DCW05 5W DC-DC Regulated Dual Output Converter series Features : 2:1 wide input range 4:1 wide input range(option) 1000VDC I/O isolation 3000VDC I/O isolation(option) Built-in EMI filter Protections: Short circuit / Overload Cooling by free air convection Five-sided shield metal case 100% burn-in test Low cost / High reliability Approvals: FCC / CE 2 years warranty SPECIFICATION ORDER NO. DCW05A-05 DCW05B-05 DCW05C-05 DCW05A-12 DCW05B-12 DCW05C-12 DCW05A-15 DCW05B-15 DCW05C-15 DC VOLTAGE 5V 12V CURRENT RANGE 100 ~ 500mA 46 ~ 230mA RATED POWER OUTPUT 5W RIPPLE & NOISE (max.) Note.2 50mVp-p LINE REGULATION Note.3 0.5% LOAD REGULATION Note.4 VOLTAGE ACCURACY 38 ~ 190mA 5.5W 5.7W 60mVp-p 60mVp-p 0.5% 2.0% SWITCHING FREQUENCY INPUT 15V 50KHz min. VOLTAGE RANGE A: 9 ~ 18VDC EFFICIENCY (Typ.) 75% DC CURRENT FILTER B: 18 ~ 36VDC 77% C: 36 ~ 72VDC 77% 80% Full load A: 586mA B: 286mA C: 139mA No load C: 12mA A: 41mA B: 21mA 83% 82% 81% 85% 83% Pi network Fuse recommended 150 ~ 250% rated output load Protection type : Shunt down o/p voltage, re-power on to recover All output equipped with over current protection PROTECTION OVERLOAD PROTECTION SHORT CIRCUIT Protection type : Shun down o/p voltage, re-power on to recover -40 ~ +71 (refer to output load derating curve) WORKING TEMP. 20% ~ 90% RH non-condensing WORKING HUMIDITY ENVIRONMENT STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATION WITHSTAND VOLTAGE SAFETY & ISOLATION RESISTANCE -40 ~ +105 , 10 ~ 95% RH 0.03% / (0 ~ 50 ) 10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes I/P-O/P:1KVDC I/P-O/P: 100M Ohms / 500VDC / 25 / 70% RH EMC ISOLATION CAPACITANCE (Note. 5) EMI CONDUCTION & RADIATION Compliance to EN55022 Class B, FCC part 15 Class B Compliance to EN61000-4-2,3,4,5,6,8, light industry level, criteria A EMS IMMUNITY MTBF 900khrs min. MIL-HDBK-217F (25 ) OTHERS DIMENSION 80pF max. 31.8*20.3*12.2mm (L*W*H) or 1.25"*0.80"*0.48" inch (L*W*H) 15g PACKING Derating Curve Pin Configuration Mechanical Specification Unit:mm(inch) 22 3 BOTTOM VIEW 16 9 14 11 2.5( 0.10 ) 5.0( 0.20 ) Pin No. Output 2&3 9 11 14 16 22 & 23 - Vi n COM - Vo u t + Vo u t COM + Vi n 100 LOAD (%) 2 3.8(0.15) 17.8(0.70) 23 31.8(1.25) 4.6(0.18) 20.3(0.80) 80 -40 15.2(0.60) 0.6+ 0.1/-0(0.024) 0 25 50 60 71 Ta ( NOTE 100 12.2(0.48) ) 1.All parameters are specified at normal input, rated load, 25 70% RH ambient. 2.Ripple & noise are measured at 20MHz by using a 12" twisted pair terminated with a 0.1uf & 47uf capacitor. 3.Line regulation is measured from low line to high line at rated load. 4.Load regulation is measured from 20% to 100% rated load. 5.The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives. File Name:DCW05-SPEC 2011-03-14