EPCOS B69967N2047C760 7-pole duplexer for wcdma Datasheet

Microwave Ceramics and Modules
7-Pole Duplexer for WCDMA
Preliminary Data Sheet
Duplexer
B69967N2047C760
Features
z SMD duplexer consisting of coupled resonators with stepped impedances
z Ba(NdSm)TiO3 (εr = 82 / TCf =0±10 ppm/K )
z Excellent reflow solderability
Index
Page 2
• Component drawing
• Recommended footprint
Page 3
• Characteristics
Page 4
• Maximum ratings
• Typical passband characteristic
Page 5
• Processing information
• Soldering requirements
• Delivery mode
ISSUE DATE
06.07.04
ISSUE
P1
PUBLISHER
SAW MWC PD
PAGE
1/5
Microwave Ceramics and Modules
7-Pole Duplexer for WCDMA
Preliminary Data Sheet
Duplexer
B69967N2047C760
marking
Component drawing
TX
C760
yww
RX
*depending in final pressing tool
View from below onto the solder terminals and view from beside
Recommended footprint
TX, RX, ANT, G solder pads
ground area below solder resist with vias
to second ground layer
connected to lines with an impedance of
50 Ohm
FR4 material
permitivity : 4.4
preferred thickness : 0.3
Vias: Ø0.3mm / mm²
For other thickness
correlation might be necessary
ISSUE DATE
06.07.04
ISSUE
P1
PUBLISHER
SAW MWC PD
PAGE
2/5
Microwave Ceramics and Modules
7-Pole Duplexer for WCDMA
Preliminary Data Sheet
Duplexer
B69967N2047C760
Characteristics Receiver
Center frequency
Insertion loss
Passband
Amplitude ripple (peak - peak)
Standing wave ratio
Impedance
Power
Attenuation
at DC to 1790 MHz
at 1790 to 1920 MHz
at 1920 to 1980 MHz
at 1980 to 2025 MHz
at 4030 to 4150 MHz
at 5950 to 6000 MHz
fc
αIL
B
∆α
SWR
Z
Pavg
α
min.
-
typ.
2140
1.3
max.
1.6
60
0.9
1.9
50
0.8
35 *
30
50
20
23 *
33 *
MHz
dB
MHz
dB
Ω
W
dB
dB
dB
dB
dB
dB
*depending on final pressing tool and final layout
Characteristics Transmitter
Center frequency
Insertion loss
Passband
Amplitude ripple (peak - peak)
Standing wave ratio
Impedance
Power
Attenuation
at DC to 1000 MHz
at 2110 to 2170 MHz
at 2400 to 2550 MHz
at 3840 to 3960 MHz
at 5760 to 5940 MHz
fc
αIL
B
∆α
SWR
Z
Pmax
α
min.
-
typ.
1950
1.1
max.
1.4
60
0.6
1.8
50
1.0
40
42
40
33 *
23 *
MHz
dB
MHz
dB
Ω
W
dB
dB
dB
dB
dB
*depending on final pressing tool and final layout
Isolation Tx – Rx
min.
max.
α
Attenuation
at 1920 to 1980 MHz
at 2110 to 2170 MHz
ISSUE DATE
typ.
06.07.04
ISSUE
50
45
P1
PUBLISHER
dB
dB
SAW MWC PD
PAGE
3/5
Microwave Ceramics and Modules
7-Pole Duplexer for WCDMA
Preliminary Data Sheet
Duplexer
B69967N2047C760
Maximum ratings
IEC climatic category (IEC 68-1)
- 40/+ 90/56
Operating temperature
Top -40 / +85
°C
Typical passband characteristic
ISSUE DATE
06.07.04
ISSUE
P1
PUBLISHER
SAW MWC PD
PAGE
4/5
Microwave Ceramics and Modules
7-Pole Duplexer for WCDMA
Preliminary Data Sheet
Duplexer
B69967N2047C760
Processing information
z Wettability to IEC 68-2-58: ≥ 75% (after aging)
Soldering Requirements
Profile for eutectic
SnPb solder paste
Profile for leadfree
solder paste
Soldering type
reflow
Maximum soldering temperature
235 (max. 2 sec.)
(measuring point on top surface of the component) 225 (max. 10 sec.)
reflow
260 (max. 2 sec.) °C
250 (max. 10 sec.) °C
Recommended soldering conditions (infrared):
within 10 sec.
Temp. [°C]
within 10 sec.
Temp. [°C]
245°C±5°C
215°C±10°C
20-40 sec.
30 sec.
Time [sec.]
2.5 °C/s
40-80 sec.
2-3 min.
Time [sec.]
> - 5 °C/s
RX
TX
C760
yww
Delivery mode
z Blister tape acc. to IEC 286-3, polyester, grey
z Pieces/tape: 3000
 EPCOS AG 2001. All Rights Reserved. Reproduction, publication and dissemination of this data sheet, enclosures hereto and the
information contained therein without EPCOS' prior express consent is prohibited.
The information contained in this data sheet describes the type of component and shall not be considered as guaranteed characteristics.
Purchase orders are subject to the General Conditions for the Supply of Products and Services of the Electrical and Electronics Industry
recommended by the ZVEI (German Electrical and Electronic Manufacturers' Association), unless otherwise agreed.
ISSUE DATE
06.07.04
ISSUE
P1
PUBLISHER
SAW MWC PD
PAGE
5/5
Similar pages