TI1 ADC08832IMX 8-bit serial i/o cmos a/d converters with multiplexer and sample/hold function Datasheet

ADC08831, ADC08832
www.ti.com
SNAS015C – SEPTEMBER 1999 – REVISED MARCH 2013
ADC08831 /ADC08832 8-Bit Serial I/O CMOS A/D Converters with Multiplexer and
Sample/Hold Function
Check for Samples: ADC08831, ADC08832
FEATURES
DESCRIPTION
•
The ADC08831/ADC08832 are 8-bit successive
approximation Analog to Digital converters with 3-wire
serial interfaces and a configurable input multiplexer
for 2 channels. The serial I/O will interface to
COPSfamily
of
micro-controllers,
PLD's,
microprocessors, DSP's, or shift registers. The serial
I/O is configured to comply with the MICROWIRE
serial data exchange standard.
1
2
•
•
•
•
•
•
3-Wire Serial Digital Data Link Requires Few
I/O Pins
Analog Input Track/Hold Function
2-Channel Input Multiplexer Option with
Address Logic
Analog Input Voltage Range from GND to VCC
No Zero or Full Scale Adjustment Required
TTL/CMOS Input/Output Compatible
Superior Pin Compatible Replacement for
ADC0831/2
APPLICATIONS
•
•
•
•
•
Digitizing Sensors and Waveforms
Process Control Monitoring
Remote Sensing in Noisy Environments
Instrumentation
Embedded Systems
To minimize total power consumption, the
ADC08831/ADC08832 automatically go into low
power mode whenever they are not performing
conversions.
A track/hold function allows the analog voltage at the
positive input to vary during the actual A/D
conversion.
The analog inputs can be configured to operate in
various combinations of single-ended, differential, or
pseudo-differential modes. The voltage reference
input can be adjusted to allow encoding of small
analog voltage spans to the full 8-bits of resolution.
KEY SPECIFICATIONS
•
•
•
•
•
•
•
Resolution: 8 Bits
Conversion Time (fC = 2 MHz): 4μs (Max)
Power Dissipation: 8.5mW (Typ)
Low Power Mode: 3.0mW (Typ)
Single Supply: 5VDC
Total Unadjusted Error: ±1LSB
No Missing Codes over Temperature
Typical Application
1
2
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
All trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 1999–2013, Texas Instruments Incorporated
ADC08831, ADC08832
SNAS015C – SEPTEMBER 1999 – REVISED MARCH 2013
www.ti.com
Connection Diagram
xxx
Figure 1. ADC08831
8-Lead SOIC or VSSOP
See D or DGK Packages
Figure 2. ADC08832
8-Lead SOIC or VSSOP
See D or DGK Packages
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
Absolute Maximum Ratings (1) (2) (3)
Supply Voltage (VCC)
6.5V
−0.3V to VCC + 0.3V
Voltage at Inputs and Outputs
Input Current at Any Pin (4)
±5 mA
Package Input Current (4)
ESD Susceptibility (5)
±20 mA
Human Body Model
2000V
Machine Model
200V
Junction Temperature (6)
150°C
−65° C to 150°C
Storage Temperature Range
Mounting Temperature
(1)
(2)
(3)
(4)
(5)
(6)
Lead Temp. (soldering, 10 sec)
260°C
Infrared (10 sec)
215°C
All voltages are measured with respect to GND = 0 VDC, unless otherwise specified.
Absolute Maximum Ratings indicate limits beyond which damage to the device may occur.
If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/ Distributors for availability and
specifications.
When the input voltage VIN at any pin exceeds the power supplies (VIN < (GND) or VIN > VCC,) the current at that pin should be limited
to 5 mA. The 20 mA maximum package input current rating limits the number of pins that can safely exceed the power supplies with an
input current of 5 mA to four pins.
Human body model, 100 pF capacitor discharged through a 1.5 kΩ resistor. The machine mode is a 200pF capacitor discharged directly
into each pin.
The maximum power dissipation must be derated at elevated temperatures and is dictated by TJMAX, θJA and the ambient temperature,
TA. The maximum allowable power dissipation at any temperature is PD = (TJMAX − TA)/θJA or the number given in the Absolute
Maximum Ratings, whichever is lower.
Operating Ratings (1) (2)
−40°C ≤ TJ ≤ +85°C
Temperature Range
Supply Voltage
Thermal Resistance (θjA)
4.5 V to 6.0 V
VSSOP, 8-pin Surface Mount
122°C/W
SOIC Package, 8-pin Surface Mount
235°C/W
10kHz ≤ fCLK ≤ 2MHz
Clock Frequency
(1)
(2)
2
Operating Ratings indicate conditions for which the device is functional. These ratings do not specify specific performance limits. For
specifications and test conditions, see the Electrical Characteristics. The specifications apply only for the test conditions listed. Some
performance characteristics may degrade when the device is not operated under the listed test conditions.
All voltages are measured with respect to GND = 0 VDC, unless otherwise specified.
Submit Documentation Feedback
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: ADC08831 ADC08832
ADC08831, ADC08832
www.ti.com
SNAS015C – SEPTEMBER 1999 – REVISED MARCH 2013
Electrical Characteristics
The following specifications apply for VCC = VREF = +5VDC, and fCLK = 2 MHz unless otherwise specified. Boldface limits
apply for TA = TJ = TMIN to TMAX; all other limits TA = TJ = 25°C.
Symbol
Parameter
Conditions
Typical (1)
Limits (2)
Units (Limits)
±0.3
±1
LSB
(max)
CONVERTER AND MULTIPLEXER CHARACTERISTICS
TUE
See (3)
Total Unadjusted Error
Offset Error
±0.2
LSB
DNL
Differential NonLinearity
±0.2
LSB
INL
Integral NonLinearity
±0.2
LSB
FS
Full Scale Error
±0.3
RREF
Reference Input Resistance
See (4)
VIN
Analog Input Voltage
See (5)
3.5
DC Common-Mode Error
LSB
2.8
5.9
kΩ (min)
kΩ (max)
(VCC + 0.05)
(GND − 0.05)
V (max)
V (min)
±¼
LSB (max)
Power Supply Sensitivity
VCC = 5V ±10%,
VCC = 5V ±5%
±¼
±¼
LSB (max)
LSB (max)
On Channel Leakage Current (6)
On Channel = 5V,
Off Channel = 0V
0.2
1
μA (max)
On Channel = 0V
Off Channel = 5V
−0.2
−1
μA (min)
On Channel = 5V, Off
Channel = 0V
−0.2
−1
μA (min)
On Channel = 0V,
Off Channel = 5V
0.2
1
μA (max)
Off Channel Leakage Current (7)
DC CHARACTERISTICS
VIN(1)
Logical “1” Input Voltage
2.0
V (min)
VIN(0)
Logical “0” Input Voltage
0.8
V (max)
IIN(1)
Logical “1” Input Current
VIN = 5.0V
0.05
+1
μA (max)
IIN(0)
Logical “0” Input Current
VIN = 0V
0.05
−1
μA (max)
VOUT(1)
Logical “1” Output Voltage
VCC = 4.75V:
IOUT = −360 μA
2.4
V (min)
IOUT = −10 μA
4.5
V (min)
VCC = 4.75V
IOUT = 1.6 mA
0.4
V (max)
VOUT(0)
(1)
(2)
(3)
(4)
(5)
(6)
(7)
Logical “0” Output Voltage
Typicals are at TJ = 25°C and represent the most likely parametric norm.
Specified to TI's AOQL (Average Outgoing Quality Level).
Total Unadjusted Error (TUE) includes offset, full-scale, linearity, multiplexer errors.
It is not tested for the ADC08832.
For VIN(−) ≥ VIN(+) the digital code will be 0000 0000. Two on-chip diodes are tied to each analog input (see ADC08832 Functional Block
Diagram) which will forward-conduct for analog input voltages one diode drop below ground or one diode drop greater than VCC supply.
During testing at low VCC levels (e.g., 4.5V), high level analog inputs (e.g., 5V) can cause an input diode to conduct, especially at
elevated temperatures, which will cause errors for analog inputs near full-scale. The spec allows 50 mV forward bias of either diode; this
means that as long as the analog VIN does not exceed the supply voltage by more than 50 mV, the output code will be correct.
Exceeding this range on an unselected channel will corrupt the reading of a selected channel. Achievement of an absolute 0 VDC to 5
VDC input voltage range will therefore require a minimum supply voltage of 4.950 VDC over temperature variations, initial tolerance and
loading.
Channel leakage current is measured after a single-ended channel is selected and the clock is turned off. For off channel leakage
current the following two cases are considered: one, with the selected channel tied high (5 VDC) and the remaining off channel tied low
(0 VDC), total current flow through the off channel is measured; two, with the selected channel tied low and the off channels tied high,
total current flow through the off channel is again measured. The two cases considered for determining on channel leakage current are
the same except total current flow through the selected channel is measured.
Channel leakage current is measured after a single-ended channel is selected and the clock is turned off. For off channel leakage
current the following two cases are considered: one, with the selected channel tied high (5 VDC) and the remaining off channel tied low
(0 VDC), total current flow through the off channel is measured; two, with the selected channel tied low and the off channels tied high,
total current flow through the off channel is again measured. The two cases considered for determining on channel leakage current are
the same except total current flow through the selected channel is measured.
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: ADC08831 ADC08832
Submit Documentation Feedback
3
ADC08831, ADC08832
SNAS015C – SEPTEMBER 1999 – REVISED MARCH 2013
www.ti.com
Electrical Characteristics (continued)
The following specifications apply for VCC = VREF = +5VDC, and fCLK = 2 MHz unless otherwise specified. Boldface limits
apply for TA = TJ = TMIN to TMAX; all other limits TA = TJ = 25°C.
Symbol
Parameter
Conditions
Typical (1)
Limits (2)
Units (Limits)
IOUT
TRI-STATE Output Current
VOUT = 0V
VOUT = 5V
−3.0
3.0
μA (max)
μA (max)
ISOURCE
Output Source Current
VOUT = 0V
−6.5
mA (max)
ISINK
Output Sink Current
VOUT = VCC
8.0
mA (min)
ICC
Supply Current ADC08831 CLK = VCC CS = VCC
0.6
1.0
mA (max)
CS = LOW
1.7
2.4
mA (max)
ICC
Supply Current ADC08832 CLK =
VCC (8)
CS = VCC
1.3
1.8
mA (max)
CS = LOW
2.4
3.5
mA (max)
(8)
For the ADC08832 Vref is internally tied to VCC, therefore, for the ADC08832 reference current is included in the supply current.
Electrical Characteristics
The following specifications apply for VCC = VREF = +5 VDC, and tr = tf = 20 ns unless otherwise specified. Boldface limits
apply for TA = TJ = TMIN to TMAX; all other limits TA = TJ = 25°C.
Symbol
fCLK
Parameter
Typical (1)
Conditions
Clock Frequency
Clock Duty Cycle
(3)
fCLK = 2MHz
Limits (2)
Units (Limits)
2
MHz (max)
40
60
% (min)
% (max)
8
4
1/fCLK (max)
μs (max)
TC
Conversion Time (Not Including MUX
Addressing Time)
tCA
Acquisition Time
½
1/fCLK (max)
tSET-UP
CS Falling Edge or Data Input
Valid to CLK Rising Edge
25
ns (min)
tHOLD
Data Input Valid after CLK
Rising Edge
20
ns (min)
tpd1, tpd0
CLK Falling Edge to Output Data Valid (4)
250
200
ns (max)
ns (max)
CL = 100 pF:
Data MSB First
Data LSB First
t1H, t0H
TRI-STATE Delay from Rising Edge
of CS to Data Output and SARS Hi-Z
CL = 10 pF, RL = 10 kΩ
(see TRI-STATE Test Circuits and
Waveforms)
50
CIN
Capacitance of Analog Input (5)
13
pF
CIN
Capacitance of Logic Inputs
5
pF
COUT
Capacitance of Logic Outputs
5
pF
CL = 100 pF, RL = 2 kΩ
(1)
(2)
(3)
(4)
(5)
4
ns
180
ns (max)
Typicals are at TJ = 25°C and represent the most likely parametric norm.
Specified to TI's AOQL (Average Outgoing Quality Level).
A 40% to 60% duty cycle range insures proper operation at all clock frequencies. In the case that an available clock has a duty cycle
outside of these limits the minimum time the clock is high or low must be at least 250 ns. The maximum time the clock can be high or
low is 60 μs.
Since data, MSB first, is the output of the comparator used in the successive approximation loop, an additional delay is built in to allow
for comparator response time.
Analog inputs are typically 300 ohms input resistance to a 13pF sample and hold capacitor.
Submit Documentation Feedback
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: ADC08831 ADC08832
ADC08831, ADC08832
www.ti.com
SNAS015C – SEPTEMBER 1999 – REVISED MARCH 2013
Dynamic Characteristics
The following specifications apply for VCC = 5V, fCLK = 2MHz, TA= 25°C, RSOURCE = 50Ω, fIN = 45kHz, VIN = 5VP, VREF = 5V,
non-coherent 2048 samples with windowing.
Symbol
Parameter
Conditions
ADC08831
ADC08832
Typical (1)
Units (Limits)
181
153
ksps
ksps
fS
Sampling Rate
SNR
Signal-to -Noise Ratio (4)
48.5
dB
THD
Total Harmonic Distortion (5)
−59.5
dB
SINAD
Signal-to -Noise and Distortion
48.0
dB
7.7
Bits
62.5
dB
(6)
ENOB
Effective Number Of Bits
SFDR
Spurious Free Dynamic Range
(1)
(2)
(3)
(4)
(5)
(6)
fCLK/11
fCLK/13 (3)
Limits (2)
Typicals are at TJ = 25°C and represent the most likely parametric norm.
Specified to TI's AOQL (Average Outgoing Quality Level).
The maximum sampling rate is slightly less than fCLK/11 if CS is reset in less than one clock period.
The signal-to-noise ratio is the ratio of the signal amplitude to the background noise level. Harmonics of the input signal are not included
in it's calculation.
The contributions from the first 6 harmonics are used in the calculation of the THD.
Effective Number Of Bits (ENOB) is calculated from the measured signal-to-noise plus distortion ratio (SINAD) using the equation ENOB
= (SINAD-1.76)/6.02.
Block Diagram
*For ADC08831 VREF pin is available, for ADC08832 DI pin is available, and VREF is tied to VCC
Pin names in parentheses refer to ADC08832
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: ADC08831 ADC08832
Submit Documentation Feedback
5
ADC08831, ADC08832
SNAS015C – SEPTEMBER 1999 – REVISED MARCH 2013
www.ti.com
Typical Performance Characteristics
The following specifications apply for TA = 25°C, VCC = VREF = 5V, unless otherwise specified.
6
Linearity Error (TUE) vs
Reference Voltage
Linearity Error (TUE) vs
Temperature
Figure 3.
Figure 4.
Linearity Error (TUE) vs
Clock Frequency
Power Supply Current vs
Temperature (ADC08831)
Figure 5.
Figure 6.
Power Supply Current vs
Temperature (ADC08832)
Power Supply Current
vs Clock Frequency, CS = Low, ADC08831
Figure 7.
Figure 8.
Submit Documentation Feedback
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: ADC08831 ADC08832
ADC08831, ADC08832
www.ti.com
SNAS015C – SEPTEMBER 1999 – REVISED MARCH 2013
Typical Performance Characteristics (continued)
The following specifications apply for TA = 25°C, VCC = VREF = 5V, unless otherwise specified.
Output Current
vs
Temperature
Spectral Response with 10KHz Sine Wave Input
Figure 9.
Figure 10.
Spectral Response with 55 KHz Sine Wave Input
Spectral Response with 90 KHz Sine Wave Input
Figure 11.
Figure 12.
Total Unadjuster Error Plot
Figure 13.
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: ADC08831 ADC08832
Submit Documentation Feedback
7
ADC08831, ADC08832
SNAS015C – SEPTEMBER 1999 – REVISED MARCH 2013
www.ti.com
Leakage Current Test Circuit
Figure 14.
TRI-STATE Test Circuits and Waveforms
Figure 15.
8
Submit Documentation Feedback
Figure 16.
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: ADC08831 ADC08832
ADC08831, ADC08832
www.ti.com
SNAS015C – SEPTEMBER 1999 – REVISED MARCH 2013
Timing Diagrams
Figure 17. Data Input Timing
Figure 18. Data Output Timing
Figure 19. ADC08831 Start Conversion Timing
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: ADC08831 ADC08832
Submit Documentation Feedback
9
ADC08831, ADC08832
SNAS015C – SEPTEMBER 1999 – REVISED MARCH 2013
www.ti.com
*LSB first output not available on ADC08831.
Figure 20. ADC08831 Timing
Figure 21. ADC08832 Timing
10
Submit Documentation Feedback
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: ADC08831 ADC08832
ADC08831, ADC08832
www.ti.com
SNAS015C – SEPTEMBER 1999 – REVISED MARCH 2013
ADC08832 Functional Block Diagram
*Some of these functions/pins are not available with other options.
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: ADC08831 ADC08832
Submit Documentation Feedback
11
ADC08831, ADC08832
SNAS015C – SEPTEMBER 1999 – REVISED MARCH 2013
www.ti.com
FUNCTIONAL DESCRIPTION
MULTIPLEXER ADDRESSING
The design of these converters utilizes a comparator structure with built-in sample-and-hold which provides for a
differential analog input to be converted by a successive approximation routine.
The actual voltage converted is always the difference between an assigned “+” input terminal and a “−” input
terminal. The polarity of each input terminal of the pair indicates which line the converter expects to be the most
positive. If the assigned “+” input voltage is less than the “−” input voltage the converter responds with an all
zeros output code.
A unique input multiplexing scheme has been utilized to provide multiple analog channels with softwareconfigurable single-ended, or differential operation. The analog signal conditioning required in transducer-based
data acquisition systems is significantly simplified with this type of input flexibility. One converter package can
now handle ground referenced inputs, differential inputs, as well as signals with some arbitrary reference voltage.
A particular input configuration is assigned during the MUX addressing sequence, prior to the start of a
conversion. The MUX address selects which of the analog inputs are to be enabled and whether this input is
single-ended or differential. In addition to selecting differential mode the polarity may also be selected. Channel 0
may be selected as the positive input and channel 1 as the negative input or vice versa. This programmability is
illustrated by the MUX addressing codes for the ADC08832.
The MUX address is shifted into the converter via the DI line. Because the ADC08831 contains only one
differential input channel with a fixed polarity assignment, it does not require addressing.
Table 1. Multiplexer/Package Options
Part Number
Number of Analog Channels
Number of Package Pins
Single-Ended
Differential
ADC08831
1
1
8 or 14
ADC08832
2
1
8 or 14
Table 2. MUX Addressing: ADC08832
Single-Ended MUX Mode
MUX Address
Channel #
Start Bit
SGL/DIF
ODD/SIGN
0
1
1
0
+
1
1
1
1
+
Differential MUX Mode
MUX Address
Start Bit
Channel #
SGL/DIF
ODD/SIGN
0
1
1
0
0
+
−
1
0
1
−
+
Since the input configuration is under software control, it can be modified as required before each conversion. A
channel can be treated as a single-ended, ground referenced input for one conversion; then it can be
reconfigured as part of a differential channel for another conversion.
The analog input voltages for each channel can range from 50mV below ground to 50mV above VCC (typically
5V) without degrading conversion accuracy.
THE DIGITAL INTERFACE
A most important characteristic of these converters is their serial data link with the controlling processor. Using a
serial communication format offers two very significant system improvements. It allows many functions to be
included in a small package and it can eliminate the transmission of low level analog signals by locating the
converter right at the analog sensor; transmitting highly noise immune digital data back to the host processor.
12
Submit Documentation Feedback
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: ADC08831 ADC08832
ADC08831, ADC08832
www.ti.com
SNAS015C – SEPTEMBER 1999 – REVISED MARCH 2013
To understand the operation of these converters it is best to refer to Timing Diagrams and ADC08832 Functional
Block Diagram and to follow a complete conversion sequence. For clarity, a separate timing diagram is shown for
each device.
1. A conversion is initiated by pulling the CS (chip select) line low. This line must be held low for the entire
conversion. The converter is now waiting for a start bit and its MUX assignment word, if applicable.
2. On each rising edge of the clock the status of the data in (DI) line is clocked into the MUX address shift
register. The start bit is the first logic “1” that appears on this line (all leading zeros are ignored). Following
the start bit the converter expects the next 2 bits to be the MUX assignment word.
3. When the start bit has been shifted into the start location of the MUX register, and the input channel has
been assigned, a conversion is about to begin. An interval of ½ clock period (where nothing happens) is
automatically inserted to allow the selected MUX channel to settle to a final analog input value. The DI line is
disabled at this time. It no longer accepts data.
4. The data out (DO) line now comes out of TRI-STATE and provides a leading zero for this one clock period of
MUX settling time.
5. During the conversion the output of the SAR comparator indicates whether the analog input is greater than
(high) or less than (low) a series of successive voltages generated internally from a ratioed capacitor array
(first 5 bits) and a resistor ladder (last 3 bits). After each comparison the comparator's output is shipped to
the DO line on the falling edge of CLK. This data is the result of the conversion being shifted out (with the
MSB first) and can be read by the processor immediately.
6. After 8 clock periods the conversion is completed.
7. The stored data in the successive approximation register is loaded into an internal shift register. The data,
LSB first, is automatically shifted out the DO line after the MSB first data stream. The DO line then goes low
and stays low until CS is returned high. The ADC08831 is an exception in that its data is only output in MSB
first format.
8. The DI and DO lines can be tied together and controlled through a bidirectional processor I/O bit with one
wire. This is possible because the DI input is only “looked-at” during the MUX addressing interval while the
DO line is still in a high impedance state.
Reducing Power Consumption
The ADC08831 operate up to a 2MHz clock frequency, or about 181 ksps. At 5V supply, it consumes about 1.7
mA or 8.5 mW when CS is logic low. The ADC08831 has a low power mode to minimize total power
consumption.
When the chip select is asserted with a logic high, some analog circuitry and digital logic are pulled to a static,
low power condition. Also, DOUT, the output driver is taken into TRI-STATE mode.
To optimize static power consumption, special attention is needed to the digital input logic signals: CLK, CS, DI.
Each digital input has a large CMOS buffer between VCC and GND. A traditional TTL level high (2.4V) will be
sufficient for each input to read a logical “1”. However, there could be a large VIH to VCC voltage difference at
each input. Such a voltage difference would cause static power dissipation, even when chip select pin is high
and the part is in low power mode.
Therefore, to minimize static power dissipation, it is recommended that all digital input logic levels should equal
the converter's supply. Various CMOS logic is particularly well suited for this application.
The reference pin on the ADC08831 is not affected by the power-down mode. To reduce static reference current
during non-conversion time, there are a couple options. First, a low voltage external reference (ie, 2.5V could be
used). A shunt reference, such as the LM385-2.5, could be powered by a logic gate that is the inverse of the
signal on CS. When CS is high, the reference is off. As a second option, an external, low on-resistance switch
could be used.
The ADC08832 is similar to the ADC08831, except its reference is derived from VCC. The ADC08832 does enter
a low-power mode when CS is logic high, as the analog and digital logic enter static current modes. However
power dissipation from the reference ladder occurs, regardless of the signal on CS
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: ADC08831 ADC08832
Submit Documentation Feedback
13
ADC08831, ADC08832
SNAS015C – SEPTEMBER 1999 – REVISED MARCH 2013
www.ti.com
REFERENCE CONSIDERATIONS
The voltage applied to the reference input on these converters, VREF, defines the voltage span of the analog
input (the difference between VIN(MAX) and VIN(MIN) over which the 256 possible output codes apply. The devices
can be used either in ratiometric applications or in systems requiring absolute accuracy. The reference pin must
be connected to a voltage source capable of driving the reference input resistance which can be as low as
2.8kΩ. This pin is the top of a resistor divider string and capacitor array used for the successive approximation
conversion.
In a ratiometric system the analog input voltage is proportional to the voltage used for the A/D reference. This
voltage is typically the system power supply, so the VREF pin can be tied to VCC (done internally on the
ADC08832). This technique relaxes the stability requirements of the system reference as the analog input and
A/D reference move together maintaining the same output code for a given input condition.
For absolute accuracy, where the analog input varies between very specific voltage limits, the reference pin can
be biased with a time and temperature stable voltage source. The LM385, LM336 and LM4040 reference diodes
are good low current devices to use with these converters.
The maximum value of the reference is limited to the VCC supply voltage. The minimum value, however, can be
quite small (see Typical Performance Characteristics) to allow direct conversions of transducer outputs providing
less than a 5V output span. Particular care must be taken with regard to noise pickup, circuit layout and system
error voltage sources when operating with a reduced span due to the increased sensitivity of the converter (1
LSB equals VREF/256).
Left) Ratiometric
Right) Absolute with a Reduced Span
Figure 22. Reference Examples
THE ANALOG INPUTS
The most important feature of these converters is that they can be located right at the analog signal source and
through just a few wires can communicate with a controlling processor with a highly noise immune serial bit
stream. This in itself greatly minimizes circuitry to maintain analog signal accuracy which otherwise is most
susceptible to noise pickup. However, a few words are in order with regard to the analog inputs should the input
be noisy to begin with or possibly riding on a large common-mode voltage.
14
Submit Documentation Feedback
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: ADC08831 ADC08832
ADC08831, ADC08832
www.ti.com
SNAS015C – SEPTEMBER 1999 – REVISED MARCH 2013
The differential input of these converters actually reduces the effects of common-mode input noise, a signal
common to both selected “+” and “−” inputs for a conversion (60 Hz is most typical). The time interval between
sampling the “+” input and then the “−” input is ½ of a clock period. The change in the common-mode voltage
during this short time interval can cause conversion errors. For a sinusoidal common-mode signal this error is:
where
•
•
•
where fCM is the frequency of the common-mode signal
VPEAK is its peak voltage value
fCLK is the A/D clock frequency
(1)
For a 60Hz common-mode signal to generate a ¼ LSB error (≊5mV) with the converter running at 250kHz, its
peak value would have to be 6.63V which would be larger than allowed as it exceeds the maximum analog input
limits.
Source resistance limitation is important with regard to the DC leakage currents of the input multiplexer. Bypass
capacitors should not be used if the source resistance is greater than 1kΩ. The worst-case leakage current of
±1μA over temperature will create a 1mV input error with a 1kΩ source resistance. An op amp RC active low
pass filter can provide both impedance buffering and noise filtering should a high impedance signal source be
required.
Sample and Hold
The ADC08831/2 provide a built-in sample-and-hold to acquire the input signal. The sample and hold can sample
input signals in either single-ended or pseudo differential mode.
Input Op Amps
When driving the analog inputs with an op amp it is important that the op amp settle within the allowed time. To
achieve the full sampling rate, the analog input should be driven with a low impedance source (100Ω) or a highspeed op amp such as the LM6142. Higher impedance sources or slower op amps can easily be accommodated
by allowing more time for the analog input to settle.
Source Resistance
The analog inputs of the ADC08831/2 look like a 13pF capacitor (CIN) in series with 300Ω resistor (Ron). CIN gets
switched between the selected “+” and “−” inputs during each conversion cycle. Large external source resistors
will slow the settling of the inputs. It is important that the overall RC time constants be short enough to allow the
analog input to completely settle.
Board Layout Consideration, Grounding and Bypassing:
The ADC08831/2 are easy to use with some board layout consideration. They should be used with an analog
ground plane and single-point grounding techniques. The GND pin should be tied directly to the ground plane.
The supply pin should be bypassed to the ground plane with a surface mount or ceramic capacitor with leads as
short as possible. All analog inputs should be referenced directly to the single-point ground. Digital inputs and
outputs should be shielded from and routed away from the reference and analog circuitry.
OPTIONAL ADJUSTMENTS
Zero Error
The offset of the A/D does not require adjustment. If the minimum analog input voltage value, VIN(MIN), is not
ground a zero offset can be done. The converter can be made to output 0000 0000 digital code for this minimum
input voltage by biasing any VIN (−) input at this VIN(MIN) value. This utilizes the differential mode operation of the
A/D.
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: ADC08831 ADC08832
Submit Documentation Feedback
15
ADC08831, ADC08832
SNAS015C – SEPTEMBER 1999 – REVISED MARCH 2013
www.ti.com
The zero error of the A/D converter relates to the location of the first riser of the transfer function and can be
measured by grounding the VIN (−) input and applying a small magnitude positive voltage to the VIN (+) input.
Zero error is the difference between the actual DC input voltage which is necessary to just cause an output
digital code transition from 0000 0000 to 0000 0001 and the ideal ½ LSB value (½ LSB = 9.8mV for VREF =
5.000VDC).
Full Scale
The full-scale adjustment can be made by applying a differential input voltage which is 1½ LSB down from the
desired analog full-scale voltage range and then adjusting the magnitude of the VREF input (or VCC for the
ADC08832) for a digital output code which is just changing from 1111 1110 to 1111 1111.
Adjusting for an Arbitrary Analog Input
Voltage Range
If the analog zero voltage of the A/D is shifted away from ground (for example, to accommodate an analog input
signal which does not go to ground), this new zero reference should be properly adjusted first. A VIN (+) voltage
which equals this desired zero reference plus ½ LSB (where the LSB is calculated for the desired analog span,
using 1 LSB = analog span/256) is applied to selected “+” input and the zero reference voltage at the
corresponding “−” input should then be adjusted to just obtain the 00HEX to 01HEX code transition.
The full-scale adjustment should be made [with the proper VIN (−) voltage applied] by forcing a voltage to the VIN
(+) input which is given by:
where
•
•
•
VMAX = the high end of the analog input range
VMIN = the low end (the offset zero) of the analog range
(Both are ground referenced.)
(2)
The VREFIN (or VCC) voltage is then adjusted to provide a code change from FEHEX to FFHEX. This completes the
adjustment procedure.
DYNAMIC PERFORMANCE
Dynamic performance specifications are often useful in applications requiring waveform sampling and digitization.
Typically, a memory buffer is used to capture a stream of consecutive digital outputs for post processing.
Capturing a number of samples that is a power of 2 (ie, 1024, 2048, 4096) allows the Fast Fourier Transform
(FFT) to be used to digitally analyze the frequency components of the signal. Depending on the application,
further digital filtering, windowing, or processing can be applied.
Sampling Rate
The Sampling Rate, sometimes referred to as the Throughput Rate, is the time between repetitive samples by an
Analog-to-Digital Converter. The sampling rate includes the conversion time, as well as other factors such a MUX
setup time, acquisition time, and interfacing time delays. Typically, the sampling rate is specified in the number of
samples taken per second, at the maximum Analog-to-Digital Converter clock frequency.
Signals with frequencies exceeding the Nyquist frequency (1/2 the sampling rate), will be aliased into frequencies
below the Nyquist frequency. To prevent signal degradation, sample at twice (or more) than the input signal
and/or use of a low pass (anti-aliasing) filter on the front-end. Sampling at a much higher rate than the input
signal will reduce the requirements of the anti-aliasing filter.
Some applications require under-sampling the input signal. In this case, one expects the fundamental to be
aliased into the frequency range below the Nyquist frequency. In order to be assured the frequency response
accurately represents a harmonic of the fundamental, a band-pass filter should be used over the input range of
interest.
16
Submit Documentation Feedback
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: ADC08831 ADC08832
ADC08831, ADC08832
www.ti.com
SNAS015C – SEPTEMBER 1999 – REVISED MARCH 2013
Signal-to-Noise Ratio
Signal-to-Noise Ratio (SNR) is the ratio of RMS magnitude of the fundamental to the RMS sum of all the nonfundamental signal, excluding the harmonics, up to 1/2 of the sampling frequency (Nyquist).
Total Harmonic Distortion
Total Harmonic distortion is the ratio of the RMS sum of the amplitude of the harmonics to the fundamental input
frequency.
THD = 20 log [(V22 + V32+ V42+ V52+ V62) 1/2/V1]
where
•
•
V1 is the RMS amplitude of the fundamental
V2,V3, V4, V5, V6 are the RMS amplitudes of the individual harmonics.
(3)
In theory, all harmonics are included in THD calculations, but in practice only about the first 6 make significant
contributions and require measurement.
For under-sampling applications, the input signal should be band pass filtered (BPF) to prevent out of band
signals, or their harmonics, to appear in the spectral response.
The DC Linearity transfer function of an Analog-to-Digital Converter tends to influence the dominant harmonics.
A parabolic Linearity curve would tend to create 2nd (and even) order harmonics, while an S-curve would tend to
create 3rd (or odd) order harmonics. The magnitude of an DC linearity error correlates to the magnitude of the
harmonics.
Signal-to-Noise and Distortion
Signal-to-Noise And Distortion ratio (SINAD) is the ratio of RMS magnitude of the fundamental to the RMS sum
of all the non-fundamental signals, including the noise and harmonics, up to 1/2 of the sampling frequency
(Nyquist), excluding DC.
SINAD is also dependent on the number of quantization levels in the A/D Converter used in the waveform
sampling process. The more quantization levels, the smaller the quantization noise and theoretical noise
performance. The theoretical SINAD for a N-Bit Analog-to-Digital Converter is given by:
SINAD = (6.02 N + 1.76) dB
Thus, for an 8-bit converter, the ideal SINAD = 49.92 dB
Effective Number of Bits
Effective Number Of Bits (ENOB) is another specification to quantify dynamic performance. The equation for
ENOB is given by:
ENOB = [(SINAD - 1.76)] / 6.02]
The Effective Number Of Bits portrays the cumulative effect of several errors, including quantization, nonlinearities, noise, and distortion.
Spurious Free Dynamic Range
Spurious Free Dynamic Range (SFDR) is the ratio of the signal amplitude to the amplitude of the highest
harmonic or spurious noise component. If the amplitude is at full scale, the specification is simply the reciprocal
of the peak harmonic or spurious noise.
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: ADC08831 ADC08832
Submit Documentation Feedback
17
ADC08831, ADC08832
SNAS015C – SEPTEMBER 1999 – REVISED MARCH 2013
www.ti.com
Applications
Figure 23. Low-Cost Remote Temperature Sensor
*VIN(−) = 0.15 VCC
15% of VCC ≤ VXDR ≤ 85% of VCC
Figure 24. Operating with Ratiometric Transducers
18
Submit Documentation Feedback
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: ADC08831 ADC08832
ADC08831, ADC08832
www.ti.com
SNAS015C – SEPTEMBER 1999 – REVISED MARCH 2013
Span Adjust; 0V ≤ VIN ≤ 3V
Figure 25. Zero-Shift and Span Adjust: 2V≤VIN ≤ 5V
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: ADC08831 ADC08832
Submit Documentation Feedback
19
ADC08831, ADC08832
SNAS015C – SEPTEMBER 1999 – REVISED MARCH 2013
www.ti.com
Diodes are 1N914
Figure 26. Protecting the Input
Uses one more wire than load cell itself
Two mini-DIPs could be mounted inside load cell for digital output transducer
Electronic offset and gain trims relax mechanical specs for gauge factor and offset
Low level cell output is converted immediately for high noise immunity
Figure 27. Digital Load Cell
20
Submit Documentation Feedback
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: ADC08831 ADC08832
ADC08831, ADC08832
www.ti.com
SNAS015C – SEPTEMBER 1999 – REVISED MARCH 2013
All power supplied by loop
1500V isolation at output
Figure 28. 4 mA-20 mA Current Loop Converter
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: ADC08831 ADC08832
Submit Documentation Feedback
21
ADC08831, ADC08832
SNAS015C – SEPTEMBER 1999 – REVISED MARCH 2013
www.ti.com
Figure 29. Isolated Data Converter
Figure 30. A “Stand-Alone” Hook-Up for ADC08832 Evaluation
22
Submit Documentation Feedback
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: ADC08831 ADC08832
ADC08831, ADC08832
www.ti.com
SNAS015C – SEPTEMBER 1999 – REVISED MARCH 2013
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: ADC08831 ADC08832
Submit Documentation Feedback
23
ADC08831, ADC08832
SNAS015C – SEPTEMBER 1999 – REVISED MARCH 2013
www.ti.com
REVISION HISTORY
Changes from Revision B (March 2013) to Revision C
•
24
Page
Changed layout of National Data Sheet to TI format .......................................................................................................... 22
Submit Documentation Feedback
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: ADC08831 ADC08832
PACKAGE OPTION ADDENDUM
www.ti.com
1-Nov-2015
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
ADC08831IM
NRND
SOIC
D
8
95
TBD
Call TI
Call TI
-40 to 85
08831
IM
ADC08831IM/NOPB
ACTIVE
SOIC
D
8
95
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 85
08831
IM
ADC08831IMX/NOPB
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 85
08831
IM
ADC08832IM/NOPB
ACTIVE
SOIC
D
8
95
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 85
08832
IM
ADC08832IMM/NOPB
ACTIVE
VSSOP
DGK
8
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 85
8832
ADC08832IMMX/NOPB
ACTIVE
VSSOP
DGK
8
3500
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 85
8832
ADC08832IMX
NRND
SOIC
D
8
TBD
Call TI
Call TI
-40 to 85
08832
IM
ADC08832IMX/NOPB
ACTIVE
SOIC
D
8
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 85
08832
IM
2500
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
(4)
1-Nov-2015
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
2-Sep-2015
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
ADC08831IMX/NOPB
SOIC
D
8
2500
330.0
12.4
6.5
5.4
2.0
8.0
12.0
Q1
ADC08832IMM/NOPB
VSSOP
DGK
8
1000
178.0
12.4
5.3
3.4
1.4
8.0
12.0
Q1
ADC08832IMMX/NOPB
VSSOP
DGK
8
3500
330.0
12.4
5.3
3.4
1.4
8.0
12.0
Q1
ADC08832IMX/NOPB
SOIC
D
8
2500
330.0
12.4
6.5
5.4
2.0
8.0
12.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
2-Sep-2015
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
ADC08831IMX/NOPB
SOIC
D
8
2500
367.0
367.0
35.0
ADC08832IMM/NOPB
VSSOP
DGK
8
1000
210.0
185.0
35.0
ADC08832IMMX/NOPB
VSSOP
DGK
8
3500
367.0
367.0
35.0
ADC08832IMX/NOPB
SOIC
D
8
2500
367.0
367.0
35.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2015, Texas Instruments Incorporated