CY7C1354C, CY7C1356C 9-Mbit (256 K × 36/512 K × 18) Pipelined SRAM with NoBL™ Architecture 9-Mbit (256 K × 36/512 K × 18) Pipelined SRAM with NoBL™ Architecture Features Functional Description ■ Pin-compatible and functionally equivalent to ZBT ■ Supports 250 MHz bus operations with zero wait states ❐ Available speed grades are 250, 200, and 166 MHz ■ Internally self-timed output buffer control to eliminate the need to use asynchronous OE ■ Fully registered (inputs and outputs) for pipelined operation ■ Byte write capability ■ Single 3.3 V power supply (VDD) ■ 3.3 V or 2.5 V I/O power supply (VDDQ) ■ Fast clock-to-output times ❐ 2.8 ns (for 250 MHz device) ■ Clock enable (CEN) pin to suspend operation ■ Synchronous self-timed writes ■ Available in Pb-free 100-pin TQFP package, Pb-free, and non Pb-free 119-ball BGA package and 165-ball FBGA package The CY7C1354C and CY7C1356C[1] are 3.3 V, 256 K x 36 and 512K x 18 synchronous pipelined burst SRAMs with No Bus Latency™ (NoBL logic, respectively. They are designed to support unlimited true back-to-back read/write operations with no wait states. The CY7C1354C and CY7C1356C are equipped with the advanced (NoBL) logic required to enable consecutive read/write operations with data being transferred on every clock cycle. This feature greatly improves the throughput of data in systems that require frequent write/read transitions. The CY7C1354C and CY7C1356C are pin compatible and functionally equivalent to ZBT devices. All synchronous inputs pass through input registers controlled by the rising edge of the clock. All data outputs pass through output registers controlled by the rising edge of the clock. The clock input is qualified by the clock enable (CEN) signal, which when deasserted suspends operation and extends the previous clock cycle. ■ IEEE 1149.1 JTAG-compatible boundary scan ■ Burst capability – linear or interleaved burst order ■ “ZZ” sleep mode option and stop clock option Write operations are controlled by the byte write selects (BWa–BWd for CY7C1354C and BWa–BWb for CY7C1356C) and a write enable (WE) input. All writes are conducted with on-chip synchronous self-timed write circuitry. Three synchronous chip enables (CE1, CE2, CE3) and an asynchronous output enable (OE) provide for easy bank selection and output tristate control. To avoid bus contention, the output drivers are synchronously tristated during the data portion of a write sequence. Logic Block Diagram – CY7C1354C (256 K × 36) ADDRESS REGISTER 0 A0, A1, A A1 A1' D1 Q1 A0 A0' BURST D0 Q0 LOGIC MODE CLK CEN ADV/LD C C WRITE ADDRESS REGISTER 1 WRITE ADDRESS REGISTER 2 S E N S E ADV/LD WRITE REGISTRY AND DATA COHERENCY CONTROL LOGIC BW a BW b BW c BW d WRITE DRIVERS MEMORY ARRAY A M P S WE O U T P U T R E G I S T E R S E INPUT REGISTER 1 OE CE1 CE2 CE3 E O U T P U T D A T A S T E E R I N G INPUT REGISTER 0 B U F F E R S DQ s DQ Pa DQ Pb DQ Pc DQ Pd E E READ LOGIC SLEEP CONTROL ZZ Note 1. For best-practices recommendations, refer to the Cypress application note System Design Guidelines on www.cypress.com. Cypress Semiconductor Corporation Document Number: 38-05538 Rev. *K • 198 Champion Court • San Jose, CA 95134-1709 • 408-943-2600 Revised March 2, 2011 [+] Feedback CY7C1354C, CY7C1356C Logic Block Diagram – CY7C1356C (512 K × 18) A0, A1, A ADDRESS REGISTER 0 A1 A1' D1 Q1 A0 A0' BURST D0 Q0 LOGIC MODE CLK CEN ADV/LD C C WRITE ADDRESS REGISTER 1 WRITE ADDRESS REGISTER 2 S E N S E ADV/LD BW a WRITE REGISTRY AND DATA COHERENCY CONTROL LOGIC WRITE DRIVERS MEMORY ARRAY A M P S BW b WE O U T P U T R E G I S T E R S O U T P U T D A T A B U F F E R S S T E E R I N G E INPUT REGISTER 1 OE CE1 CE2 CE3 ZZ Document Number: 38-05538 Rev. *K E DQ s DQ Pa DQ Pb E INPUT REGISTER 0 E READ LOGIC Sleep Control Page 2 of 32 [+] Feedback CY7C1354C, CY7C1356C Contents Selection Guide ................................................................ 4 Pin Configurations ........................................................... 4 Pin Definitions .................................................................. 7 Functional Overview ........................................................ 8 Single Read Accesses ................................................ 8 Burst Read Accesses .................................................. 8 Single Write Accesses ................................................. 8 Burst Write Accesses .................................................. 9 Sleep Mode ................................................................. 9 Partial Write Cycle Description ..................................... 10 Truth Table ...................................................................... 10 Partial Write Cycle Description ..................................... 11 IEEE 1149.1 Serial Boundary Scan (JTAG) .................. 12 Disabling the JTAG Feature ...................................... 12 TAP Controller State Diagram ....................................... 12 Test Access Port (TAP) ............................................. 12 TAP Controller Block Diagram ...................................... 12 PERFORMING A TAP RESET .................................. 12 TAP REGISTERS ...................................................... 13 TAP Instruction Set ................................................... 13 TAP Timing ...................................................................... 14 TAP AC Switching Characteristics ............................... 14 3.3 V TAP AC Test Conditions ....................................... 15 3.3 V TAP AC Output Load Equivalent ......................... 15 2.5 V TAP AC Test Conditions ....................................... 15 2.5 V TAP AC Output Load Equivalent ......................... 15 Document Number: 38-05538 Rev. *K TAP DC Electrical Characteristics and Operating Conditions ............................................. 15 Identification Register Definitions ................................ 15 Scan Register Sizes ....................................................... 16 Identification Codes ....................................................... 16 Boundary Scan Exit Order (256 K × 36) ........................ 17 Boundary Scan Exit Order (512 K × 18) ........................ 18 Maximum Ratings ........................................................... 19 Operating Range ............................................................. 19 Neutron Soft Error Immunity ......................................... 19 Electrical Characteristics ............................................... 19 Capacitance .................................................................... 20 Thermal Resistance ........................................................ 20 Switching Characteristics .............................................. 22 Switching Waveforms .................................................... 23 Ordering Information ...................................................... 26 Ordering Code Definitions ......................................... 26 Package Diagrams .......................................................... 27 Acronyms ........................................................................ 30 Document Conventions ................................................. 30 Units of Measure ....................................................... 30 Document History Page ................................................. 31 Sales, Solutions, and Legal Information ...................... 32 Worldwide Sales and Design Support ....................... 32 Products .................................................................... 32 PSoC Solutions ......................................................... 32 Page 3 of 32 [+] Feedback CY7C1354C, CY7C1356C Selection Guide Description Maximum access time Maximum operating current Maximum CMOS standby current 250 MHz 2.8 250 40 200 MHz 3.2 220 40 166 MHz 3.5 180 40 Unit ns mA mA Pin Configurations 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 CY7C1356C (512 K × 18) 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 A NC NC VDDQ VSS NC DQPa DQa DQa VSS VDDQ DQa DQa VSS NC VDD ZZ DQa DQa VDDQ VSS DQa DQa NC NC VSS VDDQ NC NC NC A A A A A A A NC(36) NC(72) VSS VDD NC(288) NC(144) 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 NC DQPb NC DQb NC DQb VDDQ VDDQ VSS VSS NC DQb DQb NC DQb DQb DQb DQb VSS VSS VDDQ VDDQ DQb DQb DQb DQb NC VSS VDD NC VDD NC VSS ZZ DQb DQa DQa DQb VDDQ VDDQ VSS VSS DQa DQb DQa DQb DQa DQPb NC DQa VSS VSS VDDQ VDDQ NC DQa DQa NC DQPa NC MODE A A A A A1 A0 Document Number: 38-05538 Rev. *K A A A A A A A NC(36) NC(72) VSS DQd DQd VDDQ VSS DQd DQd DQd DQd VSS VDDQ DQd DQd DQPd CY7C1354C (256 K × 36) VSS VDD NC NC(288) NC(144) DQc DQc NC VDD 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 VSS DQc DQc DQc DQc VSS VDDQ 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 MODE A A A A A1 A0 DQPc DQc DQc VDDQ A A A A CE1 CE2 NC NC BWb BWa CE3 VDD VSS CLK WE CEN OE ADV/LD NC(18) A A A 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 A A CE1 CE2 BWd BWc BWb BWa CE3 VDD VSS CLK WE CEN OE ADV/LD NC(18) A Figure 1. 100-pin TQFP Page 4 of 32 [+] Feedback CY7C1354C, CY7C1356C Figure 2. 119-ball BGA Pinout CY7C1354C (256 K × 36) 1 2 3 4 5 6 7 A VDDQ A A NC/18M A A VDDQ B C D E F G H J K L M N P NC/576M NC/1G DQc CE2 A DQPc A A VSS ADV/LD VDD NC A A VSS CE3 A DQPb NC NC DQb CE1 VSS DQb DQb OE A VSS DQb VDDQ BWb DQb DQb WE VDD VSS NC DQb VDD DQb VDDQ CLK NC VSS BWa DQa DQa DQa DQa R T U DQc DQc VSS VDDQ DQc VSS DQc DQc DQc VDDQ DQc VDD BWc VSS NC DQd DQd DQd DQd BWd VDDQ DQd VSS DQa VDDQ DQd VSS CEN A1 VSS DQd VSS DQa DQa DQd DQPd VSS A0 VSS DQPa DQa NC/144M A MODE VDD NC/288M NC/72M A A NC A A NC NC/36M ZZ VDDQ TMS TDI TCK TDO NC VDDQ VSS CY7C1356C (512 K x 18) A B C D E F G H J K L M N P R T U 1 2 3 4 5 6 7 VDDQ A A NC/18M A A VDDQ NC/576M CE2 A A A ADV/LD VDD A NC/1G A CE3 A NC NC DQb NC VSS NC VSS DQPa NC NC DQb VSS CE1 VSS NC DQa VDDQ NC VSS VSS DQa VDDQ NC DQb VDDQ DQb NC VDD BWb VSS NC OE A WE VDD VSS VSS NC NC DQa VDD DQa NC VDDQ NC DQb VSS CLK VSS NC DQa DQb NC VSS NC NC DQb VSS NC VDDQ DQb NC VSS CEN A1 BWa VSS DQa VDDQ VSS DQa NC NC DQPb VSS A0 VSS NC DQa NC/144M A MODE VDD NC A NC/288M NC/72M A A NC/36M A A ZZ VDDQ TMS TDI TCK TDO NC VDDQ Document Number: 38-05538 Rev. *K Page 5 of 32 [+] Feedback CY7C1354C, CY7C1356C Figure 3. 165-ball FBGA CY7C1354C (256 K × 36) 4 5 6 7 1 2 3 A B C D E F G H J K L M N P NC/576M A CE1 BWc BWb CE3 NC/1G A NC DQc CE2 VDDQ BWa VSS VDDQ BWd VSS VDD R MODE DQPc DQc VSS 8 9 10 11 ADV/LD A A NC CLK CEN WE OE NC/18M A NC VSS VSS VSS VSS VSS VDD VDDQ VDDQ NC DQb DQPb DQb DQc DQc VDDQ VDD VSS VSS VSS VDD VDDQ DQb DQb DQc DQc VDDQ VDD VSS VSS VSS VDD VDDQ DQb DQb DQc NC DQd DQc NC DQd VDDQ NC VDDQ VDD VDD VDD VSS VSS VSS VSS VSS VSS VSS VSS VSS VDD VDD VDD VDDQ VDDQ DQb NC DQa DQb ZZ DQa DQd DQd VDDQ VDD VSS VSS VSS VDD VDDQ DQa DQa DQd DQd VDDQ VDD VSS VSS VSS VDD VDDQ DQa DQa DQd DQPd DQd NC VDDQ VDDQ VDD VSS VSS NC VSS NC VSS NC VDD VSS VDDQ VDDQ DQa NC DQa DQPa A A TDI A1 TDO A A A NC/288M A A TMS A0 TCK A A A A NC/144M NC/72M NC/36M NC CY7C1356C (512 K × 18) A B C D E F G H J K L M N P R 1 2 3 4 5 6 7 8 9 10 11 NC/576M A CE1 NC CE3 CEN ADV/LD A A A NC/1G NC NC A NC DQb BWb NC VDDQ BWa CLK NC VDDQ VDDQ VSS VSS VSS OE VSS VDD A VSS WE VSS VSS NC/18M VSS VDD VDDQ NC NC DQPa DQa CE2 NC DQb VDDQ VDD VSS VSS VSS VDD VDDQ NC DQa NC DQb VDDQ VDD VSS VSS VSS VDD VDDQ NC DQa NC NC DQb DQb NC NC VDDQ NC VDDQ VDD VDD VDD VSS VSS VSS VSS VSS VSS VSS VSS VSS VDD VDD VDD VDDQ VDDQ NC NC DQa DQa ZZ NC DQb NC VDDQ VDD VSS VSS VSS VDD VDDQ DQa NC DQb NC VDDQ VDD VSS VSS VSS VDD VDDQ DQa NC DQb DQPb NC NC VDDQ VDDQ VDD VSS VSS NC VSS NC VSS NC VDD VSS VDDQ VDDQ DQa NC NC NC NC/144M NC/72M A A TDI A1 TDO A A A NC/288M NC/36M A A TMS A0 TCK A A A A MODE Document Number: 38-05538 Rev. *K NC Page 6 of 32 [+] Feedback CY7C1354C, CY7C1356C Pin Definitions Pin Name I/O Type Pin Description A0, A1, A Inputsynchronous Address inputs used to select one of the address locations. Sampled at the rising edge of the CLK. BWa,BWb, BWc,BWd, Inputsynchronous Byte write select inputs, active LOW. Qualified with WE to conduct writes to the SRAM. Sampled on the rising edge of CLK. BWa controls DQa and DQPa, BWb controls DQb and DQPb, BWc controls DQc and DQPc, BWd controls DQd and DQPd. WE Inputsynchronous Write enable input, active LOW. Sampled on the rising edge of CLK if CEN is active LOW. This signal must be asserted LOW to initiate a write sequence. ADV/LD Inputsynchronous Advance/load input used to advance the on-chip address counter or load a new address. When HIGH (and CEN is asserted LOW) the internal burst counter is advanced. When LOW, a new address can be loaded into the device for an access. After being deselected, ADV/LD should be driven LOW to load a new address. CLK Inputclock Clock input. Used to capture all synchronous inputs to the device. CLK is qualified with CEN. CLK is only recognized if CEN is active LOW. CE1 Inputsynchronous Chip enable 1 input, active LOW. Sampled on the rising edge of CLK. Used in conjunction with CE2 and CE3 to select/deselect the device. CE2 Inputsynchronous Chip enable 2 input, active HIGH. Sampled on the rising edge of CLK. Used in conjunction with CE1 and CE3 to select/deselect the device. CE3 Inputsynchronous Chip enable 3 input, active LOW. Sampled on the rising edge of CLK. Used in conjunction with CE1 and CE2 to select/deselect the device. OE InputOutput enable, active LOW. Combined with the synchronous logic block inside the device to asynchronous control the direction of the I/O pins. When LOW, the I/O pins are allowed to behave as outputs. When deasserted HIGH, I/O pins are tristated, and act as input data pins. OE is masked during the data portion of a Write sequence, during the first clock when emerging from a deselected state and when the device has been deselected. CEN Inputsynchronous Clock enable input, active LOW. When asserted LOW the clock signal is recognized by the SRAM. When deasserted HIGH the clock signal is masked. Since deasserting CEN does not deselect the device, CEN can be used to extend the previous cycle when required. DQS I/Osynchronous Bidirectional data I/O lines. As inputs, they feed into an on-chip data register that is triggered by the rising edge of CLK. As outputs, they deliver the data contained in the memory location specified by addresses during the previous clock rise of the read cycle. The direction of the pins is controlled by OE and the internal control logic. When OE is asserted LOW, the pins can behave as outputs. When HIGH, DQa–DQd are placed in a tristate condition. The outputs are automatically tristated during the data portion of a write sequence, during the first clock when emerging from a deselected state, and when the device is deselected, regardless of the state of OE. DQPX I/Osynchronous Bidirectional data parity I/O lines. Functionally, these signals are identical to DQ[a:d]. During write sequences, DQPa is controlled by BWa, DQPb is controlled by BWb, DQPc is controlled by BWc, and DQPd is controlled by BWd. MODE TDO Input strap pin Mode input. Selects the burst order of the device. Tied HIGH selects the interleaved burst order. Pulled LOW selects the linear burst order. MODE should not change states during operation. When left floating MODE will default HIGH, to an interleaved burst order. JTAG serial output synchronous Serial data out to the JTAG circuit. Delivers data on the negative edge of TCK. TDI JTAG serial input Serial data in to the JTAG circuit. Sampled on the rising edge of TCK. synchronous TMS Test mode select This pin controls the test access port state machine. Sampled on the rising edge of TCK. synchronous TCK JTAG-clock VDD Power supply Clock input to the JTAG circuitry. Power supply inputs to the core of the device. Document Number: 38-05538 Rev. *K Page 7 of 32 [+] Feedback CY7C1354C, CY7C1356C Pin Definitions Pin Name VDDQ (continued) I/O Type Pin Description I/O power supply Power supply for the I/O circuitry. VSS Ground NC – No connects. This pin is not connected to the die. NC (18, 36, 72, 144, 288, 576, 1G) – These pins are not connected. They will be used for expansion to the 18M, 36M, 72M, 144M 288M, 576M, and 1G densities. ZZ Ground for the device. Should be connected to ground of the system. InputZZ “sleep” Input. This active HIGH input places the device in a non-time-critical “sleep” asynchronous condition with data integrity preserved. For normal operation, this pin has to be LOW or left floating. ZZ pin has an internal pull-down. Functional Overview The CY7C1354C and CY7C1356C are synchronous-pipelined burst NoBL SRAMs designed specifically to eliminate wait states during write/read transitions. All synchronous inputs pass through input registers controlled by the rising edge of the clock. The clock signal is qualified with the clock enable input signal (CEN). If CEN is HIGH, the clock signal is not recognized and all internal states are maintained. All synchronous operations are qualified with CEN. All data outputs pass through output registers controlled by the rising edge of the clock. Maximum access delay from the clock rise (tCO) is 2.8 ns (250 MHz device). Accesses can be initiated by asserting all three chip enables (CE1, CE2, CE3) active at the rising edge of the clock. If clock enable (CEN) is active LOW and ADV/LD is asserted LOW, the address presented to the device will be latched. The access can either be a read or write operation, depending on the status of the write enable (WE). BW[d:a] can be used to conduct byte write operations. Write operations are qualified by the write enable (WE). All writes are simplified with on-chip synchronous self-timed write circuitry. Three synchronous chip enables (CE1, CE2, CE3) and an asynchronous output enable (OE) simplify depth expansion. All operations (reads, writes, and deselects) are pipelined. ADV/LD should be driven LOW once the device has been deselected to load a new address for the next operation. Single Read Accesses A read access is initiated when the following conditions are satisfied at clock rise: (1) CEN is asserted LOW, (2) CE1, CE2, and CE3 are all asserted active, (3) the write enable input signal WE is deasserted HIGH, and (4) ADV/LD is asserted LOW. The address presented to the address inputs is latched into the address register and presented to the memory core and control logic. The control logic determines that a read access is in progress and enables the requested data to propagate to the input of the output register. At the rising edge of the next clock the requested data is allowed to propagate through the output register and to the data bus within 2.8 ns (250 MHz device) provided OE is active LOW. After the first clock of the read access the output buffers are controlled by OE and the internal control logic. OE must be driven LOW for the device to drive out the requested data. During the second clock, a subsequent Document Number: 38-05538 Rev. *K operation (read/write/deselect) can be initiated. Deselecting the device is also pipelined. Therefore, when the SRAM is deselected at clock rise by one of the chip enable signals, its output tristates following the next clock rise. Burst Read Accesses The CY7C1354C and CY7C1356C have an on-chip burst counter that enables the user the ability to supply a single address and conduct up to four reads without reasserting the address inputs. ADV/LD must be driven LOW to load a new address into the SRAM, as described in the Single Read Accesses section. The sequence of the burst counter is determined by the MODE input signal. A LOW input on MODE selects a linear burst mode, a HIGH selects an interleaved burst sequence. Both burst counters use A0 and A1 in the burst sequence, and wrap around when incremented sufficiently. A HIGH input on ADV/LD increments the internal burst counter regardless of the state of chip enables inputs or WE. WE is latched at the beginning of a burst cycle. Therefore, the type of access (read or write) is maintained throughout the burst sequence. Single Write Accesses Write accesses are initiated when the following conditions are satisfied at clock rise: (1) CEN is asserted LOW, (2) CE1, CE2, and CE3 are all asserted active, and (3) the write signal WE is asserted LOW. The address presented to A0–A16 is loaded into the address register. The write signals are latched into the control logic block. On the subsequent clock rise the data lines are automatically tristated regardless of the state of the OE input signal. This enables the external logic to present the data on DQ and DQP (DQa,b,c,d/DQPa,b,c,d for CY7C1354C and DQa,b/DQPa,b for CY7C1356C). In addition, the address for the subsequent access (read/write/deselect) is latched into the address register if the appropriate control signals are asserted. On the next clock rise the data presented to DQ and DQP (DQa,b,c,d/DQPa,b,c,d for CY7C1354C and DQa,b/DQPa,b for CY7C1356C or a subset for byte write operations, see the table Partial Write Cycle Description on page 10 for details) inputs is latched into the device and the write is complete. Page 8 of 32 [+] Feedback CY7C1354C, CY7C1356C The data written during the write operation is controlled by BW (BWa,b,c,d for CY7C1354C and BWa,b for CY7C1356C) signals. The CY7C1354C/CY7C1356C provides byte write capability that is described in the Write Cycle Description table. Asserting the write enable input (WE) with the selected byte write select (BW) input will selectively write to only the desired bytes. Bytes not selected during a byte write operation remain unaltered. A synchronous self-timed write mechanism is provided to simplify the write operations. Byte write capability is included to greatly simplify read/modify/write sequences, which can be reduced to simple byte write operations. Sleep Mode The ZZ input pin is an asynchronous input. Asserting ZZ places the SRAM in a power conservation ‘sleep’ mode. Two clock cycles are required to enter into or exit from this ‘sleep’ mode. While in this mode, data integrity is guaranteed. Accesses pending when entering the “sleep” mode are not considered valid nor is the completion of the operation guaranteed. The device must be deselected prior to entering the “sleep” mode. CE1, CE2, and CE3, must remain inactive for the duration of tZZREC after the ZZ input returns LOW. Because the CY7C1354C and CY7C1356C are common I/O devices, data should not be driven into the device while the outputs are active. The output enable (OE) can be deasserted HIGH before presenting data to the DQ and DQP (DQa,b,c,d/DQPa,b,c,d for CY7C1354C and DQa,b/DQPa,b for CY7C1356C) inputs. Doing so will tristate the output drivers. As a safety precaution, DQ and DQP (DQa,b,c,d/DQPa,b,c,d for CY7C1354C and DQa,b/DQPa,b for CY7C1356C) are automatically tristated during the data portion of a write cycle, regardless of the state of OE. Table 1. Interleaved Burst Address Table (MODE = Floating or VDD) Burst Write Accesses Table 2. Linear Burst Address Table (MODE = GND) The CY7C1354C/CY7C1356C has an on-chip burst counter that enables the user the ability to supply a single address and conduct up to four write operations without reasserting the address inputs. ADV/LD must be driven LOW to load the initial address, as described in Single Write Accesses on page 8. When ADV/LD is driven HIGH on the subsequent clock rise, the chip enables (CE1, CE2, and CE3) and WE inputs are ignored and the burst counter is incremented. The correct BW (BWa,b,c,d for CY7C1354C and BWa,b for CY7C1356C) inputs must be driven in each cycle of the burst write to write the correct bytes of data. First Address A1, A0 00 01 10 11 First Address A1, A0 00 01 10 11 Second Address A1, A0 01 00 11 10 Second Address A1, A0 01 10 11 00 Third Address A1, A0 10 11 00 01 Third Address A1, A0 10 11 00 01 Fourth Address A1, A0 11 10 01 00 Fourth Address A1, A0 11 00 01 10 Table 3. ZZ Mode Electrical Characteristics Parameter IDDZZ tZZS tZZREC tZZI tRZZI Description Sleep mode standby current Device operation to ZZ ZZ recovery time ZZ active to sleep current ZZ Inactive to exit sleep current Document Number: 38-05538 Rev. *K Test Conditions ZZ VDD 0.2 V ZZVDD 0.2 V ZZ 0.2 V This parameter is sampled This parameter is sampled Min – – 2tCYC – 0 Max 50 2tCYC – 2tCYC – Unit mA ns ns ns ns Page 9 of 32 [+] Feedback CY7C1354C, CY7C1356C Truth Table The Truth Table for CY7C1354C and CY7C1356C follows. [2, 3, 4, 5, 6, 7, 8] Operation Address Used CE ZZ ADV/LD WE BWx OE CEN CLK DQ Deselect cycle None H L L X X X L L-H Tri-state Continue deselect cycle None X L H X X X L L-H Tri-state Read cycle (begin burst) External L L L H X L L L-H Data out (Q) Next X L H X X L L L-H Data out (Q) Read cycle (continue burst) NOP/dummy read (begin burst) Dummy read (continue burst) Write cycle (begin burst) External L L L H X H L L-H Tri-state Next X L H X X H L L-H Tri-state External L L L L L X L L-H Data in (D) Write cycle (continue burst) Next X L H X L X L L-H Data in (D) NOP/WRITE ABORT (begin burst) None L L L L H X L L-H Tri-state WRITE ABORT (continue burst) Next X L H X H X L L-H Tri-state IGNORE CLOCK EDGE (stall) SLEEP MODE Current X L X X X X H L-H - None X H X X X X X X Tri-state Partial Write Cycle Description The following table lists the Partial Write Cycle Description for CY7C1354C.[2, 3, 4, 9] Function (CY7C1354C) WE H BWd X BWc X BWb X BWa X Write– no bytes written L H H H H Write byte a –(DQa and DQPa) L H H H L Read Write byte b – (DQb and DQPb) L H H L H Write bytes b, a L H H L L Write byte c –(DQc and DQPc) L H L H H Write bytes c, a L H L H L Write bytes c, b L H L L H Write bytes c, b, a L H L L L Write byte d –(DQd and DQPd) L L H H H Write bytes d, a L L H H L Write bytes d, b L L H L H Write bytes d, b, a L L H L L Write bytes d, c L L L H H Write bytes d, c, a L L L H L Write bytes d, c, b L L L L H Write all bytes L L L L L Notes 2. X = “Don't Care”, H = Logic HIGH, L = Logic LOW, CE stands for all chip enables active. BWx = L signifies at least one bytewrite select is active, BWx = valid signifies that the desired byte write selects are asserted, see Write Cycle Description table for details. 3. Write is defined by WE and BWX. See Write Cycle Description table for details. 4. When a write cycle is detected, all I/Os are tri-stated, even during byte writes. 5. The DQ and DQP pins are controlled by the current cycle and the OE signal. 6. CEN = H inserts wait states. 7. Device will power up deselected and the I/Os in a tri-state condition, regardless of OE. 8. OE is asynchronous and is not sampled with the clock rise. It is masked internally during write cycles. During a read cycle DQs and DQPX = tri-state when OE is inactive or when the device is deselected, and DQs = data when OE is active. 9. Table only lists a partial listing of the byte write combinations. Any combination of BWX is valid. Appropriate write will be done based on which byte write is active. Document Number: 38-05538 Rev. *K Page 10 of 32 [+] Feedback CY7C1354C, CY7C1356C Partial Write Cycle Description The following table lists the Partial Write Cycle Description for CY7C1356C.[10, 11, 12, 13] Function (CY7C1356C) WE BWb BWa Read H x x Write – no bytes written L H H Write byte a (DQa and DQPa) L H L Write byte b – (DQb and DQPb) L L H Write both bytes L L L Notes 10. X = “Don't Care”, H = Logic HIGH, L = Logic LOW, CE stands for all chip enables active. BWx = L signifies at least one bytewrite select is active, BWx = valid signifies that the desired byte write selects are asserted, see Write Cycle Description table for details. 11. Write is defined by WE and BWX. See Write Cycle Description table for details. 12. When a write cycle is detected, all I/Os are tri-stated, even during byte writes. 13. Table only lists a partial listing of the byte write combinations. Any combination of BWX is valid. Appropriate write will be done based on which byte write is active. Document Number: 38-05538 Rev. *K Page 11 of 32 [+] Feedback CY7C1354C, CY7C1356C IEEE 1149.1 Serial Boundary Scan (JTAG) Test Access Port (TAP) The CY7C1354C/CY7C1356C incorporates a serial boundary scan test access port (TAP) in the BGA package only. The TQFP package does not offer this functionality. This part operates in accordance with IEEE Standard 1149.1-1900, but does not have the set of functions required for full 1149.1 compliance. These functions from the IEEE specification are excluded because their inclusion places an added delay in the critical speed path of the SRAM. Note that the TAP controller functions in a manner that does not conflict with the operation of other devices using 1149.1 fully compliant TAPs. The TAP operates using JEDEC-standard 3.3 V or 2.5 V I/O logic levels. Test Clock (TCK) The CY7C1354C/CY7C1356C contains a TAP controller, instruction register, boundary scan register, bypass register, and ID register. Test Data-In (TDI) Disabling the JTAG Feature It is possible to operate the SRAM without using the JTAG feature. To disable the TAP controller, TCK must be tied LOW (VSS) to prevent clocking of the device. TDI and TMS are internally pulled up and may be unconnected. They may alternately be connected to VDD through a pull up resistor. TDO should be left unconnected. Upon power-up, the device comes up in a reset state which does not interfere with the operation of the device. TAP Controller State Diagram 1 The test clock is used only with the TAP controller. All inputs are captured on the rising edge of TCK. All outputs are driven from the falling edge of TCK. Test Mode Select (TMS) The TMS input is used to give commands to the TAP controller and is sampled on the rising edge of TCK. It is allowable to leave this ball unconnected if the TAP is not used. The ball is pulled up internally, resulting in a logic HIGH level. The TDI ball is used to serially input information into the registers and can be connected to the input of any of the registers. The register between TDI and TDO is chosen by the instruction that is loaded into the TAP instruction register. TDI is internally pulled up and can be unconnected if the TAP is unused in an application. TDI is connected to the most significant bit (MSB) of any register. (See the TAP Controller Block Diagram.) Test Data-Out (TDO) The TDO output ball is used to serially clock data-out from the registers. The output is active depending upon the current state of the TAP state machine. The output changes on the falling edge of TCK. TDO is connected to the least significant bit (LSB) of any register. (See the TAP Controller State Diagram.) TAP Controller Block Diagram TEST-LOGIC RESET 0 0 RUN-TEST/ IDLE 1 SELECT DR-SCA N 1 SELECT IR-SCAN 0 1 2 1 0 CAPTURE-IR 0 SHIFT-DR 0 TDI SHIFT-IR 1 1 1 0 PAUSE-IR 1 Selection Circuitry TDO x . . . . . 2 1 0 Boundary Scan Register 0 PAUSE-DR Instruction Register Identification Register EXIT1-IR 0 Selection Circuitry 31 30 29 . . . 2 1 0 0 1 EXIT1-DR 0 1 EXIT2-DR 0 EXIT2-IR 1 0 TAP CONTROLLER UPDATE-IR 1 0 The 0/1 next to each state represents the value of TMS at the rising edge of TCK. Document Number: 38-05538 Rev. *K TCK TM S 1 UPDATE-DR 1 Bypass Register 0 1 CAPTURE-DR 0 0 0 1 Performing a TAP Reset A RESET is performed by forcing TMS HIGH (VDD) for five rising edges of TCK. This RESET does not affect the operation of the SRAM and may be performed while the SRAM is operating. At power-up, the TAP is reset internally to ensure that TDO comes up in a high Z state. Page 12 of 32 [+] Feedback CY7C1354C, CY7C1356C TAP Registers Registers are connected between the TDI and TDO balls and enable data to be scanned into and out of the SRAM test circuitry. Only one register can be selected at a time through the instruction register. Data is serially loaded into the TDI ball on the rising edge of TCK. Data is output on the TDO ball on the falling edge of TCK. Instruction Register Three-bit instructions can be serially loaded into the instruction register. This register is loaded when it is placed between the TDI and TDO balls as shown in the TAP Controller Block Diagram on page 12. Upon power up, the instruction register is loaded with the IDCODE instruction. It is also loaded with the IDCODE instruction if the controller is placed in a reset state as described in the previous section. When the TAP controller is in the Capture-IR state, the two least significant bits are loaded with a binary “01” pattern to enable fault isolation of the board-level serial test data path. Bypass Register To save time when serially shifting data through registers, it is sometimes advantageous to skip certain chips. The bypass register is a single-bit register that can be placed between the TDI and TDO balls. This enables data to be shifted through the SRAM with minimal delay. The bypass register is set LOW (VSS) when the BYPASS instruction is executed. Boundary Scan Register The boundary scan register is connected to all the input and bidirectional balls on the SRAM. The boundary scan register is loaded with the contents of the RAM I/O ring when the TAP controller is in the Capture-DR state and is then placed between the TDI and TDO balls when the controller is moved to the Shift-DR state. The EXTEST, SAMPLE/PRELOAD and SAMPLE Z instructions can be used to capture the contents of the I/O ring. The tables Boundary Scan Exit Order (256 K × 36) on page 17 and Boundary Scan Exit Order (512 K × 18) on page 18 show the order in which the bits are connected. Each bit corresponds to one of the bumps on the SRAM package. The MSB of the register is connected to TDI and the LSB is connected to TDO. Identification (ID) Register The ID register is loaded with a vendor-specific, 32-bit code during the Capture-DR state when the IDCODE command is loaded in the instruction register. The IDCODE is hardwired into the SRAM and can be shifted out when the TAP controller is in the Shift-DR state. The ID register has a vendor code and other information described in Identification Register Definitions on page 15. TAP Instruction Set Overview Eight different instructions are possible with the three-bit instruction register. All combinations are listed in the Instruction Codes table. Three of these instructions are listed as RESERVED and should not be used. The other five instructions are described in detail in this section. Document Number: 38-05538 Rev. *K The TAP controller used in this SRAM is not fully compliant to the 1149.1 convention because some of the mandatory 1149.1 instructions are not fully implemented. The TAP controller cannot be used to load address data or control signals into the SRAM and cannot preload the I/O buffers. The SRAM does not implement the 1149.1 commands EXTEST or INTEST or the PRELOAD portion of SAMPLE/PRELOAD; rather, it performs a capture of the I/O ring when these instructions are executed. Instructions are loaded into the TAP controller during the Shift-IR state when the instruction register is placed between TDI and TDO. During this state, instructions are shifted through the instruction register through the TDI and TDO balls. To execute the instruction once it is shifted in, the TAP controller needs to be moved into the Update-IR state. EXTEST EXTEST is a mandatory 1149.1 instruction which is to be executed whenever the instruction register is loaded with all 0s. EXTEST is not implemented in this SRAM TAP controller, and therefore this device is not compliant to 1149.1. The TAP controller does recognize an all-0 instruction. When an EXTEST instruction is loaded into the instruction register, the SRAM responds as if a SAMPLE/PRELOAD instruction has been loaded. There is one difference between the two instructions. Unlike the SAMPLE/PRELOAD instruction, EXTEST places the SRAM outputs in a high Z state. IDCODE The IDCODE instruction causes a vendor-specific, 32-bit code to be loaded into the instruction register. It also places the instruction register between the TDI and TDO balls and enables the IDCODE to be shifted out of the device when the TAP controller enters the Shift-DR state. The IDCODE instruction is loaded into the instruction register upon power up or whenever the TAP controller is given a test logic reset state. SAMPLE Z The SAMPLE Z instruction causes the boundary scan register to be connected between the TDI and TDO balls when the TAP controller is in a Shift-DR state. It also places all SRAM outputs into a High-Z state. SAMPLE/PRELOAD SAMPLE/PRELOAD is a 1149.1 mandatory instruction. When the SAMPLE/PRELOAD instructions are loaded into the instruction register and the TAP controller is in the Capture-DR state, a snapshot of data on the inputs and output pins is captured in the boundary scan register. The user must be aware that the TAP controller clock can only operate at a frequency up to 20 MHz, while the SRAM clock operates more than an order of magnitude faster. Because there is a large difference in the clock frequencies, it is possible that during the Capture-DR state, an input or output undergo a transition. The TAP may then try to capture a signal while in transition (metastable state). This does not harm the device, but there is no guarantee as to the value that will be captured. Repeatable results may not be possible. Page 13 of 32 [+] Feedback CY7C1354C, CY7C1356C To guarantee that the boundary scan register captures the correct value of a signal, the SRAM signal must be stabilized long enough to meet the TAP controller's capture setup plus hold times (tCS and tCH). The SRAM clock input might not be captured correctly if there is no way in a design to stop (or slow) the clock during a SAMPLE/PRELOAD instruction. If this is an issue, it is still possible to capture all other signals and simply ignore the value of the CK and CK# captured in the boundary scan register. After the data is captured, it is possible to shift out the data by putting the TAP into the Shift-DR state. This places the boundary scan register between the TDI and TDO pins. PRELOAD enables an initial data pattern to be placed at the latched parallel outputs of the boundary scan register cells prior to the selection of another boundary scan test operation. The shifting of data for the SAMPLE and PRELOAD phases can occur concurrently when required - that is, while data captured is shifted out, the preloaded data can be shifted in. BYPASS When the BYPASS instruction is loaded in the instruction register and the TAP is placed in a Shift-DR state, the bypass register is placed between the TDI and TDO balls. The advantage of the BYPASS instruction is that it shortens the boundary scan path when multiple devices are connected together on a board. Reserved These instructions are not implemented but are reserved for future use. Do not use these instructions. TAP Timing 1 2 Test Clock (TCK ) 3 t TH t TM SS t TM SH t TDIS t TDIH t TL 4 5 6 t CY C Test M ode Select (TM S) Test Data-In (TDI) t TDOV t TDOX Test Data-Out (TDO) DON’T CA RE UNDEFINED TAP AC Switching Characteristics Over the Operating Range[14, 15] Parameter Description Clock TCK clock cycle time tTCYC TCK clock frequency tTF TCK clock HIGH time tTH TCK clock LOW time tTL Output Times TCK clock LOW to TDO valid tTDOV TCK clock LOW to TDO invalid tTDOX Setup Times TMS setup to TCK clock rise tTMSS TDI setup to TCK clock rise tTDIS Capture setup to TCK rise tCS Hold Times TMS hold after TCK clock rise tTMSH TDI hold after clock rise tTDIH Capture hold after clock rise tCH Min Max Unit 50 – 20 20 – 20 – – ns MHz ns ns – 0 10 – ns ns 5 5 5 – – – ns ns ns 5 5 5 – – – ns ns ns Notes 14. tCS and tCH refer to the setup and hold time requirements of latching data from the boundary scan register. 15. Test conditions are specified using the load in TAP AC test Conditions. tR/tF = 1 ns. Document Number: 38-05538 Rev. *K Page 14 of 32 [+] Feedback CY7C1354C, CY7C1356C 3.3 V TAP AC Test Conditions 2.5 V TAP AC Test Conditions Input pulse levels ............................................... VSS to 3.3 V Input pulse levels ................................................VSS to 2.5 V Input rise and fall times ................................................... 1 ns Input rise and fall time..................................................... 1 ns Input timing reference levels ......................................... 1.5 V Input timing reference levels........................................ 1.25 V Output reference levels ................................................. 1.5 V Output reference levels................................................ 1.25 V Test load termination supply voltage ............................. 1.5 V Test load termination supply voltage............................ 1.25 V 3.3 V TAP AC Output Load Equivalent 2.5 V TAP AC Output Load Equivalent 1.25V 1.5V 50Ω 50Ω TDO TDO Z O= 50Ω Z O= 50Ω 20pF 20pF TAP DC Electrical Characteristics and Operating Conditions (0 °C < TA < +70 °C; VDD = 3.3 V ± 0.165 V unless otherwise noted)[16] Parameter VOH1 VOH2 VOL1 VOL2 VIH VIL IX Description Test Conditions Output HIGH voltage Output HIGH voltage Output LOW voltage Output LOW voltage Max Unit IOH = –4.0 mA, VDDQ = 3.3 V 2.4 – V IOH = –1.0 mA, VDDQ = 2.5 V 2.0 – V IOH = –100 µA IOL = 8.0 mA IOL = 100 µA Input HIGH voltage Input LOW voltage Input load current Min VDDQ = 3.3 V 2.9 – V VDDQ = 2.5 V 2.1 – V VDDQ = 3.3 V – 0.4 V VDDQ = 2.5 V – 0.4 V VDDQ = 3.3 V – 0.2 V VDDQ = 2.5 V – 0.2 V VDDQ = 3.3 V 2.0 VDD + 0.3 V VDDQ = 2.5 V 1.7 VDD + 0.3 V VDDQ = 3.3 V –0.3 0.8 V VDDQ = 2.5 V –0.3 0.7 V –5 5 µA GND < VIN < VDDQ Identification Register Definitions Instruction Field CY7C1354C Revision number (31:29) Cypress device ID (28:12)[17] 000 01011001000100110 Cypress JEDEC ID (11:1) ID register presence (0) CY7C1356C 000 Description Reserved for version number. 01011001000010110 Reserved for future use. 00000110100 00000110100 1 1 Allows unique identification of SRAM vendor. Indicate the presence of an ID register. Notes 16. All voltages referenced to VSS (GND). 17. Bit #24 is “1” in the Register Definitions for both 2.5 V and 3.3 V versions of this device. Document Number: 38-05538 Rev. *K Page 15 of 32 [+] Feedback CY7C1354C, CY7C1356C Scan Register Sizes Register Name Bit Size (× 36) Bit Size (× 18) Instruction 3 3 Bypass 1 1 ID 32 32 Boundary scan order (119-ball BGA package) 69 69 Boundary scan order (165-ball FBGA package) 69 69 Identification Codes Instruction Code Description EXTEST 000 Captures the input/output ring contents. Places the boundary scan register between the TDI and TDO. Forces all SRAM outputs to high Z state. IDCODE 001 Loads the ID register with the vendor ID code and places the register between TDI and TDO. This operation does not affect SRAM operation. SAMPLE Z 010 Captures the input/output contents. Places the boundary scan register between TDI and TDO. Forces all SRAM output drivers to a high Z state. RESERVED 011 Do Not Use: This instruction is reserved for future use. SAMPLE/PRELOAD 100 Captures the input/output ring contents. Places the boundary scan register between TDI and TDO. Does not affect the SRAM operation. RESERVED 101 Do Not Use: This instruction is reserved for future use. RESERVED 110 Do Not Use: This instruction is reserved for future use. BYPASS 111 Places the bypass register between TDI and TDO. This operation does not affect SRAM operation. Document Number: 38-05538 Rev. *K Page 16 of 32 [+] Feedback CY7C1354C, CY7C1356C Boundary Scan Exit Order (256 K × 36) Bit # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 119-ball ID K4 H4 M4 F4 B4 G4 C3 B3 D6 H7 G6 E6 D7 E7 F6 G7 H6 T7 K7 L6 N6 165-ball ID B6 B7 A7 B8 A8 A9 B10 A10 C11 E10 F10 G10 D10 D11 E11 F11 G11 H11 J10 K10 L10 Bit # 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 22 23 24 25 26 27 28 29 30 P7 N7 M6 L7 K6 P6 T4 A3 C5 M10 J11 K11 L11 M11 N11 R11 R10 P10 52 53 54 55 56 57 58 59 60 61 Document Number: 38-05538 Rev. *K 119-ball ID B5 A5 C6 A6 P4 N4 R6 T5 T3 R2 R3 P2 P1 L2 K1 N2 N1 M2 L1 K2 Not Bonded (Preset to 1) H1 G2 E2 D1 H2 G1 F2 E1 D2 C2 165-ball ID R9 P9 R8 P8 R6 P6 R4 P4 R3 P3 R1 N1 L2 K2 J2 M2 M1 L1 K1 J1 Not Bonded (Preset to 1) G2 F2 E2 D2 G1 F1 E1 D1 C1 B2 Page 17 of 32 [+] Feedback CY7C1354C, CY7C1356C Boundary Scan Exit Order (512 K × 18) Bit # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 119-ball ID K4 H4 M4 F4 B4 G4 C3 B3 T2 Not Bonded (Preset to 0) Not Bonded (Preset to 0) Not Bonded (Preset to 0) D6 E7 F6 G7 H6 T7 K7 L6 N6 P7 Not Bonded (Preset to 0) Not Bonded (Preset to 0) Not Bonded (Preset to 0) Not Bonded (Preset to 0) Not Bonded (Preset to 0) T6 A3 C5 B5 A5 C6 A6 P4 N4 165-ball ID B6 B7 A7 B8 A8 A9 B10 A10 A11 Not Bonded (Preset to 0) Not Bonded (Preset to 0) Not Bonded (Preset to 0) C11 D11 E11 F11 G11 H11 J10 K10 L10 M10 Not Bonded (Preset to 0) Not Bonded (Preset to 0) Not Bonded (Preset to 0) Not Bonded (Preset to 0) Not Bonded (Preset to 0) R11 R10 P10 R9 P9 R8 P8 R6 P6 Document Number: 38-05538 Rev. *K Bit # 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 119-ball ID R6 T5 T3 R2 R3 Not Bonded (Preset to 0) Not Bonded (Preset to 0) Not Bonded (Preset to 0) Not Bonded (Preset to 0) P2 N1 M2 L1 K2 Not Bonded (Preset to 1) H1 G2 E2 D1 Not Bonded (Preset to 0) Not Bonded (Preset to 0) Not Bonded (Preset to 0) Not Bonded (Preset to 0) Not Bonded (Preset to 0) C2 A2 E4 B2 Not Bonded (Preset to 0) G3 Not Bonded (Preset to 0) L5 B6 165-ball ID R4 P4 R3 P3 R1 Not Bonded (Preset to 0) Not Bonded (Preset to 0) Not Bonded (Preset to 0) Not Bonded (Preset to 0) N1 M1 L1 K1 J1 Not Bonded (Preset to 1) G2 F2 E2 D2 Not Bonded (Preset to 0) Not Bonded (Preset to 0) Not Bonded (Preset to 0) Not Bonded (Preset to 0) Not Bonded (Preset to 0) B2 A2 A3 B3 Not Bonded (Preset to 0) Not Bonded (Preset to 0) A4 B5 A6 Page 18 of 32 [+] Feedback CY7C1354C, CY7C1356C Maximum Ratings Exceeding maximum ratings may impair the useful life of the device. These user guidelines are not tested. Storage temperature ................................ –65 °C to +150 °C Neutron Soft Error Immunity Parameter Ambient temperature with power applied ........................................... –55 °C to +125 °C Supply voltage on VDDQ relative to GND....... –0.5 V to +VDD Unit 25 °C 320 368 FIT/ Mb LMBU Logical multi-bit upsets 25 °C 0 0.01 FIT/ Mb Single event latch-up 85 °C 0 0.1 FIT/ Dev SEL Static discharge voltage........................................... > 2001 V (per MIL-STD-883, method 3015) Max* Logical single-bit upsets DC input voltage .................................. –0.5 V to VDD + 0.5 V Current into outputs (LOW) ......................................... 20 mA Test Condi- Typ tions LSBU Supply voltage on VDD relative to GND ........–0.5 V to +4.6 V DC to outputs in tri-state ....................–0.5 V to VDDQ + 0.5 V Description * No LMBU or SEL events occurred during testing; this column represents a statistical 2, 95% confidence limit calculation. For more details refer to Application Note AN 54908 “Accelerated Neutron SER Testing and Calculation of Terrestrial Failure Rates”. Latch-up current ..................................................... > 200 mA Operating Range Range Commercial Industrial Ambient Temperature VDD VDDQ 0 °C to +70 °C 3.3 V– 5% / + 10% 2.5 V – 5% to VDD –40 °C to +85 °C Electrical Characteristics Over the Operating Range[18, 19] Parameter Description Test Conditions Min Max Unit VDD Power supply voltage VDDQ I/O supply voltage 3.135 3.6 V for 3.3 V I/O 3.135 VDD V VOH Output HIGH voltage for 2.5 V I/O for 3.3 V I/O, IOH =4.0 mA 2.375 2.625 V 2.4 – V for 2.5 V I/O, IOH =1.0 mA 2.0 – V VOL Output LOW voltage for 3.3 V I/O, IOL=8.0 mA – 0.4 V VIH Input HIGH voltage VIL Input LOW voltage[20] IX Input leakage current except ZZ and MODE GND VI VDDQ Input current of MODE Input = VSS Input = VDD Input current of ZZ Input = VSS – 30 A –5 5 A for 2.5 V I/O, IOL=1.0 mA – 0.4 V 2.0 VDD + 0.3 V V for 2.5 V I/O 1.7 VDD + 0.3 V V for 3.3 V I/O –0.3 0.8 V for 2.5 V I/O –0.3 0.7 V –5 5 A –30 – A – 5 A –5 – A for 3.3 V I/O Input = VDD IOZ Output leakage current GND VI VDDQ, output disabled Notes 18. Overshoot: VIH(AC) < VDD + 1.5 V (Pulse width less than tCYC/2), undershoot: VIL(AC) > –2 V (Pulse width less than tCYC/2). 19. TPower-up: Assumes a linear ramp from 0 V to VDD (min) within 200 ms. During this time VIH < VDD and VDDQ <VDD. 20. Tested initially and after any design or process changes that may affect these parameters. Document Number: 38-05538 Rev. *K Page 19 of 32 [+] Feedback CY7C1354C, CY7C1356C Electrical Characteristics Over the Operating Range[18, 19] (continued) Parameter Min Max Unit 4 ns cycle, 250 MHz – 250 mA 5 ns cycle, 200 MHz – 220 mA 6 ns cycle, 166 MHz – 180 mA Automatic CE power-down current—TTL inputs Max VDD, device deselected, VIN 4 ns cycle, 250 MHz VIH or VIN VIL, 5 ns cycle, 200 MHz f = fMAX = 1/tCYC 6 ns cycle, 166 MHz – 130 mA – 120 mA – 110 mA ISB2 Automatic CE power-down current—CMOS inputs Max VDD, device deselected, All speed grades VIN 0.3 V or VIN > VDDQ 0.3 V, f=0 – 40 mA ISB3 Automatic CE power-down current—CMOS inputs Max VDD, device deselected, 4 ns cycle, 250 MHz VIN 0.3 V or VIN > VDDQ 0.3 V, 5 ns cycle, 200 MHz f = fMAX = 1/tCYC 6 ns cycle, 166 MHz – 120 mA – 110 mA – 100 mA Automatic CE power-down current—TTL inputs Max VDD, device deselected, VIN VIH or VIN VIL, f = 0 – 40 mA IDD ISB1 ISB4 Description VDD operating supply Test Conditions VDD = Max, IOUT = 0 mA, f = fMAX = 1/tCYC All speed grades Capacitance[21] 100 TQFP Max 119 BGA Max 165 FBGA Max Unit Input capacitance 5 5 5 pF CCLK TA = 25 C, f = 1 MHz, V DD = 3.3 V VDDQ = 2.5 V Clock input capacitance 5 5 5 pF CI/O Input/output capacitance 5 7 7 pF Test Conditions 100 TQFP Max 119 BGA Max 165 FBGA Max Unit Test conditions follow standard test methods and procedures for measuring thermal impedance, per EIA/JESD51. 29.41 34.1 16.8 °C/W 6.13 14.0 3.0 °C/W Parameter CIN Description Test Conditions Thermal Resistance[21] Parameter Description JA Thermal resistance (junction to ambient) JC Thermal resistance (junction to case) Note 21. Tested initially and after any design or process changes that may affect these parameters. Document Number: 38-05538 Rev. *K Page 20 of 32 [+] Feedback CY7C1354C, CY7C1356C Figure 4. AC Test Loads and Waveforms 3.3 V I/O Test Load R = 317 3.3 V OUTPUT OUTPUT RL = 50 Z0 = 50 VT = 1.5 V (a) Z0 = 50 VT = 1.25 V (a) Document Number: 38-05538 Rev. *K R = 351 10% (c) ALL INPUT PULSES VDDQ INCLUDING JIG AND SCOPE 1 ns (b) GND 5 pF R = 1538 (b) 90% 10% 90% 1 ns R = 1667 2.5 V OUTPUT RL = 50 GND 5 pF INCLUDING JIG AND SCOPE 2.5 V I/O Test Load OUTPUT ALL INPUT PULSES VDDQ 10% 90% 10% 90% 1 ns 1 ns (c) Page 21 of 32 [+] Feedback CY7C1354C, CY7C1356C Switching Characteristics Over the Operating Range [22, 23] Parameter tPower[24] Description VCC (typical) to the first access read or write –250 –200 –166 Unit Min Max Min Max Min Max 1 – 1 – 1 – ms 4.0 – 5 – 6 – ns Clock tCYC Clock cycle time FMAX Maximum operating frequency – 250 – 200 – 166 MHz tCH Clock HIGH 1.8 – 2.0 – 2.4 – ns tCL Clock LOW 1.8 – 2.0 – 2.4 – ns tEOV OE LOW to output valid – 2.8 – 3.2 – 3.5 ns tCLZ Z[25, 26, 27] 1.25 – 1.5 – 1.5 – ns Clock to low Output Times tCO Data output valid after CLK rise – 2.8 – 3.2 – 3.5 ns tEOV OE LOW to output valid – 2.8 – 3.2 – 3.5 ns tDOH Data output hold after CLK rise 1.25 – 1.5 – 1.5 – ns tCHZ Clock to high Z[25, 26, 27] 1.25 2.8 1.5 3.2 1.5 3.5 ns tCLZ Clock to low Z[25, 26, 27] tEOHZ tEOLZ 1.25 – 1.5 – 1.5 – ns Z[25, 26, 27] – 2.8 – 3.2 – 3.5 ns [25, 26, 27] 0 – 0 – 0 – ns OE HIGH to output high OE LOW to output low Z Setup Times tAS Address setup before CLK rise 1.4 – 1.5 – 1.5 – ns tDS Data input setup before CLK rise 1.4 – 1.5 – 1.5 – ns tCENS CEN setup before CLK rise 1.4 – 1.5 – 1.5 – ns tWES WE, BWx setup before CLK rise 1.4 – 1.5 – 1.5 – ns tALS ADV/LD setup before CLK rise 1.4 – 1.5 – 1.5 – ns tCES Chip select setup 1.4 – 1.5 – 1.5 – ns tAH Address hold after CLK rise 0.4 – 0.5 – 0.5 – ns tDH Data input hold after CLK rise 0.4 – 0.5 – 0.5 – ns tCENH CEN hold after CLK rise 0.4 – 0.5 – 0.5 – ns Hold Times tWEH WE, BWx hold after CLK rise 0.4 – 0.5 – 0.5 – ns tALH ADV/LD hold after CLK rise 0.4 – 0.5 – 0.5 – ns tCEH Chip select hold after CLK rise 0.4 – 0.5 – 0.5 – ns Notes 22. Timing reference level is 1.5 V when VDDQ = 3.3 V and is 1.25 V when VDDQ = 2.5 V. 23. Test conditions shown in (a) of Figure 4 on page 21 unless otherwise noted. 24. This part has a voltage regulator internally; tpower is the time power needs to be supplied above VDD minimum initially, before a Read or Write operation can be initiated. 25. tCHZ, tCLZ, tEOLZ, and tEOHZ are specified with AC test conditions shown in (b) of AC Test Loads. Transition is measured ± 200 mV from steady-state voltage. 26. At any given voltage and temperature, tEOHZ is less than tEOLZ and tCHZ is less than tCLZ to eliminate bus contention between SRAMs when sharing the same data bus. These specifications do not imply a bus contention condition, but reflect parameters guaranteed over worst case user conditions. Device is designed to achieve high Z prior to low Z under the same system conditions. 27. This parameter is sampled and not 100% tested. Document Number: 38-05538 Rev. *K Page 22 of 32 [+] Feedback CY7C1354C, CY7C1356C Switching Waveforms Figure 5. Read/Write Timing[28, 29, 30] 1 2 3 t CYC 4 5 6 A3 A4 7 8 9 A5 A6 10 CLK t CENS t CENH t CES t CEH t CL t CH CEN CE ADV/LD WE BW x A1 ADDRESS A2 A7 t CO t AS t DS t AH Data In-Out (DQ) t DH D(A1) t CLZ D(A2) D(A2+1) t DOH Q(A3) t OEV Q(A4) t CHZ Q(A4+1) D(A5) Q(A6) t OEHZ t DOH t OELZ OE WRITE D(A1) WRITE D(A2) BURST WRITE D(A2+1) READ Q(A3) DON’T CARE READ Q(A4) BURST READ Q(A4+1) WRITE D(A5) READ Q(A6) WRITE D(A7) DESELECT UNDEFINED Notes 28. For this waveform ZZ is tied low. 29. When CE is LOW, CE1 is LOW, CE2 is HIGH and CE3 is LOW. When CE is HIGH, CE1 is HIGH or CE2 is LOW or CE3 is HIGH. 30. Order of the Burst sequence is determined by the status of the MODE (0 = Linear, 1 = Interleaved). Burst operations are optional. Document Number: 38-05538 Rev. *K Page 23 of 32 [+] Feedback CY7C1354C, CY7C1356C Switching Waveforms (continued) Figure 6. NOP, STALL, and DESELECT Cycles[31, 32, 33] 1 2 A1 A2 3 4 5 A3 A4 6 7 8 9 10 CLK CEN CE ADV/LD WE BWx ADDRESS A5 t CHZ D(A1) Data Q(A2) D(A4) Q(A3) Q(A5) In-Out (DQ) WRITE D(A1) READ Q(A2) STALL READ Q(A3) WRITE D(A4) DON’T CARE STALL NOP READ Q(A5) DESELECT CONTINUE DESELECT UNDEFINED Notes 31. For this waveform ZZ is tied low. 32. When CE is LOW, CE1 is LOW, CE2 is HIGH and CE3 is LOW. When CE is HIGH, CE1 is HIGH or CE2 is LOW or CE3 is HIGH. 33. The IGNORE CLOCK EDGE or STALL cycle (Clock 3) illustrated CEN being used to create a pause. A write is not performed during this cycle. Document Number: 38-05538 Rev. *K Page 24 of 32 [+] Feedback CY7C1354C, CY7C1356C Switching Waveforms (continued) Figure 7. ZZ Mode Timing[34, 35] CLK t ZZ ZZ I t t ZZREC ZZI SUPPLY I DDZZ t RZZI A LL INPUTS DESELECT or READ Only (except ZZ) Outputs (Q) High-Z DON’T CARE Notes 34. Device must be deselected when entering ZZ mode. See cycle description table for all possible signal conditions to deselect the device. 35. I/Os are in high Z when exiting ZZ sleep mode. Document Number: 38-05538 Rev. *K Page 25 of 32 [+] Feedback CY7C1354C, CY7C1356C Ordering Information The table below contains only the parts that are currently available. If you don’t see what you are looking for, please contact your local sales representative. For more information, visit the Cypress website at www.cypress.com and refer to the product summary page at http://www.cypress.com/products Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives and distributors. To find the office closest to you, visit us at http://www.cypress.com/go/datasheet/offices Speed (MHz) 166 Ordering Code CY7C1354C-166AXC Package Diagram Part and Package Type 51-85050 100-pin Thin Quad Flat Pack (14 × 20 × 1.4 mm) Pb-free Operating Range Commercial CY7C1356C-166AXC CY7C1354C-166BGC 51-85115 119-ball Ball Grid Array (14 × 22 × 2.4 mm) CY7C1356C-166BGC CY7C1354C-166AXI 51-85050 100-pin Thin Quad Flat Pack (14 × 20 × 1.4 mm) Pb-free Industrial CY7C1354C-200AXC 51-85050 100-pin Thin Quad Flat Pack (14 × 20 × 1.4 mm) Pb-free Commercial CY7C1354C-200BGC 51-85115 119-ball Ball Grid Array (14 × 22 × 2.4 mm) CY7C1354C-200AXI 51-85050 100-pin Thin Quad Flat Pack (14 × 20 × 1.4 mm) Pb-free Industrial CY7C1354C-250AXC 51-85050 100-pin Thin Quad Flat Pack (14 × 20 × 1.4 mm) Pb-free Commercial CY7C1356C-166AXI 200 250 CY7C1356C-250AXC Ordering Code Definitions CY 7C 135X C - XXX XX X Temperature Range: X = C or I C = Commercial I = Industrial Package Type: XX = AX or BG AX = 100-pin Thin Quad Flat Pack (Pb-free) BG = 119-ball Ball Grid Array Speed Grade: XXX = 166 MHz / 200 MHz / 250 MHz Process Technology 90 nm 135X = 1354 or 1356 1354 = PL, 256 Kb × 36 (9 Mb) 1356 = PL, 512 Kb × 18 (9 Mb) Marketing Code: 7C = SRAMs Company ID: CY = Cypress Document Number: 38-05538 Rev. *K Page 26 of 32 [+] Feedback CY7C1354C, CY7C1356C Package Diagrams Figure 8. 100-pin Thin Plastic Quad Flatpack (14 × 20 × 1.4 mm), 51-85050 51-85050 *D Document Number: 38-05538 Rev. *K Page 27 of 32 [+] Feedback CY7C1354C, CY7C1356C Figure 9. 119-ball BGA (14 × 22 × 2.4 mm), 51-85115 51-85115 *C Document Number: 38-05538 Rev. *K Page 28 of 32 [+] Feedback CY7C1354C, CY7C1356C Figure 10. 165-ball FBGA (13 × 15 × 1.4 mm), 51-85180 51-85180 *C Document Number: 38-05538 Rev. *K Page 29 of 32 [+] Feedback CY7C1354C, CY7C1356C Acronyms Document Conventions Acronym Description Units of Measure BGA ball grid array CMOS complementary metal oxide semiconductor ns nano seconds Symbol Unit of Measure CE chip enable V Volts CEN clock enable µA micro Amperes FPBGA fine-pitch ball grid array mA milli Amperes JTAG Joint Test Action Group ms milli seconds NoBL No Bus Latency MHz Mega Hertz OE output enable pF pico Farad SRAM static random access memory W Watts TCK test clock °C degree Celcius TDI test data input TMS test mode select TDO test data output TQFP thin quad flat pack WE write enable Document Number: 38-05538 Rev. *K Page 30 of 32 [+] Feedback CY7C1354C, CY7C1356C Document History Page Document Title: CY7C1354C/CY7C1356C 9-Mbit (256 K × 36/512 K × 18) Pipelined SRAM with NoBL™ Architecture Document Number: 38-05538 REV. ECN No. Submission Date Orig. of Change Description of Change ** 242032 See ECN RKF New data sheet *A 278130 See ECN RKF Changed Boundary Scan order to match the B Rev of these devices Changed TQFP pkg to Lead-free TQFP in Ordering Information section Added comment of Lead-free BG and BZ packages availability *B 284431 See ECN VBL Changed ISB1 and ISB3 from DC Characteristic table as follows ISB1: 225 mA-> 130 mA, 200 MHz -> 120 mA, 167 MHz -> 110 mA ISB3: 225 MHz -> 120 mA, 200 MHz -> 110 mA, 167 MHz -> 100 mA Add BG and BZ pkg lead-free part numbers to ordering info section *C 320834 See ECN PCI Changed 225 MHz to 250 MHz Address expansion pins/balls in the pinouts for all packages are modified as per JEDEC standard Unshaded frequencies of 250, 200, 166 MHz in AC/DC Tables and Selection Guide Changed JA and JC for TQFP Package from 25 and 9 C/W to 29.41 and 6.13 C/W respectively Changed JA and JC for BGA Package from 25 and 6 C/W to 34.1 and 14.0 C/W respectively Changed JA and JC for FBGA Package from 27 and 6 C/W to 16.8 and 3.0 C/W respectively Modified VOL, VOH test conditions Added Lead-Free product information Updated Ordering Information Table Changed from Preliminary to Final *D 351895 See ECN PCI Changed ISB2 from 35 to 40 mA Updated Ordering Information Table *E 377095 See ECN PCI Modified test condition in note# 15 from VDDQ < VDD to VDDQ VDD *F 408298 See ECN RXU Changed address of Cypress Semiconductor Corporation on Page# 1 from “3901 North First Street” to “198 Champion Court” Changed three-state to tri-state. Modified “Input Load” to “Input Leakage Current except ZZ and MODE” in the Electrical Characteristics Table. Replaced Package Name column with Package Diagram in the Ordering Information table. *G 501793 See ECN VKN Added the Maximum Rating for Supply Voltage on VDDQ Relative to GND Changed tTH, tTL from 25 ns to 20 ns and tTDOV from 5 ns to 10 ns in TAP AC Switching Characteristics table. Updated the Ordering Information table. *H 2756340 08/26/2009 VKN/AESA Updated template Included Soft Error Immunity Data Modified Ordering Information table by including parts that are available and modified the disclaimer for the Ordering information. *I 3033272 09/19/2010 *J 3052882 10/08/2010 NJY Removed obsolete part numbers. *K 3186089 03/02/2011 NJY Updated Ordering Information. Updated Package Diagrams. Document Number: 38-05538 Rev. *K NJY Added Ordering Code Definitions. Updated Package Diagrams. Added Acronyms and Units of Measure. Minor edits and updated in new template. Page 31 of 32 [+] Feedback CY7C1354C, CY7C1356C Sales, Solutions, and Legal Information Worldwide Sales and Design Support Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives, and distributors. To find the office closest to you, visit us at Cypress Locations. Products Automotive Clocks & Buffers Interface Lighting & Power Control PSoC Solutions cypress.com/go/automotive cypress.com/go/clocks psoc.cypress.com/solutions cypress.com/go/interface PSoC 1 | PSoC 3 | PSoC 5 cypress.com/go/powerpsoc cypress.com/go/plc Memory Optical & Image Sensing cypress.com/go/memory cypress.com/go/image PSoC cypress.com/go/psoc Touch Sensing cypress.com/go/touch USB Controllers Wireless/RF cypress.com/go/USB cypress.com/go/wireless © Cypress Semiconductor Corporation, 2006-2011. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be used for medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges. Any Source Code (software and/or firmware) is owned by Cypress Semiconductor Corporation (Cypress) and is protected by and subject to worldwide patent protection (United States and foreign), United States copyright laws and international treaty provisions. Cypress hereby grants to licensee a personal, non-exclusive, non-transferable license to copy, use, modify, create derivative works of, and compile the Cypress Source Code and derivative works for the sole purpose of creating custom software and or firmware in support of licensee product to be used only in conjunction with a Cypress integrated circuit as specified in the applicable agreement. Any reproduction, modification, translation, compilation, or representation of this Source Code except as specified above is prohibited without the express written permission of Cypress. Disclaimer: CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Cypress reserves the right to make changes without further notice to the materials described herein. Cypress does not assume any liability arising out of the application or use of any product or circuit described herein. Cypress does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress’ product in a life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges. Use may be limited by and subject to the applicable Cypress software license agreement. Document Number: 38-05538 Rev. *K Revised March 2, 2011 Page 32 of 32 No Bus Latency and NoBL are trademarks of Cypress Semiconductor Corporation. All products and company names mentioned in this document may be the trademarks of their respective holders. [+] Feedback