AOZ8000 Ultra-Low Capacitance TVS Diode Array General Description Features The AOZ8000 is a transient voltage suppressor array designed to protect high speed data lines from ESD and lightning. ● This device incorporates eight surge rated, low capacitance steering diodes and a TVS in a single package. During transient conditions, the steering diodes direct the transient to either the positive side of the power supply line or to ground. They may be used to meet the ESD immunity requirements of IEC 61000-4-2, Level 4. The TVS diodes provide effective suppression of ESD voltages: ±15kV (air discharge) and ±8kV (contact discharge). The AOZ8000 comes in SOT-23, DFN-6, and SC-70 packages. They are compatible with both lead free and SnPb assembly techniques. The small size, low capacitance and high ESD protection makes it ideal for protecting high speed video and data communication interfaces. ESD protection for high-speed data lines: – IEC 61000-4-2, level 4 (ESD) immunity test – ±15kV (air discharge) and ±8kV (contact discharge) – IEC 61000-4-5 (Lightning) 5A (8/20µs) – Human Body Model (HBM) ±15kV ● Small package saves board space ● Low insertion loss ● Protects four I/O lines ● Low capacitance between I/O lines: 0.9pF ● Low clamping voltage ● Low operating voltage: 5.0V Applications ● USB 2.0 power and data line protection ● Video graphics cards ● Monitors and flat panel displays ● Digital Video Interface (DVI) ● 10/100/1000 Ethernet ● Notebook computers Typical Application USB Host Controller +5V Downstream Ports VBUS RT D+ RT DVBUS GND AOZ8000 +5V VBUS RT D+ RT DGND Figure 1. 2 USB High Speed Ports Rev. 2.4 July 2010 www.aosmd.com Page 1 of 15 AOZ8000 Ordering Information Part Number Package AOZ8000HIL SC-70-6 AOZ8000DIL DFN-6 AOZ8000CIL SOT23-6 Environmental RoHS Compliant Green Prodcut AOS Green Products (with “L” suffix) use reduced levels of Halogens, and are also RoHS compliant. Please visit www.aosmd.com/web/quality/rohs_compliant.jsp for additional information. Pin Configuration CH1 1 6 CH4 VN 2 5 VP CH2 3 4 CH3 CH1 1 6 CH4 VN 2 5 VP CH2 3 4 CH3 SOT23-6/SC-70-6 DFN-6 (Top View) (Top View) Absolute Maximum Ratings Exceeding the Absolute Maximum ratings may damage the device. Parameter Rating VP – VN 6V Peak Pulse Current (IPP), tP = 8/20µs 5A Peak Power Dissipation (8 x 20µs@ 25°C) SC-70 DFN SOT-23 60W 70W 60W Storage Temperature (TS) -65°C to +150°C ESD Rating per IEC61000-4-2, Contact(1) ±8kV ESD Rating per IEC61000-4-2, Air(1) ±15kV Model(2) ±15kV ESD Rating per Human Body Notes: 1. IEC 61000-4-2 discharge with CDischarge = 150pF, RDischarge = 330Ω. 2. Human Body Discharge per MIL-STD-883, Method 3015 CDischarge = 100pF, RDischarge = 1.5kΩ. Maximum Operating Ratings Parameter Rating Junction Temperature (TJ) Rev. 2.4 July 2010 -55°C to +125°C www.aosmd.com Page 2 of 15 AOZ8000 Electrical Characteristics Symbol VRWM VBR Parameter Reverse Working Voltage Conditions Min. Between pin 5 and 2(4) (5) Reverse Breakdown Voltage IT = 1mA, between pins 5 and 2 IR Reverse Leakage Current VRWM = 5V, between pins 5 and 2 VF Diode Forward Voltage IF = 15mA VCL Channel Clamp Voltage Positive Transients Negative Transient IPP = 1A, tp = 100ns, any I/O pin to Ground(3)(6)(8) Channel Clamp Voltage Positive Transients Negative Transient IPP = 5A, tp = 100ns, any I/O pin to Ground(3)(6)(8) Channel Clamp Voltage Positive Transients Negative Transient IPP = 12A, tp = 100ns, any I/O pin to Ground(3)(6)(8) Junction Capacitance VR = 0V, f = 1MHz, any I/O pin to Ground(3)(6) Cj 0.70 VR = 0V, f = 1MHz, between I/O pins VR = 0V, f = 1MHz, any I/O pin to Channel Input Capacitance Matching VR = 0V, f = 1MHz, between I/O Max. Units 5.5 V 6.6 (3)(6) ΔCj Typ. Ground(3)(7) pins(3)(6) V 0.1 µA 1 V 10.0 -3.0 V V 11 -6.0 V V 15.0 -10.0 V V 1.85 1.94 pF 0.9 0.94 pF 1.0 1.17 pF 0.03 pF 0.85 Notes: 3. These specifications are guaranteed by design. 4. The working peak reverse voltage, VRWM, should be equal to or greater than the DC or continuous peak operating voltage level. 5. VBR is measured at the pulse test current IT. 6. Measurements performed with no external capacitor on VP (pin 5 floating). 7. Measurements performed with VP biased to 3.3 Volts (pin 5 @ 3.3V). 8. Measurements performed using a 100ns Transmission Line Pulse (TLP) system. Rev. 2.4 July 2010 www.aosmd.com Page 3 of 15 AOZ8000 Typical Performance Characteristics Clamping Voltage vs. Peak Pulse Current Typical Variation of CIN vs VR (tperiod = 100ns, tr = 1ns) (f = 1MHz, T = 25°C) 16 Vp (Pin 5) = Float 1.75 Clamping Voltage, VCL (V) Input Capacitance (pF) 2.00 1.50 1.25 1.00 Vp (Pin 5) = 3.3V 0.75 0.50 0.25 0.00 0.00 15 14 13 12 11 10 9 8 1.00 3.00 2.00 4.00 0 5.00 2 Input Voltage (V) Forward Voltage vs. Forward Current 4 6 8 Peak Pulse Current, IPP (A) 12 I/O – Gnd Insertion Loss (S21) vs. Frequency (tperiod = 100ns, tr = 1ns) (Vp = 3.3V) 12 10 Insertion Loss (dB) Forward Voltage (V) 10 8 6 4 1 0 -1 -2 -3 -4 -5 -6 -7 -8 -9 2 0 2 4 6 8 10 12 1 10 I/O – I/O Insertion Loss (S21) vs. Frequency 1000 Analog Crosstalk (I/O–I/O) vs. Frequency (Vp = Float) 1 0 -1 -2 -3 -4 -5 -6 -7 -8 -9 -10 20 Insertion Loss (dB) Insertion Loss (dB) 100 Frequency (MHz) Forward Current (A) 0 -20 -40 -60 -80 1 10 100 1000 10 100 1000 Frequency (MHz) Frequency (MHz) ESD Clamping 8kV Contact per IEC61000-4-2 Note: Data was taken with a 10X attenuator Rev. 2.4 July 2010 www.aosmd.com Page 4 of 15 AOZ8000 Application Information The AOZ8000 TVS is design to protect four data lines from fast damaging transient over-voltage by clamping it to a reference. When the transient on a protected data line exceed the reference voltage the steering diode is forward bias thus, conducting the harmful ESD transient away from the sensitive circuitry under protection. PCB Layout Guidelines Printed circuit board layout is the key to achieving the highest level of surge immunity on power and data lines. The location of the protection devices on the PCB is the simplest and most important design rule to follow. The AOZ8000 devices should be located as close as possible to the noise source. The placement of the AOZ8000 devices should be used on all data and power lines that enter or exit the PCB at the I/O connector. In most systems, surge pulses occur on data and power lines that enter the PCB through the I/O connector. Placing the AOZ8000 devices as close as possible to the noise source ensures that a surge voltage will be clamped before the pulse can be coupled into adjacent PCB traces. In addition, the PCB should use the shortest possible traces. A short trace length equates to low impedance, which ensures that the surge energy will be dissipated by the AOZ8000 device. Long signal traces will act as antennas to receive energy from fields that are produced by the ESD pulse. By keeping line lengths as short as possible, the efficiency of the line to act as an antenna for ESD related fields is reduced. Minimize interconnecting line lengths by placing devices with the most interconnect as close together as possible. The protection circuits should shunt the surge voltage to either the reference or chassis ground. Shunting the surge voltage directly to the IC’s signal ground can cause ground bounce. The clamping performance of TVS diodes on a single ground PCB can be improved by minimizing the impedance with relatively short and wide ground traces. The PCB layout and IC package parasitic inductances can cause significant overshoot to the TVS’s clamping voltage. The inductance of the PCB can be reduced by using short trace lengths and multiple layers Rev. 2.4 July 2010 with separate ground and power planes. One effective method to minimize loop problems is to incorporate a ground plane in the PCB design. The AOZ8000 ultra-low capacitance TVS is designed to protect four high speed data transmission lines from transient over-voltages by clamping them to a fixed reference. The low inductance and construction minimizes voltage overshoot during high current surges. When the voltage on the protected line exceeds the reference voltage the internal steering diodes are forward biased, conducting the transient current away from the sensitive circuitry. Good circuit board layout is critical for the suppression of ESD induced transients. The following guidelines are recommended: 1. Place the TVS near the IO terminals or connectors to restrict transient coupling. 2. Fill unused portions of the PCB with ground plane. 3. Minimize the path length between the TVS and the protected line. 4. Minimize all conductive loops including power and ground loops. 5. The ESD transient return path to ground should be kept as short as possible. 6. Never run critical signals near board edges. 7. Use ground planes whenever possible. 8. Avoid running critical signal traces (clocks, resets, etc.) near PCB edges. 9. Separate chassis ground traces from components and signal traces by at least 4mm. 10. Keep the chassis ground trace length-to-width ratio <5:1 to minimize inductance. 11. Protect all external connections with TVS diodes. www.aosmd.com Page 5 of 15 AOZ8000 VCC Reset Clock I/O GND SIM AOZ8000 SIM Card Port Connection TPBIASx 1μ 56Ω 56Ω IEEE 1394 Connector TPAx+ IEEE 1394 PHY TPAxTPBx+ TPBxGND 56Ω 5.1kΩ 56Ω 270p AOZ8000 IEEE1394 Port Connection AOZ8000 TRD0+ TRD0- Ethernet Controller TRD1+ RJ45 Connector TRD1TRD2+ TRD2TRD3+ TRD3- AOZ8000 10/100 Ethernet Port Connection Rev. 2.4 July 2010 www.aosmd.com Page 6 of 15 AOZ8000 Package Dimensions, SC70-6L D Gauge Plane 0.15mm e1 θ L E1 E e c b A2 A .010mm A1 Dimensions in millimeters RECOMMENDED LAND PATTERN 1.95 0.65 0.35 0.65 UNIT: mm Symbols A A1 A2 b Min. c D E e e1 0.08 1.85 1.80 E1 L θ 1.1 0.26 0° 0.00 0.7 0.15 Nom. — — 0.9 — Max. 1.10 0.10 1.00 0.30 — 0.22 2.10 2.15 2.30 2.40 0.65 BSC 1.30 BSC 1.30 0.36 4° 1.4 0.46 8° Dimensions in inches Symbols A A1 A2 b Min. 0.00 0.028 0.006 c D E e e1 0.003 0.073 0.071 E1 L θ 0.043 0.010 0° Nom. — — 0.035 — Max. 0.043 0.004 0.039 0.012 — 0.009 0.083 0.085 0.091 0.094 0.026 BSC 0.051 BSC 0.051 0.014 4° 0.055 0.018 8° Notes: 1. All dimensions are in millimeters. 2. Dimensions are inclusive of plating 3. Package body sizes exclude mold flash and gate burrs. Mold flash at the non-lead sides should be less than 3 mils. 4. Die is facing up for mold and facing down for trim/form; i.e., reverse trim/form. 5. Dimension L is measured in gauge plane. 6. Controlling dimension is millimeter, converted inch dimensions are not necessarily exact. Rev. 2.4 July 2010 www.aosmd.com Page 7 of 15 AOZ8000 Tape and Reel Dimensions, SC70-6L Carrier Tape P1 D1 P2 T E1 E2 E B0 K0 A0 D0 P0 Feeding Direction UNIT: mm Package SC-70, 6L (8mm) A0 2.40 ±0.10 B0 2.40 ±0.10 K0 1.19 ±0.10 D0 1.00 Min. D1 1.55 ±0.05 E 8.00 ±0.30 Reel E1 1.75 ±0.10 E2 3.50 ±0.05 P0 4.00 ±0.10 P1 4.00 ±0.10 P2 2.00 ±0.05 T 0.25 ±0.05 W1 S G N M K V R H W W N Tape Size Reel Size M 8mm ø180 ø180.00 ø60.50 9.00 ±0.30 ±0.50 W1 11.40 ±1.00 H K ø13.00 10.60 +0.50/-0.20 S 2.00 ±0.50 G ø9.00 R 5.00 V 18.00 Leader/Trailer and Orientation Trailer Tape 300mm min. or 75 empty pockets Rev. 2.4 July 2010 Components Tape Orientation in Pocket www.aosmd.com Leader Tape 500mm min. or 125 empty pockets Page 8 of 15 AOZ8000 Package Dimensions, SOT23-6L Gauge Plane D e1 Seating Plane 0.25mm c L E E1 θ1 e b A2 A .010mm A1 Dimensions in millimeters RECOMMENDED LAND PATTERN 2.40 0.80 0.95 0.63 UNIT: mm Dimensions in inches Symbols A A1 A2 Min. 0.90 0.00 0.80 Nom. — — 1.10 Max. 1.25 0.15 1.20 Symbols A A1 A2 Min. 0.035 0.00 0.031 Nom. — — 0.043 Max. 0.049 0.006 0.047 b c D E E1 0.30 0.08 2.70 2.50 1.50 0.40 0.13 2.90 2.80 1.60 0.50 0.20 3.10 3.10 1.70 b c D E E1 0.012 0.003 0.106 0.098 0.059 0.016 0.005 0.114 0.110 0.063 0.020 0.008 0.122 0.122 0.067 e e1 L θ1 0.95 BSC 1.90 BSC 0.30 — 0.60 0° — 8° e e1 L θ1 0.037 BSC 0.075 BSC 0.012 — 0.024 0° — 8° Notes: 1. Package body sizes exclude mold flash and gate burrs. Mold flash at the non-lead sides should be less than 5 mils each. 2. Dimension “L” is measured in gauge plane. 3. Tolerance ±0.100mm (4 mil) unless otherwise specified. 4. Followed from JEDEC MO-178C & MO-193C. 6. Controlling dimension is millimeter. Converted inch dimensions are not necessarily exact. Rev. 2.4 July 2010 www.aosmd.com Page 9 of 15 AOZ8000 Tape and Reel Dimensions, SOT23-5&6L Tape P2 P1 D1 D0 E1 K0 E2 E B0 A0 P0 Feeding Direction Unit: mm Package A0 B0 K0 D0 D1 E E1 E2 P0 P1 P2 T SOT23-5/6L LP 3.15 ±0.10 3.20 ±0.10 1.40 ±0.10 1.50 ±0.05 1.00 +0.10 / -0 8.00 ±0.30 1.75 ±0.10 3.50 ±0.05 4.00 ±0.10 4.00 ±0.10 2.00 ±0.05 0.23 ±0.03 Reel W1 S K R M N J H Unit: mm Tape Size Reel Size M N 8mm ø177.8 ø177.8 Max. 55.0 Min. W1 H 8.4 13.0 +1.50 / -0.0 +0.5 / -0.2 S K R J 1.5 Min 10.1 Min. 12.7 4.0 ±0.1 Leader/Trailer and Orientation Trailer Tape 300mm min. Rev. 2.4 July 2010 Components Tape Orientation in Pocket www.aosmd.com Leader Tape 500mm min. Page 10 of 15 AOZ8000 Package Dimensions, DFN 2 x 2 (Page 1 of 3) TOP VIEW D A B L2 E Pin 1 Mark 1 L2 Detail D SIDE VIEW 4x A2 A A1 A3 Detail C C Seating Plane BOTTOM VIEW e D4 6xb 1 E4 L E2 See Detail A 6 See Detail C D2 2x e Rev. 2.4 July 2010 www.aosmd.com Page 11 of 15 AOZ8000 Package Dimensions, DFN 2 x 2 (Page 2 of 3) L1 Exposed Slug/Heat Sink 0.17 0.30 L2 B Detail C 4xR Exposed Metalized Feature Edge of Plastic Body Detail A A1 Detail D Datum A or B Datum A or B 6x R1 6x R1 L e/2 e L2 Terminal Tip Terminal Tip e Even Terminal Side Odd Terminal Side Detail B RECOMMENDED LAND PATTERN 0.620 0.300 0.565 1.170 0.943 0.650 Unit: mm Rev. 2.4 July 2010 www.aosmd.com Page 12 of 15 AOZ8000 Package Dimensions, DFN 2 x 2 (Page 3 of 3) Dimensions in millimeters Dimensions in inches Symbols A Min. 0.80 Nom. 0.90 Max. 1.00 Symbols A Min. 0.031 Nom. 0.035 Max. 0.039 A1 0.00 0.025 0.05 A1 0.000 0.001 0.002 A2 A3 b 0.65 0.15 0.18 0.70 0.20 0.20 0.75 0.25 0.28 A2 A3 b 0.026 0.006 0.007 0.028 0.008 0.008 0.030 0.010 0.011 D 2.0 BSC D 0.079 BSC E e E4 2.0 BSC 0.65 BSC 0.56 0.66 0.76 E e E4 0.079 BSC 0.026 BSC 0.022 0.026 0.030 E2 0.84 0.94 1.04 E2 0.033 0.037 0.041 D4 D2 L 0.21 0.52 0.20 0.31 0.62 0.29 0.41 0.72 0.45 D4 D2 L 0.008 0.020 0.008 0.012 0.024 0.011 0.016 0.028 0.018 — — 0.125 0.075 REF 0.075 REF L1 L2 R R1 L1 L2 R R1 — — — — 0.005 0.003 REF 0.003 REF R2 aaa — 0.10 R2 aaa — 0.004 bbb ccc ddd eee θ 0.10 0.10 0.05 0.08 10° bbb ccc ddd eee θ 0.004 0.004 0.002 0.003 10° 0° 12° 0° 12° Notes: 1. Dimensioning and tolerances conform to ASME Y14.5M-1994. 2. All dimensions are in millimeters. All angles are in degrees. 3. The terminal #1 identifier and terminal numbering convention shall conform to JESD 95-1 SPP-012. Details of terminal #1 are optional, but must be located within the zone indicated. The terminal #1 identifier may be a molded, marked, or metalized feature. 4. Dimension b apply to metallized terminal and is measured between 0.15mm and 0.20mm from terminal tip. 5. Coplanarity applies to the exposed heat sink slug as well as the terminal. 6. Profile tolerance (aaa) will be applicable only to the plastic body, and not to the metallized fetures (such as terminal tips and tie bars.) Metallized features may protrude a maximum of L2 from the plastic body profile. 7. Corners will be sharp unless otherwise specified with radius dimensions. 8. This feature applies to both ends of the package. 9. If L1 max. is not called out, the metalized feature will extend to the exposed pad. Thus, the 0.17mm gap does not apply. Rev. 2.4 July 2010 www.aosmd.com Page 13 of 15 AOZ8000 Tape and Reel Dimensions, DFN 2 x 2 Carrier Tape P2 P1 D0 D1 E1 K0 E2 B0 T E A0 P0 Feeding Direction UNIT: mm Package DFN 2x2 A0 2.25 ±0.05 B0 2.25 ±0.05 K0 D0 D1 E E1 1.00 1.50 1.00 8.00 1.75 ±0.05 +0.10/-0 +0.25/-0 +0.30/-0.10 ±0.10 Reel E2 3.50 ±0.05 P0 4.00 ±0.10 P1 4.00 ±0.10 P2 2.00 ±0.10 T 0.254 ±0.02 W1 S R K M N H UNIT: mm Tape Size Reel Size M 8mm ø180 ø180.00 ±0.50 N 60.0 ±0.50 W1 8.4 +1.5/-0.0 H 13.0 ±0.20 S 1.5 Min. K 13.5 Min. R 3.0 ±0.50 Leader / Trailer & Orientation Trailer Tape 300mm Min. Rev. 2.4 July 2010 Components Tape Orientation in Pocket www.aosmd.com Leader Tape 500mm Min. Page 14 of 15 AOZ8000 Part Marking AOZ8000HIL (SOT-23) (SC70-6) ABOW Part Number Code Underscore Denotes Green Product LT AOZ8000CIL AWL Assembly Lot Code Part Number Code Underscore Denotes Green Product Year & Week Code Assembly Lot & Location Code Week & Year Code Option & Assembly Location Code AOZ8000DIL (DFN 2x2) Part Number Code Underscore Denotes Green Product Assembly Location Code AAOA Option Code YWLT Year & Week Code Assembly Lot Code This datasheet contains preliminary data; supplementary data may be published at a later date. Alpha & Omega Semiconductor reserves the right to make changes at any time without notice. LIFE SUPPORT POLICY ALPHA & OMEGA SEMICONDUCTOR PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body or (b) support or sustain life, and (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury of the user. Rev. 2.4 July 2010 2. A critical component in any component of a life support, device, or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. www.aosmd.com Page 15 of 15