AOZ8033 4-Line EMI Filter with Integrated ESD Protection General Description Features The AOZ8033 is an 4-line device integrating EMI filtering with ESD protection for each line. It is designed to suppress unwanted EMI/RFI signals and provide electrostatic discharge (ESD) protection in portable electronic equipment. This state-of-the-art device utilizes AOS leading edge Trench Vertical Structure [TVS]2 ™ technology for superior clamping performance and filter attenuation over the full operating display range. The AOZ8033 has been optimized for protection of color LCD displays and CCD camera lines in cellular phones and other portable consumer electronic devices. ● The AOZ8033 consists of four identical circuits comprised of TVS diodes for ESD protection, and a resistor–capacitor network for EMI/RFI filtering. A series resistor value of 100Ω and a capacitance value of 28pF are used to achieve -35dB minimum attenuation from 800MHz to 3.0GHz. The TVS diodes provide effective suppression of ESD voltages in excess of ±20kV (air discharge) and ±20kV (contact discharge). This exceeds IEC 61000-4-2, level 4 ESD immunity test. 4 lines for EMI filtering and ESD protection: – Exceeds IEC 61000-4-2, level 4 (ESD) immunity test – ±20kV (air discharge) and ±20kV (contact discharge) Trench Vertical Structure [TVS]2 ™ based technology used to achieve excellent ESD clamping & filter performance over the full operating display range ● ● Filter performance: -35db attenuation from 800MHz to 3.0GHz ● Low operating voltage: 5.0V ● Capacitance stability over wide range of voltages and temperatures ● DFN package: 1.2mm x 1.8mm, 0.4mm pitch ● Pb-Free device Applications ● EMI filtering and ESD protection for data lines ● LCD displays, camera interface, I/O interface ● Portable handheld devices, cell phones, PDA phones The AOZ8033 comes in an RoHS compliant, 1.2mm x 1.8mm, 0.4mm pitch DFN package and is rated over a -40°C to +85°C ambient temperature range. Typical Application D0 D1 D2 D3 100Ω CH1 28pF 28pF 100Ω CH2 28pF 28pF LCD/Camera Module 100Ω CH3 28pF 28pF 100Ω CH4 28pF 28pF Figure 1 Rev. 1.7 January 2009 www.aosmd.com Page 1 of 7 AOZ8033 Ordering Information Part Number Ambient Temperature Range Package Environmental AOZ8033DIL -40°C to +85°C DFN-8 RoHS Compliant Green Product All AOS products are offered in packages with Pb-free plating and compliant to RoHS standards. Parts marked as Green Products (with “L” suffix) use reduced levels of Halogens, and are also RoHS compliant. Please visit www.aosmd.com/web/quality/rohs_compliant.jsp for additional information. Pin Configuration 7 6 5 8 2 7 3 6 4 5 1 Exposed Pad (GND) 8 1 2 3 4 DFN-8 (Bottom View) Top View Pin Description Rev. 1.7 January 2009 Pin Number Pin Name Pin Function 1, 8 CH 1 Channel 1 Connections 2, 7 CH 2 Channel 2 Connections 3, 6 CH 3 Channel 3 Connections 4, 5 CH 4 Channel 4 Connections Exposed Pad GND Common Ground Connection www.aosmd.com Page 2 of 7 AOZ8033 Absolute Maximum Ratings Exceeding the Absolute Maximum ratings may damage the device. Parameter Rating Storage Temperature (TS) -65°C to +150°C ESD Rating per IEC61000-4-2, contact ESD Rating per IEC61000-4-2, air (1) ±20kV (1) ±20kV ESD Rating per Human Body Model(2) ±30kV Notes: 1. IEC 61000-4-2 discharge with CDischarge = 150pF, RDischarge = 330Ω. 2. Human Body Discharge per MIL-STD-883, Method 3015 CDischarge = 100pF, RDischarge = 1.5kΩ. Electrical Characteristics TA = 25°C unless otherwise specified. Symbol VRWM Parameter Reverse Working Voltage Conditions Max. Units 5.0 V 8 V 0.1 µA ILOAD = 1A, positive ILOAD = 1A, negative clamp(5)(6) 7.00 -3.00 V ILOAD = 5A, positive clamp(5)(6) ILOAD = 5A, negative clamp(5)(6) 8.00 -5.00 ILOAD = 12A, positive clamp(5)(6) ILOAD = 12A, negative clamp(5)(6) 10.00 -10.00 1mA(4) VBR Reverse Breakdown Voltage IT = IR Reverse Leakage Current VRWM = 3.3V VCL RCH fC Signal Clamp Voltage Min. Typ. (3) 6 7 clamp(5)(6) Total Series Resistance IR = 20mA 90 100 110 Cut-off Frequency Measured with 50Ω source and 50Ω load termination 90 MHz Attenuation from 800MHz to 3.0GHz VR = 0V Measured with 50Ω source and 50Ω load termination -35 dB Attenuation from 800MHz to 3.0GHz VR = 5V Measured with 50Ω source and 50Ω load termination -35 dB Ω Notes: 3. The working peak reverse voltage, VRWM, should be equal to or greater than the DC or continuous peak operating voltage level. 4. VBR is measured at the pulse test current IT. 5. Measurements performed using a 100ns Transmission Line Pulse (TLP) system. 6. Guaranteed by design. Rev. 1.7 January 2009 www.aosmd.com Page 3 of 7 AOZ8033 Typical Performance Characteristics Typical Line Capacitance vs. Reverse Bias Voltage (Normalized to Capacitance @ 2.5V) Insertion Loss Characteristics 1.8 0 -5 1.6 Normalized Capacitance -10 S21 (db) -15 -20 -25 -30 -35 -40 1.2 1.0 0.8 0.6 0.4 -45 -50 1.4 1 10 100 1000 0.2 0.0 10000 1.0 Frequency (MHz) 3.0 4.0 5.0 Clamping Voltage vs. Peak Pulse Current Analog Crosstalk 0 11 -20 10 Clamping Voltage, Vcl (V) S21 (db) 2.0 Reverse Biased Voltage (V) -40 -60 -80 -100 9 8 7 6 1 10 100 1000 0 10000 2 Frequency (MHz) 4 6 8 10 12 Peak Pulse Current, Ipp (A) Forward Voltage vs. Forward Current Typical Resistance vs. Temperature 12 110 10 Resistance (Ω) Forward Voltage (V) 105 8 6 100 95 4 2 0 2 4 6 8 10 12 90 -45 Forward Current (A) Rev. 1.7 January 2009 -25 -5 5 25 45 65 85 Temparature (°C) www.aosmd.com Page 4 of 7 AOZ8033 Package Dimensions, DFN 1.2 x 1.8, 8L D1 D b e D2 E E1 L Pin 1 ID (C0.2x45°) TOP VIEW Pin 1 Marking BOTTOM VIEW A SIDE VIEW A3 A1 Dimensions in millimeters RECOMMENDED LAND PATTERN 0.20 1.00 0.20 0.20 0.20 0.20 1.00 0.30 0.40 0.20 Symbols A Min. 0.50 A1 A3 b 0.00 Nom. 0.55 Dimensions in inches Symbols A Min. 0.020 — 0.05 0.152 Ref. 0.15 0.20 0.25 A1 A3 b 0.000 D D1 1.75 0.95 1.85 1.05 D D1 0.069 0.037 D2 E E1 1.15 0.25 0.200 Ref. 1.20 1.25 0.30 0.35 D2 E E1 0.045 0.010 0.008 Ref. 0.047 0.049 0.012 0.014 e L 0.20 0.40 BSC 0.25 0.30 e L 0.008 0.016 BSC 0.010 0.012 1.80 1.00 Max. 0.60 Nom. 0.022 Max. 0.024 — 0.002 0.006 Ref. 0.006 0.008 0.010 0.071 0.039 0.073 0.041 0.30 Notes: 1. Controlling dimension is millimeter, converted inch dimensions are not necessaily exact. 2. Warpage shall not exceed 0.10mm. 3. Marking is for package orientation reference only. Rev. 1.7 January 2009 www.aosmd.com Page 5 of 7 AOZ8033 Tape and Reel Dimensions, DFN 1.2 x 1.8, 8L Carrier Tape P2 P1 D1 D0 E1 K0 E2 E B0 Ref. 5° P0 T A0 Feeding Direction UNIT: mm Package DFN 1.8x1.2 A0 1.32 ±0.05 B0 1.92 ±0.05 K0 0.75 ±0.05 D0 ø1.55 ±0.05 D1 E ø0.55 8.00 ±0.05 +0.3/-0.1 E1 1.75 ±0.1 E2 3.50 ±0.05 P0 4.00 ±0.1 P1 4.0 ±0.1 P2 2.0 ±0.05 T 0.25 ±0.05 W1 Reel S K N M G R H W UNIT: mm Tape Size Reel Size 8mm ø178 M N W ø178.0 ±1.0 ø60.0 ±1.0 11.80 ±0.5 W1 H 9.0 ø13.0 ±0.5 +0.5/-0.2 S K 2.40 10.25 ±0.10 ±0.2 G R ø9.8 — Leader / Trailer & Orientation Trailer Tape 300mm Min. Rev. 1.7 January 2009 Components Tape Orientation in Pocket www.aosmd.com Leader Tape 500mm Min. Page 6 of 7 AOZ8033 Package Marking AAH15 Assembly Lot Code Week and Year Code Part Number Code Underline Denotes Green Product This data sheet contains preliminary data; supplementary data may be published at a later date. Alpha & Omega Semiconductor reserves the right to make changes at any time without notice. LIFE SUPPORT POLICY ALPHA & OMEGA SEMICONDUCTOR PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body or (b) support or sustain life, and (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury of the user. Rev. 1.7 January 2009 2. A critical component in any component of a life support, device, or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. www.aosmd.com Page 7 of 7