ee Fr ad HS t e L Ro plian m Co CFS33xx Model 9x14 mm SMD, 3.3V, CMOS Frequency Range: Frequency Stability: Temperature Range: (Option M) (Option E) Storage: Input Voltage: Input Current: 1.544~34.00MHz 35.00~50.00MHz 51.00~69.00MHz 70.00~156.25 MHz Standby Current Output: Symmetry: Rise/Fall Time: 1.54~10.00 MHz 10.10~30.00 MHz 30.10~50.00 MHz 50.10~80.00 MHz 80.10~156.25 MHz Logic: 1.544MHz to 156.250MHz ±20ppm to ±100ppm 0°C to 70°C -20°C to 70°C -40°C to 85°C -55°C to 120°C 3.3V ± 0.3V Clock Oscillator With Standby Mode The CFS33xx Series utilizes fundamental and 3rd overtone crystal technology to provide a low jitter output frequency. The oscillator is equipped with power saving standby feature for battery and other low drain applications. Available on tape and reel in quantities of 500ea. 18mA Max 25mA Max 30mA Max 45mA Max 3uA Typ., 10uA Max CMOS 45/55% Max @ 50% Vdd 5ns Max @ 20/% to 80% 4ns Max @ 20/% to 80% 3ns Max @ 20/% to 80% 2.5ns Max @ 20/% to 80% 2ns Max @ 20/% to 80% "0" = 10% Vdd Max "1" = 90% Vdd Min 5ms Max 30pF Max, >80MHz 15pF Max 0.5ps Typ, 1ps Max <3ppm 1st/yr, <1ppm every year thereafter Start-up Time: Load: Jitter RMS: 12KHz~80MHz Aging: SUGGESTED PAD LAYOUT 0.560 (14.2) C P/N DC Frequency 0.360 (9.14) 0.050 (1.27) 0.040 (1.01) 0.560 (14.2) 0.210 (5.3) 1 2 0.070 (1.77) 3 4 0.200 (5.08) 0.280 (7.11) 0.200 (5.08) 0.090 (2.28) Bottom View 0.01uF Bypass Capacitor Recommended TEMPERATURE RECOMMENDED REFLOW SOLDERING PROFILE Ramp-Up 3°C/Sec Max. 260°C Crystek Part Number Guide Critical Temperature Zone Example: CFS3392-44.736MHZ Example: CFSM3392-44.736MHZ Example: CFSE3392-44.736MHZ Ramp-Down 6°C/Sec. 217°C 200°C Temperature 150°C Preheat 180 Secs. Max. 8 Minutes Max. 90 Secs. Max. 260°C for 10 Secs. Max. OUT pin 3 pin 4 Vdd PWR Supply VM Bypass Cap. pin 1 Oscillator Stopped GND or "LOW" OUT -20/ 70°C -40/ 85°C CFS3390 CFS3392 CFS3391 CFS3398 CFSM3390 CFSM3392 CFSM3391 N/A CFSE3390 CFSE3392 CFSE3391 N/A +/- 100ppm +/- 50ppm +/- 25ppm +/- 20ppm Standby Function NOTE: Reflow Profile with 240°C peak also acceptable. mA M Frequency Stability 0/ 70°C O/P Load incl Probe Cl OSC. GND pin 2 Oscillation OPEN or "HIGH" Function pin 1 Oscillator State Open "1" level .7Vdd Min "0" level 0.3Vdd Max Oscillator Active Oscillator Active Oscillator Stopped Standby Feature: When pin 1 is disabled by applying a logic "0", the output buffer of the oscillator goes into tri-state (high impedance). In addition, the internal oscillator is stopped, hence the entire oscillator consumes less than 10uA from the supply pin. Specifications subject to change without notice. TD-102703 Rev.C