Operational Amplifiers / Comparators Ground Sense Comparators BA10393F,BA10339F,BA10339FV,BA2903SF,BA2903SFV,BA2903SFVM BA2903F,BA2903FV,BA2903FVM,BA2901SF,BA2901SFV,BA2901SKN, BA2901F,BA2901FV,BA2901KN,BA8391G No.11049EBT18 ●Description General purpose BA8391G/BA10393/BA10339 family and high reliability BA2903/BA2901 family integrate one, two or four independent high gain voltage comparator. Some features are the wide operating voltage that is 2 to 36[V] (for BA8391G, BA10393, BA2903, BA2901 family), 3 to 36[V] (for BA10339 family) and low supply current. Therefore, this series is suitable for any application. High Speed High Reliability Single BA8391G Dual BA10393F Quad BA10339F/FV Dual BA2903S F/FV/FVM :105℃ guaranteed BA2903 F/FV/FVM :125℃ guaranteed BA2901S F/FV/KN :105℃ guaranteed BA2901 F/FV/KN :125℃ guaranteed Quad ●Features 1) Operable with a signal power supply 2) 5) Wide operating supply voltage Internal ESD protection Human body model (HBM)±5000[V](Typ.) +2.0[V] ~ +36.0[V] (single supply) ±1.0[V] ~ ±18.0[V] (split supply) +3.0[V] ~ +36.0[V] (single supply) ±1.5[V] ~ ±18.0[V] (split supply) +2.0[V] ~ +36.0[V] (single supply) (BA10393 family) (BA8391/BA2903/BA2901 family) 6) Gold PAD (BA2903/BA2901 family) (BA10339 family) 7) (BA2903/BA2901 family) ±1.0[V] ~ ±18.0[V] (split supply) 3) Standard comparator pin-assignments 4) Input and output are operable ground sense Wide temperature range -40[℃] ~ +85[℃](BA8391G/BA10393/BA10339 family) -40[℃] ~ +105[℃](BA2903S/BA2901S family) -40[℃] ~ +125[℃](BA2903/BA2901 family) ●Pin Assignment OUT1 1 -IN VEE 2 +IN 5 VCC 1 + 4 OUT 3 -IN1 2 +IN1 3 VEE 4 8 VCC 7 OUT2 CH1 - + CH2 + - OUT2 1 14 OUT3 OUT1 2 13 OUT4 VCC 3 12 VEE -IN1 4 6 -IN2 5 +IN2 +IN1 5 -IN2 6 +IN2 CH1 - + CH4 - + 11 +IN4 10 -IN4 CH2 - + 7 CH3 - + 9 +IN3 8 -IN3 OUT1 OUT2 OUT3 OUT4 16 15 14 13 12 VEE VCC 1 NC 2 -IN1 3 CH1 - + BA8391G SOP8 BA10393F BA2903SF BA2903F www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. SSOP-B8 MSOP8 BA2903SFV BA2903SFVM BA2903FV BA2903FVM 1/24 SOP14 BA10339F BA2901SF BA2901F SSOP-B14 BA10339FV BA2901SFV BA2901FV CH3 - + CH4 - + 11 NC 10 +IN4 9 -IN4 +IN1 4 5 -IN2 SSOP5 CH2 - + 6 7 +IN2 -IN3 8 +IN3 VQFN16 BA2901SKN BA2901KN 2011.08 - Rev.B BA10393F,BA10339F,BA10339FV,BA2903SF,BA2903SFV,BA2903SFVM,BA2903F,BA2903FV, BA2903FVM,BA2901SF,BA2901SFV,BA2901SKN,BA2901F,BA2901FV,BA2901KN,BA8391G Technical Note ●Absolute Maximum Ratings (Ta=25[℃]) Parameter Ratings Symbol Supply Voltage BA8391G BA10393 family VCC-VEE Differential Input Voltage (*1) BA10339 family +36 Unit V Vid ±36 VCC - VEE V Input Common-mode Voltage Range Vicm (VEE-0.3)~VEE+36 (VEE-0.3)~VCC V Operating Temperature Range Topr Storage Temperature Range Tstg -55 ~ +150 -55 ~ +125 ℃ Maximum junction Temperature Tjmax +150 +125 ℃ -40 ~ +85 ℃ Note: Absolute maximum rating item indicates the condition which must not be exceeded. Application if voltage in excess of absolute maximum rating or use out of absolute maximum rated temperature environment may cause deterioration of characteristics. (*1) The voltage difference between inverting input and non-inverting input is the differential input voltage. Then input terminal voltage is set to more than VEE. ●Electric Characteristics ○BA8391G (Unless otherwise specified VCC=+5[V], VEE=0[V], Ta=25[℃]) Limits Parameter Symbol Temperature range 25℃ Input Offset Voltage (*2) (*3) Unit BA8391G Min. Typ. Max. - 2 7 Vio Condition VOUT = 1.4[V] mV Full range - - 15 25℃ - 5 50 Full range - - 200 25℃ - 50 250 Full range - - 500 Vicm 25℃ 0 - VCC-1.5 V - Large Signal Voltage Gain AV 25℃ 88 100 - dB VCC=15[V], VOUT=1.4 ~ 11.4[V], RL = 15[kΩ], VRL = 15[V] Supply Current (*3) 25℃ - 0.3 0.7 ICC Input Offset Current (*2) (*3) Iio Input Bias Current (*2) (*3) Input Common-mode Voltage Range Ib Output Sink Current(*4) IOL Output Saturation Voltage (*3) (Low level output voltage) VOL Output Leakage Current (*3) (High level output voltage) nA VOUT = 1.4[V] nA VOUT = 1.4[V] VOUT = open mA Full range - - 1.3 25℃ 6 16 - 25℃ - 150 400 VOUT = open, VCC = 36[V] mA VIN+ = 0[V], VIN- = 1[V], VOL = 1.5[V] mV VIN+ = 0[V], VIN- = 1[V], IOL = 4[mA] Full range - - 700 25℃ - 0.1 - nA Full range - - 1 μA - 1.3 - Ileak Response Time (*2) (*3) (*4) VCC = 5 ~ 36[V], VOUT = 1.4[V] Tre 25℃ μs VIN+ = 1[V], VIN- = 0[V], VOH = 5[V] VIN+ = 1[V], VIN- = 0[V], VOH = 36[V] RL = 5.1[kΩ], VRL = 5[V], VIN=100[mVp-p],overdrive=5[mV] RL =5.1[kΩ], VRL=5[V], VIN=TTL Logic Swing, VREF = 1.4[V] Absolute value Full range Ta=-40 ~ +85[℃] Under high temperatures, please consider the power dissipation when selecting the output current. When the output terminal is continuously shorted the output current reduces the internal temperature by flushing. www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 2/24 2011.08 - Rev.B BA10393F,BA10339F,BA10339FV,BA2903SF,BA2903SFV,BA2903SFVM,BA2903F,BA2903FV, BA2903FVM,BA2901SF,BA2901SFV,BA2901SKN,BA2901F,BA2901FV,BA2901KN,BA8391G Technical Note ○BA10393 family(Unless otherwise specified VCC=+5[V], VEE=0[V], Ta=25[℃]) Limits Parameter Symbol Temperature range BA10393 family Unit Min. Typ. Max. Condition Input Offset Voltage (*5) Vio 25℃ - 1 5 mV VOUT = 1.4[V] Input Offset Current (*5) Iio 25℃ - 5 50 nA VOUT = 1.4[V] Input Bias Current (*6) Ib 25℃ - 50 250 nA VOUT = 1.4[V] Input Common-mode Voltage Range Vicm 25℃ 0 - VCC-1.5 V - Large Signal Voltage Gain AV 25℃ 93 106 - dB RL = 15[kΩ], VCC = 15[V], VRL = 15[V], VOUT = 1.4~11.4[V] Supply Current ICC 25℃ - 0.4 1 mA RL = ∞ All Comparators Output Sink Current IOL 25℃ 6 16 - mA Output Saturation Voltage (Low level output voltage) VOL 25℃ - 250 400 mV Output Leakage Current (High level output voltage) 25℃ - 0.1 - μA Ileak 25℃ - - 1 μA 25℃ - 1.3 - μs Response Time (*5) (*6) Tre VIN- = 1[V], VIN+ = 0[V], VOL = 1.5[V] VIN- = 1[V], VIN+ = 0[V], IOL = 4[mA] VIN- = 0[V], VIN+ = 1[V], VOH = 5[V] VIN- = 0[V], VIN+ = 1[V], VOH = 36[V] RL = 5.1[kΩ], VRL = 5[V] VIN=100[mVp-p],overdrive=5[mV] Absolute value Current Direction: Since first input stage is composed with PNP transistor, input bias current flows out of IC. ○BA10339 family(Unless otherwise specified VCC=+5[V], VEE=0[V], Ta=25[℃]) Limits Parameter Symbol Temperature range BA10339 family Unit Min. Typ. Max. Condition Input Offset Voltage (*7) Vio 25℃ - ±1 ±5 mV VOUT = 1.4[V] Input Offset Current (*7) Iio 25℃ - ±5 ±50 nA VOUT = 1.4[V] Input Bias Current (*8) Ib 25℃ - 50 250 nA VOUT = 1.4[V] Input Common-mode Voltage Range Vicm 25℃ 0 - VCC-1.5 V Large Signal Voltage Gain AV 25℃ 93 106 - dB RL = 15[kΩ],VCC = 15[V] Supply Current ICC 25℃ - 0.8 2 mA RL = ∞ All Comparators Output Sink Current IOL 25℃ 6 16 - mA Output Saturation Voltage (Low level output voltage) VOL 25℃ - 250 400 mV Output Leakage Current (High level output voltage) 25℃ - 0.1 - μA Ileak 25℃ - - 1 μA 25℃ - 1.3 - μs Response Time Tre - VIN- = 1[V], VIN+ = 0[V], VOUT = 1.5[V] VIN- = 1[V], VIN+ = 0[V], IOL = 4[mA] VIN- = 0[V], VIN+ = 1[V], VOUT = 5[V] VIN- = 0[V], VIN+ = 1[V], VOUT = 36[V] RL = 5.1[kΩ], VRL = 5[V] VIN=100[mVp-p],overdrive=5[mV] (*7) Absolute value (*8) Current Direction : Since first input stage is composed with PNP transistor, input bias current flows out of IC. www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 3/24 2011.08 - Rev.B BA10393F,BA10339F,BA10339FV,BA2903SF,BA2903SFV,BA2903SFVM,BA2903F,BA2903FV, BA2903FVM,BA2901SF,BA2901SFV,BA2901SKN,BA2901F,BA2901FV,BA2901KN,BA8391G Technical Note ●Absolute Maximum Ratings (Ta=25[℃]) Ratings Parameter Symbol Supply Voltage BA2903S family BA2901S family BA2903 family BA2901 family Unit VCC-VEE +36 V Vid ±36 V Input Common-mode Voltage Range Vicm (VEE-0.3) ~ VEE+36 V Operating Temperature Range Topr Storage Temperature Range Tstg -55 ~ +150 ℃ Tjmax +150 ℃ Differential Input Voltage (*9) Maximum junction Temperature -40 ~ +105 -40 ~ +125 ℃ Note: Absolute maximum rating item indicates the condition which must not be exceeded. Application if voltage in excess of absolute maximum rating or use out of absolute maximum rated temperature environment may cause deterioration of characteristics. (*9) The voltage difference between inverting input and non-inverting input is the differential input voltage. Then input terminal voltage is set to more than VEE. ○BA2903 family(Unless otherwise specified VCC=+5[V], VEE=0[V], Ta=25[℃]) Limits Parameter Symbol Temperature range 25℃ Input Offset Voltage (*10) (*11) BA2903S F/FV/FVM BA2903F/FV/FVM Min. Typ. Max. - 2 7 Vio Unit Condition VOUT = 1.4[V] mV Full range - - 15 25℃ - 5 50 Full range - - 200 25℃ - 50 250 Full range - - 500 Vicm 25℃ 0 - VCC-1.5 V - Large Signal Voltage Gain AV 25℃ 88 100 - dB VCC = 15[V], VOUT=1.4 ~ 11.4[V] RL = 15[kΩ], VRL = 15[V] Supply Current (*11) 25℃ - 0.6 1 ICC Input Offset Current (*10) (*11) Iio Input Bias Current (*10) (*11) Ib Input Common-mode Voltage Range Output Sink Current(*12) IOL Output Saturation Voltage (*11) (Low level output voltage) VOL Output Leakage Current (*11) (High level output voltage) VCC = 5 ~ 36[V], VOUT = 1.4[V] nA VOUT = 1.4[V] nA VOUT = 1.4[V] VOUT = open mA Full range - - 2.5 25℃ 6 16 - 25℃ - 150 400 VOUT = open, VCC = 36[V] mA VIN+ = 0[V], VIN = 1[V], VOL = 1.5[V] mV VIN+ = 0[V], VIN- = 1[V], IOL = 4[mA] Full range - - 700 25℃ - 0.1 - μA Full range - - 1 μA - 1.3 - - 0.4 - Ileak Response Time Tre 25℃ μs VIN+ = 1[V],VIN- = 0[V], VOH = 5[V] VIN+ = 1[V], VIN- = 0[V], VOH = 36[V] RL = 5.1[kΩ], VRL = 5[V] VIN=100[mVp-p],overdrive=5[mV] RL=5.1[kΩ], VRL=5[V], VIN=TTL Logic Swing, VREF=1.4[V] (*10) Absolute value (*11) BA2903S family: Full range -40[℃] ~ +105[℃], BA2903family: Full range -40[℃] ~ +125[℃] (*12) Under high temperatures, please consider the power dissipation when selecting the output current. When the output terminal is continuously shorted the output current reduces the internal temperature by flushing. www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 4/24 2011.08 - Rev.B BA10393F,BA10339F,BA10339FV,BA2903SF,BA2903SFV,BA2903SFVM,BA2903F,BA2903FV, BA2903FVM,BA2901SF,BA2901SFV,BA2901SKN,BA2901F,BA2901FV,BA2901KN,BA8391G Technical Note ○BA2901 family(Unless otherwise specified VCC=+5[V], VEE=0[V], Ta=25[℃]) Limits Parameter Symbol Temperature range 25℃ Input Offset Voltage (*13) (*14) BA2901S F/FV/FVM BA2901F/FV/FVM Min. Typ. Max. - 2 7 Vio Unit Condition VOUT=1.4[V] mV Full range - - 15 25℃ - 5 50 Full range - - 200 25℃ - 50 250 Full range - - 500 Vicm 25℃ 0 - VCC-1.5 V - Large Signal Voltage Gain AV 25℃ 88 100 - dB VCC=15[V], VOUT=1.4 ~ 11.4[V] RL=15[kΩ],VRL=15[V] Supply Current (*14) 25℃ - 0.8 2 ICC Input Offset Current (*13) (*14) Iio Input Bias Current (*13) (*14) Input Common-mode Voltage Range Ib Output Sink Current(*15) IOL Output Saturation Voltage (*14) (Low level output voltage) VOL Output Leakage Current (*14) (High level output voltage) VCC=5 ~ 36[V], VOUT=1.4[V] nA VOUT=1.4[V] nA VOUT=1.4[V] VOUT = open mA Full range - - 2.5 25℃ 6 16 - 25℃ - 150 400 VOUT = open, VCC = 36[V] mA VIN+ = 0[V], VIN = 1[V], VOL = 1.5[V] mV VIN+ = 0[V], VIN- = 1[V], IOL = 4[mA] Full range - - 700 25℃ - 0.1 - μA Full range - - 1 μA - 1.3 - - 0.4 - Ileak Response Time Tre 25℃ μs VIN+ = 1[V], VIN- = 0[V], VOH = 5[V] VIN+ = 1[V], VIN- = 0[V], VOH = 36[V] RL = 5.1[kΩ], VRL = 5[V] VIN=100[mVp-p],overdrive=5[mV] RL=5.1[kΩ], VRL=5[V], VIN =TTL Logic Swing, VREF = 1.4[V] (*13) Absolute value (*14) BA2901S family:Full range -40 ~ 105℃ ,BA2901 family:Full range -40 ~ +125℃ (*15) Under high temperatures, please consider the power dissipation when selecting the output current. When the output terminal is continuously shorted the output current reduces the internal temperature by flushing. www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 5/24 2011.08 - Rev.B BA10393F,BA10339F,BA10339FV,BA2903SF,BA2903SFV,BA2903SFVM,BA2903F,BA2903FV, BA2903FVM,BA2901SF,BA2901SFV,BA2901SKN,BA2901F,BA2901FV,BA2901KN,BA8391G Technical Note ●Reference Data BA8391 family BA83 91 ファ ミリ BA8391 family 800 BA8391 family BA8 39 1ファ ミリ 0.8 BA8391G 400 200 0.7 0.6 -40℃ 25℃ 0.5 SU PPLY CURR ENT [m A] SUPPLY CU RREN T [m A] POWER DISSIPATION[mW] 0.7 600 0.4 0.3 0.2 85℃ 0.1 0 0 0.2 50 -40℃ 0 20 30 2V 100 36V 50 2V 10 0 -50 -25 0 25 50 75 80 60 40 85℃ 0 5 10 15 20 25 30 35 75 40 SUPPLY VOLTAGE[V] Fig.10 Fig.10 Input Bias Current - Supply Voltage 入力バイアス電流-電源電圧特性 75 100 BA8 39 1フfamily ァ ミリ BA8391 1.6 1.4 25℃ 1.2 85℃ 1.0 0.8 0.6 0.4 -40℃ 0 100 -40℃ 2 0 85℃ 25℃ 4 6 8 10 12 14 16 18 20 Fig.6 Fig.6 Low Level Output Voltage Low レベル出力電圧-出力シンク電流特性 - Output Sink Current (VCC=5[V]) (VCC=5[V]) 4 -2 2 OUTPUT SINK CUR RENT[m A] BA8391 BA8 39 1フfamily ァ ミリ -4 -6 BA8 39 1ファ ミリ BA8391 family 8 -8 6 4 2V 2 0 5V -2 36V -4 -6 -8 0 10 20 30 40 -50 140 120 36V 100 80 5V 60 40 2V 20 0 -50 0 25 50 75 100 Fig.9 Fig.9 Input 入力オフセット電圧-温度特性 Offset Voltage - Ambient Temperature BA8391 BA8 39 1フfamily ァ ミリ 160 -25 AMBIENT TEMPERATURE[℃] Fig.8 Fig.8 Input Offset Voltage - Supply Voltage 入力オフセット電圧-電源電圧特性 INPU T BIAS CUR RENT [nA] 25℃ 50 回路電流 - 温度特性 2.0 SUPPLY VOLTAGE[V] 120 0 50 6 100 140 20 25 (IOL=4[mA]) (IOL=4[mA]) BA8391 BA8 39 1フ ァfamily ミリ -40℃ 0 8 (VOUT=1.5[V]) (VOUT=1.5[V]) 100 -25 Fig.5 Fig.5 Output Saturation Voltage 出力飽和電圧-温度特性 - Ambient Temperature AMBIENT TEMPERATURE [℃] 160 5V AMBIENT TEMPERATURE [℃] Fig.7 Fig.7 Output Sink Current - Ambient Temperature 出力シンク電流-温度特性 25 0.0 -50 INPUT OFF SET VOLT AGE[m V] 20 0 Fig.3 Fig.3 Supply Current - Ambient Temperature 0 40 36V -25 0.2 BA8391 family BA8 39 1フ ァ ミリ 5V -50 AMBIENT TEMPERATURE [℃] 150 Fig.4 Fig.4 Output Saturation Voltage 出力飽和電圧-電源電圧特性 - Supply Voltage (IOL=4[mA]) (IOL=4[mA]) 30 40 1.8 SUPPLY VOLTAGE[V] 40 2V 0.1 BA8 39 1フfamily ァ ミリ BA8391 200 M AXIM U M OUTPU T VOLTAGE [m V] M AXIM UM OUTPUT VOLTAGE [m V] 85℃ 100 10 30 回路電流 - 電源電圧特性 150 0 20 Fig.2 Fig.2 Supply Current - Supply Voltage BA83 91 ファ ミリ BA8391 family 25℃ 10 SUPPLY VOLTAGE [V] ディレーティングカーブ 200 OUTPUT SINK C URRENT[m A] 0.3 0.0 125 Fig.1 Fig.1 Derating Curve 5V 0.4 OU TPUT VOLT AGE[V] 75 85 100 36V 0.5 INPUT OFFSET VOLTAGE[m V] 50 BA8391 family BA83 91 ファ ミリ 50 INPUT OF FSET CURRENT[nA] 25 AMBIENT TEMPERATURE[℃] INPUT BIAS CU RREN T[nA] 0.6 0.0 0 BA8391 BA83 91 family ファ ミリ 0.8 40 30 20 -40℃ 10 25℃ 0 -10 85℃ -20 -30 -40 -50 -25 0 25 50 75 100 AMBIENT TEMPERATURE[℃] Fig.11 Input Bias Current - Ambient Temperature 入力バイアス電流-温度特性 0 10 20 30 40 SUPPLY VOLTAGE[V] Fig.12 Fig.12 Input Offset Current - Supply Voltage 入力オフセット電流-電源電圧特性 (*)The data above is ability value of sample, it is not guaranteed. BA8391G:-40[℃]~+85[℃] www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 6/24 2011.08 - Rev.B BA10393F,BA10339F,BA10339FV,BA2903SF,BA2903SFV,BA2903SFVM,BA2903F,BA2903FV, BA2903FVM,BA2901SF,BA2901SFV,BA2901SKN,BA2901F,BA2901FV,BA2901KN,BA8391G Technical Note ●Reference Data BA8391 family BA8391ファ ミリ BA8391 family 30 20 2V 0 -10 5V -20 36V -30 -40 110 25℃ 100 80 70 60 0 25 50 75 0 100 85℃ 120 100 25℃ 80 -40℃ 60 40 0 10 20 30 125 100 2V 75 50 25 40 0 -50 BA8391 family BA8391ファ ミリ 160 140 120 100 80 50 75 Fig.19 Fig.19 Power Supply Rejection Ratio 電源電圧除去比-温度特性 - Ambient Temperature RESPONSE TIME ( HIGH TO LOW)[μs]. 4 3 85℃ 25℃ -40℃ 1 0 0 20 40 60 50 75 80 70 -25 80 100 OUTPUT DRIVE VOLTAGE[mV] 25 50 75 100 Fig.15 Fig.15 Large Signal Voltage Gain 大振幅電圧利得-温度特性 - Ambient Temperature BA8391ファ ミリ BA8391 family 6 4 25℃ -40℃ 2 85℃ 0 -2 -4 -1 0 BA8391 family BA8391ファ ミリ 85℃ -40℃ 25℃ 1 -80 -60 -40 -20 0 OUTPUT DRIVE VOLTAGE[mV] Fig.20 Fig.20 Response Time (Low to High) L→H応答時間-オーバードライブ電圧特性 - Over Drive Voltage (VCC=5[V],VRL=5[V],RL=5.1[kΩ]) (VCC=5[V],VRL=5[V],RL=5.1[kΩ]) BA8391 family BA8391ファ ミリ 5 1 2 3 4 5 INPUT VOLTAGE[V] 2 0 -100 0 AMBIENT TEMPERATURE[℃] 100 3 RESPONSE TIME ( HIGH TO LOW)[μs] BA8391 family BA8391ファ ミリ 2 25 4 100 AMBIENT TEMPERATURE[℃] 5 0 5 RESPONSE TIME (LOW TO HIGH)[μs] POWER SUPPLY REJECTION RATIO[dB] 180 25 2V 90 -6 -25 Fig.17 Fig.17 Common Mode Rejection Ratio 同相信号除去比-温度特性 - Ambient Temperature - Supply Voltage 0 100 AMBIENT TEMPERATURE[℃] Fig.16 Fig.16 Common Mode Rejection Ratio 同相信号除去比-電源電圧特性 -25 36V 5V 36V 110 60 -50 40 BA8391ファ ミリ BA8391 family 150 SUPPLY VOLTAGE[V] 200 30 5V 120 Fig.14 Fig.14 Large Signal Voltage Gain 大振幅電圧利得-電源電圧特性 - Supply Voltage COMMON MODE REJECTION RATIO[dB] 140 20 130 SUPPLY VOLTAGE[V] BA8391ファ ミリ BA8391 family 160 10 INPUT OFFSET VOLTAGE[mV] -25 Fig.13 Fig.13 Input Offset Current - Ambient Temperature 入力オフセット電流-温度特性 60 -50 -40℃ 90 AMBIENT TEMPERATURE[℃] COMMON MODE REJECTION RATIO[dB] 85℃ 120 Fig.18 Fig.18 Input Offset Voltage - Input Voltage 入力オフセット電圧-同相入力電圧範囲 (VCC=5V) (VCC=5[V]) BA8391 family BA8391ファ ミリ 5 RESPONSE TIME (LOW TO HIGH)[μs] -50 -50 130 BA8391 family BA8391ファ ミリ 140 LARGE SIGNAL VOLTAGE GAIN[dB] 40 10 BA8391 family BA8391ファ ミリ 140 LARGE SINGAL VOLTAGE GAIN[dB] INPUT OFFSET CURRENT[nA] 50 4 3 100m V overdrive 20m V overdrive 2 5mV overdrive 1 0 -50 -25 0 25 50 75 100 AMBIENT TEMPERATURE[℃] Fig.21 Fig.21 Response Time (Low to High) L→H応答時間-温度特性 - Ambient Temperature (VCC=5[V],VRL=5[V],RL=5.1[kΩ]) (VCC=5[V],VRL=5[V],RL=5.1[kΩ]) 4 3 5m V overdrive 20m V overdrive 2 100mV overdrive 1 0 -50 -25 0 25 50 75 100 AMBIENT TEMPERATURE[℃] Fig.22 Fig.23 Fig.23 Fig.22 Response Time (High to Low) H→L応答時間-オーバードライブ電圧特性 Response Time (High to Low) H→L応答時間-温度特性 - Ambient Temperature - Over Drive Voltage (VCC=5[V],VRL=5[V],RL=5.1[kΩ]) (VCC=5[V],VRL=5[V],RL=5.1[kΩ]) (VCC=5[V],VRL=5[V],RL=5.1[kΩ]) (VCC=5[V],VRL=5[V],RL=5.1[kΩ]) (*)The data above is ability value of sample, it is not guaranteed. BA8391G:-40[℃]~+85[℃] www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 7/24 2011.08 - Rev.B BA10393F,BA10339F,BA10339FV,BA2903SF,BA2903SFV,BA2903SFVM,BA2903F,BA2903FV, BA2903FVM,BA2901SF,BA2901SFV,BA2901SKN,BA2901F,BA2901FV,BA2901KN,BA8391G Technical Note ●Reference Data BA10393 family BA10393 family BA10393 family 1 400 200 0 25℃ 0.6 0.4 85℃ 0.2 25 50 75 85 100 AMBIENT TEMPERATURE [℃] . 125 0 Fig.24 Derating Curve 200 -40℃ 100 0 0 10 20 30 SUPPLY VOLTAGE [V] 40 400 2V 300 5V 200 36V 100 0 -50 0 25 50 75 5V 20 2V 0 25 50 1.4 25℃ 1.2 85℃ 1.0 0.8 0.6 0.4 -40℃ 0.2 0 75 2 4 6 (VCC=5[V]) 4 -40℃ 25℃ 0 -2 85℃ -4 -6 100 BA10393 family 8 6 4 2V 2 5V 0 -2 36V -4 -6 -8 0 AMBIENT TEMPERATURE [℃] 10 20 30 40 -50 -25 0 25 50 75 100 AMBIENT TEMPERATURE [℃] SUPPLY VOLTAGE [V] Fig.30 Output Sink Current - Ambient Temperature 10 12 14 16 18 20 Fig.29 Low Level Output Voltage - Output Sink Current 6 2 8 OUTPUT SINK CURRENT [mA] -8 0 1.6 100 BA10393 family 8 INPUT OFFSET VOLTAGE [mV] 36V -25 1.8 (IOL=4[mA]) 30 -50 BA10393 family 2.0 Fig.28 Output Saturation Voltage - Ambient Temperature BA10393 family 100 0.0 -25 (IOL=4[mA]) 10 -25 0 25 50 75 AMBIENT TEMPERATURE [℃] Fig.26 Supply Current - Ambient Temperature AMBIENT TEMPERATURE [℃] Fig.27 Output Saturation Voltage - Supply Voltage 40 2V 0.2 -50 LOW LEVEL OUTPUT VOLTAGE [V] 25℃ 300 36V 0.4 40 BA10393 family 500 OUTPUT SATURATION VOLTAGE [mV] 85℃ 400 10 20 30 SUPPLY VOLTAGE [V] Fig.25 Supply Current - Supply Voltage BA10393 family 500 5V 0.6 0 0 0 OUTPUT SINK CURRENT [mA] SUPPLY CURRENT [mA] SUPPLY CURRENT [mA] BA10393F 600 OUTPUT SATURATION VOLTAGE [mV] 0.8 0.8 INPUT OFFSET VOLTAGE [mV] POWER DISSIPATION [mW] . 800 BA10393 family 1 -40℃ . 1000 Fig.31 Input Offset Voltage - Supply Voltage Fig.32 Input Offset Voltage - Ambient Temperature (VOUT=1.5[V]) BA10393 family . 160 100 -40℃ 25℃ 80 60 40 85℃ 20 INPUT OFFSET CURRENT [nA] INPUT BIAS CURRENT [nA] 120 120 36V 100 80 5V 60 40 2V 20 0 10 20 30 40 SUPPLY VOLTAGE [V] Fig.33 Input Bias Current - Supply Voltage 30 20 -40℃ 10 0 25℃ -10 85℃ -20 -30 -40 0 0 BA10393 family 50 40 140 140 INPUT BIAS CURRENT [nA] BA10393 family 160 -50 -50 -25 0 25 50 75 AMBIENT TEMPERATURE [℃] 100 Fig.34 Input Bias Current - Ambient Temperature 0 10 20 30 SUPPLY VOLTAGE [V] 40 Fig.35 Input Offset Current - Supply Voltage (*)The data above is ability value of sample, it is not guaranteed. BA10393F:-40[℃]~+85[℃] www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 8/24 2011.08 - Rev.B BA10393F,BA10339F,BA10339FV,BA2903SF,BA2903SFV,BA2903SFVM,BA2903F,BA2903FV, BA2903FVM,BA2901SF,BA2901SFV,BA2901SKN,BA2901F,BA2901FV,BA2901KN,BA8391G Technical Note 36V 30 20 10 5V 0 -10 2V -20 -30 -40 130 -50 BA10393 family . 140 25℃ LARGE SIGNAL VOLTAGE GAIN [dB] INPUT OFFSET CURRENT [nA] 40 . BA10393 family 50 LARGE SIGNAL VOLTAGE GAIN [dB] ●Reference Data BA10393 family 120 110 100 85℃ -40℃ 90 80 70 60 -50 -25 0 25 50 75 AMBIENT TEMPERATURE [℃] 100 BA10393 family 140 130 36V 120 110 100 2V 90 5V 80 70 60 0 10 20 30 SUPPLY VOLTAGE [V] -50 Fig.37 Large Signal Voltage Gain - Supply Voltage -25 0 25 50 75 AMBIENT TEMPERATURE [°C] 100 Fig.38 Large Signal Voltage Gain - Ambient Temperature . Fig.36 Input Offset Current - Ambient Temperature 40 140 120 -40℃ 25℃ 100 80 85℃ 60 40 0 10 20 30 SUPPLY VOLTAGE [V] 130 120 90 80 2V 70 60 -50 3 5mV overdrive 2 20mV overdrive 1 100mV overdrive 0 -50 -25 0 25 50 75 AMBIENT TEMPERATURE [°C] 100 -25 0 25 50 75 AMBIENT TEMPERATURE [°C] 100 Fig.40 Common Mode Rejection Ratio - Ambient Temperature BA10393 family 140 130 120 110 100 90 80 70 60 -50 -25 0 25 50 75 AMBIENT TEMPERATURE [°C] 100 Fig.41 Power Supply Rejection Ratio - Ambient Temperature . BA10393 family 5 RESPONSE TIME (HIGH to LOW) [μs] . . RESPONSE TIME (LOW to HIGH) [μs] 4 5V 100 40 BA10393 family 36V 110 Fig.39 Common Mode Rejection Ratio - Supply Voltage 5 BA10393 family 140 POWER SUPPLY REJECTION RATIO [dB] COMMON MODE REJECTION RATIO[dB] . POWER SUPPLY REJECTION RATIO [dB] BA10393 family 160 4 3 5mV overdrive 2 20mV overdrive 100mV overdrive 1 0 -50 -25 0 25 50 75 AMBIENT TEMPERATURE [°C] 100 Fig.42 Response Time (Low to High) - Ambient Temperature Fig.43 Response Time (High to Low) -Ambient Temperature (VCC=5[V],VRL=5[V],RL=5.1[kΩ]) (VCC=5[V],VRL=5[V],RL=5.1[kΩ]) (*)The data above is ability value of sample, it is not guaranteed. BA10393F:-40[℃]~+85[℃] www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 9/24 2011.08 - Rev.B BA10393F,BA10339F,BA10339FV,BA2903SF,BA2903SFV,BA2903SFVM,BA2903F,BA2903FV, BA2903FVM,BA2901SF,BA2901SFV,BA2901SKN,BA2901F,BA2901FV,BA2901KN,BA8391G Technical Note ●Reference Data BA10339 family BA10339 family 1000 BA10339 family 1 BA10339 family 1 SUPPLY CURRENT [mA] BA10339FV 600 400 BA10339F 200 0 0.8 25℃ 0.6 0.4 85℃ 0.2 25 50 75 100 AMBIENT TEMPERATURE [℃] . 125 0 BA10339 family 300 25℃ 200 -40℃ 0 10 20 30 SUPPLY VOLTAGE [V] 2V 200 5V 36V 100 0 -50 40 Fig.47 Output Saturation Voltage - Supply Voltage -25 0 25 50 75 AMBIENT TEMPERATURE [℃] 36V 5V 10 3V -25 0 25 BA10339 family 1.6 1.4 1.2 1.0 85℃ 0.8 25℃ 0.6 0.4 -40℃ 0.2 0 2 4 6 (VCC=5[V]) 4 2 -40℃ 25℃ -2 -4 85℃ -6 50 75 BA10339 family 8 6 4 2 0 36V 5V -2 -4 3V -6 -8 0 100 10 20 30 -50 40 SUPPLY VOLTAGE [V] AMBIENT TEMPERATURE [℃] -25 0 25 50 75 100 AMBIENT TEMPERATURE [℃] Fig.51 Input Offset Voltage - Supply Voltage Fig.50 Output Sink Current - Ambient Temperature 10 12 14 16 18 20 Fig.49 Low Level Output Voltage - Output Sink Current 6 0 8 OUTPUT SINK CURRENT [mA] -8 0 100 1.8 100 BA10339 family 8 INPUT OFFSET VOLTAGE [mV] 30 -50 -25 0 25 50 75 AMBIENT TEMPERATURE [℃] (IOL=4[mA]) BA10339 family 20 2V 0.2 Fig.48 Output Saturation Voltage - Ambient Temperature (IOL=4[mA]) 40 5V 0.4 0.0 INPUT OFFSET VOLTAGE [mV] 0 400 300 0.6 2.0 LOW LEVEL OUTPUT VOLTAGE [V] 85℃ 36V Fig.46 Supply Current - Ambient Temperature BA10339 family 500 OUTPUT SATURATION VOLTAGE [mV] OUTPUT SATURATION VOLTAGE [mV] 400 100 40 Fig.45 Supply Current - Supply Voltage Fig.44 Derating Curve 500 10 20 30 SUPPLY VOLTAGE [V] 0.8 0 -50 0 0 OUTPUT SINK CURRENT [mA] SUPPLY CURRENT [mA] . POWER DISSIPATION [mW] . -40℃ 800 Fig.52 Input Offset Voltage - Ambient Temperature (VOUT=1.5[V]) BA10339 family BA10339 family 50 BA10339 family 50 . 50 25℃ -40℃ 20 10 85℃ INPUT OFFSET CURRENT [nA] 30 INPUT BIAS CURRENT [nA] INPUT BIAS CURRENT [nA] 40 40 40 36V 30 20 5V 10 0 0 10 20 30 40 SUPPLY VOLTAGE [V] Fig.53 Input Bias Current - Supply Voltage 20 85℃ 10 0 -10 -40℃ -20 25℃ -30 -40 3V 0 30 -50 -50 -25 0 25 50 75 AMBIENT TEMPERAUTRE [℃] 100 Fig.54 Input Bias Current - Ambient Temperature 0 10 20 30 SUPPLY VOLTAGE [V] 40 Fig.55 Input Offset Current - Supply Voltage (*)The data above is ability value of sample, it is not guaranteed. BA10339F/FV:-40[℃]~+85[℃] www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 10/24 2011.08 - Rev.B BA10393F,BA10339F,BA10339FV,BA2903SF,BA2903SFV,BA2903SFVM,BA2903F,BA2903FV, BA2903FVM,BA2901SF,BA2901SFV,BA2901SKN,BA2901F,BA2901FV,BA2901KN,BA8391G Technical Note ●Reference Data BA10339 family 30 36V LARGE SIGNAL VOLTAGE GAIN [dB] 5V 20 10 0 -10 3V -20 -30 -40 130 120 85℃ 110 100 -50 -40℃ 90 80 70 -25 0 25 50 75 100 0 10 20 30 SUPPLY VOLTAGE [V] AMBIENT TEMPERATURE [℃] 140 120 -40℃ 25℃ 100 80 85℃ 60 . 125 36V 5V 75 3V 50 25 0 10 20 30 40 -50 SUPPLY VOLTAGE [V] Fig.59 Common Mode Rejection Ratio - Supply Voltage 3 5mV overdrive 2 20mV overdrive 1 100mV overdrive 5V 90 3V 80 70 -50 -25 0 25 50 75 AMBIENT TEMPERATURE [°C] 100 100 BA10339 family 140 130 120 110 100 90 80 70 60 -50 -25 0 25 50 75 AMBIENT TEMPERATURE [°C] 100 Fig.61 Power Supply Rejection Ratio - Ambient Temperature BA10339 family 5 RESPONSE TIME (HIGH to LOW) [μs] 4 -25 0 25 50 75 AMBIENT TEMPERATURE [°C] Fig.60 Common Mode Rejection Ratio - Ambient Temperature BA10339 family 5 100 Fig.58 Large Signal Voltage Gain - Ambient Temperature 100 40 0 36V 110 40 BA10339 family 150 LARGE SIGNAL VOLTAGE GAIN [dB] COMMON MODE REJECTION RATIO [dB] BA10339 family 120 Fig.57 Large Signal Voltage Gain - Supply Voltage Fig.56 Input Offset Current - Ambient Temperature 160 130 60 60 -50 RESPONSE TIME (LOW to HIGH) [μs] 25℃ BA10339 family 140 POWER SUPPLY REJECTION RATIO [dB] INPUT OFFSET CURRENT [nA] 40 BA10339 family 140 LARGE SIGNAL VOLTAGE GAIN [dB] BA10339 family 50 4 3 5mV overdrive 2 20mV overdrive 100mV overdrive 1 0 0 -50 -25 0 25 50 75 AMBIENT TEMPERATURE [°C] 100 Fig.62 Response Time (Low to High) - Ambient Temperature (VCC=5[V],VRL=5[V],RL=5.1[kΩ]) -50 -25 0 25 50 75 AMBIENT TEMPERATURE [°C] 100 Fig.63 Response Time (High to Low) - Ambient Temperature (VCC=5[V],VRL=5[V],RL=5.1[kΩ]) (*)The data above is ability value of sample, it is not guaranteed. BA10339F/FV:-40[℃]~+85[℃] www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 11/24 2011.08 - Rev.B BA10393F,BA10339F,BA10339FV,BA2903SF,BA2903SFV,BA2903SFVM,BA2903F,BA2903FV, BA2903FVM,BA2901SF,BA2901SFV,BA2901SKN,BA2901F,BA2901FV,BA2901KN,BA8391G Technical Note ●Reference Data BA2903 family BA2903 family 1000 BA2903 family 1.6 1.4 600 BA2903SF BA2903FVM BA2903SFV -40℃ 0.8 25℃ 0.6 0.4 0.2 0 0.0 105 10 20 30 105℃ 100 50 25℃ -40℃ 0 0 10 20 30 150 2V 100 5V 50 36V BA2903 family 0 25 50 75 -25 INPUT OFFSET VOLTAGE [mV] OUTPUT SINK CURRENT [mA] 0 25 50 75 100 125 4 -40℃ 2 0 25℃ -2 105℃ 125℃ -4 -6 25℃ 80 60 40 105℃ 10 20 30 20 25 30 SUPPLY VOLTAGE [V] Fig.73 Input Bias Current - Supply Voltage 10 12 14 16 18 20 4 2V 2 0 5V -2 36V -4 -6 -50 -25 0 25 50 75 100 125 150 AMBIENT TEMPERATURE [℃] Fig.72 Input Offset Voltage - Ambient Temperature BA2903 family 50 40 140 120 100 36V 80 60 40 5V 20 35 8 6 40 30 20 -40℃ 10 25℃ 0 -10 125℃ 105℃ -20 -30 -40 2V 0 15 6 BA2903 family BA2903 family 160 125℃ 0 4 8 INPUT OFFSET CURRENT[nA] 120 10 -40℃ 2 -8 0 INPUT BIAS CURRENT [nA] INPUT BIAS CURRENT [nA] 140 5 0.4 (VCC=5[V]) BA2903 family (VOUT=1.5[V]) 0 105℃ 0.6 (IOL=4[mA]) Fig.71 Input Offset Voltage - Supply Voltage 20 0.8 Fig.69 Low Level Output Voltage - Output Sink Current 6 100 125 150 BA2903 family 25℃ 125℃ 1 Fig.68 Output Saturation Voltage - Ambient Temperature Fig.70 Output Sink Current - Ambient Temperature -40℃ 1.2 OUTPUT SINK CURRENT [mA] SUPPLY VOLTAGE [V] 100 1.4 150 AMBIENT TEMPERATURE [℃] 160 1.6 0 -8 -25 100 125 150 0 8 0 -50 75 0.2 -50 40 2V 50 BA2903 family 0 (IOL=4[mA]) 20 25 Fig.66 Supply Current - Ambient Temperature SUPPLY VOLTAGE [V] 36V 0 1.8 40 5V -25 AMBIENT TEMPERATURE [℃] 2 Fig.67 Output Saturation Voltage - Supply Voltage 10 2V -50 200 SUPPLY VOLTAGE [V] 30 0.4 BA2903 family MAXIMUM OUTPUT VOLTAGE [mV] MAXIMUM OUTPUT VOLTAGE [mV] 125℃ 5V 0.6 40 Fig.65 Supply Current - Supply Voltage BA2903 family 150 36V 0.8 SUPPLY VOLTAGE [V] Fig.64 Derating Curve 200 1.0 0.0 0 25 50 75 100 125 150 AMBIENTTEMPERATURE TEMPERTURE [℃] [℃] . AMBIENT 1.2 0.2 125℃ 105℃ BA2903SFVM 0 1.0 OUTPUT VOLTAGE [V] 200 1.2 INPUT OFFSET VOLTAGE [mV] 400 SUPPLY CURRENT [mA] BA2903FV SUPPLY CURRENT [mA] POWER DISSIPATION [mW] POWER DISSIPATION [mV] 1.4 BA2903F 800 BA2903 family 1.6 -50 -50 -25 0 25 50 75 100 125 150 AMBIENT TEMPERATURE [℃] Fig.74 Input Bias Current - Ambient Temperature 0 10 20 30 40 SUPPLY VOLTAGE [V] Fig.75 Input Offset Current - Supply Voltage (*)The data above is ability value of sample, it is not guaranteed. BA2903S:-40[℃]~+105[℃] BA2903:-40[℃]~+125[℃] www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 12/24 2011.08 - Rev.B BA10393F,BA10339F,BA10339FV,BA2903SF,BA2903SFV,BA2903SFVM,BA2903F,BA2903FV, BA2903FVM,BA2901SF,BA2901SFV,BA2901SKN,BA2901F,BA2901FV,BA2901KN,BA8391G Technical Note ●Reference Data BA2903 family 30 2V 10 0 -10 36V 5V -20 -30 -40 -50 -50 -25 0 25 50 75 120 110 100 25℃ 90 70 60 100 125 150 0 10 140 120 125℃ 105℃ 100 80 25℃ -40℃ 60 40 0 10 20 30 40 COMMON MODE REJECTION RATIO [dB] COMMON MODE REJECTION RATIO [dB] Fig.76 Input Offset Current - Ambient Temperature BA2903 family RESPONSE TIME (LOW TO HIGH)[μs] 140 120 100 80 60 RESPONSE TIME (HIGH TO LOW)[μs] 50 75 100 80 70 60 -50 40 5V 15V 90 -25 0 25 50 75 100 125 150 AMBIENT TEMPERATURE [℃] Fig.77 Large Signal Voltage Gain - Supply Voltage Fig.78 Large Signal Voltage Gain - Ambient Temperature BA2903 family 100 75 5V 2V 50 BA2903 family 6 36V 25 0 105℃ 25℃ 4 -40℃ 2 125℃ 0 -2 -4 -6 -50 -25 0 25 50 75 100 125 150 -1 0 4 3 2 125℃ 105℃ -40℃ 25℃ 1 0 -80 -60 -40 -20 1 2 3 4 5 INPUT VOLTAGE [V] Fig.81 Input Offset Voltage - Input Voltage (VCC=5V) BA2903 family 5 -100 100 125 150 0 BA2903 family 5 4 3 100mV overdrive 5mV overdrive 20mV overdrive 2 1 0 -50 -25 0 25 50 75 100 125 150 AMBIENT TEMPERATURE [℃] OVER DRIVE VOLTAGE [V] AMBIENT TEMPERATURE [℃] Fig.82 Power Supply Rejection Ratio - Ambient Temperature Fig.83 Response Time (Low to High) - Over Drive Voltage Fig.84 Response Time (Low to High) - Ambient Temperature (VCC=5[V],VRL=5[V],RL=5.1[kΩ]) (VCC=5[V],VRL=5[V],RL=5.1[kΩ]) BA2903 family 5 RESPONSE TIME (HIGH TO LOW)[μs] POWER SUPPLY REJECTION RATIO [dB] 160 25 110 Fig.80 Common Mode Rejection Ratio - Ambient Temperature 180 0 36V 120 AMBIENT TEMPERATURE [℃] BA2903 family -25 30 130 SUPPLY VOLTAGE [V] 125 Fig.79 Common Mode Rejection Ratio - Supply Voltage -50 20 150 SUPPLY VOLTAGE [V] 200 -40℃ 80 AMBIENT TEMPERATURE [℃] 160 105℃ 125℃ RRESPONSE TIME (LOW TO HIGH)[μs] 20 130 BA2903 family 140 INPUT OFFSET VOLTAGE [mV] LARGE SINGAL VOLTAGE GAIN [dB] INPUT OFFSET CURRENT [nA] 40 BA2903 family 140 LARGE SINGAL VOLTAGE GAIN [dB] BA2903 family 50 4 3 125℃ 105℃ 2 25℃ -40℃ 1 0 0 20 40 60 80 OVER DRIVE VOLTAGE [V] Fig.85 Response Time (High to Low) - Over Drive Voltage (VCC=5[V],VRL=5[V],RL=5.1[kΩ]) 100 BA2903 family 5 4 100mV overdrive 3 20mV overdrive 5mV overdrive 2 1 0 -50 -25 0 25 50 75 100 125 150 AMBIENT TEMPERATURE [℃] Fig.86 Response Time (High to Low) - Ambient Temperature (VCC=5[V],VRL=5[V],RL=5.1[kΩ]) (*)The data above is ability value of sample, it is not guaranteed. BA2903S:-40[℃]~+105[℃] BA2903:-40[℃]~+125[℃] www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 13/24 2011.08 - Rev.B BA10393F,BA10339F,BA10339FV,BA2903SF,BA2903SFV,BA2903SFVM,BA2903F,BA2903FV, BA2903FVM,BA2901SF,BA2901SFV,BA2901SKN,BA2901F,BA2901FV,BA2901KN,BA8391G Technical Note ●Reference Data BA2901 family BA2901 family 1000 BA2901F BA2901SFV 400 200 BA2901SKN 25 50 1.4 1.2 1.0 0.8 0.6 125℃ 0.4 75 100 125 150 0 10 AMBIENT TEMPERATURE [℃] 105℃ 100 50 -40℃ 0 10 20 0.4 2V -50 30 -25 0 25 50 75 100 125 150 AMBIENT TEMPERATURE [℃] Fig.89 Supply Current - Ambient Temperature BA2901 family BA2901 family 2 1.8 150 2V 100 5V 50 36V 1.6 1.4 25℃ 125℃ 1.2 1 0.8 105℃ 0.6 0.4 0.2 -40℃ 0 40 -50 -25 SUPPLY VOLTAGE [V] 0 25 50 75 100 125 0 150 2 4 6 8 10 12 14 16 Fig.90 Output Saturation Voltage - Supply Voltage Fig.91 Output Saturation Voltage - Ambient Temperature Fig.92 Low Level Output Voltage - Output Sink Current (IOL=4[mA]) (IOL=4[mA]) (VCC=5[V]) 5V 36V 20 2V 10 0 6 4 -40℃ 2 0 25℃ -2 105℃ 125℃ -4 -6 0 25 50 75 100 125 150 0 10 4 2V 2 0 5V -2 36V -4 -6 20 30 -50 40 -25 0 25 50 75 100 125 150 SUPPLY VOLTAGE [V] AMBIENT TEMPERATURE [℃] Fig.94 Input Offset Voltage - Supply Voltage Fig.95 Input Offset Voltage - Ambient Temperature AMBIENT TEMPERATURE [℃] Fig.93 Output Sink Current - Ambient Temperature 6 -8 -8 -25 20 BA2901 family 8 INPUT OFFSET VOLTAGE [mV] 30 BA2901 family 8 INPUT OFFSET VOLTAGE [mV] 40 18 OUTPUT SINK CURRENT [mA] SUPPLY VOLTAGE [V] BA2901 family -50 5V 0.6 40 0 0 OUTPUT SINK CURRENT [mA] 30 200 MAXIMUM OUTPUT VOLTAGE [mV] MAXIMUM OUTPUT VOLTAGE [mV] 125℃ 25℃ 20 Fig.88 Supply Current - Supply Voltage BA2901 family 150 36V 0.8 SUPPLY VOLTAGE [V] Fig.87 Derating Curve 200 1.0 0.0 0.0 105 1.2 0.2 105℃ 0.2 BA2901SF 0 0 -40℃ OUTPUT VOLTAGE [V] 600 1.4 25℃ 1.6 SUPPLY CURRENT [mA] SUPPLY CURRENT [mA] POWER DISSIPATION [mW] BA2901KN BA2901 family 1.6 1.8 BA2901FV 800 BA2901 family 2.0 (VOUT=1.5[V]) BA2901 family 120 25℃ -40℃ 100 80 60 40 20 105℃ 0 5 10 15 20 120 100 36V 80 60 40 5V 20 2V 125℃ 0 140 0 25 30 35 SUPPLY VOLTAGE [V] Fig.96 Input Bias Current - Supply Voltage BA2901 family 50 INPUT OFFSET CURRENT[nA] 140 BA2901 family 160 INPUT BIAS CURRENT [nA] INPUT BIAS CURRENT [nA] 160 40 30 20 -40℃ 10 25℃ 0 -10 105℃ -20 125℃ -30 -40 -50 -50 -25 0 25 50 75 100 125 150 AMBIENT TEMPERATURE [℃] Fig.97 Input Bias Current - Ambient Temperature 0 10 20 30 40 SUPPLY VOLTAGE [V] Fig.98 Input Offset Current - Supply Voltage (*)The data above is ability value of sample, it is not guaranteed. BA2901:-40[℃]~+125[℃] BA2901S:-40[℃]~+105[℃] www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 14/24 2011.08 - Rev.B BA10393F,BA10339F,BA10339FV,BA2903SF,BA2903SFV,BA2903SFVM,BA2903F,BA2903FV, BA2903FVM,BA2901SF,BA2901SFV,BA2901SKN,BA2901F,BA2901FV,BA2901KN,BA8391G Technical Note ●Reference Data BA2901 family BA2901 family 2V 10 0 -10 5V -20 36V -30 -40 -50 -50 -25 0 25 50 75 110 100 25℃ 90 70 60 10 Fig.99 Input Offset Current - Ambient Temperature 125℃ 105℃ 100 80 25℃ -40℃ 60 40 0 10 20 30 40 COMMON MODE REJECTION RATIO [dB] COMMON MODE REJECTION RATIO [dB] 120 20 30 RESPONSE TIME (LOW TO HIGH)[μs] POWER SUPPLY REJECTION RATIO [dB] 140 120 100 80 60 -50 -25 0 25 50 75 BA2901 family 125 36V 100 75 5V 2V 50 25 -25 0 25 50 75 25℃ -40℃ 1 0 0 20 40 60 80 OVER DRIVE VOLTAGE [V] 100 50 75 100 125 150 BA2901 family 105℃ -40℃ 2 125℃ 0 -2 -4 -1 0 1 2 3 4 5 Fig.103 Common Mode Rejection Ratio - Ambient Temperature Fig.104 Input Offset Voltage - Input Voltage (VCC=5V) BA2901 family BA2901 family 4 3 2 125℃ 105℃ 25℃ -40℃ 1 0 -80 -60 -40 -20 0 5 4 3 5mV overdrive 100mV overdrive 20mV overdrive 2 1 0 -50 -25 0 25 50 75 100 125 150 AMBIENT TEMPERATURE [℃] Fig.107 Response Time (Low to High) - Ambient Temperature (VCC=5[V],VRL=5[V],RL=5.1[kΩ]) BA2901 family RESPONSE TIME (HIGH TO LOW)[μs] RESPONSE TIME (HIGH TO LOW)[μs] 105℃ 25 INPUT VOLTAGE [V] (VCC=5[V],VRL=5[V],RL=5.1[kΩ]) BA2901 family 2 0 4 100 125 150 Fig.106 Response Time (Low to High) - Over Drive Voltage 125℃ -25 AMBIENT TEMPERATURE [℃] 5 Fig.105 Power Supply Rejection Ratio - Ambient Temperature 3 60 -6 -50 OVER DRIVE VOLTAGE [V] 4 70 6 0 AMBIENT TEMPERATURE [℃] 5 80 -50 40 5V 15V 90 Fig.101 Large Signal Voltage Gain - Ambient Temperature -100 100 125 150 100 Fig.100 Large Signal Voltage Gain - Supply Voltage BA2901 family 160 110 25℃ Fig.102 Common Mode Rejection Ratio - Supply Voltage 180 36V 120 AMBIENT TEMPERATURE [℃] 150 SUPPLY VOLTAGE [V] 200 130 SUPPLY VOLTAGE [V] AMBIENT TEMPERATURE [℃] 140 -40℃ 80 0 BA2901 family 105℃ 125℃ 120 100 125 150 160 LARGE SINGAL VOLTAGE GAIN [dB] 20 130 INPUT OFFSET VOLTAGE [mV] 30 140 RRESPONSE TIME (LOW TO HIGH)[μs] 40 BA2901 family BA2901 family 140 LARGE SINGAL VOLTAGE GAIN [dB] INPUT OFFSET CURRENT [nA] 50 5 4 100mV overdrive 3 20mV overdrive 5mV overdrive 2 1 0 -50 -25 0 25 50 75 100 125 150 AMBIENT TEMPERATURE [℃] Fig.108 Response Time (High to Low) - Over Drive Voltage Fig.109 Response Time (High to Low) - Ambient Temperature (VCC=5[V],VRL=5[V],RL=5.1[kΩ]) (VCC=5[V],VRL=5[V],RL=5.1[kΩ]) (*)The data above is ability value of sample, it is not guaranteed. BA2901:-40[℃]~+125[℃] BA2901S:-40[℃]~+105[℃] www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 15/24 2011.08 - Rev.B BA10393F,BA10339F,BA10339FV,BA2903SF,BA2903SFV,BA2903SFVM,BA2903F,BA2903FV, BA2903FVM,BA2901SF,BA2901SFV,BA2901SKN,BA2901F,BA2901FV,BA2901KN,BA8391G Technical Note ●Circuit Diagram VCC VOUT +IN -IN VEE Fig.110 Schematic Diagram (one channel only) ●Test Circuit1 Null Method Parameter VCC, VEE, EK, Vicm Unit : [V], VRL=VCC BA10393 family BA8391 family BA10339 family BA2903/BA2901 family Calculation VCC VEE EK Vicm VCC VEE EK Vicm VF S1 S2 S3 Input Offset Voltage VF1 ON ON ON 5 0 -1.4 0 5~36 0 -1.4 0 1 Input Offset Current VF2 OFF OFF ON 5 0 -1.4 0 5 0 -1.4 0 2 VF3 VF4 VF5 VF6 OFF ON ON OFF ON ON ON 5 5 15 15 0 0 0 0 -1.4 -1.4 -1.4 -11.4 0 0 0 0 5 5 15 15 0 0 0 0 -1.4 -1.4 -1.4 -11.4 0 0 0 0 Input Bias Current Large Signal Voltage Gain ON 3 4 - Calculation 1. Input Offset Voltage (Vio) Vio VF1 [V] 1+ R f /Rs 2. Input Offset Current (Iio) Iio Rf 50 [kΩ] VF2 - VF1 Ri (1+ R f / Rs) [A] S1 Rs 3. Input Bias Current (Ib) Ib VF4 - VF3 [A] 2× R i (1+ R f / Rs) Av = 20×Log |VF5-VF6| www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. +15[V] 50 [Ω] Ri 10 [kΩ] Rs 0.1 [µF] S2 4. Large Signal Voltage Gain (AV) C1 0.01 [µF] VCC Ri 10 [kΩ] Vicm RK 500 [kΩ] 0.1 [µF] 50 [Ω] 50k ΔEK×(1+Rf /Rs) EK RK 500 [kΩ] DUT NULL S3 VEE V RL VRL -15[V] Fig.111 Test circuit1 (one channel only) [dB] 16/24 2011.08 - Rev.B VF BA10393F,BA10339F,BA10339FV,BA2903SF,BA2903SFV,BA2903SFVM,BA2903F,BA2903FV, BA2903FVM,BA2901SF,BA2901SFV,BA2901SKN,BA2901F,BA2901FV,BA2901KN,BA8391G Technical Note ●Test Circuit 2: Switch Condition SW No. Supply Current SW 1 SW 2 SW 3 SW 4 SW 5 SW 6 SW 7 OFF OFF OFF OFF OFF OFF OFF Output Sink Current VOL=1.5[V] OFF ON ON OFF OFF OFF ON Saturation Voltage IOL=4[mA] OFF ON ON OFF ON ON OFF Output Leakage Current VOH=36[V] OFF ON ON OFF OFF OFF ON Response Time RL=5.1[kΩ], VRL=5[V] ON OFF ON ON OFF OFF OFF VCC A - SW1 SW2 + SW3 SW4 VEE VIN- SW5 SW6 RL V A VOL/VOH VRL VIN+ SW7 Fig.112 Test Circuit 2 (one channel only) VIN VIN Input wave +100mV Input wave 0V overdrive voltage overdrive voltage 0V -100mV VOUT VOUT Output wave VCC Output wave VCC VCC/2 VCC/2 0V 0V Tre (LOW to HIGH) Tre (HIGH to LOW) Fig.113 Response Time www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 17/24 2011.08 - Rev.B BA10393F,BA10339F,BA10339FV,BA2903SF,BA2903SFV,BA2903SFVM,BA2903F,BA2903FV, BA2903FVM,BA2901SF,BA2901SFV,BA2901SKN,BA2901F,BA2901FV,BA2901KN,BA8391G Technical Note ●Description of electrical characteristics Described below are descriptions of the relevant electrical terms. Please note that item names, symbols, and their meanings may differ from those on another manufacturer’s documents. 1. Absolute maximum ratings The absolute maximum ratings are values that should never be exceeded, since doing so may result in deterioration of electrical characteristics or damage to the part itself as well as peripheral components. 1.1 Power supply voltage (VCC/VEE) Expresses the maximum voltage that can be supplied between the positive and negative power supply terminals without causing deterioration of the electrical characteristics or destruction of the internal circuitry. 1.2 Differential input voltage (Vid) Indicates the maximum voltage that can be supplied between the non-inverting and inverting terminals without damaging the IC. 1.3 Input common-mode voltage range (Vicm) Signifies the maximum voltage that can be supplied to non-inverting and inverting terminals without causing deterioration of the electrical characteristics or damage to the IC itself. Normal operation is not guaranteed within the input common-mode voltage range of the maximum ratings – use within the input common-mode voltage range of the electric characteristics instead. 1.4 Power dissipation (Pd) Indicates the power that can be consumed by a particular mounted board at ambient temperature (25℃). For packaged products, Pd is determined by maximum junction temperature and the thermal resistance. 2. Electrical characteristics 2.1 Input offset voltage (Vio) Signifies the voltage difference between the non-inverting and inverting terminals. It can be thought of as the input voltage difference required for setting the output voltage to 0V. 2.2 Input offset current (Iio) Indicates the difference of the input bias current between the non-inverting and inverting terminals. 2.3 Input bias current (Ib) Denotes the current that flows into or out of the input terminal, it is defined by the average of the input bias current at the non-inverting terminal and the input bias current at the inverting terminal. 2.4 Input common-mode voltage range (Vicm) Indicates the input voltage range under which the IC operates normally. 2.5 Large signal voltage gain (AV) The amplifying rate (gain) of the output voltage against the voltage difference between the non-inverting and inverting terminals, it is (normally) the amplifying rate (gain) with respect to DC voltage. AV = (output voltage fluctuation) / (input offset fluctuation) 2.6 Circuit current (ICC) Indicates the current of the IC itself that flows under specific conditions and during no-load steady state. 2.7 Output sink current (IOL) Denotes the maximum current that can be output under specific output conditions. 2.8 Output saturation voltage low level output voltage (VOL) Signifies the voltage range that can be output under specific output conditions. 2.9 Output leakage current, High level output current (ILeak) Indicates the current that flows into the IC under specific input and output conditions. 2.10 Response time (tre) The interval between the application of input and output conditions. 2.11 Common-mode rejection ratio (CMRR) Denotes the ratio of fluctuation of the input offset voltage when the in-phase input voltage is changed (DC fluctuation). CMRR = (change of input common-mode voltage) / (input offset fluctuation) 2.12 Power supply rejection ratio (PSRR) Signifies the ratio of fluctuation of the input offset voltage when the supply voltage is changed (DC fluctuation). PSRR = (change in power supply voltage) / (input offset fluctuation) www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 18/24 2011.08 - Rev.B BA10393F,BA10339F,BA10339FV,BA2903SF,BA2903SFV,BA2903SFVM,BA2903F,BA2903FV, BA2903FVM,BA2901SF,BA2901SFV,BA2901SKN,BA2901F,BA2901FV,BA2901KN,BA8391G Technical Note ●Derating curves Power dissipation(total loss) indicates the power that can be consumed by IC at Ta=25℃(normal temperature).IC is heated when it consumed power, and the temperature of IC chip becomes higher than ambient temperature. The temperature that can be accepted by IC chip depends on circuit configuration, manufacturing process, and consumable power is limited. Power dissipation is determined by the temperature allowed in IC chip (maximum junction temperature) and thermal resistance of package (heat dissipation capability). The maximum junction temperature is typically equal to the maximum value in the storage temperature range. Heat generated by consumed power of IC radiates from the mold resin or lead frame of the package. The parameter which indicates this heat dissipation capability(hardness of heat release)is called thermal resistance, represented by the symbol θja [℃/W].The temperature of IC inside the package can be estimated by this thermal resistance. Fig.114 (a) shows the model of thermal resistance of the package. Thermal resistance θja, ambient temperature Ta, junction temperature Tj, and power dissipation Pd can be calculated by the equation below: θja = (Tj-Ta) / Pd [℃/W] ・・・・・ (Ⅰ) Derating curve in Fig.114 (b) indicates power that can be consumed by IC with reference to ambient temperature. Power that can be consumed by IC begins to attenuate at certain ambient temperature. This gradient iis determined by thermal resistance θja. Thermal resistance θja depends on chip size, power consumption, package, ambient temperature, package condition, wind velocity, etc even when the same of package is used. Thermal reduction curve indicates a reference value measured at a specified condition. Fig.115(c) ~ (f) shows a derating curve for an example of BA8391, BA10393, BA10339, BA2903S, BA2903, BA2901S, and BA2901. LSIの 消of 費LSI 電 力 [W] Power dissipation Pd (max) θja = ( Tj ー Ta ) / Pd [℃/W] P2 θja2 < θja1 周囲温度 Ta [℃] Ambient temperature θ' ja2 P1 θ ja2 Tj ' (max) θ' ja1 ップ 表面温度 Tj [℃] Chip surfaceチ temperature 0 Power dissipation 消費電力 P [W] 25 50 Tj (max) θ ja1 75 100 125 150 周 囲 温 度 Ta [℃ ] Ambient temperature (b) Derating curve (a) Thermal resistance Fig.114 Thermal resistance and derating curve 1000 1000 Pd [mW] 許容損失 POWER DISSIPATION Pd [mW] POWER DISSIPATION Pd [mW] 許容損失 Pd [mW] 1000 800 BA10393F 620mW(★16) 600 400 200 800 800 BA10339FV 700mW(★17) 600 600 490mW(★18) BA10339F 400 400 200 200 0 0 0 0 25 50 75 100 00 125 Ambient Temperature [℃] Ta [°C] 周囲温度 25 25 50 50 (c)BA10393 family 125 125 (d)BA10339 family 1000 870mW(★22) 780mW(★19) BA2903F POWER DISSIPATION [mW] 許容損失 Pd Pd[mW] POWER DISSIPATION [mW] 許容損失 Pd Pd[mW] 100 100 周囲温度 Ta [°C] 1000 800 75 75 Ambient Temperature [℃] BA2903FV 690mW(★20) BA2903FVM 600 ★ 590mW( 21) BA2903SF 400 200 BA2903SFV BA2903SFVM 0 0 25 50 75 105 100 BA2901FV 800 660mW(★23) 600 BA2901KN 610mW(★24) BA2901F BA2901SFV 400 200 BA2901SKN BA2901SF 0 125 0 150 25 50 75 105 100 Ambient Temperature [℃] Ta [°C] 周囲温度 Ambient Temperature [℃] Ta [°C] 周囲温度 (e)BA2903 family (f)BA2901 family 125 150 (*16) (*17) (*18) (*19) (*20) (*21) (*22) (*23) (*24) Unit 6.2 7.0 4.9 6.2 5.5 4.7 7.0 5.3 4.9 [mW/℃] When using the unit above Ta=25[℃], subtract the value above per degree[℃]. Permissible dissipation is the value when FR4 glass epoxy board 70[mm] ×70[mm] ×1.6[mm] (cooper foil area below 3[%]) is mounted. Fig.115 Derating curve www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 19/24 2011.08 - Rev.B BA10393F,BA10339F,BA10339FV,BA2903SF,BA2903SFV,BA2903SFVM,BA2903F,BA2903FV, BA2903FVM,BA2901SF,BA2901SFV,BA2901SKN,BA2901F,BA2901FV,BA2901KN,BA8391G Technical Note ●Notes for use 1) Unused circuits When there are unused circuits it is recommended that they be connected as in Fig.116, setting the non-inverting input terminal to a potential within the in-phase input voltage range (VICR). VCC + Please keep this potential in Vicm OPEN - VEE Fig.116 Disable circuit example 2) Input terminal voltage (BA8391 / BA2903 / BA2901 family)Applying VEE + 36V to the input terminal is possible without causing deterioration of the electrical characteristics or destruction, irrespective of the supply voltage. However, this does not ensure normal circuit operation. Please note that the circuit operates normally only when the input voltage is within the common mode input voltage range of the electric characteristics. 3) Power supply (signal / dual) The op-amp operates when the specified voltage supplied is between VCC and VEE. Therefore, the signal supply op-amp can be used as a dual supply op-amp as well. 4) Power dissipation Pd Using the unit in excess of the rated power dissipation may cause deterioration in electrical characteristics due to a rise in chip temperature, including reduced current capability. Therefore, please take into consideration the power dissipation (Pd) under actual operating conditions and apply a sufficient margin in thermal design. Refer to the thermal derating curves for more information. 5) Short-circuit between pins and erroneous mounting Incorrect mounting may damage the IC. In addition, the presence of foreign particles between the outputs, the output and the power supply, or the output and GND may result in IC destruction. 6) Terminal short-circuits When the output and VCC terminals are shorted, excessive output current may flow, resulting in undue heat generation and, subsequently, destruction. 7) Operation in a strong electromagnetic field Operation in a strong electromagnetic field may cause malfunctions. 8) Radiation This IC is not designed to withstand radiation. 9) IC handing Applying mechanical stress to the IC by deflecting or bending the board may cause fluctuations in the electrical characteristics due to piezoelectric (piezo) effects. 10) Board inspection Connecting a capacitor to a pin with low impedance may stress the IC. Therefore, discharging the capacitor after every process is recommended. In addition, when attaching and detaching the jig during the inspection phase, ensure that the power is turned off before inspection and removal. Furthermore, please take measures against ESD in the assembly process as well as during transportation and storage. www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 20/24 2011.08 - Rev.B BA10393F,BA10339F,BA10339FV,BA2903SF,BA2903SFV,BA2903SFVM,BA2903F,BA2903FV, BA2903FVM,BA2901SF,BA2901SFV,BA2901SKN,BA2901F,BA2901FV,BA2901KN,BA8391G Technical Note ●Example of circuit ○Reference voltage is VinVoltage VCC Reference voltage + Vin Vout - Time Reference voltage Input voltage wave Voltage High VEE While input voltage is bigger than reference voltage, output voltage is high. While input voltage is smaller than reference voltage, output voltage is low. Low Time Output voltage wave ○Reference voltage is Vin+ Voltage VCC Reference voltage + Reference voltage Vin Vout - Time Input voltage wave VEE High While input voltage is smaller than reference voltage, output voltage is high. While input voltage is bigger than reference voltage, output voltage is low. Low Time Output voltage wave www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 21/24 2011.08 - Rev.B BA10393F,BA10339F,BA10339FV,BA2903SF,BA2903SFV,BA2903SFVM,BA2903F,BA2903FV, BA2903FVM,BA2901SF,BA2901SFV,BA2901SKN,BA2901F,BA2901FV,BA2901KN,BA8391G Technical Note ●Ordering part number B A 2 Part No. 9 0 3 F Part No. 10393, 10339 2903S, 2903 2901S, 2901 8391 V - Package G : SSOP5 F : SOP8 SOP14 FV : SSOP-B8 SSOP-B14 FVM : MSOP8 KN : VQFN16 E 2 Packaging and forming specification E2: Embossed tape and reel (SOP8/SOP14/SSOP-B8/SSOP-B14/VQFN16) TR: Embossed tape and reel (SSOP5/MSOP8) SSOP5 5 4 1 2 3 Tape Embossed carrier tape Quantity 3000pcs Direction of feed 0.2Min. +0.2 1.6 −0.1 2.8±0.2 <Tape and Reel information> +6° 4° −4° 2.9±0.2 TR The direction is the 1pin of product is at the upper right when you hold ( reel on the left hand and you pull out the tape on the right hand 1pin +0.05 0.13 −0.03 1.25Max. ) +0.05 0.42 −0.04 0.05±0.05 1.1±0.05 S 0.95 0.1 S Direction of feed Reel (Unit : mm) ∗ Order quantity needs to be multiple of the minimum quantity. SOP8 <Tape and Reel information> 6 5 +6° 4° −4° 0.3MIN 7 4.4±0.2 6.2±0.3 8 1 2 3 0.9±0.15 5.0±0.2 (MAX 5.35 include BURR) Tape Embossed carrier tape Quantity 2500pcs Direction of feed E2 The direction is the 1pin of product is at the upper left when you hold ( reel on the left hand and you pull out the tape on the right hand ) 4 0.595 1.5±0.1 +0.1 0.17 -0.05 0.11 S 1.27 0.42±0.1 1pin Reel (Unit : mm) www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 22/24 Direction of feed ∗ Order quantity needs to be multiple of the minimum quantity. 2011.08 - Rev.B BA10393F,BA10339F,BA10339FV,BA2903SF,BA2903SFV,BA2903SFVM,BA2903F,BA2903FV, BA2903FVM,BA2901SF,BA2901SFV,BA2901SKN,BA2901F,BA2901FV,BA2901KN,BA8391G Technical Note SOP14 <Tape and Reel information> 8.7 ± 0.2 (MAX 9.05 include BURR) 8 Tape Embossed carrier tape Quantity 2500pcs Direction of feed 0.3MIN 4.4±0.2 6.2±0.3 14 1 E2 The direction is the 1pin of product is at the upper left when you hold ( reel on the left hand and you pull out the tape on the right hand ) 7 1.5±0.1 0.15 ± 0.1 0.4 ± 0.1 0.11 1.27 0.1 1pin Reel (Unit : mm) Direction of feed ∗ Order quantity needs to be multiple of the minimum quantity. SSOP-B8 <Tape and Reel information> 3.0 ± 0.2 (MAX 3.35 include BURR) 0.3MIN 4.4±0.2 6.4±0.3 8 76 5 Tape Embossed carrier tape Quantity 2500pcs Direction of feed E2 The direction is the 1pin of product is at the upper left when you hold ( reel on the left hand and you pull out the tape on the right hand ) 1.15±0.1 1 23 4 0.15 ± 0.1 0.1 S 0.1 +0.06 0.22 -0.04 (0.52) 0.08 M 0.65 1pin Reel (Unit : mm) Direction of feed ∗ Order quantity needs to be multiple of the minimum quantity. SSOP-B14 <Tape and Reel information> 5.0 ± 0.2 8 0.3Min. 4.4 ± 0.2 6.4 ± 0.3 14 1 Tape Embossed carrier tape Quantity 2500pcs Direction of feed E2 The direction is the 1pin of product is at the upper left when you hold ( reel on the left hand and you pull out the tape on the right hand ) 7 0.10 1.15 ± 0.1 0.15 ± 0.1 0.65 0.1 0.22 ± 0.1 1pin Reel (Unit : mm) www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 23/24 Direction of feed ∗ Order quantity needs to be multiple of the minimum quantity. 2011.08 - Rev.B BA10393F,BA10339F,BA10339FV,BA2903SF,BA2903SFV,BA2903SFVM,BA2903F,BA2903FV, BA2903FVM,BA2901SF,BA2901SFV,BA2901SKN,BA2901F,BA2901FV,BA2901KN,BA8391G Technical Note MSOP8 <Tape and Reel information> 2.8±0.1 4.0±0.2 8 7 6 5 0.6±0.2 +6° 4° −4° 0.29±0.15 2.9±0.1 (MAX 3.25 include BURR) Tape Embossed carrier tape Quantity 3000pcs Direction of feed TR The direction is the 1pin of product is at the upper right when you hold ( reel on the left hand and you pull out the tape on the right hand ) 1 2 3 4 1PIN MARK 1pin +0.05 0.145 –0.03 0.475 +0.05 0.22 –0.04 0.08±0.05 0.75±0.05 0.9MAX S 0.08 S Direction of feed 0.65 Reel (Unit : mm) ∗ Order quantity needs to be multiple of the minimum quantity. VQFN16 <Tape and Reel information> 4.2±0.1 4.0±0.1 (1.35) 4.0±0.1 9 1 4 0.05 M +0.03 0.02 −0.02 0.22±0.05 2500pcs Direction of feed 5 16 E2 The direction is the 1pin of product is at the upper left when you hold ( reel on the left hand and you pull out the tape on the right hand ) 0.05 (0 .2 2) 0.5 Embossed carrier tape (with dry pack) Quantity 8 13 0.22±0.05 Tape 0.95MAX 4.2±0.1 12 ) .5 (0 5) .3 (0 3- +0.1 0.6 −0.3 www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. Notice : Do not use the dotted line area for soldering 1pin Reel (Unit : mm) 24/24 Direction of feed ∗ Order quantity needs to be multiple of the minimum quantity. 2011.08 - Rev.B Notice Notes No copying or reproduction of this document, in part or in whole, is permitted without the consent of ROHM Co.,Ltd. The content specified herein is subject to change for improvement without notice. The content specified herein is for the purpose of introducing ROHM's products (hereinafter "Products"). If you wish to use any such Product, please be sure to refer to the specifications, which can be obtained from ROHM upon request. Examples of application circuits, circuit constants and any other information contained herein illustrate the standard usage and operations of the Products. The peripheral conditions must be taken into account when designing circuits for mass production. Great care was taken in ensuring the accuracy of the information specified in this document. However, should you incur any damage arising from any inaccuracy or misprint of such information, ROHM shall bear no responsibility for such damage. The technical information specified herein is intended only to show the typical functions of and examples of application circuits for the Products. ROHM does not grant you, explicitly or implicitly, any license to use or exercise intellectual property or other rights held by ROHM and other parties. ROHM shall bear no responsibility whatsoever for any dispute arising from the use of such technical information. The Products specified in this document are intended to be used with general-use electronic equipment or devices (such as audio visual equipment, office-automation equipment, communication devices, electronic appliances and amusement devices). The Products specified in this document are not designed to be radiation tolerant. While ROHM always makes efforts to enhance the quality and reliability of its Products, a Product may fail or malfunction for a variety of reasons. Please be sure to implement in your equipment using the Products safety measures to guard against the possibility of physical injury, fire or any other damage caused in the event of the failure of any Product, such as derating, redundancy, fire control and fail-safe designs. ROHM shall bear no responsibility whatsoever for your use of any Product outside of the prescribed scope or not in accordance with the instruction manual. The Products are not designed or manufactured to be used with any equipment, device or system which requires an extremely high level of reliability the failure or malfunction of which may result in a direct threat to human life or create a risk of human injury (such as a medical instrument, transportation equipment, aerospace machinery, nuclear-reactor controller, fuelcontroller or other safety device). ROHM shall bear no responsibility in any way for use of any of the Products for the above special purposes. If a Product is intended to be used for any such special purpose, please contact a ROHM sales representative before purchasing. If you intend to export or ship overseas any Product or technology specified herein that may be controlled under the Foreign Exchange and the Foreign Trade Law, you will be required to obtain a license or permit under the Law. Thank you for your accessing to ROHM product informations. More detail product informations and catalogs are available, please contact us. ROHM Customer Support System http://www.rohm.com/contact/ www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. R1120A