Features • Compatible with MCS-51™ Products • 4K Bytes of Reprogrammable Flash Memory • • • • • • • • • – Endurance: 1,000 Write/Erase Cycles 2.7V to 6V Operating Range Fully Static Operation: 0 Hz to 12 MHz Three-Level Program Memory Lock 128 x 8-Bit Internal RAM 32 Programmable I/O Lines Two 16-Bit Timer/Counters Six Interrupt Sources Programmable Serial Channel Low Power Idle and Power Down Modes Description The AT89LV51 is a low-voltage, high-performance CMOS 8-bit microcomputer with 4K bytes of Flash Programmable and Erasable Read Only Memory. The device is manufactured using Atmel’s high density nonvolatile memory technology and is compatible with the industry standard MCS-51™ instruction set and pinout. The on-chip Flash allows the program memory to be reprogrammed in-system or by a conventional nonvolatile memory programmer. By combining a versatile 8-bit CPU with Flash on a monolithic chip, the Atmel AT89LV51 is a powerful microcomputer which provides a highly flexible and cost effective solution to many embedded control applications. The AT89LV51 operates at 2.7 volts up to 6.0 volts. (continued) PDIP Pin Configurations (TXD) (INT0) (INT1) (T0) (T1) 13 15 17 19 21 12 14 16 18 20 22 P0.4 (AD4) P0.5 (AD5) P0.6 (AD6) P0.7 (AD7) EA/VPP NC ALE/PROG PSEN P2.7 (A15) P2.6 (A14) P2.5 (A13) PLCC INDEX CORNER (WR) P3.6 (RD) P3.7 X TA L 2 X TA L 1 GND GND (A8) P2.0 (A9) P2.1 (A10) P2.2 (A11) P2.3 (A12) P2.4 (RXD) 33 32 31 30 29 28 27 26 25 24 23 1 2 3 4 5 6 7 8 9 10 11 VCC P0.0 (AD0) P0.1 (AD1) P0.2 (AD2) P0.3 (AD3) P0.4 (AD4) P0.5 (AD5) P0.6 (AD6) P0.7 (AD7) EA/VPP ALE/PROG PSEN P2.7 (A15) P2.6 (A14) P2.5 (A13) P2.4 (A12) P2.3 (A11) P2.2 (A10) P2.1 (A9) P2.0 (A8) Not Recommended for New Designs. Use AT89LS51. (AD0) (AD1) (AD2) (AD3) 44 42 40 38 36 34 43 41 39 37 35 P1.5 P1.6 P1.7 RST P3.0 NC P3.1 P3.2 P3.3 P3.4 P3.5 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 AT89LV51 (RXD) (TXD) (INT0) (INT1) (T0) (T1) P1.5 P1.6 P1.7 RST P3.0 NC P3.1 P3.2 P3.3 P3.4 P3.5 P1.4 P1.3 P1.2 P1.1 P1.0 NC VCC P0.0 P0.1 P0.2 P0.3 P1.4 P1.3 P1.2 P1.1 P1.0 NC VCC P0.0 P0.1 P0.2 P0.3 INDEX CORNER 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 6 4 2 44 42 40 1 3 4 3 4 13 9 7 5 8 38 9 37 36 10 35 11 34 12 33 13 32 14 31 15 16 30 1 7 1 9 2 1 2 3 2 5 2 72 9 18 20 22 24 26 28 (WR) P3.6 (RD) P3.7 X TA L 2 X TA L 1 GND NC (A8) P2.0 (A9) P2.1 (A10) P2.2 (A11) P2.3 (A12) P2.4 (AD0) (AD1) (AD2) (AD3) TQFP P1.0 P1.1 P1.2 P1.3 P1.4 P1.5 P1.6 P1.7 RST (RXD) P3.0 (TXD) P3.1 (INT0) P3.2 (INT1) P3.3 (T0) P3.4 (T1) P3.5 (WR) P3.6 (RD) P3.7 X TA L 2 X TA L 1 GND 8-Bit Microcontroller with 4K Bytes Flash P0.4 (AD4) P0.5 (AD5) P0.6 (AD6) P0.7 (AD7) EA/VPP NC ALE/PROG PSEN P2.7 (A15) P2.6 (A14) P2.5 (A13) 0303D-D–12/97 4-45 Block Diagram 4-46 Not Not The AT89LV51 provides the following standard features: 4K bytes of Flash, 128 bytes of RAM, 32 I/O lines, two 16bit timer/counters, a five vector two-level interrupt architecture, a full duplex serial port, on-chip oscillator and clock circuitry. In addition, the AT89LV51 is designed with static logic for operation down to zero frequency and supports two software selectable power saving modes. The Idle Mode stops the CPU while allowing the RAM, timer/counters, serial port and interrupt system to continue functioning. The Power Down Mode saves the RAM contents but freezes the oscillator disabling all other chip functions until the next hardware reset. Pin Description VCC Supply voltage. when emitting 1s. During accesses to external data memory that use 8-bit addresses (MOVX @ RI), Port 2 emits the contents of the P2 Special Function Register. Port 2 also receives the high-order address bits and some control signals during Flash programming and verification. Port 3 Port 3 is an 8-bit bidirectional I/O port with internal pullups. The Port 3 output buffers can sink/source four TTL inputs. When 1s are written to Port 3 pins they are pulled high by the internal pullups and can be used as inputs. As inputs, Port 3 pins that are externally being pulled low will source current (IIL) because of the pullups. Port 3 also serves the functions of various special features of the AT89LV51 as listed below: Port Pin Alternate Functions GND Ground. P3.0 RXD (serial input port) P3.1 TXD (serial output port) Port 0 Port 0 is an 8-bit open drain bidirectional I/O port. As an output port each pin can sink eight TTL inputs. When 1s are written to port 0 pins, the pins can be used as highimpedance inputs. Port 0 may also be configured to be the multiplexed loworder address/data bus during accesses to external program and data memory. In this mode P0 has internal pullups. Port 0 also receives the code bytes during Flash programming, and outputs the code bytes during program verification. External pullups are required during program verification. P3.2 INT0 (external interrupt 0) P3.3 INT1 (external interrupt 1) P3.4 T0 (timer 0 external input) P3.5 T1 (timer 1 external input) P3.6 WR (external data memory write strobe) P3.7 RD (external data memory read strobe) Port 1 Port 1 is an 8-bit bidirectional I/O port with internal pullups. The Port 1 output buffers can sink/source four TTL inputs. When 1s are written to Port 1 pins they are pulled high by the internal pullups and can be used as inputs. As inputs, Port 1 pins that are externally being pulled low will source current (IIL) because of the internal pullups. Port 1 also receives the low-order address bytes during Flash programming and verification. Port 2 Port 2 is an 8-bit bidirectional I/O port with internal pullups. The Port 2 output buffers can sink/source four TTL inputs. When 1s are written to Port 2 pins they are pulled high by the internal pullups and can be used as inputs. As inputs, Port 2 pins that are externally being pulled low will source current (IIL) because of the internal pullups. Port 2 emits the high-order address byte during fetches from external program memory and during accesses to external data memory that use 16-bit addresses (MOVX @ DPTR). In this application it uses strong internal pullups Port 3 also receives some control signals for Flash programming and verification. RST Reset input. A high on this pin for two machine cycles while the oscillator is running resets the device. ALE/PROG Address Latch Enable output pulse for latching the low byte of the address during accesses to external memory. This pin is also the program pulse input (PROG) during Flash programming. In normal operation ALE is emitted at a constant rate of 1/6 the oscillator frequency, and may be used for external timing or clocking purposes. Note, however, that one ALE pulse is skipped during each access to external Data Memory. PSEN Program Store Enable is the read strobe to external program memory. When the AT89LV51 is executing code from external program memory, PSEN is activated twice each machine cycle, except that two PSEN activations are skipped during each access to external data memory. 4-47 EA/VPP External Access Enable. EA must be strapped to GND in order to enable the device to fetch code from external program memory locations starting at 0000H up to FFFFH. Note, however, that if lock bit 1 is programmed, EA will be internally latched on reset. EA should be strapped to VCC for internal program executions. This pin also receives the 12-volt programming enable voltage (V PP ) during Flash programming, when 12-volt programming is selected. XTAL1 Input to the inverting oscillator amplifier and input to the internal clock operating circuit. XTAL2 Output from the inverting oscillator amplifier. Special Function Registers A map of the on-chip memory area called the Special Function Register (SFR) space is shown in Table 1. Note that not all of the addresses are occupied, and unoccupied addresses may not be implemented on the chip. Read accesses to these addresses will in general return random data, and write accesses will have an indeterminate effect. User software should not write 1s to these unlisted locations, since they may be used in future products to invoke new features. In that case, the reset or inactive values of the new bits will always be 0. Timer 0 and 1 Timer 0 and Timer 1 in the AT89LV51 operate the same way as Timer 0 and Timer 1 in the AT89C51. Table 1. AT89LV51 SFR Map and Reset Values 0F8H 0F0H 0FFH B 00000000 0F7H 0E8H 0E0H 0EFH ACC 00000000 0E7H 0D8H 0DFH 0D0H PSW 00000000 0C8H T2CON 00000000 0D7H T2MOD XXXXXX00 RCAP2L 00000000 RCAP2H 00000000 TL2 00000000 TH2 00000000 0CFH 0C0H 0C7H 0B8H IP XX000000 0BFH 0B0H P3 11111111 0B7H 0A8H IE 0X000000 0AFH 0A0H P2 11111111 0A7H 98H SCON 00000000 90H P1 11111111 88H TCON 00000000 TMOD 00000000 TL0 00000000 TL1 00000000 80H P0 11111111 SP 00000111 DPL 00000000 DPH 00000000 4-48 SBUF XXXXXXXX 9FH 97H Not TH0 00000000 TH1 00000000 8FH PCON 0XXX0000 87H Not Oscillator Characteristics Figure 1. Oscillator Connections XTAL1 and XTAL2 are the input and output, respectively, of an inverting amplifier which can be configured for use as an on-chip oscillator, as shown in Figure 1. Either a quartz crystal or ceramic resonator may be used. To drive the device from an external clock source, XTAL2 should be left unconnected while XTAL1 is driven as shown in Figure 2. There are no requirements on the duty cycle of the external clock signal, since the input to the internal clocking circuitry is through a divide-by-two flip-flop, but minimum and maximum voltage high and low time specifications must be observed Idle Mode In idle mode, the CPU puts itself to sleep while all the onchip peripherals remain active. The mode is invoked by software. The content of the on-chip RAM and all the special functions registers remain unchanged during this mode. The idle mode can be terminated by any enabled interrupt or by a hardware reset. It should be noted that when idle is terminated by a hardware reset, the device normally resumes program execution, from where it left off, up to two machine cycles before the internal reset algorithm takes control. On-chip hardware inhibits access to internal RAM in this event, but access to the port pins is not inhibited. To eliminate the possibility of an unexpected write to a port pin when Idle is terminated by reset, the instruction following the one that invokes Idle should not be one that writes to a port pin or to external memory. C2 XTAL2 C1 XTAL1 GND Note: C1, C2 = 30 pF ± 10 pF for Crystals = 40 pF ± 10 pF for Ceramic Resonators Figure 2. External Clock Drive Configuration NC XTAL2 EXTERNAL OSCILLATOR SIGNAL XTAL1 GND Power Down Mode In the power down mode the oscillator is stopped, and the instruction that invokes power down is the last instruction executed. The on-chip RAM and Special Function Registers retain their values until the power down mode is terminated. The only exit from power down is a hardware reset. Reset redefines the SFRs but does not change the on-chip RAM. The reset should not be activated before V CC is restored to its normal operating level and must be held active long enough to allow the oscillator to restart and stabilize. Status of External Pins During Idle and Power Down Modes Mode Program Memory ALE PSEN PORT0 PORT1 PORT2 PORT3 Idle Internal 1 1 Data Data Data Data Idle External 1 1 Float Data Address Data Power Down Internal 0 0 Data Data Data Data Power Down External 0 0 Float Data Data Data 4-49 Program Memory Lock Bits On the chip are three lock bits which can be left unprogrammed (U) or can be programmed (P) to obtain the additional features listed in the table below: Lock Bit Protection Modes (1) Program Lock Bits Protection Type LB1 LB2 LB3 1 U U U No program lock features. 2 P U U MOVC instructions executed from external program memory are disabled from fetching code bytes from internal memory, EA is sampled and latched on reset, and further programming of the Flash is disabled. 3 P P U Same as mode 2, also verify is disabled. 4 P P P Same as mode 3, also external execution is disabled. Note: 1. The lock bits can only be erased with the Chip Erase operation. When lock bit 1 is programmed, the logic level at the EA pin is sampled and latched during reset. If the device is powered up without a reset, the latch initializes to a random value, and holds that value until reset is activated. It is necessary that the latched value of EA be in agreement with the current logic level at that pin in order for the device to function properly. Programming the Flash The AT89LV51 is normally shipped with the on-chip Flash memory array in the erased state (i.e. contents=FFH) and ready to be programmed. The respective top-side marking and device signature codes are listed below: VPP = 12V Top-Side Mark AT89LV51 xxxx yyww Signature (030H) = 1EH (031H) = 61H (032H) = FFH 4-50 Not The AT89LV51 code memory array is programmed byteby-byte. To program any non-blank byte in the on-chip Flash Code Memory, the entire memory must be erased using the Chip Erase Mode. Programming Algorithm: Before programming the AT89LV51, the address, data and control signals should be set up according to the Flash programming mode table and Figure 3 and Figure 4. To program the AT89LV51, the following sequence should be followed: 1. Input the desired memory location on the address lines. 2. Input the appropriate data byte on the data lines. 3. Activate the correct combination of control signals. 4. Raise EA/VPP to 12V. 5. Pulse ALE/PROG once to program a byte in the Flash array or the lock bits. The byte-write cycle is self-timed and typically takes no more than 1.5 ms. Repeat steps 1 through 5 changing the address and data for the entire array or until the end of the object file is reached. Data Polling: The AT89LV51 features Data Polling to indicate the end of a write cycle. During a write cycle, an attempted read of the last byte written will result in the complement of the written data on PO.7. Once the write cycle has been completed, true data is valid on all outputs, and the next cycle may begin. Data Polling may begin any time after a write cycle has been initiated. Ready/Busy: The progress of byte programming can also be monitored by the RDY/BSY output signal. P3.4 is pulled low after ALE goes high during programming to indicate BUSY. P3.4 is pulled high again when programming is done to indicate READY. Program Verify: If lock bits LB1 and LB2 have not been programmed, the programmed code data can be read back via the address and data lines for verification. The lock bits cannot be verified directly. Verification of the lock bits is achieved by observing that their features are enabled. Chip Erase: The entire Flash array and the lock bits are erased electrically by using the proper combination of control signals and by holding ALE/PROG low for 10 ms. The code array is written with all “1”s. The chip erase operation must be executed before the code memory can be re-programmed. Reading the Signature Bytes: The signature bytes are read by the same procedure as a normal verification of locations 030H and 031H, except that P3.6 and P3.7 need to be pulled to a logic low. The values returned are: (030H) = 1EH indicates manufactured by Atmel (031H) = 61H indicates 89LV51 (032H) = FFH indicates 12V programming Not Programming Interface Every code byte in the Flash array can be written and the entire array can be erased by using the appropriate combination of control signals. The write operation cycle is selftimed and once initiated, will automatically time itself to completion. All major programming vendors offer worldwide support for the Atmel microcontroller series. Please contact your local programming vendor for the appropriate software revision. Flash Programming Modes Mode RST PSEN Write Code Data H L Read Code Data H L EA/VPP P2.6 P2.7 P3.6 P3.7 12V L H H H H L L H H Bit - 1 H L 12V H H H H Bit - 2 H L 12V H H L L Bit - 3 H L 12V H L H L Chip Erase H L 12V H L L L Read Signature Byte H L H L L L L Write Lock Note: ALE/PROG H (1) H 1. Chip Erase requires a 10-ms PROG pulse. Figure 3. Programming the Flash Figure 4. Verifying the Flash +5V AT89LV51 A0 - A7 ADDR. OOOOH/OFFFH A8 - A11 P1 P2.0 - P2.3 VCC P0 CC PGM DATA P2.6 SEE FLASH PROGRAMMING MODES TABLE ALE PROG XTAL2 EA VIH/VPP XTAL1 RST P2.7 P3.6 P3.7 3-12 MHz GND VIH PSEN 4-51 Flash Programming and Verification Characteristics TA = 0°C to 70°C, VCC = 5.0V ± 10% Symbol Parameter Min Max Units VPP(1) Programming Enable Voltage 11.5 12.5 V IPP(1) Programming Enable Current 25 µA 1/tCLCL Oscillator Frequency 12 MHz tAVGL Address Setup to PROG Low 48tCLCL tGHAX Address Hold After PROG 48tCLCL tDVGL Data Setup to PROG Low 48tCLCL tGHDX Data Hold After PROG 48tCLCL tEHSH P2.7 (ENABLE) High to VPP 48t CLCL tSHGL VPP Setup to PROG Low 10 µs VPP Hold After PROG 10 µs tGLGH PROG Width 1 tAVQV Address to Data Valid 48t CLCL tELQV ENABLE Low to Data Valid 48tCLCL tEHQZ Data Float After ENABLE tGHBL PROG High to BUSY Low 1.0 µs tWC Byte Write Cycle Time 2.0 ms tGHSL Note: 4-52 (1) 3 1. Only used in 12-volt programming mode. Not 0 110 µs 48tCLCL Not Flash Programming and Verification Waveforms (VPP = 12V) PROGRAMMING ADDRESS P1.0 - P1.7 P2.0 - P2.3 VERIFICATION ADDRESS tAVQV PORT 0 DATA IN tAVGL tDVGL tGHDX DATA OUT tGHAX ALE/PROG tSHGL tGLGH VPP tGHSL LOGIC 1 LOGIC 0 EA/VPP tEHSH tEHQZ tELQV P2.7 (ENABLE) tGHBL P3.4 (RDY/BSY) BUSY READY tWC 4-53 Absolute Maximum Ratings* Operating Temperature.................................. -55°C to +125°C *NOTICE: Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Storage Temperature ..................................... -65°C to +150°C Voltage on Any Pin with Respect to Ground .....................................-1.0V to +7.0V Maximum Operating Voltage ............................................ 6.6V DC Output Current...................................................... 15.0 mA DC Characteristics TA = -40°C to 85°C, VCC = 2.7V to 6.0V (unless otherwise noted) Symbol Parameter Condition Min Max Units VIL Input Low Voltage (Except EA) -0.5 0.2 VCC - 0.1 V VIL1 Input Low Voltage (EA) -0.5 0.2 VCC - 0.3 V VIH Input High Voltage 0.2 VCC + 0.9 VCC + 0.5 V VIH1 Input High Voltage 0.7 VCC VCC + 0.5 V IOL = 1.6 mA 0.45 V 0.45 V VOL (Except XTAL1, RST) (XTAL1, RST) Output Low Voltage (1) (Ports 1,2,3) Voltage (1) VOL1 Output Low (Port 0, ALE, PSEN) IOL = 3.2 mA VOH Output High Voltage (Ports 1,2,3, ALE, PSEN) IOH = -60 µA, VCC = 5V ± 10% VOH1 2.4 V IOH = -20 µA 0.75 VCC V IOH = -10 µA 0.9 VCC V 2.4 V IOH = -300 µA 0.75 VCC V IOH = -80 µA 0.9 VCC V IOH = -800 µA, VCC = 5V ± 10% Output High Voltage (Port 0 in External Bus Mode) IIL Logical 0 Input Current (Ports 1,2,3) VIN = 0.45V -50 µA ITL Logical 1 to 0 Transition Current (Ports 1,2,3) VIN = 2V -650 µA ILI Input Leakage Current (Port 0, EA) 0.45 < VIN < VCC ±10 µA RRST Reset Pulldown Resistor 300 KΩ CIO Pin Capacitance Test Freq. = 1 MHz, TA = 25°C 10 pF ICC Power Supply Current Active Mode, 12 MHz, VCC = 6V/3V 20/5.5 mA Idle Mode, 12 MHz, VCC = 6V/3V 5/1 mA VCC = 6V 100 µA VCC = 3V 20 µA Power Down Mode Notes: 4-54 50 (2) 1. Under steady state (non-transient) conditions, IOL must be externally limited as follows: Maximum IOL per port pin: 10 mA Maximum IOL per 8-bit port: Port 0: 26 mA Ports 1, 2, 3: 15 mA Not Maximum total IOL for all output pins: 71mA If IOL exceeds the test condition, VOL may exceed the related specification. Pins are not guaranteed to sink current greater than the listed test conditions. 2. Minimum VCC for Power Down is 2V. Not AC Characteristics Under operating conditions, load capacitance for Port 0, ALE/PROG, and PSEN = 100 pF; load capacitance for all other outputs = 80 pF. External Program and Data Memory Characteristics Symbol Parameter 12 MHz Oscillator Min Max Variable Oscillator Min Max 0 12 Units 1/tCLCL Oscillator Frequency tLHLL ALE Pulse Width 127 2tCLCL-40 ns tAVLL Address Valid to ALE Low 43 tCLCL-40 ns tLLAX Address Hold After ALE Low 48 tCLCL-35 ns tLLIV ALE Low to Valid Instruction In tLLPL ALE Low to PSEN Low 43 tCLCL-40 ns tPLPH PSEN Pulse Width 205 3tCLCL-45 ns tPLIV PSEN Low to Valid Instruction In tPXIX Input Instruction Hold After PSEN tPXIZ Input Instruction Float After PSEN tPXAV PSEN to Address Valid tAVIV Address to Valid Instruction In 312 5tCLCL-105 ns tPLAZ PSEN Low to Address Float 10 10 ns tRLRH RD Pulse Width 400 6tCLCL-100 ns tWLWH WR Pulse Width 400 6tCLCL-100 ns tRLDV RD Low to Valid Data In tRHDX Data Hold After RD tRHDZ Data Float After RD 97 2tCLCL-70 ns tLLDV ALE Low to Valid Data In 517 8tCLCL-150 ns tAVDV Address to Valid Data In 585 9tCLCL-165 ns tLLWL ALE Low to RD or WR Low 200 3tCLCL+50 ns tAVWL Address to RD or WR Low 203 4tCLCL-130 ns tQVWX Data Valid to WR Transition 23 tCLCL-60 ns tQVWH Data Valid to WR High 433 7tCLCL-150 ns tWHQX Data Hold After WR 33 tCLCL-50 ns tRLAZ RD Low to Address Float tWHLH RD or WR High to ALE High 233 4tCLCL-100 145 0 3tCLCL-105 0 59 75 tCLCL-8 0 5tCLCL-165 3tCLCL-50 0 43 123 tCLCL-40 ns ns ns 0 300 ns ns tCLCL-25 252 MHz ns ns 0 ns tCLCL+40 ns 4-55 External Program Memory Read Cycle tLHLL ALE tAVLL tLLIV tLLPL tPLIV PSEN tPXAV tPLAZ tPXIZ tLLAX tPXIX A0 - A7 PORT 0 tPLPH INSTR IN A0 - A7 tAVIV PORT 2 A8 - A15 A8 - A15 External Data Memory Read Cycle tLHLL ALE tWHLH PSEN tLLDV tRLRH tLLWL RD tLLAX tAVLL PORT 0 tRLDV tRLAZ A0 - A7 FROM RI OR DPL tRHDZ tRHDX DATA IN A0 - A7 FROM PCL INSTR IN tAVWL tAVDV PORT 2 4-56 P2.0 - P2.7 OR A8 - A15 FROM DPH Not A8 - A15 FROM PCH Not External Data Memory Write Cycle tLHLL ALE tWHLH PSEN tLLWL WR tAVLL tLLAX tQVWX A0 - A7 FROM RI OR DPL PORT 0 tWLWH tWHQX tQVWH DATA OUT A0 - A7 FROM PCL INSTR IN tAVWL PORT 2 P2.0 - P2.7 OR A8 - A15 FROM DPH A8 - A15 FROM PCH External Clock Drive Waveforms tCHCX VCC - 0.5V tCHCX tCLCH tCHCL 0.7 VCC 0.2 VCC - 0.1V 0.45V tCLCX tCLCL External Clock Drive Symbol Parameter 1/tCLCL Oscillator Frequency tCLCL Clock Period tCHCX Min Max Units 0 12 MHz 83.3 ns High Time 20 ns tCLCX Low Time 20 ns tCLCH Rise Time 20 ns tCHCL Fall Time 20 ns 4-57 Serial Port Timing: Shift Register Mode Test Conditions (VCC = 2.7V to 6V; Load Capacitance = 80 pF) Symbol Parameter 12 MHz Osc Min Variable Oscillator Max Min Units Max tXLXL Serial Port Clock Cycle Time 1.0 12tCLCL µs tQVXH Output Data Setup to Clock Rising Edge 700 10tCLCL-133 ns tXHQX Output Data Hold After Clock Rising Edge 50 2tCLCL-117 ns tXHDX Input Data Hold After Clock Rising Edge 0 0 ns tXHDV Clock Rising Edge to Input Data Valid 700 10t CLCL-133 ns Shift Register Mode Timing Waveforms INSTRUCTION ALE 0 1 2 3 4 5 6 7 8 tXLXL CLOCK tQVXH tXHQX WRITE TO SBUF 0 1 CLEAR RI VALID 3 4 5 6 tXHDX tXHDV OUTPUT DATA 2 VALID SET TI VALID VALID VALID VALID VALID AC Testing Input/Output Waveforms (1) Note: 4-58 1. Float Waveforms (1) V LOAD+ 0.2 VCC + 0.9V TEST POINTS 0.45V VALID SET RI INPUT DATA VCC - 0.5V 7 Not V LOAD - Note: 1. V OL - 0.1V V OL + 0.1V Timing Reference Points V LOAD 0.2 VCC - 0.1V AC inputs during testing are driven at 2.4V for a logic “1” and 0.45V for a logic “0”. Timing measurements are made at 2.0V for a logic “1” and 0.8V for a logic “0”. 0.1V 0.1V For timing purposes, a port pin is no longer floating when a 100 mV change from load voltage occurs. A port pin begins to float when a 100 mV change from the loaded VOH/VOL level occurs. Not AT89LV51 ICC (mA) o TYPICAL ICC (ACTIVE) at 25 C 24 VCC = 6.0 V 20 16 VCC = 5.0 V 12 8 VCC = 3.0 V 4 0 0 4 8 12 16 20 24 F (MHz) AT89LV51 ICC (mA) TYPICAL ICC (IDLE) at 25 o C 4.8 VCC = 6.0 V 4.0 3.2 VCC = 5.0 V 2.4 1.6 VCC = 3.0 V 0.8 0.0 0 4 8 12 16 20 24 F (MHz) AT89LV51 TYPICAL ICC vs. VOLTAGE- POWER DOWN (85°C) 20 I 15 C C 10 µ A 5 0 3.0V 4.0V 5.0V 6.0V Vcc VOLTAGE Notes: 1. XTAL1 tied to GND for Icc (power down) 2. Lock bits programmed 4-59 Ordering Information Speed (MHz) Power Supply Ordering Code Package 12 2.7V to 6V AT89LV51-12AC AT89LV51-12JC AT89LV51-12PC 44A 44J 40P6 Commercial (0° C to 70° C) 12 2.7V to 6V AT89LV51-12AI AT89LV51-12JI AT89LV51-12PI 44A 44J 40P6 Industrial (-40° C to 85° C) Package Type 44A 44 Lead, Thin Plastic Gull Wing Quad Flatpack (TQFP) 44J 44 Lead, Plastic J-Leaded Chip Carrier (PLCC) 40P6 40 Lead, 0.600" Wide, Plastic Dull Inline Package (PDIP) 4-60 Not Operation Range