D100I Series High Isolation Miniature, 1W SIP DC/DC Converters Electrical Specifications Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice. Key Features: • 1W Output Power • Miniature SIP Case • 3,000 VDC Isolation • Single & Dual Outputs • Complies to RFI Standards • >1.12 MHour MTBF • 36 Standard Models • Industry Standard Pin-Out RoHS Compliant Input Parameter Input Voltage Range Input Filter Reflected Ripple Current Conditions Min. 5 VDC Input 4.5 12 VDC Input 10.8 24 VDC Input 21.6 48 VDC Input 43.2 Internal Capacitor 12 μH Source Inductance Typ. 5.0 12.0 24.0 48.0 Max. 5.5 13.2 26.4 52.8 20 Units VDC mA P - P Output Parameter Output Voltage Accuracy Output Voltage Balance Line Regulation Load Regulation (Note 1) Ripple & Noise (20 MHz) (Note 2) Output Power Protection Temperature Coefficient Output Short Circuit Conditions Min. Typ. ±3.0 Dual Output , Balanced Loads ±1.0 For Vin Change of 1% ±1.2 See Model Selection Guide 75 110 Max. ±0.02 Units % % % mV P - P % %/ºC Momentary (0.5 Sec.) General Parameter Isolation Voltage Isolation Resistance Isolation Capacitance Switching Frequency EMI/RFI Conditions Units VDC MΩ 60 pF 80 kHz EN55022 B, EN55024 B, IEC 61000-4-2, IEC 61000-4-3, FCC 47 CFR Part 15 B 60 Seconds 500 VDC 100 kHz, 1V Min. 3,000 1,000 Typ. Max. Min. -40 Typ. +25 Max. +85 +100 +125 Units ºC ºC ºC 95 % Environmental Parameter Operating Temperature Range Operating Temperature Range Storage Temperature Range Cooling Humidity MicroPower Direct 292 Page Street Suite D Stoughton, MA 02072 USA T: (781) 344-8226 F: (781) 344-8481 E: [email protected] W: www.micropowerdirect.com Conditions Ambient Case -40 Free Air Convection RH, Non-condensing Physical Case Size (5V 12V & 24V Input Models) Case Size (48V Input Models) Case Material Weight 0.76 x 0.24 x 0.39 Inches (19.5 x 6.0 x 10.0 mm) 0.76 x 0.28 x 0.39 Inches (19.5 x 7.2 x 10.0 mm) Non-Conductive Black Plastic (UL94-V0) 0.08 Oz (2.3g) Reliability Specifications Parameter MTBF Conditions MIL HDBK 217F, 25ºC, Gnd Benign Min. 1.12 Typ. Max. Units MHours Min. -0.7 -0.7 -0.7 -0.7 Typ. Max. 7.0 15.0 28.0 54.0 260 450 Units Absolute Maximum Ratings Parameter Input Voltage Surge (1 Sec) Lead Temperature Internal Power Dissipation Conditions 5 VDC Input 12 VDC Input 24 VDC Input 48 VDC Input 1.5 mm From Case For 10 Sec All Models VDC ºC mW Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings. Model Selection Guide Model Number D101I D102I D103I D104I D105I D106I D107I D108I D109I D111I D112I D113I D114I D115I D116I D117I D118I D119I D121I D122I D123I D124I D125I D126I D127I D128I D129I D131I D132I D133I D134I D135I D136I D137I D138I D139I Input Output Load Voltage (VDC) Current (mA) Regulation Voltage Current Current Nominal Range Full-Load No-Load (VDC) (mA, Max) (mA, Min) (%, Max) 5 4.5 - 5.5 267 30 3.3 303.0 6.0 10 5 4.5 - 5.5 256 30 5.0 200.0 4.0 10 5 4.5 - 5.5 267 30 9.0 111.0 2.2 10 5 4.5 - 5.5 263 30 12.0 83.3 1.6 10 5 4.5 - 5.5 263 30 15.0 66.6 1.3 10 5 4.5 - 5.5 270 30 ±5.0 ±100.0 ±2.0 10 5 4.5 - 5.5 256 30 ±9.0 ±55.5 ±1.1 10 5 4.5 - 5.5 256 30 ±12.0 ±41.6 ±0.8 10 5 4.5 - 5.5 250 30 ±15.0 ±33.3 ±0.6 10 12 10.8 - 13.2 113 20 3.3 303.0 6.0 10 12 10.8 - 13.2 113 20 5.0 200.0 4.0 10 12 10.8 - 13.2 111 20 9.0 111.0 2.2 10 12 10.8 - 13.2 108 20 12.0 83.3 1.6 10 12 10.8 - 13.2 106 20 15.0 66.6 1.3 10 12 10.8 - 13.2 111 20 ±5.0 ±100.0 ±2.0 10 12 10.8 - 13.2 109 20 ±9.0 ±55.5 ±1.1 10 12 10.8 - 13.2 106 20 ±12.0 ±41.6 ±0.8 10 12 10.8 - 13.2 104 20 ±15.0 ±33.3 ±0.6 10 24 21.6 - 26.4 56 10 3.3 303.0 6.0 10 24 21.6 - 26.4 54 10 5.0 200.0 4.0 10 24 21.6 - 26.4 56 10 9.0 111.0 2.2 10 24 21.6 - 26.4 53 10 12.0 83.3 1.6 10 24 21.6 - 26.4 53 10 15.0 66.6 1.3 10 24 21.6 - 26.4 56 10 ±5.0 ±100.0 ±2.0 10 24 21.6 - 26.4 54 10 ±9.0 ±55.5 ±1.1 10 24 21.6 - 26.4 53 10 ±12.0 ±41.6 ±0.8 10 24 21.6 - 26.4 53 10 ±15.0 ±33.3 ±0.6 10 48 43.2 - 52.8 29 6 3.3 303.0 6.0 10 48 43.2 - 52.8 29 6 5.0 200.0 4.0 10 48 43.2 - 52.8 28 6 9.0 111.0 2.2 10 48 43.2 - 52.8 28 6 12.0 83.3 1.6 10 48 43.2 - 52.8 28 6 15.0 66.6 1.3 10 48 43.2 - 52.8 30 6 ±5.0 ±100.0 ±2.0 10 48 43.2 - 52.8 29 6 ±9.0 ±55.5 ±1.1 10 48 43.2 - 52.8 28 6 ±12.0 ±41.6 ±0.8 10 48 43.2 - 52.8 28 6 ±15.0 ±33.3 ±0.6 10 Fuse Rating Slow-Blow (mA) 500 500 500 500 500 500 500 500 500 200 200 200 200 200 200 200 200 200 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 Efficiency (%, Typ) 75 78 75 76 76 74 78 78 80 74 74 75 77 78 75 76 78 80 75 77 75 78 78 74 76 78 78 72 72 74 74 75 70 72 74 74 Pin Connections Other input/output combinations are available (i.e. 24.0 VDC). Contact the factory for details at: [email protected] Pin 1 2 5 Notes: 1. Output load regulation is specified for a load change of 20% to 100%. 2. These units do not require external components to operate, but the use of an input capacitor (10 μF) may enhance performance in some applications. It is recommended that an input capacitor of 4.7 uF to 47 uF (dependent upon the application) be used on 48V input model. An output capacitor (4.7 μF to 100 μF or ±4.7 μF to ±68 μF) may be used to reduce ripple. To improve EMI performance, a simple filter network consisting of a 10 uF to 100 uF capacitor and 12 uH inductor should be effective. 3. These units will operate at no load without damage, but may not meet all specifications. 4. Dual output units may be connected to provide a 10V, 18V, 24V or 30 VDC output. To do this, connect the load across the positive (+Vout) and negative (-Vout) outputs and float the output common. 5. It is recommended that a fuse be used on the input of a power supply for protection. See the table above for the correct rating. Single +Vin -Vin -Vout Dual +Vin -Vin -Vout Pin 6 7 Single No Pin +Vout Dual Common +Vout Mechanical Dimensions Derating Curve Capacitive Load Single Output (μF Max) 220 Dual Output (μF Max) ±100 MicroPower Direct www.micropowerdirect.com 292 Page Street, STE D, Stoughton, MA 02072 • TEL: (781) 344-8226 • Notes: • All dimensions dimens are typical in inches (mm) • Tolerance xx.xx = ±0.01 (±0.25) • Pin 1 is marked by a “dot” or indentation on mar the side of the unit FAX: (781) 344-8481 • E-Mail: [email protected]