Kingbright APPA3010SECK 3.0mmx1.0mm right angle smd chip led lamp Datasheet

3.0mmx1.0mm RIGHT ANGLE SMD CHIP LED
LAMP
Part Number: APPA3010SECK
Super Bright Orange
ATTENTION
OBSERVE PRECAUTIONS
FOR HANDLING
ELECTROSTATIC
DISCHARGE
SENSITIVE
DEVICES
Features
Descriptions
z 3.0mmx2.5mmx1.0mm right angle SMD LED, 1.0mm thickness.
z The Super Bright Orange device is made with AlGaInP
(on GaAs substrate) light emitting diode chip.
z Low power consumption.
z Ideal for back light and indicator.
z Electrostatic discharge and power surge could damage
the LEDs.
z Package : 2000pcs / reel.
z Moisture sensitivity level : level 3.
z Tinned pads for improved solderability.
z It is recommended to use a wrist band or antielectrostatic glove when handling the LEDs.
z All devices, equipments and machineries must be
z RoHS compliant.
electrically grounded.
Package Dimensions
Notes:
1. All dimensions are in millimeters (inches).
2. Tolerance is ±0.15(0.006") unless otherwise noted.
3. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice.
4. The device has a single mounting surface. The device must be mounted according to the specifications.
SPEC NO: DSAP0955
REV NO: V.1A
DATE: MAR/02/2017
PAGE: 1 OF 5
APPROVED: Wynec
CHECKED: Allen Liu
DRAWN: W.Q.Zhong
ERP: 1203007004
Selection Guide
Part No.
Emitting Color (Material)
APPA3010SECK
Iv (mcd) [2]
@ 20mA
Lens Type
Super Bright Orange (AlGaInP)
Water Clear
Viewing
Angle [1]
Min.
Typ.
400
650
*200
*380
2θ1/2
30°
Notes:
1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value.
2. Luminous intensity / luminous Flux: +/-15%.
* Luminous intensity value is traceable to CIE127-2007 standards.
Electrical / Optical Characteristics at TA=25°C
Symbol
Parameter
Emitting Color
Typ.
λpeak
Peak Wavelength
Super Bright Orange
λD [1]
Dominant Wavelength
Δλ1/2
Max.
Units
Test Conditions
610
nm
IF=20mA
Super Bright Orange
601
nm
IF=20mA
Spectral Line Half-width
Super Bright Orange
29
nm
IF=20mA
C
Capacitance
Super Bright Orange
15
pF
VF=0V;f=1MHz
VF [2]
Forward Voltage
Super Bright Orange
2.1
2.5
V
IF=20mA
IR
Reverse Current
Super Bright Orange
10
uA
VR=5V
Notes:
1. Wavelength: +/-1nm.
2. Forward Voltage: +/-0.1V.
3. Wavelength value is traceable to CIE127-2007 standards.
4. Excess driving current and / or operating temperature higher than recommended conditions may result in severe light degradation or
premature failure.
Absolute Maximum Ratings at TA=25°C
Parameter
Values
Units
Power dissipation
75
mW
DC Forward Current
30
mA
Peak Forward Current [1]
195
mA
5
V
Reverse Voltage
Operating Temperature
-40°C To +85°C
Storage Temperature
-40°C To +85°C
Notes:
1. 1/10 Duty Cycle, 0.1ms Pulse Width.
2. Relative humidity levels maintained between 40% and 60% in production area are recommended to avoid the build-up of static
electricity – Ref JEDEC/JESD625-A and JEDEC/J-STD-033.
SPEC NO: DSAP0955
REV NO: V.1A
DATE: MAR/02/2017
PAGE: 2 OF 5
APPROVED: Wynec
CHECKED: Allen Liu
DRAWN: W.Q.Zhong
ERP: 1203007004
Super Bright Orange
APPA3010SECK
SPEC NO: DSAP0955
REV NO: V.1A
DATE: MAR/02/2017
PAGE: 3 OF 5
APPROVED: Wynec
CHECKED: Allen Liu
DRAWN: W.Q.Zhong
ERP: 1203007004
APPA3010SECK
Recommended Soldering Pattern
(Units : mm; Tolerance: ± 0.1)
Reel Dimension
Tape Dimensions
(Units : mm)
SPEC NO: DSAP0955
REV NO: V.1A
DATE: MAR/02/2017
PAGE: 4 OF 5
APPROVED: Wynec
CHECKED: Allen Liu
DRAWN: W.Q.Zhong
ERP: 1203007004
PACKING & LABEL SPECIFICATIONS
APPA3010SECK
Terms and conditions for the usage of this document
1. The information included in this document reflects representative usage scenarios and is intended for technical reference only.
2. The part number, type, and specifications mentioned in this document are subject to future change and improvement without
notice. Before production usage customer should refer to the latest datasheet for the updated specifications.
3. When using the products referenced in this document, please make sure the product is being operated within the environmental
and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible
for any subsequent issues.
4. The information in this document applies to typical usage in consumer electronics applications. If customer's application has
special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with
Kingbright representative for further assistance.
5. The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright.
6. All design applications should refer to Kingbright application notes available at http://www.KingbrightUSA.com/ApplicationNotes
SPEC NO: DSAP0955
REV NO: V.1A
DATE: MAR/02/2017
PAGE: 5 OF 5
APPROVED: Wynec
CHECKED: Allen Liu
DRAWN: W.Q.Zhong
ERP: 1203007004
Similar pages