Vishay BRT21 Optocoupler, phototriac output, zero crossing Datasheet

BRT21/ 22/ 23
Vishay Semiconductors
Optocoupler, Phototriac Output, Zero Crossing
Features
•
•
•
•
High Input Sensitivity IFT = 1.0 mA
ITRMS = 300 mA
High Static dv/dt 10,000 V/µs
Electrically Insulated between Input and
Output circuit
• Microcomputer compatible
• Trigger Current
- (IFT < 1.2 mA) BRT22F, BRT23F,
- (IFT < 2 mA) BRT21H, BRT22H, BRT23H
- (IFT < 3 mA) BRT21M, BRT22M, BRT23M
•
•
•
•
•
Available Surface Mount and on on tape and reel
Zero Voltage Crossing detector
UL File E52744 System Code "J"
Lead-free component
Component in accordance to RoHS 2002/95/EC
and WEEE 2002/96/EC
Applications
• Industrial controls
• Office equipment
• Consumer appliances
Description
The BRT21, BRT22, BRT23 product family consists
of AC switch optocouplers with zero voltage detectors with two electrically insulated lateral power ICs
which integrate a thyrister system, a photo detector
and noise suppression at the output and an IR GaAs
diode input
High input sensitivity is achieved by using an emitter
follower phototransistor and an SCR predriver resulting in an LED trigger current of less than 2 mA or 3 mA
(DC). Inverse parallel SCRs provide commutating
dv/dt greater than 10 kV/µs
The zero cross line voltage detection circuit consists
of two MOSFETS and a photodiode.
THe BRT21/ 22/ 23 product family isolates low-voltage logic from 120, 230 and 380 VAC lines to control
resistive, inductive or capacitive loads including
motors, solenoids, high current thyristers or TRIAC
and relays.
Document Number 83690
Rev. 1.4, 10-Jan-05
A 1
6 MT2
C 2
5
NC 3
17223
ZCC*
NC
4 MT1
*Zero Crossing Circuit
Order Information
Part
Remarks
BRT21H
VDRM ≤ 400 V, DIP-6, 2.0 mA IFT
BRT21M
VDRM ≤ 400 V, DIP-6, 3.0 mA IFT
BRT22F
VDRM ≤ 600 V, DIP-6, 1.2 mA IFT
BRT22H
VDRM ≤ 600 V, DIP-6, 2.0 mA IFT
BRT22M
VDRM ≤ 600 V, DIP-6, 3.0 mA IFT
BRT23F
VDRM ≤ 800 V, DIP-6, 1.2 mA IFT
BRT23H
VDRM ≤ 800 V, DIP-6, 2.0 mA IFT
BRT23M
VDRM ≤ 800 V, DIP-6, 3.0 mA IFT
BRT21H-X006
VDRM ≤ 400 V, DIP-6 400 mil (option 6), 2.0 mA IFT
BRT21H-X007
VDRM ≤ 400 V, SMD-6 (option 7), 2.0 mA IFT
BRT21M-X006
VDRM ≤ 400 V, DIP-6 400 mil (option 6), 3.0 mA IFT
BRT22F-X006
VDRM ≤ 600 V, SMD-6 (option 7), 1.2 mA IFT
BRT22F-X0067 VDRM ≤ 600 V, SMD-6 (option 7), 1.2 mA IFT
BRT22H-X007
VDRM ≤ 600 V, SMD-6 (option 7), 2.0 mA IFT
BRT22M-X006
VDRM ≤ 600 V, DIP-6 400 mil (option 6), 3.0 mA IFT
BRT23F-X006
VDRM ≤ 800 V, DIP-6 400 mil (option 6), 1.2 mA IFT
BRT23F-X007
VDRM ≤ 800 V, DIP-6 400 mil (option 6), 1.2 mA IFT
BRT23H-X006
VDRM ≤ 800 V, DIP-6 400 mil (option 6), 2.0 mA IFT
BRT23H-X007
VDRM ≤ 800 V, SMD-6 (option 7), 2.0 mA IFT
BRT23M-X006
VDRM ≤ 800 V, DIP-6 400 mil (option 6), 3.0 mA IFT
BRT23M-X007
VDRM ≤ 800 V, SMD-6 (option 7), 3.0 mA IFT
For additional information on the available options refer to
Option Information.
www.vishay.com
1
BRT21/ 22/ 23
Vishay Semiconductors
Absolute Maximum Ratings
Tamb = 25 °C, unless otherwise specified
Stresses in excess of the absolute Maximum Ratings can cause permanent damage to the device. Functional operation of the device is
not implied at these or any other conditions in excess of those given in the operational sections of this document. Exposure to absolute
Maximum Rating for extended periods of the time can adversely affect reliability.
Input
Parameter
Symbol
Value
VR
6.0
V
IF
60
mA
Surge current
IFSM
2.5
A
Power dissipation
Pdiss
Reverse voltage
Test condition
IR = 10 µA
Forward current
Derate from 25 °C
Unit
100
mW
1.33
mW/°C
Output
Parameter
Peak off-state voltage
Test condition
ID(RMS) = 70 µA
Part
Symbol
Value
Unit
BRT21
VDM
400
V
BRT22
VDM
600
V
BRT23
VDM
800
V
ITM
300
mA
3.0
A
Pdiss
600
mW
6.6
mW/°C
RMS on-state current
Single cycle surge current
Power dissipation
Derate from 25 °C
Coupler
Parameter
Test condition
Isolation test voltage (between t = 1.0 min.
emitter and detector, climate per
DIN 500414, part 2, Nov. 74)
Symbol
Value
Unit
VISO
5300
VRMS
Pollution degree (DIN VDE
0109)
2
Creepage
≥ 7.0
mm
Clearance
≥ 7.0
mm
Comparative tracking index per
DIN IEC 112/VDE 0303 part 1,
group IIIa per DIN VDE 6110
≥ 175
Isolation resistance
VIO = 500 V, Tamb = 25 °C
VIO = 500 V, Tamb = 100 °C
Storage temperature range
Ambient temperature range
Soldering temperature
www.vishay.com
2
max. ≤ 10 sec. dip soldering
≥ 0.5 mm from case bottom
RIO
≥ 1012
Ω
RIO
≥ 1011
Ω
Tstg
- 55 to + 150
°C
Tamb
- 55 to + 100
°C
Tsld
260
°C
Document Number 83690
Rev. 1.4, 10-Jan-05
BRT21/ 22/ 23
Vishay Semiconductors
Electrical Characteristics
Tamb = 25 °C, unless otherwise specified
Minimum and maximum values are testing requirements. Typical values are characteristics of the device and are the result of engineering
evaluation. Typical values are for information only and are not part of the testing requirements.
Input
Typ.
Max
Forward voltage
Parameter
IF = 10 mA
Test condition
VF
1.16
1.35
V
Reverse current
VR = 6.0 V
IR
0.1
10
µA
Capacitance
VF = 0 V, f = 1.0 MHz
Thermal resistance, junction to
ambient
Symbol
Min
Unit
CO
25
pF
Rthja
750
K/W
Output
Parameter
Off-state voltage
Test condition
ID(RMS) = 70 µA
Repetitive peak off-state voltage IDRM = 100 µA
Off-state current
VD = VDRM, Tamb = 100 °C,
IF = 0 mA
Symbol
Min
Typ.
VD(RMS)
424
460
VDRM
600
Max
Unit
V
V
ID(RMS)
10
1.7
100
µA
On-state voltage
IT = 300 mA
VTM
3.0
V
On-state current
PF = 1.0, VT(RMS) = 1.7 V
ITM
300
mA
Surge (non-repetitive), on-state
current
f = 50 Hz
ITSM
3.0
A
Trigger current temp. gradient
Inhibit voltage temp. gradient
Off-state current in inhibit state
IF = IFT1, VDRM
Holding current
∆IFT1/∆Tj
7.0
14
µA/K
∆IFT2/∆Tj
7.0
14
µA/K
∆VDINH/∆Tj
-20
IDINH
50
200
µA
IH
65
500
µA
Latching current
VT = 2.2 V
IL
5.0
Zero cross inhibit voltage
IF = Rated IFT
VIH
15
Turn-on time
VRM = VDM = VD(RMS)
ton
35
Turn-off time
PF = 1.0, IT = 300 mA
Critical rate of rise of off-state
voltage
VD = 0.67 VDRM, TJ = 25 °C
VD = 0.67 VDRM, TJ = 80 °C
Critical rate of rise of voltage at
current commutation
VD = 0.67 VDRM,
di/dtcrq ≤ 15 A/ms, Tj = 25 °C
VD = 0.67 VDRM,
di/dtcrq ≤ 15 A/ms, Tj = 80 °C
toff
50
mA
25
V
µs
µs
10000
V/µs
dv/dtcr
5000
V/µs
dv/dtcrq
10000
V/µs
dv/dtcrq
5000
V/µs
Critical rate of rise of on-state
di/dtcr
8.0
A/µs
Thermal resistance, junction to
ambient
Rthja
Document Number 83690
Rev. 1.4, 10-Jan-05
dv/dtcr
mV/K
125
K/W
www.vishay.com
3
BRT21/ 22/ 23
Vishay Semiconductors
Coupler
Parameter
Critical rate of rise of coupled
input/output voltage
Test condition
Symbol
IT = 0 A, VRM = VDM = VD(RMS)
dvIO/dt
10000
V/µs
CCM
0.01
pF
Common mode coupling
capacitance
Min
Typ.
Max
Unit
Capacitance (input-output)
f = 1.0 MHz, VIO = 0 V
CIO
0.8
pF
Isolation resistance
VIO = 500 V, Tamb = 25 °C
Ris
≥ 10
Ω
VIO = 500 V, Tamb = 100 °C
Ris
≥ 1011
Trigger current
VD = 5.0 V, F - Versions
IFT
1.2
mA
VD = 5.0 V, H - Versions
IFT
2.0
mA
VD = 5.0 V, M - Versions
IFT
3.0
mA
12
Ω
Power Factor Considerations
www.vishay.com
4
1
Cs(µF) = 0.0032 (µF)* 10^(0.0066IL (mA)
Cs - Shunt Capacitance - µF
A snubber isn’t needed to eliminate false operation of
the TRIAC driver because of the high static and commutating dv/dt with loads between 1.0 and 0.8 power
factors. When inductive loads with power factors less
than 0.8 are being driven, include a RC snubber or a
single capacitor directly across the device to damp
the peak commutating dv/ dt spike. Normally a commutating dv/dt causes a turning-off device to stay on
due to the stored energy remaining in the turning-off
device.
But in the case of a zero voltage crossing optotriac,
the commutating dv/dt spikes can inhibit one half of
the TRIAC from turning on. If the spike potential
exceeds the inhibit voltage of the zero cross detection
circuit, half of the TRIAC will be heldoff and not turnon. This hold-off condition can be eliminated by using
a snubber or capacitor placed directly across the
optotriac as shown in Figure 1. Note that the value of
the capacitor increases as a function of the load current.
The hold-off condition also can be eliminated by providing a higher level of LED drive current. The higher
LED drive provides a larger photocurrent which
causes the phototransistor to turn-on before the commutating spike has activated the zero cross network.
Figure 2 shows the relationship of the LED drive for
power factors of less than 1.0. The curve shows that
if a device requires 1.5 mA for a resistive load, then
1.8 times 2.7 mA) that amount would be required to
control an inductive load whose power factor is less
than 0.3.
.1
Ta = 25°C, PF = 0.3
.01
IF = 2.0 mA
.001
0
iil410_01
50
100
150
200
250
300
350
400
IL - Load Current - mA(RMS)
Figure 1. Shunt Capacitance vs. Load Current
Document Number 83690
Rev. 1.4, 10-Jan-05
BRT21/ 22/ 23
Vishay Semiconductors
Typical Characteristics (Tamb = 25 °C unless otherwise specified)
150
IFth Normalized to IFth @ PF = 1.0
Ta = 25°C
1.8
LED - LED Power - mW
NIFth - Normalized LED
Trigger Current
2.0
1.6
1.4
1.2
1.0
0.8
0.0
0.2
0.4
0.6
0.8
PF - Power Factor
1.0
50
0
-60
1.2
iil410_05
iil410_02
100
Figure 2. Normalized LED Trigger Current vs. Power Factor
-40
-20
0
20
40
60
Ta - Ambient Temperature - °C
80
100
Figure 5. Maximum LED Power Dissipation
1.4
VF - Forward Voltage - V
1.3
Ta = -55°C
1.2
IT = f(VT),
parameter: Tj
Ta = 25°C
1.1
1.0
0.9
Ta = 85°C
0.8
0.7
.1
1
10
IF - Forward Current - mA
iil410_03
100
iil410_06
Figure 3. Forward Voltage vs. Forward Current
If(pk) - Peak LED Current - mA
10000
Figure 6. Typical Output Characteristics
τ
ITRMS=f(TA),
RthJA=150 K/W
Device switch
soldered in pcb
or base plate.
Duty Factor
1000
100
10
10 -6
.005
.01
.02
t
.05
.1
.2
.5
10 -5
iil410_04
DF =τ/t
10 -4 10 -3 10 -2 10 -1
t -LED Pulse Duration -s
10 0
101
Figure 4. Peak LED Current vs. Duty Factor, Tau
Document Number 83690
Rev. 1.4, 10-Jan-05
iil410_07
Figure 7. Current Reduction
www.vishay.com
5
BRT21/ 22/ 23
Vishay Semiconductors
40 to 60 Hz
line operation,
Ptot=f(ITRMS)
ITRMS=f(TPIN5), RthJ–PIN5=16.5 K/W
Thermocouple measurement must
be performed potentially separated
to A1 and A2. Measuring junction
as near as possible at the case.
iil410_08
iil410_11
Figure 8. Current Reduction
Figure 11. Power Dissipation 40 to 60 Hz Line Operation
tgd=f (IFIFT25°C), VD=200 V,
f=40 to 60 Hz, parameter: Tj
VDINHmin=f(IF/IFT25°C),
parameter: Tj
Device zero voltage
switch can be triggered
only in hatched area
below Tj curves.
iil410_12
iil410_09
Figure 9. Typical Trigger Delay Time
Figure 12. Typical Static Inhibit Voltage Limit
1
6
2
5
3
4
0.1 µF
220 V~
IDINH =f (IF/IFT25°C),
VD=600 V, parameter: Tj
iil410_13
iil410_10
Figure 10. Typical Inhibit Current
www.vishay.com
6
Figure 13. 1- Apply a Capacitor to the Supply Pins at the Load-Side
Document Number 83690
Rev. 1.4, 10-Jan-05
BRT21/ 22/ 23
Vishay Semiconductors
500 µH
33 Ω
1
6
2
5
3
4
22 nF
220 V~
1
6
2
5
3
4
22 nF
220 V~
iil410_15
iil410_14
Figure 14. 2 - Connect a Series Resistor to the Output and Bridge
Both by a Capacitor
Figure 15. 3 - Connect a Choke of Low Winding Cap. in Series,
e.g., a Ringcore Choke, with Higher Load Currents
Technical Information
See Application Note for additional information.
Package Dimensions in Inches (mm)
3
2
1
4
5
6
pin one ID
.248 (6.30)
.256 (6.50)
ISO Method A
.335 (8.50)
.343 (8.70)
.039
(1.00)
Min.
4°
typ .
.018 (0.46)
.020 (0.51)
.375 (9.53)
.395 (10.03)
.130 (3.30)
.150 (3.81)
.033 (0.84) typ.
.033 (0.84) typ.
.100 (2.54) typ
Document Number 83690
Rev. 1.4, 10-Jan-05
.300 (7.62)
ref.
.048 (1.22)
.052 (1.32)
.0040 (.102)
.0098 (.249)
.012 (.30) typ.
.020 (.51)
.040 (1.02)
15ı max.
17222
www.vishay.com
7
BRT21/ 22/ 23
Vishay Semiconductors
Option 6
Option 7
.407 (10.36)
.391 (9.96)
.307 (7.8)
.291 (7.4)
.300 (7.62)
TYP.
.028 (0.7)
MIN.
.180 (4.6)
.160 (4.1)
.315 (8.0)
MIN.
18487
www.vishay.com
8
.014 (0.35)
.010 (0.25)
.400 (10.16)
.430 (10.92)
.331 (8.4)
MIN.
.406 (10.3)
MAX.
Document Number 83690
Rev. 1.4, 10-Jan-05
BRT21/ 22/ 23
Vishay Semiconductors
Ozone Depleting Substances Policy Statement
It is the policy of Vishay Semiconductor GmbH to
1. Meet all present and future national and international statutory requirements.
2. Regularly and continuously improve the performance of our products, processes, distribution and
operatingsystems with respect to their impact on the health and safety of our employees and the public, as
well as their impact on the environment.
It is particular concern to control or eliminate releases of those substances into the atmosphere which are
known as ozone depleting substances (ODSs).
The Montreal Protocol (1987) and its London Amendments (1990) intend to severely restrict the use of ODSs
and forbid their use within the next ten years. Various national and international initiatives are pressing for an
earlier ban on these substances.
Vishay Semiconductor GmbH has been able to use its policy of continuous improvements to eliminate the use
of ODSs listed in the following documents.
1. Annex A, B and list of transitional substances of the Montreal Protocol and the London Amendments
respectively
2. Class I and II ozone depleting substances in the Clean Air Act Amendments of 1990 by the Environmental
Protection Agency (EPA) in the USA
3. Council Decision 88/540/EEC and 91/690/EEC Annex A, B and C (transitional substances) respectively.
Vishay Semiconductor GmbH can certify that our semiconductors are not manufactured with ozone depleting
substances and do not contain such substances.
We reserve the right to make changes to improve technical design
and may do so without further notice.
Parameters can vary in different applications. All operating parameters must be validated for each
customer application by the customer. Should the buyer use Vishay Semiconductors products for any
unintended or unauthorized application, the buyer shall indemnify Vishay Semiconductors against all
claims, costs, damages, and expenses, arising out of, directly or indirectly, any claim of personal
damage, injury or death associated with such unintended or unauthorized use.
Vishay Semiconductor GmbH, P.O.B. 3535, D-74025 Heilbronn, Germany
Telephone: 49 (0)7131 67 2831, Fax number: 49 (0)7131 67 2423
Document Number 83690
Rev. 1.4, 10-Jan-05
www.vishay.com
9