivity for Set on PC board, immerse in melt solder Melt Solder at 260±5°C for 6±2 seconds. Limit Same as 6.1 More than 95% of total area of the pins should be covered with solder Same as 6.1 6.3 Mechanical Test Item Test Condition Drop On maple plate from 1m high,3times. Lead Bend π / 2 rad bending, with 4.4N weight,2 times. Lead Pull Limit Same as 6.1 After bending lead parallel to heater base, pull with 9.8N force for 1 minute. In keeping with our ongoing policy of product evolvement and improvement, the above specification is subject to change without notice. ISO9001: 2000 Registered For quotations or further information please contact us at: 3 The Business Centre, Molly Millars Lane, Wokingham, Berks, RG41 2EY, UK http://www.actcrystals.com Issue : 1.1 C1 Date : March 2010 Tel : +44 118 979 1238 Fax : +44 118 979 1283 Email: [email protected] iCAUTION: Electrostatic Sensitive Device. Observe precautions for handling! 1. 2. 3. 4. 5. 6. The frequency f C is defined as the midpoint between the 3dB frequencies. Unless noted otherwise, all measurements are made with the filter installed in the specified test fixture that is connected to a 50Ω test system with VSWR≤1.2:1. The test fixture L and C are adjusted for minimum insertion loss at the filter centre frequency, f C. Note that insertion loss, bandwidth, and passband shape are dependent on the impedance matching component values and quality. Unless noted otherwise, specifications apply over the entire specified operating temperature range. The specifications of this device are based on the test circuit shown above and subject to change or obsolescence without notice. All equipment designs utilizing this product must be approved by the appropriate government agency prior to manufacture or sale. Our liability is only assumed for the Surface Acoustic Wave (SAW) component(s) per se, not for applications, processes and circuits implemented within components or assemblies. In keeping with our ongoing policy of product evolvement and improvement, the above specification is subject to change without notice. ISO9001: 2000 Registered For quotations or further information please contact us at: 3 The Business Centre, Molly Millars Lane, Wokingham, Berks, RG41 2EY, UK http://www.actcrystals.com Issue : 1.1 C1 Date : March 2010