CYRF69303 Programmable Radio-on-Chip LPstar Programmable Radio-on-Chip LPstar Features ■ Operating temperature from 0 °C to 70 °C ■ Closed-loop frequency synthesis for minimal frequency drift ■ Radio System-on-Chip with built-in 8-bit MCU in a single device. ■ Operates in the unlicensed worldwide Industrial, Scientific, and Medical (ISM) band (2.400 GHz to 2.483 GHz). ■ Auto transaction sequencer (ATS): MCU can remain in sleep state longer to save power ■ On Air compatible with second WirelessUSB™ LP and PRoC LP. ■ Framing, length, CRC16, and Auto ACK ■ Pin-to-pin compatible with PRoC LP except the pin 31 and pin 37. ■ Separate 16 byte transmit and receive FIFOs ■ Receive signal strength indication (RSSI) ■ Built-in serial peripheral interface (SPI) control while in Sleep Mode generation radio Intelligent Simple Development ■ M8C based 8-bit CPU, optimized for human interface devices (HID) applications ■ Advanced development tools based on Cypress’s PSoC® tools ■ 256 bytes of SRAM ■ Flexible I/O ■ 8 Kbytes of flash memory with EEPROM emulation ■ 2 mA source current on all GPIO pins. Configurable 8 mA or 50 mA/pin current sink on designated pins ■ In-system reprogrammable through D+/D– pins ■ ■ CPU speed up to 12 MHz ■ 16-bit free running timer Each GPIO pin supports high impedance inputs, configurable pull up, open drain output, CMOS/TTL inputs, and CMOS output ■ Low power wakeup timer ■ Maskable interrupts on all I/O pins ■ 12-bit programmable interval timer with interrupts BOM Savings ■ Watchdog timer ■ Low external component count ■ Small footprint 40-pin QFN (6 mm × 6 mm) ■ GPIOs that require no external components Operates off a single crystal Low Power ■ 21 mA operating current (Transmit at –5 dBm) ■ Sleep current less than 1 A ■ ■ Operating voltage from 2.7 V to 3.6 V DC Applications ■ Fast startup and fast channel changes ■ Wireless keyboards and mice ■ Supports coin cell operated applications ■ Presentation tools ■ Wireless gamepads ■ Remote controls ■ Toys ■ Fitness Reliable & Robust ■ Receive sensitivity typical –90 dBm ■ AutoRate™ - Dynamic Data Rate Reception ❐ Enables data reception for any of the supported bit rates automatically. ❐ DSSS (250 Kbps), GFSK (1 Mbps) Cypress Semiconductor Corporation Document Number: 001-66502 Rev. *D • 198 Champion Court • San Jose, CA 95134-1709 • 408-943-2600 Revised April 27, 2013 CYRF69303 nSS VIO VCC1 VCC2 VCC3 VCC4 VBat0 VBat1 VBat2 VCC RST VDD_MICRO VCC SCK MOSI Logic Block Diagram RFbias RFp RFn Microcontroller Function P0_1,3,4,7 4 Radio Function IRQ/GPIO P1.5/MOSI MISO/GPIO P1.4/SCK P1_0:2,6:7 5 XOUT/GPIO P1.3/nSS 12 MHz Document Number: 001-66502 Rev. *D Vdd ..... GND GND RESV Xtal GND P2_0:1 2 ....... Page 2 of 70 CYRF69303 Contents Functional Description ..................................................... 4 Functional Overview ........................................................ 4 2.4 GHz Radio Function .............................................. 4 Data Transmission Modes ........................................... 4 Microcontroller Function .............................................. 4 Backward Compatibility ............................................... 4 Pinouts .............................................................................. 5 Pin Definitions .................................................................. 5 Functional Block Overview .............................................. 6 2.4 GHz Radio ............................................................. 6 Frequency Synthesizer ................................................ 6 Baseband and Framer ................................................. 6 Packet Buffers and Radio Configuration Registers ..... 7 Auto Transaction Sequencer (ATS) ............................ 7 Interrupts ..................................................................... 7 Clocks .......................................................................... 8 GPIO Interface ............................................................ 8 Power-on Reset ........................................................... 8 Timers ......................................................................... 8 Power Management .................................................... 8 Low Noise Amplifier (LNA) and Received Signal Strength Indication (RSSI) ....................... 9 SPI Interface ...................................................................... 9 Three-Wire SPI Interface ............................................. 9 Four-Wire SPI Interface ............................................... 9 SPI Communication and Transactions ...................... 10 SPI I/O Voltage References ...................................... 10 SPI Connects to External Devices ............................ 10 CPU Architecture ............................................................ 11 CPU Registers ................................................................. 11 Flags Register ........................................................... 11 Accumulator Register ................................................ 12 Index Register ........................................................... 12 Stack Pointer Register ............................................... 12 CPU Program Counter High Register ....................... 12 CPU Program Counter Low Register ........................ 12 Addressing Modes ......................................................... 13 Source Immediate ..................................................... 13 Source Direct ............................................................. 13 Source Indexed ......................................................... 13 Destination Direct ...................................................... 13 Destination Indexed ................................................... 14 Destination Direct Source Immediate ........................ 14 Destination Indexed Source Immediate .................... 14 Destination Direct Source Direct ............................... 14 Source Indirect Post Increment ................................. 15 Destination Indirect Post Increment .......................... 15 Instruction Set Summary ............................................... 16 Memory Organization ..................................................... 17 Flash Program Memory Organization ....................... 17 Data Memory Organization ....................................... 18 Flash .......................................................................... 18 Document Number: 001-66502 Rev. *D SROM ........................................................................ 18 SROM Function Descriptions .................................... 19 Clocking .......................................................................... 22 SROM Table Read Description ................................. 23 Clock Architecture Description .................................. 24 CPU Clock During Sleep Mode ................................. 28 Reset ................................................................................ 29 Power-on Reset ......................................................... 30 Watchdog Timer Reset .............................................. 30 Sleep Mode ...................................................................... 30 Sleep Sequence ........................................................ 30 Low Power in Sleep Mode ......................................... 31 Wakeup Sequence .................................................... 31 Power-on Reset Control ................................................. 32 POR Compare State ................................................. 33 ECO Trim Register .................................................... 33 General-Purpose I/O Ports ............................................. 33 Port Data Registers ................................................... 33 GPIO Port Configuration ........................................... 35 GPIO Configurations for Low Power Mode ............... 41 Serial Peripheral Interface (SPI) ................................ 42 SPI Data Register ...................................................... 43 SPI Configure Register .............................................. 43 SPI Interface Pins ...................................................... 45 Timer Registers .............................................................. 45 Registers ................................................................... 45 Interrupt Controller ......................................................... 48 Architectural Description ........................................... 48 Interrupt Processing .................................................. 49 Interrupt Latency ....................................................... 49 Interrupt Registers ..................................................... 49 Microcontroller Function Register Summary ............. 54 Radio Function Register Summary ............................... 56 Absolute Maximum Ratings .......................................... 57 DC Characteristics ......................................................... 57 AC Characteristics ......................................................... 59 Switching Waveforms .................................................... 60 RF Characteristics .......................................................... 63 Ordering Information ...................................................... 65 Ordering Code Definitions ......................................... 65 Package Handling ........................................................... 66 Package Diagrams .......................................................... 66 Acronyms ........................................................................ 68 Document Conventions ................................................. 68 Units of Measure ....................................................... 68 Document History Page ................................................. 69 Sales, Solutions, and Legal Information ...................... 70 Worldwide Sales and Design Support ....................... 70 Products .................................................................... 70 PSoC Solutions ......................................................... 70 Page 3 of 70 CYRF69303 Functional Description PRoC LPstar devices are integrated radio and microcontroller functions in the same package to provide a dual-role single-chip solution. Communication between the microcontroller and the radio is through the radio’s SPI interface. Functional Overview The CYRF69303 is a complete Radio System-on-Chip device, providing a complete RF system solution with a single device and a few discrete components. The CYRF69303 is designed to implement low-cost wireless systems operating in the worldwide 2.4 GHz Industrial, Scientific, and Medical (ISM) frequency band (2.400 GHz to 2.4835 GHz). 2.4 GHz Radio Function The SoC contains a 2.4 GHz, 1 Mbps GFSK radio transceiver, packet data buffering, packet framer, DSSS baseband controller, received signal strength indication (RSSI), and SPI interface for data transfer and device configuration. The radio supports 98 discrete 1 MHz channels (regulations may limit the use of some of these channels in certain jurisdictions). The baseband performs DSSS spreading/despreading, Start of Packet (SOP), End of Packet (EOP) detection, and CRC16 generation and checking. The baseband may also be configured to automatically transmit Acknowledge (ACK) handshake packets whenever a valid packet is received. When in receive mode, with packet framing enabled, the device is always ready to receive data transmitted at any of the supported bit rates. This enables the implementation of mixed-rate systems in which different devices use different data rates. This also enables the implementation of dynamic data rate systems that use high data rates at shorter distances or in a low-moderate interference environment or both. It changes to lower data rates at longer distances or in high interference environments or both. Data Transmission Modes The radio supports two different data transmission modes: ■ In GFSK mode, data is transmitted at 1 Mbps, without any DSSS ■ In DSSS mode eight bits (8DR, 32 chip) are encoded in each derived code symbol transmitted, resulting in effective 250 kbps data rate. 32 chip Pseudo Noise (PN) codes are supported. The two data transmission modes apply to the data after the SOP. In particular the length, data, and CRC16 are all sent in the same mode. In general, DSSS reduce packet error rate in any environment. Microcontroller Function The MCU function is an 8-bit Flash-programmable microcontroller. The instruction set is optimized specifically for HID and a variety of other embedded applications. The MCU function has up to 8 Kbytes of Flash for user’s code and up to 256 bytes of RAM for stack space and user variables. In addition, the MCU function includes a Watchdog timer, a vectored interrupt controller, a 16-bit Free Running Timer, and 12-bit Programmable Interrupt Timer. The microcontroller has 15 GPIO pins grouped into multiple ports. With the exception of the four radio function GPIOs, each GPIO port supports high impedance inputs, configurable pull-up, open drain output, CMOS/TTL inputs and CMOS output. Up to two pins support programmable drive strength of up to 50 mA. Additionally, each I/O pin can be used to generate a GPIO interrupt to the microcontroller. Each GPIO port has its own GPIO interrupt vector with the exception of GPIO Port 0. GPIO Port 0 has two dedicated pins that have independent interrupt vectors (P0.3 - P0.4). The microcontroller features an internal oscillator. Backward Compatibility The CYRF69303 IC is fully interoperable with the main modes of the second generation Cypress radio SoC namely the CYRF6936, CYRF69103 and CYRF69213. CYRF69303 IC device may transmit data to or receive data from a second generation device, or both. Document Number: 001-66502 Rev. *D Page 4 of 70 CYRF69303 Pinouts Figure 1. 40-pin QFN pinout NC 31 P1.6 32 VIO 33 RST 34 P1.7 35 VDD_1.8 36 GND 37 P0.7 38 Vcc 40 VBAT0 39 Corner tabs P0.4 1 30 XOUT / GPIO XTAL 2 29 MISO / GPIO VCC 3 28 P1.5 / MOSI P0.3 4 P0.1 5 VBAT1 6 VCC 7 P2.1 8 VBAT2 9 27 IRQ / GPIO CYRF69303 PRoC LPstar 26 P1.4 / SCK 25 P1.3 / SS 24 P1.2 23 VDD_Micro 22 P1.1 * E-PAD Bottom Side RFBIAS 10 21 P1.0 20 NC 19 RESV 18 NC 17 NC 16 VCC 15 P2.0 14 NC 13 RFN 12 GND 11 RFP Pin Definitions Pin Name 1 P0.4 Individually configured GPIO Description 12 MHz crystal 2 XTAL 3, 7, 16, 40 VCC Connected to 2.7 V to 3.6 V supply, through 0.047 F bypass C. 4 P0.3 Individually configured GPIO 5 P0.1 Individually configured GPIO 6 Vbat1 Connect to 2.7 V to 3.6 V power supply, through 47 ohm series/1 F shunt C 8 P2.1 GPIO. Port 2 Bit 1 9 Vbat2 Connected to 2.7 V to 3.6 V main power supply, through 0.047 F bypass C 10 RFbias RF pin voltage reference 11 RFp Differential RF to or from antenna 12 GND GND 13 RFn Differential RF to or from antenna 14, 17, 18, 20 NC 15 P2.0 19 RESV GPIO Reserved. Must connect to GND 21 P1.0 / GPIO 1.0 / ISSP-SCLK ISSP-SCLK 22 P1.1 / GPIO 1.1 / ISSP-SDATA ISSP-SDATA 23 VDD_micro 24 P1.2 MCU supply connected to VCC, max CPU 12 MHz GPIO 25 P1.3 / nSS Slave Select 26 P1.4 / SCK SPI Clock Document Number: 001-66502 Rev. *D Page 5 of 70 CYRF69303 Pin Definitions (continued) Pin Name 27 IRQ 28 Description Radio Function Interrupt output, configure High, Low or as Radio GPIO P1.5 / MOSI MOSI pin from microcontroller function to radio function 29 MISO 3-wire SPI mode configured as Radio GPIO. In 4-wire SPI mode sends data to MCU function 30 XOUT Buffered CLK or Radio GPIO 31 NC 32 P1.6 Must be floating GPIO 33 VIO 2.7 V to 3.6 V to main power supply rail for Radio I/O 34 RST Radio Reset. Connected to VCC with 0.47 F. Must have a RST=HIGH event the very first time power is applied to the radio otherwise the state of the radio control registers is unknown 35 P1.7 GPIO 36 VDD1.8 37 GND Regulated logic bypass. Connected to 0.47 F to GND Must be connected to ground 38 P0.7 GPIO 39 Vbat0 Connected to 2.7 V to 3.6 V main power supply, through 0.047 F bypass C E-pad Must be connected to ground 41 42 Corner Tabs Do Not connect corner tabs Functional Block Overview Baseband and Framer All the blocks that make up the PRoC LPstar are presented in this section. The baseband and framer blocks provide the DSSS encoding and decoding, SOP generation and reception and CRC16 generation and checking, and EOP detection and length field. 2.4 GHz Radio Data Transmission Modes and Data Rates The radio transceiver is a dual conversion low IF architecture optimized for power and range/robustness. The radio employs channel matched filters to achieve high performance in the presence of interference. An integrated Power Amplifier (PA) provides up to 0 dBm transmit power, with an output power control range of 30 dB in six steps. The supply current of the device is reduced as the RF output power is reduced. The SoC supports two different data transmission modes: Table 1. Internal PA Output Power Step Table 32 chip Pseudo Noise (PN) codes are supported. The two data transmission modes apply to the data after the SOP. In particular the length, data, and CRC16 are all sent in the same mode. In general, DSSS reduce packet error rate in any environment. PA Setting Typical Output Power (dBm) 6 0 5 –5 4 –10 3 –15 2 –20 1 –25 0 –30 ■ In GFSK mode, data is transmitted at 1 Mbps, without any DSSS. ■ In DSSS mode eight bits (8DR, 32 chip) are encoded in each derived code symbol transmitted, resulting in effective 250 kbps data rate. Link Layer Modes SOP Packets begin with a two-symbol SoP marker. If framing is disabled then an SOP event is inferred whenever two successive correlations are detected. The SOP_CODE_ADR code used for the SOP is different from that used for the “body” of the packet, and if desired may be a different length. SOP must be configured to be the same length on both sides of the link. Frequency Synthesizer Length Before transmission or reception may commence, it is necessary for the frequency synthesizer to settle. The settling time varies depending on channel; 25 fast channels are provided with a maximum settling time of 100 s. Length field is the first eight bits after the SOP symbol, and is transmitted at the payload data rate. An EoP condition is inferred after reception of the number of bytes defined in the length field, plus two bytes for the CRC16. The “fast channels” (<100 s settling time) are every third frequency, starting at 2400 MHz up to and including 2472 MHz (that is, 0,3,6,9…….69 and 72). Document Number: 001-66502 Rev. *D Page 6 of 70 CYRF69303 CRC16 CRC16 detects the following errors: The device may be configured to append a 16-bit CRC16 to each packet. The CRC16 uses the USB CRC polynomial with the added programmability of the seed. If enabled, the receiver verifies the calculated CRC16 for the payload data against the received value in the CRC16 field. The starting value for the CRC16 calculation is configurable, and the CRC16 transmitted may be calculated using either the loaded seed value or a zero seed; the received data CRC16 is checked against both the configured and zero CRC16 seeds. ■ Any one bit in error ■ Any two bits in error (no matter how far apart, which column, and so on) ■ Any odd number of bits in error (no matter where they are) ■ An error burst as wide as the checksum itself Figure 2 shows an example packet with SOP, CRC16 and lengths fields enabled. Figure 2. Example Default Packet Format 2nd Framing Symbol* Preamble N*16us Preamble SOP1 1st Framing Symbol* SOP2 Length <== P a y l o a d ==> CRC 16 Packet length 1 Byte Period *Note: 32 us Packet Buffers and Radio Configuration Registers Packet data and configuration registers are accessed through the SPI interface. All configuration registers are directly addressed through the address field in the SPI packet. Configuration registers are provided to allow configuration of DSSS PN codes, data rate, operating mode, interrupt masks, interrupt status, and others. Packet Buffers All data transmission and reception use the 16-byte packet buffers: one for transmission and one for reception. The transmit buffer allows a complete packet of up to 16 bytes of payload data to be loaded in one burst SPI transaction, and then transmitted with no further MCU intervention. Similarly, the receive buffer allows an entire packet of payload data up to 16 bytes to be received with no firmware intervention required until packet reception is complete. The CYRF69303 IC supports packet length of up to 40 bytes; interrupts are provided to allow an MCU to use the transmit and receive buffers as FIFOs. When transmitting a packet longer than 16 bytes, the MCU can load 16 bytes initially, and add further bytes to the transmit buffer as transmission of data creates space in the buffer. Similarly, when receiving packets longer than 16 bytes, the MCU must fetch received data from the FIFO periodically during packet reception to prevent it from overflowing. Auto Transaction Sequencer (ATS) The CYRF69303 IC provides automated support for transmission and reception of acknowledged data packets. When transmitting a data packet, the device automatically starts the crystal and synthesizer, enters transmit mode, transmits the packet in the transmit buffer, and then automatically switches to receive mode and waits for a handshake packet — and then Document Number: 001-66502 Rev. *D automatically reverts to sleep mode or idle mode when either an ACK packet is received, or a time out period expires. Similarly, when receiving in transaction mode, the device waits in receive mode for a valid packet to be received, then automatically transitions to transmit mode, transmits an ACK packet, and then switches back to receive mode to await the next packet. The contents of the packet buffers are not affected by the transmission or reception of ACK packets. In each case, the entire packet transaction takes place without any need for MCU firmware action; to transmit data the MCU simply needs to load the data packet to be transmitted, set the length, and set the TX GO bit. Similarly, when receiving packets in transaction mode, firmware simply needs to retrieve the fully received packet in response to an interrupt request indicating reception of a packet. Interrupts The radio function provides an interrupt (IRQ) output, which is configurable to indicate the occurrence of various different events. The IRQ pin may be programmed to be either active high or active low, and be either a CMOS or open drain output. The radio function features three sets of interrupts: transmit, receive, and system interrupts. These interrupts all share a single pin (IRQ), but can be independently enabled/disabled. In transmit mode, all receive interrupts are automatically disabled, and in receive mode all transmit interrupts are automatically disabled. However, the contents of the enable registers are preserved when switching between transmit and receive modes. If more than one radio interrupt is enabled at any time, it is necessary to read the relevant status register to determine which event caused the IRQ pin to assert. Even when an interrupt source is disabled, the status of the condition that would otherwise cause an interrupt can be determined by reading the appropriate status register. It is therefore possible to use the devices without making use of the IRQ pin by polling the status register(s) to wait for an event, rather than using the IRQ pin. Page 7 of 70 CYRF69303 Clocks A 12 MHz crystal (30 ppm or better) is directly connected between XTAL and GND without the need for external capacitors. A digital clock out function is provided, with selectable output frequencies of 0.75, 1.5, 3, 6, or 12 MHz. This output may be used to clock an external microcontroller (MCU) or ASIC. This output is enabled by default, but may be disabled. The requirements for the crystal to be directly connected to XTAL pin and GND are: ■ Nominal Frequency: 12 MHz ■ Operating Mode: Fundamental Mode ■ Resonance Mode: Parallel Resonant ■ Frequency Initial Stability: ±30 ppm ■ Series Resistance: <60 ohms ■ Load Capacitance: 10 pF ■ Drive Level: l00 W The MCU function features an internal oscillator. The clock generator provides the 12 MHz and 24 MHz clocks that remain internal to the microcontroller. at the start and at the end of an event, then calculating the difference between the two values. Power Management The operating voltage of the device is 2.7 V to 3.6 V DC, which is applied to VCC and VBAT pins. The device can be shut down to a fully static sleep mode by writing to the FRC END = 1 and END STATE = 000 bits in the XACT_CFG_ADR register over the SPI interface. The device enters sleep mode within 35 µs after the last SCK positive edge at the end of this SPI transaction. Alternatively, the device may be configured to automatically enter sleep mode after completing the packet transmission or reception. When in sleep mode, the on-chip oscillator is stopped, but the SPI interface remains functional. The device wakes from sleep mode automatically when the device is commanded to enter transmit or receive mode. When resuming from sleep mode, there is a short delay while the oscillator restarts. The device can be configured to assert the IRQ pin when the oscillator has stabilized. The following Figure 3 is an example of the circuit used when the supply voltage is always above 2.7 V. This could be three 1.5 V battery cells in series along with a linear regulator, or some similar power source. Figure 4 on page 9 shows an example of using an external boost to supply power to the device. GPIO Interface The MCU function features up to 15 general-purpose I/O (GPIO) pins.The I/O pins are grouped into three ports (Port 0 to 2). The pins on Port 0 and Port 1 may each be configured individually while the pins on Port 2 may only be configured as a group. Each GPIO port supports high-impedance inputs, configurable pull-up, open drain output, CMOS/TTL inputs, and CMOS output with up to two pins that support programmable drive strength of up to 50 mA sink current. Additionally, each I/O pin can be used to generate a GPIO interrupt to the microcontroller. Each GPIO port has its own GPIO interrupt vector with the exception of GPIO Port 0. GPIO Port 0 has three dedicated pins that have independent interrupt vectors (P0.1, P0.3–P0.4). Figure 3. Example Circuit - Linear Regulator VCC 0.047µF 0.047µF 0.047µF 0.047µF 0.047µF 0.047µF 0.047µF 0.047µF VCC1 VCC2 VCC3 VCC4 VIO VBat0 VBat1 The power-on reset (POR) circuit detects logic when power is applied to the device, resets the logic to a known state, and begins executing instructions at Flash address 0x0000. When power falls below a programmable trip voltage, it generates reset or may be configured to generate interrupt. VBat2 Power-on Reset Vcc VDD_MICRO CYRF69303 Timers Document Number: 001-66502 Rev. *D 0.1µF GND The free-running 16-bit timer provides two interrupt sources: the programmable interval timer with 1 s resolution and the 1.024 ms outputs. The timer can be used to measure the duration of an event under firmware control by reading the timer Page 8 of 70 CYRF69303 SPI Interface Figure 4. Example Circuit - External Boost Converter VCC VBat External DC-DC Boost Converter 1 Ohm 1% 10µF 6.3V 47 Ohm 0.047µF Three-Wire SPI Interface 0.047µF 1µF 6.3V 0.047µF 0.047µF 0.047µF VCC1 VCC2 VCC3 VCC4 VIO VBat0 VBat1 VBat2 0.047µF Vcc VDD_MICRO The SPI interface between the MCU function and the radio function is a 3-wire SPI Interface. The three pins are Master Out Slave In (MOSI), Serial Clock (SCK), and Slave Select (SS). There is an alternate 4-wire MISO Interface that requires the connection of two external pins. The SPI interface is controlled by configuring the SPI Configure Register. (SPICR Addr: 0x3D). CYRF69303 GND 0.1µF The radio function receives a clock from the MCU function on the SCK pin. The MOSI pin is multiplexed with the MISO pin. Bidirectional data transfer takes place between the MCU function and the radio function through this multiplexed MOSI pin. When using this mode the user firmware must ensure that the MOSI pin on the MCU function is in a high impedance state, except when the MCU is actively transmitting data. Firmware must also control the direction of data flow and switch directions between MCU function and radio function by setting the SWAP bit [Bit 7] of the SPI Configure Register. The SS pin is asserted before initiating a data transfer between the MCU function and the radio function. The IRQ function may be optionally multiplexed with the MOSI pin; when this option is enabled the IRQ function is not available while the SS pin is low. When using this configuration, user firmware must ensure that the MOSI function on MCU function is in a high-impedance state whenever SS is high. MOSI SCK nSS Figure 5. Three-Wire SPI Mode Low Noise Amplifier (LNA) and Received Signal Strength Indication (RSSI) The gain of the receiver may be controlled directly by clearing the AGC EN bit and writing to the low noise amplifier (LNA) bit of the RX_CFG_ADR register. When the LNA bit is cleared, the receiver gain is reduced by approximately 20 dB, allowing accurate reception of very strong received signals (for example when operating a receiver very close to the transmitter). An additional 20 dB of receiver attenuation can be added by setting the Attenuation (ATT) bit; this allows data reception to be limited to devices at very short ranges. Disabling AGC and enabling LNA is recommended unless receiving from a device using external PA. Radio Function MCU Function P1.5/MOSI MOSI/MISO multiplexed on one MOSI pin MOSI P1.4/SCK SCK P1.3/nSS nSS The RSSI register returns the relative signal strength of the on-channel signal power. When receiving, the device may be configured to automatically measure and store the relative strength of the signal being received as a 5-bit value. When enabled, an RSSI reading is taken and may be read through the SPI interface. An RSSI reading is taken automatically when the start of a packet is detected. In addition, a new RSSI reading is taken every time the previous reading is read from the RSSI register, allowing the background RF energy level on any channel to be easily measured when RSSI is read when no signal is being received. A new reading can occur as fast as once every 12 s. Document Number: 001-66502 Rev. *D Four-Wire SPI Interface The four-wire SPI communications interface consists of MOSI, MISO, SCK, and SS. The device receives SCK from the MCU function on the SCK pin. Data from the MCU function is shifted in on the MOSI pin. Data to the MCU function is shifted out on the MISO pin. The active low SS pin must be asserted for the two functions to communicate. The IRQ function may be optionally multiplexed with the MOSI pin; when this option is enabled the IRQ function is not available while the SS pin is low. When using this configuration, user firmware must ensure that the MOSI function on MCU function is in a high-impedance state whenever SS is high. Page 9 of 70 CYRF69303 The INC bit helps to read or write consecutive bytes from contiguous memory locations in a single burst mode operation. If Slave Select is asserted and INC = 0, then the MCU function reads/writes the bytes in the same register in burst mode, but if it is a register file then it reads/writes the bytes in that register file. Radio Function MCU Function P1.6/MISO If Slave Select is asserted and INC = 1, then the master MCU function reads a byte from the radio, the address is incremented by a byte location, and then the byte at that location is read, and so on. nSS MOSI SCK Figure 6. Four-Wire SPI Mode P1.5/MOSI MOSI P1.4/SCK SCK P1.3/nSS nSS MISO The SPI interface between the radio function and the MCU is not dependent on the internal 12 MHz oscillator of the radio. Therefore, radio function registers can be read from or written into while the radio is in sleep mode. SPI I/O Voltage References The SPI interfaces between MCU function and the radio and the IRQ and RST have a separate voltage reference VIO. For CYRF69303 VIO is normally set to VCC. SPI Connects to External Devices This connection is external to the PRoC LPstar Chip SPI Communication and Transactions The SPI transactions can be single byte or multi-byte. The MCU function initiates a data transfer through a Command/Address byte. The following bytes are data bytes. The SPI transaction format is shown in Figure 5. The three SPI wires, MOSI, SCK, and SS are also drawn out of the package as external pins to allow the user to interface their own external devices (such as optical sensors and others) through SPI. The radio function also has its own SPI wires MISO and IRQ, which can be used to send data back to the MCU function or send an interrupt request to the MCU function. They can also be configured as GPIO pins. The DIR bit specifies the direction of data transfer. 0 = Master reads from slave. 1 = Master writes to slave. Table 2. SPI Transaction Format Byte 1 Bit # Bit Name Byte 1+N 7 6 [5:0] [7:0] DIR INC Address Data Document Number: 001-66502 Rev. *D Page 10 of 70 CYRF69303 CPU Architecture The Accumulator Register (CPU_A) is the general-purpose register that holds the results of instructions that specify any of the source addressing modes. This family of microcontrollers is based on a high-performance, 8-bit, Harvard architecture microprocessor. Five registers control the primary operation of the CPU core. These registers are affected by various instructions, but are not directly accessible through the register space by the user. The Index Register (CPU_X) holds an offset value that is used in the indexed addressing modes. Typically, this is used to address a block of data within the data memory space. The Stack Pointer Register (CPU_SP) holds the address of the current top-of-stack in the data memory space. It is affected by the PUSH, POP, LCALL, CALL, RETI, and RET instructions, which manage the software stack. It can also be affected by the SWAP and ADD instructions. Table 3. CPU Registers and Register Name Register Register Name Flags CPU_F Program Counter CPU_PC Accumulator CPU_A Stack Pointer CPU_SP Index CPU_X The Flag Register (CPU_F) has three status bits: Zero Flag bit [1]; Carry Flag bit [2]; Supervisory State bit [3]. The Global Interrupt Enable bit [0] is used to globally enable or disable interrupts. The user cannot manipulate the Supervisory State status bit [3]. The flags are affected by arithmetic, logic, and shift operations. The manner in which each flag is changed is dependent upon the instruction being executed (for example, AND, OR, XOR). See Table 20 on page 16. The 16-bit Program Counter Register (CPU_PC) allows for direct addressing of the full eight Kbytes of program memory space. CPU Registers Flags Register The Flags Register can only be set or reset with logical instruction. Table 4. CPU Flags Register (CPU_F) [R/W] Bit # 7 Field 6 5 4 3 2 1 0 XIO Super Carry Zero Global IE Read/Write – Reserved – – R/W R RW RW RW Default 0 0 0 0 0 0 1 0 Bits 7:5 Bit 4 Reserved XIO Set by the user to select between the register banks. 0 = Bank 0 1 = Bank 1 Bit 3 Super Indicates whether the CPU is executing user code or Supervisor Code (This code cannot be accessed directly by the user). 0 = User Code 1 = Supervisor Code Bit 2 Carry Set by CPU to indicate whether there has been a carry in the previous logical/arithmetic operation. 0 = No Carry 1 = Carry Bit 1 Zero Set by CPU to indicate whether there has been a zero result in the previous logical/arithmetic operation. 0 = Not Equal to Zero 1 = Equal to Zero Bit 0 Global IE Determines whether all interrupts are enabled or disabled. 0 = Disabled 1 = Enabled Note This register is readable with explicit address 0xF7. The OR F, expr and AND F, expr must be used to set and clear the CPU_F bits. Document Number: 001-66502 Rev. *D Page 11 of 70 CYRF69303 Accumulator Register Table 5. CPU Accumulator Register (CPU_A) Bit # 7 6 5 Field 4 3 2 1 0 CPU Accumulator [7:0] Read/Write – – – – – – – – Default 0 0 0 0 0 0 0 0 Bits 7:0 CPU Accumulator [7:0] 8-bit data value holds the result of any logical/arithmetic instruction that uses a source addressing mode. Index Register Table 6. CPU X Register (CPU_X) Bit # 7 6 5 4 Field 3 2 1 0 X [7:0] Read/Write – – – – – – – – Default 0 0 0 0 0 0 0 0 2 1 0 Bits 7:0 X [7:0] 8-bit data value holds an index for any instruction that uses an indexed addressing mode. Stack Pointer Register Table 7. CPU Stack Pointer Register (CPU_SP) Bit # 7 6 5 4 Field 3 Stack Pointer [7:0] Read/Write – – – – – – – – Default 0 0 0 0 0 0 0 0 4 3 2 1 0 Bits 7:0 Stack Pointer [7:0] 8-bit data value holds a pointer to the current top-of-stack. CPU Program Counter High Register Table 8. CPU Program Counter High Register (CPU_PCH) Bit # 7 6 5 Field Program Counter [15:8] Read/Write – – – – – – – – Default 0 0 0 0 0 0 0 0 4 3 2 1 0 Bits 7:0 Program Counter [15:8] 8-bit data value holds the higher byte of the program counter. CPU Program Counter Low Register Table 9. CPU Program Counter Low Register (CPU_PCL) Bit # 7 6 5 Field Program Counter [7:0] Read/Write – – – – – – – – Default 0 0 0 0 0 0 0 0 Bit 7:0 Program Counter [7:0] 8-bit data value holds the lower byte of the program counter. Document Number: 001-66502 Rev. *D Page 12 of 70 CYRF69303 Addressing Modes Source Indexed Examples of the different addressing modes are discussed in this section and example code is given. Source Immediate The result of an instruction using this addressing mode is placed in the A register, the F register, the SP register, or the X register, which is specified as part of the instruction opcode. Operand 1 is an immediate value that serves as a source for the instruction. Arithmetic instructions require two sources. Instructions using this addressing mode are two bytes in length. The result of an instruction using this addressing mode is placed in either the A register or the X register, which is specified as part of the instruction opcode. Operand 1 is added to the X register forming an address that points to a location in either the RAM memory space or the register space that is the source for the instruction. Arithmetic instructions require two sources; the second source is the A register or X register specified in the opcode. Instructions using this addressing mode are two bytes in length. Table 12. Source Indexed Opcode Table 10. Source Immediate Opcode Operand 1 Instruction Immediate Value Examples ADD A, Source Index Examples ADD A, [X+7] 7 In this case, the immediate value of 7 is added with the Accumulator, and the result is placed in the Accumulator. MOV X, 8 In this case, the immediate value of 8 is moved to the X register. AND F, 9 In this case, the immediate value of 9 is logically ANDed with the F register and the result is placed in the F register. Source Direct The result of an instruction using this addressing mode is placed in either the A register or the X register, which is specified as part of the instruction opcode. Operand 1 is an address that points to a location in either the RAM memory space or the register space that is the source for the instruction. Arithmetic instructions require two sources; the second source is the A register or X register specified in the opcode. Instructions using this addressing mode are two bytes in length. Examples ADD A, X, In this case, the value in the memory location at address X + 7 is added with the Accumulator, and the result is placed in the Accumulator. REG[X+8] In this case, the value in the register space at address X + 8 is moved to the X register. Destination Direct The result of an instruction using this addressing mode is placed within either the RAM memory space or the register space. Operand 1 is an address that points to the location of the result. The source for the instruction is either the A register or the X register, which is specified as part of the instruction opcode. Arithmetic instructions require two sources; the second source is the location specified by Operand 1. Instructions using this addressing mode are two bytes in length. Table 13. Destination Direct Operand 1 Destination Address Operand 1 Source Address [7] X, Instruction Opcode Instruction MOV Opcode Table 11. Source Direct MOV Operand 1 Instruction Examples ADD [7], A In this case, the value in the memory location at address 7 is added with the Accumulator, and the result is placed in the memory location at address 7. The Accumulator is unchanged. A In this case, the Accumulator is moved to the register space location at address 8. The Accumulator is unchanged. In this case, the value in the RAM memory location at address 7 is added with the Accumulator, and the result is placed in the Accumulator. REG[8] In this case, the value in the register space at address 8 is moved to the X register. Document Number: 001-66502 Rev. *D MOV REG[8], Page 13 of 70 CYRF69303 Destination Indexed Destination Indexed Source Immediate The result of an instruction using this addressing mode is placed within either the RAM memory space or the register space. Operand 1 is added to the X register forming the address that points to the location of the result. The source for the instruction is the A register. Arithmetic instructions require two sources; the second source is the location specified by Operand 1 added with the X register. Instructions using this addressing mode are two bytes in length. The result of an instruction using this addressing mode is placed within either the RAM memory space or the register space. Operand 1 is added to the X register to form the address of the result. The source for the instruction is Operand 2, which is an immediate value. Arithmetic instructions require two sources; the second source is the location specified by Operand 1 added with the X register. Instructions using this addressing mode are three bytes in length. Table 14. Destination Indexed Table 16. Destination Indexed Source Immediate Opcode Instruction Example ADD [X+7], Operand 1 Destination Index A In this case, the value in the memory location at address X+7 is added with the Accumulator, and the result is placed in the memory location at address x+7. The Accumulator is unchanged. Opcode Instruction MOV Table 15. Destination Direct Source Immediate Opcode Instruction Examples ADD [7], MOV REG[8], Operand 1 Destination Address Operand 2 Immediate Value REG[X+8], 6 In this case, value in the memory location at address 7 is added to the immediate value of 5, and the result is placed in the memory location at address 7. In this case, the immediate value of 6 is moved into the register space location at address 8. Document Number: 001-66502 Rev. *D Operand 2 Immediate Value 5 In this case, the value in the memory location at address X+7 is added with the immediate value of 5 and the result is placed in the memory location at address X+7. 6 In this case, the immediate value of 6 is moved into the location in the register space at address X+8. Destination Direct Source Direct The result of an instruction using this addressing mode is placed within the RAM memory. Operand 1 is the address of the result. Operand 2 is an address that points to a location in the RAM memory that is the source for the instruction. This addressing mode is only valid on the MOV instruction. The instruction using this addressing mode is three bytes in length. Table 17. Destination Direct Source Direct Opcode 5 Destination Index Examples ADD [X+7], Destination Direct Source Immediate The result of an instruction using this addressing mode is placed within either the RAM memory space or the register space. Operand 1 is the address of the result. The source for the instruction is Operand 2, which is an immediate value. Arithmetic instructions require two sources; the second source is the location specified by Operand 1. Instructions using this addressing mode are three bytes in length. Operand 1 Instruction Example MOV [7], Operand 1 Destination Address Operand 2 Source Address [8] In this case, the value in the memory location at address 8 is moved to the memory location at address 7. Page 14 of 70 CYRF69303 Source Indirect Post Increment Destination Indirect Post Increment The result of an instruction using this addressing mode is placed in the Accumulator. Operand 1 is an address pointing to a location within the memory space, which contains an address (the indirect address) for the source of the instruction. The indirect address is incremented as part of the instruction execution. This addressing mode is only valid on the MVI instruction. The instruction using this addressing mode is two bytes in length. Refer to the PSoC Designer: Assembly Language User Guide for further details on MVI instruction. The result of an instruction using this addressing mode is placed within the memory space. Operand 1 is an address pointing to a location within the memory space, which contains an address (the indirect address) for the destination of the instruction. The indirect address is incremented as part of the instruction execution. The source for the instruction is the Accumulator. This addressing mode is only valid on the MVI instruction. The instruction using this addressing mode is two bytes in length. Table 19. Destination Indirect Post Increment Table 18. Source Indirect Post Increment Opcode Instruction Example MVI A, Operand 1 Opcode Instruction Operand 1 Destination Address Address Source Address Address Example MVI [8], [8] In this case, the value in the memory location at address 8 is an indirect address. The memory location pointed to by the indirect address is moved into the Accumulator. The indirect address is then incremented. Document Number: 001-66502 Rev. *D A In this case, the value in the memory location at address 8 is an indirect address. The Accumulator is moved into the memory location pointed to by the indirect address. The indirect address is then incremented. Page 15 of 70 CYRF69303 Instruction Set Summary The instruction set is summarized in Table 20 numerically and serves as a quick reference. If more information is needed, the Instruction Set Summary tables are described in detail in the PSoC Designer Assembly Language User Guide (available on www.cypress.com). Cycles Bytes Opcode Hex Cycles Bytes Opcode Hex Cycles Bytes Opcode Hex Table 20. Instruction Set Summary Sorted Numerically by Opcode Order[1, 2] 00 15 1 SSC 2D 8 2 OR [X+expr], A Z 5A 5 2 MOV [expr], X 01 4 2 ADD A, expr C, Z 2E 9 3 OR [expr], expr Z 5B 4 1 MOV A, X 02 6 2 ADD A, [expr] C, Z 2F 10 3 OR [X+expr], expr Z 5C 4 1 MOV X, A 03 7 2 ADD A, [X+expr] C, Z 30 9 1 HALT 5D 6 2 MOV A, reg[expr] Z 04 7 2 ADD [expr], A C, Z 31 4 2 XOR A, expr Z 5E 7 2 MOV A, reg[X+expr] Z 05 8 2 ADD [X+expr], A C, Z 32 6 2 XOR A, [expr] Z 5F 10 3 MOV [expr], [expr] 06 Instruction Format Flags Instruction Format Flags Instruction Format Flags Z 9 3 ADD [expr], expr C, Z 33 7 2 XOR A, [X+expr] Z 60 5 2 MOV reg[expr], A 07 10 3 ADD [X+expr], expr C, Z 34 7 2 XOR [expr], A Z 61 6 2 MOV reg[X+expr], A 08 4 1 PUSH A 35 8 2 XOR [X+expr], A Z 62 8 3 MOV reg[expr], expr 09 4 2 ADC A, expr C, Z 36 9 3 XOR [expr], expr Z 63 9 3 MOV reg[X+expr], expr 0A 6 2 ADC A, [expr] C, Z 37 10 3 XOR [X+expr], expr Z 64 4 1 ASL A C, Z 0B 7 2 ADC A, [X+expr] C, Z 38 5 2 ADD SP, expr 65 7 2 ASL [expr] C, Z 0C 7 2 ADC [expr], A C, Z 39 5 2 CMP A, expr 8 2 ASL [X+expr] C, Z 0D 8 2 ADC [X+expr], A C, Z 3A 7 2 CMP A, [expr] if (A=B) Z=1 66 if (A<B) C=1 67 4 1 ASR A C, Z 0E 9 3 ADC [expr], expr C, Z 3B 8 2 CMP A, [X+expr] 68 7 2 ASR [expr] C, Z 0F 10 3 ADC [X+expr], expr C, Z 3C 8 3 CMP [expr], expr 69 8 2 ASR [X+expr] C, Z 10 4 1 PUSH X 3D 9 3 CMP [X+expr], expr 6A 4 1 RLC A C, Z 11 4 2 SUB A, expr C, Z 3E 10 2 MVI A, [ [expr]++ ] 6B 7 2 RLC [expr] C, Z 12 6 2 SUB A, [expr] C, Z 3F 10 2 MVI [ [expr]++ ], A 6C 8 2 RLC [X+expr] C, Z 13 7 2 SUB A, [X+expr] C, Z 40 4 1 NOP 6D 4 1 RRC A C, Z 14 7 2 SUB [expr], A C, Z 41 9 3 AND reg[expr], expr Z 6E 7 2 RRC [expr] C, Z 15 8 2 SUB [X+expr], A C, Z 42 10 3 AND reg[X+expr], expr Z 6F 8 2 RRC [X+expr] C, Z 16 9 3 SUB [expr], expr C, Z 43 9 3 OR reg[expr], expr Z 70 4 2 AND F, expr C, Z 17 10 3 SUB [X+expr], expr C, Z 44 10 3 OR reg[X+expr], expr Z 71 4 2 OR F, expr C, Z 18 5 1 POP A 45 9 3 XOR reg[expr], expr Z 72 4 2 XOR F, expr C, Z 19 4 2 SBB A, expr C, Z 46 10 3 XOR reg[X+expr], expr Z 73 4 1 CPL A Z 1A 6 2 SBB A, [expr] C, Z 47 8 3 TST [expr], expr Z 74 4 1 INC A C, Z Z Z 1B 7 2 SBB A, [X+expr] C, Z 48 9 3 TST [X+expr], expr Z 75 4 1 INC X C, Z 1C 7 2 SBB [expr], A C, Z 49 9 3 TST reg[expr], expr Z 76 7 2 INC [expr] C, Z 1D 8 2 SBB [X+expr], A C, Z 4A 10 3 TST reg[X+expr], expr Z 77 8 2 INC [X+expr] C, Z 1E 9 3 SBB [expr], expr C, Z 4B 5 1 SWAP A, X Z 78 4 1 DEC A C, Z 1F 10 3 SBB [X+expr], expr C, Z 4C 7 2 SWAP A, [expr] Z 79 4 1 DEC X C, Z 20 5 1 POP X 4D 7 2 SWAP X, [expr] 7A 7 2 DEC [expr] C, Z 21 4 2 AND A, expr Z 4E 5 1 SWAP A, SP 7B 8 2 DEC [X+expr] C, Z 22 6 2 AND A, [expr] Z 4F 4 1 MOV X, SP 7C 13 3 LCALL 23 7 2 AND A, [X+expr] Z 50 4 2 MOV A, expr Z 7D 7 3 LJMP 24 7 2 AND [expr], A Z 51 5 2 MOV A, [expr] Z 7E 10 1 RETI 25 8 2 AND [X+expr], A Z 52 6 2 MOV A, [X+expr] Z 7F 8 1 RET 26 Z 9 3 AND [expr], expr Z 53 5 2 MOV [expr], A 8x 5 2 JMP 27 10 3 AND [X+expr], expr Z 54 6 2 MOV [X+expr], A 9x 11 2 CALL 28 11 1 ROMX Z 55 8 3 MOV [expr], expr Ax 5 2 JZ 29 4 2 OR A, expr Z 56 9 3 MOV [X+expr], expr Bx 5 2 JNZ 2A 6 2 OR A, [expr] Z 57 4 2 MOV X, expr Cx 5 2 JC 2B 7 2 OR A, [X+expr] Z 58 6 2 MOV X, [expr] Dx 5 2 JNC 2C 7 2 OR [expr], A Z 59 7 2 MOV X, [X+expr] Ex 7 2 JACC Fx 13 2 INDEX C, Z Z Notes 1. Interrupt routines take 13 cycles before execution resumes at interrupt vector table. 2. The number of cycles required by an instruction is increased by one for instructions that span 256-byte boundaries in the Flash memory space. Document Number: 001-66502 Rev. *D Page 16 of 70 CYRF69303 Memory Organization Flash Program Memory Organization Table 21. Program Memory Space with Interrupt Vector Table after reset 16-bit PC Address 0x0000 0x0004 0x0008 0x000C 0x0010 0x0014 0x0018 0x001C 0x0020 0x0024 0x0028 0x002C 0x0030 0x0034 0x0038 0x003C 0x0040 0x0044 0x0048 0x004C 0x0050 0x0054 0x0058 0x005C 0x0060 0x0064 0x0068 Program execution begins here after a reset POR Reserved SPI Transmitter Empty SPI Receiver Full GPIO Port 0 GPIO Port 1 INT1 Reserved Reserved Reserved Reserved Reserved 1 ms Interval Timer Programmable Interval Timer Reserved Reserved 16-bit Free Running Timer Wrap INT2 Reserved GPIO Port 2 Reserved Reserved Reserved Reserved Sleep Timer Program Memory begins here (if below interrupts not used, program memory can start lower) 0x1FFF Document Number: 001-66502 Rev. *D Page 17 of 70 CYRF69303 Data Memory Organization The MCU function provides up to 256 bytes of data RAM. Table 22. Data Memory Organization after reset Address 8-bit PSP 0x00 Top of RAM Memory Stack begins here and grows upward 0xFF Flash SROM This section describes the Flash block of the CYRF69303. Much of the user visible Flash functionality, including programming and security, are implemented in the M8C Supervisory Read Only Memory (SROM). CYRF69303 Flash has an endurance of 1000 cycles and 10-year data retention. The SROM holds code that is used to boot the part, calibrate circuitry, and perform Flash operations (Table 23 lists the SROM functions). The functions of the SROM may be accessed in normal user code or operating from Flash. The SROM exists in a separate memory space from user code. The SROM functions are accessed by executing the Supervisory System Call instruction (SSC), which has an opcode of 00h. Before executing the SSC, the M8C’s accumulator needs to be loaded with the desired SROM function code from Table 23. Undefined functions causes a HALT if called from user code. The SROM functions are executing code with calls; therefore, the functions require stack space. With the exception of Reset, all of the SROM functions have a parameter block in SRAM that must be configured before executing the SSC. Table 24 on page 19 lists all possible parameter block variables. The meaning of each parameter, with regards to a specific SROM function, is described later in this section. Flash Programming and Security All Flash programming is performed by code in the SROM. The registers that control the Flash programming are only visible to the M8C CPU when it is executing out of SROM. This makes it impossible to read, write, or erase the Flash by bypassing the security mechanisms implemented in the SROM. Customer firmware can only program the Flash through SROM calls. The data or code images can be sourced by way of any interface with the appropriate support firmware. This type of programming requires a ‘bootloader’ — a piece of firmware resident on the Flash. For safety reasons, this bootloader must not be over written during firmware rewrites. The Flash provides four auxiliary rows that are used to hold Flash block protection flags, boot time calibration values, configuration tables, and any device values. The routines for accessing these auxiliary rows are documented in the SROM section. The auxiliary rows are not affected by the device erase function. Table 23. SROM Function Codes Function Code Function Name Stack Space 00h SWBootReset 0 01h ReadBlock 7 02h WriteBlock 10 In-System Programming 03h EraseBlock 9 CYRF69303 enables this type of in-system programming by using the P1.0 and P1.1 pins as the serial programming mode interface. This allows an external controller to cause the CYRF69303 to enter serial programming mode and then to use the test queue to issue Flash access functions in the SROM. 05h EraseAll 11 06h TableRead 3 07h CheckSum 3 Document Number: 001-66502 Rev. *D Page 18 of 70 CYRF69303 Two important variables that are used for all functions are KEY1 and KEY2. These variables are used to help discriminate between valid SSCs and inadvertent SSCs. KEY1 must always have a value of 3Ah, while KEY2 must have the same value as the stack pointer when the SROM function begins execution. This is the Stack Pointer value when the SSC opcode is executed, plus three. If either of the keys do not match the expected values, the M8C halts (with the exception of the SWBootReset function). The following code puts the correct value in KEY1 and KEY2. The code starts with a halt, to force the program to jump directly into the setup code and not run into it. halt SSCOP: mov [KEY1], 3ah mov X, SP mov A, X add A, 3 mov [KEY2], A Table 24. SROM Function Parameters Variable Name SRAM Address Key1/Counter/Return Code 0,F8h second loop erases and then programs each protection block with zeros. SROM Function Descriptions All SROM functions are described in the following sections. SWBootReset Function The SROM function, SWBootReset, is the function that is responsible for transitioning the device from a reset state to running user code. The SWBootReset function is executed whenever the SROM is entered with an M8C accumulator value of 00h; the SRAM parameter block is not used as an input to the function. This happens, by design, after a hardware reset, because the M8C's accumulator is reset to 00h or when user code executes the SSC instruction with an accumulator value of 00h. The SWBootReset function does not execute when the SSC instruction is executed with a bad key value and a nonzero function code. A CYRF69303 device executes the HALT instruction if a bad value is given for either KEY1 or KEY2. The SWBootReset function verifies the integrity of the calibration data by way of a 16-bit checksum, before releasing the M8C to run user code. Key2/TMP 0,F9h BlockID 0,FAh ReadBlock Function Pointer 0,FBh Clock 0,FCh The ReadBlock function is used to read 64 contiguous bytes from Flash — a block. Mode 0,FDh Delay 0,FEh PCL 0,FFh The SROM also features Return Codes and Lockouts. Return Codes Return codes aid in the determination of success or failure of a particular function. The return code is stored in KEY1’s position in the parameter block. The CheckSum and TableRead functions do not have return codes because KEY1’s position in the parameter block is used to return other data. Table 25. SROM Return Codes Return Code Description 00h Success 01h Function not allowed due to level of protection on block 02h Software reset without hardware reset 03h Fatal error, SROM halted Read, write, and erase operations may fail if the target block is read or write protected. Block protection levels are set during device programming. The EraseAll function overwrites data in addition to leaving the entire user Flash in the erase state. The EraseAll function loops through the number of Flash macros in the product, executing the following sequence: erase, bulk program all zeros, erase. After all the user space in all the Flash macros are erased, a Document Number: 001-66502 Rev. *D The first thing this function does is to check the protection bits and determine if the desired BLOCKID is readable. If read protection is turned on, the ReadBlock function exits setting the accumulator and KEY2 back to 00h. KEY1 has a value of 01h, indicating a read failure. If read protection is not enabled, the function reads 64 bytes from the Flash using a ROMX instruction and store the results in SRAM using an MVI instruction. The first of the 64 bytes are stored in SRAM at the address indicated by the value of the POINTER parameter. When the ReadBlock completes successfully, the accumulator, KEY1 and KEY2, all have a value of 00h. Table 26. ReadBlock Parameters Name Address Description KEY1 0,F8h 3Ah KEY2 0,F9h Stack Pointer value, when SSC is executed BLOCKID 0,FAh Flash block number POINTER 0,FBh First of 64 addresses in SRAM where returned data must be stored WriteBlock Function The WriteBlock function is used to store data in the Flash. Data is moved 64 bytes at a time from SRAM to Flash using this function. The first thing the WriteBlock function does is to check the protection bits and determine if the desired BLOCKID is writable. If write protection is turned on, the WriteBlock function exits, setting the accumulator and KEY2 back to 00h. KEY1 has a value of 01h, indicating a write failure. The configuration of the WriteBlock function is straightforward. The BLOCKID of the Flash block, where the data is stored, must be determined and stored at SRAM address FAh. Page 19 of 70 CYRF69303 The SRAM address of the first of the 64 bytes to be stored in Flash must be indicated using the POINTER variable in the parameter block (SRAM address FBh). Finally, the CLOCK and DELAY values must be set correctly. The CLOCK value determines the length of the write pulse that is used to store the data in the Flash. The CLOCK and DELAY values are dependent on the CPU. Refer to ‘Clocking’ Section for additional information. Table 27. WriteBlock Parameters Name Address Description KEY1 0,F8h 3Ah KEY2 0,F9h Stack Pointer value, when SSC is executing BLOCK ID 0,FAh 8 KB Flash block number (00h–7Fh) 4 KB Flash block number (00h–3Fh) 3 KB Flash block number (00h–2Fh) POINTER 0,FBh First 64 addresses in SRAM where the data to be stored in Flash is located before calling WriteBlock CLOCK DELAY 0,FCh 0,FEh Clock Divider used to set the write Pulse width For a CPU speed of 12 MHz set to 56h EraseBlock Function The EraseBlock function is used to erase a block of 64 contiguous bytes in Flash. The first thing the EraseBlock function does is to check the protection bits and determine if the desired BLOCKID is writable. If write protection is turned on, the EraseBlock function exits, setting the accumulator and KEY2 back to 00h. KEY1 has a value of 01h, indicating a write failure. The EraseBlock function is only useful as the first step in programming. Erasing a block does not cause data in a block to be one hundred percent unreadable. If the objective is to obliterate data in a block, the best method is to perform an EraseBlock followed by a WriteBlock of all zeros. To setup the parameter block for the EraseBlock function, correct key values must be stored in KEY1 and KEY2. The block number to be erased must be stored in the BLOCKID variable and the CLOCK and DELAY values must be set based on the current CPU speed. Table 28. EraseBlock Parameters Name Address Description KEY1 0,F8h 3Ah KEY2 0,F9h Stack Pointer value when SSC is executed ProtectBlock Function The CYRF69303 device offers Flash protection on a block-by-block basis. Table 29 lists the protection modes available. In the table, ER and EW are used to indicate the ability to perform external reads and writes. For internal writes, IW is used. Internal reading is always permitted by way of the ROMX instruction. The ability to read by way of the SROM ReadBlock function is indicated by SR. The protection level is stored in two bits, according to Table 29. These bits are bit packed into the 64 bytes of the protection block. Therefore, each protection block byte stores the protection level for four Flash blocks. The bits are packed into a byte, with the lowest numbered block’s protection level stored in the lowest numbered bits. The first address of the protection block contains the protection level for blocks 0 through 3; the second address is for blocks 4 through 7. The 64th byte stores the protection level for blocks 252 through 255. Table 29. Protection Modes Mode Settings 00b SR ER EW IW 01b 10b 11b Description Marketing Unprotected Unprotected SR ER EW IW Read protect Factory upgrade SR ER EW IW Disable external Field upgrade write SR ER EW IW Disable internal Full protection write 7 6 Block n+3 5 4 Block n+2 3 2 Block n+1 1 0 Block n The level of protection is only decreased by an EraseAll, which places zeros in all locations of the protection block. To set the level of protection, the ProtectBlock function is used. This function takes data from SRAM, starting at address 80h, and ORs it with the current values in the protection block. The result of the OR operation is then stored in the protection block. The EraseBlock function does not change the protection level for a block. Because the SRAM location for the protection data is fixed and there is only one protection block per Flash macro, the ProtectBlock function expects very few variables in the parameter block to be set before calling the function. The parameter block values that must be set, besides the keys, are the CLOCK and DELAY values. Table 30. ProtectBlock Parameters Name Address Description KEY1 0,F8h 3Ah KEY2 0,F9h Stack Pointer value when SSC is executed BLOCKID 0,FAh Flash block number (00h–7Fh) CLOCK 0,FCh Clock Divider used to set the erase pulse width CLOCK 0,FCh Clock Divider used to set the write pulse width DELAY 0,FEh For a CPU speed of 12 MHz set to 56h DELAY 0,FEh For a CPU speed of 12 MHz set to 56h Document Number: 001-66502 Rev. *D Page 20 of 70 CYRF69303 EraseAll Function The EraseAll function performs a series of steps that destroy the user data in the Flash macros and resets the protection block in each Flash macro to all zeros (the unprotected state). The EraseAll function does not affect the three hidden blocks above the protection block in each Flash macro. The first of these four hidden blocks is used to store the protection table for its eight Kbytes of user data. An internal table holds the Silicon ID and returns the Revision ID. The Silicon ID is returned in SRAM, while the Revision ID is returned in the CPU_A and CPU_X registers. The Silicon ID is a value placed in the table by programming the Flash and is controlled by Cypress Semiconductor Product Engineering. The Revision ID is hard coded into the SROM. The Revision ID is discussed in more detail later in this section. The EraseAll function begins by erasing the user space of the Flash macro with the highest address range. A bulk program of all zeros is then performed on the same Flash macro, to destroy all traces of the previous contents. The bulk program is followed by a second erase that leaves the Flash macro in a state ready for writing. The erase, program, erase sequence is then performed on the next lowest Flash macro in the address space if it exists. Following the erase of the user space, the protection block for the Flash macro with the highest address range is erased. Following the erase of the protection block, zeros are written into every bit of the protection table. The next lowest Flash macro in the address space then has its protection block erased and filled with zeros. An internal table holds alternate trim values for the device and returns a one-byte internal revision counter. The internal revision counter starts out with a value of zero and is incremented each time one of the other revision numbers is not incremented. It is reset to zero each time one of the other revision numbers is incremented. The internal revision count is returned in the CPU_A register. The CPU_X register is always set to FFh when trim values are read. The BLOCKID value, in the parameter block, is used to indicate which table must be returned to the user. Only the three least significant bits of the BLOCKID parameter are used by the TableRead function for the CYRF69303. The upper five bits are ignored. When the function is called, it transfers bytes from the table to SRAM addresses F8h–FFh. The end result of the EraseAll function is that all user data in the Flash is destroyed and the Flash is left in an unprogrammed state, ready to accept one of the various write commands. The protection bits for all user data are also reset to the zero state. The M8C’s A and X registers are used by the TableRead function to return the die’s Revision ID. The Revision ID is a 16-bit value hard coded into the SROM that uniquely identifies the die’s design. The parameter block values that must be set, besides the keys, are the CLOCK and DELAY values. Checksum Function Table 31. EraseAll Parameters Name Address Description KEY1 0,F8h 3Ah KEY2 0,F9h Stack Pointer value when SSC is executed CLOCK 0,FCh Clock Divider used to set the write pulse width DELAY 0,FEh For a CPU speed of 12 MHz set to 56h TableRead Function The TableRead function gives the user access to part specific data stored in the Flash during manufacturing. It also returns a Revision ID for the die (not to be confused with the Silicon ID). Table 32. Table Read Parameters Name Address The Checksum function calculates a 16-bit checksum over a user specifiable number of blocks, within a single Flash macro (Bank) starting from block zero. The BLOCKID parameter is used to pass in the number of blocks to calculate the checksum over. A BLOCKID value of 1 calculates the checksum of only block 0, while a BLOCKID value of 0 calculates the checksum of all 256 user blocks. The 16-bit checksum is returned in KEY1 and KEY2. The parameter KEY1 holds the lower eight bits of the checksum and the parameter KEY2 holds the upper eight bits of the checksum. The checksum algorithm executes the following sequence of three instructions over the number of blocks times 64 to be checksummed. romx add [KEY1], A adc [KEY2], 0 Table 33. Checksum Parameters Name Description Address Description KEY1 0,F8h 3Ah 0,F9h Stack Pointer value when SSC is executed 0,FAh Number of Flash blocks to calculate checksum on KEY1 0,F8h 3Ah KEY2 KEY2 0,F9h Stack Pointer value when SSC is executed BLOCKID BLOCKID 0,FAh Table number to read The table space for the CYRF69303 is simply a 64 byte row broken up into eight tables of eight bytes. The tables are numbered zero through seven. All user and hidden blocks in the CYRF69303 consist of 64 bytes. Document Number: 001-66502 Rev. *D Page 21 of 70 CYRF69303 Clocking The CYRF69303 internal oscillator outputs two frequencies, the Internal 24 MHz Oscillator and the 32 kHz Low power Oscillator. The Internal 24 MHz Oscillator is designed such that it may be trimmed to an output frequency of 24 MHz over temperature and voltage variation. The Internal 24 MHz Oscillator accuracy is 24 MHz –22% to +10% (between 0 °C–70 °C). No external components are required to achieve this level of accuracy. Firmware is responsible for selecting the correct trim values from the User row to match the power supply voltage in the end application and writing the values to the trim registers IOSCTR and LPOSCTR. The internal low speed oscillator of nominally 32 kHz provides a slow clock source for the CYRF69303 in suspend mode. This is used to generate a periodic wakeup interrupt and provide a clock to sequential logic during power-up and power-down events when the main clock is stopped. In addition, this oscillator can also be used as a clocking source for the Interval Timer clock (ITMRCLK) and Capture Timer clock (TCAPCLK). The 32 kHz Low power Oscillator can operate in low power mode or can provide a more accurate clock in normal mode. The Internal 32 kHz Low power Oscillator accuracy ranges from –53.12% to +56.25%. The 32 kHz low power oscillator can be calibrated against the internal 24 MHz oscillator or another timing source if desired. CYRF69303 provides the ability to load new trim values for the 24 MHz oscillator based on voltage. This allows VDD to be monitored and have firmware trim the oscillator based on voltage present. The IOSCTR register is used to set trim values for the 24 MHz oscillator. CYRF69303 is initialized with 3.30 V trim values at power on, then firmware is responsible for transferring the correct set of trim values to the trim registers to match the application’s actual Vdd. The 32 kHz oscillator generally does not require trim adjustments versus voltage but trim values for the 32 kHz are also stored in Supervisory ROM. Figure 7. SROM Table F8h Table 0 Silicon ID [15-8] F9h FAh FBh FCh FDh FEh FFh Silicon ID [7-0] lid ing Va rat n pe io O Reg Table 1 24 MHz IOSCTR at 3.30V Table 2 32 kHz 32 kHz 32 kHz 24 MHz IOSCTR at 3.00V 24 MHz IOSCTR at 2.85V 24 MHz IOSCTR at 2.70V 32 kHz Table 3 LPOSCTR LPOSCTR LPOSCTR LPOSCTR at 3.30V at 3.00V at 2.85V at 2.70V Table 4 Table 5 Table 6 Table 7 To improve the accuracy of the IMO, new trim values are loaded based on supply voltage to the part. For this, firmware needs to make modifications to two registers: 1. The internal oscillator trim register at location 0x34. 2. The gain register at location 0x38. Document Number: 001-66502 Rev. *D Page 22 of 70 CYRF69303 Trim values for the IOSCTR register: The trim values are stored in SROM tables in the part as shown in Figure 7 on page 22. The trim values are read out from the part based on voltage settings and written to the IOSCTR register at location 0x34. The following pseudo code shows how this is done. _main: mov A, 2 mov [SSC_BLOCKID], A Call SROM operation to read the SROM table (Refer to Table 32 on page 21 in the section SROM on page 18) //After this command is executed, the trim values for 3.3, 3.0, 2.85 and 2.7 are stored at locations FC through FF in the RAM. SROM calls are explained in the previous section of this datasheet ; mov A, [FCh] // trim values for 3.3 V mov A, [FDh] // trim values for 3.0 V ; mov A, [FEh] // trim values for 2.85 V ; mov A, [FFh] // trim values for 2.70 V mov reg[IOSCTR],A // Loading IOSCTR with trim values for 3.0 V .terminate: jmp .terminate SROM Table Read Description The Silicon IDs for CYRF69303 devices are stored in SROM tables in the part, as shown in Figure 7. The Silicon ID can be read out from the part using SROM Table reads. This is demonstrated in the following pseudo code. As mentioned in the section SROM on page 18, the SROM variables occupy address F8h through FFh in the SRAM. Each of the variables and their definition is given in section SROM on page 18. AREA SSCParmBlkA(RAM,ABS) org F8h // Variables are defined starting at address F8h SSC_KEY1: SSC_RETURNCODE: blk 1 SSC_KEY2 : blk 1 SSC_BLOCKID: blk 1 SSC_POINTER: blk 1 SSC_CLOCK: blk 1 SSC_MODE: blk 1 SSC_DELAY: blk 1 SSC_WRITE_ResultCode: blk ; F8h supervisory key ; F8h result code ;F9h supervisory stack ptr key ; FAh block ID ; FBh pointer to data buffer ; FCh Clock ; FDh ClockW ClockE multiplier ; FEh flash macro sequence delay count 1 ; FFh temporary result code _main: mov A, 0 mov [SSC_BLOCKID], A// To read from Table 0 - Silicon ID is stored in Table 0 //Call SROM operation to read the SROM table mov X, SP ; copy SP into X mov A, X ; A temp stored in X add A, 3 ; create 3 byte stack frame (2 + pushed A) mov [SSC_KEY2], A ; save stack frame for supervisory code ; load the supervisory code for flash operations mov [SSC_KEY1], 3Ah ;FLASH_OPER_KEY - 3Ah mov 23 on page 18 SSC A,6 ; load A with specific operation. 06h is the code for Table read Table ; SSC call the supervisory ROM // At the end of the SSC command the silicon ID is stored in F8 (MSB) and F9(LSB) of the SRAM .terminate: jmp .terminate Document Number: 001-66502 Rev. *D Page 23 of 70 CYRF69303 Gain value for the register at location [0x38]: mov [57h], A mov A, reg[PITMRL] mov [58h],A mov [59h], A mov A, reg[PITMRL] mov [60h], A ;;;Start comparison mov A,[60h] mov X, [59h] sub A, [59h] jz done mov A, [59h] mov X, [58h] sub A, [58h] jz done mov X, [57h] ;;;correct data is in memory location 57h done: mov [57h], X ret 3.3 V = 0x40 3.0 V = 0x40 2.85 V = 0xFF 2.70 V = 0xFF Load register [0x38] with the gain values corresponding to the appropriate voltage. Table 34. Oscillator Trim Values vs. Voltage Settings Supervisory ROM Table Function Table2 FCh 24 MHz IOSCTR at 3.30 V Table2 FDh 24 MHz IOSCTR at 3.00 V Table2 FEh 24 MHz IOSCTR at 2.85 V Table2 FFh 24 MHz IOSCTR at 2.70 V Table3 F8h 32 kHz LPOSCTR at 3.30 V Table3 F9h 32 kHz LPOSCTR at 3.00 V Table3 FAh 32 kHz LPOSCTR at 2.85 V Table3 FBh 32 kHz LPOSCTR at 2.70 V Clock Architecture Description The CYRF69303 clock selection circuitry allows the selection of independent clocks for the CPU, Interval Timers, and Capture Timers. When using the 32 kHz oscillator the PITMRL/H must be read until two consecutive readings match before sending/receiving data. The following firmware example assumes the developer is interested in the lower byte of the PIT. Read_PIT_counter: mov A, reg[PITMRL] CPU Clock The CPU clock, CPUCLK, can be sourced from the Internal 24 MHz oscillator. The selected clock source can optionally be divided by 2n-1 where n is 0–7 (see Table 36 on page 25). Table 35. CPU Clock Config (CPUCLKCR) [0x30] [R/W] Bit # 7 6 5 4 Field 3 2 1 0 Reserved Read/Write – – – – – – – – Default 0 0 0 0 0 0 0 0 Bits 7:0 Reserved Note The CPU speed selection is configured using the OSC_CR0 Register (Figure 8 on page 27). Document Number: 001-66502 Rev. *D Page 24 of 70 CYRF69303 Table 36. OSC Control 0 (OSC_CR0) [0x1E0] [R/W] Bit # 7 Field 6 Reserved 5 No Buzz 4 3 2 Sleep Timer [1:0] 1 0 CPU Speed [2:0] Read/Write – – R/W R/W R/W R/W R/W R/W Default 0 0 0 0 1 0 0 0 Bits 7:6 Reserved Bit 5 No Buzz During sleep (the Sleep bit is set in the CPU_SCR Register — Table 40 on page 29), the POR detection circuit is turned on periodically to detect any POR events on the VCC pin (the Sleep Duty Cycle bits in the ECO_TR are used to control the duty cycle — Table 44 on page 33). To facilitate the detection of POR events, the No Buzz bit is used to force the POR detection circuit to be continuously enabled during sleep. This results in a faster response to a POR event during sleep at the expense of a slightly higher than average sleep current. Obtaining the absolute lowest power usage in sleep mode requires the No Buzz bit be clear 0 = The POR detection circuit is turned on periodically as configured in the Sleep Duty Cycle. 1 = The Sleep Duty Cycle value is overridden. The POR detection circuit is always enabled. Note The periodic Sleep Duty Cycle enabling is independent with the sleep interval shown in the following Sleep [1:0] bits. Bits 4:3 Sleep Timer [1:0] Sleep Timer Sleep Timer Clock [1:0] Frequency (Nominal) Sleep Period (Nominal) Watchdog Period (Nominal) 00 512 Hz 1.95 ms 6 ms 01 64 Hz 15.6 ms 47 ms 10 8 Hz 125 ms 375 ms 11 1 Hz 1 sec 3 sec Note Sleep intervals are approximate Bits 2:0 CPU Speed [2:0] The CYRF69303 may operate over a range of CPU clock speeds. The reset value for the CPU Speed bits is zero. Therefore, the default CPU speed is 3 MHz. CPU Speed CPU when Internal [2:0] Oscillator is selected 000 3 MHz (Default) 001 6 MHz 010 12 MHz 011 Reserved 100 1.5 MHz 101 750 kHz 110 187 kHz 111 Reserved Document Number: 001-66502 Rev. *D Page 25 of 70 CYRF69303 Table 37. Timer Clock Config (TMRCLKCR) [0x31] [R/W] Bit # 7 6 5 4 2 ITMRCLK Divider 1 0 Field TCAPCLK Divider Read/Write R/W R/W R/W R/W R/W R/W R/W R/W 1 0 0 0 1 1 1 1 Default TCAPCLK Select 3 ITMRCLK Select Bits 7:6TCAPCLK Divider [1:0] TCAPCLK Divider controls the TCAPCLK divisor. 0 0 = Divider Value 2 0 1 = Divider Value 4 1 0 = Divider Value 6 1 1 = Divider Value 8 Bits 5:4 TCAPCLK Select The TCAPCLK Select field controls the source of the TCAPCLK. 0 0 = Internal 24 MHz Oscillator 0 1 = Reserved 1 0 = Internal 32 kHz Low power Oscillator 1 1 = TCAPCLK Disabled Note The 1024 s interval timer is based on the assumption that TCAPCLK is running at 4 MHz. Changes in TCAPCLK frequency cause a corresponding change in the 1024 s interval timer frequency. Bits 3:2 ITMRCLK Divider ITMRCLK Divider controls the ITMRCLK divisor 0 0 = Divider value of 1 0 1 = Divider value of 2 1 0 = Divider value of 3 1 1 = Divider value of 4 Bits 1:0 ITMRCLK Select 0 0 = Internal 24 MHz Oscillator 0 1 = Reserved 1 0 = Internal 32 kHz Low power Oscillator 1 1 = TCAPCLK Note Changing the source of TMRCLK requires that both the source and destination clocks be running. Attempting to change the clock source away from TCAPCLK after that clock has been stopped is not successful. Interval Timer Clock (ITMRCLK) The Interval Timer clock (ITMRCLK) can be sourced from the internal 24 MHz oscillator, internal 32 kHz low power oscillator, or timer capture clock. A programmable prescaler of 1, 2, 3, or 4 then divides the selected source. The 12-bit Programmable Interval Timer is a simple down counter with a programmable reload value. It provides a 1 s resolution by default. When the down counter reaches zero, the next clock is spent reloading. The reload value can be read and written while the counter is running, but care must be taken to ensure that the counter does not unintentionally reload while the 12-bit reload value is only partially stored—for example, between the two writes of the 12-bit value. The programmable interval timer generates interrupt to the CPU on each reload. The parameters to be set appears on the device editor view of PSoC Designer after you place the CYRF69303 timer user module. The parameters are PITIMER_Source and PITIMER_Divider. The PITIMER_Source is the clock to the timer and the PITIMER_Divider is the value the clock is divided by. Document Number: 001-66502 Rev. *D The interval register (PITMR) holds the value that is loaded into the PIT counter on terminal count. The PIT counter is a down counter. The Programmable Interval Timer resolution is configurable. For example: TCAPCLK divide by x of CPU clock (for example TCAPCLK divide by 2 of a 24 MHz CPU clock gives a frequency of 12 MHz) ITMRCLK divide by x of TCAPCLK (for example, ITMRCLK divide by 3 of TCAPCLK is 4 MHz so resolution is 0.25 s). Timer Capture Clock (TCAPCLK) The Timer Capture clock (TCAPCLK) can be sourced from the internal 24 MHz oscillator or the internal 32 kHz low power oscillator. A programmable prescaler of 2, 4, 6, or 8 then divides the selected source. Page 26 of 70 CYRF69303 Figure 8. Programmable Interval Timer Block Diagram Configuration Status and Control System Clock 12-bit reload value 12-bit reload counter 12-bit down counter Clock Timer Interrupt Controller Internal Clock Trim Table 38. IOSC Trim (IOSCTR) [0x34] [R/W] Bit # 7 Field Read/Write Default 6 5 4 3 foffset[2:0] 2 1 0 Gain[4:0] R/W R/W R/W R/W R/W R/W R/W R/W 0 0 0 D D D D D The IOSC Calibrate register is used to calibrate the internal oscillator. The reset value is undefined but during boot the SROM writes a calibration value that is determined during manufacturing test. The ‘D’ indicates that the default value is trimmed to 24 MHz at 3.30 V at power on. Bits 7:5 foffset [2:0] This value is used to trim the frequency of the internal oscillator. These bits are not used in factory calibration and are zero. Setting each of these bits causes the appropriate fine offset in oscillator frequency: foffset bit 0 = 7.5 kHz foffset bit 1 = 15 kHz foffset bit 2 = 30 kHz Bits 4:0 Gain [4:0] The effective frequency change of the offset input is controlled through the gain input. A lower value of the gain setting increases the gain of the offset input. This value sets the size of each offset step for the internal oscillator. Nominal gain change (kHz/offsetStep) at each bit, typical conditions (24 MHz operation): Gain bit 0 = –1.5 kHz Gain bit 1 = –3.0 kHz Gain bit 2 = –6 kHz Gain bit 4 = –24 kHz Document Number: 001-66502 Rev. *D Page 27 of 70 CYRF69303 LPOSC Trim Table 39. LPOSC Trim (LPOSCTR) [0x36] [R/W] Bit # 7 6 32 kHz Low Power Reserved Field R/W – R/W R/W R/W R/W R/W R/W 0 – D D D D D D Read/Write Default 5 4 3 32 kHz Bias Trim [1:0] 2 1 0 32 kHz Freq Trim [3:0] This register is used to calibrate the 32 kHz Low speed Oscillator. The reset value is undefined but during boot the SROM writes a calibration value that is determined during manufacturing test. This is the meaning of ‘D’ in the Default field. The trim value can be adjusted vs. voltage as noted in Table 35 on page 24. Bit 7 32 kHz Low Power 0 = The 32 kHz Low speed Oscillator operates in normal mode. 1 = The 32 kHz Low speed Oscillator operates in a low power mode. The oscillator continues to function normally but with reduced accuracy. Bit 6 Reserved Bits [5:4] 32 kHz Bias Trim [1:0] These bits control the bias current of the low power oscillator. 0 0 = Mid bias 0 1 = High bias 1 0 = Reserved 1 1 = Reserved Important Note Do not program the 32 kHz Bias Trim [1:0] field with the reserved 10b value as the oscillator does not oscillate at all corner conditions with this setting. Bits 3:0 32 kHz Freq Trim [3:0] These bits are used to trim the frequency of the low power oscillator. CPU Clock During Sleep Mode When the CPU enters sleep mode, the oscillator is stopped. When the CPU comes out of sleep mode it is running on the internal oscillator. The internal oscillator recovery time is three clock cycles of the Internal 32 kHz Low power Oscillator. Document Number: 001-66502 Rev. *D Page 28 of 70 CYRF69303 Reset The microcontroller supports two types of resets: power-on reset (POR) and watchdog reset (WDR). When reset is initiated, all registers are restored to their default states and all interrupts are disabled. The occurrence of a reset is recorded in the System Status and Control Register (CPU_SCR). Bits within this register record the occurrence of POR and WDR Reset respectively. The firmware can interrogate these bits to determine the cause of a reset. The microcontroller resumes execution from Flash address 0x0000 after a reset. The internal clocking mode is active after a reset, until changed by user firmware. Note The CPU clock defaults to 3 MHz (Internal 24 MHz Oscillator divide-by-8 mode) at POR to guarantee operation at the low VCC that might be present during the supply ramp. Table 40. System Status and Control Register (CPU_SCR) [0xFF] [R/W] Bit # 7 6 5 4 3 2 1 0 Field GIES Reserved WDRS PORS Sleep Reserved Reserved Stop Read/Write R – R/C[3] R/C[3] R/W – – R/W Default 0 0 0 1 0 1 0 0 The bits of the CPU_SCR register are used to convey status and control of events for various functions of a CYRF69303 device. Bit 7 GIES The Global Interrupt Enable Status bit is a read-only status bit and its use is discouraged. The GIES bit is a legacy bit, which was used to provide the ability to read the GIE bit of the CPU_F register. However, the CPU_F register is now readable. When this bit is set, it indicates that the GIE bit in the CPU_F register is also set which, in turn, indicates that the microprocessor services interrupts: 0 = Global interrupts disabled 1 = Global interrupt enabled Bit 6 Reserved Bit 5 WDRS The WDRS bit is set by the CPU to indicate that a WDR event has occurred. The user can read this bit to determine the type of reset that has occurred. The user can clear but not set this bit: 0 = No WDR 1 = A WDR event has occurred Bit 4 PORS The PORS bit is set by the CPU to indicate that a POR event has occurred. The user can read this bit to determine the type of reset that has occurred. The user can clear but not set this bit: 0 = No POR 1 = A POR event has occurred (Note that WDR events do not occur until this bit is cleared). Bit 3 SLEEP Set by the user to enable CPU sleep state. CPU remains in sleep mode until any interrupt is pending. The Sleep bit is covered in more detail in the section Sleep Mode on page 30. 0 = Normal operation 1 = Sleep Bits 2:1 Reserved Bit 0 STOP This bit is set by the user to halt the CPU. The CPU remains halted until a reset (WDR, POR, or external reset) has taken place. If an application wants to stop code execution until a reset, the preferred method is to use the HALT instruction rather than writing to this bit. 0 = Normal CPU operation 1 = CPU is halted (not recommended) Note 3. C = Clear. This bit can only be cleared by the user and cannot be set by firmware. Document Number: 001-66502 Rev. *D Page 29 of 70 CYRF69303 Power-on Reset WDT cannot be disabled. The only exception to this is if a POR event takes place, which disables the WDT. POR occurs every time the power to the device is switched on. POR is released when the supply is typically 2.6 V for the upward supply transition, with typically 50 mV of hysteresis during the power on transient. Bit 4 of the System Status and Control Register (CPU_SCR) is set to record this event (the register contents are set to 00010000 by the POR). After a POR, the microprocessor is held off for approximately 20 ms for the VCC supply to stabilize before executing the first instruction at address 0x00 in the Flash. If the VCC voltage drops below the POR downward supply trip point, POR is reasserted. The VCC supply needs to ramp linearly from 0 to VCC in 0 to 200 ms. The sleep timer is used to generate the sleep time period and the Watchdog time period. The sleep timer uses the Internal 32 kHz Low power Oscillator system clock to produce the sleep time period. The user can program the sleep time period using the Sleep Timer bits of the OSC_CR0 Register (Table 36 on page 25). When the sleep time elapses (sleep timer overflows), an interrupt to the Sleep Timer Interrupt Vector is generated. The Watchdog Timer period is automatically set to be three counts of the Sleep Timer overflows. This represents between two and three sleep intervals depending on the count in the Sleep Timer at the previous WDT clear. When this timer reaches three, a WDR is generated. Important The PORS status bit is set at POR and can only be cleared by the user, and cannot be set by firmware. The user can either clear the WDT, or the WDT and the Sleep Timer. Whenever the user writes to the Reset WDT Register (RES_WDT), the WDT is cleared. If the data that is written is the hex value 0x38, the Sleep Timer is also cleared at the same time. Watchdog Timer Reset The user has the option to enable the WDT. The WDT is enabled by clearing the PORS bit. When the PORS bit is cleared, the Table 41. Reset Watchdog Timer (RESWDT) [0xE3] [W] Bit # 7 6 5 Field 4 3 2 1 0 Reset Watchdog Timer [7:0] Read/Write W W W W W W W W Default 0 0 0 0 0 0 0 0 Any write to this register clears the Watchdog Timer, a write of 0x38 also clears the Sleep Timer. Bits 7:0Reset Watchdog Timer [7:0] Sleep Mode The CPU can only be put to sleep by the firmware. This is accomplished by setting the Sleep bit in the System Status and Control Register (CPU_SCR). This stops the CPU from executing instructions, and the CPU remains asleep until an interrupt comes pending, or there is a reset event (either a Power on Reset, or a Watchdog Timer Reset). The Internal 32 kHz low speed oscillator remains running. Before entering suspend mode, firmware can optionally configure the 32 kHz Low speed Oscillator to operate in a low power mode to help reduce the overall power consumption (using the 32 kHz Low Power bit, Table 39). This helps save approximately 5 A; however, the trade off is that the 32 kHz Low speed Oscillator be less accurate (–53.12% to +56.25% deviation). All interrupts remain active. Only the occurrence of an interrupt wakes the part from sleep. The Stop bit in the System Status and Control Register (CPU_SCR) must be cleared for a part to resume out of sleep. The Global Interrupt Enable bit of the CPU Flags Register (CPU_F) does not have any effect. Any unmasked interrupt wakes the system up. As a result, any interrupts not intended for waking must be disabled through the Interrupt Mask Registers. Document Number: 001-66502 Rev. *D When the CPU enters sleep mode, the internal oscillator is stopped. When the CPU comes out of sleep mode, it is running on the internal oscillator. The internal oscillator recovery time is three clock cycles of the Internal 32 kHz Low power Oscillator. On exiting sleep mode, when the clock is stable and the delay time has expired, the instruction immediately following the sleep instruction is executed before the interrupt service routine (if enabled). The Sleep interrupt allows the microcontroller to wake up periodically and poll system components while maintaining very low average power consumption. The Sleep interrupt may also be used to provide periodic interrupts during non sleep modes. Sleep Sequence The Sleep bit is an input into the sleep logic circuit. This circuit is designed to sequence the device into and out of the hardware sleep state. The hardware sequence to put the device to sleep is shown in Figure 9 on page 31 and is defined as follows. 1. Firmware sets the SLEEP bit in the CPU_SCR0 register. The Bus Request (BRQ) signal to the CPU is immediately asserted. This is a request by the system to halt CPU operation at an instruction boundary. The CPU samples BRQ on the positive edge of CPUCLK. 2. Due to the specific timing of the register write, the CPU issues a Bus Request Acknowledge (BRA) on the following positive edge of the CPU clock. The sleep logic waits for the following negative edge of the CPU clock and then asserts a system-wide Power-down (PD) signal. In Figure 9 on page 31 the CPU is halted and the system-wide power-down signal is asserted. Page 30 of 70 CYRF69303 3. The system-wide PD (power-down) signal controls several major circuit blocks: The Flash memory module, the internal 24 MHz oscillator, the EFTB filter and the bandgap voltage reference. These circuits transition into a zero power state. The only operational circuits on chip are the Low Power oscillator, the bandgap refresh circuit, and the supply voltage monitor (POR) circuit. Low Power in Sleep Mode To achieve the lowest possible power consumption during suspend or sleep, the following conditions are observed in addition to considerations for the sleep timer: ■ All GPIOs are set to outputs and driven low ■ Clear P11CR[0], P10CR[0] ■ Set P10CR[1] ■ To avoid current consumption make sure ITMRCLK and TCPCLK are not sourced by either low power 32 kHz oscillator or 24 MHz crystal-less oscillator. All the other blocks go to the power-down mode automatically on suspend. The following steps are user configurable and help in reducing the average suspend mode power consumption: 1. Configure the power supply monitor at a large regular intervals, control register bits are 1,EB[7:6] (Power system sleep duty cycle PSSDC[1:0]). 2. Configure the Low power oscillator into low power mode, control register bit is LOPSCTR[7]. Figure 9. Sleep Timing Firmware write to SCR SLEEP bit causes an immediate BRQ CPU captures BRQ on next CPUCLK edge CPU responds with a BRA On the falling edge of CPUCLK, PD is asserted. The 24/48 MHz system clock is halted; the Flash and bandgap are powered down CPUCLK IOW SLEEP BRQ BRA PD Wakeup Sequence When asleep, the only event that can wake the system up is an interrupt. The global interrupt enable of the CPU flag register does not need to be set. Any unmasked interrupt wakes the system up. It is optional for the CPU to actually take the interrupt after the wakeup sequence. The wakeup sequence is synchronized to the 32 kHz clock. This is done to sequence a startup delay and enable the Flash memory module enough time to power-up before the CPU asserts the first read access. Another reason for the delay is to enable the oscillator, Bandgap, and POR circuits time to settle before actually being used in the system. As shown in Figure 10 on page 32, the wakeup sequence is as follows: Document Number: 001-66502 Rev. *D 1. The wakeup interrupt occurs and is synchronized by the negative edge of the 32 kHz clock. 2. At the following positive edge of the 32 kHz clock, the system-wide PD signal is negated. The Flash memory module, internal oscillator, EFTB, and bandgap circuit are all powered up to a normal operating state. 3. At the following positive edge of the 32 kHz clock, the current values for the precision POR have settled and are sampled. 4. At the following negative edge of the 32 kHz clock (after about 15 µs nominal), the BRQ signal is negated by the sleep logic circuit. On the following CPUCLK, BRA is negated by the CPU and instruction execution resumes. Note that in Figure 10 on page 32 fixed function blocks, such as Flash, internal oscillator, EFTB, and bandgap, have about 15 µs start up. The wakeup times (interrupt to CPU operational) ranges from 75 µs to 105 µs. Page 31 of 70 CYRF69303 Figure 10. Wakeup Timing Sleep Timer or GPIO interrupt occurs Interrupt is double sampled by 32K clock and PD is negated to system CPU is restarted after 90 ms (nominal) CLK32K INT SLEEP PD BANDGAP PPOR ENABLE SAMPLE SAMPLE POR CPUCLK/ 24MHz (Not to Scale) BRQ BRA CPU Power-on Reset Control Table 42. Power-on Reset Control Register (POR CR) [0x1E3] [R/W] Bit # 7 Field 6 5 Reserved 4 3 2 PORLEV[1:0] 1 0 Reserved Read/Write – – R/W R/W – – – – Default 0 0 0 0 0 0 0 0 This register controls the configuration of the Power on Reset circuit. This register can only be accessed in the second bank of I/O space. This requires setting the XIO bit in the CPU flags register. Bits 7:6 Reserved Bits 5:4 PORLEV[1:0] This field controls the level below which the precision power on reset (PPOR) detector generates a reset 0 0 = 2.7 V Range (trip near 2.6 V) 0 1 = 3 V Range (trip near 2.9 V) 1 0 = Reserved 1 1 = PPOR does not generate a reset, but values read from the Voltage Monitor Comparators Register (Table 43 on page 33) give the internal PPOR comparator state with trip point set to the 3 V range setting. Bits 3:0 Reserved Document Number: 001-66502 Rev. *D Page 32 of 70 CYRF69303 POR Compare State Table 43. Voltage Monitor Comparators Register (VLTCMP) [0x1E4] [R] Bit # 7 6 5 Field 4 3 2 1 Reserved 0 PPOR Read/Write – – – – – – – R Default 0 0 0 0 0 0 0 0 This read-only register allows reading the current state of the Precision-Power-On-Reset comparators: Bits 7:1 Reserved Bit 0 PPOR This bit is set to indicate that the precision-power-on-reset comparator has tripped, indicating that the supply voltage is below the trip point set by PORLEV[1:0]: 0 = No precision-power-on-reset event 1 = A precision-power-on-reset event has tripped Note This register can only be accessed in the second bank of I/O space. This requires setting the XIO bit in the CPU flags register ECO Trim Register Table 44. ECO (ECO_TR) [0x1EB] [R/W] Bit # Field Read/Write Default 7 6 5 4 3 Sleep Duty Cycle [1:0] 2 1 0 Reserved R/W R/W – – – – – – 0 0 0 0 0 0 0 0 This register controls the ratios (in numbers of 32 kHz clock periods) of ‘on’ time versus ‘off’ time for POR detection circuit. Bits 7:6 Sleep Duty Cycle [1:0] 0 0 = 1/128 periods of the Internal 32 kHz low-speed Oscillator 0 1 = 1/512 periods of the Internal 32 kHz low-speed Oscillator 1 0 = 1/32 periods of the Internal 32 kHz low-speed Oscillator 1 1 = 1/8 periods of the Internal 32 kHz low speed Oscillator Note This register can only be accessed in the second bank of I/O space. This requires setting the XIO bit in the CPU flags register General-Purpose I/O Ports The general-purpose I/O ports are discussed in the following sections. Port Data Registers Table 45. P0 Data Register (P0DATA)[0x00] [R/W] Bit # 7 Field P0.7 Read/Write R/W Default 0 6 5 4 3 2 1 0 Reserved P0.4/INT2 P0.3/INT1 Reserved P0.1 Reserved – R/W R/W – R/W – 0 0 0 0 – – – This register contains the data for Port 0. Writing to this register sets the bit values to be output on output enabled pins. Reading from this register returns the current state of the Port 0 pins. Bit 7 P0.7 Data Bits 6:5 Reserved Bits 4:3 P0.4–P0.3Data/INT2–INT1 In addition to their use as the P0.4–P0.3 GPIOs, these pins can also be used for the alternative functions as the Interrupt pins (INT1–INT2). To configure the P0.4–P0.3 pins, refer to the P0.3/INT1–P0.4/INT2 Configuration Register (Table 49 on page 37). Bit 2 Reserved Bit 1 P0.1 Data Bit 0 Reserved Document Number: 001-66502 Rev. *D Page 33 of 70 CYRF69303 Table 46. P1 Data Register (P1DATA) [0x01] [R/W] Bit # 7 6 5 4 3 2 1 0 Field P1.7 P1.6 P1.5/SMOSI P1.4/SCLK P1.3/SSEL P1.2 P1.1 P1.0 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W 0 0 0 0 0 0 0 – Default This register contains the data for Port 1. Writing to this register sets the bit values to be output on output enabled pins. Reading from this register returns the current state of the Port 1 pins. Bits 7 P1.7 Bits 6 P1.6 or alternate function of SMOSI in a 4-wire SPI Bits 5:3 P1.5–P1.3 Data/3-wire SPI Pins (SMISO/SMOSI, SCLK, SSEL) In addition to their use as the P1.6–P1.3 GPIOs, these pins can also be used for the alternative function as the SPI interface pins. To configure the P1.6–P1.3 pins, refer to the P1.3–P1.6 Configuration Register (Table 49 on page 37) Bits 2:1 P1.2–P1.1 Bit 0 P1.0 Table 47. P2 Data Register (P2DATA) [0x02] [R/W] Bit # 7 6 Field 5 4 3 2 1 Reserved 0 P2.1–P2.0 Read/Write - R/W R/W Default - 0 0 This register contains the data for Port 2. Writing to this register sets the bit values to be output on output enabled pins. Reading from this register returns the current state of the Port 2 pins. Bits 7:2 P2 Data [7:2] Bits 1:0 P2 Data [1:0] Document Number: 001-66502 Rev. *D Page 34 of 70 CYRF69303 GPIO Port Configuration On the CY7C601xx, only the P3.7, P2.7, P0.1, and P0.0 have 50 mA sink drive capability. Other pins have 8 mA sink drive capability. All the GPIO configuration registers have common configuration controls. The following are the bit definitions of the GPIO configuration registers. By default all GPIOs are configured as inputs. To prevent the inputs from floating, the pull-up resistors are enabled. Firmware needs to configure each of the GPIOs before use. On the CY7C602xx, only the P1.7–P1.3 have 50 mA sink drive capability. Other pins have 8 mA sink drive capability. Open Drain When set, the output on the pin is determined by the Port Data Register. If the corresponding bit in the Port Data Register is set, the pin is in high impedance state. If the corresponding bit in the Port Data Register is clear, the pin is driven LOW. Int Enable When set, the Int Enable bit allows the GPIO to generate interrupts. Interrupt generate can occur regardless of whether the pin is configured for input or output. All interrupts are edge sensitive, however for any interrupt that is shared by multiple sources (that is, Ports 2, 3, and 4) all inputs must be deasserted before a new interrupt can occur. When clear, the output is driven LOW or HIGH. Pull-up Enable When set the pin has a 7K pull-up to VDD. When clear, the corresponding interrupt is disabled on the pin. When clear, the pull-up is disabled. It is possible to configure GPIOs as outputs, enable the interrupt on the pin and then to generate the interrupt by driving the appropriate pin state. This is useful in test and may have value in applications. Output Enable When set, the output driver of the pin is enabled. When clear, the output driver of the pin is disabled. Int Act Low For pins with shared functions there are some special cases. When clear, the corresponding interrupt is active HIGH. When set, the interrupt is active LOW. For P0.3–P0.4 Int act Low clear causes interrupts to be active on the rising edge. Int act Low set causes interrupts to be active on the falling edge. P0.0 (CLKIN) and P0.1 (CLKOUT) can not be output enabled when the crystal oscillator is enabled. Output enables for these pins are overridden by XOSC Enable. P1.3 (SSEL), P1.4 (SCLK), P1.5 (SMOSI) and P1.6 (SMISO) can be used for their dedicated functions or for GPIO. To enable the pin for GPIO use, clear the corresponding SPI Use bit or the Output Enable has no effect. TTL Thresh When set, the input has TTL threshold. When clear, the input has standard CMOS threshold. SPI Use Important Note The GPIOs default to CMOS threshold. User’s firmware needs to configure the threshold to TTL mode if necessary. The P1.3 (SSEL), P1.4 (SCLK), P1.5 (SMOSI) and P1.6 (SMISO) pins can be used for their dedicated functions or for GPIO. To enable the pin for GPIO, clear the corresponding SPI Use bit. The SPI function controls the output enable for its dedicated function pins when their GPIO enable bit is clear. High Sink When set, the output can sink up to 50 mA. When clear, the output can sink up to 8 mA. Table 48. P0.1 Configuration (P01CR) [0x06] R/W] Bit # 7 6 5 4 3 2 1 0 Reserved Int Enable Int Act Low TTL Thresh High Sink Open Drain Pull-up Enable Output Enable R/W R/W R/W R/W R/W R/W R/W R/W 0 0 0 0 0 0 0 0 Field Read/Write Default Document Number: 001-66502 Rev. *D Page 35 of 70 CYRF69303 Table 48. P0.1 Configuration (P01CR) [0x06] R/W] This register is used to configure P0.1. In the CYRF69303, only 8 mA sink drive capability is available on this pin regardless of the setting of the High Sink bit. If this pin is used as a general purpose output it draws current. This pin must be configured as an input to reduce current draw. Bit 7 Reserved Bit 6 see Section Int Enable Bit 5 see Section Int Act LowInt Act Low Bit 4 see Section TTL Thresh Bit 3 see Section High Sink Bit 2 see Section Open DrainOpen Drain Bit 1 see Section Pull-up Enable Bit 0 see Section Output Enable Document Number: 001-66502 Rev. *D Page 36 of 70 CYRF69303 Table 49. P0.3–P0.4 Configuration (P03CR–P04CR) [0x08–0x09] [R/W] Bit # 7 6 Reserved 5 4 3 2 1 0 Int Act Low TTL Thresh Reserved Open Drain Pull-up Enable Output Enable Field Read/Write – – R/W R/W – R/W R/W R/W Default 0 0 0 0 0 0 0 0 These registers control the operation of pins P0.3–P0.4 respectively. These pins are shared between the P0.3–P0.4 GPIOs and the INT1–INT2. The INT1–INT2 interrupts are different than all the other GPIO interrupts. These pins are connected directly to the interrupt controller to provide three edge-sensitive interrupts with independent interrupt vectors. These interrupts occur on a rising edge when Int act Low is clear and on a falling edge when Int act Low is set. These pins are enabled as interrupt sources in the interrupt controller registers (Table 75 on page 52 and Table 73 on page 51). To use these pins as interrupt inputs, configure them as inputs by clearing the corresponding Output Enable. If the INT1–INT2 pins are configured as outputs with interrupts enabled, firmware can generate an interrupt by writing the appropriate value to the P0.3, and P0.4 data bits in the P0 Data Register. Regardless of whether the pins are used as Interrupt or GPIO pins the Int Enable, Int act Low, TTL Threshold, Open Drain, and Pull-up Enable bits control the behavior of the pin. The P0.3/INT1–P0.4/INT2 pins are individually configured with the P03CR (0x08), and P04CR (0x09) respectively. Note Changing the state of the Int Act Low bit can cause an unintentional interrupt to be generated. When configuring these interrupt sources, it is best to follow the following procedure: 1. Disable interrupt source 2. Configure interrupt source 3. Clear any pending interrupts from the source 4. Enable interrupt source Table 50. P0.7 Configuration (P07CR) [0x0C] [R/W] Bit # 7 6 5 4 3 2 1 0 Reserved Int Enable Int Act Low TTL Thresh Reserved Open Drain Pull-up Enable Output Enable – R/W R/W R/W – R/W R/W R/W 0 0 0 0 0 0 Field Read/Write Default 0 0 This register controls the operation of pin P0.7. Bit 7 Reserved Bit 6 see Section Int Enable Bit 5 see Section Int Act Low Bit 4 see Section TTL ThreshHigh Sink Bit 3 Reserved Bit 2 see Section Open Drain Bit 1 see Section Pull-up Enable Bit 0 see Section Output Enable Document Number: 001-66502 Rev. *D Page 37 of 70 CYRF69303 Table 51. P1.0 Configuration (P10CR) [0x0D] [R/W] Bit # 7 6 5 4 3 2 1 0 Reserved Int Enable Int Act Low Reserved Reserved Reserved 5K pullup Enable Output enable R/W R/W R/W – – – R/W R/W 0 0 0 0 0 0 0 0 Field Read/Write Default This register controls the operation of the P1.0 pin. Note The P1.0 is an open drain only output. It can actively drive a signal low, but cannot actively drive a signal high. Bit 0 This bit enables the output on P1.0. This bit must be cleared in sleep mode. Bit 7 Reserved Bit 6 see Section Int Enable Bit 5 see Section Int Act Low Bit 4 Reserved Bit 3 Reserved Bit 2 Reserved Bit 1 0 = disables the 5K ohm pull-up resistors 1 = enables 5K ohm pull-up resistors for both P1.0 and P1.1 (this is not compatible with USB) Table 52. P1.1 Configuration (P11CR) [0x0E] [R/W] Bit # 7 6 5 Reserved Int Enable Int Act Low 4 Read/Write – R/W R/W – Default 0 0 0 0 3 2 1 0 Open Drain Reserved Output Enable – R/W – R/W 0 0 0 0 Reserved Field This register controls the operation of the P1.1 pin. The pull-up resistor on this pin is enabled by the P10CR Register. Note There is no 2 mA sourcing capability on this pin. The pin can only sink 5 mA at VOL3 section. Bit 7 Reserved Bit 6 see Section Int Enable Bit 5 see Section Int Act Low Bit 4 Reserved Bit 3 Reserved Bit 2 see Section Open Drain Bit 1 Reserved Bit 0 see Section Output Enable Document Number: 001-66502 Rev. *D Page 38 of 70 CYRF69303 Table 53. P1.2 Configuration (P12CR) [0x0F] [R/W] Bit # 7 6 5 4 3 2 1 0 CLK Output Int Enable Int Act Low TTL Threshold Reserved Open Drain Pull-up Enable Output Enable R/W R/W R/W R/W – R/W R/W R/W 0 0 0 0 0 0 0 0 Field Read/Write Default This register controls the operation of the P1.2. Bit 7 CLK Output 0 = The internally selected clock is not sent out onto P1.2 pin. 1 = When CLK Output is set, the internally selected clock is sent out onto P1.2 pin. Bit 6 see Section Int Enable Bit 5 see Section Int Act Low Bit 4 Reserved Bit 3 see Section High Sink Bit 2 see Section Open Drain Bit 1 see Section Pull-up Enable Bit 0 see Section Output Enable Table 54. P1.3 Configuration (P13CR) [0x10] [R/W] Bit # 7 6 5 4 3 2 1 0 Reserved Int Enable Int Act Low Reserved High Sink Open Drain Pull-up Enable Output Enable Read/Write – R/W R/W – R/W R/W R/W R/W Default 0 0 0 0 0 0 0 0 Field This register controls the operation of the P1.3 pin. The P1.3 GPIO’s threshold is always set to TTL. When the SPI hardware is enabled, the output enable and output state of the pin is controlled by the SPI circuitry. When the SPI hardware is disabled, the pin is controlled by the Output Enable bit and the corresponding bit in the P1 data register. Regardless of whether the pin is used as an SPI or GPIO pin the Int Enable, Int act Low, High Sink, Open Drain, and Pull-up Enable control the behavior of the pin. 50 mA sink drive capability is available. Bit 7 Reserved Bit 6 see Section Int Enable Bit 5 see Section Int Act Low Bit 4 Reserved Bit 3 see Section High Sink Bit 2 see Section Open Drain Bit 1 see Section Pull-up Enable Bit 0 see Section Output Enable Document Number: 001-66502 Rev. *D Page 39 of 70 CYRF69303 Table 55. P1.4–P1.6 Configuration (P14CR–P16CR) [0x11–0x13] [R/W] Bit # 7 6 5 4 3 2 1 0 SPI Use Int Enable Int Act Low Reserved High Sink Open Drain Pull-up Enable Output Enable R/W R/W R/W – R/W R/W R/W R/W 0 0 0 0 0 0 0 0 Field Read/Write Default These registers control the operation of pins P1.4–P1.6, respectively. The P1.4–P1.6 GPIO’s threshold is always set to TTL. When the SPI hardware is enabled, pins that are configured as SPI Use have their output enable and output state controlled by the SPI circuitry. When the SPI hardware is disabled or a pin has its SPI Use bit clear, the pin is controlled by the Output Enable bit and the corresponding bit in the P1 data register. Regardless of whether any pin is used as an SPI or GPIO pin the Int Enable, Int act Low, High Sink, Open Drain, and Pull-up Enable control the behavior of the pin. The 50 mA sink drive capability is only available in the CY7C602xx. In the CY7C601xx, only 8 mA sink drive capability is available on this pin regardless of the setting of the High Sink bit. Bit 7 SPI Use 0 = Disable the SPI alternate function. The pin is used as a GPIO 1 = Enable the SPI function. The SPI circuitry controls the output of the pin Bit 6 see Section Int Enable Bit 5 see Section Int Act Low Bit 4 Reserved Bit 3 see Section High Sink Bit 2 see Section Open Drain Bit 1 see Section Pull-up Enable Bit 0 see Section Output Enable Note For Comm Modes 01 or 10 (SPI Master or SPI Slave, see Table 59 on page 43) When configured for SPI (SPI Use = 1 and Comm Modes [1:0] = SPI Master or SPI Slave mode), the input/output direction of pins P1.3, P1.5, and P1.6 is set automatically by the SPI logic. However, pin P1.4's input/output direction is NOT automatically set; it must be explicitly set by firmware. For SPI Master mode, pin P1.4 must be configured as an output; for SPI Slave mode, pin P1.4 must be configured as an input. Table 56. P1.7 Configuration (P17CR) [0x14] [R/W] Bit # 7 6 5 4 3 2 1 0 Reserved Int Enable Int Act Low Reserved High Sink Open Drain Pull-up Enable Output Enable Read/Write – R/W R/W – R/W R/W R/W R/W Default 0 0 0 0 0 0 0 0 Field This register controls the operation of pin P1.7. 50 mA sink drive capability is available. The P1.7 GPIO’s threshold is always set to TTL. Bit 7 Reserved Bit 6 see Section Int Enable Bit 5 see Section Int Act Low Bit 4 Reserved Bit 3 see Section High Sink Bit 2 see Section Open Drain Bit 1 see Section Pull-up Enable Bit 0 see Section Output Enable Document Number: 001-66502 Rev. *D Page 40 of 70 CYRF69303 Table 57. P2 Configuration (P2CR) [0x15] [R/W] Bit # 7 6 5 4 3 2 1 0 Reserved Int Enable Int Act Low TTL Thresh High Sink Open Drain Pull-up Enable Output Enable Read/Write – R/W R/W R/W R/W R/W R/W R/W Default 0 0 0 0 0 0 0 0 Field This register controls the operation of pins P2.0–P2.1. Bit 7 Reserved Bit 6 see Section Int Enable Bit 5 see Section Int Act LowTTL Thresh Bit 4 see Section TTL Thresh Bit 3 see Section High Sink Bit 2 see Section Open DrainPull-up Enable Bit 1 see Section Pull-up Enable Bit 0 see Section Output Enable GPIO Configurations for Low Power Mode To ensure low power mode, unbonded GPIO pins in CYRF69303 must be placed in a non-floating state. The following assembly code snippet shows how this is achieved. This snippet can be added as a part of the initialization routine. //Code Snippet for addressing unbonded GPIOs mov A, 01h mov reg[1Fh],A mov A, 01h mov reg[16h],A // Port3 Configuration register - Enable output mov A, 00h mov reg[03h],A // Asserting P3.0 to P3.7 outputs to '0' //Port 2 configurations mov A,01h mov reg[15h],A //Port 2 Configuration register -Enable output mov A,00h mov reg[02h],A //Asserting P2.0 to P2.7 outputs to ‘0’ mov A, 01h mov reg[05h],A // Port0.0 Configuration register - Enable output mov reg[07h],A // Port0.2 Configuration register - Enable output mov reg[0Ah],A // Port0.5 Configuration register - Enable output mov reg[0Bh],A // Port0.6 Configuration register - Enable output mov A,reg[00h] mov A,00h and A,9Ah mov reg[00h], A // Asserting outputs '0' to pins in port 1 // NOTE: The code fragment in italics is to be used only if your application configures P2.0 and P2.1 as push-pull outputs. When writing to port 0, to access GPIOs P0.1,3,4,7, mask bits 0,2,5,6. Failing to do so voids the low power. Document Number: 001-66502 Rev. *D Page 41 of 70 CYRF69303 Serial Peripheral Interface (SPI) The SPI Master/Slave Interface core logic runs on the SPI clock domain. The SPI clock is a divider off of the CPUCLK when in Master Mode. SPI is a four-pin serial interface comprised of a clock, an enable, and two data pins. Figure 11. SPI Block Diagram Register Block SCK Speed Sel SCK Clock Generation Master/Slave Sel SCK Clock Select SCK Polarity SCK_OE SCK Clock Phase/Polarity Select SCK Phase SCK SCK Little Endian Sel LE_SEL GPIO Block SS_N SS_N SPI State Machine SS_N_OE SS_N Data (8 bit) Load MISO_OE Output Shift Buffer Empty Master/Slave Set MISO/MOSI Crossbar MISO SCK LE_SEL Shift Buffer MOSI_OE MOSI Data (8 bit) Input Shift Buffer Load Full Sclk Output Enable Slave Select Output Enable Master IN, Slave Out OE Master Out, Slave In, OE Document Number: 001-66502 Rev. *D SCK_OE SS_N_OE MISO_OE MOSI_OE Page 42 of 70 CYRF69303 SPI Data Register Table 58. SPI Data Register (SPIDATA) [0x3C] [R/W] Bit # 7 6 5 4 Field Read/Write Default 3 2 1 0 SPIData[7:0] R/W R/W R/W R/W R/W R/W R/W R/W 0 0 0 0 0 0 0 0 When read, this register returns the contents of the receive buffer. When written, it loads the transmit holding register. Bits 7:0SPI Data [7:0] When an interrupt occurs to indicate to firmware that an byte of receive data is available, or the transmitter holding register is empty, firmware has 7 SPI clocks to manage the buffers — to empty the receiver buffer, or to refill the transmit holding register. Failure to meet this timing requirement results in incorrect data transfer. SPI Configure Register Table 59. SPI Configure Register (SPICR) [0x3D] [R/W] Bit # 7 6 Field Swap LSB First Read/Write R/W R/W R/W R/W 0 0 0 0 Default 5 4 Comm Mode 3 2 1 0 CPOL CPHA R/W R/W R/W R/W 0 0 0 0 SCLK Select Bit 7 Swap 0 = Swap function disabled. 1 = The SPI block swaps its use of SMOSI and SMISO. Among other things, this can be useful in implementing single wire SPI-like communications. Bit 6 LSB First 0 = The SPI transmits and receives the MSB (Most Significant Bit) first. 1 = The SPI transmits and receives the LSB (Least Significant Bit) first. Bits 5:4 Comm Mode [1:0] 0 0: All SPI communication disabled. 0 1: SPI master mode 1 0: SPI slave mode 1 1: Reserved Bit 3 CPOL This bit controls the SPI clock (SCLK) idle polarity. 0 = SCLK idles low 1 = SCLK idles high Bit 2 CPHA The Clock Phase bit controls the phase of the clock on which data is sampled. Table 60 on page 44 shows the timing for the various combinations of LSB First, CPOL, and CPHA. Bits 1:0 SCLK Select This field selects the speed of the master SCLK. When in master mode, SCLK is generated by dividing the base CPUCLK. Important Note for Comm Modes 01b or 10b (SPI Master or SPI Slave): When configured for SPI, (SPI Use = 1 — Table 55 on page 40), the input/output direction of pins P1.3, P1.5, and P1.6 is set automatically by the SPI logic. However, pin P1.4's input/output direction is NOT automatically set; it must be explicitly set by firmware. For SPI Master mode, pin P1.4 must be configured as an output; for SPI Slave mode, pin P1.4 must be configured as an input. Document Number: 001-66502 Rev. *D Page 43 of 70 CYRF69303 Table 60. SPI Mode Timing vs. LSB First, CPOL and CPHA LSB First CPHA CPOL 0 0 0 Diagram SCLK SSEL D AT A 0 0 X MSB B it 7 B it 6 B it 5 B it 4 B it 3 B it 2 LSB X X MSB B it 7 B it 6 B it 5 B it 4 B it 3 B it 2 LSB X 1 SC LK SSEL DAT A 0 1 0 SC LK SSEL DAT A 0 1 X MSB B it 7 B it 6 B it 5 B it 4 B it 3 B it 2 LS B X X MS B B it 7 B it 6 B it 5 B it 4 B it 3 B it 2 LS B X 1 SC L K SSEL D AT A 1 0 0 SCLK SSEL DAT A 1 0 X LSB B it 2 B it 3 B it 4 B it 5 B it 6 B it 7 MS B X X LSB Bit 2 Bit 3 Bit 4 Bit 5 Bit 6 Bit 7 MSB X 1 SCLK SSEL DAT A 1 1 0 SCLK SSEL DAT A 1 1 X LSB Bit 2 Bit 3 Bit 4 Bit 5 Bit 6 Bit 7 MSB X X LSB Bit 2 Bit 3 Bit 4 Bit 5 Bit 6 Bit 7 MSB X 1 SC LK SSEL DAT A Document Number: 001-66502 Rev. *D Page 44 of 70 CYRF69303 Timer Registers Table 61. SPI SCLK Frequency SCLK Select CPUCLK Divisor All timer functions of the CYRF69303 are provided by a single timer block. The timer block is asynchronous from the CPU clock. The 16-bit free running counter is used as the time-base for timer captures and can also be used as a general time-base by software. SCLK Frequency when CPUCLK = 12 MHz 00 6 2 MHz 01 12 1 MHz 10 48 250 kHz 11 96 125 kHz Registers Free Running Counter The 16-bit free running counter is clocked by a 4 or 6 MHz source. It can be read in software for use as a general purpose time base. When the low order byte is read, the high order byte is registered. Reading the high order byte reads this register allowing the CPU to read the 16-bit value atomically (loads all bits at one time). The free running timer generates an interrupt at 1024 s rate. It can also generate an interrupt when the free running counter overflow occurs — every 16.384 ms. This allows extending the length of the timer in software. SPI Interface Pins The SPI interface between the radio function and MCU function uses pins P1.3–P1.5 and optionally P1.6. These pins are configured using the P1.3 and P1.4–P1.6 Configuration. Figure 12. 16-bit Free Running Counter Block Diagram Overflow Interrupt Timer Capture Clock 16-bit Free Running Counter 1024-us Timer Interrupt Table 62. Free Running Timer Low Order Byte (FRTMRL) [0x20] [R/W] Bit # 7 6 5 Field Read/Write Default 4 3 2 1 0 Free Running Timer [7:0] R/W R/W R/W R/W R/W R/W R/W R/W 0 0 0 0 0 0 0 0 Bits 7:0 Free running Timer [7:0] This register holds the low order byte of the 16-bit free running timer. Reading this register causes the high order byte to be moved into a holding register allowing an automatic read of all 16 bits simultaneously. For reads, the actual read occurs in the cycle when the low order is read. For writes the actual time the write occurs is the cycle when the high order is written. When reading the free running timer, the low order byte must be read first and the high order second. When writing, the low order byte must be written first then the high order byte. Document Number: 001-66502 Rev. *D Page 45 of 70 CYRF69303 Table 63. Free Running Timer High-Order Byte (FRTMRH) [0x21] [R/W] Bit # 7 6 5 Field Read/Write Default 4 3 2 1 0 Free Running Timer [15:8] R/W R/W R/W R/W R/W R/W R/W R/W 0 0 0 0 0 0 0 0 Bits 7:0 Free Running Timer [15:8] When reading the free running timer, the low order byte must be read first and the high order second. When writing, the low order byte must be written first then the high order byte. Table 64. Programmable Interval Timer Low (PITMRL) [0x26] [R] Bit # 7 6 5 Read/Write R R R R Default 0 0 0 0 Field 4 3 2 1 0 R R R R 0 0 0 0 Prog Interval Timer [7:0] Bits 7:0 Prog Interval Timer [7:0] This register holds the low order byte of the 12-bit programmable interval timer. Reading this register causes the high order byte to be moved into a holding register allowing an automatic read of all 12 bits simultaneously. Table 65. Programmable Interval Timer High (PITMRH) [0x27] [R] Bit # 7 6 Field 5 4 3 Reserved 2 1 0 Prog Interval Timer [11:8] Read/Write -- -- -- -- R R R R Default 0 0 0 0 0 0 0 0 Bits 7:4 Reserved Bits 3:0 Prog Internal Timer [11:8] This register holds the high order nibble of the 12-bit programmable interval timer. Reading this register returns the high order nibble of the 12-bit timer at the instant that the low order byte was last read. Table 66. Programmable Interval Reload Low (PIRL) [0x28] [R/W] Bit # 7 6 5 4 R/W R/W R/W R/W 0 0 0 0 Field Read/Write Default 3 2 1 0 R/W R/W R/W R/W 0 0 0 0 Prog Interval [7:0] Bits 7:0 Prog Interval [7:0] This register holds the lower 8 bits of the timer. While writing into the 12-bit reload register, write lower byte first then the higher nibble. Document Number: 001-66502 Rev. *D Page 46 of 70 CYRF69303 Table 67. Programmable Interval Reload High (PIRH) [0x29] [R/W] Bit # 7 6 Field 5 4 3 Reserved 2 1 0 Prog Interval[11:8] Read/Write -- -- -- -- R/W R/W R/W R/W Default 0 0 0 0 0 0 0 0 Bits [7:4] Reserved Bits 3:0 Prog Interval [11:8] This register holds the higher 4 bits of the timer. While writing into the 12-bit reload register, write lower byte first then the higher nibble. Figure 13. 16-Bit Free Running Counter Loading Timing Diagram clk_sys write valid addr write data FRT reload ready Clk Timer 12b Prog Timer 12b reload interrupt 12-bit programmable timer load timing Capture timer clk 16b free running counter load 16b free running counter 00A0 00A1 00A2 00A3 00A4 00A5 00A6 00A7 00A8 00A9 00AB 00AC 00AD 00AE 00AF 00B0 00B1 00B2 ACBE ACBF ACC0 16-bit free running counter loading timing Document Number: 001-66502 Rev. *D Page 47 of 70 CYRF69303 Figure 14. Memory Mapped Registers Read/Write Timing Diagram clk_sys rd_wrn Valid Addr rdata wdata Memory mapped registers Read/Write timing diagram Interrupt Controller Table 68. Interrupt Priorities, Address, Name (continued) The interrupt controller and its associated registers allow the user’s code to respond to an interrupt from almost every functional block in the CYRF69303 devices. The registers associated with the interrupt controller allow interrupts to be disabled either globally or individually. The registers also provide a mechanism by which a user may clear all pending and posted interrupts, or clear individual posted or pending interrupts. Interrupt Priority Interrupt Address 17 0044h 16-bit Free Running Timer Wrap 18 0048h INT2 19 004Ch Reserved Name 20 0050h GPIO Port 2 The following table lists all interrupts and the priorities that are available in the CYRF69303. 21 0054h Reserved 22 0058h Reserved Table 68. Interrupt Priorities, Address, Name 23 005Ch Reserved 24 0060h Reserved 25 0064h Sleep Timer Interrupt Priority Interrupt Address 0 0000h Reset 1 0004h POR Architectural Description 2 0008h Reserved 3 000Ch SPI Transmitter Empty 4 0010h SPI Receiver Full An interrupt is posted when its interrupt conditions occur. This results in the flip-flop in Figure 15 on page 49 clocking in a ‘1’. The interrupt remains posted until the interrupt is taken or until it is cleared by writing to the appropriate INT_CLRx register. 5 0014h GPIO Port 0 6 0018h GPIO Port 1 7 001Ch INT1 8 0020h Reserved 9 0024h Reserved 10 0028h Reserved Name 11 002Ch Reserved 12 0030h Reserved 13 0034h 1 ms Interval timer 14 0038h Programmable Interval Timer 15 003Ch Reserved 16 0040h Reserved Document Number: 001-66502 Rev. *D A posted interrupt is not pending unless it is enabled by setting its interrupt mask bit (in the appropriate INT_MSKx register). All pending interrupts are processed by the Priority Encoder to determine the highest priority interrupt which is taken by the M8C if the Global Interrupt Enable bit is set in the CPU_F register. Disabling an interrupt by clearing its interrupt mask bit (in the INT_MSKx register) does not clear a posted interrupt, nor does it prevent an interrupt from being posted. It simply prevents a posted interrupt from becoming pending. Nested interrupts can be accomplished by reenabling interrupts inside an interrupt service routine. To do this, set the IE bit in the Flag Register. A block diagram of the CYRF69303 Interrupt Controller is shown in Figure 15. Page 48 of 70 CYRF69303 Figure 15. Interrupt Controller Block Diagram Priority Encoder Interrupt Taken or Interrupt Vector INT_CLRx Write Posted Interrupt Pending Interrupt D ... ... R 1 Interrupt Request Q Interrupt Source (Timer, GPIO, etc.) M8C Core CPU_F[0] GIE INT_MSKx Mask Bit Setting Interrupt Processing The sequence of events that occur during interrupt processing is as follows: 1. An interrupt becomes active, either because: a. The interrupt condition occurs (for example, a timer expires). b. A previously posted interrupt is enabled through an update of an interrupt mask register. c. An interrupt is pending and GIE is set from 0 to 1 in the CPU Flag register. 1. The current executing instruction finishes. 2. The internal interrupt is dispatched, taking 13 cycles. During this time, the following actions occur: a. The MSB and LSB of Program Counter and Flag registers (CPU_PC and CPU_F) are stored onto the program stack by an automatic CALL instruction (13 cycles) generated during the interrupt acknowledge process. b. The PCH, PCL, and Flag register (CPU_F) are stored onto the program stack (in that order) by an automatic CALL instruction (13 cycles) generated during the interrupt acknowledge process. c. The CPU_F register is then cleared. Because this clears the GIE bit to 0, additional interrupts are temporarily disabled. d. The PCH (PC[15:8]) is cleared to zero. e. The interrupt vector is read from the interrupt controller and its value placed into PCL (PC[7:0]). This sets the program counter to point to the appropriate address in the interrupt table (for example, 0004h for the POR interrupt). 1. Program execution vectors to the interrupt table. Typically, a LJMP instruction in the interrupt table sends execution to the user's Interrupt Service Routine (ISR) for this interrupt. 2. The ISR executes. Note that interrupts are disabled because GIE = 0. In the ISR, interrupts can be re-enabled if desired by setting GIE = 1 (care must be taken to avoid stack overflow). Document Number: 001-66502 Rev. *D 3. The ISR ends with a RETI instruction which restores the Program Counter and Flag registers (CPU_PC and CPU_F). The restored Flag register re-enables interrupts because GIE = 1 again. 4. Execution resumes at the next instruction, after the one that occurred before the interrupt. However, if there are more pending interrupts, the subsequent interrupts are processed before the next normal program instruction. Interrupt Latency The time between the assertion of an enabled interrupt and the start of its ISR can be calculated from the following equation. Latency = Time for current instruction to finish + Time for internal interrupt routine to execute + Time for LJMP instruction in interrupt table to execute. For example, if the 5-cycle JMP instruction is executing when an interrupt becomes active, the total number of CPU clock cycles before the ISR begins is as follows: (1 to 5 cycles for JMP to finish) + (13 cycles for interrupt routine) + (7 cycles for LJMP) = 21 to 25 cycles. In the following example, at 12 MHz, 25 clock cycles take 2.08 µs. Interrupt Registers The Interrupt Registers are discussed it the following sections. Interrupt Clear Register The Interrupt Clear Registers (INT_CLRx) are used to enable the individual interrupt sources’ ability to clear posted interrupts. When an INT_CLRx register is read, any bits that are set indicates an interrupt has been posted for that hardware resource. Therefore, reading these registers gives the user the ability to determine all posted interrupts. Page 49 of 70 CYRF69303 Table 69. Interrupt Clear 0 (INT_CLR0) [0xDA] [R/W] Bit # Field Read/Write Default 7 6 GPIO Port 1 Sleep Timer 5 INT1 4 3 2 GPIO Port 0 SPI Receive SPI Transmit 1 0 Reserved POR R/W R/W R/W R/W R/W R/W R/W R/W 0 0 0 0 0 0 0 0 When reading this register: 0 = There is no posted interrupt for the corresponding hardware. 1 = Posted interrupt for the corresponding hardware present. Writing a ‘0’ to the bits clears the posted interrupts for the corresponding hardware. Writing a ‘1’ to the bits and to the ENSWINT (Bit 7 of the INT_MSK3 Register) posts the corresponding hardware interrupt. The GPIO interrupts are edge-triggered. Table 70. Interrupt Clear 1 (INT_CLR1) [0xDB] [R/W] Bit # 7 6 5 Reserved Prog Interval Timer 1 ms Programmable Interrupt Read/Write - R/W R/W – – Default 0 0 0 0 0 Field 4 3 2 1 0 – – – 0 0 0 Reserved When reading this register: 0 = There is no posted interrupt for the corresponding hardware. 1 = Posted interrupt for the corresponding hardware present. Writing a ‘0’ to the bits clears the posted interrupts for the corresponding hardware. Writing a ‘1’ to the bits AND to the ENSWINT. Bit 7 Reserved Table 71. Interrupt Clear 2 (INT_CLR2) [0xDC] [R/W] Bit # 7 6 5 4 3 2 1 0 Reserved Reserved Reserved GPIO Port2 Reserved INT2 16-bit Counter Wrap Reserved Read/Write – – – R/W – R/W R/W – Default 0 0 0 0 0 0 0 0 Field When reading this register: 0 = There is no posted interrupt for the corresponding hardware 1 = Posted interrupt for the corresponding hardware present. Writing a ‘0’ to the bits clears the posted interrupts for the corresponding hardware. Writing a ‘1’ to the bits AND to the ENSWINT (Bit 7 of the INT_MSK3 Register) posts the corresponding hardware interrupt. Bits 7,6,5,3,0Reserved Document Number: 001-66502 Rev. *D Page 50 of 70 CYRF69303 Interrupt Mask Registers The Interrupt Mask Registers (INT_MSKx) are used to enable the individual interrupt sources’ ability to create pending interrupts. There are four Interrupt Mask Registers (INT_MSK0, INT_MSK1, INT_MSK2, and INT_MSK3) that may be referred to in general as INT_MSKx. If cleared, each bit in an INT_MSKx register prevents a posted interrupt from becoming a pending interrupt (input to the priority encoder). However, an interrupt can still post even if its mask bit is zero. All INT_MSKx bits are independent of all other INT_MSKx bits. If an INT_MSKx bit is set, the interrupt source associated with that mask bit may generate an interrupt that becomes a pending interrupt. The Enable Software Interrupt (ENSWINT) bit in INT_MSK3[7] determines the way an individual bit value written to an INT_CLRx register is interpreted. When is cleared, writing 1's to an INT_CLRx register has no effect. However, writing 0's to an INT_CLRx register, when ENSWINT is cleared causes the corresponding interrupt to clear. If the ENSWINT bit is set, any 0's written to the INT_CLRx registers are ignored. However, 1's written to an INT_CLRx register, while ENSWINT is set, cause an interrupt to post for the corresponding interrupt. Software interrupts can aid in debugging interrupt service routines by eliminating the need to create system level interactions that are sometimes necessary to create a hardware-only interrupt. Table 72. Interrupt Mask 3 (INT_MSK3) [0xDE] [R/W] Bit # 7 Field ENSWINT 6 5 4 3 2 1 0 Reserved Read/Write R – – – – – – – Default 0 0 0 0 0 0 0 0 Bit 7 Enable Software Interrupt (ENSWINT) 0 = Disable. Writing 0's to an INT_CLRx register, when ENSWINT is cleared, cause the corresponding interrupt to clear 1 = Enable. Writing 1's to an INT_CLRx register, when ENSWINT is set, cause the corresponding interrupt to post Bits 6:0 Reserved Table 73. Interrupt Mask 2 (INT_MSK2) [0xDF] [R/W] Bit # 7 6 5 4 3 2 1 0 Reserved Reserved Reserved GPIO Port 2 Int Enable Reserved INT2 Int Enable 16-bit Counter Wrap Int Enable Reserved Read/Write – – – R/W – R/W R/W – Default 0 0 0 0 0 0 0 0 Field Bit 7: Reserved Bit 6: Reserved Bit 5: Reserved Bit 4: GPIO Port 2 Interrupt Enable 0 = Mask GPIO Port 2 interrupt 1 = Unmask GPIO Port 2 interrupt Bit 3: Reserved Bit 2: INT2 Interrupt Enable 0 = Mask INT2 interrupt 1 = Unmask INT2 interrupt Bit 1: 16-bit Counter Wrap Interrupt Enable 0 = Mask 16-bit Counter Wrap interrupt 1 = Unmask 16-bit Counter Wrap interrupt Bit 0: Reserved The GPIO interrupts are edge-triggered. Document Number: 001-66502 Rev. *D Page 51 of 70 CYRF69303 Table 74. Interrupt Mask 1 (INT_MSK1) [0xE1] [R/W] Bit # 7 6 5 Reserved Prog Interval Timer Int Enable 1 ms Timer Int Enable R/W R/W R/W – – 0 0 0 0 0 4 3 2 Field Read/Write Default 4 3 2 1 0 – – – 0 0 0 Reserved Bit 7 Reserved Bit 6 Prog Interval Timer Interrupt Enable 0 = Mask Prog Interval Timer interrupt 1 = Unmask Prog Interval Timer interrupt Bit 5 1 ms Timer Interrupt Enable 0 = Mask 1 ms interrupt 1 = Unmask 1 ms interrupt Bit 4:0 Reserved Table 75. Interrupt Mask 0 (INT_MSK0) [0xE0] [R/W] Bit # 7 6 5 Field GPIO Port 1 Int Enable Sleep Timer Int Enable INT1 Int Enable R/W R/W R/W R/W R/W 0 0 0 0 0 Read/Write Default Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 1 0 Reserved POR Int Enable R/W R/W R/W 0 0 0 GPIO Port 0 SPI Receive SPI Transmit Int Enable Int Enable Int Enable GPIO Port 1 Interrupt Enable 0 = Mask GPIO Port 1 interrupt 1 = Unmask GPIO Port 1 interrupt Sleep Timer Interrupt Enable 0 = Mask Sleep Timer interrupt 1 = Unmask Sleep Timer interrupt INT1 Interrupt Enable 0 = Mask INT1 interrupt 1 = Unmask INT1 interrupt GPIO Port 0 Interrupt Enable 0 = Mask GPIO Port 0 interrupt 1 = Unmask GPIO Port 0 interrupt SPI Receive Interrupt Enable 0 = Mask SPI Receive interrupt 1 = Unmask SPI Receive interrupt SPI Transmit Enable 0 = Mask SPI Transmit interrupt 1 = Unmask SPI Transmit interrupt Reserved POR Interrupt Enable 0 = Mask POR interrupt 1 = Unmask POR interrupt Document Number: 001-66502 Rev. *D Page 52 of 70 CYRF69303 Interrupt Vector Clear Register Table 76. Interrupt Vector Clear Register (INT_VC) [0xE2] [R/W] Bit # 7 6 5 Field Read/Write Default 4 3 2 1 0 Pending Interrupt [7:0] R/W R/W R/W R/W R/W R/W R/W R/W 0 0 0 0 0 0 0 0 The Interrupt Vector Clear Register (INT_VC) holds the interrupt vector for the highest priority pending interrupt when read, and when written clears all pending interrupts. Bits 7:0 Pending Interrupt [7:0] 8-bit data value holds the interrupt vector for the highest priority pending interrupt. Writing to this register clears all pending interrupts. Document Number: 001-66502 Rev. *D Page 53 of 70 CYRF69303 Microcontroller Function Register Summary Addr Name 7 6 5 4 3 2 1 0 R/W Default 00 P0DATA P0.7 Reserved Reserved P0.4/INT2 P0.3/INT1 Reserved P0.1 Reserved b--bb-b- 00000000 01 P1DATA P1.7 P1.6/SMISO P1.5/SMOSI P1.4/SCLK P1.3/SSEL P1.2 P1.1 P1.0 bbbbbbb- 00000000 02 P2DATA 06 P01CR 08–09 P03CR– P04CR 0C P07CR Reserved 0D P10CR 0E Reserved Reserved Int Enable P2.1–P2.0 ------bb 00000000 Int Act Low TTL Thresh High Sink Open Drain Pull-up Enable Output Enable bbbbbbbb 00000000 Int Act Low TTL Thresh Reserved Open Drain Pull-up Enable Output Enable --bb-bbb 00000000 Int Enable Int Act Low TTL Thresh Reserved Open Drain Pull-up Enable Output Enable -bbb-bbb 00000000 Reserved Int Enable Int Act Low 5K pullup Enable Output enable bbb----b 00000000 P11CR Reserved Int Enable Int Act Low Open Drain Reserved Output Enable -bb--b-b 00000000 0F P12CR CLK Output Int Enable Int Act Low TTL Threshold Reserved Open Drain Pull-up Enable Output Enable bbbb-bbb 00000000 10 P13CR Reserved Int Enable Int Act Low Reserved High Sink Open Drain Pull-up Enable Output Enable -bb-bbbb 00000000 11–13 P14CR– P16CR SPI Use Int Enable Int Act Low Reserved High Sink Open Drain Pull-up Enable Output Enable bbb-bbbb 00000000 14 P17CR Reserved Int Enable Int Act Low Reserved High Sink Open Drain Pull-up Enable Output Enable -bb-bbbb 00000000 15 P2CR Reserved Int Enable Int Act Low TTL Thresh High Sink Open Drain Pull-up Enable Output Enable -bbbbbbb 00000000 Reserved Reserved Reserved 20 FRTMRL Free Running Timer [7:0] bbbbbbbb 00000000 21 FRTMRH Free Running Timer [15:8] bbbbbbbb 00000000 26 PITMRL Prog Interval Timer [7:0] rrrrrrrr 00000000 27 PITMRH 28 PIRL 29 PIRH 30 CPUCLKCR 31 TMRCLKCR 34 IOSCTR 36 LPOSCTR 3C SPIDATA 3D Reserved Prog Interval Timer [11:8] Prog Interval [7:0] Reserved Prog Interval [11:8] Reserved TCAPCLK Divider TCAPCLK Select ITMRCLK Divider foffset[2:0] ITMRCLK Select Gain[4:0] 32 kHz Low Power Reserved 32 kHz Bias Trim [1:0] 32 kHz Freq Trim [3:0] SPICR Swap LSB First Comm Mode DA INT_CLR0 GPIO Port 1 Sleep Timer INT1 DB INT_CLR1 Reserved Prog Interval Timer 1 ms Timer DC INT_CLR2 Reserved Reserved Reserved GPIO Port 2 DE INT_MSK3 ENSWINT DF INT_MSK2 Reserved Reserved Reserved GPIO Port 2 Int Enable E0 INT_MSK0 GPIO Port 1 Int Enable Sleep Timer Int Enable INT1 Int Enable GPIO Port 0 Int Enable E1 INT_MSK1 Prog Interval Timer Int Enable 1 ms Timer Int Enable SPIData[7:0] Reserved GPIO Port 0 CPOL CPHA SPI Receive SPI Transmit SCLK Select Reserved POR Reserved Reserved ----rrrr 00000000 bbbbbbbb 00000000 ----rrrr 00000000 -------- 00000000 bbbbbbbb 10001111 bbbbbbbb 000ddddd 0-bbbbbb d-dddddd bbbbbbbb 00000000 bbbbbbbb 00000000 bbbbbb-b 00000000 -bb----- 00000000 INT2 16-bit Counter Wrap Reserved ---b-bb- 00000000 r------- 00000000 Reserved INT2 Int Enable 16-bit Counter Wrap Int Enable Reserved ---b-bb- 00000000 SPI Receive Int Enable SPI Transmit Int Enable Reserved POR Int Enable bbbbbb-b 00000000 -bb----- 00000000 bbbbbbbb 00000000 Reserved Reserved E2 INT_VC Pending Interrupt [7:0] E3 RESWDT Reset Watchdog Timer [7:0] -- CPU_A Temporary Register T1 [7:0] -------- 00000000 -- CPU_X X[7:0] -------- 00000000 wwwwwwww 00000000 -- CPU_PCL Program Counter [7:0] -------- 00000000 -- CPU_PCH Program Counter [15:8] -------- 00000000 Document Number: 001-66502 Rev. *D Page 54 of 70 CYRF69303 Microcontroller Function Register Summary (continued) Addr Name -- CPU_SP 7 6 5 4 3 2 1 0 Stack Pointer [7:0] F7 CPU_F FF CPU_SCR Reserved 1E0 OSC_CR0 Reserved 1E3 PORCR Reserved 1E4 VLTCMP 1EB ECO_TR GIES Reserved WDRS No Buzz Document Number: 001-66502 Rev. *D Default 00000000 00000010 XIO Super Carry Zero Global IE ---brbbb PORS Sleep Reserved Reserved Stop r-ccb--b 00010100 --bbbbbb 00001000 Sleep Timer [1:0] CPU Speed [2:0] PORLEV[1:0] Reserved Reserved Sleep Duty Cycle [1:0] R/W -------- PPOR Reserved --bb-bbb 00000000 ------rr 00000000 bb------ 00000000 Page 55 of 70 CYRF69303 Radio Function Register Summary Address 0x00 0x01 Mnemonic CHANNEL_ADR TX_LENGTH_ADR b7 Not Used b6 0x02 TX_CTRL_ADR TX GO TX CLR 0x03 TX_CFG_ADR Not Used OS IRQ Not Used RSVD 0x04 TX_IRQ_STATUS_ADR 0x05 0x06 RX_CTRL_ADR RX_CFG_ADR 0x07 0x08 0x09 0x0A 0x0B RX_IRQ_STATUS_ADR RX_STATUS_ADR RX_COUNT_ADR RX_LENGTH_ADR PWR_CTRL_ADR 0x0C 0x0D 0x0E 0x0F 0x10 0x11 0x12 0x13 0x14 0x15 0x16 0x17 0x18 0x19 0x1A 0x1B 0x1C 0x1D XTAL_CTRL_ADR IO_CFG_ADR GPIO_CTRL_ADR XACT_CFG_ADR FRAMING_CFG_ADR DATA32_THOLD_ADR DATA64_THOLD_ADR RSSI_ADR EOP_CTRL_ADR [9] CRC_SEED_LSB_ADR CRC_SEED_MSB_ADR TX_CRC_LSB_ADR TX_CRC_MSB_ADR RX_CRC_LSB_ADR RX_CRC_MSB_ADR TX_OFFSET_LSB_ADR TX_OFFSET_MSB_ADR MODE_OVERRIDE_ADR 0x1E RX GO AGC EN RXOW IRQ RX ACK b5 TXB15 IRQEN DATA CODE LENGTH TXB15 IRQ RXB16 IRQEN b4 b3 Channel TX Length TXB8 TXB0 IRQEN IRQEN RSVD Data mode b2 b1 b0 TXBERR IRQEN TXC IRQEN TXE IRQEN PA SETTING TXB0 TXBERR TXC TXE IRQ IRQ IRQ IRQ RXB1 RXBERR RXC RXE RSVD IRQEN IRQEN IRQEN IRQEN FAST TURN LNA ATT HILO EN Not Used RXOW EN VLD EN SOPDET RXB16 RXB8 RXB1 RXBERR RXC RXE IRQ IRQ IRQ IRQ IRQ IRQ IRQ PKT ERR EOP ERR CRC0 Bad CRC RX Code RX Data Mode RX Count RX Length The firmware should set “00010000” to this register while initiating XOUT FN IRQ OD IRQ POL XOUT OP MISO OP ACK EN Not Used SOP EN SOP LEN Not Used Not Used Not Used Not Used SOP Not Used HEN XSIRQ EN MISO OD RSVD FRC END LEN EN Not Used Not Used LNA HINT TXB8 IRQ RXB8 IRQEN Not Used XOUT OD IRQ OP Not Used RSVD XOUT IP END STATE RSVD MISO IP SOP TH TH32 TH64 RSSI EOP Not Used CRC SEED LSB CRC SEED MSB CRC LSB CRC MSB CRC LSB CRC MSB STRIM LSB Not Used STRIM MSB FRC AWAKE Not Used Not Used FRC RXDR DIS CRC0 DIS RXCRC ACE MAN TXACK OVRD ACK DIS TXCRC RSVD RSVD START DLY RSVD RSVD Not Used RSVD Not Used RSVD Not Used FRC SEN RX_OVERRIDE_ADR ACK RX RXTX DLY MAN RXACK 0x1F 0x26 TX_OVERRIDE_ADR XTAL_CFG_ADR ACK TX RSVD FRC PRE RSVD RSVD RSVD 0x27 CLK_OVERRIDE_ADR RSVD RSVD RSVD RSVD RSVD RSVD 0x28 CLK_EN_ADR RSVD RSVD RSVD RSVD RSVD 0x29 RX_ABORT_ADR RSVD RSVD ABORT EN RSVD RSVD 0x32 AUTO_CAL_TIME_ADR 0x35 AUTO_CAL_OFFSET_ADR 0x39 ANALOG_CTRL_ADR RSVD RSVD RSVD FREQ SPI 3PIN IRQ GPIO RSVD IRQ IP ACK TO RST Default[4] -1001000 00000000 00000011 Access[4] -bbbbbbb bbbbbbbb bbbbbbbb --000101 --bbbbbb -------- rrrrrrrr 00000111 bbbbbbbb 10010-10 bbbbb-bb -------- brrrrrrr -------00000000 00000000 10100000 rrrrrrrr rrrrrrrr rrrrrrrr bbb-bbbb 000--100 00000000 0000---1-000000 10100101 ----0100 ---01010 0-100000 10100100 00000000 00000000 --------------11111111 11111111 00000000 ----0000 00000--0 0000000- bbb--bbb bbbbbbbb bbbbrrrr b-bbbbbb bbbbbbbb ----bbbb ---bbbbb r-rrrrrr bbbbbbbb bbbbbbbb bbbbbbbb rrrrrrrr rrrrrrrr rrrrrrrr rrrrrrrr bbbbbbbb ----bbbb wwwww--w bbbbbbb- Not Used 00000000 bbbbbbbb TX INV RSVD 00000000 RXF RSVD 00000000 RSVD RXF RSVD 00000000 RSVD RSVD RSVD 00000000 wwwwwww w wwwwwww w wwwwwww w wwwwwww w wwwwwww w wwwwwww w wwwwwww w AUTO_CAL_TIME 00000011 AUTO_CAL_OFFSET 00000000 RSVD RSVD RSVD RX INV ALL SLOW 00000000 Register Files 0x20 TX_BUFFER_ADR TX Buffer File -------- 0x21 0x22 0x23 0x24 0x25 RX Buffer File SOP Code File Data Code File Preamble File MFG ID File -------Note [5] Note [6] Note [7] NA RX_BUFFER_ADR SOP_CODE_ADR DATA_CODE_ADR PREAMBLE_ADR MFG_ID_ADR wwwwwww w rrrrrrrr bbbbbbbb bbbbbbbb bbbbbbbb rrrrrrrr All registers are read and writable, except where noted. Registers may be written to or read from either individually or in sequential groups. A single-byte read or write reads or writes from the addressed register. Incrementing burst read and write is a sequence that begins with an address, and then reads or writes to/from each register in address order for as long as clocking continues. It is possible to repeatedly read (poll) a single register using a nonincrementing burst read. Notes 4. b = read/write; r = read only; w = write only; ‘-’ = not used, default value is undefined. 5. SOP_CODE_ADR default = 0x17FF9E213690C782. 6. DATA_CODE_ADR default = 0x02F9939702FA5CE3012BF1DB0132BE6F. 7. PREAMBLE_ADR default = 0x333302 8. Registers must be configured or accessed only when the radio is in IDLE or SLEEP mode.The GPIOs, RSSI registers can be accessed in Active Tx and Rx mode. 9. EOP_CTRL_ADR[6:4] must never have the value of “000” i.e. EOP Hint Symbol count must never be “0” Document Number: 001-66502 Rev. *D Page 56 of 70 CYRF69303 DC voltage to logic inputs [10] ............... –0.3 V to VIO +0.3 V Absolute Maximum Ratings Exceeding maximum ratings may shorten the useful life of the device. User guidelines are not tested. Storage temperature .................................. –40 °C to +90 °C Ambient temperature with power applied ...... 0 °C to +70 °C Supply voltage on any power supply pin relative to VSS ........................................–0.3 V to +3.9 V DC voltage applied to outputs in High-Z state ...................................... –0.3 V to VIO +0.3 V Static discharge voltage (Digital) [11] ........................ >2000 V Static discharge voltage (RF) [11] ............................... 1100 V Latch up current ......................................+200 mA, –200 mA Ground voltage ................................................................ 0 V FOSC (Crystal frequency) ........................... 12 MHz ±30 ppm DC Characteristics (T = 25 C) Parameter Description VBAT Battery voltage VIO VIO voltage VCC VCC voltage Conditions 0–70 C 0–70 C Min Typ Max Unit 2.7 – 3.6 V 2.7 – 3.6 V 2.7 – 3.6 V Device Current (For total current consumption in different modes, for example Radio, active, MCU, and sleep, add Radio Function Current and MCU Function Current) ICC (GFSK)[12] Average ICC, 1 Mbps, slow channel PA = 5, 2-way, 4 bytes/10 ms CPU speed = 6 MHz – 9.87 – mA ICC (32-8DR)[12] Average ICC, 250 kbps, fast channel PA = 5, 2-way, 4 bytes/10 ms CPU speed = 6 MHz – 10.2 – mA ISB Sleep Mode ICC VCC = 3.0 V, MCU sleep – 2.72 – µA Notes 10. It is permissible to connect voltages above VIO to inputs through a series resistor limiting input current to 1 mA. AC timing not guaranteed. 11. Human Body Model (HBM). 12. Includes current drawn while starting crystal, starting synthesizer, transmitting packet (including SOP and CRC16), changing to receive mode, and receiving ACK handshake. Device is in sleep except during this transaction. Document Number: 001-66502 Rev. *D Page 57 of 70 CYRF69303 DC Characteristics (continued) (T = 25 C) Parameter Description Conditions Min Typ Max Unit – 1.1 – mA – 8.6 – mA Radio Function Currents (VCC = 3.0 V, MCU Sleep) IDLE ICC Radio off, XTAL Active Isynth ICC during Synth Start XOUT disabled TX ICC ICC during transmit PA = 5 (–5 dBm) – 21.2 – mA TX ICC ICC during transmit PA = 6 (0 dBm) – 28.5 – mA RX ICC ICC during receive LNA off, ATT on. – 18.9 – mA RX ICC ICC during receive LNA on, ATT off. – 21.9 – mA MCU Function Currents (VDD = 3.0 V) IDD1 VDD operating supply current CPU speed = 6 MHz – 5.0 – mA IDD1 VDD operating supply current CPU speed = 3 MHz – 4.4 – mA – V Radio Function GPIO Interface VOH1 Output High voltage condition 1 At IOH = –100.0 µA VIO – 0.1 VIO VOH2 Output High voltage condition 2 At IOH = –2.0 mA VIO – 0.4 VIO – V VOL Output Low voltage At IOL = 2.0 mA – 0 0.4 V VIH Input High voltage 0.76 VIO – VIO V VIL Input Low voltage 0 – 0.24 VIO V IIL Input leakage current 0 < VIN < VIO –1 0.26 +1 µA CIN Pin input capacitance except XTAL, RFN, RFP, RFBIAS – 3.5 10 pF 4 – 12 K MCU Function GPIO Interface RUP Pull-up resistance VICR Input threshold voltage low, CMOS mode Low to High edge 40% – 65% VCC VICF Input threshold voltage low, CMOS mode High to Low edge 30% – 55% VCC VHC Input hysteresis voltage, CMOS High to low edge Mode 3% – 10% VCC VILTTL Input Low voltage, TTL Mode 0.72 V VIHTTL Input HIGH voltage, TTL Mode VOL1 Output Low voltage, High Drive[13] VOL2 Output Low voltage, High Drive[13] VOL3 Output Low voltage, Low Drive VOH Output High voltage[14] – – 1.6 – IOL1 = 50 mA – – 1.4 V IOL1 = 25 mA – – 0.4 V IOL2 = 8 mA – – 0.8 V IOH = 2 mA VCC – 0.5 – V V Notes 13. Available only on P1.3,P1.4,P1.5,P1.6,P1.7. 14. Except for pins P1.0, P1.1 in GPIO mode. Document Number: 001-66502 Rev. *D Page 58 of 70 CYRF69303 AC Characteristics Parameter Description Conditions Min Typ Max Unit GPIO Timing TR_GPIO Output rise time Measured between 10 and 90% Vdd with 50 pF load – – 50 ns TF_GPIO Output fall time Measured between 10 and 90% Vdd with 50 pF load – – 15 ns FIMO Internal main oscillator frequency With proper trim values loaded FILO Internal low power oscillator With proper trim values loaded TSMCK SPI master clock rate FCPUCLK/6 18.72 – 26.4 MHz 15.0001 – 50.0 kHz – – 2 MHz SPI Timing TSSCK SPI slave clock rate – – 2.2 MHz TSCKH SPI clock high time High for CPOL = 0, Low for CPOL = 1 125 – – ns TSCKL SPI clock low time Low for CPOL = 0, High for CPOL = 1 125 – – ns TMDO Master data output time[15] SCK to data valid –25 – 50 ns TMDO1 Master data output time, First bit with CPHA = 0 Time before leading SCK edge 100 – – ns TMSU Master input data setup time 50 – – ns TMHD Master input data hold time 50 – – ns TSSU Slave input data setup time 50 – – ns TSHD Slave input data hold time 50 – – ns TSDO Slave data output time SCK to data valid – – 100 ns TSDO1 Slave data output time, First bit with CPHA = 0 Time after SS LOW to data valid – – 100 ns TSSS Slave select setup time Before first SCK edge 150 – – ns TSSH Slave select hold time After last SCK edge 150 – – ns Note 15. In Master mode first bit is available 0.5 SPICLK cycle before Master clock edge available on the SCLK pin. Document Number: 001-66502 Rev. *D Page 59 of 70 CYRF69303 Switching Waveforms Figure 16. Clock Timing TCYC TCH CLOCK TCL Figure 17. GPIO Timing Diagram 90% GPIO Pin Output Voltage 10% TR_GPIO TF_GPIO Figure 18. SPI Master Timing, CPHA = 1 SS (SS is under firmware control in SPI Master mode) TSCKL SCK (CPOL=0) TSCKH SCK (CPOL=1) TMDO MSB MOSI MISO MSB LSB LSB TMSU TMHD Document Number: 001-66502 Rev. *D Page 60 of 70 CYRF69303 Switching Waveforms (continued) Figure 19. SPI Slave Timing, CPHA = 1 SS TSSS TSSH TSCKL SCK (CPOL=0) TSCKH SCK (CPOL=1) MOSI MSB LSB TSSU TSHD TSDO MSB MISO LSB Figure 20. SPI Master Timing, CPHA = 0 SS (SS is under firmware control in SPI Master mode) TSCKL SCK (CPOL=0) TSCKH SCK (CPOL=1) TMDO TMDO1 MSB MOSI MISO MSB LSB LSB TMSU TMHD Document Number: 001-66502 Rev. *D Page 61 of 70 CYRF69303 Switching Waveforms (continued) Figure 21. SPI Slave Timing, CPHA = 0 SS TSSH TSSS TSCKL SCK (CPOL=0) TSCKH SCK (CPOL=1) MSB MOSI LSB TSSU TSHD TSDO TSDO1 MISO MSB Document Number: 001-66502 Rev. *D LSB Page 62 of 70 CYRF69303 RF Characteristics Table 77. Radio Parameters Parameter Description RF frequency range Conditions Subject to regulation Min Typ Max Unit 2.400 – 2.497 GHz –90 – dBm Receiver (T = 25 °C, VCC = 3.0 V, fOSC = 12.000 MHz, BER < 10–3) Sensitivity 250 kbps 32-8DR BER 1E-3 – Sensitivity GFSK BER 1E-3, ALL SLOW = 1 – –84 – dBm – 22.8 – dB LNA Gain ATT Gain – –31.7 – dB Maximum Received Signal LNA On –15 –6 – dBm RSSI Value for PWRin –60 dBm LNA On – 21 – Count – 1.9 – dB/Count 9 – dB RSSI Slope Interference Performance (CER 1E-3) Co-channel Interference rejection Carrier-to-Interference (C/I) C = –60 dBm – Adjacent (±1 MHz) Channel Selectivity C/I 1 MHz C = –60 dBm – 3 – dB Adjacent (±2 MHz) Channel Selectivity C/I 2 MHz C = –60 dBm – –30 – dB Adjacent (> 3 MHz) Channel Selectivity C/I > 3 MHz C = –67 dBm – –38 – dB Out-of-Band Blocking 30 MHz–12.75 MHz[16] C = –67 dBm – –30 – dBm Intermodulation C = –64 dBm, f = 5,10 MHz – –36 – dBm Receive Spurious Emission 800 MHz 100 kHz ResBW – –79 – dBm 1.6 GHz 100 kHz ResBW – –71 – dBm 3.2 GHz 100 kHz ResBW – –65 – dBm PA = 6 –2 0 +2 dBm Maximum RF transmit power PA = 5 –7 –5 –3 dBm Maximum RF transmit power PA = 0 – –35 – dBm – 35 – dB RF power range control step size Six steps, monotonic – 5.6 – dB Frequency deviation Min PN Code Pattern 10101010 – 270 – kHz Frequency deviation Max PN Code Pattern 11110000 – 323 – kHz Transmitter (T = 25 °C, VCC = 3.0 V, fOSC = 12.000 MHz) Maximum RF transmit power RF power control range Error vector magnitude (FSK error) >0 dBm Occupied bandwidth –6 dBc, 100 kHz ResBW – 10 – %rms 500 876 – kHz Notes 16. Exceptions F/3 and 5C/3. Document Number: 001-66502 Rev. *D Page 63 of 70 CYRF69303 Table 77. Radio Parameters (continued) Parameter Description Conditions Min Typ Max Unit In-band Spurious Second Channel Power (±2 MHz) – –38 – dBm In-band Spurious Third Channel Power (>3 MHz) – –44 – dBm Non-Harmonically Related Spurs (8.000 GHz) – –38 – dBm Non-Harmonically Related Spurs (1.6 GHz) – –34 – dBm Transmit Spurious Emission (PA = 6) Non-Harmonically Related Spurs (3.2 GHz) – –47 – dBm Harmonic Spurs (Second Harmonic) – –43 – dBm Harmonic Spurs (Third Harmonic) – –48 – dBm Fourth and Greater Harmonics – –59 – dBm – 0.7 1.3 ms – 0.6 – ms Power Management (Crystal PN# eCERA GF-1200008) Crystal Start to 10ppm Crystal Start to IRQ XSIRQ EN = 1 Synth Settle Slow channels – – 270 µs Synth Settle Medium channels – – 180 µs Synth Settle Fast channels – – 100 µs Link Turnaround Time GFSK – – 30 µs Link Turnaround Time 250 kbps – – 62 µs Max. packet length < 60 ppm crystal-to-crystal – – 40 bytes Document Number: 001-66502 Rev. *D Page 64 of 70 CYRF69303 Ordering Information Package Ordering Part Number Status 40-pin Pb-free QFN 6 × 6 mm (Sawn) CYRF69303-40LTXC In Production 40-pin Pb-free QFN 6 × 6 mm (Punch) CYRF69303-40LFXC NRND Ordering Code Definitions CY RF 69303 - 40 LX X C Temperature Range: C = Commercial Pb-free Package Type: LX = LT or LF LT = QFN (Sawn Type); LF = QFN (Punch Type) No of pins in package: 40-pin Part Number Marketing Code: RF = Wireless (radio frequency) product line Company ID: CY = Cypress Document Number: 001-66502 Rev. *D Page 65 of 70 CYRF69303 Package Handling Some IC packages require baking before they are soldered onto a PCB to remove moisture that may have been absorbed after leaving the factory. A label on the packaging has details about actual bake temperature and the minimum bake time to remove this moisture.The maximum bake time is the aggregate time that the parts are exposed to the bake temperature. Exceeding this exposure time may degrade device reliability. Table 78. Package Handling Parameter Description TBAKETEMP Bake Temperature tBAKETIME Bake Time Min Typ Max Unit – 125 see package label °C see package label – 24 hours Package Diagrams Figure 22. 40-pin QFN (6 × 6 × 1.00 mm) LT40B 3.5 × 3.5 E-Pad (Sawn) Package Outline, 001-13190 001-13190 *H Document Number: 001-66502 Rev. *D Page 66 of 70 CYRF69303 Package Diagrams (continued) Figure 23. 40-pin QFN (6 × 6 × 1.0 mm) LF40A/LY40A 3.50 × 3.50 E-Pad (Punch) Package Outline, 001-12917 [17] SOLDERABLE EXPOSED PAD 001-12917 *C Note 17. Not Recommended for New Design. Document Number: 001-66502 Rev. *D Page 67 of 70 CYRF69303 Acronyms Document Conventions Table 79. Acronyms Used in this Document Units of Measure Acronym Description Table 80. Units of Measure ACK Acknowledge (packet received, no errors) BER Bit Error Rate °C degree Celsius BOM Bill Of Materials dB decibels CMOS Complementary Metal Oxide Semiconductor dBc decibel relative to carrier CRC Cyclic Redundancy Check dBm decibel-milliwatt FEC Forward Error Correction Hz hertz FER Frame Error Rate KB 1024 bytes GFSK Gaussian Frequency-Shift Keying Kbit 1024 bits HBM Human Body Model kHz kilohertz ISM Industrial, Scientific, and Medical k kilohm IRQ Interrupt Request MHz megahertz MCU Microcontroller Unit M megaohm NRZ Non Return to Zero A microampere PLL Phase-Locked Loop s microsecond QFN Quad Flat No-lead V microvolt RSSI Received Signal Strength Indication Vrms microvolts root-mean-square RF Radio Frequency W microwatt Rx Receive mA milliampere Tx Transmit ms millisecond mV millivolt nA nanoampere ns nanosecond nV nanovolt ohm pp peak-to-peak ppm parts per million ps picosecond sps samples per second V volt Document Number: 001-66502 Rev. *D Symbol Unit of Measure Page 68 of 70 CYRF69303 Document History Page Document Title: CYRF69303, Programmable Radio-on-Chip LPstar Document Number: 001-66502 Rev. ECN Orig. of Change Submission Date ** 3188093 NXZ / KKCN 04/05/11 *A 3333406 KPMD 08/01/2011 Changed status from Advance to Final. Post to external web. *B 3532316 KKCN 02/28/2012 Updated Ordering Information (Added MPN CYRF69303-40LTXC) and added Ordering Code Definitions. Updated Package Diagrams (Added spec 001-44328). *C 3735882 ANKC 09/06/2012 Updated Ordering Information (No change in part numbers, included a column “Status”). Updated Package Diagrams (No change in revisions of specs, added Note 17 and referred the same note in Figure 23). Updated in new template. *D 3983149 ANKC 04/27/2013 Updated Pin Definitions (Updated Name and Function of Pin 21 and Pin 22). Updated Package Diagrams (Replaced spec 001-44328 *F with spec 001-13190 *H). Completing Sunset Review. Document Number: 001-66502 Rev. *D Description of Change New data sheet. Page 69 of 70 CYRF69303 Sales, Solutions, and Legal Information Worldwide Sales and Design Support Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives, and distributors. To find the office closest to you, visit us at Cypress Locations. Products Automotive Clocks & Buffers Interface Lighting & Power Control PSoC Solutions cypress.com/go/automotive cypress.com/go/clocks psoc.cypress.com/solutions cypress.com/go/interface PSoC 1 | PSoC 3 | PSoC 5 cypress.com/go/powerpsoc cypress.com/go/plc Memory PSoC Touch Sensing USB Controllers Wireless/RF cypress.com/go/memory cypress.com/go/psoc cypress.com/go/touch cypress.com/go/USB cypress.com/go/wireless © Cypress Semiconductor Corporation, 2011-2013. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be used for medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges. Any Source Code (software and/or firmware) is owned by Cypress Semiconductor Corporation (Cypress) and is protected by and subject to worldwide patent protection (United States and foreign), United States copyright laws and international treaty provisions. Cypress hereby grants to licensee a personal, non-exclusive, non-transferable license to copy, use, modify, create derivative works of, and compile the Cypress Source Code and derivative works for the sole purpose of creating custom software and or firmware in support of licensee product to be used only in conjunction with a Cypress integrated circuit as specified in the applicable agreement. Any reproduction, modification, translation, compilation, or representation of this Source Code except as specified above is prohibited without the express written permission of Cypress. Disclaimer: CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Cypress reserves the right to make changes without further notice to the materials described herein. Cypress does not assume any liability arising out of the application or use of any product or circuit described herein. Cypress does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress’ product in a life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges. Use may be limited by and subject to the applicable Cypress software license agreement. Document Number: 001-66502 Rev. *D Revised April 27, 2013 All products and company names mentioned in this document may be the trademarks of their respective holders. Page 70 of 70