AZ822 SUBMINIATURE DIP RELAY FEATURES • • • • • • • • • • Low profile for compact board spacing DC coils to 48 VDC Life expectancy to 10 million operations Standard PC 0.1" grid terminal spacing Fits standard 16 pin IC socket Minimum switching load 10 mV, 10 µA Epoxy sealed Meets FCC Part 68.302 1500 V lightning surge Meets FCC Part 68.304 1000 V dielectric UL, CUR file E43203 GENERAL DATA CONTACTS Arrangement DPDT (2 Form C) Bifurcated crossbar contacts Ratings Resistive load: Max. switched power: 60 W or 125 VA Max. switched current: 2A Max. switched voltage: 220 VDC* or 250 VAC Life Expectancy Mechanical Electrical Minimum operations 1 x 108 5 x 105 at 1 A 30 VDC (see table for additional figures) Operate Time (typical) 5 ms at nominal coil voltage Release Time (typical) 2 ms at nominal coil voltage (with no coil suppression) Capacitance Contact to contact: 1.2 pF Contact set to contact set: 1.6 pF Contact to coil: 1.5 pF Bounce (typical) At 10 mA contact current 2 ms at operate N.O. side 3 ms at operate N.C. side * Note: If switching voltage is greater than 30 VDC, special precautions must be taken. Please contact the factory. Rated Load UL, CUR 1.0 A at 24 VDC 0.5 A at 120 VAC Material Silver palladium, gold clad Resistance < 50 milliohms initially COIL Power At Pickup Voltage (typical) 74 mW 3 - 12 V coils 98 mW 15 - 24 V coils 147 mW 48 V coils Max. Continuous Dissipation 0.94 W at 20°C (68°F) Temperature Rise 15°C (27°F) at nominal coil voltage Temperature Max. 105°C (221°F) NOTES 1. All values at 20°C (68°F). 2. Relay may pull in with less than “Must Operate” value. Dielectric Strength 1000 Vrms contact to coil (at sea level for 1 min.) 1000 Vrms contact to contact 1000 Vrms between contact sets Insulation Resistance 1000 megohms min. at 20°C, 500 VDC, 50% RH Dropout Greater than 5% of nominal coil voltage Ambient Temperature Operating At nominal coil voltage -55°C (-67°F) to 90°C (194°F) Vibration 0.062" (1.5 mm) DA at 10–55 Hz Shock 20 g Enclosure P.B.T. polyester (UL94 V-0) Terminals Tinned copper alloy, P.C. Max. Solder Temp. 270°C (518°F) Max. Solder Time 5 seconds Max. Solvent Temp. 80°C (176°F) Max. Immersion Time 30 seconds 3. Relay adjustment may be affected if undue pressure is exerted on relay case. Weight 4.5 grams 4. Specifications subject to change without notice. Packing unit in pcs 20 per plastic tube / 1000 per carton box ZETTLER electronics GmbH Junkersstr. 3, D-82178 Puchheim, Germany - A ZETTLER GROUP Company phone: +49 89 800 97-0 [email protected] fax: +49 89 800 97-200 www.ZETTLERelectronics.com This product specification to be used only together with the application notes which can be downloaded from http://www.ZETTLERelectronics.com/pdfs/relais/ApplicationNotes.pdf 2014-06-17 AZ822 RELAY ORDERING DATA COIL SPECIFICATIONS Nominal Coil VDC 3 ORDER NUMBER Must Operate VDC 2.1 Max. Continuous VDC 7.5 Coil Resistance Ohm ± 10% 60 AZ822–2C–3DSE 5 3.5 12.5 167 AZ822–2C–5DSE 6 9 4.2 6.3 15.0 22.5 240 540 AZ822–2C–6DSE AZ822–2C–9DSE 12 8.4 30.0 960 AZ822–2C–12DSE 18 12.6 40.0 1,620 AZ822–2C–18DSE 24 16.8 52.9 2,880 AZ822–2C–24DSE 48 33.6 84.9 7,680 AZ822–2C–48DSE MECHANICAL DATA PC BOARD LAYOUT 8 x ø .03 [ø 0.8] .047 (1.2) REF .386 (9.8) .787 (20) .138 (3.5) 0.1 (2.54) .015 (0.38) .472 (12) .044 (1.11) Viewed toward terminals .020 (0.5) .200 (5.08) .300 (7.62) .047 (1.2) REF WIRING DIAGRAM .010 (0.25) .300 (7.62) .200 (5.08) 1 4 6 8 16 13 11 9 Viewed toward terminals Dimensions in inches with metric equivalents in parentheses. Tolerance: ± .010" TYPICAL CONTACT LIFE EXPECTANCY Maximum Switching Capacity NUMBER OF OPERATIONS VOLTAGE CURRENT RESISTIVE LOAD 1x 107 10.0 9.0 8.0 7.0 6.0 5.0 4.0 INDUCTIVE LOAD 1 x 107 50 mV 1 mA 30 VDC 1A 5 x 105 15 x 104 30 VDC 0.7 A 1 x 106 3 x 105 30 VDC 0.3 A 3 x 106 1 x 106 60 VDC 0.5 A 5 x 105 — 60 VDC 0.3 A 1 x 106 — 60 VDC 0.2 A 106 — .3 30 VAC 2A 5 x 105 15 x 104 .2 30 VAC 1.3 A 1 x 106 3 x 105 30 VAC 0.7 A 3 x 106 1 x 106 60 VAC 1A 5 x 105 15 x 104 60 VAC 0.7 A 1x 106 3 x 105 60 VAC 0.3 A 3 x 106 1 x 106 125 VAC 0.5 A 5 x 105 15 x 104 125 VAC 0.3 A 1 x 106 3 x 105 125 VAC 0.2 A 3 x 106 1 x 106 3.0 CURRENT 1.0 .9 .8 .7 .6 .5 1000 400 500 600 700 800 900 300 200 100 50 60 70 80 90 40 20 .1 30 DC resistive .4 Contact Voltage (V) NOTES: 1. Relays operated at nominal coil voltage. 2. Inductive load tests are at 0.7 power factor. 3. Table represents typical life figures and are not guaranteed minimums. ZETTLER electronics GmbH Junkersstr. 3, D-82178 Puchheim, Germany AC resistive 10 3x 2.0 - A ZETTLER GROUP Company phone: +49 89 800 97-0 [email protected] fax: +49 89 800 97-200 www.ZETTLERelectronics.com This product specification to be used only together with the application notes which can be downloaded from http://www.ZETTLERelectronics.com/pdfs/relais/ApplicationNotes.pdf 2014-06-17