AD EVAL-ADMP401Z-FLEX Omnidirectional microphone with bottom port and analog output Datasheet

FEATURES
FUNCTIONAL BLOCK DIAGRAM
4.72 mm × 3.76 mm × 1.0 mm surface-mount package
High SNR of 62 dBA
Sensitivity of −42 dBV
Flat frequency response from 100 Hz to 15 kHz
Low current consumption of <250 μA
Single-ended analog output
High PSR of 70 dB
Compatible with Sn/Pb and Pb-free solder processes
RoHS/WEEE compliant
OUTPUT
AMPLIFIER
ADMP401
OUTPUT
POWER
VDD GND
07712-001
Data Sheet
Omnidirectional Microphone with
Bottom Port and Analog Output
ADMP401
Figure 1.
APPLICATIONS
Smartphones and feature phones
Teleconferencing systems
Digital video cameras
Bluetooth headsets
Video phones
Tablets
GENERAL DESCRIPTION
The ADMP4011 is a high quality, high performance, low power,
analog output, bottom-ported omnidirectional MEMS
microphone. The ADMP401 consists of a MEMS microphone
element, an impedance converter, and an output amplifier. The
ADMP401 sensitivity specification makes it an excellent choice
for both near field and far field applications. The ADMP401 has
a high SNR and flat wideband frequency response, resulting in
natural sound with high intelligibility. Low current consumption
1
enables long battery life for portable applications. The ADMP401
complies with the TIA-920 standard, Telecommunications
Telephone Terminal Equipment Transmission Requirements for
Wideband Digital Wireline Telephones.
The ADMP401 is available in a thin, 4.72 mm × 3.76 mm ×
1.0 mm surface-mount package. It is reflow solder compatible
with no sensitivity degradation. The ADMP401 is halide free.
Protected by U.S. Patents 7,449,356; 7,825,484; 7,885,423; 7,961,897. Other patents are pending.
Rev. E
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113 ©2010–2012 Analog Devices, Inc. All rights reserved.
Powered by TCPDF (www.tcpdf.org)
IMPORTANT LINKS for the ADMP401*
Last content update 09/20/2013 09:49 pm
DOCUMENTATION
PARAMETRIC SELECTION TABLES
AN-1181: Using a MEMS Microphone in a 2-Wire Microphone Circuit
AN-1165: Op Amps for MEMS Microphone Preamp Circuits
AN-1140: Microphone Array Beamforming
AN-1124: Recommendations for Sealing Analog Devices, Inc., BottomPort MEMS Microphones from Dust and Liquid Ingress
AN-1112: Microphone Specifications Explained
AN-1068: Reflow Soldering of the MEMS Microphone
AN-1003: Recommendations for Mounting and Connecting Analog
Devices, Inc., Bottom-Ported MEMS Microphones
Introducing iMEMS(R) Microphones This video compares the ADMP401
Analog MEMS and the ADMP421 Digital MEMS with a BK Type 4939
Measurement microphone.
UG-278: EVAL-ADMP401Z-FLEX: Bottom-Ported Analog Output MEMS
Microphone Evaluation Board
UG-126: EVAL-ADMP401Z Bottom-Ported Analog Output MEMS
Microphone Evaluation Board
MS-2472: Analog and Digital MEMS Microphone Design
Considerations
MS-2275: Common Inter-IC Digital Interfaces for Audio Data Transfer
A History of Consumer Microphones:
Industrial ICs Solutions Bulletin, Volume 10, Issue 8
Industrial ICs
Find Similar Products By Operating Parameters
Consider ADMP404: Omnidirectional Microphone with Bottom Port
and Analog Output
Consider ADMP405: Omnidirectional Microphone with Bottom Port
and Analog Output
Consider ADMP421: Omnidirectional Microphone with Bottom Port
and Analog Output
Consider ADMP441: Omnidirectional Microphone with Bottom Port
and Analog Output
Consider ADMP504: Omnidirectional Microphone with Bottom Port
and Analog Output
Consider ADMP521: Omnidirectional Microphone with Bottom Port
and Analog Output
DESIGN TOOLS, MODELS, DRIVERS & SOFTWARE
Microphone Beamforming Simulation Tool (32-bit)
- Documentation for the microphone beamforming simulator
Microphone Beamforming Simulation Tool (64-bit)
- Documentation for the microphone beamforming simulator
PRODUCT RECOMMENDATIONS & REFERENCE DESIGNS
CN-0262: Low Noise Analog MEMS Microphone and Preamp with
Compression and Noise Gating
CN-0207: High Performance Analog MEMS Microphone's Simple
Interface to SigmaDSP Audio Codec
EVALUATION KITS & SYMBOLS & FOOTPRINTS
MEMS Microphone Evaluation Boards
ADMP401Z Evaluation Board
ADMP401 Flex Evaluation Board
Symbols and Footprints
DESIGN COLLABORATION COMMUNITY
Collaborate Online with the ADI support team and other designers
about select ADI products.
Follow us on Twitter: www.twitter.com/ADI_News
Like us on Facebook: www.facebook.com/AnalogDevicesInc
DESIGN SUPPORT
Submit your support request here:
Linear and Data Converters
Embedded Processing and DSP
Telephone our Customer Interaction Centers toll free:
Americas:
Europe:
China:
India:
Russia:
1-800-262-5643
00800-266-822-82
4006-100-006
1800-419-0108
8-800-555-45-90
Quality and Reliability
Lead(Pb)-Free Data
SAMPLE & BUY
ADMP401
View Price & Packaging
Request Evaluation Board
Request Samples
Check Inventory & Purchase
Find Local Distributors
* This page was dynamically generated by Analog Devices, Inc. and inserted into this data sheet.
Note: Dynamic changes to the content on this page (labeled 'Important Links') does not
constitute a change to the revision number of the product data sheet.
This content may be frequently modified.
ADMP401
Data Sheet
TABLE OF CONTENTS
Features .............................................................................................. 1
Connecting the ADMP401 to a Codec ......................................8
Applications ....................................................................................... 1
Connecting the ADMP401 to an Op Amp Gain Stage ............8
Functional Block Diagram .............................................................. 1
Supporting Documents ................................................................8
General Description ......................................................................... 1
Handling Instructions .......................................................................9
Revision History ............................................................................... 2
Pick-and-Place Equipment ..........................................................9
Specifications..................................................................................... 3
Reflow Solder .................................................................................9
Absolute Maximum Ratings ............................................................ 4
Board Wash ....................................................................................9
ESD Caution .................................................................................. 4
Reliability Specifications ................................................................ 10
Pin Configuration and Function Descriptions ............................. 5
Outline Dimensions ....................................................................... 11
Printed Circuit Board (PCB) Land Pattern Layout ...................... 6
Ordering Guide .......................................................................... 11
Typical Performance Characteristics ............................................. 7
Applications Information ................................................................ 8
REVISION HISTORY
7/12—Rev. D to Rev. E
Changes to Features Section, General Description Section, and
Page 1 Layout .................................................................................... 1
Add Note 1......................................................................................... 1
Changes to Frequency Response Parameter, Table 1 and Powers
Supply Rejection Parameter, Table 1 .............................................. 3
Changes to Temperature Range Parameter, Table 2..................... 4
Changes to Figure 6, Figure 7, and Figure 8.................................. 7
Changes to Applications Information Section and Figure 10..... 8
Added Supporting Documents Section, Application Notes
Section, Circuit Notes Section, and Evaluation Board User
Guides Section .................................................................................. 8
Changes to THB Description Column, Table 5 and Temperature
Cycle Column, Table 5 ................................................................... 10
Changes to Ordering Guide .......................................................... 11
1/12—Rev. C to Rev. D
Updated Outline Dimensions ....................................................... 11
Changes to Figure 12 ...................................................................... 11
Added Figure 13.............................................................................. 11
Change to Ordering Guide ............................................................ 11
8/11—Rev. B to Rev. C
Changes to Figure 1 ...........................................................................1
Changes to Table 3.............................................................................4
Removed Terminal Side Down from Figure 3 ...............................5
Changes to Bullet 2 in Pick-and-Place Equipment Section .........9
Changes to Ordering Guide .......................................................... 11
12/10—Rev. A to Rev. B
Changes to Applications and General Description Sections .......1
Changes to Table 1.............................................................................3
8/10—Rev. 0 to Rev. A
Changes to Frequency Response Parameter, Table 1 ....................3
Changes to Supply Voltage Parameter, Table 2 ..............................4
Changes to Applications Information Section, Figure 9, and
Figure 10 .............................................................................................8
Updated Outline Dimensions ....................................................... 11
4/10—Revision 0: Initial Version
Rev. E | Page 2 of 12
Data Sheet
ADMP401
SPECIFICATIONS
TA = 25°C, VDD = 1.8 V, unless otherwise noted. All minimum and maximum specifications are guaranteed. Typical specifications are not
guaranteed.
Table 1.
Parameter
PERFORMANCE
Directionality
Sensitivity
Signal-to-Noise Ratio
Equivalent Input Noise
Dynamic Range
Frequency Response 1
Symbol
Total Harmonic Distortion
Power Supply Rejection
Maximum Acoustic Input
POWER SUPPLY
Supply Voltage
Supply Current
OUTPUT CHARACTERISTICS
Output Impedance
Output DC Offset
Output Current Limit
THD
PSR
1
Test Conditions/Comments
Min
1 kHz, 94 dB SPL
−45
SNR
EIN
Derived from EIN and maximum acoustic input
Low frequency, −3 dB point
High frequency, −3 dB point
Deviation limits from flat response within pass band
105 dB SPL
217 Hz, 100 mV p-p square wave superimposed on VDD = 1.8 V
Peak
VDD
IS
Typ
Omni
−42
62
32
88
60
15
−3/+2
Rev. E | Page 3 of 12
−39
dBV
dBA
dBA SPL
dB
Hz
kHz
dB
%
dB
dB SPL
3
3.3
250
200
0.8
90
See Figure 6 and Figure 7.
Unit
70
120
1.5
ZOUT
Max
V
µA
Ω
V
µA
ADMP401
Data Sheet
ABSOLUTE MAXIMUM RATINGS
ESD CAUTION
Table 2.
Parameter
Supply Voltage
Sound Pressure Level (SPL)
Mechanical Shock
Vibration
Temperature Range
Rating
−0.3 V to +3.6 V
160 dB
10,000 g
Per MIL-STD-883 Method 2007,
Test Condition B
−40°C to +85°C
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
CRITICAL ZONE
TL TO TP
tP
TP
tL
TSMAX
TSMIN
tS
RAMP-DOWN
PREHEAT
07712-002
TEMPERATURE
RAMP-UP
TL
t25°C TO PEAK
TIME
Figure 2. Recommended Soldering Profile Limits
Table 3. Recommended Soldering Profile Limits
Profile Feature
Average Ramp Rate (TL to TP)
Preheat
Minimum Temperature (TSMIN)
Maximum Temperature (TSMAX)
Time (TSMIN to TSMAX), tS
Ramp-Up Rate (TSMAX to TL)
Time Maintained Above Liquidous (tL)
Liquidous Temperature (TL)
Peak Temperature (TP)
Time Within 5°C of Actual Peak Temperature (tP)
Ramp-Down Rate
Time 25°C (t25°C) to Peak Temperature
Rev. E | Page 4 of 12
Sn-Pb
1.25°C/sec maximum
Pb Free
1.25°C/sec maximum
100°C
150°C
60 sec to 75 sec
1.25°C/sec
45 sec to 75 sec
183°C
215°C +3°C/−3°C
20 sec to 30 sec
3°C/sec maximum
5 min maximum
100°C
200°C
60 sec to 75 sec
1.25°C/sec
~50 sec
217°C
245°C +0°C/−5°C
20 sec to 30 sec
3°C/sec maximum
5 min maximum
Data Sheet
ADMP401
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
OUTPUT
GND
2
1
GND
3
GND
6
VDD
4
5
BOTTOM VIEW
Not to Scale
07712-003
GND
Figure 3. Pin Configuration (Bottom View)
Table 4. Pin Function Descriptions
Pin No.
1
2
3
4
5
6
Mnemonic
OUTPUT
GND
GND
GND
VDD
GND
Description
Analog Output Signal
Ground
Ground
Ground
Power Supply
Ground
Rev. E | Page 5 of 12
ADMP401
Data Sheet
PRINTED CIRCUIT BOARD (PCB) LAND PATTERN LAYOUT
A suggested solder paste stencil pattern layout is shown in
Figure 5. The diameter of the sound hole in the PCB should be
larger than the diameter of the sound port of the microphone.
A minimum diameter of 0.5 mm is recommended.
The recommended PCB land pattern for the ADMP401 should
have a 1:1 ratio to the solder pads on the microphone package,
as shown in Figure 4. Take care to avoid applying solder paste to
the sound hole in the PCB.
2.62
ø0.90 (3×)
ø1.10
ø1.68
2.54
2.40
1.20
1.27
07712-004
ø0.70 (2×)
0.79
Figure 4. PCB Land Pattern Layout (Dimensions Shown in mm)
1.8mm/1.3mm DIA. 0.2032 CUT WIDTH (4×)
0.649mm DIA. (2×)
0.85mm DIA. (3×)
2.4mm
2.54mm
1.2mm
2.62mm
3.41mm
Figure 5. Suggested Solder Paste Stencil Pattern Layout
Rev. E | Page 6 of 12
07712-005
1.27mm
Data Sheet
ADMP401
TYPICAL PERFORMANCE CHARACTERISTICS
0
10
8
–10
6
–30
2
PSR (dB)
SENSITIVITY (dB)
–20
4
0
–2
–40
–50
–4
–60
–6
100
10k
1k
FREQUENCY (Hz)
–80
100
07712-006
–10
50
Figure 6. Frequency Response Mask
Figure 8. Typical Power Supply Rejection vs. Frequency
0
–10
100
1k
10k
FREQUENCY (Hz)
07712-007
AMPLITUDE (dB)
10
–20
10
1k
FREQUENCY (Hz)
Figure 7. Typical Frequency Response (Measured)
Rev. E | Page 7 of 12
10k
07712-008
–70
–8
ADMP401
Data Sheet
APPLICATIONS INFORMATION
CONNECTING THE ADMP401 TO AN OP AMP
GAIN STAGE
GAIN = (R1 + R2)/R1
0.1µF
R1
VDD
ADMP401
R2
VREF
1µF
MINIMUM
VO
OUTPUT
10kΩ
fC = 1/(2π × C × R)
ADA4897-1
GND
VREF
where R is the input impedance of the codec.
A minimum value of 2.2 µF is recommended in Figure 9
because the input impedance of the ADAU1361/ADAU1761
can be as low as 2 kΩ at its highest PGA gain setting, which
results in a high-pass filter corner frequency at about 37 Hz.
Figure 10 shows the ADMP401 connected to the ADA4897-1
op amp configured as a noninverting preamplifier.
CONNECTING THE ADMP401 TO A CODEC
07712-010
The ADMP401 output can be connected to a dedicated codec
microphone input (see Figure 9) or to a high input impedance
gain stage (see Figure 10). A 0.1 µF ceramic capacitor placed
close to the ADMP401 supply pin is used for testing and is
recommended to adequately decouple the microphone from
noise on the power supply. A dc-blocking capacitor is required
at the output of the microphone. This capacitor creates a highpass filter with a corner frequency at
Figure 10. ADMP401 Connected to the ADA4897-1 Op Amp
SUPPORTING DOCUMENTS
Application Notes
AN-1003, Recommendations for Mounting and Connecting
Analog Devices, Inc., Bottom-Ported MEMS Microphones
AN-1068, Reflow Soldering of the MEMS Microphone
AN-1112, Microphone Specifications Explained
MICBIAS
AN-1124, Recommendations for Sealing Analog Devices, Inc.,
Bottom-Port MEMS Microphones from Dust and Liquid
Ingress
0.1µF
ADAU1761
VDD
ADMP401
OUTPUT
OR
2.2µF
MINIMUM
ADAU1361
AN-1140, Microphone Array Beamforming
LINN
Circuit Notes
GND
CM
07712-009
LINP
Figure 9. ADMP401 Connected to the Analog Devices ADAU1761 or
ADAU1361 Codec
CN-0207, High Performance Analog MEMS Microphone’s Simple
Interface to SigmaDSP Audio Codec
CN-0262, Low Noise Analog MEMS Microphone and Preamp
with Compression and Noise Gating
Evaluation Board User Guides
UG-126, EVAL-ADMP401Z: Bottom-Ported Analog Output MEMS
Microphone Evaluation Board
UG-278, EVAL-ADMP401Z-FLEX: Bottom-Ported Analog
Output MEMS Microphone Evaluation Board
Rev. E | Page 8 of 12
Data Sheet
ADMP401
HANDLING INSTRUCTIONS
PICK-AND-PLACE EQUIPMENT
REFLOW SOLDER
The MEMS microphone can be handled using standard pickand-place and chip shooting equipment. Care should be taken
to avoid damage to the MEMS microphone structure as follows:
For best results, the soldering profile should be in accordance
with the recommendations of the manufacturer of the solder
paste that is used to attach the MEMS microphone to the PCB.
It is recommended that the solder reflow profile not exceed the
limit conditions specified in Figure 2 and Table 3.
•
•
•
•
•
Use a standard pickup tool to handle the microphone.
Because the microphone hole is on the bottom of the
package, the pickup tool can make contact with any part
of the lid surface.
Use care during pick-and-place to ensure that no high
shock events above 10 kg are experienced because such
events may cause damage to the microphone.
Do not pick up the microphone with a vacuum tool that
makes contact with the bottom side of the microphone.
Do not pull air out or blow air into the microphone port.
Do not use excessive force to place the microphone on
the PCB.
BOARD WASH
When washing the PCB, ensure that water does not make
contact with the microphone port. Blow-off procedures and
ultrasonic cleaning must not be used.
Rev. E | Page 9 of 12
ADMP401
Data Sheet
RELIABILITY SPECIFICATIONS
The microphone sensitivity after stress must deviate by no more than ±3 dB from the initial value.
Table 5.
Stress Test
Low Temperature Operating Life
High Temperature Operating Life
THB
Temperature Cycle
High Temperature Storage
Low Temperature Storage
Component CDM ESD
Component HBM ESD
Component MM ESD
Description
−40°C, 500 hours, powered
+125°C, 500 hours, powered
+85°C/85% relative humidity, 500 hours, powered
−40°C/+125°C, one cycle per hour, 1000 cycles
+150°C, 500 hours
−40°C, 500 hours
All pins, 0.5 kV
All pins, 1.5 kV
All pins, 0.2 kV
Rev. E | Page 10 of 12
Data Sheet
ADMP401
OUTLINE DIMENSIONS
4.82
4.72
4.62
3.30 REF
REFERENCE
CORNER
4.10 REF
PIN 1
3.86
3.76
3.66
2.40 BSC
3.14
REF
1
2
1.68 DIA.
3
1.10 DIA.
6
4
5
0.68 REF
2.54
BSC
1.27 BSC
0.25 DIA.
(THRU HOLE)
1.20 BSC
TOP VIEW
1.10
1.00
0.90
0.79 BSC
2.62 BSC
0.90 DIA.
(PINS 1, 5, 6)
0.61 REF
0.70 DIA.
(PINS 2, 4)
BOTTOM VIEW
SIDE VIEW
12-12-2011-C
0.73 REF
0.24 REF
Figure 11. 6-Terminal Chip Array Small Outline No Lead Cavity [LGA_CAV]
4.72 mm × 3.76 mm Body
(CE-6-1)
Dimensions shown in millimeters
DIRECTION OF FEED
07712-011
PIN 1
Figure 12. Microphone Orientation in Tape Until Date Code 1213
DIRECTION OF FEED
07712-012
PIN 1
Figure 13. Microphone Orientation in Tape Starting with Date Code 1213
ORDERING GUIDE
Model 1
ADMP401ACEZ-RL
ADMP401ACEZ-RL7
EVAL-ADMP401Z
EVAL-ADMP401Z-FLEX
1
2
Temperature Range
−40°C to +85°C
−40°C to +85°C
Package Description
6-Terminal LGA_CAV, 13” Tape and Reel
6-Terminal LGA_CAV, 7” Tape and Reel
Evaluation Board
Evaluation Board
Z = RoHS Compliant Part.
The CE-6-1 package option is halide free.
Rev. E | Page 11 of 12
Package Option 2
CE-6-1
CE-6-1
Ordering Quantity
4,500
1,000
ADMP401
Data Sheet
NOTES
©2010–2012 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D07712-0-7/12(E)
Rev. E | Page 12 of 12
Similar pages