SOLID TANTALUM ELECTROLYTIC CAPACITORS MUSE F95 Conformal coated Chip, For Mobile Audio Specifications Adapted to the RoHS directive (2002/95/EC). Item Per formance Characteristics Category --55 ~ +125˚C (Rated temperature : +85˚C) Temperature Range Capacitance Tolerance ± 20% (at 120Hz) Dissipation Factor Refer to next page (at 120Hz) ESR(100kHz) Refer to next page Leakage Current • After 1 minute's application of rated voltage, leakage current at 25˚C is not more than 0.01CV or 0.5 µA, whichever is greater. +15% Max. (at +125˚C) +10% Max. (at + 85˚C) --10% Max. (at --55˚C) At 40˚C, 90 ~ 95% R.H., For 500 hours (No voltage applied) Capacitance Change • • • • • • Refer to next page (∗1) Damp Heat Dissipation Factor • • • • • • • • • • Initial specified value or less Leakage Current • • • • • • • • • • • • Initial specified value or less At --55˚C / +125˚C, 30 minutes each, For 5 cycles, Capacitance Change • • • • • • Refer to next page (∗1) Temperature Cycles Dissipation Factor • • • • • • • • • • Initial specified value or less Leakage Current • • • • • • • • • • •• Initial specified value or less Capacitance Change by Temperature Applications Mobile Audio Player Digital video camcorder Reflow at 260˚C for 10 seconds Resistance to Soldering Heat Digital still camera Mobile phone Feature Rich sound in the bass register and clear sound,Materials are strictly selected to achieve high level sound. F95 series has no lead-frame, and no vibration factor. Low ESR, Low ESL Line up miniature size and high capacitance, necessary to mobile design. Surge∗ After application of surge voltage in series with a 33Ω resistor at the rate of 30 seconds ON, 30 seconds OFF, for 1000 successive test cycles at 85˚C, capacitors meet the characteristics requirements listed below. Capacitance Change • • • • • • Refer to next page (∗1) Dissipation Factor • • • • • • • • • • Initial specified value or less Leakage Current • • • • • • • • • • • • Initial specified value or less Endurance∗ After 2000 hours' application of rated voltage at 85˚C, or derated voltage at 125˚C, capacitors meet the characteristic requirements listed below. Capacitance Change • • • • • • Refer to next page (∗1) Dissipation Factor • • • • • • • • • • Initial specified value or less Leakage Current • • • • • • • • • • •• Initial specified value or less Type numbering system (Example : 4V 220 µF) Shear Test 1 2 3 F 9 5 4 5 6 7 8 9 10 11 0 G 2 2 7 M A 12 13 14 15 16 A M 1 Q 2 Single face electrode MUSE series code Terminal Strength Case code Capacitance tolerance Rated Capacitance After applying the pressure load of 5N for 10 ± 1 seconds horizontally to the center of capacitor side body which has no electrode and has been soldered 5N (0.51kg • f) beforehand on an aluminum substrate, For 10 ± 1 seconds there shall be found neither exfoliation nor its sign at the terminal electrode. Keeping a capacitor surface-mounted on a substrate upside down and supporting the substrate at both of the opposite bottom points 45mm apart from the center of the capacitor, the pressure strength is applied with 20 R230 a specified jig at the center of the substrate so that the substrate may bend by 1mm as illustrated. Then, there shall be found no remarkable 45 45 abnormality on the capacitor terminals. 1mm Taping code (Refer to page 267 for details) Capacitance Change • • • • • • • • • Refer to next page (∗1) Dissipation Factor • • • • • • • • • • • • • Initial specified value or less Leakage Current • • • • • • • • • • •• • • • Initial specified value or less ∗ As for the surge and derated voltage at 125˚C, refer to page 266 for details. Rated voltage Series Dimensions Drawing L W H Resin case code S A T B L 3.2 ± 0.3 3.2 ± 0.3 3.5 ± 0.2 3.5 ± 0.2 (mm) W 1.6 ± 0.3 1.7 ± 0.3 2.7 ± 0.2 2.8 ± 0.2 H 1.0 ± 0.2 1.4 ± 0.2 1.0 ± 0.2 1.8 ± 0.2 A 0.8 ± 0.3 0.8 ± 0.3 0.8 ± 0.2 0.8 ± 0.3 B 1.2 ± 0.3 1.2 ± 0.3 1.2 ± 0.2 1.2 ± 0.3 C 0.8 ± 0.3 0.8 ± 0.3 1.1 ± 0.2 1.1 ± 0.3 (D) (0.2) (0.2) (0.2) (0.2) D dimension only for reference Solder electrode Solder electrode A B C (D) Single-side electrodes (Both electrodes at bottom side only) CAT.8100V SOLID TANTALUM ELECTROLYTIC CAPACITORS MUSE F95 Standard ratings Cap. (µF) Marking 4 6.3 10 Code 0G 0J 1A V 68 686 S S•A B 100 107 S S•A•T B 150 157 S (A) 220 227 S•A•T ( T) • B (B) 330 337 T•B 470 477 (B) 680 687 (B) S•A case T•B Case J8 J8 Rating (capacitance) code µF code 68 W7 100 A8 150 E8 220 J8 330 N8 470 S8 680 W8 ( ) The series in parentheses are being developed. Please contact to your local Nichicon sales office when these series are being designed in your application. Standard ratings Rated Rated Volt Capacitance (µF) 4V 6.3V 10V Case code Part Number *1 Leakage Disspation ESR ∆C/C Factor Current (µA) (%@120Hz) (Ω@100kHz) (%) ∗ 68 S F950G686MSAAM1Q2 2.7 10 0.8 100 S F950G107MSAAM1Q2 4.0 14 0.8 ∗ 150 S F950G157MSAAM1Q2 6.0 22 0.8 ± 15 220 S F950G227MSAAM1Q2 8.8 25 0.8 ± 15 220 A F950G227MAAAM1Q2 8.8 25 0.8 ± 15 220 T F950G227MTAAM1Q2 8.8 25 0.6 ∗ 330 T F950G337MTAAM1Q2 13.2 40 0.8 ± 20 330 B F950G337MBAAM1Q2 13.2 30 0.5 ± 15 68 S F950J686MSAAM1Q2 4.3 14 0.9 ∗ 68 A F950J686MAAAM1Q2 4.3 12 0.5 ∗ 100 S F950J107MSAAM1Q2 6.3 20 0.9 ± 15 100 A F950J107MAAAM1Q2 6.3 14 0.5 ∗ 100 T F950J107MTAAM1Q2 6.3 14 0.6 ∗ 220 B F950J227MBAAM1Q2 13.9 30 0.4 ∗ 68 B F951A686MBAAM1Q2 6.8 12 0.4 ∗ 100 B F951A107MBAAM1Q2 10.0 14 0.4 ∗ *1 : ∆C/C Item Damp Heat Tempereature cycles Resistance soldering heat Surge Endurance S • A • T • B Case (%) ±10 ±5 ±5 ±5 ±10 CAT.8100V