ACAC 0612, ACAS 0612 - Precision Vishay Beyschlag Precision Thin Film Chip Resistor Array FEATURES • • • • • ACAC 0612 (concave terminations) and ACAS 0612 (convex terminations) thin chip resistor arrays combine the proven reliability of precision thin film chip resistor products with the advantages of chip resistor arrays. Defined tolerance matching and TCR tracking makes this product perfectly suited for applications with outstanding requirements towards stable fixed resistor ratios. A small package enables the design of high density circuits in combination with reduction of assembly costs. Four equal resistor values or two pairs are available. Advanced thin film technology Two pairs or four equal resistor values TCR tracking down to 10 ppm/K (± 5 ppm/K) Tolerance matching down to 0.1 % (± 0.05 %) Pure Sn termination on Ni barrier layer • RoHS compliant component, compatible with lead (Pb)-free and lead containing soldering processes APPLICATIONS • Precision analogue circuits • Voltage divider • Feedback circuits • Signal conditioning TECHNICAL SPECIFICATIONS DESCRIPTION EIA size Metric size Configuration, isolated Design: All Equal Two Pairs Resistance values Absolute tolerance ACAC 0612, ACAS 0612 0612 RR1632M 4 x 0603 Tolerance matching Absolute temperature coefficient Temperature coefficient tracking Max. resistance ratio Rmin./Rmax. Rated dissipation: P70 (3) Element Package, 4 x 0603 Operating voltage Film temperature Insulation voltage (Uins) against ambient and between isolated resistors, continuous AE TP 47 Ω to 221 kΩ (1) ± 0.5 %; ± 0.25 % 0.5 % (equivalent to ± 0.25 %) 0.25 % (equivalent to ± 0.125 %) 0.1 % (equivalent to ± 0.05 %) ± 50 ppm/K; ± 25 ppm/K 50 ppm/K (equivalent to ± 25 ppm/K) 25 ppm/K (equivalent to ± 12.5 ppm/K) 15 ppm/K (equivalent to ± 7.5 ppm/K) 10 ppm/K (equivalent to ± 5 ppm/K) 1:5 (2) 0.1 W 0.3 W 75 V 125 °C (4) 75 V Notes (1) Resistance values to be selected from E24, E48 and E96 (2) Higher resistance ratio is available on request (3) The power dissipation on the resistor generates a temperature rise against the local ambient, depending on the heat-flow support of the printed circuit board (thermal resistance). The rated dissipation applies only if the permitted film temperature is not exceeded. Furthermore, a high level of ambient temperature or of power dissipation may raise the temperature of the solder joint, hence special solder alloys or board materials may be required to maintain the reliability of the assembly. (4) For higher max. film temperature and AEC-Q200 qualification please refer to data sheet “Automotive Precision Thin Film Chip Resistor Array“ available on our web site at www.vishay.com • These resistors do not feature a limited lifetime when operated within the permissible limits. However, resistance value drift increasing over operating time may result in exceeding a limit acceptable to the specific application, thereby establishing a functional lifetime. www.vishay.com 276 For technical questions, contact: [email protected] Document Number: 28751 Revision: 11-Sep-08 ACAC 0612, ACAS 0612 - Precision Precision Thin Film Chip Resistor Array Vishay Beyschlag PART NUMBER AND PRODUCT DESCRIPTION (1) PART NUMBER: ACASA1100A2200P500 A C A S A 1 1 0 RESISTANCE VALUE (2) (3) MODEL TERMINAL SIZE ACA C = Concave S = Convex A = 0612 0 A ACCURACY GRADE (4) 3 digit TCR, Tracking, resistance Tolerance and value R1, R4 Matching 1 digit multiplier A, B, E, F, MULTIPLIER J, K, N or P 9 = *10-1 0 = *100 1 = *101 2 = *102 3 = *103 2 2 0 RESISTANCE VALUE (2) (3) 0 P 5 0 0 PACKAGING (5) SPECIAL P1 P5 PW 00 = Standard 3 digit resistance value R2, R3 1 digit multiplier MULTIPLIER 9 = *10-1 0 = *100 1 = *101 2 = *102 3 = *103 PRODUCT DESCRIPTION: ACAS 0612 110R A 220R P5 ACA S 0612 110R A 220R P5 MODEL TERMINATION SIZE RESISTANCE VALUE R1, R4 (2) (3) ACCURACY GRADE (4) RESISTANCE VALUE R2, R3 (2) (3) PACKAGING (5) ACA = Chip Array C = Concave S = Convex 0612 110R = 110 Ω 1K1 = 1.1 kΩ 22K1 = 22.1 kΩ TCR, Tracking, Tolerance and Matching A, B, E, F, J, K, N or P 220R = 220 Ω 1K1 = 1.1 kΩ 22K1 = 22.1 kΩ P1 P5 PW Notes (1) Products can be ordered using either the PART NUMBER or the PRODUCT DESCRIPTION (2) R = R ≤ R = R ; please refer to APPLICATION INFORMATION, see below 1 4 2 3 (3) Different resistance values are available on request (4) Please refer to table TEMPERATURE COEFFICIENT AND RESISTANCE RANGE, see below (5) Please refer to table PACKAGING, see below PACKAGING MODEL PACKAGING CODE TAPE WIDTH DIAMETER PIECES PITCH 8 mm 180 mm/7" 1000 4 mm 8 mm 180 mm/7" 5000 4 mm P5 8 mm 330 mm/13" 10 000 4 mm PW ACAC 0612 ACAS 0612 PAPER TAPE P1 DIMENSIONS ACAC 0612 in millimeters WT WT I1 I2 T1 T2 Top view Bottom view DIMENSIONS - chip resistor array, mass and relevant physical dimensions TYPE ACAC 0612 L (mm) W (mm) H (mm) P (mm) WT (mm) T1 (mm) T2 (mm) d (mm) l1 (mm) l2 (mm) 1.6 ± 0.15 3.2 ± 0.15 0.55 ± 0.1 0.8 ± 0.1 0.5 ± 0.15 0.3 ± 0.15 0.4 ± 0.15 0.3 ± 0.1 min. 0.15 min. 0.25 Document Number: 28751 Revision: 11-Sep-08 For technical questions, contact: [email protected] MASS (mg) 9.53 www.vishay.com 277 ACAC 0612, ACAS 0612 - Precision Precision Thin Film Chip Resistor Array Vishay Beyschlag DIMENSIONS ACAS 0612 in millimeters A T2 T1 H A1 A DIMENSIONS - chip resistor array, mass and relevant physical dimensions TYPE ACAS 0612 W (mm) L (mm) H (mm) P (mm) A1 (mm) A (mm) T1 (mm) T2 (mm) MASS (mg) 1.5 ± 0.15 3.2 ± 0.15 0.45 ± 0.1 0.8 ± 0.1 0.6 ± 0.15 0.4 ± 0.15 0.3 ± 0.15 0.4 ± 0.15 6.59 Z Dimensions in mm limits for solder resistance PATTERN STYLES FOR CHIP RESISTOR ARRAYS ACAC 0612 ACAS 0612 U I X 0.1 Y Z G G Y X I P P 0.1 RECOMMENDED SOLDER PAD DIMENSIONS FOR CHIP RESISTOR ARRAYS G (mm) Y (mm) X (mm) U (mm) Z (mm) I (mm) P (mm) ACAC 0612 0.7 0.7 0.5 - 2.1 0.3 0.8 ACAS 0612 0.8 1.15 0.64 0.44 3.1 0.36 0.8 TYPE TEMPERATURE COEFFICIENT AND RESISTANCE RANGE DESCRIPTION RESISTANCE VALUE ACCURACY GRADE ABSOLUTE TCR TCR TRACKING (1) ABSOLUTE TOLERANCE TOLERANCE MATCHING (1) ACAC 0612, ACAS 0612 A ± 25 ppm/K 10 ppm/K ± 0.25 % 0.1 % 47 Ω to 221 kΩ B ± 25 ppm/K 10 ppm/K ± 0.5 % 0.25 % 47 Ω to 221 kΩ E ± 25 ppm/K 15 ppm/K ± 0.25 % 0.1 % 47 Ω to 221 kΩ F ± 25 ppm/K 15 ppm/K ± 0.5 % 0.25 % 47 Ω to 221 kΩ J ± 25 ppm/K 25 ppm/K ± 0.25 % 0.1 % 47 Ω to 221 kΩ K ± 25 ppm/K 25 ppm/K ± 0.5 % 0.25 % 47 Ω to 221 kΩ N ± 50 ppm/K 25 ppm/K ± 0.5 % 0.5 % 47 Ω to 221 kΩ P ± 50 ppm/K 50 ppm/K ± 0.5 % 0.5 % 47 Ω to 221 kΩ Note (1) In applications with defined resistance ratios like voltage dividers or feedback circuits, an array with a defined tracking of e.g. 10 ppm/K is required to replace discrete resistors with a temperature coefficient of ± 5 ppm/K. Furthermore, in order to achieve the same tolerance of ± 0.05 % of individual resistors, an array requires a matching of 0.1 %. www.vishay.com 278 For technical questions, contact: [email protected] Document Number: 28751 Revision: 11-Sep-08 ACAC 0612, ACAS 0612 - Precision Precision Thin Film Chip Resistor Array APPLICATION INFORMATION R1 R2 R3 Vishay Beyschlag ASSEMBLY R4 Circuit Type 03 DESCRIPTION The production of the components is strictly controlled and follows an extensive set of instructions established for reproducibility. A homogeneous film of metal alloy is deposited on a high grade (96 % Al2O3) ceramic substrate and conditioned to achieve the desired temperature coefficient. Specially designed inner contacts are realised on both sides. A special laser is used to achieve the target value by smoothly cutting a meander groove in the resistive layer without damaging the ceramics. The resistor elements are covered by a protective coating designed for electrical, mechanical and climatic protection. The terminations receive a final pure tin on nickel plating. The result of the determined production is verified by an extensive testing procedure and optical inspection performed on 100 % of the individual chip resistors. Only accepted products are laid directly into the paper tape in accordance with IEC 60286-3*. The resistors are suitable for processing on automatic SMD assembly systems. They are suitable for automatic soldering using reflow or vapour phase as shown in IEC 61760-1*. For ACAC resistor arrays automatic soldering using wave can also be used. The encapsulation is resistant to all cleaning solvents commonly used in the electronics industry, including alcohols, esters and aqueous solutions. The suitability of conformal coatings, if applied, shall be qualified by appropriate means to ensure the long-term stability of the whole system. The resistors are RoHS compliant; the pure tin plating provides compatibility with lead (Pb)-free and lead-containing soldering processes. The permitted storage time is 20 years, whereas the solderability is specified for 2 years after production or requalification. The immunity of the plating against tin whisker growth has been proven under extensive testing. All products comply with the GADSL (1) and the CEFIC-EECA-EICTA (2) list of legal restrictions on hazardous substances. This includes full compliance with the following directives: • 2000/53/EC End of Vehicle life Directive (ELV) and Annex II (ELV II) • 2002/95/EC Restriction of Substances directive (RoHS) the use of Hazardous • 2002/96/EC Waste Electrical and Electronic Equipment Directive (WEEE) APPROVALS Where applicable, the resistors are tested in accordance with EN 140401-801 which refers to EN 60115-1 and EN 140400. Notes (1) Global Automotive Declarable Substance List, see www.gadsl.org (2) CEFIC (European Chemical Industry Council), EECA (European Electronic Component Manufacturers Association), EICTA (European trade organisation representing the information and communications technology and consumer electronics), see www.eicta.org → issues → environment policy → chemicals → chemicals for electronics • The quoted IEC standards marked with an asterisk (*) are also released as EN standards with the same number and identical contents Document Number: 28751 Revision: 11-Sep-08 For technical questions, contact: [email protected] www.vishay.com 279 ACAC 0612, ACAS 0612 - Precision Vishay Beyschlag Precision Thin Film Chip Resistor Array TESTS AND REQUIREMENTS Essentially all tests are carried out in accordance with the following specifications: EN 60115-1, Generic specification (includes tests) EN 140400, Sectional specification (includes schedule for qualification approval) The testing also covers most of the requirements specified by EIA/IS-703 and JIS-C-5202. The tests are carried out in accordance with IEC 60068* and under standard atmospheric conditions according to IEC 60068-1*, 5.3. Climatic category LCT/UCT/56 (rated temperature range: Lower Category Temperature, Upper Category Temperature; damp heat, long term, 56 days) is valid. Unless otherwise specified the following values apply: Temperature: 15 °C to 35 °C Relative humidity: 45 % to 75 % Air pressure: 86 kPa to 106 kPa (860 mbar to 1060 mbar) In the following table only the tests and requirements are listed with reference to the relevant clauses of EN 60115-1 and IEC 60068-2*; a short description of the test procedure is also given. TEST PROCEDURES AND REQUIREMENTS EN 60115-1 CLAUSE IEC 60068-2* TEST METHOD TEST PROCEDURE REQUIREMENTS (1) PERMISSIBLE CHANGE (ΔR) Stability for product types: 4.5 - Resistance 4.8.4.2 - Temperature coefficient 4.25.1 - Endurance 4.25.3 - Endurance at upper category temperature Damp heat, steady state ACAC 0612, ACAS 0612 Climatic category (LCT/UCT/duration) At 20/LCT/ 20 °C and 20/UCT/20 °C U = P 70 x R or U = Umax.; 1.5 h on; 0.5 h off; 70 °C; 1000 h 125 °C; 1000 h 4.24 78 (Cab) 4.13 - Short time overload (2) 4.19 14 (Na) Rapid change of temperature 4.18.2 58 (Td) Resistance to soldering heat 4.17.2 58 (Td) Solderability 4.32 21 (Ue3) Shear (adhesion) (40 ± 2) °C; 56 days; (93 ± 3) % RH U = 2.5 x P 70 x R or U = 2 x Umax.; 5 s 30 min at LCT and 30 min at UCT; 5 cycles Reflow method 2 (IR/forced gas convention); (260 ± 5) °C; (10 ± 1) s Solder bath method; SnPb; non-activated flux accelerated ageing 4 h/155 °C (215 ± 3) °C; (3 ± 0.3) s Solder bath method; SnAgCu; non-activated flux accelerated ageing 4 h/155 °C (235 ± 3) °C; (2 ± 0.2) s 45 N 4.33 21 (Ue1) Substrate bending Depth 2 mm, 3 times 4.7 - Voltage proof Urms = Uins 60 ± 5 s; against ambient, between adjacent resistors 47 Ω to 221 kΩ - 55 °C/+ 125 °C/56 days ± 0.5 %; ± 0.25 % ± 50 ppm/K; ± 25 ppm/K ± (0.25 % R + 0.05 Ω) ± (0.25 % R + 0.05 Ω) ± (0.25 % R + 0.05 Ω) ± (0.1 % R + 0.01 Ω) no visible damage ± (0.1 % R + 0.01 Ω) no visible damage ± (0.1 % R + 0.01 Ω) no visible damage Good tinning (≥ 95 % covered); no visible damage No visible damage ± (0.1 % R + 0.01 Ω) no visible damage; no open circuit in bent position No flashover or breakdown Notes (1) Figures are given for equal values (2) For a single element • The quoted IEC standards marked with an asterisk (*) are also released as EN standards with the same number and identical contents www.vishay.com 280 For technical questions, contact: [email protected] Document Number: 28751 Revision: 11-Sep-08 Legal Disclaimer Notice Vishay Disclaimer All product specifications and data are subject to change without notice. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained herein or in any other disclosure relating to any product. Vishay disclaims any and all liability arising out of the use or application of any product described herein or of any information provided herein to the maximum extent permitted by law. The product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein, which apply to these products. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications unless otherwise expressly indicated. Customers using or selling Vishay products not expressly indicated for use in such applications do so entirely at their own risk and agree to fully indemnify Vishay for any damages arising or resulting from such use or sale. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. Product names and markings noted herein may be trademarks of their respective owners. Document Number: 91000 Revision: 18-Jul-08 www.vishay.com 1