SMT inductors – SIMID series SIMID 2220-T Series/Type: B82442T Date: 2010-07-05 Content of header bars 1 and 2 of data sheet will be automatically entered in headers and footers! Please fill in the table and then change the color to "white". This ensures that the table disappears (invisible) for the customer PDF. Don't change formatting when entering or pasting text in the table and don't add any cell or line in and to it! Identification/Classification 1 (header 1 + top left bar): SMT inductors – SIMID series Identification/Classification 2 (header 2 + bottom left header bar): SIMID 2220-T Identification/Classification 3 (header 3) Ordering code: (bottom right header bar) Series/Type: (top right header bar) B82442T Preliminary data (optional): (if necessary) Department: Date: 2010-07-05 Version: 2 EPCOS AG 2010. Reproduction, publication and dissemination of this publication, enclosures hereto and the information contained therein without EPCOS' prior express consent is prohibited. SMT inductors – SIMID series SIMID 2220-T B82442T Size 2220 (EIA) or 5650 (IEC) Rated inductance 1 µH to 10000 µH Rated current 46 mA to 3510 mA Construction Ferrite drum core Laser-welded winding Flame-retardant molding Features Temperature range up to 150 °C Very high current handling capability High L values Qualified to AEC-Q200 Suitable for lead-free reflow soldering as referenced in JEDEC J-STD 020C RoHS-compatible Halogen-free Applications Filtering of supply voltages, coupling, decoupling DC/DC converters/switch-mode power supplies Automotive electronics Telecommunications Consumer electronics Industrial electronics Terminals Base material CuSn6 Layer composition Ni, Sn (lead-free) Electro-plated Marking Marking on component: Manufacturer, letter “T”, L value (in µH), tolerance of L value (coded), date of manufacture (YWWD) Minimum data on reel: Manufacturer, ordering code, L value, quantity, date of packing Delivery mode and packing unit 12-mm blister tape, wound on 330-mm ∅ reel Packing unit: 1500 pcs./reel Please read Cautions and warnings and Important notes at the end of this document. Page 2 of 9 2010-07-05 SMT inductors – SIMID series SIMID 2220-T B82442T Dimensional drawing and layout recommendation Taping and packing Please read Cautions and warnings and Important notes at the end of this document. Page 3 of 9 2010-07-05 SMT inductors – SIMID series SIMID 2220-T B82442T Technical data and measuring conditions Rated inductance LR Measured with impedance analyzer Agilent 4294A at frequency fL, 0.1 V, 20 °C Q factor Qmin Measured with impedance analyzer Agilent 4294A at frequency fQ, 20 °C Rated temperature TR 85 °C Rated current IR Maximum permissible DC with temperature increase of ≤ 65 K at rated temperature Saturation current Isat Maximum permissible DC with inductance decrease ∆L/L0 ≤ 10%, 20 °C Self-resonance frequency fres,min Measured with network analyzer Agilent 8753D, 20 °C DC resistance Rmax Measured at 20 °C Solderability (lead-free) Sn95.5Ag3.8Cu0.7: (245 ±5) °C, (5 ±0.3) s Wetting of soldering area ≥ 90% (based on IEC 60068-2-58) Resistance to soldering heat 260 °C, 40 s (as referenced in JEDEC J-STD 020C) Climatic category 55/150/56 (to IEC 60068-1) Storage conditions Mounted: –55 °C … +150 °C Packaged: –25 °C … +40 °C, ≤ 75% RH Weight Approx. 0.4 g Please read Cautions and warnings and Important notes at the end of this document. Page 4 of 9 2010-07-05 SMT inductors – SIMID series SIMID 2220-T B82442T Characteristics and ordering codes LR fL;fQ MHz IR mA Isat mA Rmax 15 15 15 7.96 7.96 7.96 3510 3020 2710 7330 5480 4820 0.025 0.033 0.038 111 60 46 B82442T1102M050 B82442T1152M050 B82442T1222M050 15 15 15 7.96 7.96 7.96 2460 1950 1680 4010 3450 2770 0.046 0.073 0.106 36 30 23 B82442T1332M050 B82442T1472M050 B82442T1682M050 15 15 15 2.52 2.52 2.52 1420 1380 1260 2280 2160 1870 0.132 0.141 0.190 19 19 16 B82442T1103K050 B82442T1123K050 B82442T1153K050 18 22 27 15 15 15 2.52 2.52 2.52 1090 1040 880 1780 1590 1400 0.210 0.238 0.307 14 13 11 B82442T1183K050 B82442T1223K050 B82442T1273K050 33 39 47 15 15 15 2.52 2.52 2.52 840 720 700 1380 1190 1120 0.360 0.456 0.519 11 9.0 8.0 B82442T1333K050 B82442T1393K050 B82442T1473K050 56 68 82 15 15 15 2.52 2.52 2.52 600 570 540 1010 900 830 0.679 0.781 0.832 7.5 7.0 6.6 B82442T1563K050 B82442T1683K050 B82442T1823K050 100 120 150 20 20 20 0.796 0.796 0.796 510 440 410 760 670 610 0.99 1.29 1.50 6.1 5.3 4.6 B82442T1104K050 B82442T1124K050 B82442T1154K050 180 220 270 20 20 20 0.796 0.796 0.796 350 330 290 550 500 450 1.96 2.21 2.95 4.2 3.9 3.5 B82442T1184K050 B82442T1224K050 B82442T1274K050 330 390 470 20 20 20 0.796 0.796 0.796 280 260 240 430 390 350 3.29 3.70 4.73 3.4 3.0 2.6 B82442T1334K050 B82442T1394K050 B82442T1474K050 560 680 820 1000 20 20 20 30 0.796 0.796 0.796 0.252 220 210 170 150 320 300 270 246 5.21 5.87 7.86 9.5 2.4 2.3 2.2 1.8 B82442T1564K050 B82442T1684K050 B82442T1824K050 B82442T1105K050 Tolerance Qmin H 1.0 1.5 2.2 20% =^ M 3.3 4.7 6.8 10 12 15 10% =^ K Please read Cautions and warnings and Important notes at the end of this document. Page 5 of 9 fres, min MHz Ordering code 2010-07-05 SMT inductors – SIMID series SIMID 2220-T B82442T Characteristics and ordering codes LR Tolerance Qmin H 1200 1500 10% 5% fL;fQ MHz IR mA Isat mA Rmax fres, min MHz Ordering code1) 30 30 0.252 0.252 140 130 223 200 12.6 14.9 1.7 1.5 B82442T1125+050 B82442T1155+050 1800 2200 2700 30 30 30 0.252 0.252 0.252 110 100 90 183 168 151 19.7 22.5 29.5 1.4 1.2 1.1 B82442T1185+050 B82442T1225+050 B82442T1275+050 3300 3900 4700 30 30 30 0.252 0.252 0.252 85 74 73 138 127 119 32.8 43.5 48.6 1.0 0.9 0.8 B82442T1335+050 B82442T1395+050 B82442T1475+050 5600 6800 8200 10000 30 30 30 25 0.252 0.252 0.252 0.0796 66 65 54 46 109 102 92 81 54.7 60.3 80.6 112 0.8 0.6 0.6 0.5 B82442T1565+050 B82442T1685+050 B82442T1825+050 B82442T1106+050 =^ K =^ J Closer tolerances and intermediate values on request. Higher currents possible at temperatures <TR on request. Sample kit available. Ordering code: B82442X002 For more information refer to chapter “Sample kits”. 1) Replace the + by the code letter for the required inductance tolerance Please read Cautions and warnings and Important notes at the end of this document. Page 6 of 9 2010-07-05 SMT inductors – SIMID series SIMID 2220-T B82442T Impedance |Z| versus frequency f measured with impedance analyzer Agilent 4294A/E4991A, typical values at 20 °C Inductance L versus DC load current IDC measured with LCR meter Agilent 4285A, typical values at 20 °C Q factor versus frequency f measured with impedance analyzer Agilent 4294A/E4991A, typical values at 20 °C Current derating IOP/IR versus ambient temperature TA (rated temperature TR = 85 °C) Please read Cautions and warnings and Important notes at the end of this document. Page 7 of 9 2010-07-05 Cautions and warnings Please note the recommendations in our Inductors data book (latest edition) and in the data sheets. – Particular attention should be paid to the derating curves given there. – The soldering conditions should also be observed. Temperatures quoted in relation to wave soldering refer to the pin, not the housing. If the components are to be washed varnished it is necessary to check whether the washing varnish agent that is used has a negative effect on the wire insulation, any plastics that are used, or on glued joints. In particular, it is possible for washing varnish agent residues to have a negative effect in the long-term on wire insulation. The following points must be observed if the components are potted in customer applications: – Many potting materials shrink as they harden. They therefore exert a pressure on the plastic housing or core. This pressure can have a deleterious effect on electrical properties, and in extreme cases can damage the core or plastic housing mechanically. – It is necessary to check whether the potting material used attacks or destroys the wire insulation, plastics or glue. – The effect of the potting material can change the high-frequency behaviour of the components. Ferrites are sensitive to direct impact. This can cause the core material to flake, or lead to breakage of the core. Even for customer-specific products, conclusive validation of the component in the circuit can only be carried out by the customer. Please read Important notes at the end of this document. Page 8 of 9 2010-07-05 Important notes The following applies to all products named in this publication: 1. Some parts of this publication contain statements about the suitability of our products for certain areas of application. These statements are based on our knowledge of typical requirements that are often placed on our products in the areas of application concerned. We nevertheless expressly point out that such statements cannot be regarded as binding statements about the suitability of our products for a particular customer application. As a rule, EPCOS is either unfamiliar with individual customer applications or less familiar with them than the customers themselves. For these reasons, it is always ultimately incumbent on the customer to check and decide whether an EPCOS product with the properties described in the product specification is suitable for use in a particular customer application. 2. We also point out that in individual cases, a malfunction of electronic components or failure before the end of their usual service life cannot be completely ruled out in the current state of the art, even if they are operated as specified. In customer applications requiring a very high level of operational safety and especially in customer applications in which the malfunction or failure of an electronic component could endanger human life or health (e.g. in accident prevention or life-saving systems), it must therefore be ensured by means of suitable design of the customer application or other action taken by the customer (e.g. installation of protective circuitry or redundancy) that no injury or damage is sustained by third parties in the event of malfunction or failure of an electronic component. 3. The warnings, cautions and product-specific notes must be observed. 4. In order to satisfy certain technical requirements, some of the products described in this publication may contain substances subject to restrictions in certain jurisdictions (e.g. because they are classed as hazardous). Useful information on this will be found in our Material Data Sheets on the Internet (www.epcos.com/material). Should you have any more detailed questions, please contact our sales offices. 5. We constantly strive to improve our products. Consequently, the products described in this publication may change from time to time. The same is true of the corresponding product specifications. Please check therefore to what extent product descriptions and specifications contained in this publication are still applicable before or when you place an order. We also reserve the right to discontinue production and delivery of products. Consequently, we cannot guarantee that all products named in this publication will always be available. The aforementioned does not apply in the case of individual agreements deviating from the foregoing for customer-specific products. 6. Unless otherwise agreed in individual contracts, all orders are subject to the current version of the “General Terms of Delivery for Products and Services in the Electrical Industry” published by the German Electrical and Electronics Industry Association (ZVEI). 7. The trade names EPCOS, BAOKE, Alu-X, CeraDiode, CSMP, CSSP, CTVS, DeltaCap, DigiSiMic, DSSP, FormFit, MiniBlue, MiniCell, MKD, MKK, MLSC, MotorCap, PCC, PhaseCap, PhaseCube, PhaseMod, PhiCap, SIFERRIT, SIFI, SIKOREL, SilverCap, SIMDAD, SiMic, SIMID, SineFormer, SIOV, SIP5D, SIP5K, ThermoFuse, WindCap are trademarks registered or pending in Europe and in other countries. Further information will be found on the Internet at www.epcos.com/trademarks. Page 9 of 9