AD AD8223BR-RL Single-supply, low cost instrumentation amplifier Datasheet

Single-Supply, Low Cost
Instrumentation Amplifier
AD8223
Gain set with 1 resistor
Gain = 5 to 1000
Inputs
Voltage range to 150 mV below negative rail
25 nA maximum input bias current
30 nV/√Hz, RTI noise @ 1 kHz
Power supplies
Dual supply: ±2 V to ±12 V
Single supply: 3 V to 24 V
500 μA maximum supply current
APPLICATIONS
Low power medical instrumentation
Transducer interface
Thermocouple amplifiers
Industrial process controls
Difference amplifiers
Low power data acquisition
CONNECTION DIAGRAM
–RG
1
8
+RG
–IN
2
–
7
+VS
+IN
3
+
6
OUT
–VS
4
5
REF
AD8223
06925-001
FEATURES
Figure 1. 8-Lead SOIC (R) and 8-Lead MSOP (RM) Packages
Table 1. Instrumentation Amplifiers by Category
GeneralPurpose
AD82201
AD8221
AD8222
AD82241
AD8228
1
Zero Drift
AD82311
AD85531
AD85551
AD85561
AD85571
Mil
Grade
AD620
AD621
AD524
AD526
AD624
Low
Power
AD6271
AD6231
AD8223
High Voltage
PGA
AD8250
AD8251
AD8253
Rail-to-rail output.
GENERAL DESCRIPTION
The AD8223 is an integrated single-supply instrumentation
amplifier that delivers rail-to-rail output swing on a single
supply (3 V to 24 V). The AD8223 conforms to the 8-lead
industry standard pinout configuration.
The AD8223 is simple to use: one resistor sets the gain. With no
external resistor, the AD8223 is configured for G = 5. With an
external resistor, the AD8223 can be programmed for gains up
to 1000.
The AD8223 has a wide input common-mode range and can
amplify signals that have a 150 mV common-mode voltage
below ground. Although the design of the AD8223 is optimized
to operate from a single supply, the AD8223 still provides
excellent performance when operated from a dual voltage
supply (±2 V to ±12 V).
Low power consumption (1.5 mW at 3 V), wide supply voltage
range, and rail-to-rail output swing make the AD8223 ideal for
battery-powered applications. The rail-to-rail output stage
maximizes the dynamic range when operating from low supply
voltages. The AD8223 replaces discrete instrumentation
amplifier designs and offers superior linearity, temperature
stability, and reliability in a minimum of space.
Rev. 0
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113
©2008 Analog Devices, Inc. All rights reserved.
AD8223* Product Page Quick Links
Last Content Update: 11/01/2016
Comparable Parts
Reference Materials
View a parametric search of comparable parts
Technical Articles
• High-performance Adder Uses Instrumentation Amplifiers
Evaluation Kits
• AD62x, AD822x, AD842x Series InAmp Evaluation Board
Documentation
Application Notes
• AN-1401: Instrumentation Amplifier Common-Mode
Range: The Diamond Plot
Data Sheet
• AD8223: Single Supply, Rail-to-Rail, Low Cost
Instrumentation Amplifier Data Sheet
Technical Books
• A Designer's Guide to Instrumentation Amplifiers, 3rd
Edition, 2006
User Guides
• UG-261: Evaluation Boards for the AD62x, AD822x and
AD842x Series
Design Resources
•
•
•
•
AD8223 Material Declaration
PCN-PDN Information
Quality And Reliability
Symbols and Footprints
Discussions
View all AD8223 EngineerZone Discussions
Sample and Buy
Visit the product page to see pricing options
Technical Support
Submit a technical question or find your regional support
number
* This page was dynamically generated by Analog Devices, Inc. and inserted into this data sheet. Note: Dynamic changes to
the content on this page does not constitute a change to the revision number of the product data sheet. This content may be
frequently modified.
AD8223
TABLE OF CONTENTS
Features .............................................................................................. 1
Gain Selection ............................................................................. 14
Applications ....................................................................................... 1
Input Voltage Range ................................................................... 14
Connection Diagram ....................................................................... 1
Reference Terminal .................................................................... 15
General Description ......................................................................... 1
Input Protection ......................................................................... 15
Revision History ............................................................................... 2
RF Interference (RFI)................................................................. 15
Specifications..................................................................................... 3
Ground Returns for Input Bias Currents ................................ 16
Single Supply ................................................................................. 3
Applications Information .............................................................. 17
Dual Supply ................................................................................... 5
Basic Connection ....................................................................... 17
Absolute Maximum Ratings............................................................ 7
Differential Output .................................................................... 17
Thermal Resistance ...................................................................... 7
Output Buffering ........................................................................ 17
ESD Caution .................................................................................. 7
Cables ........................................................................................... 17
Pin Configuration and Function Descriptions ............................. 8
A Single-Supply Data Acquisition System .............................. 18
Typical Performance Characteristics ............................................. 9
Amplifying Signals with Low Common-Mode Voltage ........ 18
Theory of Operation ...................................................................... 14
Outline Dimensions ....................................................................... 19
Amplifier Architecture .............................................................. 14
Ordering Guide .......................................................................... 20
REVISION HISTORY
10/08—Revision 0: Initial Version
Rev. 0 | Page 2 of 20
AD8223
SPECIFICATIONS
SINGLE SUPPLY
TA = 25°C, −VS = 0 V, +VS = +5 V, and RL = 10 kΩ to 2.5 V, unless otherwise noted.
Table 2
Parameter
COMMON-MODE REJECTION RATIO
DC to 60 Hz with 1 kΩ Source
Imbalance
G=5
G = 10
G = 100
G = 1000
NOISE
Voltage Noise, 1 kHz
G=5
G = 1000
RTI, 0.1 Hz to 10 Hz
G=5
G = 1000
Current Noise, 1 kHz
0.1 Hz to 10 Hz
VOLTAGE OFFSET
Input Offset, VOSI
Over Temperature
Average TC
Output Offset, VOSO
Over Temperature
Average TC
Offset Referred to Input vs.
Supply (PSR)
G=5
G = 10
G = 100
G = 1000
INPUT CURRENT
Input Bias Current
Over Temperature
Average Temperature
Coefficient
Input Offset Current
Over Temperature
Average Temperature
Coefficient
DYNAMIC RESPONSE
Small Signal −3 dB Bandwidth
G=5
G = 10
G = 100
G = 1000
Slew Rate
Conditions
Min
AD8223A
Typ
Max
Min
AD8223B
Typ
Max
Unit
VCM = 0 V to 3 V
80
86
90
90
86
90
96
96
dB
dB
dB
dB
VIN+ = VIN− = VREF = 0 V
50
30
50
30
nV/√Hz
nV/√Hz
1.0
0.6
70
1.2
1.0
0.6
70
1.2
μV p-p
μV p-p
fA/√Hz
pA p-p
Total RTI error =
VOSI + VOSO/G
250
400
2
1500
2000
15
TA = −40°C to +85°C
TA = −40°C to +85°C
TA = −40°C to +85°C
TA = −40°C to +85°C
+VS = 4 V to 24 V,
−VS = 0 V
80
86
90
90
TA = −40°C to +85°C
TA = −40°C to +85°C
5
5
86
90
96
96
12
25
28
50
0.25
TA = −40°C to +85°C
TA = −40°C to +85°C
100
160
1
1000
1500
10
5
5
dB
dB
dB
dB
12
25
28
nA
nA
pA/°C
2
2.5
50
5
5
nA
nA
pA/°C
125
125
50
5
0.2
125
125
50
5
0.2
kHz
kHz
kHz
kHz
V/μs
Rev. 0 | Page 3 of 20
2
2.5
μV
μV
μV/°C
μV
μV
μV/°C
0.25
AD8223
Parameter
Settling Time to 0.01%
G=5
G = 10
G = 100
G = 1000
GAIN
Gain Range
Gain Error1
G=5
G = 10
G = 100
G = 1000
Nonlinearity
G=5
G = 1000
Gain vs. Temperature
G=5
G > 51
INPUT
Input Impedance
Differential
Common-Mode
Common-Mode Input Voltage
Range2
OUTPUT
Output Swing
REFERENCE INPUT
RIN
IIN
Voltage Range
Gain to Output
POWER SUPPLY
Operating Range
Quiescent Current
Over Temperature
TEMPERATURE RANGE
For Specified Performance
1
2
Conditions
Step size = 3.5 V
Min
AD8223A
Typ
Max
Min
18
18
18
85
AD8223B
Typ
Max
18
18
18
85
Unit
μs
μs
μs
μs
G = 5 + (80 kΩ/RG)
5
1000
5
1000
V/V
0.02
0.2
0.3
0.3
%
%
%
%
VOUT = 0.05 V to 4.5 V
0.10
0.10
0.10
0.07
0.3
0.3
0.3
0.10
0.10
0.10
VOUT = 0.05 V to 4.5 V
12
200
12
200
ppm
ppm
TA = −40°C to +85°C
10
2
50
50
2||2
2||2
2||2
2||2
ppm/°C
ppm/°C
GΩ||pF
GΩ||pF
V
VIN+ = VIN−
(−VS) −
0.15
(+VS) −
1.5
(−VS) −
0.15
(+VS) −
1.5
RL = 10 kΩ to ground
+0.01
+0.01
+0.01
(+VS) −
0.5
(+VS) −
0.15
V
RL = 100 kΩ to ground
(+VS) −
0.5
(+VS) −
0.15
±20%
+20
+VS
kΩ
μA
V
V
+24
500
600
V
μA
μA
+85
°C
60
+10
VIN+ = VIN− = VREF = 0 V
−VS
±20%
+20
+VS
+0.01
60
+10
−VS
1±
0.0002
+3
350
TA = −40°C to +85°C
-40
1±
0.0002
+24
500
600
+3
+85
−40
350
V
Does not include effects of external resistor, RG.
Total input range depends on common-mode voltage, differential voltage, and gain. See Figure 18 through Figure 21, and the Input Voltage Range section in the
Theory of Operation section for more information.
Rev. 0 | Page 4 of 20
AD8223
DUAL SUPPLY
TA = 25°C, −VS = −12 V, +VS = +12 V, and RL = 10 kΩ to ground, unless otherwise noted.1
Table 3.
Parameter
COMMON-MODE REJECTION RATIO
DC to 60 Hz with 1 kΩ Source
Imbalance
G=5
G = 10
G = 100
G = 1000
NOISE
Voltage Noise, 1 kHz
G=5
G = 1000
RTI, 0.1 Hz to 10 Hz
G=5
G = 1000
Current Noise, 1 kHz
0.1 Hz to 10 Hz
VOLTAGE OFFSET
Input Offset, VOSI
Over Temperature
Average TC
Output Offset, VOSO
Over Temperature
Average TC
Offset Referred to Input vs.
Supply (PSR)
G=5
G = 10
G = 100
G = 1000
INPUT CURRENT
Input Bias Current
Over Temperature
Average Temperature
Coefficient
Input Offset Current
Over Temperature
Average Temperature
Coefficient
DYNAMIC RESPONSE
Small Signal −3 dB Bandwidth
G=5
G = 10
G = 100
G = 1000
Slew Rate
Settling Time to 0.01%
G=5
G = 10
G = 100
G = 1000
Conditions
Min
AD8223A
Typ
Max
Min
AD8223B
Typ
Max
Unit
VCM = −10 V to 10 V
80
86
90
90
86
90
96
96
dB
dB
dB
dB
VIN+ = VIN− = VREF = 0 V
50
30
50
30
nV/√Hz
nV/√Hz
1.0
0.6
70
1.2
1.0
0.6
70
1.2
μV p-p
μV p-p
fA/√Hz
pA p-p
Total RTI error =
VOSI + VOSO/G
250
400
2
1500
2000
15
TA = −40°C to +85°C
TA = −40°C to +85°C
TA = −40°C to +85°C
TA = −40°C to +85°C
+VS = 5 V to 12 V,
−VS = −5 V to −12 V
80
86
90
90
TA = −40°C to +85°C
TA = −40°C to +85°C
5
5
86
90
96
96
12
25
28
50
0.25
TA = −40°C to +85°C
TA = −40°C to +85°C
100
160
1
1000
1500
10
5
5
dB
dB
dB
dB
12
25
28
nA
nA
pA/°C
2
2.5
50
2
2.5
μV
μV
μV/°C
μV
μV
μV/°C
0.25
5
5
nA
nA
pA/°C
200
200
70
7
0.3
200
200
70
7
0.3
kHz
kHz
kHz
kHz
V/μs
30
30
30
150
30
30
30
150
μs
μs
μs
μs
Step size = 10 V
Rev. 0 | Page 5 of 20
AD8223
Parameter
GAIN
Gain Range
Gain Error2
G=5
G = 10
G = 100
G = 1000
Nonlinearity
G=5
G = 1000
Gain vs. Temperature
G=5
G > 51
INPUT
Input Impedance
Differential
Common-Mode
Common-Mode Input Voltage
Range3
OUTPUT
Output Swing
Conditions
G = 5 + (80 kΩ/RG)
POWER SUPPLY
Operating Range
Quiescent Current
Over Temperature
TEMPERATURE RANGE
For Specified Performance
AD8223A
Typ
5
Max
Min
1000
5
AD8223B
Typ
Max
Unit
1000
V/V
0.02
0.2
0.3
0.3
%
%
%
%
VOUT = −10 V to +10 V
0.10
0.10
0.10
0.07
0.3
0.3
0.3
0.10
0.10
0.10
VOUT = −10 V to +10 V
5
30
5
30
ppm
ppm
TA = −40°C to +85°C
10
2
50
50
2||2
2||2
2||2
2||2
ppm/°C
ppm/°C
GΩ||pF
GΩ||pF
V
VIN+ = VIN−
(−VS) −
0.15
(+VS) −
1.5
(−VS) −
0.15
(+VS) −
1.5
RL = 10 kΩ to ground
(−VS) +
0.3
(−VS) +
0.1
(+VS) −
0.8
(+VS) −
0.3
(−VS) +
0.3
(−VS) +
0.1
(+VS) −
0.8
(+VS) −
0.3
V
±20%
+20
+VS
kΩ
μA
V
V
RL = 100 kΩ to ground
REFERENCE INPUT
RIN
IIN
Voltage Range
Gain to Output
Min
60
+10
VIN+ = VIN− = VREF = 0 V
−VS
±20%
+20
+VS
60
+10
−VS
1±
0.0002
1±
0.0002
V
±2
±12
650
850
±2
±12
650
850
V
μA
μA
−40
+85
−40
+85
°C
TA = −40°C to +85°C
1
Because maximum supply voltage is 24 V between the negative and positive supply, these specifications at ±12V are at the part’s limit. Operation at a nominal supply
voltage slightly less than ±12 V is recommended to allow for power supply tolerances.
Does not include effects of external resistor, RG.
3
Total input range depends on common-mode voltage, differential voltage, and gain. See Figure 18 through Figure 21 and the Input Voltage Range section in the
Theory of Operation section for more information.
2
Rev. 0 | Page 6 of 20
AD8223
ABSOLUTE MAXIMUM RATINGS
THERMAL RESISTANCE
Table 4.
Parameter
Supply Voltage
Internal Power Dissipation
Differential Input Voltage
Output Short-Circuit Duration
Storage Temperature Range (R, RM)
Operating Temperature Range
Lead Temperature (Soldering, 10 sec)
ESD (Human Body Model)
ESD (Charge Device Model)
ESD (Machine Model)
θJA is specified for the worst-case conditions, that is, a device
soldered in a circuit board for surface-mount packages.
Rating
±12 V
650 mW
±VS
Indefinite
−65°C to +125°C
−40°C to +85°C
300°C
1.5 kV
500 V
100 V
Specification is for the device in free air.
Table 5. Thermal Resistance
Package Type
8-Lead SOIC (R)
8-Lead MSOP (RM)
ESD CAUTION
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
Rev. 0 | Page 7 of 20
θJA
155
200
Unit
°C/W
°C/W
AD8223
–RG
1
8
+RG
–IN
2
AD8223
7
3
TOP VIEW
(Not to Scale)
+VS
+IN
6
OUT
–VS
4
5
REF
06925-002
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
Figure 2. Pin Configuration
Table 6. Pin Function Descriptions
Pin No.
1
2
3
4
5
6
7
8
Mnemonic
−RG
−IN
+IN
−VS
REF
OUT
+VS
+RG
Descriptions
Gain Resistor Terminal.
Negative Input.
Positive Input.
Negative Supply.
Reference. Connect to a low impedance source. Output is referenced to this node.
Output.
Positive Supply.
Gain Resistor Terminal.
Rev. 0 | Page 8 of 20
AD8223
TYPICAL PERFORMANCE CHARACTERISTICS
TA = 25°C, VS = ±5 V, RL = 10 kΩ, unless otherwise noted.
1000
NUMBER OF UNITS
600
500
400
300
200
06925-061
100
0
–13.8
–13.5
–13.2
–12.9
–12.6
–12.3
100
G=5
G = 1000
BW LIMIT G = 100
BW LIMIT
10
0.1
–12.0
1
10
INPUT BIAS CURRENT (nA)
100
1k
100k
10k
FREQUENCY (Hz)
Figure 6. Voltage Noise Density vs. Frequency
Figure 3. Typical Distribution of Input Bias Current
25
N = 4720
MEAN = –0.00571517
SD = 0.172282
1000
G = 10
06925-050
700
VOLTAGE NOISE DENSITY (nV/ Hz)
N = 4720
MEAN = –12.9448
SD = 0.317868
IBIAS (nA)
600
400
15
10
5
06925-062
200
0
–0.9
–0.6
–0.3
0
0.3
0.6
0.9
0
–60
1.2
06925-064
NUMBER OF UNITS
20
800
–40
–20
INPUT OFFSET CURRENT (nA)
600
400
200
0
0.005
80
100
120
140
0.010
100
10
0.01
0.015
GAIN ERROR, G = 5 (%)
06925-065
CURRENT NOISE DENSITY (fA/ Hz)
800
06925-063
NUMBER OF UNITS
1000
–0.005
60
1000
1200
–0.010
40
Figure 7. IBIAS vs. Temperature
N = 5036
MEAN = –0.00336179
SD = 0.00155048
0
–0.015
20
TEMPERATURE (°C)
Figure 4. Typical Distribution of Input Offset Current
1400
0
0.1
1
10
100
FREQUENCY (Hz)
Figure 5. Typical Distribution for Gain Error (G = 5)
Figure 8. Current Noise Density vs. Frequency
Rev. 0 | Page 9 of 20
1k
AD8223
18
120
16
110
G = 1000
±VS = ±5V
14
±VS = ±2.5V
100
±VS = ±12V
G = 100
8
80
70
60
4
50
2
40
06925-013
6
0
–12
–10
–8
–6
–4
–2
0
2
4
6
30
10
8
G = 10
06925-055
CMRR (dB)
10
1
10
100
1k
10k
100k
FREQUENCY (Hz)
CMV (V)
Figure 12. CMRR vs. Frequency, ±VS = ±12
Figure 9. IBIAS vs. CMV
120
G = 1000
110
100
G=5
CMRR (dB)
90
G = 10
G = 100
80
70
60
50
40
30
06925-056
1s/DIV
06925-066
500fA/DIV
1
10
100
1k
10k
100k
FREQUENCY (Hz)
Figure 13. CMRR vs. Frequency, +VS = +5 V
Figure 10. 0.1 Hz to 10 Hz Current Noise
70
60
G = 1000
G = 1000
50
GAIN (dB)
40
G=5
G = 100
30
20
10
G = 10
G=5
0
0.5µV/DIV
1s/DIV
06925-018
–10
–20
06925-054
IBIAS (nA)
G=5
90
12
–30
100
1k
10k
100k
FREQUENCY (Hz)
Figure 14. Gain vs. Frequency, ±VS = ±12 V
Figure 11. 0.1 Hz to 10 Hz RTI and RTO Voltage Noise
Rev. 0 | Page 10 of 20
1M
AD8223
70
4
G = 1000
60
3
G = 100
40
30
G = 10
20
G=5
10
0
±VS = ±2.5V
0
+VS = +5V
–1
–2
–3
–4
06925-067
–10
1
–20
–30
100
1k
10k
–5
–6
–6
1M
100k
06925-070
GAIN (dB)
±VS = ±5V
2
COMMON-MODE INPUT (V)
50
–4
FREQUENCY (Hz)
–2
0
2
4
6
MAXIMUM OUTPUT VOLTAGE (V)
Figure 15. Gain vs. Frequency, +VS = +5 V
Figure 18. Common-Mode Input vs. Maximum Output Voltage,
G = 5, Small Supplies
25
15
±12V
10
COMMON-MODE INPUT (V)
15
±5V
10
±2.5V
5
5
0
–5
06925-068
–10
0
0.1
1
–15
–15
100
10
06925-071
OUTPUT VOLTAGE (V p-p)
20
–10
FREQUENCY (kHz)
0
5
10
15
Figure 19. Common-Mode Input vs. Maximum Output Voltage,
G = 5, ±VS = ±12 V
4
0.38
3
0.36
2
COMMON-MODE INPUT (V)
0.04
0.34
0.32
0.30
0.28
0.26
0.24
±VS = ±5V
1
±VS = ±2.5V
0
+VS = +5V
–1
–2
–3
0.22
2
4
6
8
10
12
06925-072
–4
06925-069
SLEW RATE (V/μs)
Figure 16. Large Signal Frequency Response
0.20
–5
MAXIMUM OUTPUT VOLTAGE (V)
–5
–6
–6
14
SUPPLY VOLTAGE (±VS)
–4
–2
0
2
4
6
MAXIMUM OUTPUT VOLTAGE (V)
Figure 17. Slew Rate vs. Supply Voltage
Figure 20. Common-Mode Input vs. Maximum Output Voltage,
G = 100, Small Supplies
Rev. 0 | Page 11 of 20
AD8223
15
120
10
100
5
80
0
G = 100
60
G = 10
40
–10
20
–15
–15
06925-073
–5
–10
–5
0
5
10
0
15
G=5
06925-025
PSRR (dB)
COMMON-MODE INPUT (V)
G = 1000
1
10
100
1k
10k
100k
FREQUENCY (Hz)
MAXIMUM OUTPUT VOLTAGE (V)
Figure 21. Common-Mode Input vs. Maximum Output Voltage,
G = 100, ±VS = ±12 V
Figure 24. Negative PSRR vs. Frequency, ±VS = ±12 V
140
120
5V/DIV
G = 1000
100
PSRR (dB)
G = 100
80
G = 10
60
G=5
0
06925-023
20
1
10
100
1k
10k
100µs/DIV
06925-051
0.1%/DIV
40
100k
FREQUENCY (Hz)
Figure 22. Positive PSRR vs. Frequency, ±VS = ±12 V
Figure 25. Large Signal Response, G = 5
140
120
5V/DIV
G = 1000
100
G = 10
G=5
0.1%/DIV
40
20
0
1
10
100
1k
10k
100µs/DIV
06925-052
60
06925-024
PSRR (dB)
G = 100
80
100k
FREQUENCY (Hz)
Figure 26. Large Signal Pulse Response, G = 100, CL = 100 pF
Figure 23. Positive PSRR vs. Frequency, +VS = +5 V
Rev. 0 | Page 12 of 20
AD8223
5V/DIV
0.1%/DIV
Figure 27. Large Signal Pulse Response, G = 1000, CL = 100 pF
20mV/DIV
100µs/DIV
06925-034
100µs/DIV
06925-053
2
Figure 29. Small Signal Pulse Response, G = 1000, RL = 25 kΩ, CL = 100 pF
G=5
G = 10
G = 100
SOURCING
–1
–2
+2
SINKING
+1
06925-074
OUTPUT VOLTAGE SWING (V)
REFERRED TO SUPPLY VOLTAGES
+VS
2
20mV/DIV
10µs/DIV
06925-028
–VS
0.01
0.1
1
OUTPUT CURRENT (mA)
Figure 30. Output Voltage Swing vs. Output Current
Figure 28. Small Signal Pulse Response, G = 5, 10, 100; RL = 10 kΩ
Rev. 0 | Page 13 of 20
10
AD8223
THEORY OF OPERATION
AMPLIFIER ARCHITECTURE
GAIN SELECTION
The AD8223 is an instrumentation amplifier based on a
classic 3-op amp approach, modified to ensure operation
even at common-mode voltages at the negative supply rail.
The architecture allows lower voltage offsets, better CMRR,
and higher gain accuracy than competing instrumentation
amplifiers in its class.
Placing a resistor across the RG terminals sets the gain of the
AD8223, which can be calculated by referring to Table 7 or by
using the following gain equation:
RG 
POSITIVE SUPPLY
7
1% Standard Table
Value of RG (Ω)
26.7 k
15.8 k
5.36 k
2.26 k
1.78 k
845
412
162
80.6
–
4
1
8kΩ
10kΩ
50kΩ
–
GAIN
+
8kΩ
8
10kΩ
50kΩ
7
OUT
6
REF
5
–
NONINVERTING
3
4
NEGATIVE SUPPLY
06925-038
+
Figure 31. Simplified Schematic
Figure 31 shows a simplified schematic of the AD8223. The
AD8223 has three stages. In the first stage, the input signal is
applied to PNP transistors. These PNP transistors act as voltage
buffers and allow input voltages below ground. The second
stage consists of a pair of 8 kΩ resistors, the RG resistor, and a
pair of amplifiers. This stage allows the amplification of the
AD8223 to be set with a single external resistor. The third stage
is a differential amplifier composed of an op amp, two 10 kΩ
resistors, and two 50 kΩ resistors. This stage removes the
common-mode signal and applies an additional gain of 5.
The transfer function of the AD8223 is
VOUT = G(VIN+ − VIN−) + VREF
where:
G5
80 kΩ
RG
G5
Table 7. Gains Achieved Using 1% Resistors
+
INVERTING
2
80 kΩ
Desired Gain
8
10
20
40
50
100
200
500
1000
Calculated Gain
7.99
10.1
19.9
40.4
49.9
99.7
199
499
998
The AD8223 defaults to G = 5 when no gain resistor is used. Add
the tolerance and gain drift of the RG resistor to the specifications
of the AD8223 to determine the total gain accuracy of the system.
When the gain resistor is not used, gain depends only on
internal resistor matching, so gain error and gain drift are
minimal.
INPUT VOLTAGE RANGE
The 3-op amp architecture of the AD8223 applies gain and then
removes the common-mode voltage. Therefore, internal nodes
in the AD8223 experience a combination of both the gained
signal and the common-mode signal. This combined signal can
be limited by the voltage supplies even when the individual input
and output signals are not. To determine whether the signal can be
limited, refer to Figure 18 through Figure 21. Alternatively, use
the parameters in the Specifications section to verify that the input
and output are not limited and then use the following formula to
make sure the internal nodes are not limited.
To check if it is limited by the internal nodes,
 VS  0.01 V  0.6  VCM 
VDIFF  Gain
10
  VS  0.1 V
If more common-mode range is required, a solution is to apply less
gain in the instrumentation amplifier and more in a later stage.
Rev. 0 | Page 14 of 20
AD8223
REFERENCE TERMINAL
RF INTERFERENCE (RFI)
The output voltage of the AD8223 is developed with respect to
the potential on the reference terminal. This is useful when the
output signal needs to be offset to a precise midsupply level. For
example, a voltage source can be tied to the REF pin to levelshift the output so that the AD8223 can drive a single-supply
ADC. The REF pin is protected with ESD diodes and should
not exceed either +VS or −VS by more than 0.3 V.
RF rectification is often a problem when amplifiers are used in
applications where there are strong RF signals. The disturbance
can appear as a small dc offset voltage. High frequency signals
can be filtered with a low-pass, R-C network placed at the input
of the instrumentation amplifier, as shown in Figure 34. The
filter limits the input signal bandwidth according to the following relationship:
For best performance, keep the source impedance to the REF
terminal below 5 Ω. As shown in Figure 31, the reference
terminal, REF, is at one end of a 50 kΩ resistor. Additional
impedance at the REF terminal adds to this resistor and results
in poorer CMRR performance.
INCORRECT
FilterFreqDiff 
1
2 R(2CD  CC )
FilterFreqCM 
1
2 RCC
where CD ≥ 10CC.
CORRECT
+15V
AD8223
VREF
R
+
CD
R1
47nF 499Ω
OP2177
–IN
4.02kΩ
VOUT
AD8223
R
06925-039
REF
–
CC
1nF
Figure 32. Driving the Reference Pin
10µF
0.1µF
INPUT PROTECTION
Internal supply referenced clamping diodes allow the input,
reference, output, and gain terminals of the AD8223 to safely
withstand overvoltages of 0.3 V above or below the supplies.
This is true for all gains, and for power-on and power-off. This
last case is particularly important because the signal source and
amplifier can be powered separately.
If the overvoltage is expected to exceed this value, limit the
current through these diodes to about 10 mA using external
current limiting resistors. This is shown in Figure 33. The size
of this resistor is defined by the supply voltage and the required
overvoltage protection.
+VS
1 = 10mA MAX
+
RG
AD8223
OUT
RLIM
RLIM =
–VS
Figure 34. RFI Suppression
Figure 34 shows an example in which the differential filter frequency is approximately 400 Hz, and the common-mode filter
frequency is approximately 40 kHz. The typical dc offset shift
over frequency is less than 1.5 μV, and the RF signal rejection
of the circuit is better than 71 dB.
The resistors were selected to be large enough to isolate the
circuit input from the capacitors but not large enough to
significantly increase the circuit noise. Choose values of R and
CC to minimize RFI. Mismatch between the R × CC at positive
input and the R × CC at negative input degrades the CMRR of
the AD8223. Because of their higher accuracy and stability,
COG/NPO type ceramic capacitors are recommended for the
CC capacitors. The dielectric for the CD capacitor is not as
critical.
VOVER – VS + 0.7V
10mA
06925-040
–
–15V
+
06925-041
–
VOVER
+IN
4.02kΩ
+
VOVER
+
CC
1nF
VREF
RLIM
10µF
0.1µF
AD8223
Figure 33. Input Protection
Rev. 0 | Page 15 of 20
AD8223
INCORRECT
GROUND RETURNS FOR INPUT BIAS CURRENTS
CORRECT
+VS
Input bias currents are those dc currents that must flow to bias
the input transistors of an amplifier. These are usually transistor
base currents. When amplifying floating input sources such as
transformers or ac-coupled sources, there must be a direct dc
path into each input so that the bias current can flow. Figure 35
shows how a bias current path can be provided for the cases of
transformer coupling, capacitive ac-coupling, and a thermocouple application.
+VS
AD8223
AD8223
REF
REF
–VS
–VS
TRANSFORMER
In dc-coupled resistive bridge applications, providing this path
is generally not necessary because the bias current simply flows
from the bridge supply through the bridge and into the amplifier.
However, if the impedances that the two inputs see are large and
differ by a large amount (>10 kΩ), the offset current of the input
stage causes dc errors proportional to the input offset voltage of
the amplifier.
TRANSFORMER
+VS
+VS
AD8223
AD8223
REF
REF
10MΩ
–VS
–VS
THERMOCOUPLE
THERMOCOUPLE
+VS
+VS
C
C
1
fHIGH-PASS = 2πRC
AD8223
C
REF
R
AD8223
C
REF
–VS
–VS
CAPACITIVELY COUPLED
CAPACITIVELY COUPLED
Figure 35. Creating an IBIAS Path
Rev. 0 | Page 16 of 20
06925-042
R
AD8223
APPLICATIONS INFORMATION
+VS
+VS
+2V TO +12V
0.1µF
+
10µF
0.1µF
+
RG
+
10µF
+
RG
OUTPUT
RG
–
VIN
VOUT
RG
RG
OUTPUT
RG
–
REF
REF (INPUT)
0.1µF
–VS
VOUT
REF
REF (INPUT)
10µF
+
–2V TO –12V
A. DUAL SUPPLY
06925-043
VIN
+3V TO +24V
B. SINGLE SUPPLY
Figure 36. Basic Connections
BASIC CONNECTION
OUTPUT BUFFERING
Figure 36 shows the basic connection circuit for the AD8223.
The +VS and −VS terminals are connected to the power supply.
The supply can be either bipolar (VS = ±2 V to ±12 V) or single
supply (−VS = 0 V, +VS = +3 V to +24 V). Power supplies should
be capacitively decoupled close to the power pins of the device.
For best results, use surface-mount 0.1 μF ceramic chip capacitors
and 10 μF electrolytic tantalum capacitors.
The AD8223 is designed to drive loads of 10 kΩ or greater. If
the load is less than this value, buffer the AD8223 output with a
precision single-supply op amp such as the OP113. This op amp
can swing from 0 V to 4 V on its output while driving a load as
small as 600 Ω.
5V
0.1µF
The input voltage, which can be either single-ended (tie either
−IN or +IN to ground) or differential, is amplified by the
programmed gain. The output signal appears as the voltage
difference between the output pin and the externally applied
voltage on the REF input.
5V
0.1µF
+
RG
AD8223
–
DIFFERENTIAL OUTPUT
+
Figure 38. Output Buffering
+IN
AD8223
CABLES
Receiving from a Cable
In many applications, shielded cables are used to minimize
noise; for best CMR over frequency, the shield should be
properly driven. Figure 39 shows an active guard drive that
is configured to improve ac common-mode rejection by
bootstrapping the capacitances of input cable shields, thus
minimizing the capacitance mismatch between the inputs.
+OUT
+VS
–INPUT
–IN
20kΩ
20kΩ
VREF
100Ω
AD8031
–
+
OP1177
+INPUT
RG
2
RG
2
7
1
AD8223
8
3
6
4
Figure 39. Common-Mode Shield Driver
Figure 37. Differential Output Using Op Amp
Rev. 0 | Page 17 of 20
VOUT
5
–VS
06925-044
–OUT
2
REFERENCE
06925-046
Figure 37 shows how to create a differential output in-amp. An
OP1177 op amp creates the inverted output. Because the op
amp drives the AD8223 reference pin, the AD8223 can still
ensure that the differential voltage is correct. Errors from the
op amp or mismatched resistors are common to both outputs
and are thus common mode. These common-mode errors
should be rejected by the next device in the signal chain.
REF
VOUT
OP113
–
REF
06925-045
VIN
AD8223
Driving a Cable
All cables have a certain capacitance per unit length, which
varies widely with cable type. The capacitive load from the
cable may cause peaking in the output response of the AD8223.
To reduce the peaking, use a resistor between the AD8223 and
the cable. Because cable capacitance and desired output response
vary widely, this resistor is best determined empirically. A good
starting point is 75 Ω.
The AD8232 operates at a low enough frequency that transmission
line effects are rarely an issue; therefore, the resistor need not
match the characteristic impedance of the cable.
The bridge circuit is excited by a +5 V supply. The full-scale output
voltage from the bridge (±10 mV), therefore, has a commonmode level of 2.5 V. The AD8223 removes the common-mode
component and amplifies the input signal by a factor of 100
(RG = 1.02 kΩ). This results in an output signal of ±1 V. To
prevent this signal from running into the AD8223 ground rail, the
voltage on the REF pin must be raised to at least 1 V. In this
example, the 2 V reference voltage from the AD7776 ADC is
used to bias the AD8223 output voltage to 2 V ± 1 V, which
corresponds to the input range of the ADC.
AMPLIFYING SIGNALS WITH LOW COMMONMODE VOLTAGE
Because the common-mode input range of the AD8223 extends
0.15 V below ground, it is possible to measure small differential
signals that have low, or no, common-mode components. Figure 42
shows a thermocouple application in which one side of the J-type
thermocouple is grounded.
AD8223
(DIFF OUT)
5V
0.1µF
AD8223
(SINGLE OUT)
+
06925-047
J-TYPE
THERMOCOUPLE
06925-049
5V
5V
0.1µF
0.1µF
AD7776
+
AD8223
AIN
REF
REFOUT
REFIN
06925-048
–
2V
Over a temperature range of −200°C to +200°C, the J-type
thermocouple delivers a voltage ranging from −7.890 mV
to +10.777 mV. A programmed gain on the AD8223 of 100
(RG = 845) and a voltage on the AD8223 REF pin of 2 V results
in the AD8223 output voltage ranging from 1.110 V to 3.077 V
relative to ground.
Interfacing bipolar signals to single-supply analog-to-digital
converters (ADCs) presents a challenge. The bipolar signal
must be mapped into the input range of the ADC. Figure 41
shows how this translation can be achieved.
±10mV
VOUT
REF
Figure 42. Amplifying Bipolar Signals with Low Common-Mode Voltage
A SINGLE-SUPPLY DATA ACQUISITION SYSTEM
RG
1.02kΩ
AD8223
–
Figure 40. Driving a Cable
5V
RG
1.02kΩ
Figure 41. A Single-Supply Data Acquisition System
Rev. 0 | Page 18 of 20
AD8223
OUTLINE DIMENSIONS
3.20
3.00
2.80
8
3.20
3.00
2.80
5.15
4.90
4.65
5
1
4
PIN 1
0.65 BSC
0.95
0.85
0.75
1.10 MAX
0.15
0.00
0.38
0.22
COPLANARITY
0.10
0.80
0.60
0.40
8°
0°
0.23
0.08
SEATING
PLANE
COMPLIANT TO JEDEC STANDARDS MO-187-AA
Figure 43. 8-Lead Mini Small Outline Package [MSOP]
(RM-8)
Dimensions shown in millimeters
5.00 (0.1968)
4.80 (0.1890)
8
1
5
4
1.27 (0.0500)
BSC
0.25 (0.0098)
0.10 (0.0040)
COPLANARITY
0.10
SEATING
PLANE
6.20 (0.2441)
5.80 (0.2284)
1.75 (0.0688)
1.35 (0.0532)
0.51 (0.0201)
0.31 (0.0122)
0.50 (0.0196)
0.25 (0.0099)
45°
8°
0°
0.25 (0.0098)
0.17 (0.0067)
1.27 (0.0500)
0.40 (0.0157)
COMPLIANT TO JEDEC STANDARDS MS-012-A A
CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.
Figure 44. 8-Lead Standard Small Outline Package [SOIC_N]
Narrow Body
(R-8)
Dimensions shown in millimeters and (inches)
Rev. 0 | Page 19 of 20
012407-A
4.00 (0.1574)
3.80 (0.1497)
AD8223
ORDERING GUIDE
Model
AD8223AR
AD8223AR-RL
AD8223AR-R7
AD8223ARM
AD8223ARM-RL
AD8223ARM-R7
AD8223ARMZ1
AD8223ARMZ-RL1
AD8223ARMZ-R71
AD8223ARZ1
AD8223ARZ-RL1
AD8223ARZ-R71
AD8223BR
AD8223BR-RL
AD8223BR-R7
AD8223BRM
AD8223BRM-RL
AD8223BRM-R7
AD8223BRMZ1
AD8223BRMZ-RL1
AD8223BRMZ-R71
AD8223BRZ1
AD8223BRZ-RL1
AD8223BRZ-R71
1
Temperature Range
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
Package Description
8-Lead SOIC_N
8-Lead SOIC_N,13" Tape and Reel
8-Lead SOIC_N, 7" Tape and Reel
8-Lead MSOP
8-Lead MSOP, 13" Tape and Reel
8-Lead MSOP, 7" Tape and Reel
8-Lead MSOP
8-Lead MSOP, 13" Tape and Reel
8-Lead MSOP, 7" Tape and Reel
8-Lead SOIC_N
8-Lead SOIC_N, 13" Tape and Reel
8-Lead SOIC_N, 7" Tape and Reel
8-Lead SOIC_N
8-Lead SOIC_N, 13" Tape and Reel
8-Lead SOIC_N, 7" Tape and Reel
8-Lead MSOP
8-Lead MSOP, 13" Tape and Reel
8-Lead MSOP, 7" Tape and Reel
8-Lead MSOP
8-Lead MSOP, 13" Tape and Reel
8-Lead MSOP, 7" Tape and Reel
8-Lead SOIC_N
8-Lead SOIC_N, 13" Tape and Reel
8-Lead SOIC_N, 7" Tape and Reel
Z = RoHS Compliant Part.
©2008 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D06925-0-10/08(0)
Rev. 0 | Page 20 of 20
Package Option
R-8
R-8
R-8
RM-8
RM-8
RM-8
RM-8
RM-8
RM-8
R-8
R-8
R-8
R-8
R-8
R-8
RM-8
RM-8
RM-8
RM-8
RM-8
RM-8
R-8
R-8
R-8
Branding
Y0U
Y0U
Y0U
Y0Q
Y0Q
Y0Q
Y0V
Y0V
Y0V
Y0R
Y0R
Y0R